GE Monogram Microwave Oven ZEM200WV User Manual

GE Monogram®  
Installation  
Instructions  
Under Cabinet Installation  
and  
JX827WN Built-In Kit  
Microwave Oven  
Model  
ZEM200WV  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Design Information  
Microwa ve Oven  
ZEM2 0 0 WV  
White electronic  
microwave oven  
Mo d e l  
a va ila b le  
Designed for versatility, this Monogram microwave  
oven adapts to virtually any installation. Accessory kit  
JX827WN is required for custom in-wall installation.  
ZEM2 0 0 WV  
Dim e n s io n s  
a n d c le a ra n c e s  
A - 12-5/16" (284 mm)  
B - 23-13/16" (605 mm)  
C - 11-3/16" (284 mm)  
(includes feet)  
No t e : When installed, trim kit  
will require wall space 26-1/8"  
W x 16-1/4" H for clearance.  
Wall Cutout ZEM200WN  
This microwave oven can be used on the countertop,  
built into a wall or suspended beneath a cabinet.  
Accessory kit JX827WN is necessar y for custom in-wall  
installation.  
In s t a lla t io n  
o p t io n s  
All necessary hardware for under cabinet installation  
comes packed with the product.  
• Do not install this microwave oven above a cooktop,  
range or other heating surface.  
• Using the accessor y kit, this microwave oven can be  
installed alone or over any Monogram single electric  
wall oven.  
Ad va n c e  
p la n n in g  
Refer to “Cabinetry” for complete details on prepara-  
tion for in-wall installation.  
• 12" deep cabinet is preferred, though oven may be  
mounted on shallower cabinetry.  
• A 3-prong grounding wall receptacle must be within  
reach of the 57" power cord:  
If you wish to mount the ZEM200WV beneath a  
cabinet:  
– Receptacle should not be directly behind oven, but  
should be out of view when oven is installed.  
• Check that cabinet is securely installed, using more  
than two screws at top:  
• Cabinet must be wood or metal, in good condition.  
• Cabinet bottom must be capable of supporting an  
additional 90 pounds.  
Wood cabinet bottom must be at least 3/ 16" thick  
masonite or plywood.  
– If not, add two screws at cabinet bottom, making  
sure they enter wall studs at least 1/ 2".  
• Underside of cabinet must be at least 24" wide.  
• Refer to “Installation” for further details.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Microwave Oven  
ZEM2 0 0 WV  
In -w a ll  
in s t a lla t io n  
Tools and materials required:  
• 3/8" thick plywood (min.)  
• 2" x 4" lumber  
• Saw  
• Screws and screwdriver or other hardware for construction of  
plywood base.  
Opening for model ZEM200WV must be:  
• 24 -7/ 8" ± 1/ 16" wide.  
• 15" ± 1/ 16" high.  
• With approximately 1-1/ 4" for oven trim overlap  
around all edges of opening.  
• Deep enough to accommodate electrical receptacle  
and permit adequate air circulation for proper  
venting:  
– Minimum 18" deep with receptacle inside cutout.  
– Minimum 16" deep with receptacle outside cutout.  
Height from floor may vary according to preference  
of user.  
No t e : When installed, trim  
kit will require wall space  
26-1/8" W x 16-1/4" H for  
clearance.  
Within opening of appropriate dimensions:  
• Install a level base of plywood:  
– Flush with lower edge of opening.  
– Entirely covering floor of opening.  
3/ 8" thick (min.) plywood must be supported by  
2" x 4" or 1" x 2" equivalent runners on all sides.  
• Finished floor must support a minimum of 100  
pounds.  
• JX827WN accessory kit may be assembled and  
installed at this time. Refer to “Installation” for  
instructions.  
The JX827WN accessory kit provides trim strips to  
conceal all raw edges of cabinets.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Microwave Oven  
ZEM2 0 0 WV  
Wit h s in g le  
o ve n  
Refer to diagram at right  
for dimensions when  
installing ZEM200WV  
above a Monogram  
single oven.  
No t e : Trim kit JX827WN is  
required for installation above a  
single oven.  
Within opening of appropriate dimensions:  
• Install a level base of plywood:  
– Flush with lower edge of opening.  
