GE Monogram Refrigerator ZIS42N User Manual

GE Monogram^®

42" Built-In Refrigerators

Custom

Options Guide

and

Installation

Instructions

With Custom Panel Dimensions

and Trim Kit

Installation Instructions

Models:

ZIS42N

These Monogram built-in refrigerators are

designed to be customized with decorator

door and grille panels. Field installed

panels are required.

Factory installed trim will accommodate

1/ 4" thick custom panels or optional

Lexan^®and Stainless Steel panel kits.

Optional trim kits allow an even broader

range of custom appearance options.

ZISW42D

ZISB42D

Read this booklet carefully to accomplish the

desired appearance and to insure a trouble free

installation.

This booklet contains information and

illustrations to demonstrate custom

possibilities. Custom door and grille panel

sizes vary to accommodate the kit being

used. Dimensions for each application are

included and can be faxed or sent to the

cabinet manufacturer so that the panels can

be constructed accurately.

Download from Www.Somanuals.com. All Manuals Search And Download.

Design Information

42" Built-In Refrigerator

Ad va n c e P la n n in g

Flu s h o r

S e m i-Flu s h

En c lo s u re

In s t a lla t io n s

3/4"

True Flush Installation

In a flush installation,

Semi-Flush Installation

These refrigerators

the refrigerator doors

can also be installed

will align evenly with the

front face of adjacent cabinet

doors. The refrigerator blends

into the surrounding cabinetry.

semi-flush into an enclosure

using the minimum cutout

width. The case trim creates a

frame around the opening.

Side Panel Requirements:

Monogram built-in refrigerators can be installed flush

with typical 24-3/4" deep cabinetry.

• Side panels are not required whenever the

refrigerator is installed into an enclosure or between

pantry and oven cabinets.

• Side panels are required whenever the sides of the

refrigerator are exposed.

When installed semi-flush, the case trim will conceal

slight gaps around the enclosure. The refrigerator will

project forward approximately 3/4" beyond the front

face of surrounding cabinetry.

• Side panel sizes vary depending on the type of

installation being made.

In any installation situation, a wide range of appear-

ance options can be accomplished through the use of

one or more trim kits. See trim kit descriptions and

appearance options on page 5.

To accomplish an attractive installation, you must:

1. Determine the need for side panels.

2. Determine side panel thickness.

3. Order matching side panels from the cabinet

manufacturer. Be sure to provide the exact

dimensions.

En c lo s u re

Cu t o u t a n d

P ro d u c t

*Finished Width

Wall View

• To achieve a flush fit the finished cutout width must

be at least 42" wide.

• A semi-flush installation requires 41-1/2" min. finished

cutout width.

• The electrical and water locations must be located as

shown for either type of installation.

Dim e n s io n s

Electrical

Area

18 3/8"

24 3/4" Total

Depth

84 1/2" max

83-1/4" min

Finished

74" From Floor

toBottom

of Electrical

Opening

83" Min

84-1/2" Max

Water Supply

3 1/2"

42"

*42" Min. for a flush installation

41-1/2" Min. for a semi-flush installation

24-3/4"

Note: Additional cutout width may be required when

side panels are used. Add side panel thickness to the

finished cutout to calculate rough-in width. See

installation examples on the following page.

Download from Www.Somanuals.com. All Manuals Search And Download.

Design Information

42" Built-In Refrigerators

In s t a lla t io n Exa m p le s

Side panels are required whenever the sides of the refrigera-

Therefore, the rough-in dimensions must allow for side panel

thickness. In both a flush and semi-flush installation, the

finished dimension, (the width of the opening after side panels

are installed), must accommodate the full width of the

refrigerator.

tor will be exposed.

1/2" to 3/4" side panels are normally set into place and

fastened to adjacent cabinetry or to the back wall before

rolling the refrigerator into the opening.

See page 14 for side panel sizes.

Flush and Semi-Flush

In s t a lla t io n

Be t w e e n

Ba s e &

Installations

Refrigerator

Cabinet

Wa ll Ca b in e t s

1/4" Thick

Side Panels

Finished Dim.

Roughed-In Dim.

41-1/2"

42"

Refrigerator door

Note: 1/4" thick side panels can be

Cabinet

inserted into the case trim, making the

rough-in the same as the outside trim

width, 42".

1/4" Side Panels. Insert end of

side panel into trim

Flush and Semi-Flush

Installations

In s t a lla t io n

At En d -o f-Ru n

1/2" Thick

Side Panels

Refrigerator

Cabinet

42"

43"

Finished Dim.

Rough-In Dim.

Refrigerator door

Note: 1/2" thick side panels shown. Side panels can

be any thickness. Add side panel thickness to outside

trim width (42") to calculate the rough-in dimension.

The leading (front) edge must be finished to match

surrounding cabinetry.

Cabinet

1/2" To 3/4" Side Panels. Leading

Edge Flush With Cabinet

Fra m e le s s

Ca b in e t s

Side panels, 1/2" minimum thickness are

required when using frameless cabinets.

The side panel acts as a spacer between the

cabinet and the case trim and prevents

interference with cabinet door swing. The

leading (front) edge must be finished to

match surrounding cabinetry.

1/2" To 3/4" Side Panels. Leading

Edge Flush With Cabinet

Refrigerator

Cabinet

Refrigerator door

Ac c e s s o ry

P a n e l Kit s

Field installed door and grille panels are required. The factory

installed trim will accept accessory panel kits. White or black

Lexan^®and stainless steel kits are available. Panels are cut to

size and ready to install. These panel kits must be ordered

separately.

A wide range of custom appearance options can be created

with optional custom trim kits. See the opposite page for

examples and trim kit descriptions.

Model

Black

White

Stainless

ZWSP42

ZIS42N

ZISW42D

ZISB42D

ZWBP42

ZWWP42

ZWWP42D

ZWSP42D

ZWBP42D

Download from Www.Somanuals.com. All Manuals Search And Download.

Design Information

42" Built-In Refrigerator

Ad va n c e

p la n n in g

e xt e rio r

a p p e a ra n c e

o p t io n s

These refrigerators are designed to be customized with

decorator door and grille panels. Field installed custom

door and grille panels are required.

You should:

1. Select the appearance option.

2. Order the trim kit(s) for that option.

3. Order the custom door and grille panels from the

cabinet manufacturer. The exact dimension for each

trim kit application is provided in this booklet. Find

and pull out the page for your application and fax or

send it to the cabinet manufacturer. The cabinet

manufacturer must have this information to con-

struct the panels accurately.

Factory installed trim accommodates 1/4" thick custom

panels, Lexan^®or stainless steel panel kits.

Appearance options are accomplished through the

use of one or more trim kits. Kits must be ordered

separately.

Door and grille panel sizes vary to accommodate the kit

being used. Sizes are provided in this booklet.

4. Determine the final installation situation and order

matching side panels.

3/4" thick custom panels–Without trim kits

A raised panel design, screwed or glued to a 1/4" thick

backing can be used. See pages 7 and 11 for panel

sizes and clearances.

Important: Maximum weight for fresh food panels is

50 pounds and 30 pounds for freezer door panels.

Ap p e a ra n c e

Exa m p le s

Trim k it

De s c rip t io n s

1/4" Custom panels with

custom handles. Trim Kit

ZKH1.

1/4" and 3/4" panels with

standard handles. No trim

kits required.

1/4" Custom panels with

Tubular Stainless Steel

handles. Trim Kit ZKHSS1.

3/4" Custom panels with

Tubular Stainless Steel

handles and custom

dispenser collar. Trim

Kits ZKHTSS1, ZKT42 &

ZWCD1.

3/4" Custom panels with

custom handles. Trim kits

ZKT42 & ZKHT1.

Door Handle Options

Dispenser Options

ZKH1 – Provides the necessary framework to install

custom handles, of your choice, onto 1/4" thick panels.

(Handles not included.)

ZWCD1 – Provides for the installation of a custom

collar trim on the dispenser and for one continuous

custom panel on the freezer door. This kit can be used

alone, or with all other kits.

ZKHSS1 – Tubular stainless steel handles for 1/4" thick

panel installations.

Toekick Option

ZWT1 – White toekick (supplied toekick is black).

Includes a white toekick to fit 36", 42", 48" side-by-side

models and 36" bottom mount and single door models.

ZKHT1 – Provides the necessary framework to install

custom handles, of your choice, onto 3/4" thick panels.

(Handles not included.) This kit must be used in

combination with ZKT42.

Grille Panel Options

ZG2 – Provides 1/4" grille panel frame side pieces for

83", 83-1/2" and 84-1/2" installation heights. The supplied

grille panel frame is factory set for 84".

ZKHTSS1 – Tubular stainless steel handles for 3/4" thick

panel installations. This kit must be used in combination

with ZKT42.

Note: ZG1 Grille Panel Kit is available for models

produced before January 1997. Panel sizes for

ZG1 and ZG2 are the same. The ZG1 kit can be

ordered from your Monogram dealer.

Custom Panel Options

ZKT42 – Provides for the installation of 3/4" thick

trimless custom door and grille panels with the

standard (supplied) full length handle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Front View

(not to scale)

ZIS 4 2 N

(No n -d is p e n s e r)

Side View

(not to scale)

41" Case Width

24 3/4"

De s ig n In fo rm a t io n

42" Overall Width

Cutout dimensions, clearances and side panel sizes are

determined by the many installation options available.

Side panels must be used whenever the sides of the

refrigerator will be exposed. Side panels are not required

when refrigerator is installed into an enclosure or

between pantry and oven cabinets. IMPORTANT–Side

panels, 1/2" minimum thickness, are required when using

FRAMELESS CABINETS.

12 1/4" max

10-3/4" min

84 1/2" max

83" min

• Field installed custom panels, Lexan or stainless steel

panels are required. The door panels and grille panel

sizes vary to accommodate the kit being used.

• A custom toekick can be installed to match or comple-

ment the surrounding cabinetry. Use the supplied

toekick as a template to cut out notches around hinges

and water lines.

72 1/4"

Op t io n a l Kit s :

• ZWBP42: Black Lexan Panel Kit (no trim kit required).

• ZWWP42: White Lexan Panel Kit (no trim kit required).

• ZWSP42: Stainless Steel Panel Kit (no trim kit required).

