Data Video Projector
User’s Manual (Concise)
MODELS 8104WB/8105B/8106B
Information in this Guide may change due to product improvements. To obtain the latest
and look at the specific model SUPPORT or DOWNLOADS section.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
430-8104WB-8105B-8106B-Concise-00
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Projector
CP-A222WN/8105B, CP-A302WN/8106B, CP-AW252WN/8104WB
User's Manual (concise)
Thank you for purchasing this projector.
Please read through this manual before using this product, in order to use safely
and utilize well the product.
WARNING ►Before using this product, be sure to read all manuals for this
(
19)
to read the manuals in the CD.
product. See the “Using the CD manual” ꢀ
After reading them, store them in a safe place for future reference.
►Heed all the warnings and cautions in the manuals or on the product.
►Follow all the instructions in the manuals or on the product.
NOTE • In this manual, unless any comments are accompanied, “the
manuals” means all the documents provided with this product, and “the product”
means this projector and all the accessories came with the projector.
Contents
ꢀ
ꢀ
First of all............................................ 2 Turning on the power........................ 11
Entries and graphical symbols explanation......2
Important safety instruction ..............................2
Adjusting the projector's elevator ..... 12
Operation.......................................... 12
Regulatory notices.............................. 3 Turning off the power........................ 14
About Electro-Magnetic Interference................
About Waste Electrical and Electronic Equipment...4
3
Replacing the lamp........................... 15
Cleaning and replacing the air filter.. 17
Contents of package........................... 4 Caring for the mirror and lens........... 18
Arrangement....................................... 5 Using the CD manual ....................... 19
Connecting with your devices............. 6 Specifications ................................... 20
Connecting power supply................... 8 Troubleshooting
Using the cable cover......................... 9
Preparing for the remote control....... 10
- Warranty and after-service........... 21
1
Download from Www.Somanuals.com. All Manuals Search And Download.
First of all
Entries and graphical symbols explanation
The following entries and graphical symbols are used for the manuals and the
product as follows, for safety purpose. Please know their meanings beforehand,
and heed them.
WARNING This entry warns of a risk of serious personal injury or even death.
CAUTION This entry warns of a risk of personal injury or physical damage.
NOTICE This entry notices of fear of causing trouble.
Important safety instruction
The followings are important instructions for safely using the product. Be sure to
follow them always when handling the product. The manufacturer assumes no
responsibility for any damage caused by mishandling that is beyond normal usage
defined in these manuals of this projector.
WARNING ►Never use the product in or after an abnormality (ex. giving
off smoke, smelling strange, took a liquid or an object inside, broken, etc.) If an
abnormality should occur, unplug the projector urgently.
►Situate the product away from children and pets.
►Do not use the product when there is fear of a thunderbolt.
►Unplug the projector from the power outlet if the projector is not used for the
time being.
►Do not open or remove any portion of the product, unless the manuals direct
it. For internal maintenance, leave it to your dealer or their service personnel.
►Use only the accessories specified or recommended by the manufacturer.
►Do not modify the projector or accessories.
►Do not let any things or any liquids enter to the inside of the product.
►Do not wet the product.
►
Do not place the projector where any oils, such as cooking or machine oil, are used.
Oil may harm the product, resulting in malfunction, or falling from the mounted
position.
►Do not apply a shock or pressure to this product.
- Do not place the product on an unstable place such as the uneven surface or
the leaned table.
- Do not place the product unstably. Place the projector so that it does not
protrude from the surface where the projector is placed on.
- Remove all the attachments including the power cord and cables, from the
projector when carrying the projector.
►
Never look into the projection lens or mirror while the projection lamp lights,
since the projection lamp ray may cause a trouble on your eyes.
►Do not approach the lamp cover and the exhaust vents, while the projection
lamp is on. Also after the lamp goes out, do not approach them for a while, since
too hot.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices
About Electro-Magnetic Interference
In CANADA
This Class B digital apparatus complies with Canadian ICES-003.
In the US, and other places where the FCC regulations are applicable
Declaration of Conformity
Trade name
HITACHI/Dukane
Model Number
CP-A222WN/8105B, CP-A302WN/8106B, CP-AW252WN/8104WB
Responsible Party Hitachi America, Ltd.
Address
900 Hitachi way, Chula Vista, CA 91914-3556 U.S.A.
Telephone Number +1 -800-448-2244
This device complies with part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
INSTRUCTIONS TO USERS: This equipment complies with the requirements of
FCC (Federal Communication Commission) equipment provided that the following
conditions are met. Some cables have to be used with the core set. Use the
accessory cable or a designated-type cable for the connection. For cables that
have a core only at one end, connect the core to the projector.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory notices (continued)
About Waste Electrical and Electronic Equipment
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries or accumulators included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury or more than, 0.002%
Cadmium, or more than 0.004% Lead.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
(1)
(5)
Contents of package
ASPECT
MAGNIFY
AUTO SEARCH BLANK
PAGE
UP
VOLUME
FREEZE
ON
㧗
OFF
DOWN
MY BUTTON
Your projector should come with the items
shown below. Check that all the items are
included. Require of your dealer immediately if
any items are missing.
