1800W
TABLE SAW
TS1800
INSTRUCTION MANUAL
Code: TS1800
Date: 060913
Black
Cyan
Magenta
Yellow
Edition: 02
Op: DCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Description of symbols
Your new GMC power tool will more than satisfy
your expectations. It has been manufactured under
stringent GMC Quality Standards to meet superior
performance criteria.
The rating plate on your tool may show symbols.
These represent important information about the
product or instructions on its use.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years
of dependable service.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Conforms to relevant standards
for electromagnetic compatibility.
Specifications
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Voltage:
230–240Vac ~ 50Hz
1800W
4500 min-1
Input power:
No load speed:
Blade diameter:
Blade bore size:
Blade teeth:
Environmental protection
250mm
Recycle unwanted materials instead
of disposing of them as waste. All tools,
hoses and packaging should be sorted,
taken to the local recycling centre and
disposed of in an environmentally safe way.
16mm
40
Bevel range:
0° to 45°
610mm x 470mm
900mm
Table size:
Table height:
Depth of cut at 90°:
Depth of cut at 45°:
80mm
55mm
3
Download from Www.Somanuals.com. All Manuals Search And Download.
7. Dress correctly. Do not wear loose clothing or jewellery.
They can be caught in moving parts. Rubber gloves and
non-slip footwear are recommended when working outdoors.
If you have long hair, wear a protective hair covering.
General safety instructions
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who use
and service the machine have to be acquainted with this
Manual and must be informed about its potential hazards.
Children and infirm people must not use this tool. Children
should be supervised at all times if they are in the area in
which the tool is being used. It is also imperative that you
observe the accident prevention regulations in force in your
area. The same applies for general rules of occupational
health and safety.
8. Use safety accessories. Safety glasses and earmuffs
should always be worn. A face or dust mask is also
required if the sanding operation creates dust.
9. Do not abuse the power cord. Never pull the cord
to disconnect the tool from the power point. Keep the
cord away from heat, oil and sharp edges.
10. Secure the work piece. Use clamps or a vice to hold
the work piece. It is safer than using your hand and
frees both hands to operate the tool.
WARNING. When using power tools, basic safety
precautions should always be taken to reduce the risk
of fire, electric shock and personal injury. Also, please
read and heed the advice given in the additional important
safety instructions.
11. Do not overreach. Keep your footing secure and
balanced at all times.
12. Look after your tools. Keep tools sharp and clean for
better and safer performance. Follow the instructions
regarding lubrication and accessory changes. Inspect tool
cords periodically and, if damaged, have them repaired
by an authorised service facility. Inspect extension cords
periodically and replace them if damaged. Keep tool
handles dry, clean and free from oil and grease.
1. Keep the work area clean and tidy. Cluttered work
areas and benches invite accidents and injury.
2. Consider the environment in which you are working.
Do not use power tools in damp or wet locations. Keep
the work area well lit. Do not expose power tools to rain.
Do not use power tools in the presence of flammable
liquids or gases.
13. Disconnect idle tools. Switch off the power and
disconnect the plug from the power point before
servicing, when changing accessories and when the
tool is not in use.
3. Keep visitors away from the work area. All visitors and
onlookers, especially children and infirm persons, should
be kept well away from where you are working. Do not
let others in the vicinity make contact with the tool or
extension cord.
14. Remove adjusting keys and wrenches. Check to see
that keys and adjusting wrenches are removed from the
tool before switching on.
4. Store tools safely. When not in use, tools should be
locked up out of reach.
15. Avoid unintentional starting. Always check that the
switch is in the OFF position before plugging in the tool
to the power supply. Do not carry a plugged in tool with
your finger on the switch.
5. Do not force the tool. The tool will do the job better and
safer working at the rate for which it was designed.
6. Use the correct tool for the job. Do not force small
tools or attachments to do the job best handled by a
heavier duty tool. Never use a tool for a purpose for
which it was not intended.
16. Use outdoor rated extension cords. When a tool
is used outdoors, use only extension cords that are
intended for outdoor use and are so marked.
17. Stay alert. Watch what you are doing. Use common
sense. Do not operate a power tool when you are tired.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
• Wear suitable work clothes! Loose garments or jewellery
may become caught up in the rotating saw blade.
