EverFocus Security Camera ED560 User Manual

Volume

EverFocus

Operation Instruction

1/3” CCD Outdoor Day/Night Vandal-

Resistant Dome Camera

ED560

Download from Www.Somanuals.com. All Manuals Search And Download.

11. Never push objects of any kind into his appliance through cabinet slots as they may touch dangerous

voltage points or short out parts that could result in fire or electric shock.

12. Refer all work related to the installation of this product to qualified service personnel or system installers.

Federal Communication Commission Interference

Statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance

could void the user's authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

1. Product Overview……………………………………………6

1.1 Features ............................................................................ 7

1.2 Accessory Parts List ........................................................ 8

1.3 Specifications ................................................................. 10

1.4 Dimensions...................................................................... 11

1.5 Camera Component Description .................................... 12

1.6 Front and Back Panel Layout.......................................... 13

1.7 Related Products ............................................................ 15

2. INSTALLATION………………………………………………16

2.1 Mounting Camera............................................................ 17

2.1 .1 Drill the Holes ........................................................ 17

2.1.2 Mounting ................................................................. 19

2.2 Adjusting Camera ........................................................... 21

2.2.1 Adjusting Camera Position ..................................... 21

2.2.2 Adjusting Zoom and Focus ..................................... 22

2.2.3 Camera Setting............................................................ 24

2.2.3.1 OSD User Setup Menu..................................... 24

2.2.4 Close the Camera Cover ......................................... 25

3. OSD Menu & Configuration………………………………28

Download from Www.Somanuals.com. All Manuals Search And Download.

3.1 OSD Menu Setup ............................................................. 28

3.1.1 LENS........................................................................ 29

3.1.2 Shutter ................................................................... 29

3.1.3 White Balance Control............................................ 31

3.1.4 BACKLIHGT............................................................. 32

3.1.5 AGC (Auto Gain Control)......................................... 33

3.1.6 DNR (Dynamic Noise Reduction) ............................ 34

3.1.7 SENS-UP.................................................................. 35

3.1.8 SPECIAL .................................................................. 36

3.1.8.1 CAMERA ID...................................................... 37

3.1.8.2 COLOR ADJ ..................................................... 38

3.1.8.3 SYNC ............................................................... 38

3.1.8.4 MOTION DETECTION....................................... 39

3.1.8.5 PRIVACY.......................................................... 42

3.1.8.6 MIRROR ........................................................... 44

3.1.8.7 SHARPNESS .................................................... 45

3.1.8.8 RESET.............................................................. 45

3.1.8.9 RETURN........................................................... 46

3.1.9 EXIT......................................................................... 46

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

Chapter

Product Overview

The new ED560 is designed with the advanced 16-bit Digital Signal Processor (DSP) for powerful

processing capability to show 560TVL horizontal resolution. Designed with SENS-UP 128X slow

shutter technology, ED560 captures images in almost darkness with super high sensitivity of

0.002lux. With 3-Axis rotation, ED560 offers quick and flexible wall or ceiling installation. In

addition, ED560 is weatherproof IP66 rated, vandal resistant to avoid any intentional destruction.

ED560 is ideal for 24/7 surveillance in all outdoor application. It is available in model with or

without True Day/Night function.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

1.1 Features

1/3” SONY Super HAD CCD for excellent picture quality

560TVL of horizontal resolution with the advanced 16-bit Digital Signal Processor (DSP)

ED560 captures clear images in almost darkness with 0.002 Lux

SENS-UP Slow Shutter 128X max.

True Day/Night function with removable IR cut filter (ED560T)

Built-in DNR (Dynamic Noise Reduction) for noise reduction and a 70% saving of disk

storage

3-Axis rotation

Easy wall or ceiling installation

OSD setting menu

Support Motion Detection function

Support Privacy function

Vandal resistant

Weatherproof IP66 rated

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

1.2 Accessory Parts List

Please be careful when you unpack the box due to the electronics devices inside. Check and make sure

that you have all the items listed below inside the original box:

• Camera Unit x 1

• Operation Manual x 1

• Mounting kit includes:

-Long Screws x 3 (for mounting base)

