ImagePro 8758/8772
USER'S GUIDE
Download from Www.Somanuals.com. All Manuals Search And Download.
Declaration of Conform ity
Canada
Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon
97070 USA
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
Agency Approvals
UL, CUL, TUV, GOST
Other specific Country Approvals may apply, please see product certification label.
EMC Directive 89/336/EEC, Amended by 93/68/EEC
EMC: EN 55022
This user’s guide applies to models LP540, LP640, GEN200, and GEN201.
InFocus reserves the right to alter product offerings and specifications at any time.
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 2000
December, 2003
Tradem arks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or regis-
tered trademarks of Adobe Systems Incorporated. InFocus, ProjectorNet, LiteShow,
and LP are trademarks or registered trademarks of InFocus Corporation.
FCC W arning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is oper-
ated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruc-
tion manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
EN 55022 W arning
This is a Class A product. In a domestic environment it may cause radio interference,
in which case the user may be required to take adequate measures. The typical use is
in a conference room, meeting room or auditorium.
Download from Www.Somanuals.com. All Manuals Search And Download.
2
If you are experienced in setting up presentation systems, use the included
Quick Set Up card. For complete details on connecting and operating the
projector, refer to this User’s Guide. Electronic versions of this User’s Guide
Table of Contents
Introduction
Connecting a computer
5
Displaying a computer image
Adjusting the image
Connecting a video device
Displaying a video image
Shutting down the projector
Troubleshooting your setup
10
13
16
Using the keypad buttons
Using the remote control
Using the audio
25
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
27
28
Using the menus
Picture menu
29
33
Settings menu
Maintenance
37
37
38
40
Cleaning the lens
Cleaning the dust filter
Using the security lock
Appendix
41
41
42
42
Accessories
Red LED behavior and projector errors
Projected image size
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Im portant Operating Considerations for Safety
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
Do not place objects or people in the 2 foot (.6m) area along the side of the projector.
For ceiling mount applications, this area should be 5 feet (1.5m).
•
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
co
m
R
pu
te
r
1
S
-v
id
eo
1
m
on
ito
•
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
i
r
o
ut
ne
tw
or
k
co
m
pu
te
se
ria
r
in
l
c
on
tro
l
i
vid
eo
2
vid
eo
in
•
•
Use only InFocus-approved ceiling mounts.
2 ft (.6m)
Use only the power cord provided. A surge-protected power strip is
recommended.
•
•
Refer to this manual for proper startup and shutdown procedures.
In the unlikely event of the lamp rupturing, discard any edible items
placed in the surrounding area and thoroughly clean the area along all
sides of the projector. Wash hands after cleaning the area and handling
the ruptured lamp. This product has a lamp which contains a very
small amount of mercury. Dispose of it as required by local, state or fed-
eral ordinances and regulations. For more information see
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty section at
the end of this user's guide.
5 ft (1.5m)
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Projector com ponents and features
Introduction
keypad
Your new digital projector provides computer and video inputs and has
XGA 1024x768 resolution. The projector is easy to connect, easy to use, easy
to maintain. An Interactive Display on the top of the projector gives you
constant feedback on the status of the projector.
speakers
Online Registration
Register your projector on our website to receive product updates,
announcements, and registration incentives. See the inside of the back cover
for the web address.
Included item s
zoom
focus
elevator foot release
remote
control
receiver (IR)
carry case
Interactive display
connectors
projector
o
c
R
o
m
p
u
te
S
-v
id
r
1
e
o
1
m
o
n
ito
i
r
heat vent
u
n
e
t
tw
remote
o
rk
c
o
m
p
u
s
e
te
ria
r
in
l
lens cap
c
o
n
tro
l
documentation
vid
e
o
2
v
id
e
o
in
lens cap tether*
leveling
foot
audio/video cable
power
cable
computer
cable
audio cable
*The lens cap tether ships in the Documentation Pack. Attach it to the lens cap and
the projector if desired.
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Connector panel of 8772
Connector Panel
The 8758 provides one computer and two video connectors:
external
speaker
(audio out)
•
•
•
one M1-D/A (HD, DVI, and computer)
one S-video
M1-D/A
computer
s-video
monitor
audio
RS232 serial control
one composite RCA
S-video 1
R
serial control
It also has an RS-232 serial connector for serial control. The Command Line
Interface (CLI) specifications and commands are on our website.
video 2
video in
lock
composite
video
computer
audio
power
connector
The 8758 has an additional VESA computer input (HD, HD component,
and computer) and an RJ-45 connector for networked control via
ProjectorNet software.
Connector panel of 8758
external
speaker
(audio out)
M1-D/A
computer
RJ-45
s-video
audio
RS232 serial control
VESA computer
W ireless Projection
S-video 1
You can use the projector’s M1 connector along with the wireless
adapter and software for cable-free digital projection.
Contact an authorized Dukane dealer or visit the website listed on the back
inside cover of this User’s Guide for more information.
R
computer 1
monitor out
serial control
network
video 2
computer in
video in
lock
composite
video
computer
audio
power
connector
monitor
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Connecting a com puter
connect computer cable
R
S-video
1
comr
1
Required com puter connections
serial control
network
video
2
i
monitor out
computer
video in
Connect the black end of the computer cable to the to the Com puter 1 con-
nector on the projector. Connect the blue end to the video port on your com-
puter. If you are using a desktop computer, you first need to disconnect the
monitor cable from the computer’s video port.
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
connect power cable
R
S-video
1
computer
1
uo u
aii
t
serial control
network
video
2
monitor out
computer in
video in
The Power LED on the projector’s keypad turns solid green.
NOTE: Always use the power cable that shipped with the projector.
