P/N134447700(0407)
Download from Www.Somanuals.com. All Manuals Search And Download.
This Owner's Guide provides general
operatinginstructionsforyourdryer.
It also contains information about
features for several other models.
Your dryer may not have every
feature included.
Protect Children
Do not allow children to play on or in the dryer. Close supervision of
children is necessary when the dryer is used near children. As children grow, teach
them the proper, safe use of all appliances.
Destroy the carton, plastic bag and other packing materials after the
dryer is unpacked. Children might use them for play. Cartons covered with rugs,
bedspreads or plastic sheets can become airtight chambers.
Use the dryer only as instructed in
this Owner's Guide and the
Operating Instructions card
included with your dryer.
Keep laundry products out of children's reach. To prevent personal
injury, observe all warnings on product labels.
Before the dryer is removed from service or discarded, remove the
dryer door to prevent accidental entrapment.
Avoid fire hazard or
electricalshock. Donotuseanadaptor
plug or extension cord or remove
groundingprongfromelectricalpower
cord. Failuretofollowthiswarningcan
cause serious injury, fire or death.
Failure to comply with these warnings could result in serious personal injuries.
Prevent Injury
To prevent shock hazard and assure stability during operation, the
dryer must be installed and electrically grounded by a qualified service person in
accordance with local codes. Installation instructions are packed in the dryer for the
installer's reference. Refer to INSTALLATION INSTRUCTIONS for detailed grounding
procedures. If the dryer is moved to a new location, have it checked and reinstalled
by a qualified service person.
ELECTRIC DRYERS:
14-30R
DRYER
FUSED30AMP
120/240VOR
120/208V
To prevent personal injury or damage to the dryer, the electrical
powercordmustbepluggedintoaproperlygroundedsystem.Thethirdgrounding
prong must never be removed. Never ground the dryer to a gas pipe. Do not
use an extension cord or an adaptor plug.
WALL
DRYER
SERVICECORD
RECEPTACLE
CORRECT
Use this way ONLY
ALWAYS disconnect the dryer from the electrical supply before
attempting any service or cleaning. Failure to do so can result in electrical shock or
injury.
GAS DRYERS:
Grounding type
wall receptacle
Do not use any type spray cleanser when cleaning dryer interior.
Hazardous fumes or electrical shock could occur.
Do not under
any circumstances
cut, remove,
To prevent injury, do not reach into the dryer if the drum is moving.
Wait until the dryer has stopped completely before reaching into the drum.
or bypass
the grounding prong
from this plug.
To prevent injury and damage to the dryer:
•
All repairs and servicing must be performed by an authorized servicer
unless specifically recommended in this Owner's Guide. Use only authorized
factoryparts.
Power supply
cord with 3-prong
grounding plug
•
•
Do not tamper with controls.
Do not install or store the dryer where it will be exposed to the weather.
CORRECT
Use this way ONLY
A thermal limiter switch automatically turns off the motor in the unlikely event
ofanoverheatedsituation(electricdryersonly).Aservicetechnicianmustreplacethe
thermal limiter switch after correcting the fault.
Note: The instructions appearing in this
Owner's Guide are not meant to cover
every possible condition and situation
that may occur. Common sense and
caution must be practiced when
installing, operating and maintaining
any appliance.
Failure to comply with these warnings could result in serious personal injuries.
SAVE THESE INSTRUCTIONS
3
Download from Www.Somanuals.com. All Manuals Search And Download.
• Follow the guidelines below for preparing the load for drying.
Drying Procedures
• Read the Operating Instructions card for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions, pages 2-3, before operating this dryer.
1. Prepare items for drying.
•
Dry items of similar fabric, weight and construction in the same load.
•
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
•
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand
sashes to prevent snagging and tangling.
•
•
If possible, turn pockets inside out for even drying.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
Followfabriccarelabelinstructions.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
Placesmallitemsinameshbag.
If desired, add a dryer fabric softener sheet.
4. Close the dryer door and set dryer controls (some models).
See Operating Instructions card for your specific model controls.
5. Turn cycle selector clockwise to the desired setting.
6. Start the dryer.
•
Push Start button for 2 seconds.
•
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer
will always stop when the door is opened. Allow the drum to come to a
complete stop before reaching inside.
