GE Model 19208
Wireless Door Chime Kit
Installation Instructions for Battery Operated
Wireless Door Chime Kit
Prior to Installation the Try-Me feature must be removed.
1. Remove the battery cover on the chime.
2. Remove the white Styrofoam block
3. Unplug the red and black wires inside the battery compartment.
4. Remove the battery pack and discard appropriately.
House Code
Door
Styrofoam
Block
Try-Me Wires
Chime components
Required Tools: Small flat blade screwdriver, drill, 1/16” and 5/32” drill bits,
and phillips screwdriver.
Included Hardware:
(2) Plastic screw anchors
(2) 4x20mm screws
(2) 3x20mm screws
(2) Double sided adhesive pads
Download from Www.Somanuals.com. All Manuals Search And Download.
Chime Dip Switches
(Ding Dong Shown)
House Code Jumpers
Pushbutton Dip Switches and Jumpers
Setting The House Security Code
Each chime component has 4 jumpers for setting the house security code.
In most cases you will not need to change the factory settings for the house
security code. If your chime activates intermittently or does not work at all,
you may be able to solve the problem by changing your security code.
1. Remove power or batteries from the chime.
2. To remove the batteries from the pushbutton, open the pushbutton case
as shown below.
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Locate the House Security Code door and screw located on the
back of the chime (See the chime components picture above). Remove
the screw and take off the door.
4. Locate the chime and pushbutton jumpers shown below.
House Code Jumpers
Chime and Pushbutton Jumpers
5. To change the house code, add or remove jumpers as needed. It is
recommended to change only one jumper at a time and then test the
system for proper operation. The jumpers on the chime and pushbutton
must match exactly.
Download from Www.Somanuals.com. All Manuals Search And Download.
Push Button Mounting Instructions
Note: Avoid mounting on metal surfaces, as it may result in a reduced
range of transmission. Do not mount in an area where exposed to direct
rain.
a. Removing the back cover
b. Replacing the back cover
1. Push buttons are typically mounted at the same height as the door knob or
handle (between 36" and 44" above the floor).
2. Before mounting, choose a mounting location that is not farther than 150
feet from the chime unit location.
Download from Www.Somanuals.com. All Manuals Search And Download.
Not farther than 150 feet
Place push button where you would like to mount and test operation with
the chime as close to it’s final location as possible. If it works, mount
button here. If it does not work, see TROUBLESHOOTING.
3.
Use back cover of push button as a template to mark two screw holes.
4.
5.
6.
Drill two holes with 1/16” drill in marked locations.
Secure back cover to the mounting surface with the 3x20mm screws.
Press front housing onto back cover.
Download from Www.Somanuals.com. All Manuals Search And Download.
7.
Test Operations, if chime does not work, see TROUBLESHOOTING.
Chime Unit Mounting Instructions
Note: Avoid mounting on metal surfaces, as it may result in a reduced
range of transmission.
1.
2.
3.
4.
5.
Select chime mounting location.
Use the supplied chime template to mark mounting holes.
Drill 5/32” holes at marked locations.
Insert supplied wall anchors into the holes.
Insert the 4/20mm screws into the anchors, setting the screw heads
extending about 1/4" from mounting surface.
6.
Place the chime unit’s keyhole slots over the screws and press down on
the chime unit to secure it.
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
1.
Slide power switch to “On” to turn on the chime.
2.
Gently press transmitter button to sound chime.
Troubleshooting
Chime doesn't work:
1.
2.
Make sure push button switch is depressed and held for at least 1 second.
Make sure house code switches 1-4 on chime and push button match
exactly.
3.
4.
5.
6.
Verify battery orientation in push button.
Try fresh batteries.
Make sure chime is not farther than 150 feet away from push button.
Ensure push button is not mounted on metal, near metal studs, or near the
Floor.
7.
Try a new location for the chime.
Functional range may be adversely affected by one or more of the following
factors: weather, radio frequency interference, low transmitter battery and
obstructions between the transmitter and receiver.
This device complies with Part 15 of the FCC rules. Operation is subject to the
following conditions:
1. This device may not cause harmful interference, and
2. This device must accept interference received, including any interference that
may cause undesired operation.
Download from Www.Somanuals.com. All Manuals Search And Download.
For technical support contact Jasco Products Company at 1-800-654-8483
Made in China
Hecho en China
is a trademark of
General Electric Company
and is used under license to
Jasco Products Company LLC,
10 E. Memorial Road,
Oklahoma City, OK 73114.
Rev. 4-07
19208
Download from Www.Somanuals.com. All Manuals Search And Download.
|