Specifications
Video input — RGB 580xi AAP / CCS AAP / CCSI AAP
Number/signaltype .......................... 1 analog RGBHV, RGBS, RGsB, RsGsBs
Connectors ........................................... 1 15-pin HD female
User’s Guide
Video output — RGB 580xi AAP / CCS AAP / CCSI AAP
Number/signaltype .......................... 1 analog RGBHV, RGBS, RGsB
Connectors ........................................... 1 15-pin HD female
General
Temperature/humidity ..................... Storage -40° to +158°F (-40° to +70°C) / 10%
to90%,non-condensing
Operating +32° to +122°F (0° to +50°C) / 10%
to90%,non-condensing
Enclosuredimensions
RGB 580xi AAP/Cable Cubby AAP models (double-height plates)
Faceplate ................................ 1.4" H x 3.5" W (3.6 cm H x 8.9 cm W)
Circuit board ......................... 1.3" H x 2.5" W x 0.9" D
(3.3 cm H x 6.4 cm W x 2.3 cm D) Depth
excludes connectors and knobs.
Shippingweight .................................. AAP models . 1 lb (0.5 kg)
Vibration .............................................. ISTA/NSTA 1A in carton (International Safe
Transit Association)
Approvals............................................ UL, CUL, CE, FCC Class A
MTBF .................................................... 30,000 hours
Warranty .............................................. 3 years parts and labor
Specifications are subject to change without notice.
RGB 580xi AAP/CC AAP Series
RGB 580xi AAP, RGB 580xi S/CCS AAP,
RGB 580xi SI/CCSI AAP
Extron Electronics, USA
1230 South Lewis Street
Anaheim, CA 92805
USA
714.491.1500
Fax 714.491.1517
Extron Electronics, Europe
Beeldschermweg 6C
3821 AH Amersfoort
The Netherlands
+31.33.453.4040
Fax +31.33.453.4050
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Building
Singapore 368363
+65.6383.4400
Fax +65.6383.4664
Extron Electronics, Japan
Kyodo Building
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082 Japan
+81.3.3511.7655
Fax +81.3.3511.7656
68-537-01 Rev. C
03 06
© 2006 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Installation and Operation
Extron’s RGB 580xi AAP double-space devices are designed to
complement the RGB 580xi remote interface. They may be
mounted to any Extron product which has an AAP faceplate or to
an AAP wallplate. See the “AAP Device Part Numbers” and the
“Cable Cubby AAP Device Part Numbers” sections for AAP/CC
AAP part numbers.
Tip (L)
Sleeve (GND)
Ring (R)
Tip (L)
Sleeve (GND)
RGB 580xi AAP/CC AAP Series Features
Audioinputwiring
3
4
3
Horizontal shift control knob — While viewing the
displayed image, rotate this control to move the image to
the right or left on the screen. The power/signal LED will
flash green whenever the minimum and maximum limits
of this control are reached.
4
5
RGB 580xi AAP
RGB 580xi S AAP
SHIFT
AUDIO IN
COMPUTER IN
AUDIO IN
COMPUTER IN
RGB 580xi
RGB 580xi
1
2
1
2
3
4
Input select button — Pressing this button will result in
contact closure between pins A and B of the contact closure
control connector on the front panel of the RGB 580xi
remote interface. This button can also be used for direct
control of any Extron contact closure-controlled switcher,
or as a direct connection to an external control system.
RGB 580xi SI AAP
SELECT
SHIFT
AUDIO IN
COMPUTER IN
RGB 580xi
1
5
2
Mounting the RGB 580xi AAP Device
4
4
RGB 580xi CCSI AAP
RGB 580xi CCS AAP
The AAP device should be cabled before attaching the AAP
device to a faceplate or wallplate. The screws needed for
installing an AAP device are built into its front panel, so no
additional screws will be needed.
Installation and service must be performed by
authorized personnel only.
CAUTION
1
1
5
1.
2.
Connect the output cables to the AAP device’s rear
connectors. See the section “Cabling the AAP/Cable Cubby
AAP Device Rear Connectors” in this user’s guide.
Power/signal LED — This LED lights
1
•
amber to indicate that the AAP device is receiving
power.
Insert the AAP device’s screws through the holes in the AAP
double-space faceplate, the AAP wallplate, or the Cable
Cubby AAP shelf bracket. Secure the AAP device to the
faceplate/wallplate/shelf bracket with the provided captive
washers and #4-40 nuts.
•
green to indicate that an active sync signal is present at
the input and the AAP device is receiving power.
The LED will flash green whenever the minimum and
maximum limits of the horizontal shift control (H. shift)
have been reached.
Computer video input connector — Attach a cable from
the computer source to this 15-pin HD female connector.