O ptional com puter connections
connect computer cable
R
S-video
1
computer
1
i
serial control
network
To advance slides in a PowerPoint™ presentation using the remote, plug the
USB connector on the computer cable into the USB mouse connector on
your computer. USB drivers must be installed to use the USB feature. For
more information, see page 11.
i
video
2
monitor out
computer in
video in
To have sound with your presentation, connect the audio cable to your com-
puter and to the computer Audio In connector on the projector.
connect audio cable
R
S-video
1
computer
1
i
serial control
network
di
video
2
montoout
computer in
video in
If you are using a desktop computer and want to see the image on your
computer screen as well as on the projection screen, plug the monitor cable
to the black Monitor Out connector on the projector.
connect monitor cable
R
S-video
1
computer
1
serial control
network
ii
video
2
monitor out
computer in
video in
Download from Www.Somanuals.com. All Manuals Search And Download.
7
If you prefer connecting your LP640 to your computer with an optional
VESA cable, connect one end of the cable to the VESA port on your com-
puter, and connect the other end of the cable to the blue Com puter 2 con-
nector on the projector.
connect VESA cable
R
S-video
1
computer
1
r
serial control
network
video
2
i
i
computer in
video in
You can control the projector from an LCD control panel or computer by
connecting an RS-232 cable to the projector’s Serial connector. Specific
RS-232 commands can be found in the Service and Support section of our
website.
connect RS-232 cable
R
S-video
1
computer
1
serial control
network
video
2
i
monitor out
computer in
video in
The 8758 can be managed by ProjectorNet networking software through
its Network connector.
connect network cable
R
S-video
1
Contact an authorized dealer or visit our website for information on
ProjectorNet.
computer
1
a
i
serial control
network
video
2
monitor out
Network
computer in
video in
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Displaying a com puter im age
remove lens cap
Remove the lens cap.
Press the Power button on the top of the projector or the remote.
press Power button
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness. The Interactive Display on
the projector indicates the startup status.
? No startup screen? Get help on page 17.
turn on computer
Turn on your computer.
The computer’s image should appear on the projection screen. If it doesn’t,
press the Com puter button on the projector’s keypad.
activate laptop’s external port
Make sure your laptop’s external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F5 is used to
turn the external display on and off. Refer to your computer’s documenta-
tion to learn your computer’s key combination.
? No com puter im age? Try pressing the Auto Im age
button on the keypad. Get help on page 17.
Download from Www.Somanuals.com. All Manuals Search And Download.
9
a
First-tim e projector use with W indows 98
The first time you connect a computer running Windows 98 to the projector,
the computer recognizes the projector as “new hardware” and the Add
New Hardware Wizard appears. Follow these instructions to use the Wiz-
ard to load the correct driver (which was installed with your Windows
operating system).
If you are running Windows 2000, Windows ME, or Window XP, skip these
steps and go to “Adjusting the image” on page 12.
b
a Click Next to begin searching for the driver.
b Make sure “Search for the best driver” is selected, then click Next.
c
c Uncheck any checked boxes, then click Next. Windows automatically
locates the driver. If this driver has been removed, reload the driver using
your Windows operating system CD.
d
d When Windows finds the driver, you are ready to install it. Click Next.
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Skip this page if you did not connect the USB portion of the M1 com -
puter cable
For W indows 98:
•
If you connected the USB cable, the Add New Hardware Wizard
appears again. Drivers must be installed to use the USB functionality.
•
The W izard launches two tim es.
The first time it detects a USB Human Interface Device (for the key-
board).
The second time it detects a USB Human Interface Device (for the
mouse).
For W indows 2000, W indows ME, and W indows XP:
The USB drivers are automatically installed.
•
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Adjusting the im age
release button
adjust height
Adjust the height of the projector, if necessary, by pressing the release but-
ton to extend the elevator foot.
t
a
i
t
co
R
m
pu
te
S
-v
r
1
id
eo
1
m
on
ito
a
in
r
o
ut
ne
tw
ork
rotate
leveling
foot
co
m
pu
se
ria
te
r
in
l
c
on
tro
l
vid
vid
eo
2
eo
in
elevator
foot
Rotate the leveling foot (located at the bottom back right corner), if neces-
sary.
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 42 for a table listing screen sizes and distances.
r
uo
o
com
R
pute
S
-vid
r
1
eo
1
mo
i
ui
i
ut
netw
ork
com
pute
seri
al co
r
in
ntro
l
vid
eo
2
vide
o
in
Adjust the zoom or focus rings by rotating them until the desired image size
and focus are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the vertical digital keystone by using the
buttons on the keypad.
adjust keystone
set the projector to automatically adjust the vertical keystone. See page 30.
pt
ao
com
R
put
er
1
S-v
ideo
1
mo
nito
r
ou
i
et
wo
t
com
put
ser
er
i
ial
n
c
ont
rol
u
vide
vide
o
2
o
in
adjust Contrast or Brightness
Adjust the Contrast or Brightness in the Picture menu.
See page 29 for help with the menus.
contrast
brightness
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Connecting a video device
S-video
1
R
connect A/V cable
computer
1
t
serial control
network
Standard video connections
video
2
monitor out
computer in
video in
Plug the audio/video (A/V) cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the yel-
low Video 2 connector on the projector.
Plug a white connector into the left audio out connector on the video device
and plug a red connector into the right audio out connector on the video
device. Plug the remaining white connector into the left audio in connector
on the projector, and plug the red connector into the right audio in connec-
tor on the projector.
connect power cable
Connect the black power cable to the connector on the back of the projector
and to your electrical outlet.
R
S-video
1
computer
1
ii
t
serial control
network
video
2
monitor out
computer in
video in
NOTE: Always use the power cable that shipped with the projector.
R
S-video
1
connect S-video and video cables
O ptional video connections
computer
1
u
serial control
network
i
video
2
monitor out
computer in
video in
If the video device uses a round, four-prong S-video connector, plug an
S-video cable (sold separately) into the S-video connector on the video
device and into the S-Video 1 connector on the projector. Use the A/V
cable’s audio connectors as described directly above (the yellow connectors
on the A/V cable are not used).
