ASSEMBLY INSTRUCTIONS
DX-WD1202
Corner TV Stand
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Tools needed
3
Hammer
No. 2 Phillips screwdriver
Caution: Do not
use an electric drill
or screwdriver
Flatblade screwdriver
Shim
Package contents
Package contents: hardware
Note: You may receive extra hardware with your new TV stand.
Make sure you have all the hardware necessary to assemble your new TV stand:
Label
Hardware
Hidden cam
Qty.
Label
Hardware
Washer
Qty.
Q
30
W
2
Cam dowel
Cam screw
Foot
Pull
X
Y
2
2
2
R
S
22
8
Bumper card
Hole cover
AA
T
1
Warning
label
BB
1
Foot base
Hinge
U
V
1
4
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
4
DX-WD1202
Package contents: hardware (continued)
Using a screw that is too long will cause damage to your stand. Before beginning assembly, separate
each type of screw. Carefully study the screw table below. You can use the ruler at the bottom of the
screw table to measure screws. Pay close attention to the color of each screw.
Letter
Description
Qty.
CC
4
Black 2 1/2" (63.5 mm) large head screw
DD
EE
FF
4
3
8
Black 1 7/8" (47.75 mm) flat head screw
Brown 1 1/2" (38.1 mm) flat head screw
Black 9/16" (14.22 mm) flat head
GG
HH
4
8
Black 9/16" (14.22 mm) pan head screw
Black 1/2" (12.7 mm) flat head screw
II
8
Brown 7/16" (11.17 mm) large head screw
JJ
2
Silver 1/4" (6.35 mm) machine screw
Nails
KK
33
1
2
3
4in
10
20
30
40
50
60
70
80
90
100mm
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
5
Package contents: parts
A End (2)
B Upright (1)
C Lower upright (1)
D Top (1)
E Bottom (1)
F Shelf (1)
G Back (1)
H Door (2)
I Right front and left rear leg (2)
J Left front and right rear leg (2)
K Extension (2)
L Stop molding (1)
M Top molding (1)
N Base (1)
O Top rail (2)
P Bottom rail (2)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
6
DX-WD1202
Assembly instructions
Step1:
Assemble your stand on a carpeted floor or on the empty carton to avoid scratching your stand or the floor.
Push thirty hidden cams (Q) into the ends (A), uprights (B and C), top (D), bottom (E), shelf (F), and one set of
legs (I and J). Then, insert twenty-two cam dowels (R) into the hidden cams. Do not insert cam dowels into
the hidden cams on the end of (A) as indicated in the illustration.
Do not insert cam dowels
into these edges.
Do not tighten the hidden cams in this step.
Arrow
You’ll need:
Q (30)
R (22)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
7
Tightening hidden cams
In the remaining steps, use these illustrations for instructions on tightening hidden cams.
Warning: Risk of damage or injury. Hidden cams must be completely tightened. Hidden cams that are not
completely tightened will loosen, and parts may separate.
A hidden cam (Q) has an arrow. When you insert the hidden cam, make sure that the arrow points toward the
hole in the side of the part you are inserting it into.
Arrow
Make sure that you turn the
hidden cam 210°. Note the
position of the arrow on the
hidden cam.
Arrow
210°
In the illustration below,
the hidden cam has not
been tightened enough.
You’ll need:
Flatblade screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
8
DX-WD1202
Step 2:
Screw two cam screws (S) into each of the legs (two I and two J).
Place the ends (A) flat with the side with the hidden cams facing up.
Make sure that the sides of the legs with the hidden cams are toward the ends (A).
Insert the cam screws on one of the legs (I) into one of the ends (A) and cam screws on one of the legs (J) into
the opposite side of the other end (A).
Tighten the four hidden cams. See “Tightening hidden cams” on page 7.
Leg with
hidden cams
Surface with
hidden cams
Leg with
hidden cams
You’ll need:
Flatblade screwdriver
S (8)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
9
Step 3:
Carefully turn the ends (A) over so the side without the hidden cams is facing up.
Use a Phillips screwdriver to screw eight black 9/16" flat head screws (FF) (four per end) into the ends (A) until
the shoulders of the screws rest on the surface of the ends. Do not screw the screws in all the way.
