ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator
with Dispenser and Water Filter
Dimensions and Clearances (in inches)
* Shipping height.
41"
The Installation Space
25-3/8
Case Width
The refrigerator
can be adjusted to
fit into a cutout that
is 83-1/2" min. to
84-1/2" max. height
Note that the top
case trim at the
36" Models 12"
42" Models 18"
48" Models 20"
*Finished Width
*84" From
Floor to
Top Frame
*83-1/2"
at
Rear
6"
Electrical
Area
front is 1/2" higher
and will overlap
upper cabinetry or
soffit. Use leveling
legs and wheels for
a maximum 1" height
adjustment.
84-1/2" max
83-1/2" min
Finished
5"
75" From Floor
to Bottom
of Electrical
Area
Opening
42"
24"
26-7/8"
including
handle
Frame to Frame
5"
5"
Water Supply
3-1/2"
Door Swing Clearances
3-1/2"
The installation must allow for clearances to adjacent walls or
cabinets. These refrigerators are equipped with a 2-position
door stop. The factory-set 130° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.
Space is the first consideration when planning the installation.
The cutout depth must be 24"
The refrigerator will project forward, slightly beyond adjacent
cabinetry, depending on your installation.
90° Door Swing
130° Door Swing
13"
19"
23-7/8"
Behind
Frame
The cutout depth beneath a soffit
When installed beneath a soffit, the soffit cannot exceed the
24" installation depth shown. The top case trim overlaps the
bottom of the soffit.
26-5/8
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall. Electrical must be
located on rear wall as shown.
4" Min.
to Wall
Allow minimum clearances for freezer door and fresh food
door for a full 130° door swing and to allow for pan removal.
• 4" minimum clearance is required when door swing is
adjusted to 90°. If the 90° door stop position is used, pan
access is maintained, but pan removal is restricted.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
All models are equipped with an automatic icemaker. The
water line can enter the opening through the floor or back
wall. Route 1/4" O.D. copper tubing or GE QuickConnect
kit between the cold water line and the water connection
location. The copper tubing should be long enough to extend
to the front of the refrigerator. The installation of an easily
accessible shut-off valve in the water line is required.
• See door swing illustrations to determine interaction with
adjacent cabinets or countertops.
Installation Information: Before installing, consult
installation instructions packed with product, or online at
Monogram.com, for current dimensional data.
For answers to your Monogram,® gE Profile™ or
As an EnErgy StAr®
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
gE® appliance questions, visit our website at
Listed by
Underwriters
Laboratories
gEAppliances.com or call
gE Answer Center® service, 800.626.2000.
Specification Revised 3/08
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator
with Dispenser and Water Filter
3/4" Overlay Panel Dimensions
Raised Overlay Panel Design
On Dispenser Models
For a more custom appearance, overlay
panels may be installed on trimmed
models. the overlay panel must be
secured to a 1/4"-thick backer panel
which slides into the trim. A spacer
panel 0.10" thick must be placed
When a raised panel design is to be used, a custom wide middle rail
Door
3/4"
Overlay
Panel
is required to accept the dispenser trim.
• the middle rail must be wide enough to allow for the dispenser
trim to overlap the opening.
• the middle rail must be 1.100" total thickness to accept the
dispenser trim.
between the overlay and backer panels.
1/4" Backer Panel
3/4" Overlay Panel
.250" + .10" + .750" =
1.100" total Panel thickness
1/4"
Backer
Panel
.10"
Spacer
Overlay Panel
Spacer Panel
Backer Panel
Center each panel over the other.
Assemble the panels with glue
and screws. Screws must be
Dispenser
Trim
Wide
Middle
Rail is
16-3/4"
Required
countersunk into the backer panel.
NOTE: Left-to-right offset is
not always equal to
top-to-bottom offset.
10-5/8"
Side View
A
42" Side-by-Side (in inches)
Grille Panel
B
C
A
B
C
D
E
1/4" Backer Panel 39-7/8 9-1/2 68-3/8 14-9/16 24-9/16
.10" Spacer Panel 39 8-5/8 67 13-1/4 23-1/4
F
Dispenser
Cutout
3/4" Spacer Panel 40-1/8 9-3/4 68-5/8 14-13/16 24-13/16
Dispenser Cutout
Dispenser Cutout Position (in inches)
G
F
G
42" Models
17-15/16
3-1/4
15-3/
Freezer
Panel
Fresh
Food
D
9-5/8"
As an EnErgy StAr®
*Cut the dispenser opening after the backer, spacer and overlay
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
Listed by
Underwriters
Laboratories
panels have been assembled.
Important Note: Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
For answers to your Monogram,® gE Profile™ or
gE® appliance questions, visit our website at
gEAppliances.com or call
• grille panel – 18 lbs.
gE Answer Center® service, 800.626.2000.
Specification Revised 3/08
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator
with Dispenser and Water Filter
1/4" Framed Panel Dimensions
Dispenser Models
If you choose to install framed panels,
they must be cut to the dimensions
shown. the panels will slide into the
frame on the door and grille.
these refrigerators are supplied with two dispenser trims, one for
5/16"
Trim
framed panels and one for overlay panels.
Door
Revea
1/4" Framed Panel
the framed panel must be 1/4" nominal thickness to fit the
If the custom panel is less than 1/4" thick,
and it fits loosely in the door frame, it can
be backed up with a piece of filler material
or foam tape to improve the fit.
dispenser trim.
1/4"
Panel
• the dispenser trim fits over the custom panel and snaps into the
freezer door.
• If the panel is less than 0.250" thick, a noticeable gap may be
created around the dispenser trim. Foam tape may be applied on
the door to improve the fit.