To connect a progressive scan EdTV or HD source, use the Component to
M1 adapter (sold separately).
Download from Www.Somanuals.com. All Manuals Search And Download.
13
Displaying a video im age
remove lens cap
Remove the lens cap.
press Power button
Press the Power button on the top of the projector or the remote.
The LED flashes green and the fans start to run. When the lamp comes on,
the startup screen is displayed and the LED is steady green. It can take a
minute for the image to achieve full brightness. The Interactive Display on
the projector indicates the startup status.
? No startup screen? Get help on page 16.
Plug in and turn on the video device.
turn on video device
The video device’s image should appear on the projection screen. If it
doesn’t, press the Video button on the keypad.
Adjust the height of the projector by pressing the release button to extend
the elevator foot. Rotate the leveling foot, if necessary.
release button
adjust height
do
u
co
R
m
pu
te
S
-v
r
1
id
eo
1
m
on
ito
u
o i
r
o
ut
ne
tw
ork
rotate
leveling
foot
co
m
pu
se
ria
te
r
in
l
c
on
tro
l
vid
vide
o
2
eo
in
elevator
foot
adjust distance
Position the projector the desired distance from the screen at a 90 degree
angle to the screen. See page 42 for a table listing screen sizes and distances
to the screen.
ad
u
com
R
pute
S
-vid
r
1
eo
1
n
itor
audo
n
out
netw
ork
com
pute
seri
al co
r
in
ntro
l
ud
i
vi
deo
2
vide
o
in
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Adjust the zoom or focus rings by rotating them until the desired image size
and focus are produced.
adjust zoom and focus
zoom
focus
If the image is not square, adjust the vertical keystone using the buttons on
the keypad.
adjust keystone
Press the upper Keystone button to reduce the upper part of the image, and
press the lower Keystone button to reduce the lower part.
You can also adjust the horizontal keystone on the 8758 via the menus, or
set the projector to automatically adjust the vertical keystone. See page 30.
ue
u
o
com
R
put
er
1
S-v
ideo
ideo
1
mon
it
au
i
u
t
wor
k
com
put
seri
al
er
i
n
c
ont
rol
d
v
in
2
vide
o
adjust volume
Adjust the volume on the keypad or remote.
i
co
R
m
pu
te
r
S
-v
1
id
eo
1
m
on
ito
i
r
ou
ne
tw
t
or
k
co
m
pu
se
ria
te
r
in
l
c
on
tr
ol
i
vi
vid
eo
2
de
o
in
adjust Picture menu
Adjust the Contrast, Brightness, Color, or Tint in the Picture menu.
See page 29 for help with the menus.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Troubleshooting your setup
The projector automatically blanks the screen after no active source is
detected for 30 minutes. This blank screen helps preserve the life of the pro-
jector. The image returns when an active source is detected or a remote or
keypad button is pressed. The Interactive Display on the projector indicates
the shutdown status.
If your image appears correctly on the screen, skip to the next section
(page 25). If it does not, troubleshoot the setup. The Interactive Display and
LED on top of the projector indicate the state of the projector and can help
you troubleshoot.
Screen Save
Table 1: LED behavior and m eaning
You can make the blank screen appear after five minutes by turning on
utes with five minute intervals.
LED color/behavior
Meaning
solid green
The projector is plugged in, or the projec-
tor has been powered on and the soft-
ware has initialized. The projector has
been turned off and the fans have stopped.
Power Save
The projector also has a Power Save feature that automatically turns the
lamp off after no signals are detected for 5 minutes. After 3 additional min-
utes with no signal, the projector powers down. If an active signal is
received before the projector powers down, the image is displayed. You
must press the Power button to display an image after 30 minutes have
passed. When Power Save is enabled, Screen Save is disabled. See page 33.
blinking green
The power button has been pressed and
the software is initializing, or the projec-
tor is powering down and the fans are
running to cool the lamp.
blinking red
A fan or lamp failure has occurred. Make
sure the vents aren’t blocked (see
page 22). Turn off the projector and wait
one minute, then turn the projector on
again. If the Replace Lamp message
appears, replace the lamp and reset the
lamp timer. Contact Technical Support if
the problem persists.
Turning off the projector
see page 42 for more information
To turn off the projector, press the Power button and verify that you want to
turn the projector off by pressing the Power button again within 3 seconds.
You can cancel the shutdown by not pressing the Power button a second
time. The lamp turns off and the LED blinks green for 1 minute while the
fans continue to run to cool the lamp. When the lamp has cooled, the LED
lights green and the fans stop. Unplug the power cable to completely power
off the projector.
solid red
An unidentifiable error: please contact
Technical Support.
The following tables show common problems. In some cases, more than one
possible solution is provided. Try the solutions in the order they are pre-
sented. When the problem is solved, you can skip the additional solutions.
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Source Troubleshooting
Problem
Solution
Result
Plug power cable in, press Power button.
Rem ove lens cap.
