User’s Guide
PVT CV, PVT RGB CV,
PVT RGB and PVT SW RGB
PoleVault™ Twisted Pair Transmitters
(Rack Mount Models)
68-1310-01
Rev. C
04 07
Download from Www.Somanuals.com. All Manuals Search And Download.
Precautions
䄺ਞ
ᅝܼ乏ⶹꢀꢀ噝ꢀꢀЁ᭛
⬉⑤ꢀ噝ꢀ䆹䆒া㛑Փ⫼ѻકϞᷛᯢⱘ⬉⑤DŽꢀ䆒ᖙ⫼᳝
ഄ㒓կ⬉㋏㒳կ⬉DŽϝᴵ㒓˄ഄ㒓˅ᰃᅝ䆒ᮑˈϡ㛑ϡ
⫼䏇䖛DŽ
ꢀꢀꢀꢀꢀꢀꢀꢀⱘ᪡㓈ᡸ䇈ᯢDŽ
ᢨᥝ⬉⑤ꢀ噝ꢀЎᅝܼഄҢ䆒ᢨᥝ⬉⑤ˈ䇋ᢨᥝ᠔᳝
ꢀꢀ⬉⑤㒓DŽ
ꢀ
ꢀꢀꢀꢀꢀꢀꢀꢀ䴆ⱘॅ䰽⬉य़ˈ᳝㾺⬉ॅ䰽DŽ
⬉⑤㒓ֱᡸꢀ噝ꢀཹᏗ㒓ˈꢀ䙓ܡ 㹿䏽䏣ˈ䞡⠽य़DŽ
㓈ᡸꢀ噝ꢀ᠔᳝㓈ׂᖙ乏⬅䅸䆕ⱘ㓈ׂҎਬ䖯㸠DŽꢀ䆒
ꢀꢀϡ㽕㞾Ꮕ䆩ᠧᓔ䆒Ⲫᄤ㓈ׂ䆹䆒DŽ
䗮亢ᄨꢀ噝ꢀ᳝ѯ䆒ᴎϞ᳝䗮亢ῑᄨˈᅗӀᰃ⫼
ꢀꢀ䰆ℶᴎݙ ᬣᛳܗ ӊ䖛⛁DŽϡ㽕⫼ӏԩϰ㽓ᣵԣ䗮亢ᄨDŽ
䫖⬉∴ꢀ噝ꢀϡℷ⹂ⱘᤶ⬉∴Ӯ᳝⟚⚌ⱘॅ䰽DŽᖙ乏Փ
ꢀꢀϢॖᆊ㤤ⱘⳌৠⳌ䖥ൟোⱘ⬉∴DŽᣝ✻⫳ѻॖⱘ
⊼ᛣ
䯙䇏䇈ᯢкꢀ噝ꢀ⫼᠋Փ⫼䆹䆒ࠡᖙ乏䯙䇏ᑊ⧚㾷
ꢀꢀ᳝ᅝܼՓ⫼䇈ᯢDŽ
ֱᄬ䇈ᯢкꢀ噝ꢀ⫼᠋ᑨֱᄬᅝܼ䇈ᯢкҹᇚᴹՓ⫼DŽ
ꢀꢀ䙉ᅜ䄺ਞꢀ噝ꢀ⫼᠋ᑨ䙉ᅜѻક⫼᠋ᣛफϞⱘ᠔᳝
ꢀꢀᅝܼ᪡䇈ᯢDŽ
ꢀꢀ䆂໘⧚ᑳᓗ⬉∴DŽ
Download from Www.Somanuals.com. All Manuals Search And Download.
This page was deliberately left blank.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter One • Introduction..................................................... 1-1
Tabletop use............................................................................ 2-3
Rack mounting........................................................................ 2-3
transmission...................................................................... 2-9
Appendix A • Reference Material ......................................A-1
All trademarks mentioned in this manual are the properties of their respective owners.
68-1310-01
Rev. C
04 07
PVT Series (Rack Mount Models) • Table of Contents
i
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents, cont'd
This page was deliberately left blank.
ii
PVT Series (Rack Mount Models) • Table of Contents
Download from Www.Somanuals.com. All Manuals Search And Download.
