Fisher Price Crib J6982 User Manual

J6982  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Battery Installation  
Assembly  
IMPORTANT! Before assembly and each use, inspect this product  
for damaged hardware, loose joints, missing parts or sharp edges.  
DO NOT use if any parts are missing or broken. Contact Mattel for  
replacement parts and instructions if needed. Never substitute parts.  
Hint: We recommend using alkaline batteries for  
longer battery life.  
1,5V x 4  
“D” (LR20)  
Base Tubes  
Lift  
Lift  
Base  
1
• Lift both base tubes.  
Hubs  
• Loosen the screws in the battery compartment door and remove  
the battery compartment door.  
• Insert fourD(LR20) alkaline batteries into the battery compartment.  
• Replace the battery compartment door and tighten the screws.  
• Low battery power may cause this product to operate erratically  
(no movement/no sounds) and the product may not turn off. If this  
should happen, remove and discard all batteries and replace with  
four, new “D” (LR20) alkaline batteries.  
Base Tubes  
Protect the environment by not disposing of this product with  
household waste (2002/96/EC). Check your local authority for  
recycling advice and facilities (Europe only).  
Base Tubes  
Battery Safety Information  
In exceptional circumstances, batteries may leak fluids that  
can cause a chemical burn injury or ruin your product.  
To avoid battery leakage:  
• Do not mix old and new batteries or batteries of different types:  
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).  
2
• Position the hubs with the smooth side out.  
• Fit the hubs onto the base tubes.  
• Insert batteries as indicated inside the battery compartment.  
• Remove batteries during long periods of non-use.Always remove  
exhausted batteries from the product. Dispose of batteries safely.  
Do not dispose of this product in a fire.The batteries inside may  
explode or leak.  
Hint: The hubs are designed to fit the base tubes one way. If the  
hubs do not fit on the base tubes, check to be sure the smooth side  
is out.  
• Never short-circuit the battery terminals.  
• Push the hubs down until you hear a “click”.  
• Use only batteries of the same or equivalent type as recommended.  
• Do not charge non-rechargeable batteries.  
• Pull up on the hubs to be sure each is secure.  
• Remove rechargeable batteries from the product before charging.  
• If removeable, rechargeable batteries are used, they are only to be  
charged under adult supervision.  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Seatback Tube  
Wide Slot  
Narrow Slot  
Footrest Tube  
5
3
• Position the pad onto the frame assembly.The extra, padded portion  
should be toward the seat back tube.  
• Position the footrest tube so that it curves down.  
• Fit the ends of the footrest tube into the wide slots in the hubs.  
• Position the seat back tube so that it curves down.  
• Fit the ends of the seat back tube into the narrow slots in the hubs.  
Seat Back Tube  
Hubs  
6
• Fit the upper pocket on the pad around the seat back tube.  
4
• Insert a #8 x 3,2 cm screw into each hub and tighten.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Assembly  
Headrest Pad  
Footrest Tube  
Restraint  
Belts  
7
• Fit the lower pocket on the pad around the footrest tube. Fasten the  
straps underneath the footrest tube to secure the lower portion of  
the pad.  
9
• Fit the restraint belts through the slots in the headrest pad.  
• Fit the headrest pad to the liner/pad.  
PUSH  
PUSH  
Toy Bar  
Sockets  
8
• Push down on the pad to be sure it is assembled properly. If the  
pad falls through the frame, you have not assembled it properly.  
Please re-read these instructions and re-assemble the pad.  
10  
• Fit the toy bar plugs into the frame sockets..  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Set-up  
WARNING  
To prevent serious injury or death from falls  
and being strangled in the restraint system:  
Fall Hazard - It is dangerous to use this  
product on an elevated surface, since  
child’s movement may cause the product  
to slide or tip over. Use only on a floor.  
Suffocation Hazard - Never use on a soft  
surface (bed, sofa, cushion) since the  
product can tip over and cause suffoca-  
tion in soft surfaces.  
• Always use the restraint system.  
Back View  
• Not recommended for children who  
can sit up by themselves (6 months  
approximately, until 9 kg/20 lbs).  
