Dukane Projector 8755B User Manual

LIQUID CRYSTAL PROJECTOR

8755B

USER'S MANUAL

Download from Www.Somanuals.com. All Manuals Search And Download.

LCD Projector 28A8755B

USER'S MANUAL Vol.1 (Basic)

Thank you for purchasing this projector.

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct

usage through understanding. After reading, store this instruction manual in a

safe place for future reference.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without express

written authority.

TRADEMARK ACKNOWLEDGEMENT :

• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

• All other trademarks are the property of their respective owners.

CONTENTS

Page

PROJECTOR FEATURES................2

PREPARATIONS ..............................2

PART NAMES...................................4

SETTING UP

THE PROJECTOR ............................6

CONNECTING

YOUR DEVICES................................8

USING THE REMOTE

CONTROL.......................................13

TURNING ON THE POWER ...........14

TURNING OFF THE POWER .........16

ADJUSTING THE VOLUME ...........17

TEMPORARILY MUTING

THE SOUND....................................17

ADJUSTING THE POSITION..........18

USING THE AUTOMATIC

Page

CORRECTING KEYSTONE

DISTORTIONS ................................20

USING THE MAGNIFY

FEATURE........................................21

FREEZING THE SCREEN ..............21

SIGNAL SEARCHING.....................22

SELECTING THE ASPECT

RATIO..............................................22

TEMPORARILY BLANKING

THE SCREEN..................................22

USING THE MENU

FUNCTIONS....................................23

OPERATING THE PC SCREEN .....24

THE LAMP ......................................25

THE AIR FILTER.............................27

OTHER CARE.................................29

ADJUSTMENT FEATURE ..............19

Download from Www.Somanuals.com. All Manuals Search And Download.

This liquid crystal projector is used to project

various computer signals as well as NTSC / PAL /

SECAM video signals onto a screen. Little space

is required for installation and large images can

easily be realized.

PROJECTOR

FEATURES

Ultra High Brightness

Keystone Distortion Correction

ꢀ

Crisp, ultra-bright presentations is achieved

by using a UHB (ultra high brightness) lamp

and a highly efficient optical system

Quick correction of distorted images electrically

Partial Magnification Function

Whisper Mode Equipped

ꢀ

Interesting parts of images can be magnified

for closer viewing

Special mode is available for reducing

projector noise to achieve quieter operation

Your projector should come with the items

shown below. Check to make sure that all the

items are included. Contact your dealer if

anything is missing.

PREPARATIONS

NOTE • Keep the original packing material for future reshipment.

R E S E T

E N O T S Y E K

P O W E R

I N P

Power cord

(UK Type)

T E N P

N O

Y B D N A T S

USB mouse

cable

L A

Projector

(with Lens Cap)

Video/Audio cable

RGB cable

Liquid Crystal Projector

ED-S3170A/ED-X3270A

USER'S MANUAL Vol.1 Basic

Please read this user's manual thoroughly to ensure correct usage through understanding.

BEDIENUNGSANLEITUNG Teil

Grundlagen

Bitte lessen Sie diese Benutzerhandbuch zugunsten der korrekten Bedienung aufmerksam.

MANUEL D'UTILISATION Vol.1 Fondements

Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le fonctionnement de l'appareil.

STANDBY/ON

MANUALE D'ISTRUZIONI Vol.1 Informazioni di base

Vi preghiamo voler leggere attentamente il manuale d'istruzioni in modo tale da poter comprendere quanto riportato

ai fini di un corretto utilizzo del proiettore.

VIDEO

RGB

AUTO

MANUAL DE USUARIO Vol.1 Básico

Lea cuidadosamente este manual del usuario para poder utilizar corretamente el producto.

GEBRUIKSAANWIJZING Vol.1 Basis

Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te hebben van de

uitgebreide mogelijkheden.

BRUKERHÅNDBOK Vol.1 Grunnleggende

være garantert driftssikker bruk.

Vennligst les denne bruksanvisningen grundig for

ASPECT

BLANK

VOLUME

NSTRUÇÕES DO PROPRIETÁRIO Vol.1 Básico

Para assegurar uso correto do equipamento, por favor leia atentamente este manual do utilizador.

MAGNIFY

HOME

END

PAGE UP

R E S E

S Y E

I N

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

User's Manuals

(Vol.1/Vol.2)

Safety Instructions

POSITION

Two AA batteries

(for the remote

control)

ENTER

ESC

RESET

Remote control

Download from Www.Somanuals.com. All Manuals Search And Download.

WARNING Precautions to observe in regards to the power cord: Please use extra

caution when connecting the projector's power cord as incorrect or faulty

connections may result in FIRE AND/OR ELECTRICAL SHOCK. Please adhere to the

following safety guidelines to insure safe operation of the projector:

•

Only plug the power cord into outlets rated for use with the power cord's specified voltage range.

• Only use the power cord that came with the projector.

• NEVER ATTEMPT TO DEFEAT THE GROUND CONNECTION OF THE THREE-

PRONGED PLUG!

• Make sure that you firmly connect the power cord to the projector and wall outlet.

Connect your devices to the projector

Connect your computer, VCR and/or other

devices you will be using to the projector.

～

Insert the batteries into the remote

control

Connect the power cord

(1) Connect the connector of the electrical power cord to the AC inlet of the main unit.

(2) Firmly plug the power cord's plug into the outlet

Power outlet

(1)

(2)

AC inlet

Power cord

Download from Www.Somanuals.com. All Manuals Search And Download.

THE PROJECTOR

PART NAMES

Indicates the corresponding

reference page

RESET button

MENU button

POWER indicator

KEYSTONE button

TEMP indicator

INPUT button

LAMP indicator

STANDBY/ON button

R E S E T

E N O T S Y E K

P O W E R

T U

I N P

T E N P

/ O Y B D N A T S

L A

Zoom ring

Focus ring

Air filter

Elevator button

Remote sensor

Lens cap

S-VIDEO IN port

AUDIO IN R and L ports

RGB IN 1 and 2 ports

VIDEO IN port

AC power inlet

LANP

TENP

POWER

Elevator button

AUDIO IN

1/2 port

CONTROL port

Power switch

RGB OUT port

USB port

AUDIO OUT port

Download from Www.Somanuals.com. All Manuals Search And Download.

THE REMOTE CONTROL

SEARCH button

STANDBY/ON button

RGB button

STANDBY/ON

VIDEO

RGB

AUTO

VIDEO button

AUTO button

BLANK button

ASPECT

BLANK

VOLUME

ASPECT button

HOME

END

PAGE UP

MAGNIFY

VOLUME button

MUTE button

MAGNIFY buttons

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

FREEZE button

KEYBOARD buttons

POSITION button

KEYSTONE button

POSITION

MENU button

ENTER

Cursor buttons

ESC

RESET

RESET button

ENTER button

ESC button

Download from Www.Somanuals.com. All Manuals Search And Download.

SETTING UP THE PROJECTOR

CAUTION • Install the projector in a suitable environment according to instructions

of the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

• If you press the elevator buttons without holding the projector, the projector might

crash down, overturn, smash your fingers and possibly result in malfunction. To

prevent damaging the projector and injuring yourself, ALWAYS HOLD THE

PROJECTOR whenever using the elevator buttons to adjust the elevator feet.

Adjusting the Projector's Elevator Feet

You can use the elevator feet to make adjustments if the surface on which you

need to set the projector is uneven or if you otherwise need to adjust the angle of

projection. The adjustment range of the elevator feet is 0 to 9 degrees.

Press and hold in the elevator

buttons

Raise or lower the projector to the

desired height and then release the

elevator buttons

When you release the elevator buttons, the elevator

feet will lock into position.

As necessary, you can also finely

adjust the height of the projector by

twisting the elevator feet by hand

Download from Www.Somanuals.com. All Manuals Search And Download.

Adjusting the Screen Size and Projection Distance

Refer to the illustrations and tables below to determine the screen size and

projection distance.

The values shown in the table are calculated for a full size screen

a:Distance from the projector to the screen ( 10%)

b:Distance from the lens center to the bottom of the screen ( 10%)

c:Distance from the lens center to the top of the screen ( 10%)

The screen

Top view

If 4:3 aspect ratio

a [inch (m)]

Min. Max.

Screen Size [inch (m)]

[inch (cm)] [inch (cm)]

30 (0.8)

40 (1.0)

50 (1.3)

60 (1.5)

70 (1.8)

80 (2.0)

90 (2.3)

100 (2.5)

120 (3.0)

150 (3.8)

200 (5.0)

250 (6.3)

300 (7.5)

35 (0.9) 42 (1.1) 1 (2) 17 (44)

47 (1.2) 56 (1.4) 1 (3) 23 (58)

59 (1.5) 71 (1.8) 1 (4) 29 (73)

71 (1.8) 85 (2.2) 2 (4) 34 (87)

83 (2.1) 100 (2.5) 2 (5) 40 (102)

95 (2.4) 114 (2.9) 2 (6) 46 (116)

107 (2.7) 129 (3.3) 3 (7) 51 (131)

119 (3.0) 143 (3.6) 3 (7) 57 (145)

143 (3.6) 172 (4.4) 3 (9) 69 (174)

180 (4.6) 216 (5.5) 4 (11) 86 (218)

240 (6.1) 288 (7.3) 6 (15) 114 (290)

300 (7.6) 361 (9.2) 7 (18) 143 (363)

360 (9.2) 433 (11.0) 9 (22) 171 (435)

Lens center

Side view

Top view

The screen

If 16:9 aspect ratio

a [inch (m)]

Min. Max.