-Expanding Screws x 3

-Washer x 3

• Circle Installation Sticker x 1

• Video Cable x 1

• Extension Power Cable x 1

• Desiccant Pack x 1

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

• Focus Aiding Lens Cap(for 9~22mm models only) x 1

Please Note: If an item appears to have been damaged in shipment, replace it properly in its carton and

notify the shipper. If any items are missing, notify your EverFocus Electronics Corp. Sales Representative or

Customer Service. The shipping carton is the safest container in which the unit may be transported. Save it

for possible future use.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

1.3 Specifications

Items

Parameter

Pickup Device

Video Format

Scanning System

1/3” SONY Super HAD CCD

NTSC or PAL

NTSC:525 TVL, 60 fields/sec

PAL:625 TVL, 50 fields/sec

768 x 494(NTSC); 752 x 582 (PAL)

560 TVL

Picture Elements

Horizontal Resolution

Sensitivity

0.002Lux (SENS-UP 128x) ; 0.25Lux/ F=1.2

Over 50 dB(AGC off )

S/N Ratio

Electronic Shutter

Lens Type

1/50(1/60)~1/100,000

Vari-focal lens, Auto Iris

f=2.9~10mm/F=1.2 ;f=9~22mm/F=1.6

*Lens models and availability vary in different regions

Off/Low/Middle/High Adjustable

ATW(2500 °K ~8300 °K)/AWC/Manual

0.45

Back Light Comp.

Auto Gain Control

Auto White Balance

Gamma Correction

True Day & Night

Yes

Flickerless

Yes

Video Output

2 video outputs

BNC 1.0Vp-p, 75ohm

Additional testing video output 1.0Vp-p, 75ohm

Sync. Mode

Line Lock/Internal sync.

H-Mirror

Yes

OSD Menu

Yes

Vandal Resistant

Power Source

Power Consumption

Yes

12VDC/24VAC

24VAC 5VA max

12VDC 3.5W max

Dimensions

123mm(O.D.) x 107.8mm (H) ; 4.8” (O.D.) x 4.2” (H)

Weight

0.74 kg / 1.6 lbs

Operating Temperature

Weatherproof

-10°C~50°C ; 14°F~122°F (20%~80% Humidity)

IP66

Download from Www.Somanuals.com. All Manuals Search And Download.

P R O D U C T O V E R V I E W

^{C H}C^Aer^Pti^Tfic^Eat^Rions

FCC/CE

1.4 Dimensions

123mm x 107.8mm ; 4.8” x 4.2”

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

1.5 Camera Component Description

Base

Outer Cover ring

Rotatable cover

First-Axis Joint for

ceiling mounting

Third-Axis Joint

Second-Axis Joint

for wall mounting

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

Video out

Down

Adjustment

button

Power input

Video output

1.6 Front and Back Panel Layout

Front Panel Layout:

Internal Sensor

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

Back Panel Layout:

(3)

(5)

Video

Down

(1)

(7)

(6)

(2)

(4)

(1) Power Input Terminal & Video Output Connector

Connect to the appropriate power to each model. Video Output connector is for connecting the

video output of the camera to a color monitor or other video devices through a 75 Ohm type coaxial

cable with BNC female connector at backside of the camera.

(2) Second Video Output Connector

When installing the camera, you can use second video connector to connect a portable monitor, this

will allow you to easily adjust camera’ angle.

(3) Up: Adjust the switch to move the cursor upwards. This is used to select the item need to be set.

(4) Down: Adjust the switch to move the cursor downwards. This is used to select the item need to be

set.

(5) Right: Adjust the switch to right direction. This is used to select or adjust the parameters of the

selected item.

(6) Left: Adjust the switch to left direction. This is used to select or adjust the parameters of the

selected item.

(7) Set button: This button is used to enter setup menu. If the item has its own setting menu (sign

), press this button again to display the setup menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

P R O D U C T O V E R V I E W

1.7 Related Products

In addition, you may order the following EverFocus products which are recommended for use with the

camera to achieve the best performance:

• L Type Bracket

• EN220 5.6 inch LCD Test Monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

Chapter

Installation

This chapter will describe, in general terms, how to install the ED560 camera.

STEPS:

2.1. Mounting Camera:

1. Drill the Holes. See 2.1.1

2. Mounting: See 2.1.2

2.2. Adjusting Camera:

1. Adjust the camera position. See 2.2.1

2. Adjusting Zoom and Focus See 2.2.2

3. Camera Setting. See 2.2.3

4. How to close camera cover after installation. See 2.2.4

Warning

•

To prevent electrical shock, turn off the electrical power before making electrical connections.

