1500W
MAGNESI
ROTARY H
WITH SDS-PLU
RHD1500
INSTRUCTION MANU
Code: RHD1500
Date: 061219
Black
Cyan
Magenta
Yellow
Edition: 05
Op: DCR
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of symbols
Introduction
The rating plate on your tool may show symbols. These
represent important information about the product or
instructions on its use.
Your new GMC power tool will more than satisfy your
expectations. It has been manufactured under stringent
GMC Quality Standards to meet superior performance
criteria.
You will find your new tool easy and safe to operate,
and, with proper care, it will give you many years of
dependable service.
CAUTION. Carefully read through this entire Instruction
Manual before using your new GMC Power Tool. Take
special care to heed the Cautions and Warnings.
Your GMC power tool has many features that will make
your job faster and easier. Safety, performance, and
dependability have been given top priority in the
development of this tool, making it easy to maintain
and operate.
Wear hearing protection.
Wear eye protection.
Wear breathing protection.
Double insulated
for additional protection.
Conforms to relevant standards for
electromagnetic compatibility.
Specifications
Voltage:
Power input:
No load speed:
Chuck type:
230–240V ~ 50 Hz
1500W
0 – 780 min-1
Environmental protection
SDS
Recycle unwanted materials instead of
disposing of them as waste. All tools, hoses
and packaging should be sorted, taken to
the local recycling centre and disposed of
in an environmentally safe way.
Keyed chuck capacity:
Impact frequency:
Impact energy:
Drilling capacity:
Wood:
1.5 – 13mm
0 – 2700 BPM
5.5 J
40mm
13mm
36mm
Steel:
Masonry:
Tool weight:
5.5kg
The sound intensity level for the operator may exceed
85dB(A) and sound protection measures are necessary
3
Download from Www.Somanuals.com. All Manuals Search And Download.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
General safety rules
WARNING. Read all instructions. Failure to follow all
instructions listed below may result in electric shock,
fire and/or serious injury. The term “power tool” in
all of the warnings listed below refers to your mains
operated (corded) power tool or battery operated
(cordless) power tool.
3. Personal safety
a. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or under
the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
Save these instructions
1. Work area
a. Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b. Do not operate power tools in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
b. Use safety equipment. Always wear eye protection.
Safety equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Avoid accidental starting. Ensure the switch is in the
off position before plugging in. Carrying power tools
with your finger on the switch or plugging in power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached
to a rotating part of the power tool may result in
personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool
in unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
2. Electrical safety
a. Power tool plugs must match the outlet.
Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce
risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of these devices can
reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it
was designed.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
c. Disconnect the plug from the power source before
making any adjustments, changing accessories, or
storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
Additional safety rules for drills
Wear ear protectors with hammer drills.
Exposure to noise can cause hearing loss.
Use auxiliary handles supplied with the tool.
Loss of control can cause personal injury.
• Fully unwind cable drum extensions to avoid potential
overheating.
• When an extension cable is required, you must ensure
that it has the right ampere rating for your power tool
and is in safe electrical condition.
• If possible, always use clamps or a vice to hold
your work.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
• Always switch off before you put the drill down.
• Ensure that the lighting is adequate.
• Do not put pressure on the drill, such that it slows the
motor down. Allow the drill bit to cut without pressure.
You will get better results and you will be taking better
care of your tool.
• Keep the area free of tripping hazards.
• Do not let anyone under 18 years operate this tool.
• Only use accessory bits in good condition.
• Before drilling, check that there is sufficient clearance
for the drill bit under the work piece.
• Do not touch the bit after operation. It will be very hot.
• Keep your hands away from under the work piece.
• Never use your hands to remove sawdust, chips or waste
close by the bit.
• Rags, cloths, cord, string and the like should never be
left around the work area.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from those intended could result in
a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Support the work properly.
• If you are interrupted when operating the drill, complete
the process and switch off before looking up.
• Periodically check that all nuts, bolts and other fixings
are properly tightened.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
• When using the drill, use safety equipment including
safety glasses or shield, ear defenders, and protective
clothing including safety gloves. Wear a dust mask if
the drilling operation creates dust.
WARNING. Before connecting a tool to a power source
(mains socket power point receptacle, outlet, etc.) be sure
that the voltage supply is the same as that specified on
the nameplate of the tool. A power source with a voltage
greater than that specified for the tool can result in
serious injury to the user, as well as damage to the tool.
If in doubt, do not plug in the tool. Using a power source
with a voltage less than the nameplate rating is harmful
to the motor.
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
• Damage to the lungs if an effective dust mask is not worn.
• Damage to hearing if effective ear defenders are not worn.
