QuickStart Guide
LED
State
Description
Green
The module is properly inserted in the FortiGate unit.
FortiGate ASM-FX2
FGT ACT
Off
The module is not receiving power from the FortiGate unit.
Blue
Ejection latch open. The module is ready for removal.
HS
Flashing
Ejection latch opened during system operation.
LED currently not in use.
BYPASS
FORTIGATE
FGT ACT
OOS
IPM
HS
OOS
BYPASS
Green
Off
The module is properly inserted in the FortiGate unit.
The module is not receiving power from the FortiGate unit.
The correct cable is in use and the connected equipment has power.
IPM
1
2
1
Green
Ports
1 and 2
Flashing Green Network activity on the interface.
2
Green
Off
Bypass network activity at this interface.
BYPASS
ASM-FX2
Normal status or not receiving power from the FortiGate unit.
Visit these links for more information and documentation for your Fortinet product.
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class A Part 15 CSA/CUS
01-30006-0473-20090120
20 January 2009
Package Contents
Connector
Type
Speed
Protocol Description
Ports 1 and 2
SERDES compatible SX fiber
1000 Base-SX
Ethernet Fiber network connections.
QuickStart Guide
BYPASS
FORTIGATE
FGT ACT
BYPASS
FORTIGATE
FGT ACT
HS
OOS
HS
OOS
BYPASS
BYPASS
1
IPM
1
2
IPM
1
2
1
2
ASM-FX2
2
Copyright 2008 Fortinet Incorporated. All rights reserved.
Trademarks
ASM-FX2
Installing the AMC Module
The module should glide smoothly into the chassis. If you encounter any resistance while
sliding the module in, the module could be aligned incorrectly. Pull the module back out
and try inserting it again.
It is important to carefully seat the FortiGate ASM-FX2 module all the way into the chassis.
Only then will the FortiGate ASM-FX2 module power-on.
To complete this procedure, you need:
7. Press the hot swap latch to lock in the module.
• A FortiGate ASM-FX2 module.
• A FortiGate chassis with an empty AMC single-width (SW) opening.
• To avoid any electrostatic discharge, install in a static free area.
8. Power on the FortiGate unit. The hot swap (HS) LED turns on and then begins flashing.
ASM-FX2 module ports
AMC/1
IP:
____.____.____.____
AMC/2
IP:
____.____.____.____
FortiGate ASM-FX2 modules are not hot swappable. The procedure for inserting the
FortiGate ASM-FX2 module into a FortiGate chassis slot requires the FortiGate unit to be
powered off.
Netmask:
____.____.____.____
Netmask:
____.____.____.____
Removing the AMC module
To avoid any electrostatic discharge (ESD) when handling FortiGate ASM-FX2 modules,
install in a static free area.
Should you need to remove the ASM-FX2, shut down the FortiGate unit using proper shut
down procedures.
To insert a FortiGate ASM-FX2 module into a FortiGate chassis
To remove the ASM-FX2 module
1. Ensure the FortiGate unit is powered off before proceeding.
2. Remove the panel block on the FortiGate unit using the hot swap latch.
3. Pull the latch on the ASM-FX2 module to the extended position.
1. Ensure the FortiGate unit is powered off before proceeding.
2. To avoid any electrostatic discharge (ESD) when handling ASM-FX2 module, uninstall in
a static free area.
4. Insert the ASM-FX2 module into the empty slot in the chassis. Ensure the Fortinet logo
3. Pull the hot swap latch on the right-hand side of the module to the extended position to
unlock the module from the FortiGate unit.
is right-side up. It should be on the lower-right corner of the module.
5. Carefully guide the module into the chassis.
4. Gently pull the hot swap latch to remove the module.
6. Insert the module by applying moderate force to the front faceplate near the upper edge
to slide the module into the slot.
Connecting the Module
CLI Commands
When properly inserted into the FortiGate unit, the interfaces of the ASM-FX2 appear in the
interface list by going to System > Network > Interface.
To enable or disable bypass mode, press the Bypass FortiGate button, or use the following
CLI commands. For more information on these commands go to htp://kc.fortinet.com.
You can add policies, zones and so on as you would with other FortiGate interfaces.
exec amc bypass-mode <enable | disable>
Enable the bridging feature of the module using the Command Line Interface.
Download from Www.Somanuals.com. All Manuals Search And Download.
|