EAN800A/EAN800AW
User’s Manual
Copyright © EverFocus Electronics Corp,
Release: Dec. 2009 Rev.D
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
EAN800A/EAN800AW complies with CE and FCC.
About this document
All the safety and operating instructions should be read and followed before the
unit is operated. This manual should be retained for future reference. The
information in this manual was current when published. The manufacturer reserves
the right to revise and improve its products. All specifications are therefore subject
to change without notice.
Safety Notice
-These limits are designed to provide reasonable protection. This equipment
generates, uses and can radiated radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures: -Reorient or relocate the receiving antenna.
-Increase these separations between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this appliance to rain or
moisture.
Do not attempt to disassemble the appliance. To prevent electric shock, do
not remove screws or covers. There are no user-serviceable parts inside.
Contact qualified service personnel for maintenance. Handle the appliance with
care. Do not strike or shake, as this may damage the appliance.
Do not use strong or abrasive detergents when cleaning the appliance body.
Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to
3
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
remove, use a mild detergent and wipe gently.
Do not operate the appliance beyond its specified temperature, humidity or
power source ratings. Do not use the appliance in an extreme environment where
high temperature or high humidity exists. Use the appliance at temperature within
0℃ ~ +40℃ / 32 ~ 104 and a humidity below 90%. The input power source for
this appliance is 12 VDC & PoE.
Use only the recommended power supplies. Power supplies must comply
with the requirement of the latest version of IEC60950-1. Substitutions may
damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing
precautions to avoid electrostatic discharge.
Installation should be performed by qualified service personnel only in
accordance with the National Electrical Code or applicable local codes.
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered
trademarks of the respective holders. Other product names appearing in this User's
Guide may be trademarks or registered trademarks of their respective holders.
Java™ and all Java-related logos and trademarks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs repair service, the customer should contact the nearest
EverFocus Electronics Corp. Service Center for return authorization and shipping
instruction.
About AC Adaptor
Specifications for AC adaptor
Power Supply: 12VDC, 1 A
Power Output: 12VDC, 1 A
Operating Temperature: 0 ~ 40 / 32 ~ 104
External Dimensions: 56 mm x 68 mm x 101 mm / 2.24” x 2.72” x 4.04”
4
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
TABLE OF CONTENTS
1. INTRODUCTION....................................................................................................6
2. FEATURES ..............................................................................................................6
3. ACCESSING THE CAMERA MENU ...................................................................7
4. SETTING................................................................................................................10
4.1 SYSTEM INFO ......................................................................................................10
4.1.1 Information .................................................................................................10
4.1.2 Log..............................................................................................................11
4.2 USER CONFIG......................................................................................................12
4.3 NETWORK ...........................................................................................................14
4.3.1 Network.......................................................................................................14
4.3.2 DDNS..........................................................................................................17
4.3.3 Bandwidth...................................................................................................18
4.3.4 SMTP/FTP..................................................................................................19
4.3.5 Network Alarm (reserved for PowerCon)...................................................21
4.3.6 Wireless (EAN800AW)...............................................................................22
4.4 VIDEO .................................................................................................................23
4.4.1 Multi Streaming ..........................................................................................23
4.4.2 Camera........................................................................................................25
4.5AUDIO .................................................................................................................27
4.6 USER .................................................................................................................28
4.7 EVENT...............................................................................................................29
4.7.1 Event ...........................................................................................................29
4.7.2 Motion.........................................................................................................32
4.7.3 Alarm...........................................................................................................33
4.7.4 Time Mask ..................................................................................................34
4.8 SYSTEM............................................................................................................35
4.8.1 Date/Time....................................................................................................35
4.8.2 Daylight Saving ..........................................................................................37
4.8.3 SD Card.......................................................................................................38
4.8.4 Maintenance................................................................................................40
5. SPECIFICATIONS................................................................................................42
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
1. INTRODUCTION
The EAN800A/EAN800AW network camera provides H.264, MPEG-4 and MJPEG
compression for multi-streaming capabilities. H.264 is the most advanced video
compression technology that saves your bandwidth without sacrificing video quality.
Designed with advanced digital processing circuitry for high resolution 1/3'' color
CCD sensor, it can control AGC, BLC, FL, ES, H-Mirror, IRIS Level and Day/Night
function through web browser. Built-in IEEE 802.11b/g wireless connection gives you
the freedom to place the camera where it's needed. EAN800A/EAN800AW is the
most flexible IP solution for all your application needs.