Screen Size [inch (m)]

[inch (cm)] [inch (cm)]

30 (0.8)

40 (1.0)

50 (1.3)

60 (1.5)

70 (1.8)

80 (2.0)

90 (2.3)

100 (2.5)

120 (3.0)

150 (3.8)

200 (5.0)

250 (6.3)

300 (7.5)

38 (1.0) 46 (1.2) 2 (4)

51 (1.3) 61 (1.6) 2 (5)

64 (1.6) 77 (2.0) 3 (6)

77 (2.0) 93 (2.4) 3 (8)

90 (2.3) 109 (2.8) 4 (9)

104 (2.6) 125 (3.2) 4 (10) 43 (110)

117 (3.0) 140 (3.6) 5 (12) 49 (124)

130 (3.3) 156 (4.0) 5 (13) 54 (137)

156 (4.0) 188 (4.8) 6 (15) 65 (165)

196 (5.0) 235 (6.0) 8 (19) 81 (206)

261 (6.6) 314 (8.0) 10 (26) 108 (275)

327 (8.3) 393 (10.0) 13 (32) 135 (343)

393 (10.0) 472 (12.0) 15 (39) 162 (412)

16 (41)

22 (55)

27 (69)

32 (82)

38 (96)

Lens center

Side view

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING YOUR DEVICES

Devices You Can Connect to the Projector

(Refer to this section for planning your device

configuration to use for your presentation.)

CAUTION • Incorrect connecting could result in fire or electrical shock. Please

read this manual and the separate “SAFETY INSTRUCTIONS”.

ATTENTION Precautions to observe when connecting other devices to the projector

• Whenever attempting to connect other devices to the projector, please thoroughly

read the manual of each device to be connected.

• TURN OFF ALL DEVICES prior to connecting them to the projector. Attempting to

connect a live device to the projector may generate extremely loud noises or other

abnormalities that may result in malfunction and/or damage to the device and/or

projector. Refer to the “TECHNICAL” of the USER’S MANUAL (Vol.2) for the pin

assignment of connectors and RS-232C communication data.

• Make sure that you connect devices to the correct port. Incorrect connection may

result in malfunction and/or damage to the device and/or projector.

• A component cable and some other cables have to be used with core set. Use the

accessory cable or a designated-type cable for the connection. For cables that have

a core only at one end, connect the core to the projector.

• Secure the screws on the connectors and tighten.

Indicates the

corresponding

reference page

Display monitors

DVD players

10 Laptop computers

VCRs

Desktop computers

Download from Www.Somanuals.com. All Manuals Search And Download.

Ports and Cables

Refer to the table below to find out which projector port and cable to use for connecting a

given device. Use this table for determining which cables to prepare.

Function

Projector Port

Connection Cables

RGB IN 1

Accessory RGB cable or optional RGB

cable with D-sub 15-pin shrink jack and

inch thread screws

RGB input

RGB IN 2

RGB OUT

USB

RGB output

USB mouse control

Accessory USB cable

AUDIO IN 1

・Linked to RGB IN 1

Audio input from computer

Optional audio cable with stereo mini jack

AUDIO IN 2

・Linked to RGB IN 2

PS/2 mouse control

ADB mouse control

Serial mouse control

RS-232C communication

Optional PS/2 mouse cable

Optional ADB mouse cable

Optional serial mouse cable

Optional RS-232C cable

CONTROL

S-VIDEO IN

Optional S-video cable with mini DIN 4-pin

jack

S-video input

Video input

VIDEO IN

Accessory audio/video cable

AUDIO IN L

AUDIO IN R

Audio input from video

equipment

Accessory audio/video cable or optional

audio cable with RCA jack

Audio output

AUDIO OUT

Optional audio cable with stereo mini jack

NOTE

About Plug-and-Play Capability

• This projector is compatible with VESA DDC 1/2B. Plug-and-Play can be achieved by

connecting this projector to computers that are VESA DDC (display data channel)

compatible. Please take advantage of this function by connecting the accessory RGB

cable to the RGB IN 1 port (DDC 1/2B compatible). Plug-and-Play may not work

properly if any other type of connection is attempted.

• Plug-and-Play is a system composed of the computer, its operating system and

peripheral equipment (i.e. display devices).

• Please use the standard drivers as this projector is a Plug-and-Play monitor.

• Plug-and-Play may not function properly with some type of computers. Use the RGB

IN 2 port if Plug-and-Play does not function correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING YOUR DEVICES (continued)

Connecting to a Computer

ATTENTION Whenever attempting to connect a laptop computer to the projector,

be sure to activate the laptop's RGB external image output (set the laptop to CRT

display or to simultaneous LCD and CRT display). For details on how this is done,

please refer to the instruction manual of the corresponding laptop computer.

RGB IN

AUDIO IN

(MONO) VIDEO IN

AUDIO IN

(MONO) VIDEO IN

S-VIDEO IN

RGB OUT

CONTROL

AUDIO IN

AUDIO OUT

RGB OUT

CONTROL

USB

AUDIO IN

AUDIO OUT

USB

USB cable

If connecting to a

USB port equipped

computer

Laptop computer

Desktop computer

NOTE

• Some computers may have multiple display screen modes. Use of some of these

modes will not be possible with this projector.

• For some RGB input modes, the optional Mac adapter is necessary.

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting to a DVD Player

RGB IN

AUDIO IN

(MONO) VIDEO IN

S-VIDEO IN

RGB OUT

CONTROL

AUDIO IN

AUDIO OUT

USB

S-VIDEO cable

If using a S-video

connection

If using an audio/video

connection

DVD player

Connecting to a VCR

RGB IN

AUDIO IN

(MONO) VIDEO IN

S-VIDEO IN

RGB OUT

CONTROL

AUDIO IN

AUDIO OUT

USB

S-VIDEO cable

If using a S-video

connection

VCR

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING YOUR DEVICES (continued)

Connecting to a Display Monitor

RGB IN

AUDIO IN

L / (MONO) VIDEO IN

S-VIDEO IN

RGB OUT

CONTROL

AUDIO IN

AUDIO OUT

USB

Display monitor

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE REMOTE CONTROL

Putting batteries into the remote control unit

CAUTION Precautions to observe in regards to the batteries

Always handle the batteries with care and use them only as directed. Improper use may result in

battery cracking or leakage, which could result in fire, injury and/or pollution of the surrounding environment.

• Keep the battery away from children and pets.

•

Be sure to use only the batteries specified for use with the remote control. Do not mix new batteries with used ones.

When inserting batteries, verify that the plus and minus terminals are aligned correctly (as indicated in the remote control).

• When you dispose the battery, you should obey the law in the relative area or country.

Remove the battery

cover

Slide back and remove

the battery cover in the

direction of the arrow.

Close the battery

cover

Replace the battery cover

in the direction of the arrow

and snap it back into place.

Insert the batteries

Align and insert the two AA

batteries (that came with the

projector) according to their plus

and minus terminals (as indicated

in the remote control).

Operating the remote control

•

The remote control works with both the

projector's front and rear remote sensors.

The range of the remote sensor on the front and

back is 3 meters with a 60-degree range (30

degrees to the left and right of the remote sensor).

Since the remote control uses infrared light to send

signals to the projector (Class 1 LED), be sure to

•

approximately

3 meters

approximately

3 meters

use the remote control in an area free from

obstacles that could block the remote control's

output signal to the projector.

ATTENTION

Precautions to observe when using the remote control

• Do not drop or otherwise expose the remote control to physical impact.

•

Do not get the remote control wet or place it on wet objects. Doing so may result in malfunction.

• Remove the batteries from the remote control and store them in a safe place if you

won't be using the remote control for an extended period.

• Replace the batteries whenever the remote control starts to malfunction.

•

When strong light, such as direct sunlight or light from an extremely close range (such as from an

inverter fluorescent lamp), hits the projector's remote sensor, the remote control may cease to function.

Adjust the direction of the projector to keep light from directly hitting the projector's remote sensor.

Download from Www.Somanuals.com. All Manuals Search And Download.

TURNING ON THE POWER

Precautions

～

Connect all devices to be used to the projector prior to turning on the power.

WARNING When the power is ON, a strong light is emitted. Do not look into the

lens.

Make sure that the power cord is firmly and

correctly connected to the projector and outlet

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

Turn on the projector's power

Set the power switch to [ | ] (ON). The projector will go

to STANDBY mode and the POWER indicator will light to

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

solid orange.

power switch

Control panel

LANP

TENP

POWER

POWER indicator

STANDBY/ON INPUT KEYSTONE RESET

Y/O

LAN

EYSTONE

RESET

T E S E R

E N O T S Y E K

R E

E T

N O

Y B D N A T S

N A

Press the STANDBY/ON button (control

panel or remote control)

• The projector begins warming up and the POWER

indicator blinks green.

STANDBY/ON

• The POWER indicator stops blinking

and lights to solid green once the

projector's power is completely on.

NOTE

Turn the

power on/off in

right order.

• Power on the

projector before the

computer or video

tape recorder.

Remove the lens cap

The picture is projected.

• Power off the

projector after the

computer or video

tape recorder.

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting an Input Signal

Using the remote control

Using the projector's control panel

If selecting RGB input

Press the RGB button

Press the INPUT button

As illustrated below, each time you

press the INPUT button, the projector

switches between its input signal

ports. Select the signal you wish to

project.

Press this button to toggle between the

devices connected to RGB IN 1 and 2.

As illustrated below, each time you

press the RGB button, the projector

switches between RGB IN 1 and 2.

Select the signal you wish to project.

INPUT

RGB IN 1

RGB IN 2

RGB

RGB IN 1

RGB IN 2

S-VIDEO IN

VIDEO IN

If selecting video input

Press the VIDEO button

Press this button to toggle between the

devices connected to VIDEO IN and S-

VIDEO IN. As illustrated below, each

time you press the VIDEO button, the

projector switches between VIDEO IN

and S-VIDEO IN. Select the signal you

wish to project.

VIDEO

VIDEO IN

S-VIDEO IN

Use the zoom ring to adjust the

screen size

Use the focus ring to focus the

picture

Download from Www.Somanuals.com. All Manuals Search And Download.

TURNING OFF THE POWER

Press the STANDBY/ON button (control

panel or remote control)

The message "Power off?" will appear on the screen for approximately 5 seconds.

STANDBY/ON

VIDEO

RGB

AUTO

STANDBY/ON

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

Press the STANDBY/ON button again

(control panel or remote control)

Press the STANDBY/ON button again while the "Power off?"

message is visible. The projector lamp goes off and starts cooling

down. The POWER indicator blinks orange while the lamp cools

down. (Pressing the STANDBY/ON button while the POWER

indicator is blinking orange has no effect.)