• ZKH1: For installation of a custom handle on 1/4" panels.

• ZKT42: For installation of 3/4" custom panels.

• ZKHT1: For installation of a custom handle on 3/4"

panels. (This kit must be used in combination with

ZKT42.)

• ZKHSS1: Tubular Stainless Steel handles on 1/4" panels.

• ZKHTSS1: Tubular Stainless Steel handles on 3/4"

panels. (This kit must be used in combination with

ZKT42.)

*Finished Width

Wall View

(not to Scale)

• ZG2: 1/4" grille panel frame side pieces for 83", 83-1/2"

and 84-1/2" installation heights. Factory set height is 84".

• ZWT1: White toekick (supplied toekick is black).

Includes a white toekick to fit 36", 42", 48" side-by-side

models and 36" bottom mount and single door models.

Locate Grounded

Electrical outlet

Within Solid

18 3/8"

Area Above

84 1/2" max

83-1/4" min

Finished

74" From

Floor to

Ad d it io n a l S p e c ific a t io n s

• A 115 volt 60 Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or

circuit breaker is recommended. Install a properly

grounded 3-prong electrical receptacle recessed into

the back wall. Electrical must be located on rear wall.

• Water line can enter opening through the floor or back

wall. The water line should be 1/4" O.D. copper tubing

between the cold water line and water connection

location, long enough to extend to the front of the

refrigerator. Installation of an easily accessible shut off

valve in the water line is recommended.

Bottom of

Electrical Area

Opening

Locate Water

Supply Within

the Shaded

Area Below

3 1/2"

Cle a ra n c e s

If the refrigerator is to be installed in a corner:

• A 4" min. clearance between the case trim and

adjacent wall on both sides of the refrigerator will

assure a 90° door opening and access to all drawers. A

10" clearance is required on both sides for removal

of pans.

*42" Min. for a flush installation into an enclosure.

*41-1/2" Min. for a sem i-flush installation into an enclosure.

Note: Additional cutout width m ay be required when side panels are

used. Add side panel thickness to the finished cutout to calculate

rough-in width. See installation exam ples on page 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions Using Standard Trim

1/4" thick panels

ZIS 4 2 N (n o n -d is p e n s e r)

S t a n d a rd Trim w it h 1 /4 " P a n e ls

• 1/4" Panels: Cut panels to size.

• Custom handles with 1/4" door panels require Trim Kit

ZKH1 (or ZKHSS1 for tubular-stainless steel handles).

Panels secured to 1/4" thick backing

Freezer Panel

Fresh Food Panel

S t a n d a rd Trim w it h P a n e ls s e c u re d t o

1 /4 " t h ic k b a c k in g

• Applying a raised panel design to a 1/4" thick backing

(screwed or glued): Cut 1/4" panels to size, fabricate the

raised panel to permit clearances of at least 2" from the

handle side for fingertip clearance of the standard

handle, 1-1/4" from the hinge side to avoid striking

adjacent cabinetry and 5/16" from the top and bottom

edges to allow for the trim flange then install.

• Countertops adjacent to refrigerator installation should

be mitered 45° degrees.

67 7/8"

No t e : ZKHT1 custom handle kit cannot be used in this

configuration.

Custom Grille Panel

41"

15 1/4"

25 1/4"

Important: Maximum weight for fresh food panels is

50 pounds and 30 pounds for freezer door panels.

1/4" Thick Panel

The grille panel frame is factory assembled

for 84" installation height. If installation height

varies, order ZG2 trim kit which provides

optional side trim pieces. Cut grille panel to

sizes shown below.

Raised Panel on 1/4" Thick Backing

Using Standard Handles

1/4"

Thick

Backing

Appearance

Panel

Installation Height

83"

Panel Height

83-1/2"

8-1/2"

84-1/2"

9-1/2"

1 1/4"

Clearance

hinge side

2" Clearance

handle side

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of panel frame.

Case Trim

Door

Handle

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions

Using Trim Kit ZKT42

3/4" thick panel with standard handle

ZIS 4 2 N (n o n -d is p e n s e r)

• The ZKT42 trim kit provides for the installation of 3/4"

custom door and grille panels, using the standard full-

length handle. Cut panels to size and install.

Freezer Panel

Fresh Food Panel

67 15/16"

15 1/16"

25 1/16"

Important: Maximum weight for fresh food panels is

50 pounds and 30 pounds for freezer door panels.

Custom Grille Panel

41 1/2"

Over 1/4" Thick (3/4" max) Panel

Grille Panel height can vary to fill installation

height.

Installation Height

Dimension A

8-1/4"

83"

83-1/2"

84"

8-3/4"

9-1/4"

84-1/2"

9-3/4"

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of grille panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions

Using Trim Kits ZKT42

3/4" thick panel

ZIS 4 2 N (n o n -d is p e n s e r)

• ZKT42 and ZKHT1 installed together provides for the

installation of 3/4" custom door and grille panels,

using a custom handle, of your choice. Order

ZKHTSS1 for tubular stainless-steel handles. Cut

panels to size, rout the handle side of the panels as

shown below and install.

with custom handle

Fresh Food Panel

Freezer Panel

Important: Maximum weight for fresh food panels

is 50 pounds and 30 pounds for freezer door panels.

67 15/16"

15 5/16"

25 5/16"

Rout panels to specification below on

the handle side of each panel

1 13/16"

1/4"

max

Fresh Food Door Face

Freezer Door Face

Custom Grille Panel

41 1/2"

Over 1/4" Thick (3/4" max) Panel

Grille Panel height can vary to fill installation

height.

Installation Height

Dimension A

8-1/4"

83"

83-1/2"

84"

8-3/4"

9-1/4"

84-1/2"

9-3/4"

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of grille panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

ZIS W4 2 D (w h it e d is p e n s e r)

ZIS B4 2 D (b la c k d is p e n s e r)

Front View

(not to scale)

Side View

(not to scale)

De s ig n In fo rm a t io n

41" Case Width

Cutout dimensions, clearances and side panel sizes are

determined by the many installation options available. Side

panels must be used whenever the sides of the refrigerator

will be exposed. Side panels are not required when

refrigerator is installed into an enclosure or between pantry

and oven cabinets. IMPORTANT–Side panels, 1/2" min.

thick, are required for FRAMELESS CABINETS.

24 3/4"

42" Overall Width

12 1/4" max

10-3/4" min

• Field installed custom panels, Lexan or stainless steel

panels are required. Custom door panels and grille panel

sizes vary to accommodate the kit being used.

• A custom toekick can be installed to match or comple-

ment the surrounding cabinetry. Use supplied toekick as

a template to cut notches for hinges and water lines.

84 1/2" max

83" min

72 1/4"

Op t io n a l Kit s :

• ZWBP42D: Black Lexan Panel Kit (no trim kit required).

• ZWWP42D: White Lexan Panel Kit (no trim kit required).

• ZWSP42D: Stainless Steel Panel Kit (no trim kit required).

• ZKH1: For installation of custom handles on 1/4" panels.

• ZKT42: For installation of 3/4" custom panels.

• ZKHT1: For installation of custom handles on 3/4" panels.

(This kit must be used in combination with ZKT42.)

• ZWCD1: For installation of a custom collar trim on the

dispenser for one continuous custom panel

on the freezer door.

*Finished Width

• ZKHSS1: Tubular Stainless Steel handles on 1/4" panels.

• ZKHTSS1: Tubular Stainless Steel handles on 3/4" panels.

(This kit must be used in combination with ZKT42.)

• ZG2: 1/4" grille panel frame side pieces for 83", 83-1/2" and

84-1/2" installation heights. Factory set height is 84".

• ZWT1: White toekick (supplied toekick is black). Includes

a white toekick to fit 36", 42", 48" side-by-side models and

36" bottom mount and single door models.

Wall View

(not to Scale)

Locate Grounded

Electrical outlet

Within Solid

18 3/8"

Area Above

84 1/2" max

83-1/4" min

Finished

74" From

Floor to

Bottom of

Electrical Area

Ad d it io n a l S p e c ific a t io n s

• A 115 volt 60 Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit

breaker is recommended. Install a properly grounded

3-prong electrical receptacle recessed into the back wall.

Electrical must be located on rear wall.

• Water line can enter opening through the floor or back

wall. The water line should be 1/4" O.D. copper tubing

between the cold water line and water connection

location, long enough to extend to the front of the

refrigerator. Installation of an easily accessible shut off

valve in the water line is recommended.

Opening

Locate Water

Supply Within

the Shaded

Area Below

3 1/2"

Cle a ra n c e s

*42" Min. for a flush installation into an enclosure.

If the refrigerator is to be installed in a corner:

• A 4" min. clearance between the case trim and adjacent

wall on both sides of the refrigerator will assure a 90°

door opening and access to all drawers. A 10" clearance

is required on both sides for removal of pans.

*41-1/2" Min. for a sem i-flush installation into an enclosure.

Note: Additional cutout width m ay be required when side panels are

used. Add side panel thickness to the finished cutout to calculate

rough-in width. See installation exam ples on page 4.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions Using Standard Trim

1/4" thick panels

ZIS W4 2 D (w h it e d is p e n s e r)

ZIS B4 2 D (b la c k d is p e n s e r)

S t a n d a rd Trim w it h 1 /4 " P a n e ls

• 1/4" Panels: Cut panels to size.

Panels secured to 1/4" thick backing

• Custom handles with 1/4" door panels require Trim Kit

ZKH1. When using ZKH1 with the standard dispenser

trim, the length of the custom handle, top to bottom

cannot exceed 11-3/4".

• Tubular stainless steel handle kit, ZKHSS1.

• Custom collar dispenser trim with 1/4" door panels

require trim kit ZWCD1.

Freezer Panel Freezer Panel

Standard

Custom

Fresh Food

Panel

Dispenser

17 11/16"

16 5/8"

S t a n d a rd Trim w it h P a n e ls s e c u re d t o

1 /4 " t h ic k b a c k in g

67 7/8"

2 9/16"

• Applying a raised panel design to a 1/4" thick backing

(screwed or glued): Cut 1/4" panels to size, fabricate

the raised panel to permit clearances of at least 2"

from the handle side for fingertip clearance of the

standard handle, 1-1/4" from the hinge side to avoid

striking adjacent cabinetry and 5/16" from the top and

bottom edges to allow for the trim flange, then install.