2. FEATURES
z
z
z
z
Built-in H.264, MPEG-4 and MJPEG digital signal output at Full D1 image size
with up to 30fps.
H.264/MPEG4/MJPEG multi stream output for simultaneous live monitoring
and high resolution recording.
Support 4 independent video streams that can provide different compression
formats and resolutions.
The high sensitivity of 0.4Lux/F=1.2 is achieved by using the advanced
1/3”Sony Super HAD color CCD.
z
z
z
z
Power over Ethernet (PoE) IEEE 802.3af.
Support MDI/MDI-X auto crossover function
Bandwidth control:64K/128K/256K/1M/2M/4M/8M bps and unlimited.
Built-in network interface (10Base-T/100Base-TX) for remote monitoring by
PC.
z
z
Smart Wizard settings for varied event and schedule recording conditions.
Built-in SD memory card slot for local storage and support SD High Capacity
(optional).
z
z
z
Built-in digital Motion Detection.
Built-in digital zoom function.
AGC, BLC, FL, ES, H-Mirror, IRIS Level and Day/Night function control
through web browser.
z
z
Two way audio.
Built-in IEEE 802.11b/g wireless module (EAN800AW).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
3. ACCESSING THE CAMERA MENU
Step 1.Start an Internet Explorer browser.
Step 2. Enter the IP address or host name of the camera in the Location/Address
field of your Internet Explorer browser. (Please refer to EAN800A/EAN800AW
Installation Guide for how to find the IP address)
Step 3. Input “Username” and “Password”. Default Username is “user1” and
default password is “11111111”.
Step 4. Click “Login” button.
Step 5. You might be required to download Active X, which is required to view
camera video. Please click "Yes".
Step 6. Congratulation!! You should be able to see the live image now.
13
14
1
2
3
4
5
6
7
8
9
10
11
12
7
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
button to display the "Live" page.
1. Press
Double click on the image to show a full screen display, double click again or press
ESC to return normal display.
2. Press
button to enter Setting page. In Setting page, there
are 8 sections: [System Info], [User Config], [Network], [Video], [Audio], [User],
[Event] and [System]. Please refer to “4. SETTING” for further information.
3. Press
button to close the network page.
4. Video Stream
Select Video Stream from Stream 1 / Stream 2, Stream 3 and Stream 4. Please refer to
“4.4.1 Multi Streaming” for further information.
5. View Size
You can select View size to either reduce or enlarge the image to the appropriate view
size.
Select the view size for live images from:
NTSC: 704*480/640*480/352*240/320*240/176*120
PAL: 704*576/640*480/352*288/320*240/176*144
6. Digital Zoom
Press “+” or “-“ button to enlarge / reduce the displayed image. (max. is X10)
7. Record
The record button is used to record the current video stream. The location where the
image file is saved can be specified in Setting -> User’s Config. Please refer to “4.2
User Config” for further information.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Note: Record segment is limited to 5 min. If you need to do long time recording,
please set schedule recording. For more details about schedule recording,
please see “4.7 Event”.
8. Snapshot
The
Snapshot button saves a snapshot of the video image currently being
displayed. The location where the snapshot data is saved can be specified in Setting ->
User’s Config. Please refer to “4.2 User Config” for further information.
9~10. Play Audio/Transmit Audio
Click the “Play Audio” and “Transmit Audio” buttons to switch the sound off and on
for the speaker and microphone, respectively.
11. Manual Control – Trigger Event
Press “Trigger Event” button to trigger an event directly from live view page, and
event actions will be effective if they have been set in “Event” menu. (Please refer to
“4.7.1 Event”)
12. Manual Control – Reset Alarm
Press “Reset Alarm” button to reset alarm output remotely.
13. Status Display
The name of the camera whose settings currently being configured, current date/time
and current frame rate will be displayed.
14. Event signals
Alarm
Motion
When an alarm or motion event is triggered, a signal icon will flash to alert user.
The first icon is for alarm event and rest of the 5 icons are for motion event. The
motion event icons which differed by colors correspond to the motion trigger areas
you have set in Motion menu. Please refer to “4.7.2 Motion” for detailed information
about Motion setup.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4. SETTING
Click this button to display the setup menu.
4.1 System Info
System information and system log check of the setup menu can be performed on this
page. The “System Info” page has 2 tabs: [Information] tab and the [Log] tab.
