High Resolution B/W Weatherproof Camera
User’s Manual
and
Operation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Safety Warning …………………………………………1
Introduction……………………………………………..2
Specification…………………………………………….3
Major Parts Names…..…………………………….…..4
Installation Instructions………………………….….…5
Settings………………………………………………….7
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Warning
1. Handle the camera with care.
Be careful when handling the camera, do not drop it or subject
it to strong shock or vibration to prevent any damages to it. Do
not disassemble it or place it on an unstable base.
2. Do not install the camera near electric or magnetic fields.
Installed the camera away from TV, radio transmitter, magnet,
electric motor, transformer, audio speakers because the
magnetic fields generate from above devices will distort the
video image.
3. Do not install the camera in the high temperature environment.
Installed the camera away from stoves, or other heat
generating devices as the high temperature could cause
deformation, discoloration or other damages of the camera.
Install the camera at where the temperature range will stay
between -35℃~+50℃ for 12VDC,-45℃~+50℃ for 24VAC.
4. Never face the camera toward the sun.
Never aim the camera at the sun or other extremely bright objects
whether it is in use or not.
5. Cleaning
Do not touch the surface of CCD sensor by hand directly. Use
a soft cloth to remove the dirt from the camera body. Use lens
tissue or a cotton tipped applicator and ethanol to clean the
CCD sensor and the camera lens. When the camera is not in
use, put the cover cap on the lens mount.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
The EZ180 series offers great performance in 1/3”image format B/W
CCD camera. The EZ180 is ideal for outdoor applications such as
parking lots, gas stations or shopping malls. The sophisticated circuit
design provides a heater that turns on at 10℃ for cold weather. The
EZ180 will provide protection against the elements and provide an
excellent quality picture.
Main Features :
„ High Resolution: 560 TV Lines.
„ Two types of built-in vari-focal lens for versatile applications.
„ Designed with sturdy aluminum shell specifically for outdoor
surveillance.
„ Removable sun shield.
„ The heater allows the camera to be used in extremely low
temperature to -46°C.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Specification
EZ180
Pickup Device
1/3” SONY B/W CCD
Picture Elements
768 x 494 (EIA)
752 x 582 (CCIR)
Horizontal Resolution
Video Output
560 TV lines
BNC 1.0Vp-p, 75 ohm
Lens Focal Length
Vari-focal lens f=3.5~8mm
Vari-focal lens f=9~22mm
*Lens models and availability vary in different regions
Sensitivity
0.1 lux/F=1.6
Gamma Correction
S/N Ratio
0.45
Over 48dB (AGC off)
Back Light Comp.
Auto Gain Control
Flickerless
On/Off switch
On/Off switch
On/Off switch
Line Lock
On/Off switch
Sync. Mode
Internal Sync.
Weatherproof
Power Source
Power Consumption
IP66
12VDC/24VAC
12VDC: 7.5W max. (Heater ON)
24VAC: 10W max. (Heater ON)
Dimensions
With sun shield : 90.7mm(W) x 70mm(H) x 172mm(L);3.57"(W) x
2.8"(H) x 6.8"(L)Without sun shield: 57mm(O.D) x 132mm(L);
2.2"(O.D) x5.2"(L)
Weight
0.71 kg ; 1.6 lbs
0.91 kg ; 2 lbs (with bracket)
-46℃ ~ 50℃ ; -50.8°F~122°F (20%~80% Humidity)
Operating Temperature
Heater Operating Temperature 10 °C ; 50°F
Certifications FCC/CE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Major Parts Names and Their Functions
Back Fixing Plate
Swivel
Screw
Mounting
Base
Set-Screw
Sun Shield
Cover
Assembly
Screw
Fixing Screw
Front
Fixing Plate
IRIS ALC/Level Adjustment
O-ring Seal
Focus Zoom
Lens
Heater
Mounting Bracket
Control Switch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
1. Using the supplied screws, mount the bracket base on the desired
location.
2. Connect the BNC connector of the camera to a monitor or other
video device through a 75 ohm type coaxial cable with BNC female
connector at cable extension.
3. Connect the 24VAC or 12VDC regulated power source of the camera
(power jack) to the power-in jack with 2mm plug. For 12VDC
power source, please make sure the power plug is center+ outer-
for heater normal operation.
4. Our factory settings is for you to get the best image within about 3~5
meters (for veri-focal lens f=3.5~8mm) or 5~10 meters (for
veri-focal lens f=9~22mm) . If it is out of focus, or any other
adjustment is required, follow the procedures below.
a. Remove the fixing screw in the front, which hold the sun shield
cover. Remove the sun shield cover.
b. Twist open and carefully remove the housing cover.
(Please pay attention to prevent damage to the “O”-Ring seal.)
c. Loosen the focal lens and focus locking screws.
d. Adjust the lens to bring the subject into focus.
(Caution: Heater elements could be hot! When camera power is
on, use caution when adjusting the camera.)
e. Retighten the screws.
f. Please refer to the Settings section for the details of the other
adjustments. Adjust accordingly if necessary.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
g. When all the adjustments and settings are completed, overlaying
the cover gently. Be careful not to damage to the “O”-Ring and
camera components.
h. To reassemble the sun shield, match the hole on the sun shield to
the back fixing plate of camera, Fix the screw on the front fixing
plate. Make sure the wider side of the fixing plate holds the edge
of the camera well.
