User / Installation Manual
Marine HD Widescreen
LED Television With DVD
MS-TV190LED, MS-TV220LED
FUSION Electronics New Zealand
FUSION Electronics Australia
FUSION Electronics Europe
FUSION Electronics USA
Ph: +64 9 369 2900
Ph: +61 1300 736 012
Ph: +31 76 572 3632
Ph: +1 623 580 9000
Download from Www.Somanuals.com. All Manuals Search And Download.
PVR File System
DVD
(Only for DTV source)
The PVR File System Menu Description
SELECT DISK: Select the PVR file system disk
DVD Setup Menu
Contents
Check PVR File System: Check the disk file format.
USB Disk: Display the USB Disk activation status, “PASS” flag is activation
Format: Format the USB device, create PVR file system format on the USB device
Time Shift Size: Show the TSR capacity information
Installation
2
Speed: Read and write speed.
Connections
3
Free Record Limit: Set the recording set-up time, unit is hours.
Antenna Connection
Basic Operation
Control Description
Remote Control
Menu Operation
EPG (Electronic Program Guide)
Source Selection
Channel
3
General Setup Page:
TV Display: Select the display aspect ratio from:
4
Digital Video Record
»
»
»
Normal / PS: Pan & Scan (4:3)
Normal /LB: Letterbox
»
Insert a USB device and enter the PVR File System page.
4
»
Select Check PVR File System, if USB device not previously formatted the system will
Wide: Widescreen (16:9)
5
automatically prompt USB disk formatting.
OSD Lang: Select the OSD Language (English is the default).
»
»
The size of the USB device affects the recording time available.
6
Screen Saver: Whether the screen saver is displayed after 3mins of inactivity.
Last Memory: Whether the DVD Player will remember the last position on a previous disc.
To record a DTV program press the
button. The recording will continue until
6
the Stop button is pressed or the USB device is full.
»
»
»
Press the button to shrink the on-screen information.
6
S pea k er s etup p a ge
Pressing the REC MENU button will open the recorded program page.
7
Recorded Programs can be viewed or deleted.
Picture
8
Important Recording Information
Time
9
»
The USB device must be at least 1 GB.
Sound
10
10
11
11
12
12
13
13
Speaker Setup Page:
»
When formatting a USB device all contents will be deleted. Formatting will fail if
the USB device contains a virus or any other defect.
Downmix: Select the downmix for SPDIF out.
Options
»
»
PVR function is only available in DTV source
Lock
USB device must be compatible USB 2.0 HS specification.
Media Play Function (DMP)
PVR File System
DVD
Specifications
Troubleshooting
Preference Page:
TV Type: Select the colour type from PAL, Auto, or NTSC.
Audio: Select the llanguage for the audio track on the disc (English is the default).
Subtitles: Select the lannguage for the subtitles on the disc (English is the default).
Disc Menu: Select the DVD Menu language (English is the default).
Parental: Select the Parental level allowed (Adult is the default). You will be asked for a
password to change (123456).
Password: Change the Parental password.
Default: Reset DVD Setup to factory default settings.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Lock
Media Play Function (DMP)
Thank you very much for your purchase of this product. Please read this manual carefully and keep it safe for reference.
Press MENU button on the remote and ◄/► use to cycle to LOCK page:
Note: All options are initially greyed out until password is entered (see below)
Access media files (Photo’s, Music, Movie’s and Text) via the TV’s USB port.
Please use the power cord designated for the product. When an extension cord is required, use one with the correct power rating. The cord must be grounded. The product should be
installed on a flat surface to avoid tipping. Space should be maintained between the back of the product and the wall for proper ventilation. If you would like to mount the TV to the wall,
please see “Preparing the LCD for Wall Mounting” below for additional information. Avoid installing the product in the kitchen, bathroom or other places with high humidity.
Press MEDIA button on the remote.
Lock System:
Set TV system time settings
Picture:
Supported picture formats include .jpg/jpeg and .gif
The image should be no bigger than 3000 x 3000 pixels.
Preparing Your LCD TV For Wall Mounting
The HDTV can either be kept on the stand or mounted to the wall for viewing. If you choose
to mount the HDTV to the wall, please follow the instructions below .
Installing the LCD TV Base Assembly
If you choose to mount the HDTV on the supplied base, please follow the instructions
below .