POSITION

ENTER

ESC

RESET

The system goes into the STANDBY mode after cooling

down and the POWER indicator stops blinking orange and

then lights to solid orange.

STANDBY/ON

Control panel

LANP

TENP

Check that the POWER indicator stops

POWER

blinking and lights to solid

power switch

orange.

Switch the power switch to

[O] (OFF).

STANDBY/ON INPUT KEYSTONE RESET

POWER indicator

Y/O

LANP

TENP

EYSTONE

RESET

T E S E R

E N O T S Y E K

R E

E T

N O

Y B D N A T S

N A

Confirm that the POWER indicator has

gone off and then attach the lens cap.

When the projector has completed powering down, the

POWER indicator will go off.

NOTE

• Except in

emergencies, follow

the above-

mentioned

procedure for

turning power off.

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE VOLUME

VOLUME

Press the VOLUME button

As illustrated on the right, a dialog will

STANDBY/ON

VIDEO

RGB

AUTO

appear on the screen to aid you in adjusting

the volume.

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

Press the

the volume

buttons to adjust

POSITION

Press the VOLUME button again to close the dialog and

complete this operation. (Even if you don't do anything, the

dialog will automatically disappear after a few seconds.)

ENTER

ESC

RESET

VOLUME

Press this to increase the volume

Press this to decrease the volume

TEMPORARILY MUTING THE SOUND

Press the MUTE button

STANDBY/ON

As illustrated on the right, a dialog will appear on the

screen indicating that you have muted the sound. Press

the VOLUME button to close the dialog. (Even if you don't

do anything, the dialog will automatically disappear after

a few seconds.)

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

Press the MUTE button again to restore the sound.

FREEZE

KEYSTONE

VOLUME

MUTE

POSITION

ENTER

ESC

RESET

Download from Www.Somanuals.com. All Manuals Search And Download.

ADJUSTING THE POSITION

Press the POSITION button

As illustrated on the right, a dialog will appear on the screen

to aid you in adjusting the position.

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

POSITION

OFF

FREEZE

KEYSTONE

POSITION

ENTER

Use the

the position

When you want to initialize the position, press the RESET

button during adjustment.

buttons to adjust

ESC

RESET

Press the POSITION button again to close the dialog and

complete this operation. (Even if you don't do anything, the

dialog will automatically disappear after a few seconds.)

This function is only available for RGB IN 1/2 input.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE AUTOMATIC ADJUSTMENT FEATURE

Press the AUTO button

AUTO

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

Automatic Adjustment for RGB Input

PAGE DOWN

MUTE

Horizontal position (H. POSIT), vertical position (V.

POSIT), clock phase (H. PHASE) and horizontal size (H.

SIZE) are automatically adjusted.

OFF

FREEZE

KEYSTONE

Make sure that the application window is set to its

maximum size prior to attempting to use this feature.

Dark pictures may still be incorrectly adjusted. Use a

bright screen when adjusting.

POSITION

ENTER

ESC

RESET

Automatic Adjustment for Video Input

The signal type best suited for the respective input

signal is selected automatically.

This feature is available only if VIDEO is set to AUTO in

the INPUT menu.

NOTE

The automatic adjustment operation requires approximately 10 seconds. Also, please

note that it may not function correctly with some input signals.

Download from Www.Somanuals.com. All Manuals Search And Download.

CORRECTING KEYSTONE DISTORTIONS

Press the KEYSTONE button

KEYSTONE

As illustrated on the right, a dialog will appear

STANDBY/ON

VIDEO

RGB

AUTO

on the screen to aid you in correcting the

distortion.

ASPECT

BLANK

VOLUME

KEYSTONE

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

POSITION

Use the

buttons to select the

direction of distortion to correct (

)

ENTER

ESC

RESET

Use the

distortion

buttons to correct the

Press the KEYSTONE button again to close the dialog and

complete this operation. (Even if you don't do anything, the

dialog will automatically disappear after a few seconds.)

NOTE

• This function may not be work well with some types of input signals.

• The adjustable range for correcting keystone distortions will vary with the type of

input signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE MAGNIFY FEATURE

Press the MAGNIFY (ON) button

The projector enters MAGNIFY mode.

MAGNIFY

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

Press the POSITION button, then use the

PAGE DOWN

MUTE

buttons to select the area to enlarge and then

press the POSITION button again to confirm your

selection

OFF

FREEZE

KEYSTONE

POSITION

ENTER

ESC

RESET

Press the

out of the selected area.

buttons to zoom in and

Press the MAGNIFY (OFF) button to exit MAGNIFY mode

and restore the screen to normal. (The projector will also

automatically exit MAGNIFY mode if there is a change in the

input signal's state.)

NOTE

The projector will automatically exit from MAGNIFY mode if either the INPUT SELECT,

AUTO, ASPECT or VIDEO feature is used, or, if there is a change in the input signal's state.

FREEZING THE SCREEN

Press the FREEZE button

MAGNIFY

HOME

PAGE UP

VOLUME

FREEZE

The [II] icon appears and the screen will freeze at

the current image. Press the FREEZE button again

and the [ ] appears as the projector exits FREEZE

mode.

END

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

POSITION

NOTE

•

The projector will automatically exit from FREEZE mode if either the POSITION, VOLUME, MUTE, AUTO,

BLANK ON/OFF or MENU ON/OFF feature is used, or, if there is a change in the input signal's state.

If the projector continues projecting the same image for a long time (i.e. you forget to exit FREEZE mode),

the image might possibly remain as an afterimage. Do not leave the projector in FREEZE mode for too long.

Download from Www.Somanuals.com. All Manuals Search And Download.

SIGNAL SEARCHING

Press the SEARCH button

When you press the SEARCH button, the projector begins

searching for input signals. If it detects an input signal, the

search will cease and the projector will project the detected

signal. If the projector is unable to find an input signal at any of

its ports, it will return to the state it was in prior to the search.

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

RGB IN 1

RGB IN 2

VIDEO IN

FREEZE

KEYSTONE

S-VIDEO IN

SELECTING THE ASPECT RATIO

Press the ASPECT button

STANDBY/ON

VIDEO

RGB

AUTO

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

RGB IN 1, RGB IN 2,

OFF

FREEZE

KEYSTONE

4:3

16:9

VIDEO IN, S-VIDEO IN,

POSITION

4:3

16:9

SMALL

ENTER

ESC

RESET

TEMPORARILY BLANKING THE SCREEN

Press the BLANK button

The input signal screen is shut off, and a blank screen

STANDBY/ON

VIDEO

RGB

AUTO

appears. You can set the blank screen using the menu

(from the SCREEN menu, select BLANK). Press the BLANK

button again to remove the blank screen, and return to the

input signal screen.

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

BLANK

POSITION

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE MENU FUNCTIONS

Press the MENU button

The menu display appears on the screen. The

STANDBY/ON

VIDEO

RGB

AUTO

projector has the following menus: MAIN,

PICTURE-1, PICTURE-2, INPUT, SCREEN, and

ASPECT

BLANK

VOLUME

OPTION. Select a menu using the

buttons. The

MAGNIFY

HOME

END

PAGE UP

current settings of the items that can be manipulated via the

selected menu appear.

PAGE DOWN

MUTE

OFF

FREEZE

KEYSTONE

Select a menu using the

then press the

buttons,

or ENTER button.

The display of the selected menu appears.

POSITION

ENTER

[ex. Adjusting SHARPNESS]

Use the

the

buttons to select PICTURE-1, then press

ESC

RESET

or ENTER button.

MAIN

COLOR BAL R

COLOR BAL B

SHARPNESS

COLOR

–1

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

TINT

ENTER

: SELECT

Select an item using the

or ENTER button.

buttons, then press the

The operation display of the selected item appears. To adjust a numerical value,

press the

or ENTER button again to switch to the single menu (small display

showing only the operation display area).

[ex. Adjusting SHARPNESS]

Use the

press the

buttons to select SHARPNESS, then

or ENTER button.

MAIN

COLOR BAL R

COLOR BAL B

SHARPNESS

COLOR

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

TINT

ENTER

: SELECT

Press the

buttons to adjust the level.

Press the MENU button to hide the menu and finish your operation. Alternatively,

press the

[ex. Adjusting SHARPNESS]

Use the buttons to adjust the SHARPNESS.

or ESC button to return to the previous display.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING THE PC SCREEN

You can use the remote control as a simplified mouse or keyboard.

CAUTION Caution: Mistaken use of the mouse/keyboard control could damage your equipment.

•

Only connect to a PC.

Before connecting, read the manuals of the device you will connect.

Do not unplug the connector cables while the computer is operating.

PS/2, ADB, Serial Mouse Control

STANDBY/ON

VIDEO

RGB

AUTO

1. Turn off the projector and PC power, and connect the projector’s

CONTROL terminal to the computer via the mouse cable.

2. If a USB cable is connected, disconnect it. If a USB cable is connected, the USB control

function is given priority, and mouse control from the CONTROL terminal will not function.

3. Turn on the projector power, then the computer.

ASPECT

BLANK

VOLUME

MAGNIFY

HOME

END

PAGE UP

PAGE DOWN

MUTE

The functions in the table below can be controlled. If you have difficulty with control,

restart the computer (either from the software or by pressing the restart button).

OFF

FREEZE

KEYSTONE

Available Functions

Remote Control Operation

Move Pointer

Use

buttons

POSITION

Left click with mouse

Right click with mouse

Press ENTER button

Press RESET button

ENTER

ESC

RESET

USB Mouse/Keyboard Control

1. Connect the projector’s USB terminal to the computer using a USB cable.

The functions in the table below can be controlled.

Available Functions

Remote Control Operation

Move Pointer

Use

buttons

Left click with mouse

Press ENTER button

Press RESET button

Press HOME button

Press END button

Right click with mouse

Press keyboard’s HOME key

Press keyboard’s END key

Press keyboard’s PAGE UP key

Press keyboard’s PAGE DOWN key

Press keyboard’s ESC key

Press PAGE UP button

Press PAGE DOWN button

Press ESC button

NOTES

•

It may not be possible to control notebook PCs, and other computers with built-in pointing devices (e.g.

track balls), using this remote control. In this case, before connecting go into BIOS (system setup) and

select external mouse, and disable the pointing devices. In addition, the mouse may not function if the

computer does not have the needed utility program. See your computer’s hardware manual for details.