18. Check for damaged parts. Before using a tool, check
that there are no damaged parts. If a part is slightly
damaged, carefully determine if it will operate properly
and perform its intended function. Check for alignment of
moving parts, binding of moving parts, breakage of parts,
proper mounting and any other conditions that may affect
the operation of the tool. A part that is damaged should
be properly repaired or replaced by an authorised service
facility, unless otherwise indicated in this Instruction
Manual. Defective switches must be replaced by an
authorised service facility. Do not use a tool if the switch
does not turn the tool on and off correctly.
• Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allowed
to use the machine under supervision.
• Keep children and infirm people away from the machine
when it is connected to the power supply.
• Check the power cord. Never use a faulty or damaged
power cord.
• If the cordset is damaged take the saw to an authorised
service centre for repair or replacement
• Never attempt any repairs yourself, always take it to an
authorised service centre for repair or parts replacement.
19. Guard against electric shock. Prevent body contact
with grounded objects such as water pipes, radiators,
cookers and refrigerator enclosures.
• Keep the saw table and your workplace clean of wood
scrap and any unnecessary objects.
20. Use only approved parts. When servicing, use only
identical replacement parts. Use an authorised service
facility to fit replacement parts.
• Keep the area free of tripping hazards.
• Persons working with the machine should not be distracted.
• Note the direction of rotation of the motor and saw blade.
Additional safety rules for table saws
• Always pull the plug out of the power socket before
adjusting or servicing the machine.
• After you have switched off the motor, never slow down
the saw blade by applying pressure to its side.
• Give these safety regulations to all persons who
work on the machine.
• Fit only blades which are well sharpened and have no
cracks or deformations.
• Do not use this saw to cut firewood.
• The machine is to be operated only with a saw blade
from a reputable supplier.
• CAUTION. Hands and fingers may be injured on the
rotating saw blade.
• Faulty saw blades have to be replaced immediately.
• Before you use the machine for the first time, check that
the voltage marked on the rating plate is the same as
your mains voltage.
• Never use saw blades, which do not comply with the data
specified in this manual.
• Make sure that the arrow on the saw blade complies with
the arrow marked on the machine.
• If you need to use an extension cable, make sure its
conductor cross-section is large enough for the saw’s
power consumption. Minimum cross-section: 1.0mm2.
• Never dismantle the machine’s safety devices or put
them out of operation.
• Do not use or leave the saw in the rain and never use it
in damp, humid, or wet conditions.
• Damaged or faulty safety devices have to be replaced
immediately.
• Provide good lighting.
• Never cut a work piece, which is too small to hold securely.
• Never saw near combustible liquids or gases.
• If you are interrupted when operating the saw, complete
the process and switch off before looking up.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• Periodically check that all nuts, bolts and other fixings are
properly tightened.
• It is imperative to observe the accident prevention
regulations in force in your area as well as all other
generally recognised rules of safety.
• Do not store materials or equipment above a machine in
such a way that they could fall into it.
• The machine may be used in closed room only in
conjunction with a suitable vacuum extraction system.
• Always ensure that your work is on the table. Never use
the tool to cut pieces that are not on the table.
• This table saw must be connected to a 230–240V
socket-outlet with a minimum 10A circuit.
• Do not place your hands in awkward positions where one
or both may slip suddenly and touch the saw blade.
• Never use the cord for any purpose other than that
for which it is intended!
• When working with a long work piece, use an additional
support such as a saw table to prevent the blade from
grabbing the work.
• Adopt a firm standing position and keep your balance
at all times.
• When cutting round wood, use clamps that prevent the
work piece from turning on the table.
• Check the tool for signs of damage!
• Before you use the tool it is imperative to check that
its safety devices and any slightly damaged parts are
working properly and in the way intended.
• There must be no nails or other foreign bodies in that part
of the work piece you want to cut.
• Always stand to the side of the saw blade when working
with the saw.
• Check that the moving parts work properly and do not
jam or whether any of the parts are damaged. All parts
must be fitted correctly and satisfy all conditions for the
tool to work properly.
• Never load the machine so much that it slows down and
over-heats.
• Unless otherwise stated in these instructions, damaged
safety devices and parts must be repaired or replaced
by an authorised service facility.
• Never saw several work pieces simultaneously.
• Use the push stick provided with the tool when cutting
along or across narrow work pieces.
• Have damaged switches replaced by an authorised
service facility.
• Never remove loose splinters, chips or jammed pieces of
wood when the saw blade is running.
• This tool complies with the pertinent safety regulations.
Repairs are to be carried out only by qualified electricians
at authorised service centres, using original replacement
parts. The user may suffer an accident if this condition is
not observed.