4.1.1 Information
System Information: Firmware version, MAC address, Video Type, Model number.
(unchangeable, for reference only)
10
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.1.2 Log
System Log:
Date/Time: displaying date and time of the log.
Log message: all information and event message, including login, user’s IP, reboot,
firmware upgrade, load factory default, configuration reset and event detected.
System will keep the newest 256 records.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
button to export system log into “.txt” file and select the
Press
location where the exported log file will be saved to.
4.2 User Config
Live view configuration is to be set by user. Each login user can make his/her own
settings for the following items:
Text Setting
Check the box for text of Machine name, Date/Time or Frame Rate to be
displayed on the screen.
Text Color
Foreground Color: Select the foreground color of text to be displayed by moving
the slide bar between Red, Green and Blue until your desire color is obtained.
Position: Select the position where the text will be displaying from Upper Left /
Lower Right / Lower Left.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Date/Time Format Used in Text
Select Date/Time Format from the following options:
Time Format: 24 Hours or 12 Hours.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Recording/Snapshot Export Setting
Enable Event Recording to PC: Allow event video recorded to users' PC if any
events have been set to record to PC.
Export folder: Select Export folder by clicking on
folder to be exported.
button, then direct to the
File size: Able to limit the size of the single recording file in minutes. When the
single recording file size exceeds the time you set, system will create a new file to
continue recording.
Overwrite: Select “ON” for overwriting recording/snapshot file when the disk
storage capacity is full.
If the remaining hard disk capacity is less than ____ MB (enter the value you wish
to set between 50~2000), system will stop recording or start overwriting.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Language Setting
Language: Select the language to be displayed in web page. Default language is
English. To add a new language which is not listed in the original configuration,
13
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
press the Browse button to locate the new language file (.evb) and then click the
Load button.
Note: Upload a new language file will reboot system automatically. Please
reconnect IP camera after reboot.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3 Network
The network settings and the settings relating to Network, DDNS, Bandwidth,
SMTP/FTP and Network Alarm can be configured on this page.
The "Network setup" page has 5 tabs of the [Network] tab, the [DDNS] tab, the
[SMTP/FTP] tab and the [Network Alarm] tab.
4.3.1 Network
The following information is required to configure the network settings. Contact
the network administrator or your Internet service provider.
• IP Type
14
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
• IP address
• Subnet mask
• Gateway (when using the gateway server/router)
• Primary DNS, Secondary DNS (when using DNS)
• HTTP Port
IP SETTING
IP Type
DHCP: Configure the DHCP server not to assign the same IP addresses used for
the other network cameras and PCs whose IP address is unique.
Refer to the network administrator for the settings of the server.
Default: DHCP.
Static IP: User can manually set the static IP for network connection.
PPPoE: This is a DSL connection application, ISP will ask user to input user name
and password.
Note: If PPPoE is used as IP type, IP Utility software will not be able to detect
the device.
IP address
When not using DHCP, enter the IP address of the camera. Do not enter the IP
address already used for PC or other network cameras.
Subnet Mask
This field is to set the netmask for your network so as the IP camera will be
recognized within the network. Example: 255.255.255.000. When DHCP is
selected, the DHCP server will assign this value automatically.
Gateway
This field is to set the gateway for your network so the IP camera will be
recognized within the network. When DHCP is selected, the DHCP server will
assign this value automatically.
Primary DNS
An IP address of DNS server that is provided by ISP.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Secondary DNS
If your ISP provides you an IP address secondary DNS, please set it here.
Username
Enter User name of the account (used only for PPPoE).
Password
Enter Password of the account (used only for PPPoE).
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Port Setting
HTTP Port
Port number for HTTP/WEB communication.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.3.2 DDNS
DDNS setting
When accessing the camera via the Internet from the network environment of
which the global IP address is obtained using DHCP, the DDNS function is
necessary.
To use the DDNS function, it is necessary to connect to the dedicated DDNS
server. We offer 4 DDNS server providers as follow:
Enable: Check the box to enable DDNS setting.
Service ISP: If you choose EverFocus DDNS server, you can obtain a free account
Enter an IP Cam Account Name:
.everfocusddns.com
Press button to register or update DDNS account.