Correct im age
No startup screen
co
m
R
pu
te
r
S
-v
id
eo
1
1
m
on
ito
r
i
ou
t
ne
tw
or
k
co
m
pu
te
se
ria
r
in
l
c
on
tr
ol
vid
eo
2
vid
eo
a
in
i
c
R
o
mp
u
te
r
1
S
-v
id
a
eo
1
i
co
R
m
mo
n
ito
pu
te
r
S
i
-v
r
o
ut
i
1
id
ne
tw
eo
1
ork
m
on
ito
ii
r
o
ut
ne
tw
or
k
co
m
pu
se
ria
te
r
in
l
c
on
tro
l
co
m
vid
vid
e
pu
se
o
te
ria
l
2
r
in
c
on
tro
l
a
vid
vid
eo in
eo
2
eo
in
Com puter im age projected
Only startup screen appears
Press the Com puter button
Activate laptop’s external port
A
A
A
or restart
laptop
i
co
R
m
pu
te
S
-v
ide
r
1
o
1
m
on
ito
i
r
o
ut
ne
tw
or
k
do
u
c
om
pu
se
rial
R
te
r
in
con
tr
ol
te
S
-v
id
eo
r
1
i
1
v
id
eo
2
m
on
ito
d
r
o
ut
ne
v
ide
tw
or
o
k
in
co
m
pu
se
ria
te
r
i
l
n
c
on
tro
l
v
vid
id
eo
2
eo
in
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Adjust com puter refresh rate in Control
Panel>Display>Settings>Advanced>
Adapter (location varies by operating
system )
Com puter im age projected
No com puter im age, just the words “Signal out of
range”
Signal
range
out
of
A
A
A
A
r
a
o o
a
u
co
mpu
R
co
R
mp
ute
ter
S-
vid
eo
1
r
1
S
-vi
de
1
o
1
mo
nito
mo
nit
o
a
o
a
r
o
ou
ne
tw
ork
o
rk
t
co
mpu
co
mp
se
ria
ter
ute
se
ria
in
l
c
ont
ro
r
in
l
c
on
tro
l
l
i
i
v
ide
vid
eo
o
2
2
vid
eo in
vid
eo
in
You m ay also need to set a different
resolution on your com puter, as shown
in the following problem , “Im age fuzzy
or cropped”
The video em bedded in my PowerPoint
presentation does not play on the screen
Turn off the internal LCD display on your
laptop
Em bedded video plays correctly
A
A
B
B
r
u
a
o
t
u
co
mp
ute
R
co
mp
ute
R
1
S
-vi
de
r
1
S
-vi
de
1
o
1
o
mo
nit
or
mo
nit
or
u
a
o
u
t
ne
tw
ork
u
t
ne
tw
ork
co
mp
co
mp
ute
se
ria
ute
in
se
rial
r
in
l
r
c
on
c
on
tro
tro
l
l
a
i
i
vid
eo
vid
eo
2
2
vid
eo
vid
eo
in
in
Download from Www.Somanuals.com. All Manuals Search And Download.
18
the native resolution of the projector
(Start>Settings>Control
Im age clear and not cropped
Im age fuzzy or cropped
A
Panel>Display>Settings tab, select
1024x768)
A
A
For a laptop,
disable laptop
m onitor
or turn-on dual-
display m ode
Connect USB cable (page 7) then load USB
drivers, if needed (page 10).
Rem ote advances slides
See page 25 for inform ation on the rem ote
Rem ote control not advancing PowerPoint slides
R
S-video
1
computer
1
serial control
network
video
2
i
monitor out
computer
video in
X
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Projector troubleshooting
Problem
Solution
Result
Square im age
Im age not square
Adjust keystone on keypad or Picture m enu
u
e
d
u
o
com
R
put
er
1
S-v
ideo
1
mo
nito
u
i
nt
o
k
com
put
ser
ial
er
i
n
c
ont
rol
ad
o
n
vi
deo
2
vide
o
in
Correct im age
Adjust the focus lens or Sharpness in the
Picture>Advanced m enu
Im age not sharp
A B
A B
Change aspect ratio to 16:9 in
Picture>Aspect ratio m enu
Correct im age
Im age does not fit 16:9 screen
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Turn off Ceiling in Settings>System m enu
Correct im age
Im age upside down
B
A
A B
Turn off Rear in Settings>System m enu
Im age reversed left to right
Correct im age
A
A B
Correct im age
Projected colors don’t m atch source
Adjust color, tint, color tem perature,
brightness, contrast in the m enus
COLOR
COLOR
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Make sure vents aren’t blocked; allow
projector to cool for one m inute
Unplug projector; wait one m inute; plug in
projector and turn it on: lam p lights
Lam p won’t turn on, LED blinking red (page 16)
blinks
red
co
R
m
p
u
te
S
-v
id
r
1
e
o
1
m
o
n
ito
r
o
n
e
u
t
tw
o
rk
co
m
i
o
p
u
s
e
te
ria
l
r
in
co
R
c
o
m
ntro
l
pu
te
S
r
1
-v
id
eo
1
i
vid
vid
e
m
o
on
2
ito
r
a
ii
o
ut
ne
tw
ork
e
o
in
i
o
co
m
c
om
p
ute
R
pu
se
te
ria
l
r
in
c
on
r
S-v
id
1
tro
l
e
o
1
vid
vid
eo
mo
nito
2
a
ii
r
o
ut
ne
tw
ork
eo
in
co
m
pu
se
ria
te
r
in
l
c
on
tro
l
vid
vid
eo
2
eo
in
Lam p turns on
blinks
red
a
i
co
R
co
R
m
m
pu
pu
te
S
te
S
-v
r
1
-v
r
1
id
id
eo
eo
1
1
m
m
on
on
ito
do
ito
r
ii
r
o
n
o
ut
ut
ne
ne
tw
tw
ork
ork
co
co
m
pu
m
pu
se
s
er
te
ria
te
r
in
l
r
in
ial
con
c
on
tro
l
tro
l
vid
vid
eo
vid
vid
eo
2
2
eo
eo
in
in
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Correct im age
Move projector, adjust zoom , adjust height
Im age not centered on screen
zoom
t
com
R
pu
ter
S-
vid
1
eo
1
mo
nt
r
o
ne
two
ut
rk
com
pu
seria
l
co
ter
in
ntro
l
vid
vid
eo
2
eo
in
Adjust horizontal or vertical position in
Picture>Advanced m enu
i
co
R
m
pu
te
S
-v
r
1
id
eo
1
t
m
on
it
i
or
ou
t
n
et
t
w
or
k
co
m
R
pu
te
r
1
S
-v
id
eo
1
m
on
ito
i
c
om
r
o
ut
ne
tw
or
p
ut
se
ria
er
k
in
l
co
nt
ro
l
v
id
eo
co
m
2
pu
te
se
ria
r
in
l
c
on
tro
l
v
id
eo
in
vid
eo
2
vid
eo
in
Still having problem s?