Do not expose the appliance to water or moisture, nor try to operate it in wet areas.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2.1 Mounting Camera

2.1 .1 Drill the Holes

1. Paste the drilling template on the ceiling or wall

2. Use the tool to drill 4 holes, 3 for screw A, B and C,

1 for power/video cable.

Screw hole A

Screw hole C

Installation sticker

Screw hole B

Outlet hole

Power/Video Cable

Screw

A,B,C

Camera base

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

3. Pull the cables to be connected to power and video cables from ceiling or wall.

Power input

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2.1.2 Mounting

1. Take off camera’s cover.

Loose outer cover ring first

Take off camera’s cover.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2. Fix the camera base to ceiling or wall by using 3 screws.

Ceiling Mount:

Wall Mount:

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2.2 Adjusting Camera

2.2.1 Adjusting Camera Position

Adjust the camera to best angle for viewing.

When you install on the

ceiling, Change angle of

view by turning this joint

Module can be adjusted up and down

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2.2.2 Adjusting Zoom and Focus

It is highly recommended to use Everfocus Test Monitor to test the camera. Find the second Video

testing connection at back panel. Connect it with video cable in the package.

Power input

Video out

Connect with Test Monitor

1 .Loosen the zoom ring knob, and then turn the ring towards <W> or <T> as necessary to obtain the

desired view range.

W side (Zoom out)

The viewing range will be wider and the subject is smaller.

T side (Zoom in)

The viewing range will be smaller and the subject is larger.

2. Loosen the focus ring knob, then turn the ring towards <∞> or <N> as necessary to obtain the

clear video image.

3. Repeat steps 1 and 2 until the best image is obtained. Once the lens setting is finished, tighten the

zoom ring and the focus ring knobs.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

Important Note when focusing a 9-22mm Lens

To adjust lens zoom and focus, if using the 9~22mm lens model of ED560 series cameras, the

focus aiding lens cap must be used to simulate the dome being closed. Follow the steps below

to ensure that camera will stay in focus.

Step 1 Take the included focus aiding lens cap (shown below) from its small plastic bag.

Step 2 Open dome cover and place the Focus aiding lens cap on the lens making sure that the

caps notch is resting on the zoom knob.

Step3 With cap on, adjust the focus and zoom rings by loosening the knobs and turning the

rings until subject is in focus. Retighten the knobs when done.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

Step4 When finished adjusting focus and zoom, remove the focus aiding cap from the camera

lens, replace the the dome cover and tighten the tamperproof screws with provided

wrench.

NOTE: If necessary, you can put desiccant pack in bracket side. Using cable to fix it before place the

cover back to camera.

Desiccant Pack

2.2.3 Camera Setting

2.2.3.1 OSD User Setup Menu

This camera utilizes an On Screen Display (OSD) user setup menu.

Please refer to Chapter 3 OSD Menu & Configuration, to get more detail about OSD menu steps.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

2.2.4 Close the Camera Cover

ED560 is specially designed with one inner cover and one outer cover ring for water-proof and user-friendly

installation purpose. Please follow the instruction for closing the camera cover.

1. Aim the lens to window of cover.

2. Push the interior cover until it completely covers the whole red gasket and line up with camera base

parallel. The cover need to align with camera base otherwise it cannot be closed. Then tighten the

outer cover ring tightly to the camera base.

Push the inner cover and

cover the whole red

gasket

Outer cover ring

Download from Www.Somanuals.com. All Manuals Search And Download.

Correct

Wrong (not aligned)

Wrong (red gasket

not covered)

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

I N S T A L L A T I O N

3. If the lens did not aim the window. Slightly adjust the inner cover to have the lens aimed exactly at

window.

Slightly adjust the cover

4. Tighten the outer cover ring until it is firmly fixed.

Turn the external ring

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

Chapter

OSD Menu & Configuration

This chapter introduces how to configure the camera OSD menu.

STEPS

1. Configure the camera, please refer to OSD Menu Setup

3.1 OSD Menu Setup

Please make sure control key selection switch is at OSD position.

