Flowtron Outdoor Products Insect Control Equipment MT 350 User Manual |
WARRANTY
MT-350
Trouble Shooting Chart
Symptom
Probable Cause
No power at outlet
Remedy
Check for electrical power at outlet.
Mode lights on control panel do
not light when “MODE” switch is
depressed.
Unit not properly connected to its power pack. Check plug connections between unit and power pack low voltage cord.
Green lights on control panel
are flashing.
Lack of propane.
Refill propane tank.
Open tank valve.
Propane tank valve closed.
Regulator coupling not properly attached.
Lack of propane
Check propane regulator coupling for proper engagement and/or leaks.
Same as for “green lights flashing”.
The fan does not run
continuously after the unit has
been on for at least 10 minutes.
Start cycle malfunction.
Press “Reset” and restart in 24/7 mode.
The unit does not start up at
dusk when in an automatic
mode.
Unit has not sensed dusk or night for a
full 10 minutes.
Wait for 10 minutes of darkness.
Ambient temperature is below
55-60ºF.
Unit will start automatically if temperature rises above 55º F
within 2 hours of dusk.
Ambient light level is too high.
Shield unit from extraneous light.
Not catching mosquitoes when
the fan is running, the valve is
pulsing and the green lights on
the control panel are not
flashing.
Funnel end is not over catch tray
nozzle opening.
Engage the funnel end with the catch tray nozzle opening.
Funnel clogged with insect debris.
Trap is not located in a productive site.
Windy, cool or stormy weather.
Clean funnel. See page 7.
Move trap to a new site. See placement guidelines in the owner’s manual.
Wait for conditions more to the mosquito’s liking.
Current mosquito population not readily
attracted to CO2 + Octenol.
Notably the day flying Asian tiger Mosquito. Operate the trap with the
octenol cartridge removed.
Any problems you encounter that are not corrected by the action recommended in this chart should be referred to the Flowtron Service Department
Accessories
Accessories are available at your local retail outlet or by calling
Flowtron Parts Department at 1-800-343-3280.
OWNER’S MANUAL
IMPORTANT
Mosquito Attractant:
Extension Cord – EC-50
Read this manual completely before
installing or operating your new
Mosquito PowerTrap™.
Octenol Cartridge – MA 1000
Makes your Mosquito PowerTrap
more effective in attracting mosquitoes
and biting flies.
50 foot low voltage extension cord.
Allows placement of the Mosquito
PowerTrap an additional 50 feet away
from the power source.
Look for this
symbol to point
out important safety precautions.
Flowtron Outdoor Products, 15 Highland Avenue, Malden, MA 02148 • 1-800-343-3280
557-9657
Download from Www.Somanuals.com. All Manuals Search And Download.
Tank Support
Strap
Connect Propane Regulator
Placement
Assembly
Tank Stand
Rules for Safe Use
(MT-300 series only)
1. Remove the plastic dust cover from your propane
tank valve.
Your Mosquito PowerTrap is site specific and place-
ment is critical for successful results. To properly lo-
cate your unit in your yard, read the accompanying
booklet “the Fine Art of Trapping Mosquitoes”
and follow its guidelines regarding trap placement,
1. Insert tank support strap
into openings in tank
stand as shown.
1. Use outdoors only. Install the unit a
minimum of ten feet from
2. Screw the propane regulator coupling located on
the end of the propane hose onto the tank valve by
turning the black threaded coupling clockwise until
tight. Hand tighten only. See Illustration 4.
See Figure A.
buildings and other structures.
Openings
Figure A
Your Flowrtron Mosquito PowerTrap emits a plume of
octenol-enhanced carbon dioxide which mosquitoes
follow in their search for a blood meal. Mosquitoes fly
up-wind toward the source of the plume in their at-
tempt to locate a host. Since the direction of the
plume is dependent upon the direction of the wind,
your unit should be positioned so it’s
On the underside of the
tank stand, loosen the
two hex nuts located on
the screws which extend
from the sides of the
base plate. Place the
slots at the ends of the
tank support strap over
the screws and secure
by tightening the two
nuts. See Figure B.
Note: Gas will not flow unless connection is tight.
Tighten by hand only.
Using a wrench or
other tool could
damage the regulator
Base Plate
2. Never place fingers or insert any ob-
ject into the unit while it is operating.
3. Always disconnect unit from its pow-
er source and wait for unit to cool
before handling, moving or servicing.
coupling and could
cause a gas leak.
attractant outlet faces downwind.
Illustration. 4
Female mosquitoes also feed on moisture laden nec-
tar and fruit juices when not in search of a blood
meal. They are usually found in shade; around flow-
ers, trees, bushes and other vegetation; and adjacent
to standing water.