Wear goggles
Wear earmuffs
Wear a breathing mask
The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual will
be considered a case of misuse. The user and not the
manufacturer shall be liable for any damage or injury
resulting from such cases of misuse.
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Even when the tool is used as prescribed it is not possible
to eliminate all residual risk factors. The following hazards
may arise in connection with the tool’s construction and
design:
To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operating
instructions to be found in this Manual. All persons who
use and service the machine have to be acquainted with
this Manual and must be informed about its potential
hazards. Children and frail people must not use this
tool. Children should be supervised at all times if they
are in the area in which the tool is being used. It is
also imperative that you observe the accident prevention
regulations in force in your area. The same applies for
general rules of occupational health and safety.
The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
Even when the tool is used as prescribed it is not
possible to eliminate all residual risk factors. The
following hazards may arise in connection with the tool’s
construction and design:
• Damage to the lungs if an effective dust mask is
not worn.
• Damage to hearing if effective earmuffs are not worn.
Additional safety rules for rotary hammers
• Do not use the rotary hammer in damp or wet areas.
• Do not attempt to use the rotary hammer for a purpose
on which it was not designed. The rotary hammer will
give much better service if you do not use excessive
force. Excessive force will overheat the rotary hammer
and damage internal parts. Excessive force may cause
you to over balance causing damage and/or injury.
• Be prepared for the initial torque reaction of the drill.
• Chisel bits and drill bits may be thrown out of the
machine accidentally and cause serious injury. Before
starting to work always check that the chisel or drill bit
is properly locked in the chuck.
• Examine the chuck regularly for signs of wear or
damage. Never start up a rotary hammer tool until it is
pressed against a work piece(bracket, wall, ceiling, etc).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
• Wear work gloves to protect fingers from bruising
and abrasions.
• Always check walls and ceilings for position of hidden
power cables, pipes etc. A metal detector can be
obtained from any good DIY store for this purpose.
• Wear ear protectors. Exposure to noise can cause
hearing loss.
• Use auxiliary handles supplied with the tool. Loss of
control can cause personal injury.
Contents of carton
The Rotary Hammer Drill is supplied with the following
accessories:
• Depth gauge rod
• Auxiliary handle
• SDS Drill bits:
8mm x 150mm
10mm x 150mm
12mm x 150mm
• SDS Chisel bits
Point chisel 14mm x 250mm
Flat chisel 14mm x 250mm
• 13mm Keyed chuck with SDS-Plus chuck adaptor
• 13mm Keyed chuck key
• Spanner
• Grease pot
• Spare set of brushes
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Know your product
1. Dust shield
2. Locking sleeve
3. Wing nut
4. Selector knob
9
3
4
5
18
6
5. Gearbox cover
6. Trigger switch
7. Hammer function switch
8. Auxiliary handle
9. Depth gauge
10. SDS Drill bits (x 3)
11. SDS Chisel bits (x2)
12. 13mm Keyed chuck key
13. 13mm Keyed chuck
14. Pin wrench
1
7
2
15. Dust cap
16. Gearbox grease pot
17. SDS-Plus chuck adaptor
18. Variable speed dial
8
14
17
10
10
10
11
16
15
13
11
12
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Unpacking
Using the dust protector cap
Due to modern mass production techniques, it is unlikely that
your GMC Power Tool is faulty or that a part is missing. If you
find anything wrong, do not operate the tool until the parts
have been replaced or the fault has been rectified. Failure to
do so could result in serious personal injury.
The dust cap (15) can be used
to give added protection against
dust and debris entering the SDS
chuck.
1. Place the cap over the shank
of the bit and slide it forward
until it rests against the
shoulder of the bit.
Inserting SDS bits
WARNING. Always ensure that the drill is switched off
and plug is removed from the power point before making
any adjustments.
1. Apply a coating of universal
grease to the end of the bit
that is to be inserted into the
SDS chuck.
2. Insert the bit into the SDS
chuck as normal.
Selecting the required function
It is possible to use the Rotary Hammer Drill in three
different modes:
2. Pull back the locking sleeve (2),
insert the SDS Plus bit into the
chuck opening and release the
locking sleeve (2).
1. Rotation only – for drilling into metal and wood products.
2. Rotary hammer – for drilling into brick, concrete and
masonry products.
3. Hammer only – for chiseling brick, concrete and masonry
products.
Note. The SDS Plus bit needs to be
inserted in a specific way to ensure
it locks into the chuck. To check if
it is properly inserted, attempt to
pull the bit out of the chuck. If it
can be removed without pulling
back locking sleeve (2), rotate the
bit a little and re-insert it until the
bit locks firmly into place.