• Countertops adjacent to refrigerator installation

should be mitered 45° degrees.

36 7/8"

No t e : ZWCD1 custom collar dispenser trim and

ZKHT1 custom handle kits cannot be used in this

configuration.

15 1/4

15 1/4"

25 1/4"

Important: Maximum weight for fresh food panels

is 50 pounds and 30 pounds for freezer door panels.

Custom Grille Panel

41"

1/4" Thick Panel

Raised Panel on 1/4" Thick Backing

Using Standard Handles

The grille panel frame is factory assembled

for 84" installation height. If installation height

varies, order ZG2 trim kit for optional side trim

pieces. Cut grille panel to sizes shown below.

1/4"

Thick

Backing

Appearance

Panel

Installation Height

83"

Panel Height

1 1/4"

Clearance

hinge side

83-1/2"

8-1/2"

2" Clearance

handle side

84-1/2"

9-1/2"

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of panel frame.

Case Trim

Custom Dispenser Cutout

9 7/16"

12 5/16"

Door

Handle

The Cutout is 9 7/16" wide

by 12 5/16" high.

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions

Using Trim Kit ZKT42

ZIS W4 2 D (w h it e d is p e n s e r)

ZIS B4 2 D (b la c k d is p e n s e r)

3/4" thick panel with standard handle

and/or ZWCD1 custom collar trim

• The ZKT42 trim kit provides for the installation of 3/4"

custom door and grille panels, using the standard full-

length handle. Cut panels to size and install.

• For standard dispenser trim: Cut panels to size, rout the

bottom of the upper freezer panel and the top of the

lower freezer panel to allow placement of support

brackets and install (see detail A).

Freezer Panel Freezer Panel

Standard

Custom

Fresh Food

Panel

Dispenser

• For custom dispenser trim ZWCD1 kit must be used: Cut

panels to size, refer to detail B for dispenser cutout

routing instructions and install. When a raised panel

design is used, a custom middle rail is required. A

14-1/2" wide middle rail must be used because the

custom collar trim must be located within the raised

portion of the panel. This area must be 3/4" thick. See

detail C for raised panel design requirements.

17 11/16"

16 11/16"

67 15/16"

2 5/16"

Custom Grille Panel

41 1/2"

37"

Over 1/4" Thick (3/4" max) Panel

15-1/16"

15 1/16"

25 1/16"

Grille Panel height can vary to fill installation

height.

Important: Maximum weight for fresh food panels is

50 pounds and 30 pounds for freezer door panels.

Installation Height

Dimension A

8-1/4"

83"

83-1/2"

84"

Detail A

8-3/4"

Upper

Freezer

Panel

9-1/4"

Detail B Custom

Dispenser Cutout

84-1/2"

9-3/4"

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of grille panel.

3/32"

9 7/16"

7/8"

Detail C

Raised Panel Design

Wide

12 5/16"

Rout

*2-3/16" Stiles

Right Side

*3" Stiles

Left Side

Panel

Face

The Cutout is 9 7/16" wide

by 12 5/16" high. 3/4" panels

must be routed on all four

sides of the cutout. Rout

the back side of the panel

1/4" deep. 7/8" wide

Hole is Cut

After Door

Fabrication

Lower

Freezer

Panel

(shaded area).

14 1/2"

Wide

Middle

Rail

Handle

Side

*Custom Stiles and

Middle Rail Required

Section AA

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions

Using Trim Kit ZKT42

ZIS W4 2 D (w h it e d is p e n s e r)

ZIS B4 2 D (b la c k d is p e n s e r)

3/4" thick panel with custom handle

and/or ZWCD1 custom collar trim

• ZKT42 and ZKHT1 installed together provides for the

installation of 3/4" custom door and grille panels, using

a custom handle of your choice. Cut panels to size, rout

the handle side of the panels as shown below and install

(see detail B).

• For ZKHTSS1 tubular stainless steel handle kit, cut panels

to size and rout the handle side of the panels as shown in

detail B.

Freezer Panel Freezer Panel

Standard

Dispenser

Custom

Dispenser

Fresh Food

Panel

• For standard dispenser trim: Cut panels to size, rout the

handle side of the panels as shown in detail B, rout the

bottom of the upper freezer panel and the top of the lower

freezer panel to allow placement of support brackets (see

detail A) and install.

• For custom dispenser trim ZWCD1 kit must be used: Cut

panels to size, refer to detail C for dispenser cutout

routing instructions. When a raised panel design is used,

a custom middle rail is required. A 14-1/2" wide middle rail

must be used because the custom collar trim must be

located within the raised portion of the panel. This area

must be 3/4" thick. See detail D for raised panel design

requirements.

16 11/16"

17 11/16"

67 15/16"

2 9/16"

37"

• When using the standard full-width dispenser trim, the

length of the custom handle, top to bottom cannot exceed

11-3/4". Locate the handle a minimum of 3/4" and a

maximum of 1-1/2" from the edge of the panel. There are

no length restrictions on handles for models using a

custom collar dispenser trim (ZWCD1).

15 5/16"

25 5/16"

Important: Maximum weight for fresh food panels is

50 pounds and 30 pounds for freezer door panels.

Custom Grille Panel

41 1/2"

Detail A

Upper

Freezer

Panel

Detail B

Rout panels to specification below on

the handle side of each panel

Over 1/4" Thick (3/4" max) Panel

1 13/16"

Grille Panel height can vary to fill installation

height.

3/32"

Installation Height

Dimension A

8-1/4"

83"

83-1/2"

84"

1/4"

max

8-3/4"

Fresh Food Door Face

Freezer Door Face

9-1/4"

Panel

Face

84-1/2"

9-3/4"

Detail C Custom

Dispenser Cutout

Important: Maintain 1-1/2" min. gap between

top of doors and bottom of grille panel.

Lower

Freezer

Panel

Detail D

Raised Panel Design

9 7/16"

*2-3/16" Stiles

Right Side

*3" Stiles

Left Side

7/8"

Hole is Cut

After Door

Fabrication

Wide

Rout

12 5/16"

14 1/2"

Wide

Middle

Rail

The Cutout is 9 7/16" wide

by 12 5/16" high. 3/4" panels

must be routed on all four

sides of the cutout. Rout

the back side of the panel

1/4" deep. 7/8" wide

Handle

Side

(shaded area).

*Custom Stiles and

Middle Rail Required

Section AA

Download from Www.Somanuals.com. All Manuals Search And Download.

Custom Panel Dimensions

42" Built-In Refrigerator

Fo r All Mo n o g ra m Bu ilt -In Re frig e ra t o rs

Side Panel or Filler Options

(not to scale)

Side panels m ust be used w henever the sides of the refrigerator

w ill be exposed.

1/ 2" to 3/ 4" Side Panels

24 3/4"

Leading Edge

23 9/16"

Flush w ith Cabinet

Front. The front or

leading edge, m ust be

finished to m atch

cabinetry

1/ 4" Side Panels

Insert end of

side panel into trim .

Top View

84"

Trim

3 3/4"

Standard 4" high toekick or trim to fit.

2 9/16"

Height m ay vary depending on application.

Standard 4" high toekick or trim to fit.

Height m ay vary depending on application.

23 5/16"

1/ 2" to 3/ 4" Side Panels

Recessed front edge.

Top View

84"

2 5/16"

Standard 4" high toekick or trim to fit.

Height m ay vary depending on application.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

• Tinsnips to cut banding

• Stepladder

• 1-1/2" open-end wrench

• Bucket

• Level

• Appliance Hand Truck

• Tubing cutter

• 7/16" open-end wrench

• Drill and appropriate

bits

• 7/16" socket with 3"

extension for ratchet

• Safety glasses

To o ls

Re q u ire d

• #2 Phillips screwdriver

• Stubby Phillips

screwdriver

Ha rd w a re

S u p p lie d

• Special velcro adhesive

strips for 1/4" side

panels

• 1/4-1/4 union with nuts

• 1/4" panel foam spacers

Ma t e ria ls

Re q u ire d

• Water shut-off valve (optional but recommended)

• Custom panels for fresh food, freezer compartments,

grille panel

• Side panels

• Hardware for side panel installation.

• 42" long 2x4 for Anti-Tip support

Flo o rin g

For proper installation, this refrigerator must be placed

on a level surface of hard material that is at the same

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the

height as the rest of the flooring. This surface should be refrigerator where you are working.

strong enough to support a fully loaded refrigerator.

Gro u n d in g

t h e

Re frig e ra t o r

IMPORTANT - (Please read carefully)

CAUTION

Attaching the adapter ground terminal to a wall

outlet cover screw does not ground the appliance

unless the cover screw is metal, and not insulated,

and the wall outlet is grounded through the house

wiring. You should have the circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE

PROPERLY GROUNDED.

The power cord of this appliance is equipped with a

three-prong (grounding) plug which mates with a

standard three-prong (grounding) wall receptacle to

minimize the possibility of electric shock hazard from

this appliance.

When disconnecting the power cord from the adapter,

always hold the adapter in place with one hand and

pulling the power cord with the other hand. If this is not

done, the adapter ground terminal is very likely to break

with repeated use.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

Should the adapter ground terminal break, DO NOT USE

the appliance until a proper ground has again been

established.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT

OR REMOVE THE THIRD

(GROUND) PRONG

Use of Extension Cords

Because of potential safety hazards under certain

conditions, we strongly recommend against the use of

an extension cord. However, if you still elect to use an

extension cord, it is absolutely necessary that it be a UL

listed 3-wire grounding type appliance extension cord

having a grounding type plug and outlet and that the

electrical rating of the cord be 15 amperes (minimum)

and 120 volts.

FROM THE POWER CORD.

Use of Adapter plug

Because of potential hazards under certain conditions,

we strongly recommend against use of an adapter plug.

However, if you still elect to use an adapter, where

local codes permit, a TEMPORARY CONNECTION, may

be made to a properly grounded 2-prong wall outlet by

use of a UL listed adapter available at most hardware

stores.

P RUDENCE

FICHE D’ADAPTATION

The larger slot in the adapter must be aligned with the

larger slot in the wall outlet to provide proper polarity in

the connection of the power cord.