Align the groove on a top rail (O) over the top screw head on one of the ends (A), then slide the rail over the
other screw head. Make sure that the ends of the rail are flush with the edges of the end. Repeat to attach the
other top rail (O) to the other end (A).
Align the groove on a bottom rail (P) over the bottom screw head on one of the ends (A), then slide the rail
over the other screw head. Make sure that the ends of the rail are flush with the edges of the end. Repeat to
attach the other bottom rail (P) to the other end (A).
Apply pressure with your hand as you
guide the rails over the screws on the
ends.
Screw head
You’ll need:
Phillips screwdriver
FF (8)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
10
DX-WD1202
Step 4:
Carefully turn the ends over so the sides with the hidden cams face up.
Attach the unattached leg (I) to the left end (A) and the unattached leg (J) to the right end (A). See Step 2 for
instructions.
Insert a hole plug (AA) into the holes on the legs (I and J) that you just attached.
This end will now be
referred to the left end.
This end will now be
referred to the right end.
You’ll need:
AA (2)
Flatblade screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Step 5:
11
Fasten the stop molding (L) to the top (D). Use a flatblade screwdriver to tighten the four hidden cams. See
Unfinished
surface
Unfinished surface
Rounded edge
Arrow
210°
You’ll need:
Flatblade screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
12
DX-WD1202
Step 6:
Fasten the upright (B) and the left end (A) with the leg (J) to the top (D) and stop molding (L). Use a flatblade
screwdriver to tighten the five hidden cams (two on the upright (B), two on the left end (A), and one on the
Surface without
hidden cams
Finished edge
Arrow
210°
You’ll need:
Flatblade screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Step 7:
13
Fasten the shelf (F) to the left end (A). Use a flatblade screwdriver to tighten the two hidden cams. See
Fasten the shelf (F) to the upright (B). Use a Phillips screwdriver and two black 1 7/8" flat head screws (DD).
Fasten the lower upright (C) to the shelf (F). Use a flatblade screwdriver to tighten the two hidden cams.
Surface without
hidden cams
Finished
edge
finie
Unfinished
ficie sin acabado
surface
Chant fini
Arrow
210°
You’ll need:
DD (2)
Phillips screwdriver
Flatblade screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
14
DX-WD1202
Step 8:
Fasten the bottom (E) to the left end (A). Use a flatblade screwdriver to tighten the two hidden cams. See
Fasten the bottom (E) to the lower upright (C). Use a Phillips screwdriver and two black 1 7/8" flat head
screws (DD).
Slide the base (N) onto the notched edge of the bottom (E) so that the edge of the base is flush with the leg
on left end (A).
Unfinished surface
Notched edge
Arrow
210°
You’ll need:
DD (2)
Flatblade screwdriver
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
15
Step 9:
Fasten the right end (A) with the leg (I) to the top (D), bottom (E), shelf (F), and stop molding (L). Use a
flatblade screwdriver to tighten the seven hidden cams: A (2), E (2), F(2), and I (1). See “Tightening hidden
Fasten the top molding (M) to the stop molding (L). Use a Phillips screwdriver and three brown 1 1/2" flat
head screws (EE).
Fasten the extension blocks (K) to the bottom (E). Use a Phillips screwdriver and four black 2 1/2" large head
screws (CC).
Arrow
210°
You’ll need:
Flatblade screwdriver
Phillips screwdriver
EE (3)
CC (4)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
16
DX-WD1202
Step 10:
With the top of the unit facing down, fasten the foot base (U) to the extension block (K). Use a Phillips
screwdriver and four black 9/16" pan head screws (GG). Then, push the foot (T) into the foot base (U).
Note: Turn the foot (T) for adjustments. The foot should not extend beyond the bottom edge of the base (N).
You’ll need:
GG (4)
Phillips screwdriver
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Step 11:
17
Carefully turn the unit so the front is facing down, then fasten the back (G) to the legs (I and J). Use a Phillips
screwdriver and eight brown 7/16" large head screws (II).
Fasten the remaining back (G) to your stand using 33 nails (KK).
Note: Be sure to tap the nails into the holes that line up over the shelf (F). Perforations have been provided for access through
the back. Carefully cut out the holes needed.
These holes must line
up over shelf (D).
Caution: Do not stand
your stand upright
without the back
fastened. Your stand may
collapse.