•
•
To restart dryer, close the door, then push the START button for 2 seconds.
The dryer will not start if the cycle selector is in the OFF position.
7. When the cycle ends, remove items immediately and hang
Filldryerdrum1/3to1/2full.
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle Signal Control (some models)
Features
When the Cycle Signal Control is ON, a signal will sound at the end of each cycle
andduringthePressSaversetting(somemodels).Thevolumeisadjustableonsome
models.
Drum Light (some models)
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum
during loading and unloading. Closing the door turns off the light.
Reversible Dryer Door
Your dryer is equipped with a reversible door. The door can be hinged on the right
or left side. Refer to the INSTALLATION INSTRUCTIONS for directions on changing
the door.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insert drying rack into the dryer drum. Place the front bar under the lip of the
lint screen opening.
3. Place items to be dried on top of the rack. Weight should not exceed 10 lbs.
Leavespacebetweenitems, butdonotletitemshangoverthesidesorthrough
the grids. Do not tumble other items when using the drying rack.
4. Selectatimeddrysettingbestsuitedforitemsbeingdried.UseonlytheAirFluff
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-
like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
is not in place, tumbling items could enter the exhaust system and cause
damage to the dryer.
Place the front bar under
the lip of the lint screen opening.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PREVENTIVE MEASURES
• Add a few bath towels to small loads for
proper tumbling.
PROBLEM
Greasy, oily
stains
POSSIBLE CAUSES
• Fabric softener sheet.
SOLUTIONS
• Rub fabric softener stains with bar soap.
Rinse and rewash.
• Some "silk-like" fabrics should be air dried.
• Use proper drying temperature.
• Place fabric softener sheet on top of load
before starting the dryer.
Lint
• Do not overload dryer.
• Use fabric softener in washer or dryer to
reduce static electricity.
• Remove items when they are slightly damp
to avoid overdrying.
• Check that lint screen is clean and in place.
• Overloading.
• Overdrying causes static
electricity.
• Lint screen not clean
when cycle began.
• Lint is attached to "pills."
• Reduce load size and rewash using liquid
fabric softener in the final rinse.
• Or, add a fabric softener sheet and
tumble without heat.
• Use lint brush or roller to remove lint.
Pilling
• Use a lint brush or shaver to remove pills.
• Use fabric softener to lubricate fibers.
• When ironing, use spray starch or fabric
finish on collars and cuffs.
• Pilling is normal with
synthetic and permanent
press fabrics. This is due
to abrasion from normal
wear.
(Fibers break
off, ball up and
cling to fabric.)
• Turn items inside out to reduce abrasion.
Shrinking
Wrinkling
• Irreversible condition.
• Follow fabric care label directions.
• If shrinking is a concern, check load often.
• Remove items while slightly damp and
hang or lay flat to complete drying.
• Block knits into shape.
• Overdrying.
• Reduce load size and tumble at medium
or low heat for 5-10 minutes.
• Remove items immediately. Hang or fold.
• Do not overload dryer.
• Remove items as soon as cycle ends.
• Overloading.
• Leaving items in dryer
after cycle ends.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
To reduce risk of fire or serious injury to persons or property, comply
with the basic warnings listed in Important Safety Instructions, pages 2-3, and
those listed below.
Care and Cleaning
•
•
Before cleaning the dryer interior, unplug the electrical power cordto avoid
electrical shock hazards.
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside
•
Cleanthelintscreenaftereveryload.Lintbuild-upinthescreenrestrictsairflow,
whichcauseslongerdryingtimes.Thescreenislocatedatthebottomofthedoor
opening.Removebypullingstraightup.Removethelintandreplacethescreen.
•
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Clean lint screen after every load.
Every 18 months an authorized servicer should clean the dryer cabinet interior
and exhaust duct. These areas can collect lint and dust over time. An excessive
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.
Outside
•
•
•
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.
If the cabinet becomes stained, clean with diluted chlorine bleach [1/2 cup
(120 ml) in 1 quart (.95 liter) water]. Rinse several times with clear water.
Removeglueresiduefromtapeorlabelswithamixtureofwarmwaterandmild
detergent. Or, touch residue with the sticky side of the tape or label.
Before moving the dryer, place a strip of cardboard or thin fiberboard under
the front leveling legs to prevent damage to floor.