The USB control can be used with Windows 95 OSR 2.1 or higher. It may not be possible to

use the remote control, depending on the computer’s configurations and mouse drivers.

The USB control can only be used for the functions listed above. You cannot do things like press two buttons

at once (for instance, pressing two buttons at the same time to move the mouse pointer diagonally).

This function is not available while the lamp is warming up (the POWER indicator flashes green), while adjusting the volume and

display, correcting for trapezoidal distortion, zooming in on the screen, using the BLANK function, or displaying the menu screen.

•

Download from Www.Somanuals.com. All Manuals Search And Download.

THE LAMP

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Before replacing the lamp, check the serial number of the replacement lamp bulb (sold separately:

DT00521), then contact your local dealer. Before replacing

the lamp, turn off the power, and unplug the power cord, then wait at least 45 minutes, in order to

ensure that the lamp is properly cooled. Removing the lamp bulb while it is still hot could cause

burns, or cause the lamp bulb to burst.

The LCD projector uses a glass lamp bulb. It is a mercury lamp with high

WARNING

internal pressure. High-pressure mercury lamps can break with a loud

bang, or burn out, if jolted or scratched, or through wear over time. Each lamp has a

different lifetime, and some may burst or burn out soon after you start using them. In

addition, when the bulb bursts, it is possible for shards of glass to fly into the lamp housing,

and for gas containing mercury to escape from the projector’s vent holes.

•

Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

If the replace lamp indicator (see "Related Messages" (Vol.2

) and "Regarding the

indicator Lamps" (Vol.2

)) comes on, replace the lamp as soon as possible. Using the

lamp for long periods of time, or past the replacement date, could cause it to burst. Do

not use old (used) lamps; this is a cause of breakage.

•

If the lamp breaks soon after the first time it is used, it is possible that there are electrical problems

elsewhere besides the lamp. If this happens, contact your local dealer.

If the lamp should break (it will make a loud bang when it does), ventilate the room well, and make

sure not to breathe the gas that comes out of the projector vents, or get it in your eyes or mouth.

If the lamp should break (it will make a loud bang when it does), unplug the power cord from

the outlet, and make sure to request a replacement lamp from your local dealer. Note that

shards of glass could damage the projector’s internals, or cause injury during handling, so

please do not try to clean the projector or replace the lamp yourself.

•

Obey local ordinances when disposing of used lamps. In most cases, it is possible to dispose of used

bulbs in the same manner as used glass bottles, but in some cases, bulbs are sorted separately.

• Do not use the projector with the lamp cover removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

THE LAMP (continued)

Replacing the lamp

All projector lamps will wear out eventually. If used for long periods of time, the image could become

darkened, and the color contrast could be impacted as well. We recommend that you replace your lamps

early. If the LAMP indicator turns red, or a message prompts you to replace the lamp when you power up

the projector, the lamp needs to be replaced. (See "Related Messages" (Vol.2

Indicator Lamps" (Vol.2 ) for details.)

) and "Regarding the

Turn off the projector, and unplug the

power cord. Allow the lamp bulb to cool

for at least 45 minutes, and prepare a

new lamp.

Insert the new lamp, and tighten the 1

screw firmly to lock it in place

•

Also steadily push the opposite side of the

screwed side of the

lamp into the unit.

After making sure that the projector has

cooled adequately, slowly flip over the

projector, so that the bottom is facing up

Replace the lamp cover, and tighten

the 2 screws firmly to lock it in

place

Unscrew the 2

screws, and

remove the

lamp cover

Unscrew the 1 screw, and slowly pull

out the lamp by the handle

Slowly turn the projector so that

the top is facing up

•

Be careful not to touch the inside of the lamp case.

Turn on the projector power, and using

the menu, reset the lamp timer

•

To reset the lamp timer, from the OPTION

menu, select LAMP TIME.

ATTENTION • Make sure that the screws are screwed in firmly. Loose screws could result in damage or injury.

• Do not use with lamp cover removed.

•

Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always when replacing

the lamp. The message functions will not operate properly if the lamp timer is not reset correctly.

• When the lamp has been replaced after the message of "CHANGE THE LAMP ...THE POWER

WILL TURN OFF AFTER 0 hr." is displayed, or the LAMP indicator is red, complete the following

operation within 10 minutes of switching power ON.

NOTE

• The LAMP indicator is also red when the lamp unit reaches high temperature.

Before replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power

ON again. If the LAMP indicator is still red, replace the lamp.

Download from Www.Somanuals.com. All Manuals Search And Download.

THE AIR FILTER

Caring for the air filter

The air filter should be cleaned about every 100 hours. If the LAMP indicator and

TEMP indicator blink red simultaneously, or a message prompts you to clean the air

filter when you turn on the unit, the filter needs to be cleaned. (See "Related

Messages" (Vol.2

) and "Regarding the Indicator Lamps" (Vol.2

) for details.)

Turn off the projector, and unplug the power cord

Apply a vacuum cleaner to

the top of the air filter cover

to clean the air filter

Air Filter Cover

Turn on the projector, and use the menu to reset the filter

timer

• To reset the air filter timer, from the OPTION menu, select FILTER TIME.

Download from Www.Somanuals.com. All Manuals Search And Download.

THE AIR FILTER (continued)

Replacing the air filter

If the soiling will not come off the air filter, or it becomes damaged, then it needs to be

replaced. Please contact your local dealer, after confirming the model of your

separately sold replacement air filter. (See "Optional Parts" on Vol.2

Turn off the projector, and unplug the power cord. Prepare a

new air filter (one specified for your projector)

Remove the air filter cover and air filter

Insert the new filter, and replace the

filter cover

Turn on the projector power, and using the menu, reset the

filter timer

• To reset the lamp timer, from the OPTION menu, select FILTER TIME.

ATTENTION • Make sure to turn off the power and unplug the power cord before caring for

the unit. Please carefully read "Safety Instructions", in order to care for your projector correctly.

• Do not use with air filter cover removed.

• If the air filter becomes clogged by dust or the like, internal temperature rises and could cause

malfunction. The power is automatically turned off in order to prevent the unit from overheating

internally.

Download from Www.Somanuals.com. All Manuals Search And Download.

OTHER CARE

Caring for the inside of the projector :

In order to ensure the safe use of your projector, please have it cleaned and inspected by

your local dealer about once every 2 years. Never try to care for the inside of the unit

yourself. Doing so is dangerous.

Caring for the lens :

Lightly wipe the lens with a commercially available lens-cleaning wipe. Do not touch the

lens directly with your hand.

Caring for the cabinet and remote control transmitter :

Wipe lightly with gauze or a soft cloth. If soiling is severe, dip a soft cloth in water or a

neutral cleanser diluted in water, and wipe lightly after wringing well. Then, wipe lightly

with a soft, dry cloth.

ATTENTION • Make sure to turn off the power and unplug the power cord before caring for

the unit. Please carefully read "Safety Instructions" in this manual, in order to care for your projector

correctly.

• Do not use cleaners or chemicals other than those listed above, including benzene and paint

thinner.

• Do not use aerosols or sprays.

• Do not polish or wipe with hard objects.

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL

SIGNAL CONNECTOR PIN ASSIGNMENT

RGB IN [1]/[2]

RGB OUT

S-VIDEO

D-sub 15-pin Shrink

Mini Din 4-pin

Pin No

Signal

Video input Red

Video input Green

Video input Blue

Pin No

Signal

Pin No Signal

Color:

Ground

0.286Vp-p (NTSC, burst signal),

75Ω terminator

0.3Vp-p (PAL/SECAM, burst signal),

75Ω terminator

Brightness:

1.0Vp-p, 75Ω terminator

RGB IN [1]: SDA (DDC)

Ground

RGB IN [2]:

RGB OUT :

Ground Red

Ground Green

Ground Blue

H. sync./ Composite sync.

Vertical sync

Ground

RGB IN [1]: SCL (DDC)

RGB IN [2]:

RGB OUT :

signal

Terminal

Specification

Video: Analog 0.7Vp-p, 75Ω terminator (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB IN

D-sub 15-pin shrink jack

RGB signal

input

AUDIO IN 1

200mVrms,50kΩ (max.3.Ovp-p)

Stereo mini jack

AUDIO IN 2

VIDEO IN

1.0Vp-p, 75Ω terminator, RCA jack

Brightness signal: 1.0Vp-p, 75Ω terminator

Color signal: 0.286Vp-p (NTSC, burst signal),75Ω terminator

0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator

Mini DIN 4-pin jack

Video signal

input

S-VIDEO IN

200mVrms, 50 kΩ (max. 3.0Vp-p)

RCA jack

AUDIO IN

Video: Analog 0.7Vp-p, 75Ω output impedance (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB OUT

Signal output

D-sub 15-pin shrink jack

200mVrms, out put impedance1kΩ (max.3.Ovp-p)

Stereo mini jack

AUDIO OUT

Download from Www.Somanuals.com. All Manuals Search And Download.

EXAMPLE OF COMPUTER SIGNAL

Display mode

ED-S3170A

Resolution

fH (kHz)

fV (Hz)

Rating

Signal mode

H × V

ED-X3270A

Zoom in

720 × 400

640 × 480

800 × 600

832 × 624

1024 × 768

1152 × 864

1280 × 960

1280 × 1024

37.9

31.5

35.0

37.9

37.5

43.3

35.2

37.9

48.1

46.9

53.7

49.7

48.4

56.5

60.0

68.7

67.5

60.0

64.0

80.0

85.0

59.9

66.7

72.8

75.0

85.0

56.3

60.3

72.2

75.0

85.1

74.5

60.0

70.1

75.0

85.0

75.0

60.0

75.0

VESA

TEXT

Zoom in

VGA (60Hz)

Mac13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

SXGA (75Hz)

SXGA (60Hz)

SXGA (75Hz)

VESA

Zoom out

VESA

Zoom out

1280 × 1024

1600 × 1200

91.2

75.0

85.0

60.0

VESA

SXGA (85Hz)

UXGA (60Hz)

Zoom out

NOTE • Some computers may have multiple display screen modes. Use of some

of these modes will not be possible with this projector.