– Entirely covering floor of opening.  
3/ 8" thick (min.) plywood must be supported by  
2" x 4" or 1" x 2" equivalent runners on all  
four sides.  
• Finished floor must support a minimum of  
100 pounds.  
• Assemble JX827WN accessory kit, refer to  
“Installation” for details.  
ZEM2 0 0 WV  
Un d e r-c a b in e t  
m o u n t in g  
The ZEM200WV may be installed under virtually any  
cabinetr y and is supplied with all hardware necessary  
for under-cabinet installation. Cabinet bottom must  
be capable of supporting an additional 90 pounds.  
Refer to “Advance Planning” for more details.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Microwave Oven  
Ele c t ric a l  
s u p p ly  
Tools and materials required:  
• 3-prong grounded electrical receptacle.  
Electrical cable, 2-wire with ground, No. 14 minimum,  
as required.  
Monogram microwave ovens require a 120 volt, 60 Hz  
power supply, protected by a time delay fuse or circuit  
breaker.  
ZEM200WV oven is supplied with a power cord 57"  
long for which a properly grounded 3-prong electrical  
receptacle is required.  
• 800 watt* oven ZEM200WV draws 1360 watts,  
with a 13 amp load.  
No t e : Do not use an extension  
cord with these appliances.  
*IEC-705 test procedure  
ZEM2 0 0 WV  
In -w a ll  
in s t a lla t io n  
• Install a 3-prong grounded receptacle.  
• Receptacle may be within opening (shaded area in  
diagram):  
– If using this installation, be sure opening is  
sufficiently deep to accommodate power cord and  
plug (18" min.).  
• Receptacle may also be placed outside shaded area,  
within reach of ovens 57" power cord. In this case,  
opening need only be 16" deep.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation Preparation  
Microwave Oven  
ZEM2 0 0 WV  
In -w a ll  
in s t a lla t io n  
(c o n t in u e d )  
• When cabinet depth is a critical factor, receptacle  
should be installed in a side wall at rear of opening:  
– 14 -5/ 8" minimum cabinet depth is required.  
Receptacle installed in side  
wall.  
• If receptacle is located behind oven, install receptacle  
flush with wall to minimize depth:  
– 16" minimum depth is required.  
Receptacle installed behind  
oven, flush with wall.  
• If receptacle is located behind oven and extended  
into cabinet:  
– 18" minimum cabinet depth is required.  
Receptacle installed behind  
oven, extended into cabinet.  
ZEM2 0 0 WV  
Un d e r-c a b in e t  
m o u n t in g  
• A 3-prong grounded receptacle must be within reach  
of the ovens 57" power cord, but located out of view  
when oven is installed.  
• Allow access for plugging and unplugging; do not  
place receptacle directly behind oven.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
J X8 2 7 WN  
in s t a lla t io n  
Tools and materials  
required:  
Accessory kit JX827WN for  
in-wall installation of  
ZEM200WV  
7
4
5
D
6
B
A
• 2 Phillips head screwdrivers  
(#1 & #2)  
1
E
C
Drill and 3/32" drill bit  
Centerpunch or nail  
Pencil and ruler  
2
Parts Inventory  
JX827WN Parts List  
1. Base Pan  
3
3
2. Rear Duct  
3. Side Covers (2)  
4. Top Trim  
5. Bottom Trim  
6. Side Trims  
7. Rear Holddown Brackets  
Screws A (9 required 1 extra)  
B (4 required 1 extra)  
C (10 required 2 extra)  
D (4 required 1 extra)  
E (4 required 1 extra)  
Screw A  
Screw B  
Screw C  
Screw D  
Screw E  
Screw B  
Screw C  
• Slide two rear holddown brackets into slots in the  
rear of base pan. Tongues should be sticking into  
the base pan and centered in the slot.  
• Mark and drill four 3/ 32" holes.  
• Set the base pan into cabinet cutout and center left  
and right. Front flange should be pushed back  
against front wall, flush with opening.  
• Mark the opening precisely at the center line.  
• Drill two 3/ 32" diameter holes into the base  
supporting structure, using the two holes in the base  
pan front flange as a guide.  
• Mount both brackets.  