• To rectify faults or remove jammed pieces of wood, always
switch off the machine first and remove the mains plug!
• Adjustments, measurements and cleaning jobs are to be
performed only when the motor is switched off and the
mains plug removed!
• Rebating or grooving should not be carried out unless
suitable guarding, such as a tunnel guard, is fitted above
the table saw.
• Before you switch on the machine, check that all
wrenches and adjustment tools have been removed.
• When you leave your workplace, switch off the motor and
pull out the power plug.
• Saws shall not be used for slotting (stopped groove).
Wear goggles
• All guards and safety devices have to be refitted immediately
after completion of any repairs or maintenance.
Wear earmuffs
Wear a breathing mask
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Before using the table saw
Due to modern mass production techniques, it is unlikely
that your GMC Power Tool is faulty or that a part is missing.
If you find anything wrong, do not operate the tool until the
parts have been replaced or the fault has been rectified.
Failure to do so could result in serious personal injury.
1. Turn the table top and body upside down on a piece
of card to protect the table surface.
2. Remove the 6 screws securing the base plate
and take off the base plate.
3. Take out the polystyrene foam around the motor pack
to protect it during transport.
1. Remove all loose parts from the carton.
2. Remove the packing materials from around the saw.
4. Replace the base plate and add the 6 screws.
3. Carefully lift the saw from the carton and place it on
a level work surface.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your product
7
9
15
6
2
1
Before using the saw, familiarise
yourself with all the operating features
and safety requirements.
1. Table top
2. Table insert
3. On/off switch
4. Riving knife
11
10
8
14
5. Saw blade
6. Blade guard
13
16
20
21
7. Rip fence
8. Rip fence locking lever
9. Rip fence scale
12
3
10. Mitre gauge
11. Mitre gauge locking knob
12. Blade height adjustment handle
13. Blade height locking knob
14. Bevel angle locking knob
15. Bevel angle pointer
16. Bevel angle scale
17. Dust extraction port
18. Stand
19. Rubber foot (x4)
20. Push stick
21. Push stick mounting brackets
22. Blade change spanners (x2)
23. Hex key
18
19
17
4
23
22
5
8
Download from Www.Somanuals.com. All Manuals Search And Download.
b
d
Components
The GMC TS1800 is supplied with th
following components:
a. Table saw body fitted with carbid
tipped saw blade
c
b. Height adjustment handle
c. Height adjustment locking knob
d. Blade guard
h
g
e. Riving knife
e
f
f. Mitre gauge
g. Rip fence
i
h. Push stick mounting brackets x 2
i. Phillips head screws and washers x 4
j. Push stick
k
j
k. Blade change spanner x 2
l. 5mm Hex key
l
Stand components
m. Legs x 4 (marked A)
n. Short upper braces x 2 (marked B)
o. Long upper braces x 2 (marked C)
p. Long middle braces x 2 (marked E)
q. Short middle braces x 2 (marked F)
r. Rubber feet x 4
p
n
q
m
o
s. Carriage bolt with spring washer,
flat washer and nut x 32
t. 65mm hex head bolt
with 2 flat washers,
r
t
u
s
spring washer and nut x 2
u. 50mm hex head bolt
with 2 flat washers,
spring washer and nut x 2
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembling the stand
Fitting the table saw to the stand
1. Make sure the blade is completely retracted into the
table top.
2. Align the holes on the stand with the matching holes
in the base of the table saw, the holes at the front of
the table top are further apart than the holes at the back
of the table saw housing.
A
B
C
D
E
CAUTION. Always pull out
the mains power plug before
carrying out any maintenance,
conversion or assembly work
on the table saw.
When assembling the stand it is
recommended that the screws are
only lightly tightened until the
stand is fully assembled.
3. Secure the front of the table saw to the stand using
2 65mm hex head bolts with 2 flat washers, spring
washer and nut (t) (Fig. F).
1. Use four carriage bolts, spring
washers, flat washers and
nuts (s) to fit a short middle
brace (q) between two stand
legs (m) (Fig. A).
4. Secure the rear of the table saw to the stand using
2 50mm hex head bolts with 2 flat washers, spring
washer and nut (u) (Fig. G).
F
G
2. Connect a second short
middle brace (q) to the second
pair of stand legs (m).
3. Use eight carriage bolts,
spring washers, flat washers
and nuts (s) to fit the
remaining two long middle
braces (p) (Fig. B).