Do not store or place laundry products on
top of dryer at any time. They can damage
the finish or controls.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Before calling for service, review this list. It may save both time and expense. The list includes
common occurrences that are not the result of defective workmanship or materials in this dryer.
Avoid Service
Checklist
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
Electrical power cord is not securely plugged
in or plug may be loose.
Make sure the plug fits tightly in wall outlet.
Dryer does not start.
House fuse blown or circuit breaker tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer is on
a separate circuit.
Thermal limiter tripped.
Call authorized service person for replacement.
Replace fuse.
There are 2 house fuses in the dryer circuit. If
1 of the 2 fuses is blown, the drum may turn
but the heater will not operate.
Dryer runs but won't heat.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See INSTALLATION
INSTRUCTIONS for procedure.
Dryer does not have enough air supply to
support the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has been
a utility interruption of natural gas (gas
models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Lint screen is clogged with lint.
Makesurealllinthasbeenremovedfromthedryerlintscreen
before starting each cycle.
Drying cycle takes too long,
outsideofthedryerfeelstoo
hot or smells hot.
Exhaust duct requirements have not been
met.
Exhaust duct must be at least 4 inches in diameter and made
of rigid or flexible metal.
When in place, the duct must have no more than two 90°
bends and must not exceed length listed in INSTALLATION
INSTRUCTIONS.
Electricdryerisconnectedtoa208voltcircuit.
Drying procedures have not been followed.
Drying time will be 20% longer than drying on a 240 volt
circuit.
See Drying Procedures, page 4.
Outside exhaust hood or exhaust duct may
be clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
Dryer is overloaded.
Do not overload. See Drying Procedures, page 4.
Remove items as soon as cycle ends.
See Drying Procedures, page 4.
Excessive wrinkling.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
Foreign objects such as coins, pins, clips or
buttons are inside the dryer.
Always remove foreign objects from pockets before
laundering. Remove objects from drum and restart dryer.
Scratchingorchippingofthe
drumfinish.
Permanently attached items such as belt
buckles, zippers and fasteners may be hitting
the inside of the drum.
It may be necessary to baste a scrap of material securely
around ornaments before drying to prevent scratching and
damage to the dryer.
Drumdamagecausedbyforeignobjectsorpermanently
attached items is not covered by the warranty.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
FRIGIDAIRE DRYER WARRANTY
Your Frigidaire product is protected by this warranty
FRIGIDAIRE,THROUGHITSAUTHORIZED
SERVICERS, WILL:
THECONSUMERWILLBE
RESPONSIBLEFOR:
WARRANTY
PERIOD
FULLONE-YEAR
WARRANTY
Pay all costs for repairing or replacing any parts of this appliance Costs of service calls that are listed under IMPORTANT
which prove to be defective in materials or workmanship. RESPONSIBILITIESOFTHECONSUMER.*
One year from original
purchase date.
LIMITEDWARRANTY
(Applicabletothe
State of Alaska)
All of the provisions of the full warranty above and the exclusions Costsofthetechnician'straveltothehomeandanycosts
Time period listed above.
listed below apply.
for pick up and delivery of the appliance required
because of service.
Your appliance is warranted by Frigidaire Home Products, a division of White Consolidated Industries, Inc. We authorize no person to change or add to any
of our obligations under this warranty. Our obligations for service and parts under this warranty must be performed by Frigidaire or an authorized Frigidaire
servicer.
*IMPORTANT
RESPONSIBILITIES
OF THE CONSUMER
This warranty applies only to products in ordinary household use, and the consumer is responsible for the items listed
below:
1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance
with all local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose connections
or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves, etc., which are not
a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
EXCLUSIONS
This warranty does not cover the following:
1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM
ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
Note: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation or exclusion
may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in ordinary household
use. The consumer shall pay for such service calls.