2
3
Audio input connector — Plug a 3.5 mm stereo plug into
this jack for unbalanced audio input. Wire the male plug as
shown in the following illustration.
RGB 580xi AAP • Installation and Operation
2
RGB 580xi AAP • Installation and Operation
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and Operation
Installation and Operation
To cable the captive screw connectors, please refer to the
following diagrams and orient the wires according to the view
angle of the captive screws. When using Extron’s VGA and
control cable assembly (see the “Cables” section for part
numbers), refer to the color of each wire for signal identification.
Cable
Clamp
Control connector (J4) — Insert wires into and tighten the
screws on this 3.5 mm, 5-pole captive screw connector.
This connector is used for contact closure and horizontal
shift signals. Wire the connector as shown below.
1
AAP 102
Cable
2
0
1
P
A
A
IO
D
U
A
R
TE
Horizontal shift
Horizontal shift ground (gray)
Horizontal shift (brown)
Contact closure (light blue)
Contact closure (purple)
+
(green)
PU
M
CO
P
A
T
C
E
A
P
L
I
IN
T
S
i
x
0
8
E
S
B
G
R
S
H
–
RGB 580xi SI AAP
+
–
#4-40 Nut w/ Captive
Washer
LED connector (J2) — Insert wires into and tighten the
screws on this 3.5 mm, 3-pole captive screw connector.
This connector is used for powering the green/amber LED.
Wire the connector as shown below.
2
3
Example of mounting an AAP device to a wallplate
Cabling the AAP/Cable Cubby AAP Device
Rear Connectors
Green LED (pink)
LED ground (yellow)
Amber LED (orange)
Extron’s various AAP/Cable Cubby AAP devices for the
RGB 580xi may come with several rear connectors that may
require cabling.
Audio output connector (J3) — Insert wires into and
tighten the screws on this 3.5 mm, 3-pole captive screw
connector. This connector is used for unbalanced stereo
audio output. Wire the connector as shown below.
Although the control cable, LED, and audio assemblies
will come prewired (AAP only) to the captive screw
connectors, any subsequent cable assembly replacement
will require the following cabling instructions.
Audio right (red)
Audio ground (black)
Audio left (white)
3
J3
On Cable Cubby AAP models, the VGA and audio cable
assemblies will be routed through the Cable Cubby. Refer
to the Cable Cubby User’s Manual (part #68-701-01) for
Cable Cubby installation instructions.
J4
J2
Red
Black
White
Lt. Blue
Purple
RGB 580xi CCSI AAP
1
Green
Gray
Brown
2
Yellow
Pink
Orange
Example of AAP device rear connectors
CC AAP VGA connector
CC AAP Audio connector
J4
1
J2
2
Cable Cubby
Example of Cable Cubby AAP device rear connectors
4
RGB 580xi AAP • Installation and Operation
RGB 580xi AAP • Installation and Operation
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Part Numbers
Part Numbers
AAP Devices
Optional RGB 580xi AAP Extension Cables
These cables only apply to the RGB 580xi AAP,
RGB 580xi S AAP, and RGB 580xi SI AAP, they do
not apply to the RGB 580xi CCS AAP or RGB 580xi
CCSI AAP.
Description
Part number
RGB 580xi AAP 3' (black, white,
RAL9010 white)
70-128-02, -03, -05
70-129-02, -03, -05
70-134-02, -03, -05
70-135-02, -03, -05
70-137-02, -03, -05
70-138-02, -03, -05
RGB 580xi AAP 6' (black, white,
RAL9010 white)
VGA and control cable assembly
Part number
VGA and control cable 3' (0.9 m)
VGA and control cable 6' (1.8 m)
VGA and control cable 12' (3.6 m)
VGA and control cable 25' (7.6 m)
VGA and control cable 35' (10.6 m)
VGA and control cable 50' (15.2 m)
26-521-01
26-521-02
26-521-03
26-521-04
26-521-05
26-521-06
RGB 580xi S AAP 3' (black, white,
RAL9010 white)
RGB 580xi S AAP 6' (black, white,
RAL9010 white)
RGB 580xi SI AAP 3' (black, white,
RAL9010 white)
RGB 580xi SI AAP 6' (black, white,
RAL9010 white)
Cable Cubby AAP Devices
Description
Part number
RGB 580xi CCS AAP 9' (black)
RGB 580xi CCS AAP 12' (black)
RGB 580xi CCSI AAP 9' (black)
RGB 580xi CCSI AAP 12' (black)
70-254-02
70-255-02
70-256-02
70-257-02
RGB 580xi AAP • Installation and Operation
6
RGB 580xi AAP • Installation and Operation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|