If you wish to get a domain name from other DDNS provider, it is necessary to
17
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
configure Record ID, FQDN, Username and password and register in DDNS
server. Refer to the web site for further information about the DDNS.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.3.3 Bandwidth
Bandwidth Setting
Max. Bandwidth: Specify, Unlimited / 64 K/ 128 K/ 256 K / 512 K / 1M / 2M / 4M
/ 8M bps. the maximum bandwidth that the camera is allowed to use on the
network. This is a useful function when connecting the camera to busy or heavily
loaded networks. The default setting is Unlimited.
Max. Client Limit: enter a value here to restrict the number of clients accessing the
camera. This is useful if you need to save on bandwidth. Up to 32 clients is
allowed to see live video simultaneously. Subsequent viewers will see a blank
image.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.3.4 SMTP/FTP
Set SMTP
The settings relating to the mail server used to send the e-mail notification from the
camera to predefined addresses via SMTP can be configured.
SMTP Server: Enter the IP address or the host name of the SMTP server used to
send e-mails.
SMTP Port: Enter the port number for SMTP. Default is 25.
Authentication: Check the box, if the SMTP server requires Authentication (user/
password).
User name: Input the login user ID if the SMTP server requires Authentication.
Password: Input the password if the SMTP server requires authentication.
Receiver Address: Input the e-mail address for receiving e-mail message when the
EVENT is enabled and triggered. Please use “;” to separate address.
Sender Address: Input sender’s e-mail address, so that receiver can recognize the
sender when an event message is sent out.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Send Test Mail: Press
address.
button to send a testing mail to the assigned
Set FTP
The settings relating to the FTP server used to transmit the alarm images can be
configured.
FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for FTP server. Default is 21.
Recording Path: Assign the recording path.
User Name: Set FTP User’s name.
Password: Set FTP password.
PASV mode: Check to enable Passive mode, normally enable Passive mode. When
failed to establish the connection, uncheck "PASV" mode.
Test FTP Server: Press
FTP server.
button to send a testing file to the assigned
Press Apply to apply the setting changes or Reset to reset without saving the
change.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.3.5 Network Alarm (reserved for PowerCon)
Set Network Alarm
This function is reserved for PowerCon software, for the detail setting please refer
to PowerCon network alarm protocol.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.3.6 Wireless (EAN800AW)
Wireless Setting
Enable: Check the box to enable wireless connection.
SSID: Name of the wireless network the camera. The field accepts up to 32
alphanumeric characters. The name must be exactly the same as the used in the
wireless access point or the connection will not be established.
Network Type: Infrastructure or Ad-Hoc. Default is Infrastructure.
“Infrastructure” Make the Network Camera connect to the WLAN via an Access
Point.
“Ad-Hoc” Make the Network Camera connect directly to a host equipped with a
wireless adapter in a peer-to-peer environment.
Channel: Shows the wireless channel currently in use. Default is 1.
Security: WPA or WEP. Default is WPA.
Authentication: Open or Shared. Default is Open.
“Open” – communicates the key across the network.
“Shared” – allows communication only with other devices with identical WEP
settings.
Key Length: 64 or 128 bits. Default is 64 bits.
Key Format: Hexadecimal or ASCII. Default is HEX.
Network Key: Entering a key in either hexadecimal or ASCII format.
Confirm Key: Double confirm network key.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
WPA (Wi-Fi Protected Access) key should follow either one of the following rules:
- As 64 hexadecimal (0-9, A-F) characters.
- As 8 to 63 ASCII characters.
WEP (Wired Equivalent Protection) key should follow either one of the following
rules:
- As 5 characters for 64-bit WEP and 13 characters for 128-bit WEP.
- As 10 hexadecimal (0-9, A-F) characters for 64-bit WEP and 26 hexadecimal
(0-9, A-F) characters for 128-bit WEP.
IP Status: Show IP status when wireless connection, including IP Type, IP Address,
Subnet mask, Gateway, Primary DNS, Secondary DNS.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.4 Video
The settings relating video such as streaming, camera OSD can be configured on
this page.
The "Video" page has 2 tabs: the [Multi-streaming] tab and the [Camera] tab.
4.4.1 Multi Streaming
23
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Stream Setting
The system can output 4 video streams simultaneously. For each of them, user can
set compression format, resolution, quality and frame rate individually. Stream 1 is
always enabled for live view.
Check “Enable” box to enable other streams.
Format: Select encode format from H.264, MPEG4 and MJPEG.
Resolution:
NTSC: 4CIF (704*480) / VGA (640*480) / CIF (352*240) / QVGA (320*240) /
QCIF (176*120)
PAL: 4CIF (704*576) / VGA (640*480) / CIF (352*288) / QVGA (320*240) /
QCIF (176*144)
Quality: there are 8 types of quality, please choose from Highest / Higher / High /
Middle / Normal / Low / Lower / Lowest.