3. Damages caused by services performed by servicers other than Frigidaire or its authorized servicers; use of parts other than
genuine Frigidaire Home Products parts; obtained from persons other than such servicers; or external causes such as abuse,
misuse, inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the warranty period
should service be required. If service is performed, it is in your best interest to obtain and keep all receipts. This written warranty
gives you specific legal rights. You may also have other rights that vary from state to state. Service under this warranty must be
obtained by contacting Frigidaire Home Products:
IF YOU NEED
SERVICE
800 • 944 • 9044
Frigidaire Home Products
P.O. Box 212378
Augusta, GA 30917
Product features or specifications as described or illustrated are subject to change without notice. All warranties are made by White
Consolidated Industries, Inc. This warranty applies only in the 50 states of the U.S.A. and Puerto Rico.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
To avoid unnecessary cost and inconvenience, make a few simple checks before
calling for service. Common occurrences and their solutions can be found in the
Avoid Service Checklist. Be sure you have followed the instructions in this manual.
Service Information
(Canada)
If you are unable to locate the cause of a problem, call for service. Insist on factory
service by an authorized ELECTROLUX PARTS AND SERVICE depot.
ELECTROLUXPARTSANDSERVICE
All Frigidaire appliances are backed by ELECTROLUX PARTS AND SERVICE, one of
Canada's largest parts and service networks.
The Frigidaire reputation means you can enjoy complete professional service from
one of our hundreds of trained technicians across the country. Ask your Frigidaire
dealer for details about the Extended Service Plan offered by ELECTROLUX PARTS
AND SERVICE to all purchasers of Frigidaire appliances in Canada.
PARTSANDSERVICE:
ELECTROLUX HOME PRODUCTS CANADA
6150 McLaughlin Road, Unit#1
Mississauga,Ontario
L5R 4C2
Tel.:
Fax:
(905)568-3433
(905)568-3542
Place the name, address and telephone number of your service depot in the
spaces below.
Product and feature specifications as described or illustrated are subject to
change without notice.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY (CANADA)
AUTOMATIC WASHERS AND DRYERS
Forserviceunderthiswarranty,contactyourlocaldealer/
retailer,authorizedFRIGIDAIREPARTSAND SERVICEdepot,or:
PARTSANDSERVICE:
WARRANTOR:
ELECTROLUX HOME PRODUCTS CANADA
6150 McLaughlin Road, Unit#1
Mississauga,Ontario
ELECTROLUX HOME PRODUCTS CANADA
6150 McLaughlin Road, Unit#1
Mississauga,Ontario
L5R 4C2
L5R 4C2
Tel.:
Fax:
(905)568-3433
(905)568-3542
WARRANTOR WILL THROUGH ITS AUTHORIZED
SERVICEDEPOT:
WARRANTYPERIOD:
Pay all costs to repair or replace any defective parts.
Forthefirstyearafterpurchasebytheoriginalconsumer/
owner:
Payallcosts ofadefectivepolypropylenewasherbasket.
For twenty five years after purchase by the original
consumer/owner:
Pay all costs (excluding labour to install) to replace any
defective transmission parts.
Top load automatic washers only: transmission for the
secondthroughfifthyearafterpurchasebytheoriginal
consumer/owner:
WARRANTYAPPLIESTO:
a) Products purchased and installed in Canada for personal single family household use.
b) Defects resulting or arising out of the manufacturing process.
c) Products bearing legible manufacturer's model and serial numbers.
d) Replacement parts only for the remainder of the original warranty.
WARRANTY DOES NOT APPLY TO:
a) Transportationdamage.
b) Supply and replacement of porcelain, fuses, glass and light bulbs.
c) Parts and service supplied or obtained from other than FRIGIDAIRE PARTS AND SERVICE or FRIGIDAIRE PARTS AND SERVICE
authorizeddepots.
d) Damage or failure as the result of abuse, improper or commercial use.
CONSUMER/OWNERRESPONSIBILITY:
a) Toprovideproofoftheoriginaldateofpurchasebymeansofabillofsaleorpaymentrecordverifyingpurchasedate.
b) To pay all costs to make the appliance readily accessible for service.
c) To ensure proper power supply and connection of the appliance to same.
d) Proper installation, control setting and care of finish.
Thiswarrantyisinadditiontoanystatutorywarrantiescontainedinanyapplicablelegislation. Thetermsandconditions
of this warranty are not intended to exclude or limit your rights under those statutes. The warrantor however reserves
therighttochargetransportationandtravellingcostsfordistancesinexcessof48kilometres(30miles)fromthenearest
FRIGIDAIRE PARTS AND SERVICE authorized service depot.
This warranty plus the statutory warranties mentioned are the only warranties given to the consumer/owner for this
product.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
|