A 0977A
Learning Jumbo Remote
Operating Instructions
Congratulations on purchasing the A 0977A 4 in 1Jumbo remote control. The unit can
program a range of devices including TVs, Set top boxes, DVDs, amplifiers, VCRs, PVRs,
CDs, etc. For the full range of compatible devices refer to the device code listing enclosed
with this product.
The remote control has 4 labelled device keys. These are TV, STB (Set top box), DVD and
AUX (Auxiliary). However, any type of device can be programmed into any button.
Instructions
Install batteries in unit (batteries not supplied - requires 2 x AA cells).
The battery compartment is on the rear of the unit. Insert batteries in direction indicated in
battery compartment.
Code Programming
The unit can be programmed in the following ways.
A. Inputting the brand code number.
1. Press and hold the device key button you want to program (eg TV, STB etc) for 3 seconds
until the LED indicator remains illuminated.
2. Release the device key.
3. Locate the brand code number from the code list supplied separately with this unit. Eg.
Akai 0043, 0067, 0070 etc. Now input this code. Once entered the LED will turn off.
4. If you input an incorrect code the LED indicator will flash twice. If this occurs simply go
back to step 1.
5. Test the operation of the remote control. If the first code for the designated appliance (eg
Akai 0043) does not work, or some functions do not work correctly, enter the next
appliance code (eg Akai 0067) until you are successful.
The device key code number can be checked as follows:
1.Press and hold the device key name you want to display (eg TV).
2.The LED indicator will flash once.
3.Whilst holding the device key, press the OK button, then release both buttons.
4.The LED indicator will now flash the number of times that corresponds to each digit of the
code, with a 1 second pause between each digit.
5.For example, if the code is 1038, the indicator will flash once, stop for 1 second, flash 10
times for the “0”, pause for a second, flash 3 times for the “3”, then flash 8 times for the
“8”.
6.When finished, the remote control will exit automatically.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY
1
TV
SAT
DVD
VCR
AUX
DENON
SONY
KENWOOD
SONY
SONY
ONKYO
DENON
KENWOOD
PANASONIC
HITACHI
PANASONIC
HITACHI
PANASONIC
HITACHI
PANASONIC
HITACHI
PANASONIC
HITACHI
2
NEC
TOSHIBA
PIONEER
NEC
TOsHIBA
PIONEER
NEC
TOSHIBA
PIONEER
NEC
TOSHIBA
PIONEER
NEC
TOSHIBA
PIONEER
3
SHARP
SANYO
SHARP
SANYO
SHARP
SANYO
SHARP
SANYO
SHARP
SANYO
4
MITSUBISHI
MITSUBISHI
MITSUBISHI
MITSUBISHI
MITSUBISHI
JVC
AKAI
JVC
AKAI
JVC
AKAI
JVC
AKAI
JVC
AKAI
5
FUJITSU
FUJITSU
SAMSUNG
LG
SAMSUNG
LG
SAMSUNG
LG
SAMSUNG
LG
SAMSUNG
LG
6
DAEWOO
DAEWOO
DAEWOO
DAEWOO
DAEWOO
PHILIPS
THOMSON
EMRSON
LOEWE
PHILIPS
THOMSON
PHILIPS
THOMSON
EMRSON
LOEWE
PHILIPS
THOMSON
EMRSON
LOEWE
PHILIPS
TEAC
7
GE
TEAC
JERROLD
TEAC
APEX
TEAC
GE
TEC
8
NAD
MARANTZ
NAD
MARANTZ
GENERAL
NAD
9
MAGNAVOX
MARANTZ
GENERAL
MARANTZ
MARANTZ
TECHNICS
10
11
TECHNICS
FISHER
ECHOSTAR
TECHNICS
FISHER
TECHNICS
FISHER
ECHOSTAR
YAMAHA
SYLVANIA
YAMAHA
SYLVANIA
Figure 1: This table shows the number (left column) corresponding to different
popular device brands.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
E. Using TV quick search (For TV programming).
1. Press TV device key and release.
2. Turn on TV using your existing remote.
3. Press and hold “MUTE” button. After 3 seconds it will begin searching. Every second it
will send 15 codes to the TV. The LED indicator will flash fast indicating it is sending the
codes.
4. When the TV displays MUTE , release the mute button. The LED indicator will now flash
twice every 2 seconds.
5. When the TV displays “VOL” quickly press the “OK” button to save the code. The LED
indicator will extinguish.
Note 1.
Every quick search will begin from the last code sent until it has completed one circle of
codes.
F. Using LEARNING mode to program the remote control.
1.Press and hold the device key. The LED indicator will flash once. Press and hold the
LEARN key for 3 seconds. The LED indicator will flash continuously.
2. Release the LEARN button.
3. Place the original remote and the A 0977A remote control as per the diagram below with
a distance apart of 1- 2cm
Original Remote
Jumbo Learning Remote
1-2cm
4. Press once the function button you want to learn on the A 0977A universal remote. The
LED indicator will illuminate and remain lit. Press and hold the original remote function
button you want to program. The LED will now remain constantly on.
Press and hold the button on your original remote that you want to learn. The LED will
flash twice and then change to flashing very quickly. The button has now been learnt.
Release the button on your original remote.
If the remote control codes data from your original remote has not been successfully
learnt the LED indicator will blink 3 times and remain constantly lit waiting for data to be
received again from your original remote. To learn the function, please repeat step 4.
5. To learn other buttons, repeat step 4 until you have completed all buttons.
6. Press LEARN key again to quit learning mode.
NOTE 1.
When you enter Learning mode, if you do not press any button within 15 seconds the unit
will exit learning mode.
NOTE 2.
If you are in Learning mode, and no remote control codes data from another remote control
4
Download from Www.Somanuals.com. All Manuals Search And Download.
are received within 15 seconds, the unit will exit learning mode.
NOTE 3.
Except LEARN and device buttons, any button can be programmed, and programmed more
than once. The unit will retain the last code programmed.
To delete any programmed buttons
1.Press the device key.
2.Press and hold the learn button, then press the device button you wish to clear. After 2
seconds. The LED indicator will flash 3 times signifying the data has been deleted.
To delete all the data in a device key
Press and hold the Learn button, then press MUTE button. After 2 seconds, the LED
indicator will flash 3 times and all the learned data will be deleted.
To reset the remote
Go into code programming mode (see ‘A. Inputting the brand code number’). When in
programming mode input the device key 9901. The LED indicator will flash twice and the
remote will go back to its original factory preset.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
|