5. Attach the camera onto the mounting bracket.
6. Loosen the swivel screw and point the camera to the desired
direction.
7. Tighten the swivel screw. To strengthen the fixing power of the
swivel screw, tighten the set-screw with the set-screw wrench.
(supplied)
Notes:
(A) Make wiring connections only after it has been determined that
power has been disconnected.
(B) There is a desiccant pack attached to the housing base under the
camera which is designed to absorb any moisture trapped inside
the housing during adjustment. To avoid excessive moisture
build up, it is recommended that the camera not be installed in
rainy or excessively damp conditions. It is also advisable to
limit the number of times the housing cover is removed. The
desiccant pack can be replaced if condensation develops inside
the housing.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings
The camera is set up at factory and normally requires no adjustments.
Sometimes, however, adjustments may be necessary. Please refer to the
following description for the function details.
„ The IRIS ALC and IRIS Level adjustments are located on the side
circuit board, use a screwdriver to adjust if it’s necessary.
IRIS Level
Adjustment
IRIS ALC
Adjustment
Control Switches
IRIS Level Adjustment
To adjust brightness level –
z Turn the IRIS Level Adjustment VR counterclockwise to get
darker picture.
z Turn the IRIS level adjustment VR clockwise to get brighter
picture.
IRIS ALC Adjustment
To select light metering method –
z Turn the IRIS ALC Adjustment VR counterclockwise for
Average Metering.
z Turn the IRIS ALC Adjustment VR clockwise for Peak
Metering.
Download from Www.Somanuals.com. All Manuals Search And Download.
7
„ The 4 control switches are also located on the side circuit board, the
switches in orders are for Flickerless, Back Light Comp, Auto Gain
Control and Line Lock.
Normal
FL
On
On
On
On
Normal
Off
BLC
AGC
Off
LL
Control Switches
FL(Flickerless) Normal/On
When picture flicker fiercely, turn FL on, then the camera will stabilize
the speed of electronic shutter at 1/100(NTSC) or 1/120(PAL)
automatically, and reduce the flicker immediately. The default setting is
Normal.
BLC (Back Light Compensation) Normal/On
When BLC is turned on, the AGC, ES and IRIS operating point is
determined by averaging over the center area instead of entire
field-of-view, so that a dimly-lit foreground object at center area can be
clearly distinguished from brightly-lit backgrounds.
BLC should not be used unless it is needed to compensate for back-lit.
The default setting is Normal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
AGC (Automatic Gain Control) Off/On
AGC ON: The sensitivity increases automatically when light is low.
AGC OFF: A-low-noise picture is obtained under a low light condition.
The default setting is On.
LL (Line-Lock) Off/On
To select the sync mode between Internal Sync.(LL off) and Line-Lock
(LL on).
Set the line-lock off, the camera will synchronize to the internal time
base. Set the line-lock on, the camera’s vertical synchronization can be
driven by the AC signal in the power lines.
The default setting is Off
Note: Line-Lock sync mode operation is possible only when used with
an AC power source; it’s not possible with a DC power source.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Head Office:
Europe Office:
12F, No.79 Sec. 1 Shin-Tai Wu Road,
Hsi-Chih, Taipei, Taiwan
TEL: +886-2-26982334
FAX: +886-2-26982380
Albert-Einstein-Strasse 1
D-46446 Emmerich, Germany
TEL: +49-2822-9394-0
FAX: +49-2822-939495
USA L.A. Office:
China Office:
1801 Highland Ave. Unit A
Duarte, CA 91010, U.S.A.
TEL: +1-626-844-8888
FAX: +1-626-844-8838
Room B-05D-1, KESHI PLAZA, Shangdi
Information Industry Base, Haidian District,
Beijing, China 100085
TEL: +86-10-62973336/37/38/39
FAX: +86-10-62971423
USA N.Y. Office:
Japan Office:
415 Oser Avenue Unit S
Hauppauge, NY 11788
TEL: +1-631-436-5070
FAX: +1-631-436-5027
1809 WBG MARIBU East 18F,
2-6 Nakase.Mihama-ku.
Chiba city 261-7118, Japan
TEL: +81-43-212-8188
FAX: +81-43-297-0081
Your EverFocus product is designed and
manufactured with high quality materials and
components which can be recycled and
reused.
Ihr EverFocus Produkt wurde entwickelt und
hergestellt mit qualitativ hochwertigen
Materialien und Komponenten, die recycelt
und wieder verwendet werden können.
Dieses Symbol bedeutet, dass elektrische und
elektronische Geräte am Ende ihrer
Nutzungsdauer vom Hausmüll getrennt
entsorgt werden sollen.
This symbol means that electrical and
electronic equipment, at their end-of-life,
should be disposed of separately from your
household waste.
Please, dispose of this equipment at your
local community waste collection/recycling
centre.
Bitte entsorgen Sie dieses Gerät bei Ihrer
In the European Union there are separate
collection systems for used electrical and
electronic product.
örtlichen kommunalen Sammelstelle oder im
Please, help us to conserve the environment
we live in!
P/N: MEZ1G0040B VerC
Download from Www.Somanuals.com. All Manuals Search And Download.
|