5. Fully tighten all screws and nuts.
4. Use four carriage bolts, spring
washers, flat washers and
nuts (s) to attach each short
upper brace (n) to the top of
the stand (Fig. C).
Fitting the push stick mounting brackets
1. Fit the 2 push stick mounting
brackets to the right hand side
of the table saw.
2. Use 2 Phillips head screws
and washers (i) to attach each
mounting bracket (Fig. H).
H
5. Use four carriage bolts, spring
washers, flat washers and
nuts (s) to attach each long
upper brace (o) to the top of
the stand (Fig. D).
3. Slide the push stick into the
brackets to hold it in position.
Fitting the height adjustment handle
and locking knob
1. Fit the height adjustment locking knob onto the shaft at the
front of the table saw ensuring that the flat on the inside of
the knob locates on the flat at the rear of the shaft (Fig. I).
6. Add a rubber foot (r) to the
base of each stand leg (m)
(Fig. E).
7. Tighten all bolts and place the
stand on its feet.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Secure the height adjustment knob by tightening the
Phillips head screw (Fig. J).
3. Tighten the height adjustment locking knob.
4. Using the hex key provided, loosen the two hex bolts on
the riving knife clamp and insert the riving knife between
the two metal plates that form this clamp (Fig. O).
I
J
5. Adjust the position of the riving knife so that the gap between
the knife and the teeth of the blade is even along the
curve of the blade and is not less than 5mm wide (Fig. P).
O
P
3. Fit the height adjustment handle onto the shaft ensuring
that the flat on the handle locates onto the flat at the front
of the shaft (Fig. K).
4. Secure the height adjustment handle by tightening the
Phillips head screw (Fig. L).
6. Tighten the 2 hex screws to secure the riving knife in position.
7. Replace the table insert and secure using the 8 screws.
K
L
Fitting the blade guard
Q
1. Remove the hex nut and
washer on the side of the
guard (Fig. Q).
2. Remove the screw from
within the guard.
Fitting the riving knife
1. Remove the 8 screws securing the table insert and take
off the table insert (Fig. M).
2. Loosen the height adjustment locking knob and turn the
blade height adjustment handle to raise the blade to its
highest position (Fig. N).
3. Place the blade guard over the
riving knife so that the hole in
the guard and the hole in the riving knife are aligned (Fig. R).
4. Insert the screw through the hole and secure using the
nut and flat washer (Fig. S).
S
M
R
N
11
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Tighten the nut sufficiently so that the guard rests on the
table top but will lift when the workpiece is pushed into
the blade.
Adjusting the cutting depth
WARNING. The height locking
knob must be loosened before
the blade height is adjusted, and
re-tightened once the desired
setting is reached.
W
Note. The blade guard should return to its rest position after
the workpiece has been cut.
CAUTION. The saw blade guard must be in position at all
times to prevent contact with the blade. It should lift up and
onto the workpiece when the workpiece is passed through
the saw.
1. Set the saw blade to the
required cutting depth by
turning the height adjustment
handle (Fig. W).
Dust extraction
1. A suitable dust extraction
T
2. Turning the handle anti-clockwise increases the
cutting depth.
system or household vacuum
cleaner can be connected to
the dust extraction port for a
cleaner working environment
(Fig. T).
3. Turning the handle clockwise decreases the cutting depth.
Adjusting the blade angle
1. Loosen the bevel angle
knob and using the height
adjustment locking knob push
the blade assembly to the left
or right until the pointer points
to the required angle on the
bevel scale (Fig. X).
X
Turning on and off
1. To turn the table saw ON, press the green push button
marked I (Fig. U).
2. To turn the table saw OFF, press the red push button
marked O (Fig. V).
2. Retighten the bevel angle
knob once the required setting
is reached.
U
V
3. The blade angle pointer can be adjusted when checking the
accuracy of the blade angle. With the power disconnected,
place a set square against the saw blade. Adjust the blade
angle until the blade is parallel to the set square then move
the pointer to 0° on the blade angle scale.
Using the rip fence
1. Use the rip fence when
making longitudinal cuts.
2. The rip fence is fitted to the
table top on either side of the
blade (Fig. Y).
Note. This saw is fitted with an electromagnetic switch. In
the case where the power supply is turned off to the saw,
the saw must be turned on by pressing the green ON button
after the power supply is reconnected.