Frame Rate: select from NTSC: 1 / 3 / 5 / 15 / 30 fps, PAL: 1/ 2.5/5/12.5/25 fps
Note: Total frame rate cannot exceed 60 fps.
System performance may be influenced if user enables 4 video streams
simultaneously.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Video Recording Setting
User can set video recording by selecting one of the enabled video streamings.
This will allow user to view live images as well as to record video of the other
video streaming.
Video Stream: Select video recording stream from any enabled stream.
Video File format: Recording file will be saved as AVI or ARV, select which file
format to be used.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.4.2 Camera
Image setting
Hue: to increase or decrease hue of video images. It is adjustable from 0~255.
Contrast: to increase or decrease object contrast of images. It is adjustable from
0~255.
Saturation: to increase or decrease color saturation of video images. It is
adjustable from 0~255.
Brightness: to increase or decrease object contrast of images. It is adjustable
Brightness from 0~255.
Lens Setting
LENS: Select DC or Fixed of the lens type used for camera.
DC: DC driven Lens
Fixed: Manual Lens
IRIS setting: to manually adjust IRIS level of Lens when selecting DC driven
Lens. It's adjustable from 0~31.
Camera Setting
AGC: Select ON or OFF for Auto Gain Control.
ON: when illuminance becomes darker, gain will automatically be incremented
and screen will become brighter.
OFF: Gain will not be incremented.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
BLC: Select ON or OFF for Backlight Compensation.
ON: When the background of the subject is very bright and the subject
itself is dark, set the BLC ON. The BLC will measure the light of the
image center and the lens iris will automatically set for optimum image
quality.
OFF: Backlight will not be compensated.
FL: Select ON or OFF for Flickerless.
ON: When picture flicker fiercely, turn FL on, then the camera will stabilize the
speed of electronic shutter automatically, and reduce the flicker immediately.
OFF: Disable Flickerless function.
ES: Select ON or OFF for Electronic Shutter.
ON: the auto control of the shutter speed can be performed according to the
brightness of the screen.
OFF: Disable electronic shutter.
H-Mirror: Select ON or OFF for Horizontal Mirror.
ON: Enable a horizontal image inversion.
OFF: Disable the inversion.
D/N: Select ON or OFF for Day/Night function.
ON: Enabling the image to turn from color to B/W when the illumination is about
5 Lux
OFF: Disable D/N function.
Note:
1. If ES is on, FL takes no effect. ES>FL
2. If AGC is off, BLC has no effect., BLC works when AGC is on. AGC > BLC
3. AGC must be on to Day/Night auto switch function work.
4. If ES is on, IRIS level adjustment takes no effect, ES> IRIS level
5. If using DC driven Lens, BLC and ES should be off.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.5 Audio
The EAN800A/EAN800AW camera can transmit audio to other clients using a
built-in microphone or connecting to external microphone to play audio received from
other clients via connected speakers. This section describes how to configure the basic
audio settings.
Audio
Check Enable Audio box to enable audio function.
Audio Input: Audio from an internal microphone or a line source can be connected
to the Audio connector of EAN800A/EAN800AW. The audio source can be
selected from Internal Microphone, External Audio Input L and External Audio
Input R.
Note:
Microphone is not available for U.S. region.
Audio Input volume: Adjust the Audio Input Volume for the audio input devices
connected to the camera if there are problems with the sound input being too low
or high.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.6 USER
User Information
Maximum 10 users can be set for using the IP camera. The user information
displays the authorized users and access levels:
• Supervisor/Administrator –a supervisor/administrator has unrestricted access to
the Setting menu and can determine the registration of all other users. However,
administrator is not allowed to change supervisor’s account and password.
• User- a user can view the Live View page, system info, network, video, audio,
and adjust user config settings. The user does not have access to the “user”,
“event” and “system pages”.
• Guest- the lowest level of access, which only allows the user access to the Live
View page.
Note: Please select Active in Status section to activate user account.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.7 EVENT
An event in the camera is when an Event Type is activated and causes certain actions
to be performed. The event type is the set of conditions that specifies how and when
which actions will be performed.
This table describes how to setup action types and event type.