(Fiches d’adaptation non permises au Canada)

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

S t e p 1

Re m o ve

P a c k a g in g

CAUTION

Refrigerator is much heavier at the top than at the

bottom – be careful when moving. When using a

hand truck, handle from side only.

P RUDENCE

Le réfrigérateur est beaucoup plus lourd en haut

qu'en bas. Il faut être prudent lors des

déplacements. Si un diable est utilisé, il faut

soulever le réfrigérateur sur le côté seulement.

• Remove outer carton.

– Carefully cut banding at the top and bottom.

• Slide out back corner posts (2).

• Slide carton off top of cabinet.

7/16" Bolt

NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN

IN ORDER TO REMOVE SKID!

• To remove skid, remove the four 7/16" bolts and their

brackets.

• There are support blocks on the bottom of the cabinet

and door. They must be removed before sliding unit

off the skid or damage will occur.

CAUTION

DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

• Carefully, tilt cabinet and slide blocks out from

beneath cabinet, slide unit off skid.

• Remove toekick from fresh food compartment and

set aside for later installation.

P RUDENCE

IL NE FAUT PAS ESSAYER DE FAIRE ROULER LE

RÉFRIGÉRATEUR POUR L'ENLEVER DE LAY PALETTE.

• A cold water supply is required for automatic icemaker

operation. The water pressure must be between 40 and

120 p.s.i.

• Route 1/4" OD copper tubing between house cold water

line and the water connection location.

S t e p 2

In s t a ll

Wa t e r Lin e

• Copper tubing should be long enough to extend to the

front of the refrigerator. Allow enough to accommodate

bend leading into the water valve.

Floor

Copper Tubing

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the line

of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

Washer

Saddle Type

Shutoff Valve

Inlet End

Pipe Clamp

Packing Nut

NOTE: It is best to install the valve into a vertical water

pipe. If you install the valve into a horizontal water pipe,

make the connection at the top or side, rather than at

the bottom, to avoid drawing off any sediment from the

water pipe.

Compression Nut

Outlet Valve

• Drill a 1/4" hole in the water pipe.

Ferrule

(Sleeve)

• Fasten the shut-off valve to the pipe with pipe clamp.

• Tighten the clamp screws until the sealing washer

begins to swell. Do not over tighten.

• Place a compression nut and ferrule (sleeve) onto the

end of the tubing and connect it to the shut-off valve.

Make sure the tubing is fully inserted into the valve and

ferrule is tightened.

NOTE: Saddle type shut-off valves are included in

many water supply kits. Before purchasing, make sure

a saddle type valve complies with your local plumbing

codes.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

• Turn on the main water supply and flush debris from

the line. Run about a quart of water through the tubing

into a bucket. Shut off water supply at the shut-off

valve.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

S t e p 2 A

WARNING

ATTENTION

Fo r In s t a lla t io n s

Wit h A Re ve rs e

Os m o s is S ys t e m

On ly

When connecting a GE Reverse

Osmosis Water System to your

refrigerator, the only approved

installation is with a GE RVKIT.

Lors du raccordement au réfrigérateur

du système GE de purification de l’eau

par osmose inversé seule l’installation

avec un ensemble GE RVKIT est

approuvée.

Rotate

Clockwise

To Remove

S k ip Th is

If the water supply to the refrigerator is

from a Reverse Osmosis Water System

AND the refrigerator also has a water

filter, use the refrigerator’s filter bypass

plug. Using the refrigerator’s water

filtration cartridge in conjunction with

the RO filter can result in hollow ice

cubes and slower water flow from the

water dispenser.

S t e p Wh e n

No t Us in g

RO S ys t e m

Si le réfrigérateur es alimenté en eau à

partir d’un système de filtration d’eau

par osmose inversée, et si le

réfrigérateur comporte également un

filtre à eau, utiliser le bouchon du

circuit de dérivation du filtre du

réfrigérateur. Si la cartouche de

filtration d”eau du réfrigérateur est

utilisée en conjonction avec le

système de filtration par osmose

inversée, on peut observer une

réduction du débit d’eau au point de

puisage, et la production de cubes de

glace creux.

Filter

Bypass

Plug

If you use the bypass Plug and want a light shield

without the filter opening, order a replacement solid

light shield WR02X8967.

S t e p 3

In s t a ll

S id e P a n e ls

• Side panels are not required when the refrigerator is

installed into an enclosure. Skip this step if you are

installing in an enclosure.

• Side panels are required whenever the sides of the

refrigerator will be exposed and when installed

between frameless cabinets. See pages 3 and 4.

• Side panel installation will be determined by the

design of the side panel you have previously chosen.

• Side panels must be installed plumb.

• If you choose to use 1/4" side panels, they should be

inserted into the case trim as illustrated. Fasten the

panels to the refrigerator with Velcro strips (provided)

before setting refrigerator in place. See illustration A.

• 1/2" to 3/4" side panels are normally set into place and

fastened to adjacent cabinetry or the back wall before

rolling the refrigerator into the opening. See illustra-

tions B and C.

Illustration A

Illustration B

Refrigerator

Cabinet

Refrigerator

Cabinet

Side

Panel

Refrigerator door

1/4" Side Panels – Insert End Of Side Panel Into Case Trim. Fasten

WIth Velcro Strips provided.

1/2" to 3/4" Side Panels – Leading Edge Of Side Panel Is Flush

With Cabinet front. Fasten To The Back Wall Using A Cleat.

Illustration C

Refrigerator

Cabinet

Refrigerator door

Cabinet

1/2" to 3/4" Side Panels – Recessed Front Edge of Side Panel.

Fasten To Adjacent Cabinet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

S t e p 4

Ro ll Re frig e ra t o r

In t o Op e n in g

• Gently push refrigerator into opening with hands

against front corners. The cardboard protective pad

should be beneath the refrigerator.

• Roll refrigerator into the opening until it is flush with

adjacent cabinets.

All models have 4-point leveling. The front is supported

by leveling legs, the rear is supported by wheels.

• To level the back of the refrigerator, turn the 7/16" hex

nut located above the front wheels. Turn to raise or

lower the refrigerator.

S t e p 5

Le ve l

Re frig e ra t o r

Hex Nut Adjusts

Rear Wheels

Leveling Leg

• For front leveling, use a 1-1/2" open-end wrench.

• Adjust carefully, the refrigerator should be level and

plumb with cabinetry, and should align with toekick

height.

S t e p 6

In s t a ll

1 /4 " Do o r

P a n e ls

If you are using 3/4" thick custom panels, SKIP THIS

STEP. See Custom Panel Dimensions pages for panel

sizes with ZKT42 trim kit and other kits. Refer to trim kit

installation instructions in this booklet.

If you are using the custom collar

dispenser trim, order ZWCD1 trim kit.

To install 1/4" door panels:

• Open door to 90° stop. Remove the

Phillips head screws from the

aluminum trim door handles.

Retain all screws.

• Attach 2" x 2" adhesive backed foam pads

to the door. These fillers are shipped with

literature package in snack pan.

• Slide panel into the door

trim.

• Replace door handles

and secure with original

screws.

• Again, check to be sure

unit is level and that

panels align with

cabinetry. Doors will not

close properly if unit is

not level.

• Check for noises caused

by incomplete alignment

(rubbing of panels, trim

or screws).

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

S t e p 7

OP TION 1

S e c u re

re frig e ra t o r

a t t h e t o p

Soffit

WARNING

Block

ANTI-TIP PRECAUTIONS

The refrigerator is heavy at the top and must be

secured to prevent the possibility of tipping forward.

ATTENTION

PRECAUTIONS CONTRE LES BASCULEMENTS

Le réfrigérateur est beaucoup plus lourd en haut et

il faut le maintenir en place pour éviter la possibilité

de son basculement vers l'avant.

To prevent the refrigerator from tipping over, you must:

• Install a wood block, the full width of the refrigerator.

Secure the block with wood screws penetrating at

least 3/4" into wall studs.

Side View

OP TION 2

S e c u re

re frig e ra t o r

a t t h e s id e s

When using 1/2" to 3/4" side panels, the front flange of

the case trim is attached to the side panel.

• Open freezer door to access case trim.

• Drill hole in case trim slightly below top hinge. Drive

screw through the trim and into the side panel.

• Follow the same procedure on the fresh food side.

Top View

Refrigerator Cabinet

Side

Panel

Refrigerator

Door

If refrigerator is installed between cabinets with no side

panels or in a custom enclosure, install a spacer block

as shown.

• Open freezer door to access case trim.

• Drill hole in case trim slightly below top hinge and

drive screw through the trim and into the spacer

block.

Spacer

Block

Refrigerator Cabinet

Refrigerator Door

Top View

• Follow the same procedure for fresh food side.

Spacer

Block

S t e p 8

Co n n e c t

Wa t e r

Check to be sure that refrigerator power cord is not

plugged into the wall outlet.

S u p p ly

• Locate and bring copper tubing to the front of the

cabinet.

• Turn the water on to flush debris from line, run about

a quart of water through tubing into a bucket, then

shut-off water.

• Slip a 1/4-1/4 union nut (provided) over both ends of

the copper tubing at the right front leg of the

refrigerator and couple the lines.

• Turn on the water to check for leaks.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

42" Built-In Refrigerator

S t e p 9

Co n n e c t

p o w e r

• Connect refrigerator power cord plug to properly

grounded receptacle, accessible through the top right

side of the grille opening.

• Check to make sure power to refrigerator is on by

opening refrigerator door to see if interior lights are

on.

S t e p 1 0

Mo u n t

To p Grille

P a n e l

If you are using 3/4" thick custom panels, SKIP THIS

STEP. See Custom Panel Dimensions for grille panel

sizes. Order ZKT42 kit and follow the installation

instructions packed with the kit.

Screws

Top Case Trim

The grille panel frame is factory assembled for an 84"

installation height. If installation height varies, order

ZG2 trim kit which provides optional side trim pieces.

Raise To

Installation

Height

Cut 1/4" thick custom panel to fit the frame,

41" wide, 9" deep.

To insert decorative grille panel into the frame:

• Remove screws (2 on each top corner) and “L”

brackets on each side.

• Slide panel into the frame and reassemble.

• Mount the grille panel by dropping into slots on the

case trim.

• For shipping purposes, the top case trim is secured at

84" installation height and must be adjusted.