• Be sure to check jack type, signal level, timing and resolution before connecting this

projector to a computer.

• Depending on the input signal, full-size display may not be possible in some cases.

Refer to the number of display pixels above.

• This projector will display up to UXGA (1600X1200) resolution signals but the image

will be rescaled to the native resolution of the projector. Best display performance is

achieved when the signal input resolution is the same as the native resolution of the

projector.

• The image may not be displayed correctly when the input sync. signal is “Composite

Sync.” or “Sync. on G”.

Download from Www.Somanuals.com. All Manuals Search And Download.

INITIAL SET SIGNALS

The following signals are used for the initial settings.

The signal timing of some computer models may be different. In such case, refer to

adjust the V.POSIT and H.POSIT of the menu.

Back porch b

Front porch d

Back porch b

Display interval c

Front porch d

Display interval c

Sync a

Computer /

Signal

Horizontal signal timing (µs)

Computer /

Signal

Vertical signal timimg (lines)

400

TEXT

2.0

3.0

20.3

1.0

TEXT

VGA (60Hz)

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

1280×1024 (85Hz)

1600×1200 (60Hz)

3.8

2.1

1.3

2.0

1.6

2.0

3.2

2.4

1.6

1.1

2.1

1.8

1.2

1.0

1.2

1.0

1.1

1.0

1.2

1.9

3.2

3.8

2.2

3.6

2.2

1.3

3.2

2.7

3.9

2.5

1.9

2.2

2.4

2.9

2.3

1.8

1.4

1.9

25.4

21.2

20.3

17.8

22.2

20.0

16.0

16.2

14.2

14.5

15.8

13.7

13.0

10.8

10.7

11.9

9.5

0.6

2.1

1.0

0.5

1.6

0.7

1.0

1.1

0.3

0.6

0.4

0.3

0.2

0.5

0.6

0.9

0.4

0.2

0.4

VGA (60Hz)

480

600

624

768

864

960

1024

1200

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

1280×1024 (85Hz)

1600×1200 (60Hz)

8.1

9.9

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTION TO THE MOUSE CONTROL

Projector

Computer

ADB Mouse

ADB

(

)

POWER ON

DATA

RTS

+5V

GND

Mouse jack

Mini DIN 4-pin

CONTROL Terminal

D-sub 15-pin shrink jack

+5V

GND

Serial Mouse

Projector

Computer

CONTROL Terminal

DTR

GND

DSR

RTS

CTS

Mouse jack

D-sub 9-pin

SEL0

RTS

D-sub 15-pin shrink jack

GND

USB Mouse

USB jack

(B type)

Projector

Computer

USB jack

(A type)

1 +_5V

—

DATA 2

—

DATA

GND

USB cable

Projector

Computer

PS/2 Mouse

DATA

CLK

DATA

GND

+5V

CLK

Mouse jack

Mini DIN 6-pin

CONTROL Terminal

D-sub 15-pin shrink jack

SEL0

RTS

+5V

GND

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C COMMUNICATION

(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.

(2) Turn on the computer power supply and after the computer has started up, turn on the

projector power supply.

RS-232C jack

D-sub 9-pin

Projector

Computer

Control jack

D-sub 15-pin shrink jack

Communications setting

19200bps, 8N1

1 Protocol

Consist of header (7 bytes) + command data (6 bytes).

2 Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low : Lower byte of CRC flag for command data.

CRC_high : Upper byte of CRC flag for command data.

3 Command data

Command data chart

byte_0

byte_1

high

byte_2

byte_3

byte_4

low

byte_5

Action

Type

Setting code

low

high

Action (byte_0 - 1)

Action

Classification

Content

SET

GET

Change setting to desired value.

Read projector internal setup value.

Increment setup value by 1.

Decrement setup value by 1.

Run a command.

INCREMENT

DECREMENT

EXECUTE

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-232C COMMUNICATION (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes)

+‘00H’+‘00H’) from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) +

setting code (2 bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+

type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the specified setting to the default value.

(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+

type (2 bytes) +‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+

type (2 bytes) +‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

When a command sent by the projector cannot be understood by the computer

When the command sent by the projector cannot be understood, the error command ‘15H’ is

returned by the computer. Some times, the projector ignores RS-232C commands during

other works. If the error command ‘15H’ is returned, please send the same command again.

When data sent by the projector cannot be practice

When the command sent by the projector cannot be practiced, the the error code ‘1cH’

+‘xxxxH’ is returned.

When the data length is greater than indicated by the data length code, the projector will

ignore the excess data code.

Conversely, when the data length is shorter than indicated by the data length code, an

error code will be returned to the projector.

NOTE • Operation cannot be guaranteed when the projector receives an

undefined command or data.

•

Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the

lamp is lit. Ignore this data.

• Commands are not accepted during warm-up.

Download from Www.Somanuals.com. All Manuals Search And Download.

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Blue

BE EF

06 00 CB D3 01 00 00 30

06 00 6B D0 01 00 00 30

06 00 9B D0 01 00 00 30

06 00 FB CA 01 00 00 30

06 00 FB E2 01 00 00 30

03 00

05 00

06 00

20 00

40 00

00 00

01 00

02 00

03 00

00 00

01 00

00 00

01 00

20 00

00 00

01 00

02 00

03 00

04 00

05 00

06 00

07 00

08 00

White

Black

MyScreen

ORIGNAL

Get

Set

Blank Color

06 00

06 00 C7 D2 01 00 01 30

06 00 57 D3 01 00 01 30

06 00 A7 D3 01 00 01 30

08 D3

02 00 00 30

Normal

H Inverse

V lnverse

H&V Inverse

Get

Mirror

06 00

37 D2

F4 D2

83 D2

13 D3

01 00 01 30

02 00 01 30

01 00 02 30

Normal

Freeze

Set

Freeze

Startup

Get

06 00 B0 D2 02 00 02 30

06 00 0B D2 01 00 04 30

06 00 9B D3 01 00 04 30

06 00 CB CB 01 00 04 30

ORIGNAL

OFF

MyScreen

Get

06 00

38 D2

F7 D3

67 D2

97 D2

07 D3

37 D1

02 00 04 30

01 00 05 30

English

Français

Deutsch

Español

Italiano

Norsk

06 00 A7 D0 01 00 05 30

06 00 57 D0 01 00 05 30

06 00 C7 D1 01 00 05 30

06 00 37 D4 01 00 05 30

06 00 A7 D5 01 00 05 30

06 00 57 D5 01 00 05 30

Set

Language

Nederlands

Português

BE EF

09 00

中文

BE EF

0A 00

00 00

Get

06 00 C4 D3 02 00 05 30

06 00 7C D2 02 00 07 30

06 00 1A D2 04 00 07 30

06 00 CB D3 05 00 07 30

Magnify

Auto off

Increment

Decrement

Get

06 00

08 86

6E 86

BF 87

02 00 10 31

04 00 10 31

05 00 10 31

Increment

Decrement

BE EF

00 00

Brightness

Reset

Execute

BE EF

06 00

58 D3

06 00 00 70

00 00

Contrast Reset

06 00 A4 D2 06 00 01 70

06 00 E0 D2 06 00 02 70

V.Position

Reset

Download from Www.Somanuals.com. All Manuals Search And Download.

Command data chart (continued)

Command data

Action Type Setting code

Names

Operation type

Header

CRC

IC D3

68 D2

H.Position Reset

H.Size Reset

Execute

BE EF

06 00

06 00 03 70

06 00 04 70

00 00

Color Balance

R Reset

Execute

BE EF

06 00

94 D3

06 00 05 70

00 00

Color Balance

B Reset

06 00 D0 D3 06 00 06 70

06 00 C4 D0 06 00 09 70

Sharpness Reset

Color Reset

Execute

BE EF

00 00

06 00

80 D0

06 00 0A 70

Tint Reset

06 00 7C D1 06 00 0B 70

Keystone_V Reset

Keystone_H Reset

Auto Adjust

06 00

08 D0

98 D8

91 D0

06 00 0C 70

06 00 20 70

06 00 0A 20

Lamp Time Reset

06 00 58 DC 06 00 30 70

06 00 98 C6 06 00 40 70

Filter Time Reset

Execute

off

BE EF

00 00

BE EF

06 00 FB D8 01 00 20 30

06 00 6B D9 01 00 20 30

06 00 C8 D8 02 00 20 30

06 00 D9 D8 02 00 20 60

00 00

01 00

00 00

Set

Blank on/off

Get

(Example of Return)

00 00 01 00

(Normal) (Cover-error)

02 00

(Fan-error)

03 00

(Lamp-error)

Error Status

Power

04 00 05 00

(Temp-error) (Air flow-error) (Lamp-Time-over) (Cool-error) (Filter-Error)

06 00

07 00

08 00

OFF

BE EF

06 00 2A D3 01 00 00 60

06 00 BA D2 01 00 00 60

00 00

01 00

00 00

Set

Get

06 00

19 D3

02 00 00 60

RGB1

RGB2

Video

BE EF

06 00 FE D2 01 00 00 20

06 00 3E D0 01 00 00 20

06 00 6E D3 01 00 00 20

06 00 9E D3 01 00 00 20

06 00 CD D2 02 00 00 20

00 00

04 00

01 00

02 00

00 00

Input Source

SVideo

Get

06 00

31 D3

57 D3

86 D2

02 00 01 20

04 00 01 20

05 00 01 20

Increment

Volume

Mute

Decrement

Normal

BE EF

00 00

01 00

00 00

06 00

46 D3

01 00 02 20

Set

Mute

Get

06 00 D6 D2 01 00 02 20

06 00

75 D3

89 D2

02 00 02 20

02 00 03 20

Get

Increment

Decrement

06 00 EF D2 04 00 03 20

06 00 3E D3 05 00 03 20

Brightness

Download from Www.Somanuals.com. All Manuals Search And Download.