• Remove two screws in the base pan front flange and  
slide the base pan straight out.  
• Drive two screws into the base pan front flange to  
temporarily hold in place.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
J X8 2 7 WN  
in s t a lla t io n  
• Remove the four top plug buttons from the top of  
the microwave oven cabinet.  
• Place the microwave oven on the base pan centered  
left to right.  
No t e : Do not tighten screws until all screws are started.  
• Install side cover by inserting between oven and  
base pan.  
• Start two screws A, through side cover and two  
screws E, through the cover on top into holes where  
buttons were removed.  
• Install other side cover with screws A.  
• Install other top screws E.  
• Tighten all screws.  
• Remove screw located on the top left of the back of  
the oven. Retain screw.  
Screw A  
Screw E  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
J X8 2 7 WN  
in s t a lla t io n  
Screw A  
• Install rear duct by inserting into bottom flange  
between the oven and back of base pan.  
– The rear duct should be as far to the left as  
possible, between the base pan back flange and  
the partition on the right side.  
• Drive one screw into the rear duct side flange near  
the lamp cover.  
• Drive three screws through the base pan into the  
rear duct bottom.  
• Replace the screw removed from the top left to  
complete the rear duct.  
• Locate and use screws A.  
• Drive one screw through the rear duct into the  
partition in the base pan.  
• The kit should be completely sealed to the micro-  
wave oven in the back.  
Screw C  
Ca u t io n : Do not pinch  
power cord.  
• Drive two screws through the base pan front flange  
through the holes drilled initially.  
• Plug the power cord into the wall receptacle.  
• Gently slide the microwave oven assembly into the  
cabinet opening, keeping it centered.  
• Push to the back, allowing tongues of rear brackets  
to slide through rear slots.  
• Check to be sure oven is centered.  
• Locate and use screws C.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
As s e m b le  
t rim k it  
fra m e  
• Assemble top, bottom  
and side trims with four  
screws D, as illustrated.  
Screw D  
When assembled, top,  
bottom and side strips  
must be flush.  
No t e : Bottom trim has a hinge  
notch and is not interchangable  
with top trim.  
In s t a ll  
t rim k it  
fra m e  
Ca u t io n : Do not overtighten  
screws; doing so could cause  
misalignment of top and side  
strips.  
Screw C  
• Use the assembled frame as a template. Insert the  
frame into the cut-out and locate the attaching  
holes.  
• Mark the four holes on the side of the trim.  
• Remove the frame.  
• Center punch and drill 3/ 32" pilot holes.  
• Temporarily hold the frame in place by starting the  
four screws that attach the frame to the base pan  
and side covers.  
• Position the assembled frame around the oven and  
secure with 8 screws C, using the smaller Phillips  
head screwdriver to prevent burring the Phillips  
head.  
• Push frame as far left as possible, drive the four  
screws.  
• Check to be sure door clears the trim when open.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwa ve Oven  
ZEM2 0 0 WV  
Un d e r-c a b in e t  
m o u n t in g  
Tools and materials  
required:  
Flat-blade screwdriver  
Phillips screwdriver  
Drill and 1/4" bit  
Nail or center punch  
Pencil and ruler  
• Scissors  
Hammer  
Tape  
Line cord holder (supplied)  
Two brackets (supplied)  
1513/32"  
Template 1  
3
/
4
1
/
2
1
/
4
Template 2  
• Carefully remove the four plastic plug buttons from  
Mounting holes for the oven should be drilled from  
oven top and the two screws at top rear flange of case. the inside, if cabinet shelves are removable to allow  
• Remove the two top case screws on the back of oven. enough space. Holes may be drilled from bottom,  
Retain screws.  
if necessar y.  
• Secure the two rear brackets to back of the oven, left  
and right, using screws removed earlier.  
– Make sure brackets are level and flush with top  
surface of case.  
• Cut Template 1 along dotted lines.  
• Place Template 2 inside the cabinet:  
To d rill  
fro m in s id e  
– If cabinet is less than 12" deep, cut off front edge of  
template to fit, using template cut lines as a guide.  