PVT Series (Rack Mount Models)
Chapter One
1
Introduction
About.the.PVT.Transmitters
Application.Diagram
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
About the PVT Transmitters
The Extron P�T Series (Pole�ault™ Twisted Pair Transmitters)
are a series of cost effective twisted pair transmitters that work
exclusively with the PVS 204SA, a four-input twisted pair
switcher with a built in power amplifier.
PVT transmitters can transmit composite video and stereo audio
or high resolution video (RGB) and stereo audio to the
PVS 204SA switcher over CAT 5 twisted pair cable, up to a
distance of 100 feet. All transmitters are remotely powered
via the twisted pair cable when connected to the PVS 204SA
switcher.
This manual covers the rack mount models only.
For Decora® and AAP models, refer to the manual (part
number 68-1259-01) for those devices.
N
PVT series of transmitters are compatible ONLY
with the PVS 204SA switcher.
N
N
For PVS 204SA installation and operation information,
refer to the manual supplied with the device.
The PVT transmitter rack mount models can be mounted on 1U
19" or standard rack shelves, or mounted under or on desks.
The PVT series rack mount models are as follows:
PVT CV — Transmits composite video and stereo audio.
PVT RGB, PVT SW RGB — Transmits computer (RGB) video
and stereo audio.
PVT RGB CV — Transmits composite video, computer video
and two stereo audio signals.
See the "About the PVT xx" sections in this chapter for details.
The PVT transmitters are part of a system for distribution of
composite or computer video and audio, over Extron Enhanced
Skew-Free™ A/V UTP Cable, or any CAT 5, 5e, or 6 shielded
twisted pair (STP), unshielded twisted pair (UTP), or foil
shielded twisted pair (FTP) cable.
Transmission distance
The maximum distance is determined by the frequency and
resolution of the signal that is input to the transmitter. However,
all PVT models can transmit signals to the PVS 204SA switcher
if it is located not more than 100 feet away. The optimum
distance is between 50 and 75 feet.
1-2
PVT Series (Rack Mount Models) • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
About the PVT CV
The P�T C� Twisted Pair Transmitter is a 1/8 rack mounting
model that can transmit composite video and stereo audio to the
PVS 204SA switcher. This model can also be mounted under a
desk or shelf, or on certain projector poles.
AUDIO
IN
L
VIDEO
IN
R
VIDEO OUT
PVT CV
Figure 1-1 — PVT CV face and rear panel
About the PVT RGB
The P�T RGB Twisted Pair Transmitter is a 1/4 rack mounting
model that can transmit high resolution (RGB) video and an
associated stereo audio signal to the PVS 204SA switcher. It has
a local monitor output for image monitoring. This model can
also be mounted under a desk or shelf, or on certain projector
poles.
PVT RGB
PVT RGB
RGB A OUT
MONITOR OUT
INPUT
RGB B OUT
Figure 1-2 — PVT RGB face and rear panel
PVT Series (Rack Mount Models) • Introduction
1-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont’d
About the PVT RGB CV
The P�T RGB C� Twisted Pair Transmitter is a 1/4 rack
mounting model that can transmit high resolution (RGB) video
and composite video, and two associated stereo audio signals to
the PVS 204SA switcher. This model can also be mounted under
a desk or shelf, or on certain projector poles.
RGB
VIDEO
PVT RGB CV
RGB A OUT
AUDIO
IN
AUDIO IN
L
VIDEO
IN
COMPUTER IN
R
VIDEO OUT
RGB B OUT
Figure 1-3 — PVT RGB CV face and rear panel
About the PVT SW RGB
The P�T SW RGB Twisted Pair Transmitter is a 1/4 rack
mounting model with two input connectors, a local monitor
output, and a remote contact closure connector. It transmits
high resolution (RGB) video and stereo audio signals to the
PVS 204SA, and switches between the two inputs by front
panel, remote, or auto switching. In addition, the local monitor
output can be set to accept only the input 1 signal, or to follow
the current active input signal. This model can also be mounted
under a desk or shelf, or on certain projector poles.