If you need assistance, visit our website or call us. See the inside of the back
cover for a list of all contact numbers and relevant web addresses.
This product is backed by a limited two-year warranty. An extended war-
ranty plan may be purchased from your dealer. When sending the projector
in for repair, we recommend shipping the unit in its original packing mate-
rial, or having a professional packaging company pack the unit. Please
insure your shipment for its full value.
Download from Www.Somanuals.com. All Manuals Search And Download.
23
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an over-
view of their functions:
m enu–opens the on-screen menus (page 29).
select–confirms choices made in the menus (page 29).
page 30.
volum e–adjusts sound (page 26).
menu navigation buttons
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Using the rem ote control
The remote uses two (2) provided AA batteries. They are easily installed by
sliding the cover off the remote’s back, aligning the + and - ends of the bat-
next button
previous button
Previous and Next buttons allow you to navigate through your PowerPoint
presentation while in Slide Show mode. Connect the USB connector on the
computer cable to your computer to use these buttons. When you do this for
the first time, the Add New Hardware wizard may appear. See page 10 for
details on loading the correct USB drivers.
navigation
buttons
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 29 for more info on the menus.
and Video and Com puter buttons to switch between sources.
Troubleshooting the rem ote
•
Make sure the batteries are installed in the proper orientation and are
not dead. The LED at the top of the remote lights when any button is
pressed when the battery power is adequate.
Two presentation-specific features are also provided. Use the Blank button
to display a blank screen instead of the current slide (you can choose which
color is displayed, see page 34); use the Effect button to invoke a user-defin-
able action, such as freeze or zoom (see page 35 to learn to program this but-
ton).
•
•
Make sure you’re pointing the remote at the projector, not the com-
puter, and are within the remote range of 30 feet (9.14m).
If you are trying to advance PowerPoint slides, make sure the USB
cable is connected. If using a USB cable, make sure the correct drivers
are installed.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Using the audio
connect audio cable
To play sound from the projector, connect your source to the Audio In con-
nector on the projector.
R
S-video
1
computer
1
serial control
network
video
2
monitor out
computer in
video in
To adjust the volume, use the buttons on the keypad or remote.
To adjust the balance or turn off the projector’s chime, use the Audio menu
(see page 33).
To mute the sound, press the Mute button.
adjust volume
Troubleshooting audio
If there is no sound, check the following:
co
R
m
pu
te
S
-v
id
r
1
eo
1
m
on
ito
r
i
ou
ne
tw
t
or
k
•
•
•
Make sure the audio cable is connected.
Make sure mute isn’t active.
co
m
pu
se
ria
te
r
in
l
c
on
tr
ol
i
vi
vid
eo
2
de
o
in
Make sure the volume is turned up enough. Press the Volum e button
on the keypad or remote.
•
•
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
Connecting external speakers
connector.
S-video
1
R
computer
1
serial control
network
external speakers
video
2
monitor out
computer in
video in
speaker
cable
Download from Www.Somanuals.com. All Manuals Search And Download.
26
O ptim izing com puter im ages
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For gen-
eral information on using the menus, see page 29.
Several features are provided to make giving presentation easier. The fol-
lowing is an overview, details are found in the menu section on page 29.
•
The remote’s Effect button allows you to assign various features to the
key. The default effect is Freeze. You can select from Blank, Mute,
Aspect Ratio, Source, Auto Image, Freeze, Zoom, About, PiP, and Mask.
See page 35 for details.
•
•
•
•
Adjust the Keystone, Contrast, or Brightness in the Picture menu.
Change the Aspect Ratio. See page 30 for details.
Adjust the Color Temperature in the Advanced menu.
•
The Freeze effect allows you to freeze the displayed image. This is use-
ful if you want to make changes on your computer without your audi-
ence seeing them.
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced menu.
•
•
settings later. See page 31.
•
•
•
•
The Blank button on the remote allows you to display a blank screen
instead of the active source. See page 34.
The PiP effect lets you show a video source in a smaller window on top
of the computer image. See page 35.
if in a bright room (page 31).
The Startup Logo menu option lets you change the default startup
screen to a black, white, or blue screen. See page 34.
Two menu options, Power Save and Screen Save, are provided to auto-
matically shut down the projector after several minutes of inactivity or
display a blank screen. This helps preserve lamp life. See page 33.
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Custom izing the projector
After the video device is connected properly and the image is on the screen,
you can optimize the image using the onscreen menus. For general informa-
tion on using the menus, see page 29.
You can customize the projector for your specific setup and needs. See
page 33 to page 37 for details on these features.
•
•
For rear projection, turn Rear mode on in the Settings>System menu.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Picture
menu. See page 30.
For ceiling mounted projection, turn Ceiling mode on in the Set-
tings>System menu.
•
Change the Aspect ratio. Aspect ratio is the ratio of the image width to
image height. TV screens are usually 1.33:1, also known as 4:3. HDTV
and most DVDs are 1.78:1, or 16:9. Choose the option that best fits your
input source. See page 30.
•
•
Turn on Automatic Vertical Keystone adjustments.
Specify which source the projector checks first for active video during
power-up.
•
•
•
•
•
•
•
Specify the function of the Effect Key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
•
•
Select a Sharpness setting. See page 32.
Adjust the Color Temperature. Select a listed value, or select User and
page 32.
Specify blank screen colors and startup logos.
Specify the menu language.
•
if in a bright room (page 31).
Project wirelessly with wireless adapter. See page 6.
Manage your projector via ProjectorNet software. See page 8 for more
information.
•
Control your projector using RS232 commands. See page 8.
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Using the m enus
Dot
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) The
Main menu appears. Use the arrow buttons to move up and down to high-
light the desired submenu, then press the Select button.