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Get

BE EF

06 00 FD D3 02 00 04 20

06 00 9B D3 04 00 04 20

06 00 4A D2 05 00 04 20

00 00

Contrast

Increment

Decrement

Get

06 00

01 D2

67 D2

02 00 05 20

04 00 05 20

Color Balance R

Increment

Decrement

06 00 B6 D3 05 00 05 20

Get

BE EF

06 00

45 D2

23 D2

F2 D3

02 00 06 20

04 00 06 20

05 00 06 20

00 00

Color Balance B

Keystone_V

Increment

Decrement

Get

06 00 B9 D3 02 00 07 20

06 00 DF D3 04 00 07 20

06 00 0E D2 05 00 07 20

Increment

Decrement

Get

Increment

Decrement

4:3

BE EF

06 00 E9 D0 02 00 0B 20

00 00

06 00

8F D0

04 00 0B 20

Keystone_H

Aspect

06 00 5E D1 05 00 0B 20

BE EF

06 00 9E D0 01 00 08 20

06 00 0E D1 01 00 08 20

06 00 FE D1 01 00 08 20

06 00 AD D0 02 00 08 20

00 00

01 00

02 00

00 00

01 00

02 00

00 00

Set

16:9

Small

Get

Default

Bottom

Top

06 00

62 D1

F2 D0

02 D0

51 D1

0D 83

6B 83

BA 82

F1 82

97 82

46 83

01 00 09 20

02 00 09 20

02 00 00 21

04 00 00 21

05 00 00 21

02 00 01 21

04 00 01 21

05 00 01 21

Picture

Position at

16 : 9 or Small

Set

Get

V.Position

H.Position

Increment

Decrement

Get

Increment

Decrement

Get

BE EF

06 00

B5 82

D3 82

02 83

49 83

2F 83

FE 82

02 00 02 21

04 00 02 21

05 00 02 21

02 00 03 21

04 00 03 21

05 00 03 21

00 00

H.Size

Increment

Decrement

Get

H.Phase

Increment

Decrement

Get

BE EF

06 00

F1 72

97 72

46 73

B5 72

D3 72

02 73

02 00 01 22

04 00 01 22

05 00 01 22

02 00 02 22

04 00 02 22

05 00 02 22

00 00

Sharpness

Color

Increment

Decrement

Get

Increment

Decrement

Download from Www.Somanuals.com. All Manuals Search And Download.

Command data chart (continued)

Command data

Action Type Setting code

Names

Operation type

Header

CRC

Get

Increment

Decrement

Auto

BE EF

06 00

49 73

2F 73

FE 72

9E 75

FE 71

6E 70

6E 75

5E 72

FE 74

0E 71

0D 73

02 00 03 22

04 00 03 22

05 00 03 22

01 00 00 22

02 00 00 22

00 00

0A 00

04 00

05 00

09 00

02 00

08 00

07 00

00 00

01 00

00 00

01 00

00 00

01 00

02 00

00 00

02 00

01 00

00 00

01 00

03 00

00 00

01 00

00 00

Tint

NTSC

PAL

Set

SECAM

NTSC 4.43

M-PAL

N-PAL

Get

Video Format

off

06 00 CB D0 01 00 08 30

06 00 5B D1 01 00 08 30

Set

Sync on G

WHISPER

Get

06 00

68 D1

3B 23

AB 22

08 23

C7 F0

57 F1

A7 F1

F4 F0

C2 71

32 71

A2 70

91 70

02 00 08 30

01 00 00 33

02 00 00 33

01 00 A1 30

02 00 A1 30

01 00 09 22

02 00 09 22

01 00 12 30

NORMAL

WHISPER

Get

NORMAL

CINEMA

DYNAMIC

Get

Set

GAMMA

Large

Middle

Small

Get

Over Scan

Full

43 D6

Set

MyScreen Size

MyScreen Lock

06 00 D3 D7 01 00 12 30

06 00 70 D6 02 00 12 30

Get

off

06 00 3B EF 01 00 C0 30

06 00 AB EE 01 00 C0 30

Get

06 00

06 00 C2 FF 02 00 90 10

06 00 C2 F0 02 00 A0 10

08 EF

02 00 C0 30

Lamp Time

Filter Time

Get

BE EF

00 00

Download from Www.Somanuals.com. All Manuals Search And Download.

LCD Projector 28A8755B

USER'S MANUAL Vol.2 (Extended)

Thank you for purchasing this projector.

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct

usage through understanding. After reading, store this instruction manual in a

safe place for future reference.

NOTE

• The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without express

written authority.

TRADEMARK ACKNOWLEDGEMENT :

• PS/2, VGA and XGA are registered trademarks of the International Business Machines Corporation.

• Apple, Mac and ADB are registered trademarks of Apple Computer, Inc.

• VESA and SVGA are trademarks of the Video Electronics Standard Association.

• Windows is a registered trademark of Microsoft Corporation.

• All other trademarks are the property of their respective owners.

CONTENTS

Page

MULTIFUNCTIONAL SETTINGS ........................................................................2

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED ......7

SPECIFICATIONS .............................................................................................10

WARRANTY AND AFTER-SERVICE................................................................11

.......................................................................................

For "TECHNICAL" see the end of this manual.

Download from Www.Somanuals.com. All Manuals Search And Download.

MULTIFUNCTIONAL SETTINGS

This device has 6 separate menus: MAIN, PICTURE 1, PICTURE 2, INPUT,

SCREEN, OPTION. Each of these menus is operated using the same methods.

The basic operations of these menus are as follows.

Menu screen display : Press the MENU button.

Menu selection

: Choose a menu name using the

button, and press the

button or the ENTER button.

Item selection

: Choose an item using the

button or the ENTER button.

button, and press the

Return menu to last previous screen: Press the

button or the ESC button.

Execution of settings and/or adjustments Operate by using the

button. (For further

details, read the explanation for each separate menu.)

nitialization of settings and/or adjustments: During operation, press the RESET button.

(Note that items whose functions are

performed simultaneously with the operation

of clock phase, language selection, automatic

adjustment, etc., cannot be initialized.)

End menu operations: Press the MENU button, or do not perform any operation for

several seconds.

MAIN

BRIGHT

CONTRAST

ASPECT

PICT. POSIT.

GAMMA

MIRROR

MAIN Menu

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

With the MAIN menu, the seven items shown in the Table below can be

performed.

LANGUAGE

Perform each operation in accordance with the instructions in the Table.

: SELECT

Example : MAIN Menu

(BRIGHT)

MAIN Menu

Item

Description

Dark

BRIGHT

Adjust Brightness: Light

Adjust Contrast: Strong

CONTRAST

Weak

Select Aspect Ratio:

At RGB Input:

4:3

At VIDEO Input, S-VIDEO Input:

4:3 16:9

16:9

ASPECT

SMALL

• The SMALL picture may not be displayed correctly with certain input signals.

Select Picture Position (for 16:9/SMALL Picture):

PICT.POSIT.

GAMMA

TOP

CENTER

BOTTOM

DYNAMIC

V:INVERT

Select Gamma Mode:

NORMAL

CINEMA

Select Mirror Status:

MIRROR

NORMAL

H:INVERT

H&V:INVERT

Select Menu Language:

ENGLISH

FRANÇAIS

ITALIANO

POTUGUÊS

DEUTSCH

NEDERLANDS

ESPAÑOL

LANGUAGE

NORSK

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN

COLOR BAL R

COLOR BAL B

SHARPNESS

COLOR

PICTURE 1 Menu

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

TINT

With the PICTURE 1 menu, the five items shown in the Table

below can be performed.

Perform each operation in accordance with the instructions in the

Table.

: SELECT

Example : PICTURE1 Menu

(COLOR BAL R)

PICTURE1 Menu

Item

Description

COLOR BAL R

Adjust Red Color Balance: Dark

Light

COLOR BAL B

SHARPNESS

Adjust Blue Color Balance: Dark

Adjust Sharpness (for VIDEO/S-VIDEO): Clear

Soft

Adjust COLOR (for VIDEO/S-VIDEO):

COLOR

TINT

Dark

Light

Adjust Tint (for VIDEO/S-VIDEO): Green

Red

MAIN

V POSITION

H POSITION

H PHASE

PICTURE 2 Menu

PICTURE-1

PICTURE-2

INPUT

H SIZE

SCREEN

OPTION

OVER SCAN

With the PICTURE 2 menu, the five items shown in the Table

below can be performed.

Perform each operation in accordance with the instructions in the

Table.

: SELECT

Example : PICTURE2 Menu

(V POSITION)

PICTURE2 Menu

Item

Description

V POSITION

H POSITION

Adjust Vertical Position (for RGB): Up

Down

Right

Adjust Horizontal Position (for RGB): Left

Adjust Horizontal Phase (for RGB):

H PHASE

H SIZE

Right

Left

• Adjust to eliminate flicker.

Adjust Horizontal Size (for RGB): Large

• If the horizontal size adjustment is excessive, the image may not be displayed

correctly. In such a case, initialize H SIZE with the RESET button.

Small

Select Over-scan Ratio (for VIDEO/S-VIDEO):

LARGE

MIDDLE

SMALL

OVER SCAN

• It is recommended to select SMALL to avoid flicker at the lower part of the

picture.

Download from Www.Somanuals.com. All Manuals Search And Download.

MULTIFUNCTIONAL SETTINGS (continued)

MAIN

PICTURE-1

PICTURE-2

INPUT

AUTO

VIDEO

SYNC ON G

EXECUTE

INPUT Menu

SCREEN

OPTION

With the INPUT menu, the four items shown in the Table below can be

performed. With inputting of RGB IN 1 and RGB IN 2 signals, the

horizontal and vertical frequencies of the signals will be displayed on the

: SELECT

Example : INPUT Menu

(AUTO)

initial screen of the INPUT menu.

Perform each operation in accordance with the instructions in the Table.

INPUT Menu

Item

Description

Auto Adjust (for RGB): Automatically adjusts H POSITION, V POSITION, H

PHASE, and H SIZE. Use this function with the maximum window size.

Auto Adjust (for VIDEO/S-VIDEO): Automatically selects the proper VIDEO

mode for the current input signal. This function is active only when the AUTO

mode is selected for the item VIDEO. Refer to the description for the item

VIDEO below.

AUTO

• This function may not be available with a PAL60 signal and certain other

signals.