Note: OSD menu only requires one click and you should see the following menu.

SETUP

> LENS

SHUTTER

DC <┘

___

WHITE BAL.

BACKLIGHT

AGC

ATW

OFF

MIDDLE

LOW

DNR

SENS-UP

SPECIAL <┘

EXIT

AUTO <┘

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

3.1.1 LENS

1. When the SETUP menu is displayed on the screen, please direct the arrow to point to “LENS” by

turning the mini-joystick UP (c) or DOWN (d). Press the mini-joystick to adjust IRIS level (the

higher is brighter). In most cases, you don’t need to adjust this, since Lens is Auto Iris supported.

SETUP

> LENS

SHUTTER

DC <┘

___

LENS

|+++++++++| 25

WHITE BAL.

BACKLIGHT

AGC

ATW

LEVEL

OFF

MIDDLE

LOW

DNR

SENS-UP

SPECIAL <┘

EXIT

AUTO <┘

NOTE: Since DC lens is a built-in lens for EZ550 camera, it does not support Manual lens, please do

not select lens as Manual mode, it disables sens-up and may cause malfunction of lens.

2. Please press the mini-joystick for saving setting and return to the previous menu.

3.1.2 Shutter

1. When the SETUP menu is displayed on the screen, please direct the arrow to point to

“SHUTTER” by turning the mini-joystick DOWN (d).

2. Select the shutter mode by turning the mini-joystick LEFT (e) or RIGHT (f).

Three modes are available. FLK, ESC and Manual.

NOTE:

Since DC lens is a built-in lens for EZ550 camera, shutter does not support ESC and Manual functions.

ESC and Manual are reserved functions, please do not select these two options in normal situation.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

Ö FLK: Please select “FLK” mode when flickering occurs on the screen, which is caused by an

irregular balance between illumination and frequency. NTSC model: 1/100, PAL model:

1/120.

SETUP

LENS

MANUAL

FLK

> SHUTTER

WHITE BAL.

BACKLIGHT

AGC

ATW

OFF

MIDDLE

LOW

DNR

SENS-UP

SPECIAL <┘

EXIT

___

Ö ESC (Reserved).

SETUP

BRIGHTNESS

LENS

MANUAL

ESC <┘

ATW

> SHUTTER

WHITE BAL.

BACKLIGHT

AGC

BRIGHTNESS |+++++++++|

OFF

MIDDLE

LOW

AUTO <┘

DNR

SENS-UP

SPECIAL <┘

EXIT

Ö Manual (Reserved).

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SETUP

SHUTTER

LENS

MANUAL

MANUAL <┘

ATW

> SHUTTER

WHITE BAL.

BACKLIGHT

AGC

> MANUAL 1/50

OFF

MIDDLE

LOW

___

DNR

SENS-UP

SPECIAL <┘

EXIT

3. Press the mini-joystick when you finish all the settings.

NOTE:

○ With DC lens, the shutter speed is fixed as 1/60 for NTSC and 1/50 for PAL.

3.1.3 White Balance Control

The screen color can be adjusted by using the WHITE BALANCE function.

1. Please direct the arrow to point to “WHITE BAL” on the SETUP menu by turning the mini-

joystick UP (c) or DOWN (d).

2. Please select the mode you would like to operate by turning the mini- joystick LEFT (e) or

RIGHT (f).

Please select one of the 3 modes below:

Ö ATW (Auto Tracking White Balance): This mode can be used within the color temperature range

from 2,500°K to 8,300°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels).

Ö AWC (Auto White Balance Control): Press mini-joystick while the camera is directed at a piece of

white paper to get the optimum state under the present illumination. If the environment and the

light source are changed, you need to adjust the white balance again.

Ö MANUAL: The manual adjustment mode enables a more precise adjustment. Please select ATW

or AWC first. Then change to manual adjustment mode and press mini-joystick. Set the suitable

color temperature, and increase or decrease the red and blue color values at the same time while

checking the color changes of the object.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SETUP

WHITE BAL.

|+++++++++| 32

LENS

DC <┘

___

SHUTTER

> WHITE BAL.

BACKLIGHT

AGC

RED

BLUE

MANUAL <┘

OFF

|+++++++++| 39

MIDDLE

LOW

AUTO <┘

DNR

SENS-UP

SPECIAL <┘

EXIT

NOTE:

Under the following conditions, the WHITE BALANCE function may not operate well. In

such cases, please select the AWC mode.