To select the required mode of operation set the selector
knob (4) and the hammer function switch (7) to the
positions indicated.
Note. To operate the selector knob (4), first push the
button on the knob then turn it either to the
the position as required.
or to
Auxiliary handle
1. Loosen wing nut (3) anti-
clockwise to loosen the collar
and slip it over the chuck onto
the drill.
2. Adjust the position of the handle
to suit the application and add
the depth gauge (9) if required.
The hammer function switch (7) can be turned to the
left or to the right as required.
3. Place the tip of the drill on the
workpiece and push in the depth gauge until the desired
hole depth is indicated on the depth gauge scale. Tighten
wing nut (3).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Rotation only mode of operation
Setting the speed
The variable speed dial (18)
allows you to change the
operating speed of the tool.
Set the selector knob (4) to the
position and the
hammer function switch (7) to the right position.
Rotary hammer mode of operation
It is used to set the speed of
drilling to suit different materials
and applications.
Set the selector knob (4) to the
hammer function switch (7) to the left
position and the
position.
Hammer only mode of operation
Set the selector knob (4) to the position and the hammer
function switch (7) to the left
Use your finger or thumb to turn
the dial forwards to decrease
the speed and and backwards to
increase the speed.
position.
Fitting a keyed chuck
WARNING. Always ensure that
the drill is switched off and plug
is removed from the power point
before making any adjustments.
The keyed chuck (13) can be
fitted to the SDS chuck with the
use of the in-built SDS chuck
adaptor (17). The keyed chuck
allows bits with a straight shank
to be used with the tool.
Switching on and off
Connect the plug to the power
point.
Press the trigger switch (6) to
start the drill and release the
trigger when you wish to stop.
Operation
Hold the drill with your two upper
fingers comfortably on the trigger
switch.
Use the auxiliary handle (8) where
possible to gain extra control and
to prevent fatigue.
1. Grip and pull back the locking
sleeve (2) and insert the SDS
chuck adaptor (17).
2. It may be necessary to turn
the SDS chuck adaptor in
order for it to locate properly.
Replacing worn carbon brushes
Take your product to the nearest authorised service centre
for brush replacement.
3. Release the locking sleeve (2)
to lock the adaptor in place.
Ensure the chuck is secure.
Never attempt to maintain or repair any electrical equipment
yourself. Only have this done by an authorised service centre.
WARNING. The keyed chuck (13) is only to be used when
drilling into wood and metal. It must not be used in the
hammer mode of operation.
Gearbox maintenance
Carry out the following procedure
after each period of approximately
6 hours of use.
1. Use wrench (14) to unscrew the
gearbox cover (5) located on
top of the drill.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Use a spatula or similar instrument to apply the grease
into the gearbox cavity. Be careful not to scratch or
otherwise damage the mechanism.
Power cord maintenance
If the supply cord needs replacing, the task must be
carried out by the manufacturer, the manufacturer’s
agent, or an authorised service centre in order to avoid
a safety hazard.
3. Replace the cover.
CAUTION. Do not over-tighten
the cover (5) or overfill the
gearbox with grease. If you run
out of grease, or are not sure
how to change the grease, please
take your product to the nearest
authorised service centre and
have a qualified person replace
the grease.
Cleaning
1.Keep your machine and its cord clean. The outside of
the machine can be cleaned using a damp soft cloth
with a mild detergent if required.
2.Some maintenance products and solvents may damage
the plastic parts; these include products containing
benzene, trichloroethylene, chloride and ammonia.
3.Excessive sparking generally indicates the presence
of dirt in the motor or abnormal wear on the carbon
brushes.
4.Take special care to keep the ventilation inlets/outlets
free from obstruction; cleaning with a soft brush will
usually be sufficient to ensure acceptable internal
cleanliness.
5.Wear eye protection when carrying out cleaning.
CAUTION. Do not use cleaning agents to clean the plastic
parts of the drill.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
GMC customer assist
If your product needs repairing, replacing,
technical service or you simply need help or advice,
please contact us on our Customer Assist Line
1300 880 001 (Australia) or 0800 445 721 (New Zealand).
For prompt service we suggest you log your service request
access to the Internet, please contact our service department
on 1300 880 001 (Australia) or 0800 445 721 (New Zealand).
7am –7pm, 7days a week (AEST).
Please note that if repair or replacement is required,
you must provide a valid original purchase receipt.
You will need the following details at hand to log your service request;
Personal details: First & Last name, address, pick up address,
contact phone numbers, email address
Product details: Product number, date of purchase, retailer bought from,
State & postcode, receipt number, reason for the request,
copy of official purchase receipt
Attach your purchase receipt and save with this Manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
|