Owners Manual
Home Systems I Professional I Automotive I Multimedia
Download from Www.Somanuals.com. All Manuals Search And Download.
About this installation manual
This installation manual provides all technical specifications, installation dimensions and crossover connection
2
instructions for the Dynaudio Esotec and Esotar series. To realize the full potential of Dynaudio Automotive
systems, some areas should be addressed, as touched upon in the following pages.
Due to the great variety of installation conditions it will not offer specific instructions how to install the systems
into your car. Please refer to the operating manual of your vehicle or ask your local automotive dealer for further
assistance. To observe all relevant matters and thus maximize the tremendous performance potential of your
Dynaudio in-car loudspeaker system, consult your authorized Dynaudio Automotive loudspeaker dealer for
assistance. Your dealer has the knowledge and expertise to perform a high quality aftermarket installation.
Safety information
2
As all Dynaudio Esotec and Esotar Series components are passive (in that they rely on external amplification),
the components themselves can not cause any damage.
However, the components can be damaged beyond repair unless a few ground rules are observed:
X Insure all components are properly installed and wired correctly.
X Observe the technical specifications.
X Always use high-quality cabling and amplification.
HIGH SOUND PRESSURE LEVELS
CAUTION
Listening to high sound pressure levels over a prolonged period of time
may harm your hearing.
X To avoid auditory effects do not listen to high sound levels over a long period of time.
2
Esotec / Esotar Series
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty
Dynaudio provides a limited manufacturer´s warranty on Dynaudio
Automotive aftermarket products. Please check with your local
distributor for warranty conditions.
This warranty only covers faults or defects in material and production. Damage caused as a result of abuse,
misuse or defective electronics is not covered by the warranty. The warranty will only be valid if the metallic
Dynaudio holographic safety label is on the driver.
The warranty is valid only if the product is purchased from an authorized Dynaudio Automotive aftermarket
dealer. All warranty claims must be accompanied by a copy of the original purchase invoice and warranties are
only valid in the country or market of original origin or distribution. Should warranty service be required, it must
be arranged for in the country of purchase by an authorized Dynaudio dealer.
2
Esotec / Esotar Series
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Tweeters/Midrange
MD 102
MD 142
8 Ω
Esotar2 110
6 Ω
Nominal impedance
8 Ω
Recommended frequency range
2200 – 30000 Hz
700 – 6000 Hz
2000 – 30000 Hz
Power handling
• Nominal long term IEC
• Transient
100 W
500 W
100 W
150 W
1000 W
1000 W
Net weight
0.126 kg
0.75 kg
0.50 kg
Overall dimensions (Ø x D)
62.2 x 43 mm
121 x 66 mm
111 x 41 mm
Woofers
MW 152
4 Ω
MW 162
4 Ω
MW 162 GT
MW 172
MW 182
4 Ω
Esotar2 650 Esotar2 1200
Nominal impedance
4 Ω
4 Ω
4 Ω
4 Ω
Recommended frequency
range
55 – 3500 Hz 40 – 4000 Hz 40 – 4000 Hz 35 – 3500 Hz 30 – 2000 Hz 50 – 4000 Hz
18 – 300 Hz
Power handling
• Nominal long term IEC
• Transient
100 W
120 W
120 W
150 W
180 W
200 W
400 W
1000 W
1000 W
1000 W
1000 W
1000 W
1000 W
1500 W
Net weight
1.1 kg
1.2 kg
1.1 kg
1.3 kg
1.85 kg
1.25 kg
8.8 kg