Event Type
Action Type
Manual
Trigger
Motion
Detection
Schedule
Recording
Alarm Input
Pre/Post-Alarm
Trigger Alarm
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
x
Send Mail notification
Upload to FTP**
Record to SD Card
Record to PC*
x
x
x
x
x
Network Alarm
Re-trigger
Note: 1. * Record to PC only works when PC and IP camera are connected.
2. **Either Upload to FTP or Record to Network Storage can be selected to
record event video to remote site.
3. Up to 10 event types can be configured in the camera, and up to 3 of these
can be configured to upload images.
4.7.1 Event
The settings relating to event occurrences such as settings for the event
occurrence, motion, alarm and time mask can be configured on this page.
The "Event " page has 4 tabs: [Event] tab, the [Motion] tab, the [Alarm] tab and
the [Time Mask] tab.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Press
button to add an event condition.
To modify the event list, click on the event and it will be highlighted. Press
button to modify the setting.
To remove an event from event list, click on the event and it will be highlighted.
Press
button to remove the event.
Check Enable checkbox to activate event actions when the event occurs in the
specified time zone.
To change the priority of events, click on the event and it will be highlighted. Press
or
button to move between events. The event that has
highest priority will be activated first.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
This example describes how to set the camera to upload images to FTP when
someone press Manual trigger button:
1. Click
button in Event page.
2. Enter an event name for the event, e.g. Event 1
3. Select “Manual Trigger” as event type.
4. Select “Upload to FTP” as action type.
5. Check “Enable Pre-alarm Buffer” and “Enable Post-alarm Buffer”. For pre-and
post alarm buffer setting, please refer to “4.7.3 Alarm”.
6. Check “Enable This Event”.
7. Select “Always” for time mask. For detail about Time Mask, please refer to
“4.7.4 Time Mask”.
8. Click
to save this event in event list.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.7.2 Motion
Motion Detection
User can define the motion area to be detected by left clicking the mouse to draw
lines. Every click is an end point of the line. When the detection area is formed,
double click the mouse to have all the lines connected. To remove the selection,
simply right click the mouse, the selected polygon will be deleted.
Press
Press
to update the current image.
to have the entire screen selected for motion detection.
Press
Press
to clear all selections.
and click on the polygon, to erase that polygon.
There are 5 motion trigger areas, which can be distinguished by 5 different colors.
Check Enable checkbox to enable event action.
For each of them, you can set the event action to be activated. Event action can be
set in “Event” section.
Moreover, you can set the Sensitivity level for motion triggered by selecting from
1 (low), 2, 3, 4, 5, 6, 7, 8, 9 to 10 (high).
32
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
4.7.3 Alarm
Alarm Output Setting
Contact Type: Normal Close, Normal Open
Duration Time: Select duration time of alarm output from 5 sec, 10 sec, 20 sec, 30
sec, 60 sec, 2 min, 3 min and 5 min.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Pre/Post Alarm Setting
This function is used to check what happened immediately before and after a
trigger, e.g. 5 seconds before or after a motion has been detected.
Pre-Alarm Buffer: Image saved internally in the server from the time immediately
preceding the trigger. Input the desired length of pre-trigger buffer time. It can be
set up to 120 seconds.
Post-Alarm Buffer: Image saved internally in the server from the time immediately
after the trigger. Input the desired length of post-trigger buffer time. It can be set
up to 120 seconds.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Re-trigger Filter Setting
Re-trigger Filter: Set a re-trigger filter time, if another event is triggered during
this time, this triggered event will be ignored.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.7.4 Time Mask
Time Mask Setting
Time mask setting allows you to schedule event actions.
Select Always for event action to be taken continuously.
Press
button to add new time period.
Mask name: Input a mask name for the new time period.
Check the check box for the day to be scheduled: Sun, Mon, Tue, Wed, Thu, Fri &
Sat.
Set the Start time and End time for time mask by clicking Up arrow or Down
arrow. Or simply press
for a full day of event action.
Press
button to remove a scheduled time period.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
An example on how to set weekend as time mask is as follows:
1. Click from time mask setting.
2. Enter Mask name, e.g. Weekend.
3. Check “Sun” & “Sat” boxes.
4. Select “Start time” and “End time” or “Full day”.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.8 SYSTEM
Date/Time, Daylight Saving, SD card and Maintenance settings can be performed
on this page.
The "System" page has 4 tabs of the [Date/Time] tab, the [Daylight Saving] tab,
the [SD card] tab and the [Maintenance] tab.