Menu
button
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value, select an option using radio but-
tons, or turn the feature on or off using check boxes. Press Select to confirm
your changes. Use the arrows to navigate to another setting. When your
adjustments are complete, navigate to Exit, then press Select to go to the
previous menu; press the Menu button at any time to close the menus.
Keypad navigation
buttons
Main menu
Dots appear before the menu name. The number of dots indicate the menu’s
level, ranging from one (the Main menu) to four (the most nested menus).
Picture
menu
Dots
The menus are grouped by usage:
•
•
The Picture menu provides image adjustments.
Settings
menu
The Settings menu provides set-up type adjustments that are not
changed often.
•
The About menu provides a read-only display of information about the
projector and source.
Certain menu items may be grayed out until a particular source is con-
nected. For example, Sharpness is only available for video sources and will
be hidden when a computer source is active. Other menu items may be
grayed out when they are not available. For example, Brightness is grayed
out until an image is active.
About menu
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Picture m enu
To adjust the following six settings, highlight the setting, press Select, use
the up and down arrows to adjust the values, then press select to confirm
the changes.
Vertical Keystone
increasing keystone
decreasing keystone
Vertical Keystone: adjusts the image vertically and makes a squarer image.
You can also adjust vertical keystone from the keypad. If you want the pro-
jector to automatically adjust the vertical keystone, check the Auto Vert
check box.
Horizontal Keystone: adjusts the image horizontally and makes a squarer
image. This option is only available on the 8758.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Horizontal Keystone
Brightness: changes the intensity of the image.
Color: (video and component sources only) adjusts a video image from
black and white to fully saturated color.
Tint: (NTSC video sources only) adjusts the red-green color balance in the
image.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 1.33:1, also known as 4:3. HDTV and most DVDs are
1.78:1, or 16:9. The default is 4:3, which displays the input resized up or
down to fill the display area.
Aspect Ratio
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Presets: The provided Presets optimize the projector for displaying com-
puter presentations, photographs, and film images. You can use the preset
as a starting point, then further customize the settings for each source. If
you do change the settings, the Preset menu item selected changes to None
to indicate your customization. The settings you customize are saved in the
preset for each source. To restore the factory default settings, choose Fac-
tory Reset in the Settings>Service menu.
There are also three user-definable presets. To set a preset for the current
source, adjust the image, then choose Save User 1, 2, or 3. You can recall
these settings in the future by selecting the appropriate user presets.
Presets
Room Lighting: This features optimizes the projector for your room’s light-
ing conditions. Select Dark if you are in a dark room, Light if in a bright
room. Choosing Light maximizes the light output from the projector.
Room Lighting
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Advanced settings
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Sharpness
Color Space: This option applies to computer sources. It allows you to
select a color space that has been specifically tuned for the video input.
When Auto is selected, the projector automatically determines the standard.
To choose a different setting, turn off Auto, then choose RGB for computer
sources, choose either SMPTE240, REC709 or REC601 for component
sources.
Color Space
Color Tem perature: changes the intensity of the colors. Select a listed
value, or select User and individually adjust the intensity of the red, green,
and blue colors.
Color Temperature
The following 4 options are for computer and component sources only.
Phase: adjusts the horizontal phase of a computer source.
Tracking: adjusts the vertical scan of a computer source.
Horizontal/Vertical Position: adjusts the position of a computer source.
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Settings m enu
Audio: allows adjustments to the volume and balance, and turns the projec-
tor’s startup Chime on and off.
Sources: allows you to assign a particular input to a specific source key
when using the optional Integrator remote. Also allows selection of a
default Startup Source and enables or disables Autosource.
Audio
Sources>Startup Source: this determines which source the projector
checks first for active video during power-up.
Sources>Autosource: When Autosource is not checked, the projector
defaults to the source selected in Startup Source. If no source is found, a
blank screen displays. When Autosource is checked, Startup Source deter-
mines which source the projector defaults to at power-up. If no signal is
present, the projector checks the sources in order until a source is found or
until power down.
Startup
Source
Sources
System >Rear : reverses the image so you can project from behind a translu-
cent screen.
Ceiling: turns the image upside down for ceiling-mounted projection.
Auto Ceiling: automatically senses when the projector is inverted and turns
the image upside down. This is On by default.
Auto Power: When Auto Power is checked, the projector automatically
goes into the startup state after the projector is powered on. This allows con-
trol of ceiling mounted projectors with a wall power switch.
Screen Save
Display Messages: displays status messages (such as “Searching” or
“Mute”) in the lower-left corner of the screen.
System menu
Power Save: automatically turns the lamp off after no signals are detected
for 5 minutes. After 3 additional minutes with no signal, the projector pow-
ers down. If an active signal is received before the projector powers down,
the image will be displayed.
Screen Save: automatically blanks the screen with a black color after no sig-
nals are detected for a preset number of minutes. The image returns when
an active source is detected or a remote or keypad button is pressed. Screen
Save is disabled when Power Save is enabled.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Startup Logo: allows you to display a blank Black, White, or Blue screen
instead of the default screen at startup and when no source is detected. It
also allows you to capture and display a custom startup screen.
To capture a custom logo, display the image you want to capture on your
computer, highlight Capture New, then press Select twice. While the cap-
ture is underway, the LED on the keypad turns orange. When ready, the
projector confirms the capture and the LED changes to green.
Startup Logo
The next time you start the projector, the custom logo you captured dis-
plays.
Blank Screen: determines what color is displayed when you press the
Blank button on the remote.
Blank Screen
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Effect Key: allows you to assign a different function to the Effect button on
the remote to quickly and easily use the effect. Only one effect can be
enabled at a time. Highlight an effect and press Select to choose a different
one. The default effect is Freeze.
Blank: shows an empty screen.
Mute: turns off all sound.
Effect Key
Aspect Ratio: sets the ratio of the image width to image height.
Source: cycles through the available sources.
Auto Im age: causes computer sources to be reacquired.