»
»
Select Lock System
Enter factory default password (0000)
»
»
Unplug all the cables and cords from your LCD TV.
»
»
Unplug all the cables and cords from your LCD TV.
Place the LCD TV face down on a soft and flat surface (blanket, foam, cloth, etc) to
prevent any damage to the display.
Place the LCD TV face down on a soft and flat surface (blanket, foam, cloth, etc) to
Set Password:
prevent any damage to the display.
Connect the base support to the metal axle from the rear using 2 of the supplied
4x10 screws.
»
From the LOCK menu select SET PASSWORD
»
»
Remove the stand screws allowing the stand to be removed.
»
»
Change password from factory default (above):
The mounting bracket is made up of two parts - the wall bracket and the TV
bracket. Attach the TV bracket to the TV via the included screws.
Block Program:
»
»
Using the supplied mounting template, mark the location for the mounting bracket.
Attach the wall bracket to the wall with appropriate screws. Ensure the wall is
»
»
Select Photo source
»
From the LOCK menu select Block Program.
suitable to hold the weight of the TV.
Use ◄ or ► to select disk and press ENTER to view photo list
»
Select channels to block and require password to watch.
»
Slide the TV bracket into the wall bracket.
Parental Guidance:
»
From the LOCK menu select Parent Guidance.
»
Secure the base support using the final 4x10 screw through the bottom of the
»
Select age restriction
base support.
»
»
»
Select the desired Photo/s
Press PLAY to view
Important Notes
RESET: Like any product controlled by microprocessors this TV may hang or become
unresponsive, in the unlikely event this occurs simple disconnect the power and reconnect
after 10 seconds.
Press EXIT to remove OSD
Music:
Supported music formats include .mp3
REMOTE: To prevent leakage which may result in bodily harm or damage to the remote:
1. Install AAA batteries correctly, and make sure polarities are correctly aligned with the
battery compartment markings.
2. Do not mix batteries (OLD and NEW or CARBON and ALKALINE ,etc)
3. Remove batteries when the remote is not used for a long time.
»
»
»
»
»
Select Music source
Use ◄ or ► to select disk and press ENTER to view music list
Select the desired music track/s
Press PLAY to begin playback
My music, movie or image files do not display?
Due to the large variation of file sizes, compression formats and codec available, playback
of all files cannot be guaranteed.
Press EXIT to remove OSD
I cannot record onto my USB flash drive?
FAT 32 formatted flash drive is required.
»
Affix the base to the base support and secure with 2 of the supplied 3x8 screws.
Movie:
Supported movie formats include .mpg, .vob, .avi, and .mp4
The maximum matrix is below MPEG2 MA/ML.
Time Shift functionality does work work?
FAT 32 formatted flash drive is required.
»
»
»
»
»
Select Movie source
Warning! Do not keep images on the screen for a long time
To prevent the screen from burn in, do not leave static images including menu screens
displayed for a period of time. Burn in is not covered under warranty provision.
Use ◄ or ► to select disk and press ENTER to view movie list
Select the desired movie.
ATTENTION: Do not try to update the TV unless directed by a service technician.
Product misconfigured by an incorrect update is not covered under warranty.
Press PLAY to begin playback
Press EXIT to remove OSD
Text:
Supported text format is .txt
»
»
»
»
»
Select Text source
Use ◄ or ► to select disk and press ENTER to view text list
Select the desired text.
PUBLISHED BY FUSION ELECTRONICS LIMITED. © Copyright 2010 by FUSION Electronics Limited. All rights reserved. Specifications and design are subject to change without notice.
YOU CAN HELP PROTECT THE ENVIRONMENT Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal centre. v3.2
Press PLAY to view text file
Press EXIT to remove OSD
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound
Options
Connections
Side Connection Panel:
Press MENU button on the remote and ◄/► use to cycle to SOUND page below:
Press MENU button on the remote and ◄/► use to cycle to OPTION page below:
Bottom Connection Panel:
IN
OUT
AUDIO VIDEO
EAR
PHONE COAXIAL
OUT OUT
IN
L
IN
Y
HDMI 1
IN
12V DC
IN
RF
IN
HDMI 2
IN
USB 1
VGA
L
R
VIDEO
R
Y
PB
PR
USB 2
Video/Audio In:
Connect the VIDEO and AUDIO output jack of the DVD or VCR to the VIDEO/L/R IN jacks
Power:
Connect the AC power pack or 5M DC fly lead to the 12V DC IN connection on the TV.
using an AV cable (Yellow [Video], White and Red [left and right audio]).