○ When the object’s surroundings have a high color temperature.

○ When the object’s surroundings are dark.

○ If the camera faces a fluorescent light directly or is installed in a place where the

illumination changes constantly, the WHITE BALANCE function may become unstable.

3.1.4 BACKLIHGT

Even there is a massive backlight behind the object, bright images of the background and the object

can still be obtained by using the BACKLIGHT function.

1. Please direct the arrow to point to “BACKLIGHT” on the SETUP menu by turning the mini-

joystick UP (c) or DOWN (d).

2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SETUP

LENS

DC <┘

___

SHUTTER

WHITE BAL.

> BACKLIGHT

AGC

ATW

OFF

MIDDLE

LOW

DNR

SENS-UP

SPECIAL <┘

EXIT

AUTO <┘

Ö HIGH: The gain increases from 0dB up to 42dB.

Ö MIDDLE: The gain increases from 0dB up to 30dB.

Ö LOW: The gain increases from 0dB up to 18dB.

Ö OFF: BACKLIGHT function does not operate.

3.1.5 AGC (Auto Gain Control)

1. Please direct the arrow to point to “AGC” on the SETUP menu by turning the mini-joystick UP (c)

or DOWN (d).

2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).

The more the level of gain increases, the brighter the screen and the level of noise increases as well.

Ö HIGH: The gain increases from 6dB up to 42dB.

Ö MIDDLE: The gain increases from 6dB up to 30dB.

Ö LOW: The gain increases from 6dB up to 18dB.

Ö OFF: The gain is fixed at 6dB.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SETUP

LENS

DC <┘

___

SHUTTER

WHITE BAL.

BACKLIGHT

> AGC

DNR

SENS-UP

SPECIAL <┘

EXIT

ATW

OFF

MIDDLE

LOW

AUTO <┘

3.1.6 DNR (Dynamic Noise Reduction)

Dynamic Noise Reduction in video images has the following effects.

1. Images are brighter and sharper.

2. When the level of noise is reduced, the performance of a camera can apparently be improved.

3. When it is recorded digitally, reduced noise can reduce image file size.

As the level of gain changes, the background noise in the low light level automatically decreases.

1. Please direct the arrow to point to “DNR” on the SETUP menu by turning the mini-joystick UP

2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).

SETUP

LENS

DC <┘

___

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

ATW

OFF

MIDDLE

LOW

> DNR

SENS-UP

SPECIAL <┘

EXIT

AUTO <┘

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

Ö OFF: No reduction in noise level.

Ö LOW: Little reduction in noise level with nearly no ghost image. Default value is LOW.

Ö MIDDLE: Just enough reduction in noise levels without causing much ghost imaging.

Ö HIGH: Huge reduction in noise level, which may cause much ghost imaging.

NOTE:

When AGC is turned off, DNR will be disabled.

3.1.7 SENS-UP

SENS UP is used to keep a brilliant, vivid screen image by automatically detecting changes in the level

of light under low light level conditions. The value is from x2 ~x128.

1. Please direct the arrow to point to “SENS UP” on the SETUP menu by turning the mini-joystick

UP (c) or DOWN (d).

2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).

Ö AUTO: Low light level auto mode. Default value is AUTO (Up to X 10).

SETUP

LIMIT

LENS

DC <┘

___

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

> AUTO

X 10

ATW

OFF

MIDDLE

LOW

DNR

> SENS-UP

SPECIAL <┘

EXIT

AUTO <┘

Ö OFF: The function is disabled.

3. Press the mini-joystick when you finish all the settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

NOTE:

○ The maximum storage magnification in low light level movement situations can be

adjusted by pressing the mini-joystick in “AUTO” mode.

○ The screen becomes brighter when the magnification increases; yet the after image

increases as well.

○ Please be noted that spots and noise may appear if storage magnification increases when

SENS-UP is operating. This is a normal phenomenon.

3.1.8 SPECIAL

1. Please direct the arrow to point to “SPECIAL” on the SETUP menu by turning the mini-joystick

UP (c) or DOWN (d).

SETUP

LENS

DC <┘

___

SHUTTER

WHITE BAL.