Overall dimensions (Ø x D) 146 x 70 mm 175 x 77 mm 166 x 71 mm 200 x 88 mm 239 x 86 mm 169 x 78 mm 297 x 162 mm
2
Esotec / Esotar Series
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Esotec crossovers
X 252
2200 Hz
4 Ω
X 362
900 Hz / 3500 Hz
4 Ω
Crossover frequencies
Nominal impedance
Power handling
• MW 152
100 W
120 W
150 W
–
–
200 W
200 W
200 W
• MW 162/162 GT
• MW 172
• MW 182
Dimensions
Net weight
38 x 84 x 145 mm
0.33 kg
43 x 104 x 175 mm
0.60 kg
2
6
Esotec / Esotar Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Installation dimensions
Tweeters/Midrange
MD 102
MD 142
Esotar2 110
1
1
1
2
2
5
6
4
6
5
4
5
3
4
3
3
2
1
2
3
max. Ø 62.2 mm
max. Ø 121 mm
Ø 111 mm
6 holes: Ø 4.3 mm on Ø 101 mm
Mounting hole Ø 86 mm
Mounting hole: Ø 52.1 – 55.5 mm
29.1 mm
3 holes: Ø 4 mm on Ø 110.9 mm
Mounting hole Ø 96 mm
(add cut-outs for terminals)
4
5
6
3 mm
13.86 mm
–
max. 37.5 mm
7.5 mm
27 mm
max. 4.5 mm
max. 16 mm
max. 30 mm
2
Esotec / Esotar Series
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Woofers Esotec
MW 152
MW 162
MW 162 GT
MW 172
MW 182
1
2
1
4
1
3
1
2
1
4
2
2
2
7
7
7
7
7
3
3
6
6
6
6
6
3
5
5
5
5
5
4
3
4
4
1
2
max. Ø 145.5 mm
max. Ø 175 mm
max. Ø 166 mm
max. Ø 200 mm
max. Ø 239 mm
6 holes: Ø 4.3 mm
on Ø 134.5 mm
6 holes: Ø 4.3 mm
on Ø 158 mm
4 holes: Ø 7.5 mm
on Ø 155 mm
6 holes: Ø 4.2 mm
on Ø 185.75 mm
6 holes: Ø 4.5 mm
on Ø 219 mm
3
4
3 mm
3 mm
Ø 88 mm
4.2 mm
Ø 113 mm
Mounting hole
min. Ø 124.5 mm
Mounting hole
min. Ø 136 mm
Baffle hole
min. Ø 134 mm
Mounting hole
min. Ø 172 mm
Mounting hole
min. Ø 195 mm
5
6
7
63 mm
4.3 mm
13 mm
67 mm
5 mm
62 mm
1.5 mm
15 mm
77.9 mm
5.4 mm
17 mm
75 mm
5.9 mm
16 mm
15 mm
(at max. cone excursion) (at max. cone excursion) (at max. cone excursion) (at max. cone excursion) (at max. cone excursion)
2
Esotec / Esotar Series
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
2
Woofers Esotar
Esotar2 650
Esotar2 1200
1
2
1
2
6
6
5
5
4
4
3
3
1
2
Ø 169 mm
Ø 297 mm
6 holes: Ø 4.3 mm
on Ø 158 mm
8 holes: Ø 5.3 mm
on Ø 285 mm
3
Mounting hole
min. Ø 136 mm
Mounting hole
min. Ø 260 mm
4
5
6
67 mm
max. 5.2 mm
15 mm
143 mm
max. 7.5 mm
35.5 mm
(at max. cone excursion)
(at max. cone excursion)
2
Esotec / Esotar Series
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Impedance correction circuits
Tweeters/Midrange
C
MD 102
MD 142
Esotar2 110
R
C
R
1.2 µF
1.2 µF
1.2 µF
8.2 Ω
8.2 Ω
8.2 Ω
Woofers
C
MW 152 MW 162 MW 162 GT MW 172 MW 182
Esotar2 650
Esotar2 1200
R
C
R
22 µF
22 µF
22 µF
33 µF
47 µF
22 µF
82 µF
4.7 Ω
4.7 Ω
4.7 Ω
4.7 Ω
4.7 Ω
4.7 Ω
4.7 Ω
2
Esotar crossover recommendations
2
Since the Esotar speakers are meant to use active filtering, Dynaudio recommends following crossover
frequencies:
Esotar2 110
high-pass
-6 dB
Esotar2 650
band-pass
Esotar2 1200
low-pass
-6 dB
Filter type
Slew rate
-6 dB
Cut-off frequency
2000 Hz
100 Hz and 2000 Hz
100 Hz
2
10
Esotec / Esotar Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical specifications
Systems overview
Esotec two-way systems
Bass
Mid
–
High
MD 102
MD 102
MD 102
Crossover
X 252
System 222
MW 152
MW 162
System 242
–
X 252
System 242 GT
MW 162 GT
–
X 252
Esotec three-way systems
Bass
Mid
MD 142
MD 142
High
MD 102
MD 102
Crossover
X 362
System 342
System 362
MW 162
MW 172
X 362
2
Esotar components
Subwoofer
Esotar2 1200
Mid / Bass
High
Crossover 1)
Components
Esotar2 650
Esotar2 110
Active filtering
recommended
1) Please contact your authorized Dynaudio Automotive aftermarket dealer
for further information.