Select the AV input source using the INPUT button on the remote.
USB 1:
Insert the USB flash drive into the USB slot on the TV.
RF IN:
Select the USB input source using the MEDIA or INPUT button on the remote.
Sound Mode:
Connect the antenna to the RF IN connection. Please refer to the Antenna Connection
»
Select Sound Mode
paragraph below.
OSD Language:
HDMI 1:
»
Press ◄ or ► to cycle through available sound modes:
Standard, Music, Movie, Sports and User.
Set current menu language
Connect the HDMI output of the accessory device to the HDMI input on the TV.
Y/Pb/Pr In:
Connect the Y Pb Pr output of the accessory device to the Y Pb Pr input on the TV.
Note: Treble and Bass can only be changed under User.
Select the HDMI input source using the INPUT button on the remote.
»
Select OSD Language
Connect the Audio output of the accessory device to the L/R IN input jacks on the TV
using the RCA cable.
VGA/Audio In:
Connect the RGB output of the PC to the VGA input on the TV.
Connect the PC audio output of the PC to the Audio input jack on the TV
Select the VGA input source using the INPUT button on the remote.
Audio Language:
Set audio language
Select the Y Pb Pr input source using the INPUT button on the remote.
»
»
Select Audio Language
HDMI 2:
Press ◄ or ► to cycle through available languages:
Connect the HDMI output of the accessory device to the HDMI input on the TV.
Video/Audio Out:
Connect the AUDIO output from the television to the AUX input of the device using the
supplied A/V cable (White and Red [left and right audio]).
Select the HDMI input source using the INPUT button on the remote.
Subtitle Language:
Set subtitle language
USB 2:
Insert the USB flash drive into the USB slot on the TV.
Connect the VIDEO output from the television to the Composite VIDEO input of the device
using the supplied A/V cable (Yellow [video]).
»
»
Select Subtitle Language
Press ◄ or ► to cycle through available languages:
Select the USB input source using the MEDIA or INPUT button on the remote.
NOTE: Video out functionality is only available through the DTV, ATV and AV sources.
Adjust Balance:
Video out will not work on HDMI, MEDIA, or Y Pb Pr.
»
From the SOUND menu select Balance
Hearing Impaired:
»
Select Hearing Impaired
Auto Volume:
Antenna Connection
»
Select ON or OFF
»
From the SOUND menu select Auto Volume.
To ensure good picture and sound, a Terrestrial TV antenna system needs to be
installed. For best reception, an outdoor antenna is recommended.
»
Select ON or OFF
PVR File System:
NOTE:
(Reference ‘PVR File System’ on following page)
•
•
•
Do not put the Coaxial cable close to the mains lead to avoid noise.
Do not place the Coaxial cable under the TV.
Additional equipment, cables and adapter plugs shown are not supplied with
this TV set.
SPDIF Mode:
»
From the SOUND menu select SPDIF MODE.
OSD Time Out:
»
Press ▲ or ▼ to cycle through available modes for SPDIF:
PCM, Auto, or Off.
•
•
To obtain optimum quality picture and sound, an Aerial, the correct cable (75 Ω
coaxial) and the correct terminating plug are required.
Your local dealer may be able to assist you in obtaining the correct Aerial system
for your particular area and the accessories required.
»
Select OSD Time Out
»
Select from OFF, or from 10S - 90S
Blue Screen:
»
Select Blue Screen
»
Select ON or OFF for whether a Blue Screen is displayed when there is no signal input.
(Except MEDIA and DVD)
Restore Factory Default:
»
Select Restore Factory Default to restore to initial settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Control Description
Time
Press MENU button on the remote and ◄/► use to cycle to TIME page below:
Off Time:
Set TV system to turn off automatically.
»
»
From the TIME menu select Off Time
»
»
»
»
»
»
»
Press CH- or CH+ to scan through channels.
Press V O L- or VOL+ to decrease or increase the sound level.
Press MENU to bring up the main menu screen.