– If cabinet has a recessed shelf, measure the  
thickness of the front rail and cut that amount off  
the front edge of template. This will allow template  
2 to lie flat.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
To d rill  
fro m in s id e  
(c o n t in u e d )  
– Position remaining piece of Template 2 inside cabinet • With template secured in place, check again that  
and align hole center line with arrows on Template 1.  
– Cut excess paper from center of Template 2 so it will  
lie flat.  
hole center lines on Template 2 are straight, and  
that distance from right to left hole center measures  
distance shown on template.  
– Distance from right hole center to left hole center  
should measure distance indicated on template.  
– Tape remaining portion of Template 2 in place.  
To d rill fro m  
b o t t o m  
• Position Template 2 flat against underside of cabinet:  
– If cabinet is less than 12" deep, cut that amount off  
front edge of template.  
– If cabinet has a front rail, cut front edge of  
template to fit; place cut edge against back of  
front rail.  
– Cut template to fit around corner brackets or glue  
blocks underneath cabinet.  
If c a b in e t  
h a s a  
p a rt it io n  
If cabinet has partition:  
– Cut Template 2 into two pieces to fit on either side  
of partition.  
– Align front edge of one template piece with front  
edge of cabinet or back of front rail; tape in place.  
– Tape Template 1 to rear of cabinet, aligning arrow  
with hole center line on Template 2.  
– Position remaining piece of Template 2 under  
cabinet and align hole center line with arrows on  
Template 1.  
– Cut excess paper from center of Template 2 so it  
will lie flat.  
– Distance from right hole center to left hole center  
should measure distance indicated on template.  
– Tape remaining portion of Template 2 in place.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Installation  
Microwave Oven  
Fin a lize  
u n d e r-c a b in e t  
in s t a lla t io n  
13/16"  
• With template secured in place, check again that hole • Select four bolts—one of each size—from parts  
center lines on Template 2 are straight, and that  
distance from right to left hole center measures  
distance shown on template.  
package.  
Hold each bolt against cabinet front rail.  
• Select bolt that extends beyond top of bottom shelf  
by 3/ 16" to 13/ 16".  
• Drill mounting holes:  
– Use of safety glasses is recommended to protect the  
eyes.  
– Correct bolt length is important. If bolt is too  
short, it wont reach oven; if bolt is too long, oven  
will not be drawn up tight to cabinet.  
• From inside cabinet, insert four bolts, all same  
length, through mounting straps and then into  
drilled holes of cabinet shelf.  
– Empty cabinet and remove delicate items from  
adjacent cabinets.  
– Use center punch or nail to make an indentation  
for centering the drill bit.  
Holding drill straight, drill through Template 2 at  
the four black drilling holes indicated on template.  
– Remove template and clean drill holes.  
• Place solid support, such as a stack of books, under  
oven to raise it close to cabinet bottom.  
• Align mounting holes on oven with bolts.  
• Lift oven, and insert bolts into mounting holes.  
• Tighten bolts alternately to draw oven up evenly and  
secure it to cabinet bottom.  
• Remove ovens rubber feet and save for future use.  
• Plug power cord into receptacle.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Notes  
Microwave Ovens  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE: While performing installations described in this book,  
safety glasses or goggles should be worn.  
To obtain specific information concerning any  
Monogram product or service, call GE Answer Center®  
consumer information service at 800.626.2000—any  
time, day or night.  
For Monogram local service in your area, call  
1-800-444-1845.  
NOTE: Product improvement is a continuing endeavor at General  
Electric. Therefore, materials, appearance and specifications are  
subject to change without notice.  
Pub. No. 49-8799  
1996 GE Appliances  
(N.D. 524) 9/ 96  
®
Monogram.  
General Electric Company  
Louisville, KY 40225  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Conair Indoor Furnishings BE87CR User Manual
Conair Skin Care Product Facial Steamer User Manual
Dell Server C2100 User Manual
Delta Electronics Network Card TAP CN01 02 03 User Manual
Dimplex Indoor Fireplace lee de luxe User Manual
DXG Technology Camcorder DXG 589V User Manual
Extron electronic Stereo Receiver TP Series User Manual
Fisher Price Motorized Toy Car 73260 User Manual
GBC Paper Shredder RDS 1713 User Manual
GE Ventilation Hood JV394S User Manual