ELECTRIC RANGE
Use & Care Guide
For questions about features, operation/performance,
parts, accessories or service, call: 1-800-253-1301.
or visit our website at...
Table of Contents................................................. 2
To the installer: Please leave this
instruction book with the unit.
To the consumer: Please read and
keep this book for future reference.
W10017730
Download from Www.Somanuals.com. All Manuals Search And Download.
RANGE SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
DANGER
You can be killed or seriously injured if you don't
instructions.
follow
WARNING
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
The Anti-Tip Bracket
The range will not tip during normal use. However, the range can tip if you apply too much force or weight to the open door without
having the anti-tip bracket fastened down properly.
WARNING
Tip Over Hazard
A child or adult can tip the range and be killed.
Connect anti-tip bracket to rear range foot.
Reconnect the anti-tip bracket, if the range is moved.
See the installation instructions for details.
Failure to follow these instructions can result in death or serious burns to children and adults.
Anti-Tip Bracket
Making sure the anti-tip bracket is installed:
• Slide range forward.
• Look for the anti-tip bracket securely attached to floor.
• Slide range back so rear range foot is under anti-tip bracket.
Range Foot
The California Safe Drinking Water and Toxic Enforcement Act requires the Governor of California to publish a list of substances
known to the State of California to cause cancer, birth defects, or other reproductive harm, and requires businesses to warn of
potential exposure to such substances.
WARNING: This product contains a chemical known to the State of California to cause cancer, birth defects, or other
reproductive harm.
This appliance can cause low-level exposure to some of the substances listed, including benzene, formaldehyde, carbon
monoxide, and toluene.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: To reduce the risk of fire, electrical shock,
ꢀ Protective Liners – Do not use aluminum foil to line surface
unit drip bowls or oven bottoms, except as suggested in
the manual. Improper installation of these liners may result
in a risk of electric shock, or fire.
injury to persons, or damage when using the range, follow
basic precautions, including the following:
ꢀ WARNING: TO REDUCE THE RISK OF TIPPING OF
THE RANGE, THE RANGE MUST BE SECURED BY
PROPERLY INSTALLED ANTI-TIP DEVICES. TO CHECK
IF THE DEVICES ARE INSTALLED PROPERLY, SLIDE
RANGE FORWARD, LOOK FOR ANTI-TIP BRACKET
SECURELY ATTACHED TO FLOOR, AND SLIDE RANGE
BACK SO REAR RANGE FOOT IS UNDER ANTI-TIP
BRACKET.
ꢀ Glazed Cooking Utensils – Only certain types of glass,
glass/ceramic, ceramic, earthenware, or other glazed
utensils are suitable for range-top service without breaking
due to the sudden change in temperature.
ꢀ Utensil Handles Should Be Turned Inward and Not Extend
Over Adjacent Surface Units – To reduce the risk of burns,
ignition of flammable materials, and spillage due to
unintentional contact with the utensil, the handle of a
utensil should be positioned so that it is turned inward, and
does not extend over adjacent surface units.
ꢀ CAUTION: Do not store items of interest to children in
cabinets above a range or on the backguard of a range –
children climbing on the range to reach items could be
seriously injured.
ꢀ Do Not Soak Removable Heating Elements – Heating
ꢀ Proper Installation – Be sure the range is properly installed
elements should never be immersed in water.
and grounded by a qualified technician.
ꢀ Do Not Cook on Broken Cooktop – If cooktop should
break, cleaning solutions and spillovers may penetrate the
broken cooktop and create a risk of electric shock. Contact
a qualified technician immediately.
ꢀ Never Use the Range for Warming or Heating the Room.
ꢀ Do Not Leave Children Alone – Children should not be left
alone or unattended in area where the range is in use.
They should never be allowed to sit or stand on any part of
the range.
ꢀ Clean Cooktop With Caution – If a wet sponge or cloth is
used to wipe spills on a hot cooking area, be careful to
avoid steam burn. Some cleaners can produce noxious
fumes if applied to a hot surface.
ꢀ Wear Proper Apparel – Loose-fitting or hanging garments
should never be worn while using the range.
ꢀ Use Care When Opening Door – Let hot air or steam
escape before removing or replacing food.
ꢀ User Servicing – Do not repair or replace any part of the
range unless specifically recommended in the manual. All
other servicing should be referred to a qualified technician.
ꢀ Do Not Heat Unopened Food Containers – Build-up of
pressure may cause container to burst and result in injury.
ꢀ Storage in or on the Range – Flammable materials should
not be stored in an oven or near surface units.
ꢀ Keep Oven Vent Ducts Unobstructed.
ꢀ Do Not Use Water on Grease Fires – Smother fire or flame
or use dry chemical or foam-type extinguisher.
ꢀ Placement of Oven Racks – Always place oven racks in
desired location while oven is cool. If rack must be moved
while oven is hot, do not let potholder contact hot heating
element in oven.
ꢀ Use Only Dry Potholders – Moist or damp potholders on
hot surfaces may result in burns from steam. Do not let
potholder touch hot heating elements. Do not use a towel
or other bulky cloth.
ꢀ DO NOT TOUCH HEATING ELEMENTS OR INTERIOR
SURFACES OF OVEN – Heating elements may be hot even
though they are dark in color. Interior surfaces of an oven
become hot enough to cause burns. During and after use,
do not touch, or let clothing or other flammable materials
contact heating elements or interior surfaces of oven until
they have had sufficient time to cool. Other surfaces of the
appliance may become hot enough to cause burns – among
these surfaces are oven vent openings and surfaces near
these openings, oven doors, and windows of oven doors.
ꢀ DO NOT TOUCH SURFACE UNITS OR AREAS NEAR
UNITS – Surface units may be hot even though they are
dark in color. Areas near surface units may become hot
enough to cause burns. During and after use, do not touch,
or let clothing or other flammable materials contact surface
units or areas near units until they have had sufficient time
to cool. Among those areas are the cooktop and surfaces
facing the cooktop.
For self-cleaning ranges –
ꢀ Use Proper Pan Size – The range is equipped with one or
more surface units of different size. Select utensils having
flat bottoms large enough to cover the surface unit heating
element. The use of undersized utensils will expose a
portion of the heating element to direct contact and may
result in ignition of clothing. Proper relationship of utensil to
burner will also improve efficiency.
ꢀ Do Not Clean Door Gasket – The door gasket is essential
for a good seal. Care should be taken not to rub, damage,
or move the gasket.
ꢀ Do Not Use Oven Cleaners – No commercial oven cleaner
or oven liner protective coating of any kind should be used
in or around any part of the oven.
ꢀ Never Leave Surface Units Unattended at High Heat
Settings – Boilover causes smoking and greasy spillovers
that may ignite.
ꢀ Clean Only Parts Listed in Manual.