You’ll need:
Phillips screwdriver
KK (33)
II (8)
Hammer
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
18
DX-WD1202
Step 12:
Fasten the hinges (V) to the doors (H). Use a Phillips screwdriver and eight 1/2" flat head screws (HH) (two for
each hinge).
You’ll need:
Phillips screwdriver
HH (8)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Step 13:
19
Carefully turn the unit so the left end is facing down, then fasten one of the doors (H) to the left end (A). Use
a Phillips screwdriver and the screws in the hinges.
Note: You may need to loosen the mounting screw to slide the hinge part way out of the slot. Retighten the screw before you
mount the hinge to the end.
Carefully turn the unit so the right end is facing down, then fasten the other door (H) to the right end (A). Use
a Phillips screwdriver and the screws in the hinges.
Carefully turn the unit so it is right side up.
Align a pull (X) with the screw hole in the middle of the door (H). Place a washer (W) over the screw hole on
the back of the door, then insert a silver 1/4" machine screw (JJ) through the washer and into the pull screw
hole. Tighten the screw. Repeat this step for the other door.
Peel two bumpers from the bumper card (Y) and stick them on the inside of the door where the door comes
in contact with the lower upright (C). Repeat this step for the other door.
Mounting screw
You’ll need:
Phillips screwdriver
W (2)
JJ (2)
Y (4)
X (2)
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
20
DX-WD1202
Step 14:
You may need to adjust the doors to make them fit correctly.
To adjust the doors from side to side (horizontal), loosen the mounting screw several turns, then turn the
horizontal adjusting screw in or out. Tighten the mounting screw after making adjustments.
To adjust the doors up and down (vertical), loosen both vertical adjustment screws. Move the doors up or
down to the best location. Tighten the screws after making adjustments. You can use a shim to help hold the
door in place.
To adjust the doors in or out (depth), loosen the mounting screw one turn and move the doors in or out, as
needed. Tighten the mounting screw after making adjustments.
Horizontal
adjusting screw
Mounting
screw (depth)
Vertical
adjusting screws
Shim
You’ll need:
Phillips screwdriver
Shim
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
DX-WD1202
Step 15:
21
Apply the warning label (BB) to the top (D). You should be able to read the label when the TV is removed
from your stand. When the TV is in place, it should hide the label. Peel off the backing and apply the label as
shown.
Caution: This is a permanent label intended to last for the life of the product. Once applied, do not try to
remove it. You may damage the finish on the top.
Clean with your favorite furniture polish or a damp cloth. Wipe dry. Your stand is ready to use.
Warning: Never use this furniture with a TV
that is too large or too heavy. Severe injury or
death can occur. The TV and furniture will be
unstable and may tip.
•
The TV must weigh less than 95 lbs
(43.09 kg).
The base of the TV must be able to sit
completely on this shelf.
•
95 lbs
(43 kg)
25 lbs
(11 kg)
25 lbs
(11 kg)
40 lbs.
18 kg
Note: One door has been
removed to make the interior
visible.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
22
DX-WD1202
Still need help?
For customer service, call: 800-305-2204 (U.S./Canada markets)
Distributed by Best Buy Purchasing, LLC
7601 Penn Avenue South, Richfield, MN USA 55423-3645
© 2011 BBY Solutions, Inc.
All rights reserved. DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other
products and brand names are trademarks of their respective owners.
Need help? Call 800-305-2204
Download from Www.Somanuals.com. All Manuals Search And Download.
Certificate of Conformity
1. This certificate applies to the Sauder
Woodworking Product identified by this
instruction booklet.
2. This certificate applies to the compliance of
this product with the CPSC Ban on
Lead-Containing Paint (16 CFR 1303).
3. This product was manufactured by:
Sauder Woodworking Company
502 Middle Street
Archbold, Ohio 43502
(419) 446-2711
4. Date of Manufacture: ___________
Lot number: 337023
Distributed by Best Buy Purchasing, LLC
7601 Penn Ave. South, Richfield, MN 55423 U.S.A.
© 2011 BBY Solutions, Inc.
All rights reserved.
DYNEX is a trademark of BBY Solutions, Inc. Registered in some countries. All other products and
brand names are trademarks of their respective owners.
11-0422
ENGLISH
Download from Www.Somanuals.com. All Manuals Search And Download.
|