2
Esotec / Esotar Series
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Esotec crossovers
2-way crossover X 252
Terminal label
Connections
1
To power amplifier: + terminal
2
3
4
5
6
7
8
To power amplifier: – terminal
To woofer: + terminal
To woofer: – terminal
To tweeter: + terminal, +2dB
To tweeter: + terminal, ±0dB
To tweeter: + terminal, -2dB
To tweeter: – terminal
2
12
Esotec / Esotar Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Esotec crossovers
1. To connect the woofer
X Connect terminal 3 to the + terminal of the woofer.
X Connect terminal 4 to the – terminal of the woofer.
2. To connect the tweeter
The terminals 5, 6 and 7 offer the ability to fine-tune the sound level. This makes it possible to adjust the level
according to the placement of the speaker in the car and to your personal preference.
X Connect terminal 5 or 6 or 7 to the + terminal of the tweeter:
– just use one of the terminals 5, 6 or 7
– start with terminal 6 for the first setup
– use terminal 5 to increase the sound pressure level by 2 dB
– use terminal 7 to decrease the sound pressure level by 2 dB
X Connect terminal 8 to the – terminal of the tweeter.
3. To connect the power amplifier
X Connect terminal 1 to the + terminal of the power amplifier.
X Connect terminal 2 to the – terminal of the power amplifier.
2
Esotec / Esotar Series
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Esotec crossovers
3-way crossover X 362
Terminal label
Connections
1
2
To woofer: – terminal
To woofer: + terminal
To power amplifier: + terminal
3
To power amplifier: – terminal
To tweeter: – terminal
4
5
6
To tweeter: + terminal, +2dB
To tweeter: + terminal, ±0dB
To tweeter: + terminal, -2dB
7
8
9
To midrange: – terminal
To midrange: + terminal, +2dB
To midrange: + terminal, ±0dB
10 To midrange: + terminal, -2dB
2
14
Esotec / Esotar Series
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting the Esotec crossovers
1. To connect the woofer
X Connect terminal 1 to the – terminal of the woofer.
X Connect terminal 2 to the + terminal of the woofer.
2. To connect the tweeter
The terminals 4, 5 and 6 offer the ability to fine-tune the sound level. This makes it possible to adjust the level
according to the placement of the speaker in the car and to your personal preference.
X Connect terminal 3 to the – terminal of the tweeter.
X Connect terminal 4 or 5 or 6 to the + terminal of the tweeter.
– just use one of the terminals 4, 5 or 6
– start with terminal 5 for the first setup
– use terminal 4 to increase the sound pressure level by 2 dB
– use terminal 6 to decrease the sound pressure level by 2 dB
3. To connect the midrange
The terminals 8, 9 and 10 offer the ability to fine-tune the sound level. This makes it possible to adjust the level
according to the placement of the speaker in the car and to your personal preference.
X Connect terminal 7 to the – terminal of the midrange.
X Connect terminal 8 or 9 or 10 to the + terminal of the midrange.
– just use one of the terminals 8, 9 or 10
– start with terminal 9 for the first setup
– use terminal 8 to increase the sound pressure level by 2 dB
– use terminal 10 to decrease the sound pressure level by 2 dB
4. To connect the power amplifier
X Connect terminal 2 to the + terminal of the power amplifier.
X Connect terminal 3 to the – terminal of the power amplifier.
2
Esotec / Esotar Series
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dynaudio A/S, 8660 Skanderborg, Denmark
Sales & Marketing
Dynaudio International GmbH, Ohepark 2, 21224 Rosengarten, Germany, Phone +49 - 4108 - 4180 - 0
© Dynaudio International GmbH, Esotec/Esotar2 Manual 0208, Item Nr. 455616. All text and image copyrights reserved. Subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
|