BACKLIGHT

AGC

ATW

OFF

MIDDLE

LOW

DNR

SENS-UP

> SPECIAL <┘

EXIT

AUTO <┘

2. Select the mode you would like to operate by turning the mini-joystick LEFT (e) or RIGHT (f).

SPECIAL

> CAMERA ID

COLOR ADJ. <┘

SYNC.

OFF

INT

MOTIION DET OFF

PRIVACY

MIRROR

SHARPNESS

RESET

OFF

ON <┘

RETURN <┘

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

3.1.8.1 CAMERA ID

Input the camera ID, and it will be appeared on the monitor.

1) Please direct the arrow to point to “CAMERA” by turning the mini-joystick UP (c) or DOWN

(d).

2) Select “ON” by turning the mini-joystick LEFT (e) or RIGHT (f).

3) Press the mini-joystick.

4) Maximum 15 letters can be used for the ID.

¾ Turning the mini-joystick UP (c), DOWN (d), LEFT (e) or RIGHT (f) to select the letters.

¾ Press the mini-joystick to lock in the letters.

5) Once a name has been selected, please choose a position where you would like to display the name.

¾ Move the cursor onto “POS” and press the mini-joystick.

¾ The name will appear at the top left hand corner.

¾ Please use the 4 directional buttons to find the desired position to display the name.

6) If you would like to cancel the ID inputted, please move the cursor to “CLR”, and all the letters

inputted will be deleted.

7) Select “END” and press the mini-joystick to complete ID input.

SPECIAL

> CAMERA ID

COLOR ADJ. <┘

SYNC.

INT

MOTIION DET OFF

PRIVACY

MIRROR

OFF

SHARPNESS

RESET

ON <┘

RETURN <┘

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

C A M E R A

I D

A B C D E F G H I J K L M

N O P Q R S T U V W X Y Z

a b c d e f g h

n o p q r s t u v w x y z

─ · 0 1 2 3 4 5 6 7 8 9

l m

C L R

P O S

E N D

←

→

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _

3.1.8.2 COLOR ADJ

Adjust the Color Gain from 0 ~ 15

SPECIAL

COLOR GAIN.

|++++++++| 8

CAMERA ID

> COLOR ADJ. <┘

SYNC.

OFF

INT

> LEVEL

MOTIION DET OFF

PRIVACY

MIRROR

OFF

SHARPNESS

RESET

ON <┘

RETURN <┘

3.1.8.3 SYNC

There are two SYNCHRONIZATION modes: INTERNAL and EXTERNAL LINE-LOCK. In

LINE-LOCK mode, without a synchronous generator, it synchronizes the video signal between

cameras. The Line-Lock synchronization is only used in the places of 60Hz (NTSC models) or 50Hz

(PAL models).

-INT: Internal synchronization

-LL: External line-lock synchronization

=> If you choose “LL”, you can adjust the phase your wish to set. Then press the mini-joystick. You

can adjust the phase you wish to set from 0 to 359.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SPECIAL

CAMERA ID

OFF

SYNC

|++++++++| 0

COLOR ADJ. <┘

> SYNC.

LL <┘

> PHASE

MOTIION DET OFF

PRIVACY

MIRROR

SHARPNESS ON <┘

RESET

RETURN <┘

OFF

3.1.8.4 MOTION DETECTION

EZ550 enables you to observe movements of objects in 4 different places on the screen, the message

“MOTION DETECTED” appears on the screen when movement is detected; therefore this helps to

improve supervision efficiency. The camera detects an object’s movement by sensing discrepancy of

outline.

1) Please direct the arrow to point to “MOTION DET” by turning the mini-joystick UP (c) or

DOWN (d).

2) Select “ON” by turning the mini-joystick LEFT (e) or RIGHT (f).

3) Press the mini-joystick.

SPECIAL

MOTION DETECTION

CAMERA ID

COLOR ADJ. <┘

SYNC.