• If the panel is more than 0.250" thick, the dispenser trim cannot be
secured to the door.
Important Note:
Maximum total panel weight:
• Fresh food door panel – 75 lbs.
• Freezer door panel – 53 lbs.
• grille panel – 18 lbs.
39-7/8"
FREEZER DOOR
1/4"
Framed
Panel
0.250"
Thick
Grille Panel
9-1/2"
Ice / Water Dispenser
1/4" Dispenser Trim
17-13/16
Dispenser
Cutout
3/4" Overlay Panels
the overlay dispenser trim is designed to fit a total panel thickness
of 1.100".
• If the panel is less than 1.100" thick, a noticeable gap may be
created around the dispenser trim.
68-3/8
3-1/8"
• If the panel is more than 1.100" thick, the dispenser trim cannot be
secured to the door.
• the overlay panel must be constructed according to the specifications
shown to achieve the correct total thickness.
Freezer
Panel
Fresh
Food
• Alternative panel construction methods such as securing a
3/4" panel to a 1/4" backer panel cannot be used. Another method,
routing a 3/4"-thick panel on all sides, cannot be used. these
methods will not result in the required 1.100" panel thickness.
14-9/16"
24-9/16"
• When a raised panel design is to be used, a custom middle rail
is required.
Dispenser Cutout
1/4" Backer Panel
1.100"
Total
Thickness
FREEZER DOOR
.10" Spacer
Panel
15-3/
Ice / Water Dispenser
3/4" Overlay
Panel
3/4" Overlay Dispenser Trim
9-5/8"
For answers to your Monogram,® gE Profile™ or
gE® appliance questions, visit our website at
gEAppliances.com or call
As an EnErgy StAr®
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
Listed by
Underwriters
Laboratories
Specification Revised 3/08
gE Answer Center® service, 800.626.2000.
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side
Refrigerator with Dispenser
and Water Filter
Advance Planning for Built-In Custom Side-by-Side Refrigerators
Use this page to determine door swing
interaction with adjacent cabinets
or countertops.
Frameless Cabinets: the case trim overlaps
cabinets at the top and sides. therefore,
frameless cabinets may require filler strips
to prevent interference with cabinet door swing.
the opening must allow for filler strips.
Refrigerator
23-7/8" From
Rear of
Refrigerator
1"
2"
1-3/4"
3"
2-3/4"
Case
Trim
3/4"
1/2"
1/4"
1-1/2"
1-1/4"
2-1/2"
2-1/4"
Top View
130° Door Swing
(Factory setting)
Scale 1:1
1/4"
1/2"
3/4"
1"
IMPORTANT NOTE –
FOR DISPENSER MODELS
Dispenser models are supplied with
two dispenser trims, one to fit framed panels
and one for overlay panels. Dispenser trim fit
to the custom panel depends on correct
panel thickness. Framed panels
must be 1/4" nominal. Overlay panels
should be constructed as shown
to accomplish a total
1.100" thickness.
1/4"
1/2"
3/4"
1"
1-1/4"
Door
3/4" Overlay
Panel
(Nominal Size)
Listed by
Underwriters
Laboratories
As an EnErgy StAr®
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
For answers to your Monogram,® gE Profile™ or
gE® appliance questions, visit our website at
gEAppliances.com or call
gE Answer Center® service, 800.626.2000.
Specification Revised 3/08
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side
Refrigerator with Dispenser
and Water Filter
Advance Planning for Built-In Custom
Side-by-Side Refrigerators
Refrigerator
Use this page to determine door swing
interaction with adjacent cabinets
or countertops.
Case Trim
23-7/8"
From Rear of
Refrigerator
Frameless Cabinets: the case trim overlaps
cabinets at the top and sides. therefore,
frameless cabinets may require filler strips
to prevent interference with cabinet door swing.
the opening must allow for filler strips.
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
Top View
90° Door Swing
(Optional setting)
Scale 1:1
IMPORTANT NOTE –
FOR DISPENSER MODELS
Dispenser models are supplied with two dispenser
trims, one to fit framed panels and one for overlay
panels. Dispenser trim fit to the custom panel
depends on correct panel thickness. Framed
panels must be 1/4" nominal. Overlay panels
should be constructed as shown to accomplish
a total 1.100" thickness.
1/4"
Door
1/2"
3/4"
Listed by
Underwriters
Laboratories
1"
As an EnErgy StAr®
partner, gE has determined
that this product meets the
EnErgy StAr guidelines
for energy efficiency.
1-1/4"
3/4" Overlay
Panel
(Nominal Size)
For answers to your Monogram,® gE Profile™ or
gE® appliance questions, visit our website at
gEAppliances.com or call
gE Answer Center® service, 800.626.2000.
Specification Revised 3/08
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
ZISW/B420DR – GE Monogram 42" Built-In Side-by-Side Refrigerator
with Dispenser and Water Filter
Features and Benefits
• 26.1 cu. ft. total capacity
• Overhead evaporator
• Integrated Ice™ System – the ice bucket is integrated
into the icemaker, not the freezer door, freeing up
valuable storage space
• Upfront electronic controls with digital readout
• Multi-shelf halogen light tower (Both fresh food
and freezer section)
• Multi-shelf air management tower
• Climate control drawer with Express Chill,
Express thaw and Select temp
• Sealed adjustable humidity produce pan with
easy access lid and full extension slides
• Disappearing electronic glass touch dispenser controls
with proximity sensor
• Model ZISW420Dr – White dispenser
• Model ZISB420Dr – Black dispenser (shown)
Specification Revised 3/08
110171
Download from Www.Somanuals.com. All Manuals Search And Download.
|