ꢀ Before Self-Cleaning the Oven – Remove broiler pan and
other utensils.
ꢀ Make Sure Reflector Pans or Drip Bowls Are in Place –
Absence of these pans or bowls during cooking may
subject wiring or components underneath to damage.
For units with ventilating hood –
ꢀ Clean Ventilating Hoods Frequently – Grease should not
be allowed to accumulate on hood or filter.
ꢀ When flambeing foods under the hood, turn the fan on.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS AND FEATURES
This manual covers several different models. The range you have purchased may have some or all of the parts and features listed. The
location and appearance of the features shown here may not match those of your model.
Control Panels
E
F
G
D
A
B
C
A. Left front control knob
B. Surface heating indicator light
C. Left rear control knob
D. Electronic oven control
E. Right rear control knob
F. Right front control knob
G. Surface cooking area locator
OFF
OFF
OFF
OFF
LO
HI
LO
HI
BROIL
SURFACE
HEATING
OVEN
HEATING
150
200
OFF
OFF
2
8
2
8
500
BROIL
BAKE
LO
HI
LO
HI
450
3
7
3
7
2
8
2
8
250
400
4
6
4
6
300
5
350
5
3
7
3
7
4
6
4
6
5
5
E
F
A
B
C
D
G
H
I
A. Left front control knob
B. Left rear control knob
C. Surface heating indicator light
D. Bake and broil oven control knob
E. Oven temperature control knob
F. Oven heating indicator light
G. Right rear control knob
H. Right front control knob
I. Surface cooking area locator
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Range
F
A
G
H
L
I
J
K
B
C
D
E
A. Surface cooking area or element
B. Anti-tip bracket
C. Door stop clip
D. Model and serial number plate
(behind left side of storage drawer)
E. Storage drawer
F. Control panel
G. Hot surface indicator light
(on ceramic glass models)
H. Automatic oven light switch
(on some models)
I. Gasket
J. Broil element (not shown)
K. Bake element
Parts and Features not shown
(on some models)
Coil elements
Oven door window
Oven light
Manual oven light switch
L. Self-clean latch (on some models)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
COOKTOP USE
Cooktop Controls
Ceramic Glass
(on some models)
The surface cooking area will glow red when an element is on. It
will cycle on and off, at all settings, to maintain the selected heat
level.
WARNING
It is normal for the surface of white or biscuit ceramic glass to
appear to change color when surface cooking areas are hot. As
the glass cools, it will return to its original color.
Wiping off the cooktop before and after each use will help keep it
free from stains and provide the most even heating. On cooktops
with white or biscuit ceramic glass, soils and stains may be more
visible, and may require more cleaning and care. For more
information, see “General Cleaning” section.
Fire Hazard
Turn off all controls when done cooking.
Failure to do so can result in death or fire.
ꢀ
ꢀ
ꢀ
Do not store jars or cans above the cooktop. Dropping a
heavy or hard object onto the cooktop could crack the
cooktop.
The control knobs can be set to anywhere between HI and LO.
Push in and turn to setting. On some models, the surface cooking
area locator shows which element is turned on. Use the following
chart as a guide when setting heat levels.
Do not leave a hot lid on the cooktop. As the cooktop cools,
air can become trapped between the lid and the cooktop,
and the ceramic glass could break when the lid is removed.
For foods containing sugar in any form, clean up all spills and
soils as soon as possible. Allow the cooktop to cool down
slightly. Then, while wearing oven mitts, remove the spills
while the surface is still warm. If sugary spills are allowed to
cool down, they can adhere to the cooktop and can cause
pitting and permanent marks.
SETTING
HI
RECOMMENDED USE
ꢀ
ꢀ
Start food cooking.
Bring liquid to a boil.
Medium High
6-8
ꢀ
ꢀ
Hold a rapid boil.
ꢀ
Do not slide cookware or bakeware across the cooktop.
Aluminum or copper bottoms and rough finishes on
cookware or bakeware could leave scratches or marks on the
cooktop.
Quickly brown or sear food.
Medium
5
ꢀ
ꢀ
Maintain a slow boil.
Fry or sauté foods.
ꢀ
ꢀ
Do not cook popcorn in prepackaged aluminum containers
on the cooktop. They could leave aluminum marks that
cannot be removed completely.
Medium Low
2-4
ꢀ
ꢀ
Cook soups, sauces and gravies.
Stew or steam food.
Do not allow objects that could melt, such as plastic or
aluminum foil, to touch any part of the entire cooktop.
LO
ꢀ
ꢀ
ꢀ
Simmer.
ꢀ
ꢀ
Do not use the cooktop as a cutting board.
Keep food warm.
Melt chocolate or butter.
Use cookware about the same size as the surface cooking
area. Cookware should not extend more than ½" (1.3 cm)
outside the area.
B
REMEMBER: When range is in use or (on some models)
during the Self-Cleaning cycle, the entire cooktop area may
become hot.
A
NOTE: On self-cleaning models, the cooktop will not operate
when the range is in a self-cleaning mode.
C
A. Surface cooking area
B. Cookware/canner
C. ½" (1.3 cm) Maximum overhang
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
Use flat-bottomed cookware for best heat conduction and
energy efficiency. Cookware with rounded, warped, ribbed or
dented bottoms could cause uneven heating and poor
cooking results.
To Replace:
1. Line up openings in the burner bowl with the coil element
receptacle.
Determine flatness by placing the straight edge of a ruler
across the bottom of the cookware. While you rotate the ruler,
no space or light should be visible between it and the
cookware.
ꢀ
ꢀ
Cookware designed with slightly indented bottoms or small
expansion channels can be used.
2. Holding the coil element as level as possible, slowly push the
Make sure the bottoms of pots and pans are clean and dry
before using them. Residue and water can leave deposits
when heated.
coil element terminal into the receptacle.
3. When the terminal is pushed into the receptacle as far as it
will go, push down the edge of the coil element opposite the
receptacle.
ꢀ
Do not cook foods directly on the cooktop.
Hot Surface Indicator Light (under ceramic glass)
The hot surface indicator light will glow as long as any surface
cooking area is too hot to touch, even after the surface cooking
area(s) is turned off.
Lift-up Cooktop
(on some models)
The lift-up cooktop provides easy access for cleaning beneath.
Do not drop the cooktop. Damage could occur to the finish and
the cooktop frame. For more information, see the “General
Cleaning” section.
Coil Elements and Burner Bowls
(on some models)
Coil elements should be level for optimal cooking results. Burner
bowls, when clean, reflect heat back to the cookware. They also
help catch spills.
To Lift:
Lift the cooktop by both front corners until the supports lock into
place.
Cookware should not extend more than ½" (1.3 cm) over the coil
element. If cookware is uneven or too large, it can produce
excess heat, causing the burner bowl to change color. For more
information, see the “General Cleaning” section.