To raise or lower case trim to other installation

heights:

• Loosen 2 screws on both sides and raise the top case

trim to meet soffit height or to the top of adjacent

cabinets.

1-1/2"

min.

gap

• Tighten all 4 screws.

If installation height is more or less than 84", order ZG2

optional grille panel kit which accommodates 83",

83-1/2" and 84-1/2" heights. See installation instructions

page 26.

Important: Maintain 1-1/2" min. gap between top of doors and

bottom of panel frame.

S t e p 1 1

In s t a ll

To e k ic k

• A standard toekick is supplied. Install with 2 screws

provided, adjust to desired height and tighten screws.

• A custom toekick can be installed to match or

complement the surrounding cabinetry.

Standard Toekick (Packed with Product)

1/4" Thick Custom Toekick

3-1/4"

– If a custom toekick is to be installed, use the

supplied toekick as a template to cut out notches

around hinges and waterline tubing.

• For 1/2" to 3/4" thick custom toekicks, additional

material should be removed and cut away. This will

allow the water and electrical umbilical tube to rotate

smoothly when the door is fully opened.

1/2" to 3/4" Thick Custom Toekick Remove Additional Material

4-1/16"

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKH1 Trim Kit (For 1/ 4" Panels)

Support for Custom Handles

These instructions are divided into 2 options:

Option 1—For non-dispenser and dispenser models

using custom collar trim.

Option 2—For dispenser model using the standard

full-width trim.

Tools and materials

required:

• #2 Phillips screwdriver

• Drill and appropriate bits

• Custom door panels

• Custom handles

• Safety glasses

Kit

c o n t e n t s

Parts List:

A. Fresh food door

extrusion

B. Freezer door

extrusion for non-

dispenser model and

dispenser model

using custom collar.

(Option 1)

C. Freezer door

extrusion for

dispenser model

using full-width trim.

(Option 2)

D. Handle bracket for

dispenser model using

full-width trim.

(Option 2)

This kit provides the necessary framework to install

custom handles, of your choice, onto 1/4" thick decora-

tor door panels. (Handles not included.) The door

extrusions and bracket allow custom handles to be

secured to the door structure, rather than the door

panels. This kit contains all the necessary parts for

dispenser and non-dispenser models. Follow the

instructions for Option 1 when applying custom handles

to a non-dispenser model or dispenser model using

custom collar trim. Follow instructions in Option 2 for

a dispenser model using the standard full-width

dispenser trim.

OP TION 1

• Open doors to 90°. Remove the screws from the

full-length aluminum handles of both doors.

• Retain screws, discard handles.

Fo r n o n -d is p e n s e r

m o d e l o r d is p e n s e r

m o d e l u s in g c u s t o m

c o lla r t rim

S t e p 1

Re m o ve

h a n d le s

No t e : If a custom collar is to

be used, order ZWCD1 Trim Kit.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKH1 Trim Kit (For 1/ 4" Panels)

Support for Custom Handles

Op t io n 1 In s t a lla t io n

S t e p 2

Lo c a t e p o s it io n

o f h a n d le s

Door Extrusion

3/4" Min.

1-1/2" Max.

No t e : Handle must be located

3/4" to 1-1/2" from edge of

extrusion.

• Again, with both doors closed, check the location of

the centerlines to be sure they are parallel to the edge

of the door, and level with opposite door.

• Slide custom panels into fresh food and freezer door

frames.

• Temporarily secure the new door extrusions to the

doors. Use at least 2 screws on each door.

• The handles must be located 3/4" to 1-1/2" from the edge

of the extrusion.

• Drill 1/16" pilot hole through the panel until it starts into

the aluminum extrusion. This will mark the matching

location for drilling the clearance hole when assem-

bling the handle, panel and extrusion.

• Determine the desired location of the custom handles

and carefully mark centerlines of the screw holes.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKH1 Trim Kit (For 1/ 4" Panels)

Support for Custom Handles

Op t io n 1 In s t a lla t io n

S t e p 3

As s e m b le p a n e l,

e xt ru s io n a n d

h a n d le

Screw

Extrusion

Decorator

Door

Panel

Decorator

Door Panel

Handle

3/4" Min.

1-1/2" Max.

Door Handle

• Remove the door extrusions and door panels.

• Drill 1/16" pilot hole through extrusion.

• Drill clearance holes through the panel and extrusion.

• Assemble the door panel, extrusion and custom

handle.

• Install screw(s) long enough to pass through the

extrusion, door panel and into the handle.

• Slide the assembly into the door frame until the new

extrusion fits firmly against the steel door.

• Re-install original screws into the door extrusion.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKH1 Trim Kit (For 1/ 4" Panels)

Support for Custom Handles

OP TION 2

• Open door to 90°. Remove the screws from the

full-length aluminum handle of the freezer door.

• Retain screws, discard handle.

Fo r d is p e n s e r m o d e l

u s in g fu ll-w id t h

t rim

S t e p 1

Re m o ve h a n d le s

S t e p 2

Re m o ve t rim

Remove door panel trim above and below dispenser.

Lift off dispenser trim. Retain screws and trim.

Remove

Trim

Remove

Dispenser Trim

• Position the handle bracket onto the steel door by

matching existing screw holes on the door and

bracket. Temporary secure with screws.

• Re-install dispenser trim, temporarily.

• Determine the desired location of the custom handle

and carefully mark centerlines of the screw holes.

• Drill 1/16" pilot hole

S t e p 3

Lo c a t e

p o s it io n

o f h a n d le

Temporarily

Secure

Temporarily

Secure

Handle

Bracket

With

Dispenser

Trim

With

Screws

through the trim until it

starts into the handle

Screws

bracket. This will mark

the matching location for

drilling a clearance hole

when assembling the

handle, bracket and

dispenser trim.

• Remove dispenser trim

and bracket.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKH1 Trim Kit (For 1/ 4" Panels)

Support for Custom Handles

Op t io n 2 In s t a lla t io n

S t e p 4

In s t a ll

c u s t o m h a n d le

• Drill clearance holes through the handle bracket and

the dispenser trim.

• Install screw(s) long enough to pass through the

handle bracket, dispenser trim and into the

custom handle.

Dispenser Trim

Handle Bracket

No t e : The custom handle must

be installed against the handle

bracket. The custom handle

cannot exceed 11-3/4" length.

Dispenser Trim

Custom Handle

S t e p 5

Mo u n t

a s s e m b le d

d is p e n s e r t rim

• Mount assembled dispenser trim with handle onto

the door.

• Drive 2 screws through the top and bottom of the

handle bracket into the steel door.

• Re-install 3 screws at top and bottom of

dispenser trim.

Secure

Assembled

Dispenser

Trim

Secure

Handle

Bracket

With

Im p o rt a n t : The handle

bracket must be secured to the

steel door. If it is not secured

properly, the dispenser trim will

pull away from the door.

With

Screws

S t e p 6

In s t a ll

c u s t o m h a n d le

e xt ru s io n

• Slide decorator panels into the trim, top and bottom.

• Slide freezer door extrusion in between panels and

steel door. Secure with screws.

• To install fresh food handle follow the same procedure

as shown in Option 1.

Freezer

Handle Side

Extrusion

Download from Www.Somanuals.com. All Manuals Search And Download.

ZG2 Trim Kit

Grille Panel Frame Adjustment

• This kit provides optional side trim pieces for the

original grille frame to fit 83", 83-1/2" or 84-1/2"

installation heights.

FOR 83", 83-1/2"

AND 84-1/2"

INSTALLATION

HEIGHTS

To change grille panel size:

• Determine the installation height by measuring the

enclosure from the floor to the underside of soffit.

When there is no soffit, measure to the top of

adjacent cabinets.

• Adjust refrigerator case trim to desired height. See

Product Installation.

• Select the side trim pieces for your installation height.

E. Mount the assembled panel by dropping into slots

on the case trim.

Installation

Height

83"

83-1/2"

84-1/2"

Panel

Width

41"

Side Trim

Lengths

8-1/4"

8-3/4"

9-3/4"

Panel

Height

8-1/2"

9-1/2"

1-1/2"

min.

gap

Barrel

Nuts

Discard

Side Trim

Pieces

Important: Maintain 1-1/2" min. gap between top of doors and

bottom of grille panel.

A. Locate original grille panel frame supplied with the

refrigerator.

• Remove 8 screws (two on each corner) as

illustrated. Discard original side trim pieces.

B. Select correct size of side trim pieces (3 sets

provided).

• Secure new side trim pieces to original bottom

trim.

Note: ZG1 Grille Panel Kit is available for models

produced before January 1997. Panel sizes for ZG1 and

ZG2 are the same. The ZG1 kit can be ordered from your

Monogram dealer.

C. Remove barrel nuts from original side trim pieces (2

each side).

• Re-install the barrel nuts on the new side trim pieces

you have selected.

D. Slide custom panel into front slots.

• Secure the top trim piece to the frame with “L”

brackets and screws.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

Tools and materials

required:

These instructions are divided into 2 options:

Option 1—For non-dispenser and dispenser models

using custom collar trim.

Option 2—For dispenser model using the standard

full-width trim.

• #2 Phillips screwdriver

• Stubby Phillips screwdriver

• Drill and appropriate bits

• Safety glasses

• Custom panels

Parts List:

Kit

c o n t e n t s

Freezer Door

A. Top trim

B. Side trim

C. Bottom trim

Fresh Food Door

D. Top trim

E. Side trim

F. Bottom trim

G. Panel support

brackets (4)

H. 4-3/8" screws for

support brackets (20)

I. Grille support panel

and screws

ZKT42–6 screws

J. Wood screws #6 1/2"

flat-head screws

ZKT42–30 screws

This kit provides for the installation of 3/4" custom door

and grille panels, using the standard full length handle.

This kit contains all the necessary parts to apply 3/4"

panels on dispenser and non-dispenser models. Follow

the instructions for Option 1 when applying custom

panels to a non-dispenser model or dispenser model

using custom collar trim. Follow instructions in Option 2

for a dispenser model using the standard full-width

dispenser trim.

No t e : If you are using custom

handles, see ZKHT1 Installation

Instructions. For tubular

stainless steel handles, see

ZKHTSS1 Installation

Instructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

• Open door to 90°.