AUTO
SWITCH
ON
FOLLOW
MONITOR
AUTO
1
2
MANUAL
INPUT
1
PVT SW RGB
REMOTE
INPUT 1
RGB A OUT
PIN1 - IN 1
PIN4 - IN 2
PIN5 - GND
CONTACT
RGB B OUT
INPUT 2
MONITOR OUT
Figure 1-4 — PVT SW RGB face and rear panel
PVT Series (Rack Mount Models) • Introduction
1-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Application Diagram
Extron
SI 26X
Two-way, Open Back
Ceiling Speakers – 1 Pair
Option
Extron
SI 26X
Two-way, Open Back
Ceiling Speakers – 1 Pair
Extron
SPK 18 - 25'
Cable
Included
Extron
PCM 240
Projector Drop
Ceiling Mount
Extron
PMP
Projector
Mount Pole
Extron
PVS 204SA
TS
ms
PU
4/8
Oh
IE
D
O
UT
PLIF
AM
™
R
UND
T
SH UTP
OL
O
R
T
G
R
O
RO
UTS!
L
DC
V
DO
N
O
R
O
/IR
L
C
1
2
V
E
D
17T
I
D
E
T
O
SPE
AKE
-
2
32
R
M
L
I
S
T
I
/
V
U
S
R
S
x
I
PoleVault
Switcher
A
U
D
RA
T
R
1
0V UTE
L/M
U
S
AP
P
A
Tx
O
®
C
B
A
B
X
IN
X/MI
RG
O
U
T
P
U
T
A
U
EO
A
VID
3
S
2A
B
RG
1A
IDEO
V
3B
I
N
P
U
T
2B
R
S
WE
1B
PO
12VMAX
3A
Extron
PMK 350
Multi-product Projector
Mounting Kit
Hardwired IR Cable
to Switcher Included
Extron
UPB 25
Universal Projector
Mounting Bracket
Y
A
L
P
S
I
D
O
F
F
O
N
C
P
O
E
L
O
ID
V
V
L
O
V
RS-232 Cable
to Projector
Included
2
5
C
L
M
UTP Cable
Included
Extron
MLC 52 RS
Basic MediaLink
Controller
Extron
PVT RGB CV
VGA, Composite Video
W/Audio UTP Transmitter
Line Level
Audio
A
C
T
IV
E
M
U
T
E
M
IC
IN
A
U
IN
D
IO
V
ID
IN
E
O
L
A
U
D
IO
IN
R
R
G
COM
PU
B
A
O
V
U
T
ID
TE
Extron
E
R
O
IN
O
U
T
R
MLP 101 D
G
B
B
O
U
T
Mic to Line Preamplifier
Option
Extron
PVT CV
Composite Video
w/ Audio UTP
Transmitter
Option
DVD/VCR Combo
Laptop
w/ Audio
A
U
IN
DI
O
VI
D
IN
EO
L
R
VI
D
EO OU
T
Aux. Video Source
Figure 1-5 — Typical PVT series system application
using PVT RGB CV and PVT CV transmitters with the
PVS 204SA and other Extron devices
1-5
PVT Series (Rack Mount Models) • Introduction
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction, cont'd
This page was deliberately left blank.
PVT Series (Rack Mount Models) • Introduction
1-6
Download from Www.Somanuals.com. All Manuals Search And Download.
PVT Series (Rack Mount Models)
Chapter Two
2
Installation
UL/Safety.Requirements
Installing.the.PVT.Twisted.Pair.Transmitters
Connections.and.Settings
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
UL/Safety Requirements
The Underwriters Laboratories (UL) requirements listed below
pertain to the safe installation and operation of the transmitters.
Important safety instructions
1.
2.
3.
4.
5.
6.
7.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8.
9.
Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
Do not defeat the safety purpose of the polarized or
grounding type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
PVT Series (Rack Mount Models) • Installation
2-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the PVT Twisted Pair Transmitters
The PVT CV is a 1/8 rack shelf mountable transmitter, and
the PVT RGB, PVT RGB CV, and PVT SW RGB are 1/4 rack
shelf mountable transmitters. Each of the four models can
be mounted under a desk or shelf, or on to certain projector
mounts, and are also suitable for tabletop use.
Tabletop use
The PVT comes with self-adhesive rubber feet attached to the
four corners of the bottom. Set the PVT on a horizontal surface.
UL requirements for rack mounted devices
The following Underwriters Laboratories (UL) requirements
pertain to the safe installation of the PVT transmitter in a rack.
1.