4.8.1 Date/Time
35
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Machine Name Setting
Machine Name: Enter the name of the camera. The entered name will be displayed
in the status display area.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Set Time Zone
Time Zone: Select a time zone according to the location where the camera is in
use.
Set Date/Time Manually
Date: Click the calendar and pick the date. Press << to go previous year, < to go
previous month, > to go next month and >> to go next year.
Time: Click on Hour, Minute, Seconds, am/pm; then use up arrow to increase
value and down arrow to decrease value.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
Set Date/Time Sync.
Check Enable NTP checkbox to enable NTP server.
NTP server: Time automatically adjusted by synchronizing with NTP server will be
used as the standard time of the camera.
Sync. Internal: Select an interval (1 - 24 hours: in 1 hour intervals) of
synchronization with the NTP server.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.8.2 Daylight Saving
Set Daylight Saving
Check Enable Daylight Saving checkbox to enable daylight saving.
Set the start time to daylight saving time.
Set the start week of daylight saving time: 1st / 2nd / 3rd / 4th / Last
Set the start date of daylight saving time: Sunday / Monday / Tuesday / Wednesday
/ Thursday / Friday / Saturday
Set the start month of daylight saving time: January / February / March / April /
May / June / July / August / September / October / November / December.
Set the starting time change of daylight saving time: Choose the “From” time and
“End” time when daylight saving starts.
Set the end time of daylight saving time.
Set the end week of daylight saving time: 1st / 2nd / 3rd / 4th / Last
Set the end date of daylight saving time: Sunday / Monday / Tuesday / Wednesday
/ Thursday / Friday / Saturday
37
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Set the end month of daylight saving time: January / February / March / April /
May / June / July / August / September / October / November / December.
Set the ending time change of daylight saving time: Choose the “From” time and
“End” time when daylight saving ends.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
4.8.3 SD Card
Setup SD Card
Notification: Notification will be made via e-mail when the remaining space of the
SD memory card reached the value selected from the following.
50%, 20%, 10%, 5%, 2%, 0%
Notes:
1. When "50%" is selected, e-mail notification will be made each time the
remaining space reaches 50%, 20%, 10%, 5%, 2% and 0%.
2. E-mail notification may not always be made at a very moment when the
remaining space of the SD memory card reached the selected value.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Event Recording:
FTP backup only: Event video will record to SD card when network is
disconnected.
Normal: Follow the event actions settings you have made in “Event” menu to
record event video to SD card.
Overwrite: Select ON for overwriting data when SD card memory is full. Select
OFF for not overwriting SD card data.
Press Apply to apply the setting changes or Reset to reset without saving the
change.
SD Card Utility
The total size and available size of the SD memory card will be displayed.
Depending on the state of the SD memory card, the size indications will differ as
follows.
Indication Description
Capacity ___ MB, available ___MB, used ___ %
Before formatting the SD memory card, it is necessary to press
button.
Once
button is pressed,
button will be shown for user to
insert the SD card back.
Press
button to format SD card.
Obtain images on the SD memory card
1. Access the camera using the Windows command prompt or FTP client software.
→ The window with the user name and password entry fields will be displayed.
2. Enter the user name whose access level is "1. Administrator" and its password.
→ Log in the camera.
3. A directory of all saved data will be displayed. You are now ready to obtain
images from SD card.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Note:
1. It is impossible to access the SD memory card in the process of formatting.
2. All data saved on the SD memory card will be deleted when the SD memory
card is formatted.
3. Do not turn the power of the camera off in the process of formatting.
4.8.4 Maintenance
Maintenance Server
Reboot: The unit is rebooted without changing any of the settings. Use this method
by pressing Reboot button if the unit is not behaving as expected.
Restore: The unit is restarted and most current settings are reset to the factory
default values by pressing Restore button. The only settings saved are:
•
•
IP setting
DDNS setting
Default: The Default button should be used with caution. Pressing this button will
return all of the camera's settings, including the IP address, to the factory default
values. The camera will then have to be re-installed.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Save/Load Configuration Server
To take a backup of all of the configurations, press Save to save all configurations
to a config. file. If necessary, it is then possible to return to the previous settings if
the settings are changed and there is unexpected behavior.
Press the Browse button to locate the saved config. file (see above) and then click
the Load button. The settings will be restored to the previous configuration.
Upgrade Firmware
Upgrade the EAN800A/EAN800AW with the latest firmware.
Press Browse button to search firmware file. Press Upgrade button to upgrade the
firmware.