OP TION 1

Fo r n o n -d is p e n s e r

m o d e l

o r d is p e n s e r m o d e l

u s in g c u s t o m

c o lla r t rim

• Remove the Phillips head screws from the full-length

handles.

• Open the doors fully to stop.

• Remove the screws from the aluminum trim, top,

bottom and hinge side.

• Retain screws. Discard original trim.

S t e p 1

Re m o ve

h a n d le s & t rim

No t e : If a custom collar is to

be used, order ZWCD1 trim kit.

If a custom handle is to be used,

order ZKHT1 trim kit.

Im p o rt a n t : When the bottom

trim piece is removed, an

aluminum shim secured to the

bottom of the door can be seen.

Do not attempt to remove this

piece.

S t e p 2

In s t a ll

3 /4 " t rim

• Attach the new 3/4" trim pieces on the top, hinge side

and bottom using original screws.

42" Models

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

Op t io n 1 In s t a lla t io n

Back Side Door Panel

S t e p 3

Ap p ly p a n e l

s u p p o rt b ra c k e t s

Dimension A

Hinge

Sde

ZKT42–6-3/4"

Support Bracket

Fresh Food Panel

Dimension B

ZKT42–7-7/8"

Bottom Edge

Freezer Panels

Bottom Edge

• Position support bracket on freezer panel,

dimension A, from the hinge side edge.

• Position support bracket on fresh food panel,

dimension B, from the hinge side edge.

• Secure support brackets to the bottom of the panels

with #4 screws provided. Align the brackets flush with

the bottom of the panels, with tabs protruding below.

• Bracket location measured from the hinge side, is the

same for panels with custom handles or standard

handles.

S t e p 4

In s t a ll p a n e ls

ZKT42 – Install 17 screws

• Place the 3/4" panel on the bottom trim with support

bracket tabs inserted into slots. Push the panel back

against the steel door, making sure panel is flush to

hinge side trim.

• Carefully drill starter holes in panel using a small

drill bit.

• Attach the panel to the top and hinge side by installing

screws from the back of the trim through the wood

panel.

• Follow the same procedure to install fresh food

door panel.

• Re-install door handles with original screws.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

Op t io n 1 In s t a lla t io n

S t e p 5

Ad ju s t

g rille p a n e l

h e ig h t

The refrigerator is shipped with the top case trim

secured at the 83" refrigerator height.

• Loosen 2 screws on both sides and raise the top case

trim to meet soffit height, from 83" to 84-1/2".

• Tighten all 4 screws.

Screws

Top Case Trim

Raise To

Installation

Height

Im p o rt a n t : Maintain 1-1/2" min. gap between top of doors and

bottom of grille panel.

S t e p 6

S e c u re 3 /4 "

p a n e l t o

g rille p a n e l

s u p p o rt

• Secure the new grille panel support to the back side

of the 3/4" panel with #6 screws.

• Be sure the lip on the support panel is over the top of

the wood panel.

Panel Support

Overlaps Top

S t e p 7

In s t a ll

g rille p a n e l

1/16"

Back View

Grille Panel Support

• Install four of the six larger under cut screws such

that the top of the screws are 1/16" from the surface of

the support.

• Attach the assembled panel to the grille frame by

inserting the four protruding screws into brackets

located on each side of the grille frame.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

OP TION 2

Fo r d is p e n s e r

m o d e l u s in g

fu ll-w id t h

t rim

• Open freezer door to 90°.

• Remove the Phillips head screws from the full-length

handles.

• Open door fully to stop.

• Remove screws from the aluminum trim, top, bottom

and hinge side.

• Remove the trim above and below the dispenser.

• Retain screws and full-length handles. Discard

original trim.

S t e p 1

Re m o ve

h a n d le s & t rim

S t e p 2

In s t a ll

3 /4 " t rim

• Attach the new 3/4" trim pieces at the top and hinge

side using original screws.

S t e p 3

In s t a ll p a n e l

s u p p o rt b ra c k e t s

• Position and mark the location for the support

brackets on the back side of the panels. Align all

brackets flush with the end of the panels, with tabs

protruding over the edge.

• On the bottom of the upper panel, measure

dimension A from the hinge side.

Back Side

of Freezer

Panels

Hinge

Side

• On the bottom of the lower panel, measure

dimension B from the hinge side.

Upper

Panel

• On the top of the lower panel, measure dimension C

from the hinge side.

• Secure all brackets with #4 screws provided.

Lower

Panel

Dimension A

Dimension B

Dimension C

ZKT42–6-3/4"

ZKT42–4-3/8"

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKT42 Trim Kit

3/ 4" Custom Panels

S t e p 4

In s t a ll

p a n e ls

• Install the lower panel by slipping tabs into the slots

on the underside of the dispenser trim.

• Place the upper panel onto the top of the dispenser

with tabs inserted into the slots.

• Hold in position while fitting new bottom trim against

the bottom of the door. Tabs should protrude through

the bottom trim.

• Push the panel back against the steel door.

• Open door and install screws through the back of the

trim and into the panel, at the top and hinge side.

• Install screws up through the bottom trim using

stubby Phillips screwdriver.

• Open door and install screws through the back side of

the trim and into the panel at the hinge side.

S t e p 5

In s t a ll

h a n d le s

• Install door handle using original screws.

• Re-install top endcaps, if present.

• Install panel on fresh food door using the same

procedure as in Option 1.

• Install grille panel using the same procedure as

in Option 1.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHT1 Trim Kit (For 3/ 4" Panels)

Support for Custom Handles

These instructions are divided into 2 options:

Option 1—For non-dispenser and dispenser models

using custom collar trim.

Option 2—For dispenser model using the standard

full-width trim.

Tools and materials

required:

• #2 Phillips screwdriver

• Stubby Phillips screwdriver

• Drill and appropriate bits

• Custom panels

• Custom handles

• Safety glasses

No t e : This kit must be used in conjunction with ZKT42 trim kit for

3/4" panel trim.

Kit

Parts List:

c o n t e n t s

A. Fresh food door

extrusion

B. Freezer door extrusion

for non-dispenser

model and dispenser

model using custom

collar. (Option 1)

C. Freezer door extrusion

for dispenser model

using full-width trim.

(Option 2)

D. Freezer door handle

bracket for dispenser

model using full-width

trim. (Option 2)

This kit provides the necessary framework to install

custom handles of your choice, on 3/4" thick decorator

door panels. (Handles not included.) The door

extrusions and bracket allow custom handles to be

secured to the door structure, rather than the door

panels. This kit contains all the necessary parts for

dispenser and non-dispenser models. Follow the

instructions in Option 1 when applying custom handles

to a non-dispenser model or dispenser model using

custom collar trim. Follow the instructions in Option 2

for a dispenser model using the standard full-width

dispenser trim.

OP TION 1

Fo r n o n -d is p e n s e r

m o d e l

o r d is p e n s e r m o d e l

u s in g c u s t o m

c o lla r t rim

No t e : Optimal final appearance

depends on careful routing

depth. Do not exceed 1⁄4"

routing depth.

1-13/16"

Back Side

1-13/16"

1/4" Max.

Back Side

Handle Side

Fresh Food Panel

Handle Side

Freezer Panel

Be fo re

yo u b e g in

3/4" custom door panels must be routed to accommodate

these door extrusions. Rout the panels as illustrated, a

maximum of 1/4" deep, and 1-13⁄16" wide, top to bottom

on the handle side.

Refer to installation instructions for ZKT42 trim kit for

3/4" custom panels Option 1.

• Follow Step No. 1 to remove the standard aluminum

trim.

• Follow Step No. 2 and 3 to attach new 3/4" trim

pieces and install panel support brackets.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHT1 Trim Kit (For 3/ 4" Panels)

Support for Custom Handles

S t e p 1

Te m p o ra rily

m o u n t

d o o r p a n e ls

• Secure the panel to the trim temporarily by driving

2 screws through the back side of the trim at the top.

• Slide door extrusion in between panel and steel door.

Temporarily secure with 2 screws.

• Place the prepared 3/4"custom door panels on the

bottom trim with support bracket tabs inserted into

slots.

• Push the panel back against the steel door, making

sure panel is flush with hinge side trim.

S t e p 2

Lo c a t e

p o s it io n

o f h a n d le s

3/4" Min.

1-1/2" Max.

• Drill 1⁄16" pilot hole through the panel until it starts

into the aluminum extrusion. This will mark the

matching location for drilling a clearance hole when

assembling the extrusion, panel and handle.

• Determine the desired location of the custom handles

and carefully mark centerlines of the screw holes.

The handles must be located 3/4" to 1-1⁄2" from the

end of the extrusion.

• Again, with both doors closed, check centerlines of

the screw holes to be sure they are parallel to the

edge of the door, and level with opposite door.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHT1 Trim Kit (For 3/ 4" Panels)

Support for Custom Handles

Op t io n 1 In s t a lla t io n

S t e p 3

As s e m b le p a n e l,

e xt ru s io n

• Remove the door extrusions and door panels.

• Drill 1/16" pilot hole through extrusion.

• Drill clearance holes through the panel and extrusion.

• Assemble the door panel, extrusions and custom

handle.

a n d h a n d le

3/4" Min.

1-1/2" Max.

Screw

• Install screw(s) long enough to pass through the

extrusion, door panel and into the handle.

S t e p 4

Mo u n t

a s s e m b le d

p a n e ls

• Place assembled panel onto bottom trim with support

bracket tabs inserted into slots.

• Push the panel back against the steel door with door

extrusion flush to the handle side of the door.

• Open door fully to stop.

• Install screws at the top, hinge side and end of door

extrusion.

Door Handle

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHT1 Trim Kit (For 3/ 4" Panels)

Support for Custom Handles

Op t io n 1 In s t a lla t io n

OP TION 2

Fo r d is p e n s e r

m o d e l u s in g

fu ll-w id t h

t rim

1-13/16"

Back Side

1-13/16"

No t e : Optimal final

1/4" Max.

appearance depends on careful

routing depth. Do not exceed

1⁄4" routing depth.

Back Side

Handle Side

Fresh Food Panel

Handle Side

Freezer Panel

Be fo re

yo u

b e g in

All 3 custom door panels must be routed to accommo-

date the door extrusions. Route the panels as

illustrated, max. 1/4" deep, 1-13/16" wide, top to bottom

on the handle side.