Elevated operating ambient temperature — If installed in
a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than
room ambient temperature. Therefore, install the device
in an environment compatible with the maximum ambient
temperature (Tma = +122 °F, +50 °C) specified by Extron.
2.
3.
4.
Reduced air flow — Install the equipment in a rack so that
the amount of air flow required for safe operation of the
equipment is not compromised.
Mechanical loading — Mount the equipment in the rack
so that a hazardous condition is not achieved due to
uneven mechanical loading.
Circuit overloading — Connect the equipment to
the supply circuit and consider the effect that circuit
overloading might have on overcurrent protection and
supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this
concern.
5.
Reliable earthing (grounding) — Maintain reliable
grounding of rack-mounted equipment. Pay particular
attention to supply connections other than direct
connections to the branch circuit (e.g., use of power strips).
Rack mounting
For rack mounting, mount the PVT on a VersaTools® 19" 1U
rack shelf (RSF 123, part #60-190-20 or RSB 123, #60-604-20)
(figure 2-1) or on a standard 1U rack shelf (RSU 129, part #60-
190-01 or RSB 129, #60-604-01) (figure 2-2). On standard rack
shelves, the PVT CV can be mounted in one of eight locations to
the rear or the front of the rack, and the PVT RGB and RGB CV
in one of four locations to the rear or front of the rack.
PVT Series (Rack Mount Models) • Installation
2-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
To rack mount a PVT transmitter, do the following:
1.
2.
If installed, remove the feet from the bottom of the PVT.
Mount the PVT using two 4-40 x 3/16" screws in opposite
(diagonal) corners to secure the PVT to the shelf.
3.
Install blank panel(s) or other unit(s) to the rack shelf.
VersaTools
Rack Shelf
Eighth Rack
Width Device
Quarter Rack
Width Device
Quarter and Eighth
Rack Width False
Front Face Plate
(2) 4-40 x 3/16"
Screws
Figure 2-1 — Mounting the PVT on a VersaTools rack
shelf
Quarter Rack
Width Device
Eighth Rack
Width Device
M
D
D
A
IS
T
S
N
R
IB
E
A
U
R
IE
T
IO
S
M
P
L
IF
IE
R
Figure 2-2 — Mounting the PVT on a standard rack
shelf
PVT Series (Rack Mount Models) • Installation
2-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Furniture mounting
Use the optional mounting kit (MBU 123, under desk mounting
kit, part #70-212-01) to mount the PVT as follows:
1.
2.
If installed, remove the feet from the bottom of the PVT.
Attach the mounting brackets to the PVT with the machine
screws provided (figure 2-3).
Figure 2-3 — Mounting the PVT under a desk
3.
Hold the PVT with the attached brackets against the
underside of the mounting surface. Mark the bracket
screw hole locations on the mounting surface.
4.
5.
6.
Drill four 3/32" (2 mm) diameter pilot holes, 1/4" (6.3 mm)
deep in the mounting surface at the marked locations.
Insert #8 wood screws into the pilot holes. Tighten the
screws until just less than 1/4" of the head protrudes.
Align the mounting screws with the slots in the brackets
and place the PVT against the surface, with the screws
through the bracket slots.
7.
Slide the PVT slightly forward or back, then tighten all
four screws to secure the PVT in place.
2-5
PVT Series (Rack Mount Models) • Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Connections and Settings
N
Do not connect these devices to a computer data
or telecommunications network. Do not connect
these devices to an MTP system.
Front panel features
The front panel features are the same for the PVT CV, PVT RGB,
and PVT RGB CV. The PVT SW RGB features are unique to that
model.
1
PVT CV
PVT CV
1
PVT RGB
PVT RGB
1
RGB
VIDEO
PVT RGB CV
PVT RGB CV
2
3
4
FOLLOW
MONITOR
AUTO
AUTO
SWITCH
ON
1
2
MANUAL
INPUT
1
PVT SW RGB
PVT SW RGB
Figure 2-4 — PVT series front panel features
2-6
PVT Series (Rack Mount Models) • Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Dual color power LED — This LED lights amber when
power only (no signal) is applied to the PVT, and green
when power and a signal are both present.
a
AUTO
SWITCH
Auto switch LED (P�T SW RGB only) — This LED
lights green when the unit is in auto switch mode.
b
c
Input selection button with LED (P�T SW RGB only) —
Press these buttons to select (switch) between inputs
1 and 2. The associated LEDs lights green when
the input has an active video signal connected, and
amber when there is no signal present.