• The AUTO mode operation requires approximately 10 seconds.

Select Mode of Signal Type (for VIDEO/S-VIDEO):

AUTO

NTSC4.43

NTSC

M-PAL

PAL

N-PAL

SECAM

Selecting AUTO mode activates and performs the AUTO function for VIDEO/S-

VIDEO. It automatically selects the proper mode from among those above.

Use this function if the image becomes unstable with VIDEO/S-VIDEO. (e.g.

The image becomes irregular, or lacks color.)

VIDEO

• AUTO mode may not function correctly with a PAL60 signal and certain other

signals.

• The AUTO mode operation requires approximately 10 seconds.

On/Off SYNC ON G Mode:

TURN ON

TURN OFF

Selecting TURN ON turns on the SYNC ON G mode. The SYNC ON G mode

allows reception of SYNC on G.

SYNC ON G

• In the SYNC ON G mode, the picture may be distorted with certain input

signals. In such a case, remove the signal connector so that no signal is

received and turn SYNC ON G off, and then reconnect the signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN

BLANK

START UP

MyScreen

MyScreen Size

MyScreen Lock

MyScreen

ORIGNAL

SCREEN Menu

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

With the SCREEN menu, the five items shown in the Table below can be performed.

Please perform each operation in accordance with the instructions in the Table.

: SELECT

Example : SCREEN Menu

(BLANK)

SCREEN Menu

Item

Description

Selection of BLANK Screen:

MyScreen

ORIGINAL

The BLANK Screen may be voluntarily selected. The BLANK Screen is displayed when the screen

has been erased (i.e., made to vanish) by manipulating the BLANK button (please refer to the

“Temporarily Blanking the Screen” section of the separate booklet, Vol. 1 (Basic)).

MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen

(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.

ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).

Option screens: Various colored non-patterned (plain) screens displayed within the Menus.

• The MyScreen and the ORIGINAL Screen will each change to a non-patterned (plain) black color

screen several minutes after being displayed.

BLANK

Selection of START UP Screen:

MyScreen

ORIGINAL

TURN OFF

The START UP Screen may be voluntarily selected. The START UP Screen is displayed when

no signal has been inputted, or when spec signals are being inputted.

MyScreen: Using the MyScreen category (see this Table, below), one can register a desired screen

(or screens). At the time of factory shipment, this is set as a non-patterned (plain) blue color screen.

ORIGINAL: Existing standard screens. Please make confirmation using the actual screen(s).

TURN OFF: A non-patterned (plain) blue color screen.

START UP

•

The MyScreen and ORIGINAL screens will switch to the BLANK screen (see above in this

table) a few minutes after being displayed. If the BLANK screen is the MyScreen or

ORIGINAL screen, it will turn immediately to a solid black screen.

Registration of MyScreen:

When this item is executed, the MyScreen Menu for registration of MyScreen for the BLANK Screen

and the START UP Screen is displayed. When operations are performed in accordance with this Menu,

one can “cut” and register desired screens from among the received images within the display.

1. After the “Do you start capturing this picture?” message has been displayed, pressing the ESC (or

RESET) button interrupts execution of the MyScreen. When the ENTER button is pressed, the

picture becomes static (no longer moves), and a frame for picture cutting, as well as the message

that follows below, appear. Please press the button when the screen you want to register is

currently being displayed.

MyScreen

2. When the “Move the capture area as you want.” message has been displayed, pressing the ESC (or RESET)

button will eliminate the static state of the picture, and operations can be performed again from operation 1.

The frame can be moved using the

buttons. After designating the screen

you want to register, pressing the ENTER button will initiate screen registration. The registration

process takes approximately 1 minute to complete.

3. When the registration has been completed, the screen of the registered MyScreen, plus the

message, “MyScreen registration is finished,” will be displayed for several seconds, after which

the operation is terminated.

Selection of MyScreen display size:

MyScreen Size

MyScreen Lock

FULL

Invalidation of MyScreen registration function:

TURN ON

TURN OFF

When TURN ON is selected, the MyScreen category (see this Table, above) cannot be executed; in

this way, one can prohibit rewrites (“writeovers”) of the MyScreen.

Download from Www.Somanuals.com. All Manuals Search And Download.

MULTIFUNCTIONAL SETTINGS (continued)

MAIN

PICTURE-1

PICTURE-2

INPUT

SCREEN

OPTION

VOLUME

OPTION Menu

AUTO OFF

WHISPER

LAMP TIME

FILTER TIME

With the OPTION menu, the five items shown in the Table below

can be performed.

Please perform each operation in accordance with the instructions

in the Table.

: SELECT

Example : OPTION Menu

(VOLUME)

OPTION Menu

Item

Description

VOLUME

Adjust Volume: High

Low

Adjust AUTO OFF Time:

Long (MAX. 99 min.)

Short (Min. 1 min.)

(DISABLE: 0 min.)

AUTO OFF

WHISPER

The system automatically enters the standby mode if no signal is received

within the set time. This function is inactive when DISABLE (0 min.) is selected.

Select WHISPER Mode:

NORMAL

When WHISPER is selected the WHISPER mode is activated. In the WHISPER

mode, acoustic noise and screen brightness are reduced.

WHISPER

Refer to LAMP TIME: When set, this function displays the total time the

projector lamp has been used since new.

Reset LAMP TIME [Use this function only when the lamp has been replaced!]:

Depress the RESET button for at least 3 seconds while lamp time is being

displayed. The reset menu will then appear. After you replace the lamp with a

LAMP TIME

new lamp, select RESET on the menu with the

button.

• Do not reset the lamp time unless you have replaced the lamp. And, always

reset the lamp time when replacing the lamp. The message functions will not

operate properly if the lamp time is not reset correctly.

• Before replacing the lamp, carefully read the descriptions headed "THE

LAMP".

Refer to FILTER TIME: This function displays the total time the air-filter has

been used since new.

Reset FILTER TIME [Use this function only when the filter is cleaned or replaced!]:

Depress the RESET button for at least 3 seconds while filter time is being

displayed. The reset menu will then appear. After you replace the filter, select

FILTER TIME

RESET on the menu with the

button.

• Do not reset the filter time unless you have cleaned or replaced the filter. And,

always reset the filter time when cleaning or replacing the filter. The message

functions will not operate properly if the filter time is not reset correctly.

•

Before cleaning or replacing the filter, carefully read the descriptions headed "THE AIR FILTER".

Download from Www.Somanuals.com. All Manuals Search And Download.

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED

Related Messages

When the unit's power is ON, messages such as those shown below may be displayed. When

any such message is displayed on the screen, please respond as described below.

Message

Description

CHANGE THE LAMP

Lamp usage time is approaching 2,000 hours. (Note 2)

Preparation of a new lamp, and an early lamp change, is

recommended. After you have changed the lamp, please be

sure to reset the lamp timer.

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

(Note 1)

Lamp usage time is approaching 2,000 hours. A lamp change

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

within

hours is recommended. (Note 2)

When lamp usage reaches 2,000 hours, the power will

automatically be turned OFF. Please change the lamp by

referring to “THE LAMP” in Vol.1 (Basic). After you have

changed the lamp, please be sure to reset the lamp

timer.

THE POWER WILL TURN OFF

AFTER

hr.

(Note 1)

As lamp use has reached 2,000 hours, the power will soon be

automatically turned OFF. (Note 2)

CHANGE THE LAMP

Please immediately turn the power OFF, and follow the

instructions in the “THE LAMP” section of the separate booklet,

Vol.1 (Basic).

After you have changed the lamp, please be sure to reset the

lamp timer.

AFTER REPLACING LAMP,

RESET THE LAMP TIMER.

THE POWER WILL TURN OFF

AFTER 0 hr.

A note of precaution when cleaning the air filter.

After cleaning the filter, operate FILTER TIME of the OPTION

Menu, and perform reset of the filter timer.

CLEAN THE AIR FILTER

AFTER CLEANING AIR FILTER,

RESET THE FILTER TIMER.

There is no input signal.

Please confirm the signal input connection, and the status of the

signal source.

NO INPUT IS DETECTED

The horizontal or vertical wavelength of the inputted signal is

outside of the response parameters of this unit. Please confirm

the specs for this unit or the signal source specs.

SYNC IS OUT OF RANGE

kHz

The internal portion temperature is rising. Please turn the power

OFF, and allow the unit to cool down for approximately 20

minutes. After having confirmed the following items, then please

resent the power to ON.

CHECK THE AIR FLOW

•

Is there blockage of the air passage aperture?

Is the air filter dirty?

Does the peripheral temperature exceed 35°C?

NOTES

Note 1: Although this message will be automatically disappeared after around 3 minutes, it will be

reappeared every time the power is turned ON.

Note 2: Lamps have a finite product life. Lamps are characterized by the fact that, after long hours of

usage, a lamp will no longer light up, or the lamp will break or burst, etc. This unit is equipped

with an automatic shut-down function, such that the power will automatically be turned OFF

when lamp usage time has reached 2,000 hours. Please be aware, however, that among lamp

types, there are major differences in product lifetimes; a lamp may thus fail to light even prior

to the functioning of the automatic shut-down function of this unit.

Download from Www.Somanuals.com. All Manuals Search And Download.

Regarding the Indicator Lamps

Lighting and flashing of the POWER indicator, the LAMP indicator, and the

TEMP indicator have the meanings as described in the Table below.

Please respond in accordance with the instructions within the Table.

POWER

LAMP

TEMP

Description

indicator indicator indicator

The orange

Turned OFF Turned OFF

The STANDBY mode is set

lamp is lighted (Not lighted) (Not lighted)

Flashing of the green lamp

The green lamp is lighted

Flashing of the orange lamp

Turned OFF

The unit is warming up. Please wait.

The unit is in an ON state. Ordinary operations may be performed.

The unit is cooling down. Please wait.

Blinking of the

red lamp

A certain error has been detected. Wait until the POWER indicator lamp has finished

flashing, and then perform the proper response measure using the item descriptions

below as reference.

The lamp does not light.

There is a possibility that the interior portion has become heated. Turn the power OFF and wait

approximately 20 minutes. After the main unit has cooled down, please confirm whether or not

there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or

not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,

turn the power ON again; if the same display is displayed, then please change the lamp.