Freeze: pauses the projected image.
Zoom : lets you magnify a part of the screen. This feature only works if
you purchase an optional remote control with mouse buttons and cur-
sor control. To use the Zoom effect, press Effect, then press the left
mouse button to zoom the image, press the right mouse decrease the
magnification. You can use the cursor control to pan the image, display-
ing different parts of it (only if the image is magnified). To return to the
original size and cancel Zoom, press the Effect button a second time.
About: displays the About menu.
PiP: (Picture in Picture) allows you to overlay a smaller window show-
ing the video source on top of the larger computer source window. You
must have both a computer and video source connected to use PIP. You
can’t show a computer image in the smaller PiP window, only a video
image. You can select a small, medium, or large window. You can also
move the PiP window on the screen using the PiP Position X and Y
options in the menu. Press the up and down arrows to change the posi-
tion.
Picture in Picture
Mask: allows you to cover part of the image with a black curtain. Press
the up and down arrows to raise or lower the curtain on the image.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Network: The 8772 has an RJ45 Ethernet connector that supports network
connections and TCP/IP protocols. This will allow for the control and man-
agement of the projector over a corporate network. The following fields are
accessible when DHCP is not checked and available for manual entry of
data.
Network
Network
Info
IP Address: Identifies the projector on the network.
Subnet m ask: Separates the network address part of the IP address.
Default gateway: The IP address of the local router.
DHCP: Select this to automatically obtain an IP address, Subnet mask,
and Default gateway.
Network Info: Provides information on the network configuration.
The Network Info menu is informational and cannot be edited. It displays
the current IP Address, Subnet Mask, Default Gateway, and the projector’s
MAC Address.
Language
Language: allows you to select a language for the onscreen display of
menus and messages.
Service: to use these features, highlight them and press Select.
Factory Reset: restores all settings (except Lamp Hours and Network set-
tings) to their default after displaying a confirmation dialog box.
Reset Lam p: resets the lamp hours counter in the About menu to zero. Do
this only after changing the lamp. It displays a confirmation dialog box.
Service menu
Service Info: provides information about the projector’s software version
and the active source.
Service Code: only used by authorized service personnel.
Download from Www.Somanuals.com. All Manuals Search And Download.
36
Maintenance
clean the lens
with a soft dry cloth
and non-abrasive
cleaner
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion. If you
don’t intend to use the projector immediately, replace the lens cap.
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Replacing the projection lam p
The lamp hour timer in the About menu counts the number of hours the
page 41 for information.
About menu
turn off and unplug
the projector
R
S-video
1
computer
1
ii
serial control
network
video
2
monitor out
computer in
video in
2 Wait 60 minutes to allow the projector to cool thoroughly.
wait 60 minutes
loosen the screw on lamp door
pry the lamp door off
3 Turn the projector upside down and remove the lamp door by loosening
the captive screw and then prying the lamp door out.
WARNINGS:
remove the screws on lamp module
•
you replace the lamp.
•
•
•
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass portion of the lamp module. Fingerprints can
obscure projection sharpness.
Download from Www.Somanuals.com. All Manuals Search And Download.
38
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it. Before replacing the lamp, clean the
lamp compartment and dispose of cleaning materials. Wash hands after
lamp replacement. his product has a lamp which contains a very small
amount of mercury. Dispose of it as required by local, state or federal
5 Carefully remove the lamp module by grasping and lifting the metal
bail wire. Dispose of the lamp in an environmentally proper manner.
remove module using bail wire
6 Install the new lamp module, making sure that it is properly seated.
7 Replace the two screws.
8 Replace the lamp door and tighten the screw.
9 Plug in the power cable then press the Power button to turn the projec-
tor back on.
10 Reset the lamp hour timer by navigating to the Settings>Service menu
and selecting Lam p Reset.
reset lamp time in Service menu
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Cleaning the dust filters
R
S-video
1
computer
1
u
serial control
In dirty or dusty environments, the dust filters can become clogged, causing
high temperatures inside the lamp module. These high temperatures can
impact lamp performance and operating life. Routine maintenance to
the filters every 100 hours. Dust filter maintenance may need to occur more
often than 100 hours depending on your installation/use environment.
There are two filters, one mesh filter attached to the dust filter door and one
metal grid filter adjacent to the lamp door.
network
video
2
turn off and unplug
the projector
monitor out
computer in
video in
wait 60 minutes
vacuum filter
remove filter door
1 Turn off the projector and unplug the power cable.
2 Wait 60 minutes to allow the projector to cool thoroughly.
WARNING: To avoid burns, allow the projector to cool for at least 60
minutes before you clean or replace the dust filter.
3 Turn the projector upside down and remove the lamp door. See page 38.
4 Remove the dust filter door.
5 Clean the filter using a vacuum set on low power.
6 Replace the dust filter door and the lamp door.
7 Vacuum the non-removable metal grid filter adjacent to the lamp door.
metal grid filter
S-video
1
R
computer
1
serial control
network
video
2
monitor out
computer in
video in
Using the security lock
The projector has a security lock for use with a cable lock system. See
“Accessories” on page 41 for ordering information. Refer to the information
that came with the lock for instructions on how to use it.
security lock
Download from Www.Somanuals.com. All Manuals Search And Download.