1
Dual configuration dual DIP switch (P�T SW RGB only) —
d
The left DIP switch allows the user to
FOLLOW
MONITOR
INPUT 1
AUTO
ON
select the switching mode, and the right
DIP switch allows the user to configure
the local monitor output from the rear
panel.
MANUAL
Switching mode (left DIP switch):
Set the switch up to Auto for automatic switching of the inputs
with an active signal.
When turning off auto switching, the PVT goes back to
the input that was selected prior to turning the auto-
switching on.
N
Set the switch down to Manual for front panel input switching
or input switching by contact closure control.
In Auto mode, if both inputs have an active signal,
Input 1 has priority.
N
Local monitor output (right DIP switch):
Set the switch up to Follow for automatic switching of the local
monitor output to the current selected input.
Set the switch down to Input 1 for local monitor output of the
signal from input 1 only.
2-7
PVT Series (Rack Mount Models) • Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Rear panel features
For all PVT rack mount models, the input connectors and the
output connectors are on the rear panel (see figure 2-5).
1
2
AUDIO
IN
L
VIDEO
IN
R
VIDEO OUT
PVT CV
3
4
1
2
RGB A OUT
AUDIO
IN
AUDIO IN
6a
6ba
L
VIDEO
IN
COMPUTER IN
R
VIDEO OUT
RGB B OUT
PVT RGB CV
3
5
PVT RGB
RGB A OUT
6a
6ba
MONITOR OUT
INPUT
RGB B OUT
PVT RGB
4
4
5
7
5
8
REMOTE
INPUT 1
RGB A OUT
6a
6ba
PIN1 - IN 1
PIN 4 - IN 2
PIN 5 - GND
CONTACT
RGB B OUT
INPUT 2
MONITOR OUT
PVT SW RGB
4
5
7
Figure 2-5 — PVT rear panel features
PVT Series (Rack Mount Models) • Installation
2-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Composite video input (C� and RGB C� models) —
To input a composite video signal from a suitable source,
connect a male RCA plug to this yellow female RCA jack.
a
b
Audio (left and right) input (C� and RGB C� models) —
For unbalanced left and right audio input, insert male RCA
plugs from the audio source, into these two female RCA jacks
(white = left, red = right).
Tip (Signal)
Right Channel
(Red Jacket)
Sleeve (Gnd )
Left Channel
(White Jacket)
Tip (+)
Sleeve (
)
Figure 2-6 — RCA audio connectors
Composite video/audio output (C� and RGB C� models) —
For composite video and audio output, using TP cable, connect
this RJ-45 female output port to one of the two composite
video RJ-45 input connectors (labeled 3 and 4), on the rear panel
of the PVS 204SA switcher (see figure 2-8).
c
Cable termination for composite video and audio transmission
The PVT cable termination method is specific for PVT
transmitters working with the PVS 204SA switcher.
DO NOT connect these devices to an MTP system.
N
N
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
For composite video signals, the RJ-45 connector must
be wired exactly as shown in figure 2-7, so that the input
video and audio signals are transmitted correctly.
2-9
PVT Series (Rack Mount Models) • Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
Clip Down
Side
Pins 12345678
RJ-45
TP Cable and
CAT 5 connector
connector
Composite
568A
Video and Audio signal
Pin
Wire color
1
White-green
Green
Video +
Video –
12345678
2
3
4
5
White-orange
Blue
+ 5 VDC
Audio L +
Audio L –
GND
White-blue
Twisted
pairs
6
7
8
Orange
White-brown
Brown
Audio R +
Audio R –
1&2
7&8
3&6 4&5
Figure 2-7 — Wiring the twisted pair composite
video and audio cable
PVT CV
PVT RGB CV
PVS 204SA
RGB A OUT
AUDIO
IN
AUDIO
IN
AUDIO IN
VIDEO
3
L
L
VIDEO
IN
COMPUTER IN
VIDEO
IN
R
R
TP cable from
PVT Output
VIDEO OUT
RGB B OUT
VIDEO OUT
Rear Panel
Rear Panel
TP cable from
PVT Output
4
Composite Video Input Connectors
on Rear Panel of PVS 204SA
Figure 2-8 — Connecting the PVT composite video
outputs to the PVS 204SA switcher
Audio input (RGB C�, RGB and SW RGB models) —
d
AUDIO IN
Plug a 3.5 mm stereo audio plug into this jack for
unbalanced audio input. Wire the plug as shown in
figure 2-9.