The red lamp

is lighted, or

blinks

The red lamp

is lighted

Turned

OFF

Either there is no lamp and/or lamp cover, or either of these has not been properly fixed

(attached). Turn the power OFF and wait approximately 45 minutes. After the main unit has

sufficiently cooled down, please make confirmation of the attachment state of the lamp and

lamp cover. After performing any needed maintenance, turn the power ON again; if the same

display is displayed, then please contact a sales store or a service company.

The red lamp

is lighted, or

blinks

Blinking of the

red lamp

Turned

OFF

The cooling fan is not operating. Turn the power OFF and wait approximately 20 minutes. After the

main unit has cooled down, please make confirmation that no foreign matter has become caught in

the fan, etc. After performing any needed maintenance, turn the power ON again; if the same display

is displayed, then please contact a sales store or a service company.

The red lamp

is lighted, or

blinks

Blinking of the

red lamp

Turned

OFF

There is a possibility that the interior portion has become heated. Turn the power OFF and wait

approximately 20 minutes. After the main unit has cooled down, please confirm whether or not

there is blockage of the air passage aperture, whether or not the filter is dirty, and/or whether or

not the peripheral temperature exceeds 35°C, etc. After performing any needed maintenance,

turn the power ON again; if the same display is displayed, then please contact a sales store or a

service company.

The red lamp is

lighted, or

blinks

The red lamp is

lighted

Turned

OFF

There is a possibility that the interior portion has become overcooled. Please use the unit within

the usage temperature parameters (0°C to 35°C). After performing any needed maintenance,

turn the power ON again; if the same display is displayed, then please contact a sales store or a

service company.

The green lamp

is lighted

Alternative blinking

with the red lamp

This is a notification that it is time to clean the filter.

After cleaning the filter, operate the FILTER TIME portion of the OPTION Menu, and perform

reset of the FILTER TIME.

The green

Simultaneous blinking

with the red lamp

lamp is lighted

NOTE

When the interior portion has become overheated, for safety purposes, the power source is automatically turned OFF,

and the indicator lamps may also be turned OFF. Press the “ ” (power OFF) side of the main power switch, and wait

for approximately 20 minutes. Please then use the unit only after having first confirmed that the unit has sufficiently

cooled down.

Download from Www.Somanuals.com. All Manuals Search And Download.

WHAT TO DO WHEN YOU THINK A MACHINE DEFECT HAS OCCURRED (continued)

Phenomena That May Easily Be Mistaken for Machine Defects

Before requesting repair, check in accordance with the following chart.

If the situation cannot be corrected, then contact your dealer.

Reference

Page(s)

Phenomenon

Cases not involving a machine defect

Items to be confirmed

The main power source is not ON.

Turn on the main power.

Vol.1-3, 14

The electrical power cord is not plugged in.

Correctly connect the power cord.

Be sure to press the “

of the main power switch, and leave this OFF

interrupted during operation, such as by for approximately 20 minutes. After the unit

O” (power OFF) side

Power does not

come ON

The main power source has been

Vol.1-14

a power outage (blackout), etc.

has sufficiently cooled down, turn ON the

power source.

The input changeover settings

are mismatched.

Select the input signal, and

correct the settings.

Vol.1-15

Vol.1-10, 11

Vol.1-17

Vol.1-10, 11

Vol.2-2

No sound or

pictures are

outputted

No signal is being inputted.

Correctly connect the connection cord.

Adjust the VOLUME setting to a higher level.

The electrical wiring to this unit

is not correctly connected.

Pictures are

displayed, but no

sounds are heard

The volume setting has been set at (or

adjusted to) an extremely low level.

Press the MUTE button to release

(change) the MUTE mode setting.

The MUTE mode is the current setting.

The electrical wiring to this unit

is not correctly connected.

Correctly connect the connection cord.

Sounds are

heard, but no

pictures are

displayed

The brightness setting has been set at Adjust the BRIGHT setting to a

(or adjusted to) an extremely low level.

brighter level.

The lens cap has not been removed.

Remove the lens cap.

Vol.1-14

Colors have a faded-

out appearance

Color tone is poor

Perform picture adjustments by changing the

COLOR BAL R, the COLOR BAL B, and/or the

TINT settings, etc.

Color depth setting or color tone setting

Vol.2-3

The brightness setting and/or contrast

setting has not been properly adjusted.

Perform picture adjustments by changing the

BRIGHT and/or CONTRAST settings, etc.

Vol.2-2

Vol.2-6

The WHISPER mode is the current Change (by releasing) from the

setting. WHISPER mode.

Pictures appear

dark

Lamp is approaching the end of its Exchange the old lamp with a new

Vol.1-25, 26

product lifetime.

Pictures appear Either the FOCUS setting or the H

PHASE is not properly adjusted.

lamp.

Vol.1-15

Vol.2-3

Adjust the FOCUS and H PHASE settings.

blurry

NOTE

Although bright spots or dark spots may appear on the screen, this is a unique characteristic of liquid crystal displays, and

such do not constitute or imply a machine defect.

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

NOTE • This specifications are subject to change without notice.

Item

Specification

Product name

Liquid crystal projector

1.8 cm (0.7 type)

Panel size

Liquid

crystal

panel

Drive system

TFT active matrix

ED-S3170A 480,000 pixels (800 horizontal x600 vertical)

ED-X3270A 786,432 pixels (1024 horizontal x 768 vertical)

Pixels

Lens

Zoom lens F=1.7 ~ 1.9 f=21.7 ~ 26.1 mm

Lamp

150 W UHB

Speaker

1.0W

Power supply

Power consumption

Temperature range

Size

AC100 ~ 120V, 2.7A / AC220 ~ 240V, 1.3A

240W

0 ~ 35°C (Operating)

295 (W) x 87.5 (H) x237 (D) mm

2.7 kg

Weight (mass)

RGB Ports

RGB OUT Ports

RGB IN(1, 2) ..................2

VIDEO Ports

RGB OUT........................1

AUDIO OUT Ports

VIDEO IN ........................1

S-VIDEO IN ....................1

AUDIO Ports

AUDIO IN(1,2) ................2

AUDIO IN(R, L) ..............1

AUDIO OUT....................1

CONTROL Ports

CONTROL ......................1

USB ................................1

Ports

Lamp:=DT00521

Air Filter: MU01691

Optional Parts

* For others, consult your dealer.

Dimension Diagram

295

77.5

Unit : mm

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY AND AFTER-SERVICE

If a problem occurs with the equipment, first refer to the 7 “WHAT TO DO WHEN YOU

THINK A MACHINE DEFECT HAS OCCURRED” section and run through the suggested

checks. If this does not resolve the problem contact your dealer or service company. They

will tell you what warranty condition is applied.

Download from Www.Somanuals.com. All Manuals Search And Download.

DUKANE CORPORATION

FIVE-YEAR LIMITED WARRANTY

This Dukane projector is warranted to the original purchaser for a period of five (5) years from

the original purchase date – in normal operating conditions – against defects in material and

workmanship . DUKANE CORPORATION EXPRESSLY DISCLAIMS ALL OTHER

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

DURING THE WARRANTY PERIOD, DUKANE CORPORATION’S LIABILITY FOR ANY

DEFECTIVE PRODUCT (except for the lamp, which is subject to whatever warranties the

manufacturer may provide) IS LIMITED TO THE REPAIR OR REPLACEMENT OF

PRODUCT AT DUKANE CORPORATION’S OPTION. REPLACEMENT PRODUCTS MAY

BE NEW OR USED (used units will not exceed hours of defective unit). The following are not

covered by the limited warranty and Dukane Corporation shall not be liable for:

1. Any product which is not distributed in the U.S.A. or Canada by Dukane Corporation or an

authorized dealer.

2. Normal decrease in lamp light output over time.

3. Damage, deterioration or malfunction resulting from:

Accident, misuse, abuse, neglect, improper ventilation, fire, dust, smoke, water, lighting

or other acts of nature, unauthorized product modification, or failure to follow

instructions supplied with the product (including proper maintenance of air filters).

Repair or attempted repair by anyone other than a Dukane Corporation authorized service

center.

Any shipment of product (claims must be presented to the carrier).

Removal or installation of the product.

Any other causes which do not relate to a product defect.

Use of the product beyond normal operating conditions. Normal operating conditions are

defined as product use not in excess of 8 hours per day and 260 days per year.

4. Cartons, carry cases, shipping cases, batteries, or any accessories used in connection with the

product.

5. Service required as a result of third party components.

6. Product used as commercial rental units

Dukane corporation will pay labor and material expenses for covered items, but Dukane

Corporation will not pay for the following:

1. Removal or installation charges.

2. Cost of technical adjustment, set-up, maintenance, or adjustment of user controls.

3. Payment of shipping and related charges incurred in returning the product for warranty

repair.

Dukane Corporation disclaims all liability for incidental or consequential damage of any kind,

including all damages arising out of any interruptions in operation of the product and all damages

to software.

No person, firm, or representative is authorized to assume any obligation or to make any warranty

on behalf of the Dukane Corporation other than as stated above.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Visual Products

Dukane Corporation

Audio Visual Products Division

2900 Dukane Drive

St. Charles, IL 60174-3395

E-mail: avsales@dukcorp.com

Phone: (630) 584-2300

Orders: (800) 676-2485

Information: (800) 676-2486

Fax: (630) 584-5156

Parts & Service: (800) 676-2487

Fax: (630) 584-0984

Download from Www.Somanuals.com. All Manuals Search And Download.

Part # 401-8755B-00

Code Alarm Automobile Alarm CA 120 User Manual
Cornelius Juicer QUEST 4000 User Manual
Craftsman Lawn Mower Accessory 358792443 User Manual
Crane Humidifier EE 3184 4138 User Manual
Crate Amplifiers Musical Instrument Amplifier KX 50 User Manual
Delfield Refrigerator SAR User Manual
Dukane Projector 8918 User Manual
Electro Voice Portable Speaker DMC 2181X User Manual
Estate Microwave Oven W10131995A User Manual
GE Monogram Ventilation Hood ZXR8510 User Manual