Press SOURCE to select the input source.
Press ◄ or ► to select Off Time mode:
Off, Once, Every Day, Mon - Fri, Mon - Sat, Sat -Sun or Sunday
»
Set the Hour and Minute
Press to play/pause
Press to eject the disc when in DVD source only
Press POWER button to alternate between standby and ‘on’ modes.
Power
Volume +/-
Clock:
Set TV system time settings
To adjust the volume:
To operate the HDTV:
»
Press the VOL+ button to increase the volume.
»
»
Select Clock
»
»
»
Ensure you have connected the HDTV correctly and that power is supplied to the TV.
A RED LED indicates Standby Mode. A GREEN LED indicates the HDTV is ON.
»
Press the V O L- button to decrease the volume.
Press ◄ or ► to cycle through available clock settings:
Date, Month, Year, Hour and Minute.
Press the POWER button to power ON the television. The front LED will change from
On Time:
RED to GREEN to indicate that that HDTV has been turned ON.
Set TV system to turn on automatically.
Mute
»
Press the POWER button to power OFF the television. The front LED will change from
»
»
From the TIME menu select On Time
To mute the audio:
Press the MUTE button to mute the audio. (Note: This will not mute the line-level
audio output).
GREEN to RED to indicate that that HDTV has been turned OFF.
Press ◄ or ► to select On Time mode:
»
Off, Once, Every Day, Mon - Fri, Mon - Sat, Sat -Sun or Sunday
»
»
»
»
Set the Hour and Minute
»
»
The HDTV will indicate that it is in a mute state.
Select the input source
Press the MUTE button to un-mute the audio.
Channel +/-
If ATV or DTV source is selected, also select the program number
Select the Volume setting at turn on
»
»
Press the + button to change the channel/chapter up.
Press the - button to change the channel/chapter down.
Display
»
Press the DISPLAY button to preview the curent program number, current input mode,
or any relevent source information.
Numeric Keypad
Sleep Timer:
»
Press the DISPLAY button again to remove this information.
To directly select a channel or chapter number:
Press the required number from 0-9 on the keypad. It will directly change to the
choosen channel/chapter.
To select a 2-digit channel/chapter number, press the -/-- button followed by the
numbers you desire.
»
From the TIME menu select Sleep Timer
»
»
Select Sleep Timer setting:
Off, 10min, 20min, 30min, 60min, 90min, 120min, 180min or 240min
»
Auto Sleep:
»
From the TIME menu select Auto Sleep.
»
Select ON or OFF
Time Zone:
»
From the TIME menu select TIME ZONE.
»
Select your Time Zone
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Remote Control
POWER - Switch between Standby and On
Eject in DVD Source
Press MENU button on the remote and ◄/► use to cycle to PICTURE page below:
Aspect Ratio:
»
From the PICTURE menu select Aspect Ratio
MUTE - Press to mute the audio. Press again or press VOL+ to resume
»
Press ▲/▼ to select Aspect Ratio: Auto, 4:3 and Full.
NUMBER BUTTONS - Press 0-9 to select a TV channel directly when watching TV
The channel changes after 2 seconds or press ENTER button to change immediately
POWER
MUTE
Press to change the channel bit when watching TV
Return to the previously viewed program
2
5
1
4
3
VOL+/- - Press to increase or decrease volume
ASPECT - Select the screen aspect
6
9
7
8
0
AUDIO - Press to change the language of the audio in DTV or DVD source.
CH+/- - Press to change channel
-/--
▲/▼/◄/►/OK - Allows you to navigate the on-screen menus and adjust the
ASPECT
AUDIO
system settings to your preference
+
+
Picture Mode:
LCD MENU - Access the on-screen menu
DVD SETUP - DVD menu setup
CH
VOL
_
DISPLAY
_
»
Select Picture Mode
EXIT - Exit the menu or sub menu
INPUT - Select the TV source
»
Press ◄ or ► to cycle through available picture modes:
Standard, Mild, User and Dynamic.
Note: Contrast, Brightness, Color and Sharpness can only be changed under User.
Noise Reduction:
P.MODE - Select the picture mode
S.MODE - Select the audio mode
»
From the PICTURE menu select Noise Reduction
»
Press ▲/▼ to select Noise Reduction: Off, Low, Middle, and High.