N
Figure 2-9 shows a typical audio connector, which
consists of tip, ring, and sleeve.
Tip (L)
Ring (R)
Sleeve (
)
Figure 2-9 — 3.5 mm stereo audio plug
PVT Series (Rack Mount Models) • Installation
2-10
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB video input (RGB C�, RGB, and SW RGB models) —
Connect a computer video source to this 15-pin HD
connector for high resolution RGB video input.
e
ä
RGB cable A output (RGB C�, RGB, and SW RGB models) —
Using TP cable, connect this RJ-45 female output port,
labeled "RGB A out", to one of the two input ports
(labeled 1A and 2A) on the PVS 204SA switcher.
RGB cable B output (RGB C�, RGB, and SW RGB models) —
Using TP cable, connect this RJ-45 female output port,
labeled "RGB B out", to one of the two input ports
(labeled 1B and 2B) on the PVS 204SA switcher.
ã
Cable termination for RGB video and audio transmission
The PVT cable termination method is specific for PVT
transmitters working with the PVS 204SA switcher.
DO NOT connect these devices to an MTP system.
N
N
N
RJ-45 termination with CAT 5, CAT 5e, CAT 6, and
Skew-Free A/V UTP cable must comply with the
TIA/EIA T 568A wiring standards for all connections.
For RGB signals, the RJ-45 connectors must be wired
exactly as shown in the figure 2-10, using the same
wiring table for both ends, so that the correct input
signal (video on cable A and audio on cable B) is carried.
Cable B carries the audio signal, the vertical sync
information, and 5 VDC to power the PVT transmitters.
N
Clip Down
Side
Pins 12345678
RJ-45
TP Cable and
CAT 5 Connector
Connector
568A
Pin Wire Color
Cable B
Cable A
1
2
3
4
5
White-green
Green
V. sync +
V. sync –
+ 5 VDC
Audio L +
Audio L –
Red +
Red –
12345678
White-orange
Blue
H. sync +
Green +
Green –
H. sync –
Blue +
White-blue
Twisted
Pairs
6
7
8
Orange
GND
White-brown
Brown
Audio R +
Audio R –
Blue –
1&2
7&8
3&6 4&5
Figure 2-10 — Wiring twisted pair cables A and B
2-11
PVT Series (Rack Mount Models) • Installation
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation, cont’d
PVT SW RGB
REMOTE
INPUT 1
TP Cable from
RGB A OUT
TP Cable from
output A
output A
PVS 204SA
PVT RGB
PIN 1 — IN
PIN 4 — IN
PIN 5 — GND
1
2
CONTACT
RGB A OUT
INPUT 2
RGB
1A
2A
I
N
P
U
T
S
RGB B OUT
MONITOR OUT
MONITOR OUT
POWER
Rear
Panel
RGB B OUT
1B
2B
Rear Panel
TP Cable from
output B
12V
3A MAX
TP Cable from
output B
RGB Input Connectors on
Rear Panel of PVS 204SA
Figure 2-11 — Connecting RGB outputs A and B to
the PVS 204SA switcher
MONITOR OUT
Monitor output (RGB and SW RGB models) —
Connect a local monitor device to this 15-pin HD
connector to view the video input.
g
The PVT SW RGB allows the user to view the image
from input 1 only or, by adjusting the front panel DIP
switch, to view the image from either input 1 or input 2.
N
Remote contact closure connector (SW RGB model only) —
Connect a contact closure device to this 15-pin HD connector
to switch between input 1 and input 2 video signals. The
connector has the pin assignments as shown in the table below.
h
Pin
Function
1
2
3
4
5
6
7
8
9
Input #1
Not used
Not used
Input #2
Ground
Not used
Not used
Not used
Not used
REMOTE
PIN 1 — IN 1
PIN 4 — IN 2
PIN 5 — GND
CONTACT
PVT Series (Rack Mount Models) • Installation
2-12
Download from Www.Somanuals.com. All Manuals Search And Download.