NOTE: Before removing or replacing coil elements and burner
bowls, make sure they are cool and the control knobs are in the
Off position.
To Remove:
1. Push in the edge of coil element toward the receptacle. Then
To Replace:
lift it enough to clear the burner bowl.
1. Lift the cooktop from both sides while pressing the support
rods back to unlock them.
2. Slowly lower the cooktop into place.
Home Canning
When canning for long periods, alternate the use of surface
cooking areas, elements or surface burners between batches.
This allows time for the most recently used areas to cool.
2. Pull the coil element straight away from the receptacle.
ꢀ
Center the canner on the grate or largest surface cooking
area or element. On electric cooktops, canners should not
extend more than ½" (1.3 cm) beyond the surface cooking
area or element.
ꢀ
Do not place canner on 2 surface cooking areas, elements or
surface burners at the same time.
ꢀ
ꢀ
On ceramic glass models, use only flat-bottomed canners.
On coil element models, the installation of a Canning Unit Kit
is recommended. If a kit is not installed, the life of the coil
element will be shortened. See “Assistance or Service” for
instructions on how to order.
3. Lift out the burner bowl.
ꢀ
For more information, contact your local agricultural
department. Companies that manufacture home canning
products can also offer assistance.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cookware
ELECTRONIC OVEN CONTROL
IMPORTANT: Do not leave empty cookware on a hot surface
cooking area, element or surface burner.
A
B
C D E
F
Ideal cookware should have a flat bottom, straight sides and a
well-fitting lid, and the material should be of medium-to-heavy
thickness.
Rough finishes may scratch the cooktop or grates. Aluminum and
copper may be used as a core or base in cookware. However,
when used as a base they can leave permanent marks on the
cooktop or grates.
Cookware material is a factor in how quickly and evenly heat is
transferred, which affects cooking results. A nonstick finish has
the same characteristics as its base material. For example,
aluminum cookware with a nonstick finish will take on the
properties of aluminum.
Cookware with nonstick surfaces should not be used under the
broiler.
I
H
K
J
G
A. Oven display
B. Clock
C. Timer/cancel
G. Temperature/time
H. Cook time
I. Start time
Use the following chart as a guide for cookware material
characteristics.
D. Start/enter (control lock)
E. Auto clean
F. Off/cancel
J. Custom broil
K. Bake
COOKWARE
Aluminum
CHARACTERISTICS
ꢀ
ꢀ
ꢀ
Heats quickly and evenly.
Suitable for all types of cooking.
Medium or heavy thickness is best for
most cooking tasks.
Oven Indicator Lights
The indicator lights are located along all 4 sides of the display.
The indicator lights light up or flash when the oven is in one of the
following modes: Bake, Broil, Clean (on some models), On,
Start?, Controls Locked, Door Locked (on some models), Delay,
Timer, Temp, Cook Time, or Start Time.
Cast iron
ꢀ
ꢀ
ꢀ
Heats slowly and evenly.
Good for browning and frying.
Maintains heat for slow cooking.
Ceramic or
ꢀ
ꢀ
ꢀ
Follow manufacturer’s instructions.
Heats slowly, but unevenly.
Display
Ceramic glass
When power is first supplied to the appliance, “PF” or a flashing
time will appear on the display. Press OFF/CANCEL to clear.
Ideal results on low to medium heat
settings.
If “PF” or a flashing time appears at any other time, a power
failure has occurred. Press OFF/CANCEL and reset the clock if
needed.
Copper
ꢀ
Heats very quickly and evenly.
When the oven is in use, the display shows preheat time or oven
temperature setting.
Earthenware
ꢀ
ꢀ
Follow manufacturer’s instructions.
Use on low heat settings.
When the oven is not in use, the display shows the time of day.
When using Start Time/Cook Time, the display will show either
hours and minutes, or minutes and seconds.
Porcelain
enamel-on-
steel or cast
iron
ꢀ
See stainless steel or cast iron.
If Start/Enter is not pressed after setting a function, the “Start?”
oven indicator light will begin flashing after 5 seconds.
Stainless steel
ꢀ
ꢀ
Heats quickly, but unevenly.
Start/Enter
A core or base of aluminum or copper
on stainless steel provides even
heating.
The Start/Enter pad begins any oven function. If the Start/Enter
pad is not pressed within 5 seconds after pressing a function
pad, the “Start?” indicator light will flash as a reminder.
If Start/Enter is not pressed within 1 minute after pressing a
function pad, the oven display will return to the time of day mode
and the programmed function will be canceled.
Off/Cancel
The Off/Cancel pad stops any function except the Clock, Timer
and Control Lock.
The cooling fan may continue to operate after an oven function
has been canceled, depending on oven temperature.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Clock
Control Lock
This is a 12-hour clock and does not show a.m. or p.m.
The Control Lock shuts down the control panel pads to avoid
unintended use of the oven.
To Set:
When the control is locked, only the Clock and Timer pads will
function.
Before setting, make sure the oven and Timer are off.
1. Press CLOCK.
To Lock/Unlock Control: Before locking, make sure the oven
and Timer are off. Touch and hold START/ENTER for 5 seconds.
A single tone will sound, and “LOC” and “LOCK’D” (on some
models) will appear on the display. “LOC” will also appear
whenever any command pad is pressed while the control is
locked.
2. Press the TEMP/TIME “up” or “down” arrow pad to set the
time of day.
3. Press START/ENTER or CLOCK.
Tones
Repeat to unlock. “LOC” and “LOCK’D” (on some models) will
disappear from the display.
Tones are audible signals, indicating the following:
One tone
Oven Temperature Control
ꢀ
ꢀ
ꢀ
ꢀ
Valid pad press
IMPORTANT: Do not use a thermometer to measure oven
temperature because opening the oven door and element or
burner cycling may give incorrect readings.
Oven is preheated (long tone)
Function has been entered
The oven provides accurate temperatures; however, it may cook
faster or slower than your previous oven, so the temperature
calibration can be adjusted.
Reminder, repeating each minute after the end-of-cycle tones
Three tones
A minus sign means the oven will be cooler by the displayed
amount. The absence of a sign means the oven will be warmer by
the displayed amount. Use the following chart as a guide.
ꢀ
Invalid pad press
Four tones
ꢀ
End of cycle
ADJUSTMENT °F
10°F (5°C)
COOKS FOOD
...a little more
...moderately more
...much more
Fahrenheit and Celsius
The temperature is preset at Fahrenheit, but can be changed to
Celsius on some models.
20°F (10°C)
30°F (15°C)
To Change: Press and hold CUSTOM BROIL for 5 seconds. A
tone will sound, and “°C” will appear on the display. Repeat to
change back to Fahrenheit. To exit mode, press OFF/CANCEL.