Seat Position  
• Adjust the seat position for baby’s comfort.  
• Lift the fabric skirt near the seat back of the frame.  
Upright: Fasten the liner/pad buckles. Make sure you hear a “click”.  
Recline: Unfasten the liner/pad buckles.  
• Never leave child unattended.  
• Never use the toy bar as a handle.  
Side-to-Side  
Head-to-Toe  
Swinging Direction  
• Adjust the seat to change gliding motion to: Side-to-Side or  
Head-to-Toe.  
• Turn the seat for baby’s comfort.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Securing Baby  
Starting Gliding Motion  
Restraint Belts  
Restraint Pad  
• Place your child in the product. Position the restraint pad between  
your child’s legs.  
• Fasten both restraint belts to the buckles on each side of the  
restraint pad. Make sure you hear a “click” on both sides.  
• Check to be sure the restraint system is securely attached by  
pulling it away from your child.The restraint system should  
remain attached.  
Power/Speed Switch  
Anchored End  
Anchored End  
Free End  
Free End  
• Make sure your child is properly secured in the seat.  
TIGHTEN  
LOOSEN  
• Slide the power/speed switch to slow  
or fast  
.
Hint:. In most cases, the slow setting works best for a smaller child,  
while the fast setting works best for a larger child. If gliding stops  
while using the slow setting, try the fast setting. Give the seat a light  
push to start the gliding motion again.  
To tighten the belts: Feed the anchored end of the restraint up  
through the buckle to form a loop . Pull the free end of the  
restraint .  
To loosen the belts: Feed the free end of the restraint up through  
the buckle to form a loop . Enlarge the loop by pulling on the end  
of the loop toward the buckle. Pull the anchored end of the restraint  
to shorten the free end of the belt .  
• Be sure to turn this product off when not in use. Slide the power/  
speed switch to the off setting  
.
• For best performance, make sure this product is used on a  
completely level surface.  
Please Note: After adjusting the restraint system to fit your child, make  
sure you pull on it to be sure it is securely fastened.  
Note: If gliding motion is slow in one direction (and you hear a winding  
or grinding noise), you may be using this product on an inclined surface.  
Use this product only on a completely level surface.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
Room-to-Room Portability  
Music  
Music Switch  
• Choose the style of music for baby. Slide the music switch to:  
Soothing  
Playful  
Off  
• Slide the volume switch to  
for low volume;  
for high volume.  
Note: Low battery power may cause this product to operate erratically  
(no movement/no sounds) and the product may not turn off. If this  
should happen, remove and discard all batteries and replace with four,  
new “D” (LR20) alkaline batteries.  
• Make sure your child is properly secured in the glider.  
• Grasp both handles, as shown, and lift.  
• Carefully carry the glider to another room. Be sure to set the glider  
down only on the floor.  
Care  
• The liner/pad and headrest pad are machine washable.Wash them  
separately in cold water on the gentle cycle. Do not use bleach.  
Tumble dry separately on low heat and remove promptly.  
• The frame and toy bar may be wiped clean using a mild cleaning  
solution and a damp cloth. Do not immerse the frame.  
To remove the liner and headrest pad:  
• Feed the restraint belts back through the slots in headrest pad.  
Pull to remove the headrest pad.  
• Lift the fabric skirt near the footrest of the frame.  
• Unfasten the liner/pad buckles. Pull to remove the liner/pad bottom  
pocket from the footrest tube; pull to remove the liner/pad upper  
pocket from the seatback tube.  
• To replace the pad: refer to Assembly step 5 - 9.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  

CTX Oven G 26 User Manual
Curtis DVD Player DVD6041 User Manual
CyberData Network Card Ethernet IV Printer Module User Manual
Dimplex Thermostat TS521W User Manual
Electro Voice Portable Speaker ECS 15 3 User Manual
Electro Voice Portable Speaker S 1202ER User Manual
Extron electronic Network Card RGB 160 User Manual
Gefen Flat Panel Television 4x4 HDTV Matrix User Manual
GE Monogram Refrigerator Drawer Freezer Refrigerator User Manual
GE Oven 169089 User Manual