PVT Series (Rack Mount Models)
Appendix A
A
Reference Material
Specifications
Part.Numbers
Optional.Accessories
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Material
Specifications
N
These transmitters are compatible only with the Extron
PVS 204SA. They are not compatible with other models of
twisted pair receivers.
Video — RGB (RGB models)
Gain ................................................ Unity
Video input and loop-through — RGB (RGB models)
Number/signal type..................... 1 VGA-UXGA RGBHV, RGBS
(2 for PVT SW RGB, and 1 buffered loop
through)
Connectors ..................................... 1 female 15-pin HD (2 for PVT SW RGB)
Nominal level ................................ 0.7 Vp-p for RGB
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset
Impedance ..................................... 75 ohms
Horizontal frequency.................... 15 kHz to 130 kHz
Vertical frequency.......................... 30 Hz to 150 Hz
Return loss ..................................... <-30 dB @ 5 MHz
DC offset (max. allowable)........... 250 mV
Video output — RGB (RGB models)
Number/signal type..................... 2 analog proprietary signals
Connectors .................................... 2 female RJ-45
Sync — RGB (RGB models)
Input type ...................................... RGBHV, RGBS
Input level ..................................... 3.5 V to 5.5 Vp-p, unterminated
Input impedance .......................... 510 ohms
Max. input voltage........................ 5.5 Vp-p
Video — composite video (CV models)
Gain ................................................ Unity
Differential phase error ............... <1.0º at 3.58 MHz and 4.43 MHz
Differential gain error .................. <1.0% at 3.58 MHz and 4.43 MHz
Video input — composite video (CV models)
Number/signal type..................... 1 composite video
Connectors .................................... 1 female RCA
Nominal level ................................ 1 Vp-p for composite video
Minimum/maximum levels........ Analog: 0.3 V to 1.5 Vp-p with no offset
PVT Series (Rack Mount Models) • Reference Material
A-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Impedance ..................................... 75 ohms
Return loss ..................................... <-30 dB @ 10 MHz
DC offset (max. allowable)........... 100 mV
Video output — composite video (CV models)
Number/signal type..................... 1 analog proprietary signal
Connectors .................................... 1 female RJ-45
Sync — composite video (CV models)
Standards........................................ NTSC 3.58, NTSC 4.43, PAL, SECAM
Audio input
Number/signal type..................... 1 stereo, unbalanced (2 for PVT SW RGB)
Connectors
RGB models ....................... (1) 3.5 mm mini audio jack (tip, ring,
sleeve), (2 for PVT SW RGB)
CV models.......................... 1 pair female RCA
Impedance ..................................... >10k ohms unbalanced, AC coupled
Nominal level ................................ -10 dBV (316 mVrms)
Maximum level ............................. +11 dBV, (unbalanced) at 1% THD+N
N
0 dBu = 0.775 Vrms, 0 dBV =1 Vrms, 0 dBV ≈ 2 dBu
Audio output to a PVS 204SA
Number/signal type .................... 1 analog proprietary signal
Connectors .................................... 1 female RJ-45
General
External power supply................. Remote power from PVS 204SA
Power input requirement............. 5 VDC, TBD A
Rack mount
PVT CV
PVT RGB
PVT SW RGB
PVT RGB CV...................... Yes, with optional 1U rack shelf,
part # 60-190-01, or Versa Tools rack shelf,
part # 60-190-02 or 60-604-20.
Furniture mountable with optional
part # 70-212-01
Enclosure type .............................. Metal
PVT Series (Rack Mount Models) • Reference Material
Download from Www.Somanuals.com. All Manuals Search And Download.
A-3
Reference Material, cont’d
Enclosure dimensions
PVT CV
1/8 rack Versa Tools.... 1.7" H x 2.2" W x 3.0" D
4.3 cm H x 5.6 cm W x 7.6 cm D
PVT RGB, PVT SW RGB, PVT RGB CV
1/4 rack Versa Tools.... 1.7" H x 4.3" W x 3.0" D
4.3 cm H x 10.9 cm W x 7.6 cm D
(Depths excludes connectors.)
Product weight .............................. 1 lbs (0.5 kg).
