B2408
Instructions
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required.
Tool needed for assembly: Phillips Screwdriver (not included).
This product requires three “AA” batteries (included) for operation.
i
™
™
Crawl & Slide Arcade
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
WARNING
To prevent injury from falls:
• Use slide position for skilled walkers only.
• Keep product away from objects child
may fall on.
• Never leave child unattended.
Connectors
CAUTION
2
This product contains small parts
in its unassembled state.
• Plug the slide connector into the arcade connector. Push firmly to be
sure the connectors are completely joined.
Adult assembly is required.
Hint: Do not force the connectors together. If you cannot join them
easily, turn one of the connectors over and try again!
Slide
Retainer
Retainer
Slide
Arcade
1
3
• Place the arcade face up on a flat surface.
• Lift the slide slightly.
• With the smooth side of the slide facing down, fit the slide onto the
four pegs on the arcade.
• Fit the retainers onto the pegs of the arcade-slide assembly.
• Insert four .625" screws into the retainers and tighten.
• Set this assembly aside.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Base
Ramp
6
• Insert two .625" screws into the open ball drop and tighten.
4
• Turn the ramp and base upside-down with the ribbed side up.
• Fit the base onto the pegs on the ramp.
• Insert five .625" screws into the base and tighten.
Ball Drop
7
• Turn the other ball drop upside-down.
• Fit the ball drop to the corner of the base-ramp assembly, as shown.
Open Ball Drop
5
• Turn the open ball drop upside-down.
• Fit the open ball drop to the corner of the base-ramp assembly,
as shown.
Hint: You may want to prop up the end of the base-ramp assembly.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
8
10
• Insert two .625" screws into the ball drop and tighten.
• Insert two .625" screws into the support tube and tighten.
Support Tube
Support Tube
9
• Fit the ends of a support tube down through the hole in each
ball drop.
11
• Push the support tube down so that it is completely into the groove
in the base-ramp assembly.
• Fit the ends of the other support tube down through the hole in each
end of the base-ramp assembly, as shown.
• Push the support tube down so that it is completely into the groove
in the base-ramp assembly.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Bracket
12
• Insert two .625" screws into the support tube and tighten.
14
• Fit the bracket onto the base, so that the end of the support tube
inserts through it, as shown. Push the bracket down firmly to “snap”
it into place.
Arcade-Slide
Assembly
• Insert two .625" screws into the bracket and tighten.
Base-Ramp
Assembly
Ball Wheel
Knob
Groove
Groove
13
• Turn the base-ramp assembly upright.
15
• With the arcade-slide assembly facing down, fit the knobs into the
grooves in either end of the base-ramp assembly.
• Fit the ball wheel into the groove on the base, as shown.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Assembly
Large Arch Piece
Small Arch Piece
Ball Wheel
Bracket
18
“snap” into place.
• Insert a small arch piece into the large arch piece. Push firmly to
16
• Fit the ball wheel bracket onto the base, so that the end of the
support tube inserts through it, as shown. Push the ball wheel
bracket down firmly to “snap” it into place.
• Insert two .625" screws into the ball wheel bracket and tighten.
19
• Insert a .625" screw into the arch and tighten. Repeat steps 18 and
19 to assemble the other arch.
17
• Now, turn the assembly upside-down. Insert two .625" screws into
the base and tighten.
Download from Www.Somanuals.co7m. All Manuals Search And Download.
Assembly
“T” End
22
Note: Do not over-inflate the ball.
• Lift the plug on the ball. Inflate the ball and quickly close the plug.
• Insert the “T” end of the ball strap through the slot in either arch.
Pull the strap to be sure it is secure.
20
• Align the ends of the arches with the tops of the ball drops. Fit the
arches over the support tubes, as shown. Push the arches down
firmly to “snap” them into place.
Hint: The arches are designed to fit one way onto the tops of the
ball drops. If the arches do not fit onto the ball drops, try turning
them around!
21
• Insert a 1.25" screw through the ends of each arch and tighten.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Battery Replacement
Battery Safety Information
Batteries may leak fluids that can cause a chemical burn injury or ruin
your toy. To avoid battery leakage:
Hint: The batteries included are for in-store demonstration
purposes only. We recommend replacing the batteries that
came with this toy with three, new alkaline batteries.
Use alkaline batteries for longer battery life!
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the toy. Dispose of batteries safely. Do not
dispose of batteries in a fire. The batteries may explode or leak.
1.5V x 3
"AA" (LR6)
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
SHOWN ACTUAL SIZE
• Remove rechargeable batteries from the toy before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Power/Volume Switch
Battery Compartment Door
• Locate the battery compartment door on the front of the arcade.
• Loosen the screw in the battery compartment door. Remove the
battery compartment door.
• Insert three "AA" (LR6) alkaline batteries.
• Replace the battery compartment door and tighten the screw.
Power/Volume Switch
Hint: When sounds or lights from this toy become faint or stop,
it’s time for an adult to change the batteries!
• Slide the power/volume switch to off O; on with low volume
or on with high volume
• Slide the power/volume switch to the off position O when not in use.
;
.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Stage 1 – Crawl
Press for sounds,
music and lights.
Hanging inflatable ball for batting fun.
Push the teeter-totter for fun
sounds and lights too!
Fit balls in any ball drop
and watch them roll.
• Turn the unit on its side.
• Lift the arcade.
Hint: This will require a lot of force.
LIFT
• Push the slide under the base and “snap” it into place.
PUSH
Side View
Download from Www.Somanuals.co1m0. All Manuals Search And Download.
Stage 2 – Slide
Press the “step” for moving
lights, sounds and music.
Lift Slide
Pull Latch
Bottom View
• Turn the unit on its side.
• Pull the latch to release the slide.
• Push and “snap” the arcade into place.
PUSH
PULL
Side View
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumer Information
Questions? We’d like to hear from you!
Care
Call Fisher-Price® Consumer Relations, toll-free at 1-800-432-5437,
8 AM - 6 PM EST Monday through Friday. Hearing-impaired
consumers using TTY/TDD equipment, please call 1-800-382-7470.
Wipe this toy with a clean cloth dampened with a mild soap and
water solution. Do not immerse this toy. This toy has no consumer
replaceable parts. Do not take this toy apart.
Or, write to:
Fisher-Price® Consumer Relations
636 Girard Avenue
East Aurora, New York 14052, U.S.A.
FCC Statement (United States Only)
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
For countries outside the United States:
CANADA
Questions? 1-800-567-7724, Mattel Canada Inc., 6155 Freemont Blvd.,
Mississauga, Ontario L5R 3W2.
GREAT BRITAIN
Mattel UK Ltd, Vanwall Business Park, Maidenhead SL6 4UB. Helpline: 01628 500302.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference
to radio o television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
AUSTRALIA
Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond,
Victoria 3121 Australia. Consumer Advisory Service 1300 135 312.
NEW ZEALAND
16-18 William Pickering Drive, Albany 1331, Auckland.
• Reorient or relocate the receiving antenna.
ASIA
Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City,
Tsimshatsui, HK, China.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Note: Changes or modifications not expressly approved by the
manufacturer responsible for compliance could void the user's
authority to operate the equipment.
Fisher-Price, Inc., a subsidiary of Mattel, Inc. East Aurora, New York 14052, U.S.A.
©2003 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
Printed in Mexico
B2408pr-0920
Download from Www.Somanuals.com. All Manuals Search And Download.
|