Y
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lift the rip fence locking
lever and slide the fence to
the required position. Use
the scale as a guide for the
distance between the blade
and the rip fence (Fig. Z).
Freehand. Performing a cut without a fence, mitre gauge,
fixture, hold down or other proper device to keep the
workpiece from twisting during the cut.
Z
Kickback. An uncontrolled grabbing and throwing of the
workpiece back toward the front of the saw.
Riving Knife. Also known as a separator or spreader.
The riving knife is a metal piece slightly thinner than the
saw blade which helps keep the kerf open during cutting
operations and prevents kickback.
4. Retighten the fence locking
lever.
Using the mitre gauge
Push Stick. A device used to feed the workpiece through
the saw during narrow ripping-type operation and helps
keep the operator’s hands well away from the blade.
1. Slide the mitre gauge into the slot of the table top on the
left or right hand side of the blade (Fig. a).
2. Loosen the locking knob on the mitre gauge (Fig. b).
Push Block. A device used for ripping-type operations too
narrow to allow use of a push stick.
a
b
Push sticks
A push stick should always be
used if your hand gets within
125mm (5”) of the saw blade.
c
Handle
A push stick is a safety device
that helps to keep your hands
and fingers away from the saw
blade. A handle helps to apply
pressure to the workpiece whilst
Notch to help
push wood
3. Rotate the mitre gauge to select the required angle.
4. Re-tighten the locking knob.
Notch to help
prevent hand
from slipping
a notch at the front of the push
Operation
stick fits onto the edge of the wood to help push it through
the saw. A push stick can be easily made from a scrap
piece of material. The push stick must be narrower than
the workpiece. Please refer to the diagram which depicts a
push stick (Fig. c).
The table saw can be used to make a variety of cuts including
longitudinal cuts, bevel cuts and mitre cross cuts. The below
section defines a common list of table saw terms:
Through Sawing. Any cutting operation where the blade
extends completely through the thickness of the workpiece.
Kickback
Non-Through Sawing. Any cutting operation where the
Kickback occurs when the blade stalls or binds, kicking the
workpiece back towards the front of the saw. Kickback can
cause serious injury. Precautions must be taken to avoid
kickback. The following conditions can cause kickback and
should be avoided.
blade does not extend through the workpiece.
Rip Cut. A cutting or shaping operation made along the
length or grain of the workpiece.
Cross Cut. A cut or shaping operation made across the
width of the workpiece cutting the workpiece to length.
• Making a cut with the incorrect blade depth.
• Attempting to saw through knots or nails in the workpiece.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
• Twisting the wood while making a cut.
1. Longitudinal cuts involve cutting through a workpiece
along its full length.
• Failing to correctly position the riving knife.
2. One edge of the workpiece is pressed against the rip
fence while its flat side rests on the table top.
• Making a cut with a dull, gummed-up
or improperly set blade.
3. The saw blade guard must always be operational
and cover the workpiece.
• Failing to support large workpieces.
• Forcing the workpiece through the saw blade.
• Cutting warped or wet lumber.
4. When making longitudinal cuts you must always
stand to one side of the cutting line.
• Not following correct operating procedures.
• Using the wrong blade for the type of cut.
5. Set the fence to suit the required width.
6. Switch on the table saw.
Tips to avoid kickback
1. Always use the correct blade depth setting. The top of the
blade teeth should clear the workpiece by 3mm to 6mm.
7. With your fingers together, place your hands flat on the
workpiece and push the workpiece along the fence into
the saw blade.
8. Guide the workpiece at the side with your left hand only
as far as the front edge of the guard hood.
2. Inspect the workpiece for knots or nails before beginning
a cut. Knock out any loose knots with a hammer. Never
saw into a loose knot or nail.
9. Always push the workpiece through to the end of the
riving knife.
3. Make straight cuts. Always use the rip fence when rip
cutting. This helps prevent twisting the wood in the cut.
10. Leave the off-cuts on the saw table until the saw blade
has stopped again.
4. Always use clean, sharp, properly-set blades. Never
make a cut with a dull blade.
11. Secure a long workpiece against sagging at the end of the
cutting operation (e.g. with a roller stand or similar device).
5. To avoid pinching the blade, support the workpiece
properly before beginning a cut.
12. Use the push stick for guiding the workpiece if your
hand gets to within 125mm (5”) of the saw blade.
6. When making a cut, use steady, even pressure.
Never force a cut.