Refer to installation instructions for ZKT42 trim kit,

Option 2.

• Follow Step No. 1 to remove standard aluminum trim.

• Follow Step No. 2 and 3 to attach new 3/4" trim pieces

and install panel support brackets.

S t e p 1

Lo c a t e p o s it io n

o f h a n d le

Temporarily

Secure

Temporarily

Secure

Handle

Bracket

With

Dispenser

Trim

With

Screws

No t e : The custom handle must

be installed against the handle

bracket. The custom handle

cannot exceed 11-3/4" length.

• Position the handle bracket onto the steel door by

matching existing screw holes on the door and

bracket.

• Drill 1⁄16" pilot hole through the trim until it starts

into the handle bracket. This marks the same location

onto the bracket.

• Re-install dispenser trim, temporarily.

• Determine the desired location of the custom handle

and carefully mark centerlines of the screw holes.

• Remove dispenser trim and bracket.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHT1 Trim Kit (For 3/ 4" Panels)

Support for Custom Handles

Op t io n 2 In s t a lla t io n

S t e p 2

In s t a ll

c u s t o m h a n d le

• Drill clearance holes through the handle bracket and

the dispenser trim.

• Install screw(s) long enough to pass through the

handle bracket, dispenser trim and into the

custom handle.

Dispenser Trim

Handle Bracket

Dispenser Trim

Custom Handle

S t e p 3

Mo u n t

a s s e m b le d

d is p e n s e r

t rim

• Mount assembled dispenser trim with handle onto

the door.

• Drive 2 screws through the top and bottom of the

handle bracket into the steel door.

• Re-install 3 screws at top and bottom of dispenser

trim.

Secure

Assembled

Dispenser

Trim

Secure

Handle

Bracket

With

Im p o rt a n t : The handle

bracket must be secured to the

steel door. If it is not secured

properly, the dispenser trim will

pull away from the door.

With

Screws

Again, refer to ZKT42 trim kit, Option 2.

• Follow Step 4 to install freezer door panels and bottom

trim.

• Slide freezer handle side extrusion in between panels

and steel door. Secure with screws.

• To install fresh food handle, follow the same proce-

dure as in Option 1.

Freezer

Handle Side

Extrusion

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHSS1 for 1/ 4" Panels

Tubular Stainless Steel Handles

This kit provides for the installation of Stainless Steel custom

handles on 1/4" thick decorator door panels. The door extru-

sions allow these custom handles to be secured to the door

structure, rather than to the custom panels. This kit contains

all the necessary parts for dispenser and non-dispenser

models.

Note: It is best that 2 people install this kit.

Tools and materials required:

• #2 Phillips screwdriver

• Drill and 1/8", 9/32" bits

• Custom door panels

• Safety glasses

• Center punch

• Masking tape

• Hammer

• Pencil

• 1/2" thick 12" x 12" min. piece of plywood

to protect floor when drilling

• For stainless steel panels wear gloves to

protect against sharp edges.

Parts List:

A. Fresh food door extrusion

B. Freezer door extrusion

C. 2 Stainless tubular handles

D. 10 Spacer rings (for Stainless panels ONLY)

(8 required, 2 extra)

E. 8 Handle standoffs

F. 10 Screws for mounting handle standoffs

(8 required, 2 extra)

G. 10 Set screws (8 required, 2 extra)

H. 3/32" Allen wrench for set screws

• Open doors to 90°. Remove the screws from the full-

length handles of both doors.

• Retain screws, discard handles.

S t e p 1 :

Re m o ve

Ha n d le s

• Locate the 2" x 2" adhesive foam pads packed with

the refrigerator. Apply pads to the doors as shown.

Corner pads should be as close to inside corners as

possible.

Note: If a custom collar is to be used, order ZWCD1 Trim Kit

for 42" and 42" wide models. Order ZWCD2 for 48" wide

models.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHSS1 for 1/ 4" Panels

Tubular Stainless Steel Handles

S t e p 2 :

Ma t c h

Ha n d le Ext ru s io n s

t o Ha n d le

• Cut a piece of corrugated to use as a pad to protect

the panel finish. Use 1/2" thick section of plywood to

protect flooring when drilling.

• Place custom panels on the pad, appearance side

down.

Note: Be sure to orient

Top

End

extrusions and handles

correctly. The top ends of the

extrusions are cutout to fit the

shape of the top of the door.

Note: If panels are wood, be sure to note which end is

the top so that wood grain is in the correct direction on

both (or all 3) panels.

FOR CUSTOM

WOOD

• On the back side of the panel – at the handle side,

measure and mark 1/4" below the top edge of the

panel with a pencil.

PANELS

Align Extrusion

1/4" Below Top

of Panel

• Slip panels into new extrusion on the handle side of

the panels.

• Align the extrusion at the pencil mark, 1/4" below the

top of the panel.

S e e S t e p 2 A

fo r S t a in le s s

S t e e l p a n e ls

• Follow the same procedure on the opposite panel.

• Tape the extrusions to the panels to prevent move-

ment.

Freezer

Upper

Panel

• Center punch and drill 1/8" pilot holes through the

holes in the extrusion and into the panel.

• Turn panel over. On the appearance side, use 9/32" bit

to enlarge clearance hole.

Back

Side

Fresh

Food

Panel

IMPORTANT: Hole locations must be exact to accept handle

standoff and handle assembly.

Back

Side

Freezer

Panel

Back

Side

Freezer

Lower

Panel

For models with full width dispenser trim and 2 piece

freezer panels:

• Measure 1/4" from the top of the upper panel and 1/4"

from the bottom of the lower panel. Mark with pencil

on the back handle side.

• Align the extrusion on the pencil mark as shown, top

and bottom.

Freezer

Extrusion

Fresh Food

Extrusion

Models

With Full Width

Dispenser Trim

Extrusion

Decorator

Door

Panel

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHSS1 for 1/ 4" Panels

Tubular Stainless Steel Handles

S t e p 2 A:

If you are installing these handles onto Stainless Steel

panels:

• Align extrusion to pencil mark(s) as shown in Step 2.

Mark each screw hole location with pencil.

• Tape extrusions to panels to prevent movement.

• Place panel on plywood section, appearance side

down. Be sure plywood is clean without nicks and

burrs. Center punch at each screw hole location.

• Drill 1/8" pilot hole. Use 9/32" bit to enlarge clearance

hole.

Use extreme caution if you are drilling through

stainless steel panels. Stainless panels must be

handled gently. Do not kneel on stainless steel panels.

It will leave a permanent dent. Do not remove protec-

tive plastic covering until final installation.

• Place supplied filler panel (corrugated) on floor to use

as a pad.

• On the back side of the panel–at the handle side,

measure and mark 1/4" below the top edge of the

panel.

FOR

STAINLESS

STEEL

PANELS

• Measure and cut a 2" wide strip, top to bottom off the

corrugated panels. This will allow room for spacer

rings between the stainless panel and extrusion.

For models with full width dispenser trim and 2-piece

freezer panels:

– Measure and mark 1/4" below the top edge of the

upper panel.

– Measure and mark 1/4" above bottom edge of lower

panel.

• Slip panels into the new extrusion, flush against inner

edge, on the handle side.

• Place a handle standoff on each attachment post

along the handle. Position the set screw hole on each

standoff to point to the floor.

• Install set screws into the bottom of each standoff,

using the Allen wrench provided. The standoff should

be tight against the handle.

S t e p 3 :

In s t a ll

S t a n d o ffs

o n t o Ha n d le s

Screw

Allen Wrench

S t e p 4 :

In s t a ll

Ha n d le s

a n d

P a n e ls

Door

Handle

FOR CUSTOM

WOOD

Screw

PANELS

Decorator

Door Panel

S e e S t e p 4 A

fo r S t a in le s s

S t e e l p a n e ls

Handle

• Screw handle to panel, starting at the top. Moving

down the handle, drive each screw partially into the

standoff, alternating back to the top until the handle is

tight against the panel.

• Slide the assembly into the door frame until the

extrusion fits firmly against the steel door.

• Reinstall original screws into the door extrusion.

• Press foam pads against steel doors to temporarily

reduce thickness.

• Slide panels into the door trim. Leave about 4" of the

panel exposed to allow room to install the handle

extrusion.

• Place extrusion onto back side of panel, install

mounting screws through the extrusion and the

custom panel.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHSS1 for 1/ 4" Panels

Tubular Stainless Steel Handles

S t e p 4 A:

In s t a ll

Ha n d le s

a n d P a n e ls

Door

Handle

FOR

STAINLESS

STEEL

PANELS

Extrusion

Screw

Spacer

Ring

Stainless Panel

Corrugated

1/4"

Handle

Stainless

Panel

For Stainless Panels:

• Press foam pads against steel doors to temporarily

reduce thickness.

• Crimp top and bottom edges of corrugated.

• Slide corrugated onto doors, leave about

1/4" gap between edge of corrugated and hinge side.

• Place a spacer ring over each of the 4 screw holes on

the extrusion. Use tape to hold in place.

• Place extrusion onto back side of panel. Use a pencil to

punch hole in tape over spacer rings and align with

screw holes.

• Install 4 mounting screws through the extrusion and

panel.

• Screw handle to panel, starting at the top. Moving

down the handle, drive each screw partially into the

standoff, alternating back to the top until the handle is

tight against the panel.

Note: Panels have a protective plastic covering. Peel away just

enough to allow panel to slide into trim and to clear handle

mounting screws. The plastic covering will keep the panels clean

during the installation process.

• Slide the assembly into the door frame until the

extrusion fits firmly against the steel door.

• Reinstall original screws into the door extrusion.

• Slide panels into the door trim. Leave about 4" of the

panel exposed to allow room to install the handle

extrusion.

Be sure to maintain 1/4" gap between corrugated and

hinge side trim.

Raised Panel on 1/4" Thick Backing:

5/16"

A raised panel design secured to a 1/4" thick backing

(screwed or glued) can be used with this handle kit.

• Cut the 1/4" thick panels to size.

• Fabricate the raised panel to allow 1-1/4" clearance

from the hinge side to avoid striking adjacent

cabinetry.

• Allow 5/16" clearance at the top, bottom and handle

side edges to allow for the trim flange.

• Total thickness should not exceed 3/4".