OFF

> AEREA SEL

AREA STATE

TOP

AREA1

|+++++++++| 10

INT

> MOTIION DET

PRIVACY

ON <┘

OFF

MIRROR

OFF

DOWN

LEFT

RIGHT

|+++++++++| 25

|+++++++++| 20

|+++++++++| 40

SHARPNESS

RESET

ON <┘

RETURN <┘

Press SET to return

z Please select the area you would like to detect from the 4 areas in AREA SEL mode.

z Please select ON mode for the chosen area.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

z Please turn mini-joystick UP (c) or DOWN (d) to move between TOP, DOWN, LEFT and

RIGHT for adjusting the size of the area.

z Please turn mini-joystick LEFT (e) or RIGHT (f) to adjust the value for size of the area.

AREA1

AREA3

AREA2

AREA4

z Additionally, it is possible to change the position of the area. Please refer to the following

example for detailed steps on moving AREA1 to center.

1. The original position of AREA1 was TOP: 10, DOWN: 25, LEFT: 20 and RIGHT: 40.

AREA1

2. Increase DOWN scale value by 20. AREA1 position after change is: TOP: 10, DOWN: 45, LEFT:

20 and RIGHT: 40.

AREA1

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

3. Increase TOP scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 20

and RIGHT: 40.

AREA1

4. Increase RIGHT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT:

20 and RIGHT: 60.

AREA1

Increase LEFT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 40

and RIGHT: 60.

AREA1

z In order to save the changes and complete the setting, press the mini-joystick. This allows you

to return to the previous menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

3.1.8.5 PRIVACY

This mode covers the areas you do not want to see on the screen.

Please direct the arrow to point to “PRIVACY” by turning the mini-joystick UP (c) or

DOWN (d).

Select “ON” by turning the mini-joystick LEFT (e) or RIGHT (f).

Press the mini-joystick.

SPECIAL

PRIVACY

> AEREA SEL AREA1

CAMERA ID

OFF

COLOR ADJ. <┘

SYNC.

AREA STATE. OFF

INT

OFF

AREA TONE

TOP

|+++++++++| 80

MOTIION DET

|++++++++| 10

|+++++++++| 25

|+++++++++| 20

|+++++++++| 40

> PRIVACY

MIRROR

ON <┘

OFF

ON <┘

DOWN

LEFT

SHARPNESS

RESET

RIGHT

RETURN <┘

z Please select the area you would like to cover from the 4 areas in AREA SEL mode.

z Please select ON mode for the chosen area.

z Please select AREA TONE for cover area color. The smaller the number, the darker the color.

z Please turn the mini-joystick UP (c) or DOWN (d) to move between TOP, DOWN, LEFT

and RIGHT for adjusting the size of the area to be covered.

z Please turn the mini-joystick LEFT (e) or RIGHT (f) to adjust the value for size of the area

to be covered.

AREA1

AREA2

AREA3

AREA4

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

Additionally, it is possible to change the position of the area to be covered. Please refer to the

following example for detailed steps on moving AREA1 to center.

1. The original position of AREA1 was TOP: 10, DOWN: 25, LEFT: 20 and RIGHT: 40.

AREA1

2. Increase DOWN scale value by 20. AREA1 position after change is: TOP: 10, DOWN: 45, LEFT:

20 and RIGHT: 40.

AREA1

3. Increase TOP scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 20

and RIGHT: 40.

AREA1

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

4. Increase RIGHT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT:

20 and RIGHT: 60.

AREA1

5. Increase LEFT scale value by 20. AREA1 position after change is: TOP: 30, DOWN: 45, LEFT: 40

and RIGHT: 60.

AREA1

In order to save the changes and complete the setting, press the mini-joystick. This allows you

to return to the previous menu.

3.1.8.6 MIRROR

-ON: Sets a horizontal image 180 angel inversion.

-OFF: Disable the inversion.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SPECIAL

OFF

CAMERA ID

COLOR ADJ. <┘

SYNC.

INT

MOTIION DET OFF

PRIVACY

> MIRROR

SHARPNESS

RESET

OFF

ON <┘

RETURN <┘

3.1.8.7 SHARPNESS

The contour of the video image becomes cleaner and more distinguishing as the level of SHARPNESS

increases. If the level goes up extremely, it may affect the video image and cause noise.

-ON: Enable the SHARPNESS mode.

-OFF: Disable the SHARPNESS mode.

Please press the mini-joystick.

The available range of level is 0~31.

SPECIAL

SHARPNESS

|+++++++++| 8

CAMERA ID

COLOR ADJ. <┘

SYNC.