-10°F (-5°C)
-20°F (-10°C)
-30°F (-15°C)
...a little less
...moderately less
...much less
Timer
The Timer can be set in hours or minutes up to 12 hours and
59 minutes and counts down the set time.
NOTE: The Timer does not start or stop the oven.
To Adjust Oven Temperature Calibration:
1. Press and hold BAKE for 5 seconds until the oven display
shows the current calibration, for example “00.”
To Set:
1. Press TIMER CANCEL*.
2. Press the TEMP/TIME “up” or “down” arrow pad to increase
or to decrease the temperature in 10°F (5°C) amounts. The
adjustment can be set between 30°F (15°C) and
-30°F (-15°C).
The timer oven indicator light will light up. If no action is taken
after 1 minute, the display will return to the time of day mode.
2. Press the TEMP/TIME “up” or “down” arrow pad to set the
length of time.
NOTE: All temperature adjustments will be displayed in
Fahrenheit.
3. Press START/ENTER.
When the set time ends, four 1-second tones will sound.
3. Press START/ENTER.
4. Press TIMER CANCEL* anytime to cancel the timer and/or
stop reminder tones. To cancel the timer during the
countdown, press TIMER CANCEL* twice.
To Adjust Oven Temperature Calibration (on models with
manual oven control):
1. Make sure the oven temperature control knob is in the Off
position. Pull oven temperature control knob straight off and
turn it over.
The time can be reset during the countdown by repeating the
above steps. To display the time of day when the timer is
counting down, press CLOCK.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Loosen the locking screws inside the oven temperature
To raise the temperature, hold the knob handle firmly and turn
the skirt clockwise to move the tooth a notch to the right.
control knob.
Each notch equals about 5°F (3°C).
B
B
A
A
A. Locking screws
B. Notches
C
3. Adjust temperature.
A. Notches
B. Tooth
C. Skirt
To lower the temperature, hold the knob handle firmly and
turn skirt counterclockwise to move the tooth a notch to the
left.
4. Tighten the locking screws and replace knob.
OVEN USE
Odors and smoke are normal when the oven is used the first few
times, or when it is heavily soiled.
FOOD
RACK POSITION(S)
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off. Exposure to the fumes may result in death to
certain birds. Always move birds to another closed and well-
ventilated room.
Frozen pies, large roasts, turkeys,
angel food cakes
1 or 2
Bundt cakes, most quick breads,
yeast breads, casseroles, meats
2
Aluminum Foil
Cookies, biscuits, muffins, cakes,
nonfrozen pies
2 or 3
IMPORTANT: Do not line the oven bottom with any type of foil,
liners or cookware because permanent damage will occur to the
oven bottom finish.
ꢀ
Do not cover entire rack with foil because air must be able to
move freely for best cooking results.
BAKEWARE
Hot air must be able to circulate around food to cook evenly, so
allow 2" (5 cm) of space around bakeware and oven walls. Use
the following chart as a guide.
ꢀ
To catch spills, place foil on rack below dish. Make sure foil is
at least ½" (1.3 cm) larger than the dish and that it is turned
up at the edges.
NUMBEROF POSITION ON RACK
PAN(S)
Positioning Racks and Bakeware
1
Center of rack.
IMPORTANT: To avoid permanent damage to the porcelain
finish, do not place food or bakeware directly on the oven door or
bottom.
2
Side by side or slightly staggered.
3 or 4
Opposite corners on each rack. Make sure
that no bakeware piece is directly over
another.
RACKS
NOTES:
ꢀ
ꢀ
ꢀ
Position racks before turning on the oven.
Do not move racks with bakeware on them.
Make sure racks are level.
To move a rack, pull it out to the stop position, raise the front
edge, then lift out. Use the following illustration and chart as a
guide.
5
4
3
2
1
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Bakeware
Oven Vent
The bakeware material affects cooking results. Follow
A
manufacturer’s recommendations and use the bakeware size
recommended in the recipe. Use the following chart as a guide.
A
BAKEWARE/
RESULTS
RECOMMENDATIONS
Light colored
aluminum
ꢀ
Use temperature and time
recommended in recipe.
A. Oven vent (ceramic
glass model)
A. Oven vent (coil
element model)
ꢀ
Light golden
crusts
The oven vent releases hot air and moisture from the oven, and
should not be blocked or covered. Blocking or covering the vent
will cause poor air circulation, affecting cooking and cleaning
results. Do not set plastics, paper or other items that could melt
or burn near the oven vent.
ꢀ
Even browning
Dark aluminum and
other bakeware with
dark, dull and/or
nonstick finish
ꢀ
May need to reduce baking
temperatures 25°F (15°C).
ꢀ
ꢀ
Use suggested baking time.
On coil element models, the element can be used when the oven
is in use as long as the cookware does not extend more than
½" (1.3 cm) over the element.
For pies, breads and casseroles,
use temperature recommended in
recipe.
ꢀ
Brown, crisp
crusts
Baking and Roasting
ꢀ
Place rack in center of oven.
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting, it is
not necessary to wait for the oven preheat conditioning time to
end before putting food in unless recommended in the recipe.
Insulated cookie
sheets or baking
pans
ꢀ
ꢀ
Place in the bottom third of oven.
May need to increase baking time.
ꢀ
Little or no
bottom browning
To Bake or Roast:
1. Press BAKE. The bake oven indicator light will light up.
2. Set the temperature (optional).
Stainless steel
ꢀ
May need to increase baking time.
Press TEMP/TIME “up” or “down” arrow pad to set a
temperature other than 350°F (177ºC) in 5°F (3ºC) amounts.
The bake range can be set between 170°F (77ºC) and
500°F (260ºC).
ꢀ
Light, golden
crusts
ꢀ
Uneven browning
When the oven temperature is greater than 170°F (77ºC), no
preheat conditioning time will be shown in the display.
Stoneware/Baking
stone
ꢀ
ꢀ
Follow manufacturer’s
instructions.
The preheat conditioning time will not change if the
temperature is reset before the countdown time ends.
ꢀ
Crisp crusts
Ovenproof
glassware, ceramic
glass or ceramic
May need to reduce baking
temperatures 25°F (15°C).
If baking and roasting while the minute timer is counting
down, the set temperature can be seen for 5 seconds by
pressing BAKE.
ꢀ
Brown, crisp
crusts
3. Press START/ENTER.
The oven control automatically sets preheating times based
on the oven temperature selected.
The temperature can be changed after this step. START/
ENTER does not need to be pressed again.
Meat Thermometer
On models without a temperature probe, use a meat
thermometer to determine doneness of meat, poultry and fish.
The internal temperature, not appearance, should be used to
determine doneness. A meat thermometer is not supplied with
this appliance.