• Countertops adjacent to the refrigerator installation

should be mitered 45°.

Appearance

1/4"

Panel

Thick

Backing

1-1/4"

Clearance

Hinge Side

Clearance

5/16"

Handle Side

5/16"

Extrusion

Case Trim

Note: Longer screws, obtained locally, will be required to

accommodate panel thickness. Use stainless steel #10-32x1-1/4"

truss Phillips head screws.

Screw

Adhesive Backed Foam

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHTSS1 for 3/ 4" Panels

Tubulor Stainless Steel Handles

This kit provides for the installation of Stainless Steel

custom handles on 3/4" thick decorator door panels.

The door extrusions allow these custom handles to be

secured to the door structure, rather than to the

custom panels. This kit contains all the necessary parts

for dispenser and non-dispenser models.

This kit must be used in combination with ZKT42, ZKT42

or ZKT48 trim kit.

The ZKT trim kits provide the framework to support 3/4"

thick panels. This kit provides handle side extrusions

and handles to match that ZKT framework.

Note: It is best that 2 people install this kit.

Tools and materials required:

• #2 Phillips screwdriver

• Drill and 1/8", 9/32" bits

• Custom door panels

• Safety glasses

• Center punch

• Masking tape

• Hammer

• Pencil

• 1/2" thick 12" x 12" min. piece of

plywood to protect floor when

drilling

• For stainless steel panels wear

gloves to

protect against sharp edges.

Parts List:

A. Fresh food door extrusion

B. Freezer door extrusion

C. 2 Stainless tubular handles

D. 8 Handle standoffs

E. 10 Screws for mounting handle

standoffs

(8 required, 2 extra)

F. 10 Set screws (8 required,

2 extra)

G. 3/32" Allen wrench for set

screws

• 3/4" custom panels must be routed to accommodate

these handle extrusions. Rout the panels as

illustrated, 1/4" deep, and 1-13/16" wide, top to bottom

on the handle side.

• Follow the instructions in the ZKT trim kit to install

support brackets to the bottom of the fresh food and

freezer panels. For models with full width dispenser

trim, install the support bracket to the bottom of the

lower panel only. Do not install a bracket to the top

of the lower panel or the bottom of the upper panel

as shown in the ZKT trim kit instructions. These

brackets are not required for this kit.

Be fo re

Yo u

Be g in

1-13/16"

Back Side

1-13/16"

1/4" Max.

Back Side

Handle Side

Fresh Food Panel

Handle Side

Freezer Panel

Back Side Door Panel

Hinge

Support Bracket

Side

Bottom Edge

Freezer Panel

Bottom Edge

Fresh Food Panel

Install bottom support brackets only.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHTSS1 for 3/ 4" Panels

Tubulor Stainless Steel Handles

S t e p 1 :

Re m o ve

Ha n d le s

• Open doors to 90°. Remove the screws from the

full-length handles of both doors.

• Retain screws, discard handles.

Note: If a custom collar is to be used, order ZWCD1

Trim Kit for 36" and 42" wide models. Order ZWCD2 for

48" wide models.

S t e p 2 :

Ma t c h

Ha n d le Ext ru s io n s

t o P a n e ls

• Cut a piece of corrugated to use as a pad to protect

the panel finish. Use 1/2" thick section of plywood to

protect flooring when drilling.

• Place custom panels on the pad, appearance side

down.

Note: Be sure to orient

extrusions and handles

correctly. The top ends of

the extrusions are cutout to fit

the shape of the top of the

door.

Top

End

Note: If panels are wood, be sure to note which end is

the top so that wood grain is in the correct direction

on both (or all 3) panels.

• Place new extrusion against the handle side of the

panels.

Align Extrusion

Even With

Panel

• Align the extrusion evenly with the top and bottom of

the panel.

• Follow the same procedure on the opposite panel.

• Tape the extrusions to the panels to prevent

movement.

• Center punch and drill 1/8" pilot holes through the

holes in the extrusion and into the panel.

• Turn panel over. On the appearance side, use 9/32" bit

to enlarge clearance hole.

Freezer

Upper

Panel

Back

Side

Fresh

Food

Panel

IMPORTANT: Hole locations must be exact to accept handle

standoff and handle assembly.

Back

Side

Freezer

Panel

For models with full width dispenser trim and 2 piece

freezer panels:

• Carefully, align the top of the upper panel and the

bottom of the lower panel with extrusion ends.

Back

Side

Freezer

Lower

Panel

Models

With Full Width

Dispenser Trim

Freezer

Extrusion

Fresh Food

Extrusion

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHTSS1 for 3/ 4" panels

Tubular Stainless Steel Handles

• Place a handle standoff on each attachment post

along the handle. Position the screw hole on the

standoff to point to the floor.

• Install set screws into the bottom of each standoff,

using the Allen wrench provided. The standoff should

be tight against the handle.

S t e p 3 :

In s t a ll

S t a n d o ffs

o n t o Ha n d le s

Screw

Allen Wrench

S t e p 4 :

In s t a ll

Ha n d le s

• Start mounting screws through the extrusion and just

through the custom panel.

• Stand panels up on the hinge side and hold to

access the appearance side. Place handle against

mounting screws on the appearance side, drive top

screw from the back of the extrusion partially into the

standoff.

• Going down the handle, drive each screw partially

into the standoff, alternating back to the top until the

handle is tight against the door.

• Remove tape.

Screw

S t e p 5 :

In s t a ll

As s e m b le d

P a n e ls

It is best that 2 people perform this step.

• Place panel/handle assembly onto the bottom trim

with support bracket tabs inserted into slots.

• Push and hold the panel back against the steel door

with door handle extrusion flush to the handle side of

the door.

• Install screws at the top, and hinge side.

• Follow the same procedure on the opposite door.

• Reinstall original screws into the door extrusion.

• Open the door fully to stop.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZKHTSS1 for 3/ 4" Panels

Tubular Stainless Steel Handles

S t e p 5

In s t a ll

As s e m b le d

P a n e ls

(c o n t in u e d )

For models with full width dispenser trim and 2 piece

freezer panels:

It is best that 2 people perform this step.

• Carefully, lift the assembled panel to the case trim.

Hold both panels so they do not twist the extrustion.

• Insert the support bracket tabs into the bottom trim.

• Push and hold the panel back against the steel door.

• Reinstall original screws into the door extrustion.

• Open the door fully to stop.

• Install screws at the top, and hinge side.

Download from Www.Somanuals.com. All Manuals Search And Download.

ZWCD1 Trim Kit

Custom Dispenser Collar

Tools and materials

required:

• #2 Phillips screwdriver

• Drill and appropriate bits

• Custom door panels

• Safety glasses

Parts List:

Kit

c o n t e n t s

A. Collar trim

(Both black and white

trim included)

B. Top bracket

C. Bottom bracket

D. Screws (2)

This kit provides for the

use of a custom dis-

penser collar trim,

replacing the standard

full-width trim. This kit

can be used alone, or

combined with one or all

other trim kits.

S e le c t

p a n e l s ize

3/4" Thick Custom Panels

with Standard Handles

3/4" Thick Custom Panels

with Custom Handles

1/4" Thick Custom Panels

17 11/16"

2 9/16"

17 11/16"

67 15/16"

67 7/8"

67 15/16"

2 9/16"

2 5/16"

15 1/4"

15 1/16"

15 5/16"

The overall size of the panel is determined by the

application being used.

• 3/4" thick panels using optional custom handles.

Select the panel size accordingly.

• 1/4" thick panels using the standard handles or

optional custom handles.

• 3/4" thick panels using standard handles, or

Download from Www.Somanuals.com. All Manuals Search And Download.

ZWCD1 Trim Kit

Custom Dispenser Collar

Cu t d is p e n s e r

h o le a n d ro u t

d o o r p a n e l

The use of this custom collar trim requires that the hole

for dispenser be located and cut very accurately. 3/4"

door panels must be routed on all 4 sides of the

dispenser cutout.

9 7/16"

7/8"

Wide

Rout

Rout the back side of the panel 1/4" deep and 7/8" wide,

flush with the edge of the cutout.

12 5/16"

The Cutout is 9 7/16" wide

by 12 5/16" high. 3/4" panels

must be routed on all four

sides of the cutout. Rout

the back side of the panel

1/4" deep. 7/8" wide.

No t e : 1/4" door panels do not

require routing.

In s t a ll

c o lla r

b ra c k e t s

a n d t rim

Select the door panel size for your application.

• If using the standard 1⁄4" trim, follow the installation

instructions packed with the product.

• When using another optional trim kit, use the

instructions provided with that kit to install the panel

trim and/or custom handles.

• Secure top and bottom brackets to the dispenser,

using the screws previously removed.

• Install the custom panels according to the appropriate

installation instructions.

• Select the black or white collar trim according to

appearance desired.

• Remove the aluminum trim above and below the

dispenser. Discard trim.

• Remove and discard the standard full-width

dispenser trim.

• Remove 2 screws above and below the dispenser

recess. Retain screws.

• Match the indentations on the collar trim to the tabs

on the lower bracket. Push the collar flush against

the door.

• Drive 2 screws (provided) upwards through the collar

and into the brackets.

Download from Www.Somanuals.com. All Manuals Search And Download.

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

To obtain specific information concerning any

Monogram product or service, call GE Answer Center^®

consumer information service at 800.626.2000–any

time, day or night.

For Monogram local service in your area, call

1-800-444-1845.

Note: Product improvement is a continuing endeavor at

General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

Pub. No. 49-6963-2

Part No. 162D9630P002

Printed in U.S.A. ( NAI 484) 12/99

70759

Monogram.

General Electric Company

Louisville, KY 40225

Download from Www.Somanuals.com. All Manuals Search And Download.

Crosley Radio CD Player CR2413A BK User Manual
Cuisinart Coffeemaker DCC1200E User Manual
Cypress Computer Hardware CY8C21234 User Manual
Dacor Blower ILb10 User Manual
Dynasty Spas Hot Tub MC MP CE User Manual
Electro Voice Portable Speaker QRx153 User Manual
Everpure Water System Quad XC User Manual
Festool Sander ETS 150 3 EQ User Manual
GE Air Conditioner AEE12DK User Manual
Gitzo Camcorder Accessories GT2531EX User Manual