Shipping weight ............................ 2 lbs (1 kg)
Vibration ........................................ ISTA 1A in carton
(International Safe Transit Association)
Listings............................................ UL, CUL
Compliances................................... CE, FCC Class A, VCCI, AS/NZS, ICES
MTBF............................................... 30,000 hours
Warranty ........................................ 3 years parts and labor
N
N
All nominal levels are at 10%.
Specifications are subject to change without notice.
Part Numbers
Item
Part number
60-827-01
PVT CV
PVT RGB
60-821-01
PVT RGB CV
PVT SW RGB
60-828-01
60-826-01
Included Parts
Included parts
Replacement
part number
Tweeker (small screwdriver)
Rubber feet
User’s manual
PVT Series (Rack Mount Models) • Reference Material
A-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional Accessories
Item
Part number
70-212-01
70-367-01
60-190-20
60-604-20
60-190-01
60-604-01
60-111-01
26-569-xx
26-570-xx
26-637-35
26-637-50
26-637-75
26-637-100
MBU 123, under desk mounting kit
MBB 100, back of rack mounting kit
RSF 123, 3.5" deep rack shelf mounting kit
RSB 123, 3.5" deep basic rack shelf mounting kit
RSU 129, 9.5" deep rack shelf mounting kit
RSB 129, 9.5" deep basic rack shelf mounting kit
KP 6 Keyboard remote control
Enhanced Skew-Free A/V UTP cables
Enhanced Skew-free A/V UTP cables-plenum
CAT 5 cable, 35', plenum
CAT 5 cable, 50', plenum
CAT 5 cable, 75', plenum
CAT 5 cable, 100', plenum
A-5
PVT Series (Rack Mount Models) • Reference Material
Download from Www.Somanuals.com. All Manuals Search And Download.
Reference Material, cont’d
This page was deliberately left blank.
PVT Series (Rack Mount Models) • Reference Material
A-6
Download from Www.Somanuals.com. All Manuals Search And Download.
FCC Class A Notice
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his own expense.
Note: This unit was tested with shielded cables on the peripheral devices. Shielded
cables must be used with the unit to ensure compliance.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Extron’s Warranty
Extron Electronics warrants this product against defects in materials and workmanship
for a period of three years from the date of purchase. In the event of malfunction during
the warranty period attributable directly to faulty workmanship and/or materials,
Extron Electronics will, at its option, repair or replace said products or components,
to whatever extent it shall deem necessary to restore said product to proper operating
condition, provided that it is returned within the warranty period, with proof of
purchase and description of malfunction to:
USA, Canada, South America,
and Central America:
Extron Electronics
Europe, Africa, and the Middle East:
Extron Electronics, Europe
Beeldschermweg 6C
1001 East Ball Road
3821 AH Amersfoort
Anaheim, CA 92805, USA
The Netherlands
Asia:
Japan:
Extron Electronics, Asia
135 Joo Seng Road, #04-01
PM Industrial Bldg.
Singapore 368363
Extron Electronics, Japan
Kyodo Building,
16 Ichibancho
Chiyoda-ku, Tokyo 102-0082
Japan
This Limited Warranty does not apply if the fault has been caused by misuse, improper
handling care, electrical or mechanical abuse, abnormal operating conditions or non-
Extron authorized modification to the product.
If it has been determined that the product is defective, please call Extron and ask for an
Applications Engineer at (714) 491-1500 (USA), 31.33.453.4040 (Europe), 65.6383.4400
(Asia), or 81.3.3511.7655 (Japan) to receive an RA# (Return Authorization number). This
will begin the repair process as quickly as possible.
Units must be returned insured, with shipping charges prepaid. If not insured, you
assume the risk of loss or damage during shipment. Returned units must include the
serial number and a description of the problem, as well as the name of the person to
contact in case there are any questions.
Extron Electronics makes no further warranties either expressed or implied with respect
to the product and its quality, performance, merchantability, or fitness for any particular
use. In no event will Extron Electronics be liable for direct, indirect, or consequential
damages resulting from any defect in this product even if Extron Electronics has been
advised of such damage.
Please note that laws vary from state to state and country to country, and that some
provisions of this warranty may not apply to you.
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2007 Extron Electronics. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|