After the oven is preheated and the countdown time is
finished, a 1-second tone will sound, the ON indicator light
will go off and the set temperature will appear on the display.
4. Press OFF/CANCEL when finished.
ꢀ
ꢀ
ꢀ
Insert the thermometer into the center of the thickest portion
of the meat or inner thigh or breast of poultry. The tip of the
thermometer should not touch fat, bone or gristle.
After reading the thermometer once, push it into the meat
½" (1.3 cm) more and read again. If the temperature drops,
cook the meat or poultry longer.
Check all meat, poultry and fish in 2 or 3 different places.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Preheating
Custom Broiling
If foods are cooking too fast, press the TEMP/TIME “up” or
“down” arrow pad until 325°F (163°C) shows on the display.
After START/ENTER is pressed, the oven will enter a timed
preheat conditioning. “PrE” and the time countdown will appear
on the display. When the preheat conditioning time ends, a tone
will sound and the selected temperature will appear on the
display.
1. Press CUSTOM BROIL to broil foods slower from the start of
cooking.
2. Press the TEMP/TIME “up” or “down” arrow pad to enter a
Preheat temperatures are affected by varying factors such as
room temperature and peak energy usage times. It is normal for
the temperature showing on the display and the actual oven
temperature to differ.
temperature between 300°F and 500°F (149°C and 260°C).
3. Press START/ENTER.
4. Press OFF/CANCEL when finished.
Waiting an additional 10 minutes after the preheat conditioning
time ends to put food in the oven is suggested when baking
foods with leavening ingredients, such as yeast, baking powder,
baking soda and eggs.
BROILING CHART
For best results, place food 3" (7 cm) or more from the broil
element. Times are guidelines only and may need to be adjusted
for individual foods and tastes. Recommended rack positions are
numbered from the bottom (1) to the top (5). For diagram, see the
“Positioning Racks and Bakeware” section.
Broiling and Custom Broiling
Broiling uses direct radiant heat to cook food. Changing the
temperature when Custom Broiling allows more precise control
when cooking. The lower the temperature, the slower the
cooking. Thicker cuts and unevenly shaped pieces of meat, fish
and poultry may cook better at lower broiling temperatures.
COOK TIME
RACK
POSITION
(in minutes)
FOOD
Side 1
Side 2
Steak
ꢀ
For best results, use a broiler pan and grid. They are
1" (2.5 cm) thick
medium rare
medium
designed to drain juices and help avoid spatter and smoke.
4
4
4
14-15
15-16
18-19
7-8
If you would like to purchase a broiler pan, one may be
ordered. See “Assistance or Service” section to order. Ask for
Part Number 4396923.
8-9
well-done
9-10
Ground meat patties*
³ꢀ₄" (2 cm) thick
well-done
ꢀ
For proper draining, do not cover the grid with foil. The
bottom of the pan may be lined with aluminum foil for easier
cleaning.
4
4
13-14
20-22
7-8
ꢀ
ꢀ
Trim excess fat to reduce spattering. Slit the remaining fat on
the edges to avoid curling.
Pork chops
1" (2.5 cm) thick
10-11
Pull out oven rack to stop position before turning or removing
food. Use tongs to turn food to avoid the loss of juices. Very
thin cuts of fish, poultry or meat may not need to be turned.
Ham slice, precooked
¹ꢀ₂" (1.25 cm) thick
4
4
8-10
5-7
4-5
3-4
ꢀ
After broiling, remove the pan from the oven when removing
the food. Drippings will bake on the pan if left in the heated
oven, making cleaning more difficult.
Frankfurters
Lamb chops
1" (2.5 cm) thick
Before broiling, position rack according to the Broiling Chart. It is
not necessary to preheat the oven before putting food in unless
recommended in the recipe. Position food on grid in the broiler
pan, then place it in the center of the oven rack. Close the door to
the broil stop position to ensure proper broiling temperature.
4
14-17
8-9
Chicken
bone-in pieces
boneless breasts
3
4
17-20
11-16
17-20
11-16
Fish Fillets
¹ꢀ₄-¹ꢀ₂" (0.6-1.25 cm) thick
Fish Steaks
4
4
8-10
4-5
8-9
1" (2.5 cm) thick
16-18
*Place up to 9 patties, equally spaced, on broiler grid.
To Broil:
1. Press CUSTOM BROIL. The broil oven indicator light will light
up.
2. Press START/ENTER. The On and Heat oven indicator lights
will light up.
The temperature setting can be changed any time before or
after pressing START/ENTER. See “Custom Broiling” section.
If broiling while the time is counting down, the set broiling
temperature can be seen for 5 seconds by pressing CUSTOM
BROIL.
3. Press OFF/CANCEL when finished.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Timed Cooking
6. Press OFF/CANCEL or open the oven door to clear the
display.
WARNING
Food Poisoning Hazard
To Set a Delayed Cook Time:
Before setting, make sure the clock is set to the correct time of
day. See “Clock” section.
Do not let food sit in oven more than one hour before
or after cooking.
1. Press BAKE.
Doing so can result in food poisoning or sickness.
2. Set the temperature (optional).
Press the TEMP/TIME “up” or “down” arrow pads to enter a
temperature other than the one displayed.
Timed Cooking allows the oven to be set to cook in 2 different
ways. The oven can be set to start cooking immediately and shut
off automatically at the end of the cooking time. Or, the oven can
be set to start at a later time, cook for a specified length of time
and shut off automatically at the end of the cooking time.
3. Press COOK TIME.
The cook time oven indicator light will light up.
4. Press the TEMP/TIME “up” or “down” arrow pads to enter the
Foods that require a preheated oven should not be cooked using
a delayed function.
length of time to cook.
5. Press START TIME.
To Set a Cook Time:
The start time/delay oven indicator light will light up.
1. Press BAKE. The bake oven indicator light will light up.
6. Press the TEMP/TIME “up” or “down” arrow pads to enter the
2. Set the temperature (optional).
time of day to start.
Press the TEMP/TIME “up” or “down” arrow pads to enter a
temperature other than the one displayed.
7. Press START/ENTER.
When the start time is reached, the oven will automatically
turn on.
3. Press COOK TIME. The cook time oven indicator light will
light up.
The temperature and/or time settings can be changed
anytime after pressing START/ENTER by repeating steps 2-7.
4. Press TEMP/TIME “up” or “down” arrow pads to enter the
length of time to cook.
When the set cook time ends, the oven will shut off
automatically and “End” will appear on the display.
5. Press START/ENTER.
The display will count down the time.
8. Press OFF/CANCEL or open the oven door to clear the
When the time ends, the oven will shut off automatically and
“End” will appear on the display.
display.
RANGE CARE
Self-Cleaning Cycle (on some models)
Do not block the oven vent(s) during the Self-Cleaning cycle. Air
must be able to move freely. Depending on your model, see
“Oven Vent” or “Oven Vents” section.