Note 1: Do not disconnect power to the unit during the upgrade. The unit reboots
automatically after the upgrade has completed. (1-5 minutes.)
2. During upgrading process, all event recording actions will be stopped. It
will continue to record after the camera is rebooted.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
5. SPECIFICATIONS
CAMERA
Pickup Device
1/3" Sony Super HAD Interlaced CCD
NTSC: 768 (H) x 494 (V); PAL: 752 (H) x 582 (V)
Pixel Effective
Sensitivity
0.4 Lux / F=1.2
Yes
Day & Night
Lens
Optional C/CS mount, manual / DD control supported
Video Output
Video Output Resolution
BNC socket, composite 1 V p-p / 75Ω
520 TVL
VIDEO STREAMING
Video Compression
Video Resolution
Video Quality
H.264/MPEG-4/M-JPEG
D1, VGA, CIF, QVGA, QCIF
8 levels adjustable
Frame Rate
Up to 30fps
AUDIO
Microphone
Audio Input
Built-in omni-directional microphone (not available for U.S. region)
3.5 mm stereo socket, sensitivity 1 Vrms
Audio Output
Compression Method
Operation Mode
3.5 mm stereo socket, sensitivity 1 Vrms at load of 10KOhm and 50pf.
IMAADPCM (Pulse Code Modulation)
2 way audio
NETWORK
Interface
10Base-T/100Base-TX auto-negotiation, RJ-45 socket
Support MDI/MDI-X auto crossover function
Supported Protocols
Bandwidth Control
Max. Client Limit
HTTP, TCP / IP, UDP, RTP, RTSP, FTP, SMTP, DHCP, DNS, DDNS, NTP
Min. 64 kbps adjustable
32 simultaneous clients
ALARM
Alarm Input
Alarm Output
1 x input for dry contacts, Normal Open / Normal Closed adjustable
1 x dry relay contact, Normal Open / Normal Closed adjustable,
70 VDC / 200 mA max
SERIAL INTERFACE
RS-485
RS-485 interface bi-direction half-duplex (functionality reserved)
EVENT MANAGEMENT
Event Triggered By
Notification Over
Alarm input, Manual trigger, Motion detection and Schedule recording
Trigger alarm output, Send mail notification, Upload video to FTP, Record video
to SD card, Record video to PC and Network alarm
Pre- and Post- alarm Buffer
48MB RAM reserved for pre-alarm record up to 120 sec.
LOCAL STORAGE
SD Card (Optional)
Secure Disk physical layer specification version 2.0
Supports SDHC Host Specification
POWER
42
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
Power Supply
12 VDC & PoE
Power cord with 5.5 mm cable socket, 5.5 mm adapter cable 20 cm included in
package
Power Over Ethernet
Power Consumption
Yes (PoE 802.3af)
5W max. (12VDC)
PHYSICAL
Weight
500 g ; 1.102 LBS
Dimensions
68 (W) x 57 (H) x 136 (D) mm / 2.7" (W) x 2.2" (H) x 5.4" (D)
With BNC socket: 68 (W) x 57 (H) x 146 (D) mm / 2.7" (W) x 2.2" (H) x 5.7" (D)
With Antenna: 68 (W) x 125 (H) x 167 (D) mm / 2.7" (W) x 4.9" (H) x 6.6" (D)
ENVIRONMENTAL
Operating Temp.
Humidity
0°C ~ 40°C ; 32°F ~ 104°F
< 90% not condensing
43
Download from Www.Somanuals.com. All Manuals Search And Download.
EAN800A/EAN800AW
EverFocus Electronics Corp.
Head Office:
China Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chi, Taipei, Taiwan
TEL: 886-2-26982334
FAX: 886-2-26982380
Room B-05D-1, KESHI PLAZA, Shangdi
Information Industry Base,Haidian
District, Beijing China
100085
TEL: +86-10-62973336/37/38/39
FAX: +86-10-62971423
USA Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844-8888
FAX: +1-626-844-8838
Europe Office:
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: 49-2822-9394-0
FAX: 49-2822-939495
USA N.Y. Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
Tel: 631-436-5070
Japan Office:
1809 WBG Maribu East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: 81-43-212-8188
FAX: 81-43-297-0081
FAX: 631-436-5027
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household waste.
Please, dispose of this equipment at
your local community waste
®
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
EverFocus
Download from Www.Somanuals.com. All Manuals Search And Download.
|