OFF

INT

> LEVEL

MOTIION DET OFF

PRIVACY

MIRROR

OFF

> SHARPNESS

RESET

ON <┘

RETURN <┘

3.1.8.8 RESET

Press the mini-joystick on RESET for 3 seconds until it restarts. It will go to factory default value.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

O S D M E N U A N D C O N F I G U R A T I O N

SPECIAL

OFF

CAMERA ID

COLOR ADJ. <┘

SYNC.

INT

MOTIION DET OFF

PRIVACY

MIRROR

SHARPNESS

> RESET

RETURN <┘

OFF

ON <┘

3.1.8.9 RETURN

Press the mini-joystick on RETURN. It saves all settings in SPECIAL menu and returns to the Setup

menu.

SPECIAL

CAMERA ID

COLOR ADJ. <┘

SYNC.

OFF

INT

MOTIION DET OFF

PRIVACY

MIRROR

OFF

SHARPNESS

RESET

ON <┘

> RETURN <┘

3.1.9 EXIT

Press the mini-joystick on EXIT after you finish all the settings. It will return to live image.

NOTE:

If you quit the Menu without pressing EXIT, all the settings you previously did will

NOT be saved.

Download from Www.Somanuals.com. All Manuals Search And Download.

C H A P T E R

C O N T R O L F R O M K E Y B O A R D

Head Office:

Europe Office:

12F, No.79 Sec. 1 Shin-Tai Wu Road,

Hsi-Chih, Taipei, Taiwan

TEL: +886-2-26982334

FAX: +886-2-26982380

www.everfocus.com.tw

Albert-Einstein-Strasse 1

D-46446 Emmerich, Germany

TEL: 49-2822-9394-0

www.everfocus.de

China Office:

USA L.A. Office:

Room 609, Technology Trade Building,

Shangdi Information Industry Base,

Haidian District, Beijing,China 10085

TEL: +86-10-62973336/37/38/39

FAX: +86-10-62971423

1801 Highland Ave. Unit A

Duarte, CA 91010, U.S.A.

TEL: +1-626-844-8888

FAX: +1-626-844-8838

www.everfocus.com

www.everfocus.com.cn

USA N.Y. Office:

Japan Office:

415 Oser Avenue Unit S

Hauppauge, NY 11788

TEL: 631-436-5070

FAX: 631-436-5027

www.everfocus.com

1809 WBG MARIBU East 18F,

2-6 Nakase.Mihama-ku.

Chiba city 261-7118, Japan

TEL: +81-43-212-8188

FAX: +81-43-297-0081

www.everfocus.com

Your EverFocus product is designed and

manufactured with high quality materials

and components which can be recycled and

reused.

Ihr EverFocus Produkt wurde entwickelt und

hergestellt mit qualitativ hochwertigen

Materialien und Komponenten, die recycelt

und wieder verwendet werden können.

Dieses Symbol bedeutet, dass elektrische und

elektronische Geräte am Ende ihrer

Nutzungsdauer vom Hausmüll getrennt

entsorgt werden sollen.

This symbol means that electrical and

electronic equipment, at their end-of-life,

should be disposed of separately from your

household waste.

Please, dispose of this equipment at your

local community waste collection/recycling

centre.

Bitte entsorgen Sie dieses Gerät bei Ihrer

örtlichen kommunalen Sammelstelle oder im

Recycling Centre.

Helfen Sie uns bitte, die Umwelt zu erhalten,

in der wir leben!

In the European Union there are separate

collection systems for used electrical and

electronic product.

Please, help us to conserve the environment

we live in!

P/N: MED5G00600_Ver.B

Download from Www.Somanuals.com. All Manuals Search And Download.

Clarion Car Video System OHM642 User Manual
Creda Dishwasher IDV60 User Manual
Crown Equipment Automobile SHR 5500 Series User Manual
Curtis Digital Photo Frame DPF316 User Manual
Desa Portable Generator Mgh3000 Mgh4000a Mgh5000a Mgh6000 Mgh7000 User Manual
Desa Water Heater CCL3018NA User Manual
Electro Voice Portable Speaker PI94 User Manual
EVGA Computer Hardware 111 CD E630 TR User Manual
GE Monogram Security Camera Security Legend Camera User Manual
Gitzo Camcorder Accessories G1345 User Manual