Tank
Strap
WARNING
Screw & Nut
(2 places)
4. This device was designed for use
with propane gas. Never attempt to
use any other fuel, including liquid
fuels or natural gas. Fire or damage
to your Flowtron PowerTrap could
result.
Check for gas leaks by wetting the connec-
tions with a solution of soap and water and
watching for bubbles. If bubbles form or if a
bubble grows larger, there is a leak and
connection must be tightened.
Figure B
2. Insert one end of the
post into the post opening at the front of the tank
stand. Insert opposite end of post into the post
opening located at the bottom of the Flowtron
Mosquito PowerTrap®. Align unit in relation to the
tank stand. See Illustration 2.
For best results locate your unit 20 to 40 feet away
from areas of human activity in a location near (but
not in) bushes, wooded areas, or adjacent to standing
water (other than swimming pools). Select a location
which will result in the carbon dioxide plume blowing
toward the area where mosquitoes are likely to hide
and emerge. A proper location will ensure that
mosquitoes encounter the plume and follow it up-
wind to the Flowtron Mosquito PowerTrap before
they detect the presence of humans.
WARNING
Place a 20 lb. tank on the tank stand and install
tank wrap around the tank.
Check for gas leaks every time you disconnect and
reconnect a gas fitting.
5. Always operate the unit in an up-
right position to prevent damage to
Be sure there are no sparks or open flame in the
area when you check for leaks.
3. Install catch tray by first
inserting the rear of the
tray into the housing.
Then push in upper part
of the latch and raise
front of catch tray into
place. See Illustration 3.
2
the CO generator.
Tank
Cap
Do not use a liquid propane tank with a damaged
valve. Have dented or rusty propane tanks checked
by your propane supplier.
See Illustration 1.
6. Do not abuse the power pack.
Never carry the power pack by its
cord or yank it to disconnect it from
a receptacle. Keep power cord away
from heat, oil and sharp edges.
Only use regulator supplied with your Flowtron
PowerTrap.
Tank
Strap
Illustration 1
Prevailing wind direction
Post
Tank
Wrap
Plume
4. Position and screw pow-
er pack to either an out-
3. Place tank cap on top of tank.
Attractant
Outlet
side or inside wall adja-
cent to a electrical outlet
(screws not provided).
4 . Move your unit to the
desired location in your
yard. Remove catch tray
and grasp housing as
shown.
7. Never connect the unit to a
battery or other D.C. voltage. Such
an attempt will damage your unit.
HOUSE
PATIO 20 – 40 ft.
SOURCE OF
INSECTS
Tank
Stand
Cover
Install
screw
and
Run the low voltage wire
either above or below
ground from the power
pack to the unit. plug the
low voltage wire into the
power cord connector lo-
cated at the bottom of
the Flowtron Mosquito
PowerTrap®. Plug the
power pack into the elec-
trical outlet.
Tank
Stand
washer
Illustration 2
See trap “Placement” in-
structions on pg. 4.
8. Store indoors when not in use.
Remove propane tank from unit be-
fore storing and store tank outdoors
in a well ventilated space.
(MT-300 series only)
Push
See Illustration 5.
illustration 3
Page 4
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
When a timed mode is selected, the fan and LED
lights will come on immediately and remain on. The
unit, however, waits for dusk and then checks the out-
side air temperature to determine if it is sufficiently
warm for insect activity (above 55º – 60ºF). This is an
important feature to conserve propane fuel. The unit
will automatically begin its start cycle when the light
level reaches dusk and remains at the level of dusk
for ten minutes (thus avoiding the effects of transient
light sources) and if the outside air temperature is
above the 55º – 60ºF range.
Operation
Your Mosquito PowerTrap is fully automatic. It is
equipped with a photocell, temperature sensors and a
computer microprocessor.
Your Enemy – the Mosquito
There are some 2,700 species (different kinds of
mosquitoes) in the world with about 170 species in
North America alone.
How Your Flowtron
Mosquito PowerTrap Works
The revolutionary new Flowtron Mosquito PowerTrap
replicates the attractants mosquitoes use to locate, bite
and annoy humans. It does this by producing carbon
dioxide, heat and moisture and combining these stimuli
with octenol to create an attractant to mosquitoes.
The control panel is located on the top of the unit and
has the following operating modes:
Most mosquitoes live and die close to where they
hatch, although some can travel miles in search of a
host. Only the female mosquito bites as she requires
a blood meal to produce eggs.
•
•
•
24/7 (on 24 hours, 7
days/week)
Your Flowtron Mosquito PowerTrap:
•
Replicates the human attractants of respiration,
odor, body heat.
Mosquitoes require standing water in aquatic habitats
including fresh water, salt water marshes, brackish
water or in water found in containers, old tires, tree
holes, even flower pots. The female mosquito lays
her eggs on the surface of the water and if conditions
are right the eggs hatch and become larvae, then pu-
pae and finally adult mosquitoes; all in 10 to 14 days.
