ASSEMBLY INSTRUCTIONS
DX-DRTVM102
Medium Low Profile Wall Mount with Optional -5° Tilt
For wood-stud, concrete-wall, or
concrete-bloack installation
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
3
TVs the wall mount fits
The wall mount fits TVs with M4, M5, or M6 screw holes that are the following distances apart:
13.78" (350 mm) maximum horizontal distance
Tools needed
You will need the following tools to assemble your new wall mount:
Edge-to-edge stud finder
Pencil
Tape measure
Hammer
Phillips screwdriver
Level
Socket wrench with 1/2" (13 mm)
socket or adjustable wrench
OR
Drill
7/32" (5.5 mm) wood drill
bit for wood stud wall
3/8" (10 mm) masonry
drill bit for concrete wall
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
5
Hardware
Package contents: hardware
Note: Not all hardware will be used.
Make sure you have all the hardware necessary to assemble your new wall mount:
Label
Hardware
Qty.
Label
Hardware
Qty.
11
4
M6 × 12 mm screw
04
2
5/16" × 2 3/4" lag bolt
(7.9 mm × 69.9 mm)
12
13
4
4
M6 × 20 mm screw
5/16"(7.9 mm)
washer
M6 × 35 mm
screw
05
06
2
2
14
8
M4/M5 washer
Concrete anchor
15
16
4
4
M6 washer
07
08
09
4
4
4
M4 × 12 mm screw
M4 × 30 mm
screw
M4/M5 spacer
M5 × 12 mm screw
17
4
M6 spacer
M5 × 30 mm
screw
10
4
1
2
3
4in
10
20
30
40
50
60
70
80
90
100mm
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DX-DRTVM102
Assembly instructions
Step 1: Adjust the tilt
Note: The tilt on the left TV bracket (02) and right TV bracket (03) must be the same.
1
2
Use a Phillips screwdriver to remove the two tilt screws (S) from the outside edges of each TV bracket (02
and 03).
To tilt the TV forward by 5°, push the tilt brackets on the left TV bracket (02) and right TV bracket (03) down.
OR
To keep the TV completely vertical, push tilt brackets on the left TV bracket (02) and right TV bracket (03) up.
Re-insert two tilt screws (S) into each TV brackets (02 and 03), then tighten the screws.
Caution: Do not over tighten the screws.
3
Option 1: Mount tilted -5°
&
Tilt bracket
&
&
02 03
02 03
S
S
Option 2: Mount not tilted
&
Tilt bracket
&
&
02 03
02 03
S
S
You’ll need:
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
7
Step 2: Determine whether your TV has a flat back or an irregular or obstructed back
1
2
Carefully place your TV screen face-down on a cushioned, clean surface to protect the screen from damages and
scratches.
If your TV has a table-top stand attached, remove the stand. See the documentation that came with your TV for
instructions.
3
Align the screw holes in the brackets with the mounting screw holes on your TV. Position the brackets so they do
not extend above or below your TV and do not cover any connectors or jacks. Make note of which bracket screw
holes you will use.
If the brackets lay flush against the back of your TV and do not block any jacks, your TV has a flat back.
If there is a gap between a bracket and some part of the back of your TV, your TV has an irregularly-shaped back.
If a bracket blocks any jacks, your TV has an obstructed back. In either case, you need spacers.
Flat back (no spacers needed)
Obstructed back (spacers needed)
Irregular back (spacers needed)
4
Remove the brackets.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DX-DRTVM102
Step 3: Select screws and spacers
1
Select the hardware for your TV (screws, washers, and spacers). See the documentation that came with your TV
for screw length and diameter.
Select one of the following types of screws:
M4 × 12 mm screws (07)
M4 × 30 mm screws (08)
M5 × 12 mm screws (09)
M5 × 30 mm screws (10)
M6 × 12 mm screws (11)
M6 × 20 mm screws (12)
M6 × 35 mm screws (13)
Select one of the following types of washers:
M4/M5 washers (14)
M6 washers (15)
For an irregular or obstructed TV back, select one of the following types of spacers:
M4/M5 spacers (16) M6 spacers (17)
2
Hand thread screws into the threaded screw holes on the back of your TV to determine the correct screw
diameter and length. If your TV has an irregular or obstructed back, place a spacer between your TV back and the
screw to make sure you have the correct length.
Caution: To avoid potential personal injuries and property damage,
make sure that there are adequate threads to secure the brackets to
your TV. If you encounter resistance, stop immediately and contact
customer service. Use the shortest screw and spacer combination to
accommodate your TV. Using hardware that is too long may damage
your TV. However, using a screw that is too short may cause your TV
to fall from the mount.
Screw is
too long
Screw fits
correctly
Screw is
too short
3
Remove the screws.
For a flat back TV, go to “Step 4: Install the TV brackets Option 1: Installing for a TV with a flat back” on
page 9.
For an irregular or obstructed back, go to “Step 4: Install the TV brackets (continued) Option 2: Installing
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
9
Step 4: Install the TV brackets
Option 1: Installing for a TV with a flat back
1
Align the holes you noted on the left TV bracket (02) and right TV bracket (03) with the screw holes on the back
of your TV. The brackets are marked “R” for the right bracket and “L” for the left bracket.