WARNING
Do not clean, rub, damage or move the oven door gasket. The
door gasket is essential for a good seal.
Prepare Oven:
ꢀ
ꢀ
ꢀ
ꢀ
Remove the broiler pan, grid, cookware and bakeware and,
on some models, the temperature probe from the oven.
Burn Hazard
Remove any foil from the oven because it may burn or melt,
damaging the oven.
Do not touch the oven during the Self-Cleaning cycle.
Keep children away from oven during
Self-Cleaning cycle.
Remove oven racks to keep them shiny and easy to slide.
See “General Cleaning” section for more information.
Failure to follow these instructions can result in burns.
Hand clean inside door edge and the 1½" (3.8 cm) area
around the inside oven cavity frame, being certain not to
move or bend the gasket. This area does not get hot enough
during self-cleaning to remove soil. Do not let water, cleaner,
etc. enter slots on door frame. Use a damp cloth to clean this
area.
IMPORTANT: The health of some birds is extremely sensitive to
the fumes given off during the Self-Cleaning cycle. Exposure to
the fumes may result in death to certain birds. Always move birds
to another closed and well-ventilated room.
ꢀ
Wipe out any loose soil to reduce smoke and avoid damage.
At high temperatures, foods react with porcelain. Staining,
etching, pitting or faint white spots can result. This will not
affect cooking performance.
Self-clean the oven before it becomes heavily soiled. Heavy soil
results in longer cleaning and more smoke.
Keep the kitchen well-ventilated during the Self-Cleaning cycle to
help get rid of heat, odors, and smoke.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Prepare Cooktop and Storage Drawer:
To Self-Clean:
ꢀ
Remove plastic items from the cooktop because they may
melt.
Before self-cleaning, make sure the door is closed completely or
it will not lock and the cycle will not begin.
1. Press AUTO CLEAN.
ꢀ
Remove all items from the storage drawer.
2. Press the TEMP/TIME “up” or “down” arrow pad to set a
clean time other than 3 hours 30 minutes. The clean time can
be set between 2 hours 30 minutes and 4 hours 30 minutes.
How the Cycle Works
IMPORTANT: The heating and cooling of porcelain on steel in the
oven may result in discoloring, loss of gloss, hairline cracks and
popping sounds.
3. Press START/ENTER.
The oven door will automatically lock. The ON and DOOR
LOCKED oven indicator lights will light up. The door will not
unlock until the oven cools.
The Self-Cleaning cycle uses very high temperatures, burning soil
to a powdery ash.
The oven is preset for a 3 hour 30 minute clean cycle, but
the time can be changed. Suggested clean times are
2 hours 30 minutes for light soil and between 3 hours 30 minutes
and 4 hours 30 minutes for average to heavy soil.
When the cycle is complete and the oven cools, “End” will
appear on the oven display and the oven indicator lights will
go off.
4. Press OFF/CANCEL to clear the oven display.
Once the oven has completely cooled, remove ash with a damp
cloth. Do not wipe down any of the inside surfaces until the oven
has completely cooled down. Applying a cool, damp cloth to the
inner door glass before it has cooled completely could result in
the glass breaking.
To Stop Self-Clean anytime:
Press OFF/CANCEL. If the oven temperature is too high, the door
will remain locked. It will not unlock until the oven cools.
The oven light will not work during the Self-Cleaning cycle.
General Cleaning
IMPORTANT: Before cleaning, make sure all controls are off and
the oven and cooktop are cool. Always follow label instructions
on cleaning products.
Cooktop Cleaner Part Number 31464 is recommended regularly
to help avoid scratches, pitting and abrasions and to condition
the cooktop, and can be ordered as an accessory. See
“Assistance or Service” section to order.
Soap, water and a soft cloth or sponge are suggested first unless
otherwise noted.
Cooktop Scraper Part Number 3183488 is also recommended for
stubborn soils, and can be ordered as an accessory. See
“Assistance or Service” section to order. The Cooktop Scraper
uses razor blades. Store razor blades out of the reach of
children.
EXTERIOR PORCELAIN ENAMEL SURFACES (on some
models)
Food spills containing acids, such as vinegar and tomato, should
be cleaned as soon as the entire appliance is cool. These spills
may affect the finish.
Light to moderate soil
ꢀ
Paper towels or clean damp sponge:
Clean while the cooktop is still warm. You may want to wear
oven mitts while cleaning the cooktop.
Cleaning Method:
ꢀ
Glass cleaner, mild liquid cleaner or nonabrasive scrubbing
pad:
Sugary spills (jellies, candy, syrup)
Gently clean around the model and serial number plate
because scrubbing may remove numbers.
ꢀ
Cooktop Scraper:
Clean while the cooktop is still warm. You may want to wear
oven mitts while cleaning the cooktop.
ꢀ
All-Purpose Appliance Cleaner Part Number 31662 (not
included):
See “Assistance or Service” section to order.
ꢀ
Cooktop Polishing Creme and clean damp paper towel:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears.
STAINLESS STEEL (on some models)
Heavy soil, dark streaks, specks and discoloration
Cleaning Method:
Rub in direction of grain to avoid damaging.
ꢀ
Cooktop Polishing Creme or nonabrasive cleanser:
Rub product into soil with a damp paper towel or soft cloth.
Continue rubbing until white film disappears.
ꢀ
ꢀ
ꢀ
Stainless Steel Cleaner & Polish Part Number 31462 (not
included): See “Assistance or Service” section to order.
Burned-on soil
ꢀ
Cooktop Cleaner and Cooktop Scraper:
Liquid detergent or all-purpose cleaner: Rinse with clean
water and dry with soft, lint-free cloth.
Rub creme into soil with damp paper towel. Hold scraper as
flat as possible on surface and scrape. Repeat for stubborn
spots. Polish entire cooktop with creme and paper towel.
Vinegar for hard water spots
To avoid damage to stainless steel, do not use soap-filled
scouring pads, abrasive cleaners, Cooktop Polishing Creme,
steel-wool pads, gritty washcloths or some paper towels.
Metal marks from aluminum and copper
ꢀ
Cooktop Cleaner:
Clean as soon as cooktop has cooled down. Rub creme into
surface with a damp paper towel or soft cloth. Continue
rubbing until white film disappears. The marks will not totally
disappear, but after many cleanings they will become less
noticeable.
CERAMIC GLASS (on some models)
Cleaning Method:
Always wipe with a clean, wet cloth or sponge and dry thoroughly
to avoid streaking and staining.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Tiny scratches and abrasions
OVEN DOOR EXTERIOR
Cleaning Method:
ꢀ
Cooktop Cleaner:
Rub creme into surface with a damp paper towel or soft
cloth. Continue rubbing until white film disappears. Scratches
and abrasions do not affect cooking performance, and after
many cleanings they will become less noticeable.