3 Hours (on at dusk,
off 3 hours later)
The start cycle is also repeated at dawn when the 3 +
2 hr or the 4 + 3 hr mode is selected.
•
Converts readily available propane gas into heat,
moisture and carbon dioxide, the acknowledged
leading mosquito and attractants emitted by hu-
mans.
3 + 2 Hours (on at dusk,
off 3 hours later; on again at dawn, off 2 hours lat-
er).
During start cycles, which are from five to ten
minutes in duration, the fan and LED lights operate
intermittently.
•
•
4 + 3 Hours (on at dusk, off 4 hours later;
on again at dawn, off 3 hours later)
•
•
Produces a powerful vacuum to draw mosquitoes
into a convenient, removable catch tray where
they quickly dehydrate and die for safe, clean dis-
posal.
Both male and female mosquitoes feed regularly on
nectar obtained from flowers, but females require
blood to produce fertile eggs. Therefore, she must
find a human or animal host to blood feed before she
can lay her eggs.
Off/Reset (manual off)
Ten to fifteen minutes after the unit detects a lack of
propane fuel (either due to an empty tank or due to
improper installation of the propane regulator to the
tank valve) the three green timed mode lights on the
control panel will flash. Simply switch the PowerTrap
off and refuel. If the unit is not out of propane and the
lights are flashing check that the tank valve is fully
open and that the regulator is properly attached to the
tank valve.
To select the desired mode, first push the button la-
beled “Off/Reset” to clear the computer memory.
Then push the button labeled “Mode”.
Contains state-of-the-art computer controlled elec-
tronics to operate automatically in one of four
modes selected by you.
Most mosquitoes that emerge in the wild never come
in contact with humans but obtain blood from birds
and other animals. Mosquito species that breed
around the home remain close to where they hatched
and are regarded as pests and carriers of disease.
For continuous operation press the “Mode” button
once. The green light labeled “24/7” will light and the
unit will operate continuously 24 hours per day until
the “Off/Reset” button is pressed.
Mosquito PowerTrap does away with ultraviolet lights
and high voltage killing grids. Most importantly, it kills
only female mosquitoe.
For timed operation, press and hold the “Mode” but-
ton. When the desired mode is selected as indicated
by its green light, release the button. No further con-
trol is necessary and your unit will function in the
mode selected every day until the “Off/Reset” button
is depressed or an interruption occurs in the electrical
power source.
Mosquitoes and biting flies are generally most active
shortly after dusk and again at dawn. Therefore, the 3
+ 2, or 4 + 3 timed modes are usually the most eco-
nomical settings.
Flowtron Mosquito PowerTrap uses an exclusive plat-
inum catalyst that converts air and propane gas into
heat, moisture and carbon dioxide. It does this in an
efficient, effective and economical manner. The cata-
lyst converter is completely safe, flameless and never
needs to be replaced.
Mosquitoes in search of a blood meal use visual,
thermal and olfactory (odor) stimuli to locate a host.
Of these, olfactory cues are the most important.
Out of the more than 100 compounds detected in hu-
man breath only two have been isolated and identi-
fied as significant mosquito and biting fly attractants;
carbon dioxide (CO2) and octenol (1-OCTEN-3-
OL). These attractants serve as long-range airborne
attractants and can be detected by mosquitoes and
biting flies at distances of 100 feet to 125 feet.
The 24/7 mode is desirable if day flying mosquitoes
are present or to operate at temperatures below 55º
F.
Note:
To resume operation following an electri-
cal disturbance or a loss of electrical
power, press the “Off/Reset” button to
clear the computer memory then reset
the unit to the desired operating mode.
At close range, body heat, moisture and lactic acid
serve as terminal attractants. Certain species show
strong preferences for biting different parts of the hu-
man body. This is thought to be related to local skin
temperature and lactic acid output.
In the event the PowerTrap fails to respond
to its controls (mode selection) unplug the
unit for a few seconds, reattach plug and
then reset to the desired mode.
Note:
As mosquitoes and biting flies pass through
the fan, most are killed and thrown against
the side of the internal screen-lined funnel.
Those that escape the fan’s killing action
end up in the catch tray where they quickly
dehydrate and die. See page 7 for instruc-
tions for removing the screen-lined funnel
and cleaning the screen.
The attractiveness of different persons to mosquitoes
varies substantially. Men are bitten more readily than
women, adults more often than children and larger
persons attract more mosquitoes perhaps because of
their greater relative heat and carbon dioxide output.
When the 24/7 mode is selected, the unit will begin
its start cycle and approximately three minutes later,
the fan and LED lights located in the entrance to the
trap will come on intermittently. Once the catalyst
has reached operating temperature, which will take
five to ten minutes, the fan and LED lights will remain
on and the start cycle will be complete.
Page 6
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
|