2
Place the M4/M5 washers (14) or M6 washers (15) over the holes in the TV brackets that align with the screw
holes on the back of your TV, then insert the M4 screws (07), M5 screws (09), or M6 screws (11 or 12).
3
Tighten the screws until they are snug against the TV bracket. Do not over tighten.
03
02
&
02
03
14
15
OR
7
9
11 OR 12
You’ll need:
Screws
Washers
OR
11 (4)
OR
OR
OR
14 (4)
15 (4)
07 (4)
09 (4)
Phillips screwdriver
12 (4)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
10
DX-DRTVM102
Step 4: Install the TV brackets (continued)
Option 2: Installing for a TV with an irregular or obstructed back
1
2
3
Place M4/M5 spacers (16) or M6 spacers (17) over the mounting holes in the back of your TV.
If you are using M4 or M5 screws, place M4/M5 washers (14) over the spacers.
Align the holes you noted on the left TV bracket (02) and right TV bracket (03) with the spacers. The brackets are
marked “R” for the right bracket and “L” for the left bracket.
4
5
Place M4/M5 washers (14) or M6 washers (15) over the holes in the TV brackets, then insert M4 screws (08),
M5 screws (10), or M6 screws (13).
Tighten the screws until they are snug against the TV bracket. Do not over tighten.
03
02
16
17
02
OR
14
03
14 OR 15
8
10 OR 13
&
You’ll need:
Screws
Washers
OR
Spacers
OR
OR
OR
08 (4)
10 (4)
13 (4)
14 (8)
15 (4)
16 (4)
17 (4)
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
11
Step 5: Determine the wall-mount location.
Note: For help with determining where you need to drill screw holes, use the HeightFinder™ Installation Assistant at:
The center of your TV will match the center of the wall plate (01). Before you drill holes in the wall:
1
Measure the distance between the middle of one of the TV brackets and the bottom of your TV. This
measurement is A.
2
If you plan to place furniture (such as an entertainment center or TV stand) under your TV, measure the height of
the furniture and any items on top of the furniture. This measurement is B.
3
4
5
Measure the distance between the top of the furniture and where you want the bottom of your TV. This
measurement is C.
Add A + B + C. The total measurement is the height where you want the center of the wall plate (01) to be on the
wall.
Use a pencil to mark this spot on the wall.
A
C
B
You’ll need:
Measuring tape
Pencil
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
12
DX-DRTVM102
Step 6: Mount the wall plate
Note: Any material covering the wall (such as sheetrock) must not exceed 5/8" (16 mm).
Option 1: Mounting on a wood-stud wall
1
Locate the studs. Verify the center of the stud with an edge-to-edge stud finder.
2
At the wall height you determined in the previous step, align the wall plate (01) against the wall and make sure
that it is level. Use a pencil to mark the screw hole locations, then remove the wall plate.
3
4
Drill pilot holes to a depth of 3" (75 mm) using a 7/32" (5.5 mm) diameter drill bit.
Align the wall plate with the pilot holes, then place the washers (05) over the holes in the wall plate. Insert the lag
bolts (04) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the wall
plate.
Caution: Avoid potential injuries or property damage! DO NOT over-tighten the lag bolts (04).
< 5/8"
(16 mm)
01
04
05
3" (75 mm)
01
You’ll need:
05 (2)
04 (2)
Stud
finder
Pencil
Level
Drill
7/32" (5.5 mm) Socket wrench with
wood drill
1/2" (13 mm) socket
or adjustable wrench
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
13
Step 6: Mount the wall plate (continued)
Note: Any material covering the wall (such as sheetrock) must not exceed 5/8" (16 mm).
Option 2: Mounting on a solid concrete or concrete block wall
1
2
3
Level the wall plate (01) and mark the hole locations.
Drill pilot holes to a depth of 3" (75 mm) using a 3/8 in. (10 mm) diameter masonry drill bit.
Insert concrete wall anchors (06) into the pilot holes and make sure that the anchors are seated flush with the
concrete surface.
4
Align the wall plate with the anchors. Place washers (05) over the screw holes in the wall plate, insert
lag bolts (04) through the washers, then tighten the lag bolts only until the washers are pulled firmly against the
wall plate.
Warning: Avoid potential injuries or property damage. DO NOT over-tighten the lag bolts (04).
3" (75 mm)
Never drill into
01
the mortar
between blocks.
06
06
01
04
06
05
You’ll need:
06 (2)
Pencil
05 (2)
04 (2)
Drill
3/8" (10 mm)
masonry drill
bit
Hammer
Socket wrench with
1/2" (13 mm) socket
or adjustable wrench
Level
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
14
DX-DRTVM102
Step 7: Mount the TV on the wall plate
Lower the TV onto the wall plate (01) making sure that the hooks on the top of the left and right TV brackets (02 and
03) slide over the top of the wall plate and the hooks on the bottom of the TV brackets slide under the bottom of the
wall plate. Make sure that the TV is securely attached to the wall plate.
03
01
The TV is heavy. You
will need assistance
with this step.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-DRTVM102
15
Removing the TV from the wall plate
Simultaneously pull down on the two release cords on the TV brackets (02 and 03), then lift the TV up and away from
the wall plate.
For customer service, call: 800-305-2204 (U.S./Canada markets)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2011 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
6907-002033 <01>
12-0552
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|