ꢀ
Glass cleaner and a soft cloth or sponge:
Apply glass cleaner to soft cloth or sponge, not directly on
panel.
Do not use steel wool, abrasive powder cleansers, chlorine
bleach, rust remover or ammonia because damage may occur.
ꢀ
All-Purpose Appliance Cleaner Part Number 31662 (not
included):
See “Assistance or Service” section to order.
COOKTOP CONTROLS
Cleaning Method:
OVEN CAVITY
When replacing knobs, make sure knobs are in the Off position.
On some models, do not remove seals under knobs.
Food spills should be cleaned when oven cools. At high
temperatures, foods react with porcelain and staining, etching,
pitting or faint white spots can result.
ꢀ
Soap and water or dishwasher:
Pull knobs straight away from control panel to remove.
Cleaning Method:
Do not use steel wool, abrasive cleansers or oven cleaner.
Do not soak knobs.
ꢀ
Self-Cleaning cycle: See “Self-Cleaning Cycle” first.
Do not use oven cleaners.
CONTROL PANEL
Cleaning Method:
OVEN RACKS AND ROASTING RACKS
Cleaning Method:
ꢀ
Glass cleaner and soft cloth or sponge: Apply glass cleaner
to soft cloth or sponge, not directly on panel.
ꢀ
Self-Cleaning cycle: See “Self-Cleaning Cycle” first. Remove
racks or they will discolor and become harder to slide. If this
happens, a light coating of vegetable oil applied to the rack
guides will help them slide.
ꢀ
All-Purpose Appliance Cleaner Part Number 31662 (not
included):
See “Assistance or Service” section to order.
ꢀ
Steel-wool pad
Do not use abrasive cleaners, steel-wool pads, gritty washcloths
or some paper towels. Damage may occur.
BROILER PAN AND GRID (on selected models)
COIL ELEMENTS (on some models)
Cleaning Method:
Chrome only
Cleaning Method:
ꢀ
Mildly abrasive cleanser:
ꢀ
Damp cloth: Make sure control knobs are off and elements
are cool.
Scrub with wet scouring pad.
Do not clean or immerse in water. Soil will burn off when hot.
For more information, see “Coil Elements and Burner Bowls.”
ꢀ
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Soak for 20 minutes, then scrub with scouring or steel-wool
pad.
BURNER BOWLS (on some models)
ꢀ
Oven cleaner: Follow product label instructions.
Porcelain enamel only
Dishwasher
Cleaning Method:
Chrome only
ꢀ
Do not clean in the Self-Cleaning cycle.
ꢀ
Solution of ¹ꢀ₂ cup (125 mL) ammonia to 1 gal. (3.75 L) water:
Soak for 20 minutes, then scrub with stainless steel-wool
pad.
STORAGE DRAWER (on some models)
ꢀ
ꢀ
Oven cleaner: Follow product label instructions.
Make sure drawer is cool and empty before cleaning.
For more information, see “Storage Drawer” section.
Cleaning Method:
Mildly abrasive cleanser: Scrub with wet scouring pad.
Porcelain enamel only
ꢀ
Mild detergent
ꢀ
Dishwasher
Drawer Liner (on some models)
Remove all stored items from drawer and lift out drawer liner.
ꢀ
Gas Grate and Drip Pan Cleaner Part Number 31617 (not
included):
See “Assistance or Service” section to order.
ꢀ
Clean with mild detergent.
ꢀ
All-Purpose Appliance Cleaner Part Number 31662 (not
included):
See “Assistance or Service” section to order.
SURFACE UNDER COOKTOP (on some models)
For more information, see “Lift-up Cooktop” section.
Cleaning Method:
ꢀ
Steel-wool pad
Do not remove the cooktop to avoid product damage.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Lift the oven door while holding both sides.
WARMING DRAWER and TRAY (on some models)
Continue to push the oven door closed and pull it away from
the oven door frame.
Make sure drawer is cool and remove tray.
Cleaning Method:
ꢀ
Mild detergent (for both)
ꢀ
All-Purpose Appliance Cleaner Part Number 31662 (not
included):
See “Assistance or Service” section to order.
Oven Light
(on some models)
To Replace:
1. Insert both hanger arms into the door.
The oven light is a standard 40-watt appliance bulb. It will come
on when the oven door is open. The oven light will not work
during the Self-Cleaning cycle. On some models, when the oven
door is closed, press the manual oven light switch on the
backguard to turn on and off.
Before replacing, make sure the oven and cooktop are cool and
the control knobs are in the off position.
To Replace:
1. Unplug range or disconnect power.
2. Turn the glass bulb cover in the back of the oven
counterclockwise to remove.
2. Open the oven door.
You should hear a “click” as the door is set into place.
3. Move the hinge levers back to the locked position. Check
that the door is free to open and close. If it is not, repeat the
removal and installation procedures.
3. Turn bulb counterclockwise to remove from socket.
4. Replace bulb, then bulb cover by turning clockwise.
5. Plug in range or reconnect power.
Storage Drawer
The storage drawer can be removed. Before removing, make sure
drawer is cool and empty.
Oven Door
To Remove:
For normal range use, it is not suggested to remove the oven
door. However, if removal is necessary, make sure the oven is off
and cool. Then, follow these instructions. The oven door is heavy.
1. Pull the storage drawer straight back past the drawer stop
notch and the end of the side rails.
To Remove:
1. Open oven door all the way.
2. Flip up the hinge latch on each side.
B
A
A. Drawer stop notch
B. End of side rail
2. Lift up the back of the drawer and pull the drawer out.
3. Close the oven door as far as it will shut.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Once the drawer is fully engaged on both sides, slide the
To Replace:
drawer back into the closed position.
1. Lift up the back of the drawer and place it inside the range in
its fully forward position.
NOTE: When you are removing and replacing the storage
drawer, a slight push may be needed to move the drawer
stop notch past the drawer glides.
2. Lift up the front of the drawer to a level position.
3. Slowly push the drawer into the range until the drawer side
rails engage with the gap in the drawer glides.
A
A. Engage drawer glide.
TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.
Nothing will operate
Oven will not operate
ꢀ
ꢀ
Is the power supply cord unplugged?
ꢀ
ꢀ
ꢀ
Is the electronic oven control set correctly?
Plug into a grounded outlet.
See “Electronic Oven Control” section.
Has a household fuse blown, or has a circuit breaker
tripped?
Replace the fuse or reset the circuit breaker. If the problem
continues, call an electrician.
Has a delay start been set?
See “Timed Cooking” section.
On some models, is the Control Lock set?
See “Control Lock” section.
Cooktop will not operate
Oven temperature too high or too low
ꢀ
ꢀ
Is the control knob set correctly?