40
Appendix
Optional Accessories
Part Num ber
CA-ATA-019
SP-CEIL-011
Accessories
Shipping Case (ATA approved)
Projector Mount
Standard Accessories
(ship with the projector)
False Ceiling Plate for Projector Mount
SP-LTMT-PLT
SP-LTMT-EXTP
Part Num ber
111-0053-xx
110-0793-xx
SP-DVI-A
Extension Arm for Projector Mount
26” - 47”
Shipping Box (with packaging)
Carry Case
Organizer Carry Case
CA-C230
Computer Cable 6 ft (1.8 m)
Audio/Video Cable 6 ft (1.8 m)
Audio Cable 6 ft (1.8 m)
Power Cable*
DVI-D Cable 6 ft (1.8 m)
SP-DVI-D
516-0051-xx
210-0118-xx
516-0052-xx
590-0728-xx
SP-LAMP-017
M1 to Component Adaptor
LiteShow Wireless Connection
ProjectorNet Software (LP640 only)
Audio/Video Cable, 30 ft (9m)
Projector Cable Lock System
50” Diagonal Screen (portable)
60” Diagonal Screen (portable)
84” Diagonal Wall/Ceiling Mounted Screen
Replacement Lamp Module
SP-M1-ADPT
LP-LITESHOW
SW-PN2-1CD
SP-AV30
Navigator Remote
Projection Lamp Module (included
in projector)
SP-LOCK-B
A650
Lens Cap
340-1234-xx
321-0192-xx
009-0878-xx
010-0497-xx
009-0659-xx
SP-CABLETIES
301130
HW-DLXSCRN
HW-WALLSCR84
SP-LAMP-017
HW-PRESENTER-RF
HW-PRESENTER
HW-CONDUCTOR+
Lens Cap Tether
Quick Setup card
User’s Guide with CD
Safety Card
RF Presenter Remote Control
IR Presenter Remote Control
IR Conductor + Remote Control
Color-coded Cable Ties, 3 set
SCART Adapter*
*country-dependent
NOTE: Use only approved accessories.
Download from Www.Somanuals.com. All Manuals Search And Download.
41
Red LED behavior and projector errors
Projected im age size
Table 3:
Im age sizes
If the projector is not functioning properly and the red LED is blinking, con-
sult Table 2 to determine a possible cause. There are two second pauses
between the blinking cycles. Visit our website for more details on the red
LED error codes. See the inside back cover for contact information.
Minim um
Maxim um
Diagonal
(feet/m )
throw ratio 1.28
Minim um
Maxim um
Distance
Diagonal
Horizontal
Horizontal
to screen
(feet/m )
(feet/m )
throw ratio 1.53
(feet/m )
throw ratio 1.91
(feet/m )
throw ratio 1.60
Table 2:
5/1.5
10/3
3.3/1
6.5/2
4/1.2
2.6/0.8
5.2/1.6
7.8/2.4
10.4/3.2
15.6/4.8
17/5.2
3.2/1
Red LED Behavior
Explanation
7.8/2.4
6.3/1.9
9.3/2.8
12.4/3.8
18.6/5.7
20.3/6.2
One (1) blink
The lamp won't strike after five (5)
attempts. Check the lamp and lamp door
installations for loose connections.
15/4.6
20/6.1
30/9.1
32.8/10
9.8/3
11.7/3.6
15.5/4.7
23.2/7.1
25.4/7.7
13/4
19.5/5.9
21.3/6.5
Two (2) blinks
The lamp counter hours have exceeded
lamp life hours. Replace the lamp and
reset the lamp hours counter.
Three (3) blinks
The projector has shut down the lamp.
Turn the projector off and wait one
minute, then turn the projector on. If the
lamp does not turn on, replace the lamp.
Contact Technical Support for repair if
replacing the lamp does not solve the
problem.
NOTE: Visit our website for an interactive image size calculator.
Four (4) blinks
Five (5) blinks
The fan has failed. Contact Technical Sup-
port for repair.
The projector is overheating. Check for a
blocked air vent. Contact Technical Sup-
port for repair if clearing the air vents
does not solve the problem.
Download from Www.Somanuals.com. All Manuals Search And Download.
42
Num erics
1024x768 resolution 5
custom logo
A
About 35
advancing PowerPoint slides 7
Aspect Ratio 35
audio 26
Audio In connector 7, 13
audio volume 15
Auto Image 35
Auto Power 33
D
B
Blank 35
Blank screen 34
blinking green 16
blinking red 16
Brightness 12
E
C
cables
optional 41
standard 41
F
cleaning the dust filter 40
cleaning the lens 37
Color 15
colors are incorrect 21
Computer 2 connector 8
computer connections
optional 7
required 7
computer image
optimize 27
troubleshooting 17
connector panel 6
Download from Www.Somanuals.com. All Manuals Search And Download.
43
I
image
Mask 35
display computer 9
display video 14
image does not fit screen 20
image not centered 23
image not sharp 20
image not square 20
image reversed 21
image size matrix 42
image upside down 21
IP Address 36
K
Keystone 12
keystone 30
L
lamp replacement 38
lamp won’t turn on 22
Language 36
laptop
connecting 7
external video port 9
LED
blinking green 16
blinking red 22
solid green 16
solid red 22
optional accessories 41
positioning 12
LED behavior 16
lens, cleaning 37
leveling foot 12
lock, security 40
shutdown 16
standard accessories 41
troubleshooting problems 16
Download from Www.Somanuals.com. All Manuals Search And Download.
44
R
V
Rear 33
remote control 25
VESA connector 8
Video button 14
advancing slides 25
Effect key 25
not working 19
replacing the lamp 38
Reset 36
resetting the lamp timer 39
RS-232 control 8
S
Screen Save 16
security lock 40
serial connection 8
Settings menu 33
solid green 16
solid red 16
Source troubleshooting 17
Sources 33
speakers, connecting 26
standard accessories 41
startup logo 34
Subnet mask 36
S-video connector 13
T
Tint 15
Troubleshooting 16 - 23
U
USB drivers 11
USB, connecting 7
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio Visual Products
Dukane Corporation
Audio Visual Products Division
2900 Dukane Drive
St. Charles, IL 60174-3395
E-mail: [email protected]
Phone: (630) 762-4040
Orders: (800) 676-2485
Information: (800) 676-2486
Fax: (630) 584-5156
Parts & Service: (800) 676-2487
Fax: (630) 584-0984
Part # 401-8758/8772-00
Download from Www.Somanuals.com. All Manuals Search And Download.
|