13. After using the push stick, place it back on the holder.
7. Do not cut wet or warped lumber.
Cutting a narrow workpiece
8. Always hold your workpiece firmly with both hands or use
push blocks, push sticks, and feather boards to keep your
body in a balanced position to be able to resist kickback
should it occur.
Longitudinal cuts in a workpiece smaller than 125mm (5”) in
width must always be made with the help of the push stick.
WARNING. Worn or damaged push sticks must be replaced
immediately.
9. Use the right type of blade for the cut being made.
Cutting an extremely narrow workpiece
Longitudinal cuts in an extremely narrow workpiece with a
width of 30mm or less must always be made with the help
of a push block.
This table saw is not supplied with a push block. (Either
make or purchase a suitable one from a specialist dealer).
Making longitudinal cuts
IMPORTANT. After each new adjustment it is advisable to
carry out a trial cut in order to check the set dimensions.
After switching on the saw, wait for the blade to reach its
maximum speed of rotation before commencing with the
cut. Take extra care when starting the cut.
WARNING. Worn push blocks must be replaced without delay.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Loosen and remove the
screws securing the table
insert.
Making bevel cuts
1. Always use the fence when cutting bevels.
2. Set the saw blade to the required angle using the bevel
adjustment knob.
3. Set the fence to suit the width and height of the workpiece.
4. Carry out the cut in accordance with the workpiece width.
d
4. Take out the table insert.
5. Remove the riving knife
assembly (Fig. e).
6. Use the spanner supplied to lock
the spindle in position (Fig. f).
Making cross cuts
WARNING. When cross cutting, do not use the rip fence as
a length stop as the cut off piece could bind between the
fence and the blade and cause kickback.
e
f
1. Push the mitre gauge into one of the two slots of the
table saw and set it to the required angle. If you also
want to set the saw blade at an angle, use the slot, which
prevents your hand and the mitre gauge coming into
contact with the saw blade.
2. Press the workpiece firmly against the mitre gauge.
3. Switch on the saw.
7. Use the second spanner supplied to undo the blade bolt by
turning it in an anti-clockwise direction (right-hand thread)
(Fig. g).
4. Push the mitre gauge and the workpiece toward the saw
blade in order to make the cut.
8. Take off the outer flange and remove it and the saw blade
(Fig. h).
IMPORTANT. Always hold the guided part of the workpiece.
Never hold that part of the workpiece, which is being cut
off. Always push the mitre gauge far enough forward for the
workpiece to be cut through completely.
g
h
5. Switch off the saw.
6. Wait for the saw blade to stop before removing the off-cuts.
Changing the saw blade
WARNING. Switch off the table saw and remove the
mains power plug before carrying out any adjustments,
maintenance work or blade changes. Wear work gloves
when handling or fitting the blade.
9. Carefully clean the saw blade flanges before fitting the
new blade.
10. Insert and secure the saw blade in reverse order.
1. Loosen the height adjustment locking knob and turn the
height adjustment handle until the saw blade is at its
maximum height.
CAUTION. Take note of the direction of blade rotation.
The cutting edge of the teeth must point in the running
direction, i.e. forward (refer to the arrow on the saw blade).
2. Remove the blade guard assembly (Fig. d).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
11. Re-fit and re-set the riving knife and the saw blade guard.
12. Replace the table insert.
Maintenance
WARNING. Always ensure that the tool is switched off and
the plug is removed from the power point before making
and adjustments or maintenance procedures.
13. Before using the saw again, check that all safety
devices are in good working order.
IMPORTANT. After replacing the saw blade, make sure the
saw blade runs freely by turning the blade by hand.
Power cord maintenance
If the supply cord needs replacing, the task must be carried
out by the manufacturer, the manufacturer’s agent, or an
authorised service centre in order to avoid a safety hazard.
14. Plug the machine into a mains socket and run the saw at
no load before using it to cut any materials.
Cleaning
1. Keep the tool’s air vents unclogged and clean at all times.
2. Remove dust and dirt regularly. Cleaning is best done
with a soft brush or a rag.
3. Re-lubricate all moving parts at regular intervals.
4. Never use caustic agents to clean plastic parts.
CAUTION. Do not use cleaning agents to clean the plastic
parts of the saw. A mild detergent on a damp cloth is
recommended.
General inspection
Regularly check that all the fixing screws are tight. They
may vibrate loose over time.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing, replacing,
technical service or you simply need help or advice,
please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair or replacement is required,
you must provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|