DVD
SETUP
SLEEP - Set the TV to turn off after a specified time
LCD
MENU
FAV - Press to display favorite programs
FAV+ - Press to change favorite program
FAV- - Press to change favorite program
EPG - Press to display EPG information (Electronic Program Guide) (DTV only)
TEXT - Press to turn the Teletext On and Off
ANGLE - Press to choose a differrent angle (DVD)
HOLD - HOLD On or Off the current page display
ZOOM - Press to change the magnification.
TV/RADIO - Press to switch between DTV and radio programs (DTV Only)
SUBTITLE - Select subtitle language
EXIT
SLEEP
PMODE
FAV-
SMODE
INPUT
FAV
FAV+
EPG
TV/RADIO SUBTITLE
TEXT
HOLD
ZOOM
ANGLE
SUBPAGE
GOTO
SIZE
REVEAL
D.DISP
INDEX
D.MENU
TITLE
MEDIA
INDEX - Press to return to the index/initial page
D.MENU - Display the DVD menu
Color Temperature:
PROG
PBC
REPEAT
A-B
»
From the PICTURE menu select Color Temperature
SIZE - Change the size of display in Teletext mode
TITLE - Press to display Title information
REVEAL - Reveal or Hide the hidden words
D.DISP - Press to cycle the DVD disc information.
SUBPAGE - Display a sub-page of upper options
GOTO - Press to goto specific chapter in DVD
MEDIA - Access DMP menu
Screen:
Note: Only available in VGA Source
»
Press ◄ or ► to cycle through available color temperature modes:
Medium, User, Warm and Cool.
»
»
From the PICTURE menu select Screen
Note: Red, Green, and Blue can only be changed under User.
Press ▲/▼ to select Screen Options:
Auto Adjust, Horizontal Position, Vertical Position, Size and Phase.
►II - Play/pause
◄◄/►► - Play fast backward/forward
REC - Press to record the program immediately
■ - Stop playing
I◄◄/►►I - Play previous/next media file
PROG - Use in Teletext, DTV and ATV modes
PBC - VCD scan
REPEAT - Press to change the playing mode
A-B - Repeat the segment between A and B
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Operation
Menu Operation
Source Selection
Channel
This section explores the menus of your TV. Each menu is outlined and detailed to help
you get the most from your TV.
To access the input source’s press INPUT on the remote.
Press MENU button on the remote to enter the CHANNEL page below:
ATV Manual Tuning
Input source is ATV, operate as below:
»
»
Press ▲/▼ to move the cursor
Press OK to confirm your selection
To access the main menu page press MENU on the remote.
Press ◄/► to cycle through the seven main functions below:
»
»
»
»
»
From the CHANNEL menu select ATV Manual Tuning
Select Storage To 1 and enter channel that you wish to store program to (1-100).
Select System DK and select TV system.
»
»
»
»
»
»
CHANNEL
PICTURE
SOUND
TIME
Select Search to start ATV Manual Tuning. To interrupt press MENU or Exit
Select Fine Tune and use ◄/► to fine tune program
OPTION
LOCK
Auto Tuning:
EPG (Electronic Program Guide)
ATV and DTV auto program, operate as below:
Only available for DTV source.
»
»
»
Select Auto Tuning and press OK .
To return to previous page press MENU or Exit
»
»
Press EPG on remote to enter menu
To interrupt tuning, press MENU or Exit. The below confirmation screen will appear.
Press ◄ to confirm exit, or ► to continue tuning.
Follow on screen instructions for EPG control and navigation.
Program Edit
»
From the CHANNEL menu select Program Edit
»
Select the program using ▲/▼ and press the following:
Delete Program: Delete selected program
DTV Manual Tuning
Input source is DTV, operate as below:
Rename Program: Edit program name (DTV Only)
Reorder Program: Select first program and then select the second program.
The two programs will swap order.
»
From the CHANNEL menu select
DTV Manual Tuning
Skip Program: Select program to be skipped.
»
»
Select channel number by pressing ◄/►
Press ENTER to search
Favourite: Press the remote
to favourite list.
FAV button to activate. Select program to add
Signal Information
Display’s the signal information of current program.
»
From the CHANNEL menu select Signal Information
Download from Www.Somanuals.com. All Manuals Search And Download.
|