ꢀ
ꢀ
Does the oven temperature calibration need adjustment?
Push in knob before turning to a setting.
See “Oven Temperature Control” section.
On ceramic glass models, is the “Control Lock” set?
See “Control Lock” section.
On some models, does the cooling fan run during BAKE,
BROIL or CLEAN?
It is normal for the fan to automatically run when the oven is
in use. This helps cool the electronic control.
Excessive heat around cookware on cooktop
ꢀ
Is the cookware the proper size?
Oven indicator lights flash
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than ½" (1.3 cm) outside the cooking area.
ꢀ
Do the oven indicator lights flash?
See the “Display” and/or the “Oven Indicator Lights” section.
If the indicator light(s) keeps flashing, call for service. See
“Assistance or Service” section.
Hot Surface indicator light stays on
ꢀ
Does the Hot Surface indicator light stay on after control
knob(s) have been turned off?
Display shows messages
See “Cooktop Controls” section.
ꢀ
ꢀ
Is the display showing “PF” or a flashing time?
There has been a power failure. Clear the display. See
“Display(s)” section. On some models, reset the clock, if
needed. See “Clock” section.
Cooktop cooking results not what expected
ꢀ
ꢀ
ꢀ
Is the proper cookware being used?
See “Cookware” section.
Is the display showing a letter followed by a number?
Depending on your model, press OFF/CANCEL, OFF or
CANCEL/OFF to clear the display. See “Display(s)” section. If
it reappears, call for service. See “Assistance or Service”
section.
Is the control knob set to the proper heat level?
See “Cooktop Controls” section.
Is the appliance level?
Level the appliance. See the Installation Instructions.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Was the oven preheated?
Self-Cleaning cycle will not operate
See “Baking and Roasting” section.
Is the proper bakeware being used?
See “Bakeware” section.
ꢀ
ꢀ
ꢀ
Is the oven door open?
Close the oven door all the way.
Are the racks positioned properly?
See “Positioning Racks and Bakeware” section.
Has the function been entered?
See “Self-Cleaning Cycle” section.
Is there proper air circulation around bakeware?
See “Positioning Racks and Bakeware” section.
On some models, has a delay start Self-Clean cycle been
set?
See “Self-Cleaning Cycle” section.
Is the batter evenly distributed in the pan?
Check that batter is level in the pan.
ꢀ
Has a delay start been set?
See “Timed Cooking” section.
Is the proper length of time being used?
Adjust cooking time.
Oven cooking results not what expected
Has the oven door been opened while cooking?
Oven peeking releases oven heat and can result in longer
cooking times.
ꢀ
ꢀ
ꢀ
Is the appliance level?
Level the appliance. See the Installation Instructions.
ꢀ
ꢀ
Are baked items too brown on the bottom?
Move rack to higher position in the oven.
Is the proper temperature set?
Double-check the recipe in a reliable cookbook.
Are pie crust edges browning early?
Use aluminum foil to cover the edge of the crust and/or
reduce baking temperature.
Is the proper oven temperature calibration set?
See “Oven Temperature Control” section.
ASSISTANCE OR SERVICE
Before calling for assistance or service, please check
“Troubleshooting.” It may save you the cost of a service call. If
you still need help, follow the instructions below.
Estate Brand Home Appliances
Customer eXperience Center
553 Benson Road
Benton Harbor, MI 49022-2692
When calling, please know the purchase date and the complete
model and serial number of your appliance. This information will
help us to better respond to your request.
Please include a daytime phone number in your correspondence.
Accessories U.S.A.
If you need replacement parts
To order accessories, call the Whirlpool Customer eXperience
Center toll free at 1-800-442-9991 and follow the menu prompts.
Accessories Online.”
If you need to order replacement parts, we recommend that you
use only FSP® replacement parts. FSP® replacement parts will fit
right and work right because they are made with the same
precision used to build every new ESTATE® appliance.
To locate FSP® replacement parts in your area, call our Customer
eXperience Center telephone number or your nearest designated
ESTATE® service center.
Canning Unit Kit
(coil element models)
Order Part Number 242905
Call the Whirlpool Customer eXperience Center
toll free: 1-800-253-1301.
Cooktop Cleaner
Our consultants provide assistance with:
(ceramic glass models)
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
Features and specifications on our full line of appliances.
Order Part Number 31464
Installation information.
Cooktop Protectant
Order Part Number 31463
Use and maintenance procedures.
Accessory and repair parts sales.
Cooktop Care Kit
(includes cleaner, protectant, and applicator pads)
Specialized customer assistance (Spanish speaking, hearing
impaired, limited vision, etc.).
Order Part Number 31605
ꢀ
Referrals to local dealers, repair parts distributors, and
service companies. Whirlpool designated service technicians
are trained to fulfill the product warranty and provide after-
warranty service, anywhere in the United States.
Cooktop Scraper
(ceramic glass models)
Order Part Number 3183488
To locate the Whirlpool designated service company in your
area, you can also look in your telephone directory Yellow
Pages.
Stainless Steel Cleaner & Polish
(stainless steel models)
Order Part Number 31462
For further assistance
If you need further assistance, you can write to Whirlpool
Corporation with any questions or concerns at:
All-Purpose Appliance Cleaner
Order Part Number 31662
19
Download from Www.Somanuals.com. All Manuals Search And Download.
WHIRLPOOL CORPORATION MAJOR APPLIANCE WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or
furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for FSP® replacement parts
and repair labor to correct defects in materials or workmanship. Service must be provided by a Whirlpool designated service company.
ITEMS WHIRLPOOL WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters. Those consumable parts are excluded from warranty
coverage.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.
5. Any food loss due to refrigerator or freezer product failures.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery. This major appliance is designed to be repaired in the home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service in remote locations.
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. WHIRLPOOL SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE.
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized Whirlpool dealer to determine if
another warranty applies.
If you need service, first see the “Troubleshooting” section of the Use & Care Guide. After checking “Troubleshooting,” additional help
can be found by checking the “Assistance or Service” section or by calling Whirlpool. In the U.S.A., call 1-800-253-1301. In Canada,
call 1-800-807-6777.
8/05
Keep this book and your sales slip together for future
reference. You must provide proof of purchase or installation
date for in-warranty service.
Write down the following information about your major appliance
to better help you obtain assistance or service if you ever need it.
You will need to know your complete model number and serial
number. You can find this information on the model and serial
number label located on the product.
Dealer name____________________________________________________
Address________________________________________________________
Phone number__________________________________________________
Model number __________________________________________________
Serial number __________________________________________________
Purchase date __________________________________________________
W10017730
© 2005 Whirlpool Corporation.
12/05
Printed in U.S.A.
All rights reserved.
® Registered Trademark/TM Trademark of Whirlpool, U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|