KEYSTONE
ꢁ
MUTE
ꢀ
ꢂ
ꢃ
ꢂ D-ZOOM
ꢃ
FOCUS
POSITION
MENU
ENTER
ESC
RESET
(6)
(7)
(2)
(3)
(1) Remote control with the two AA batteries
(2) Power cord
(3) Computer cable
(4) Parts of cable cover
(5) User’s manuals (Book x1, CD x1)
(6) Security label
(7) Application CD
(8) Wall mount unit and User's manual *
(9) Adapter cover
(8) *
1
(4)
(9)
WARNING ►Do not attempt to install the projector yourself. Have your
dealer or service center handle all installation work. Note that manufacturer will
accept no liability whatsoever for accidents or injuries resulting from an incorrect
installation or improper use.
NOTE • Keep the original packing materials for future reshipment. Be sure
to use the original packing materials when moving the projector. Use special
caution for the lens.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrangement
Refer to tables T-1 or T-2 and figures F-1 and F-2 at the end of this manual to determine
the screen size and projection distance.
The values shown in the table are calculated for a full size screen.
a
b1 , b2
c1 c2
, Screen height ( 8%)
Screen size (diagonal)
Projection distance ( 8%)
• For the case of installation in special conditions such as on the wall or ceiling, the
specified mounting accessories (ꢀ20) and service may be required. Tabletop use must
be set up with the designated optional accessories (ꢀ20). Before installing the projector,
consult your dealer about your installation.
• The screen position may shift after installation if the projector is mounted on locations such
as the wall or ceiling, due to the flexibility of the plastic projector body. If readjustment is
necessary, consult with your dealer or service personnel.
• The projected image position and/or focus may change during warm-up (approx. 30
minutes after the lamp is turned on) or when the ambient conditions change. Readjust
the image position and/or focus as necessary.
• Since the projector features an ultra short throw, be aware that it is required to select a
screen carefully to have better performance.
- A soft screen such as a pull-down screen may cause serious distortion of a projected
image. A hard screen such as a board screen is recommended for use with this projector.
- A high-gain screen such as a bead screen that has narrow viewing angle is not suitable
for this projector. A low-gain screen (around 1.0) such as a matte screen that has wide
viewing angle is recommended for use with this projector.
-
A screen with a weave pattern may cause moiré on the projected image, which is not a failure
of the projector. A screen that has less moiré effects is recommended for use with this projector.
WARNING ►Install the projector in a stable horizontal position.
►Place the projector in a cool place, and ensure that there is sufficient ventilation.
Keep a space of 30 cm or more between the sides of the projector and other objects
such as walls. Do not place or attach anything that would block the lens or vent
holes. Do not place the projector where the air from an air conditioner or similar unit
will blow on it directly.
►Do not place the projector anyplace where it may get wet.
►
Use only the mounting accessories the manufacturer specified, and leave installing
and removing the projector with the mounting accessories to the service personnel.
►Read and keep the user's manual of the mounting accessories used.
CAUTION ►Avoid placing the projector in smoky, humid or dusty place.
►Position the projector to prevent light from directly hitting the projector’s remote sensor.
►If the projector is used at an altitude of about 1600 m or higher, set ALTITUDE of
the SERVICE item in the OPTION menu to HIGH. Otherwise, set it to NORMAL.
If the projector is used with a wrong setting, it may cause damage to the projector
itself or the parts inside.
•
The projector may make a rattling sound when tilted, moved or shaken,
NOTE
since a flap to control the air flow inside of the projector has moved. Be aware that
this is not a failure or malfunction.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Arrangement (continued)
Connecting with your devices
Be sure to read the manuals for devices before connecting them to the projector.
Make sure that all the devices are suitable to be connected with this product, and
prepare the cables required to connect. Refer to figures F-3 to F-5 at the back of
this manual.
For details, please see “User's Manual” - “Operating Guide” and “Network Guide”.
(
19, 21)
ꢀ
• When AUTO is selected for the COMPUTER IN1 or COMPUTER IN2 port in
COMPUTER IN of the INPUT menu, that port will accept component video signals.
• To use network functions of the projector, connect the LAN port with the
computer's LAN port, or with an access point that is connected to the computer
with wireless LAN, using a LAN cable.
•
If you insert a USB storage device, such as a USB memory, into the USB TYPE A
port and select the port as the input source, you can view images stored in the device.
• You can connect a dynamic microphone to the MIC port with a 3.5 mm mini-plug.
In that case, the built-in speaker outputs the sound from the microphone, even
while the sound from the projector is output.
WARNING ►Use only the appropriate accessories. Otherwise it could
cause a fire or damage to the device and the projector.
- Use only the accessories specified or recommended by the projector’s
manufacturer. Consult your dealer when the required accessory did not come
with the product or the accessory is damaged. It may be regulated under
some standard.
- For a cable with a core at only one end, connect the end with the core to the
projector. That may be required by EMI regulations.
- Neither disassemble nor modify the projector and the accessories.
- Do not use the damaged accessory. Be careful not to damage the
accessories. Route a cable so that it is neither stepped on nor pinched out.
CAUTION ►Do not turn on or off the projector while connected to a device
in operation, unless that is directed in the manual of the device.
►Be careful not to mistakenly connect a connector to a wrong port.
►Before connecting the projector to a network, be sure to obtain the consent of
the administrator of the network.
►Do not connect the LAN port to any network that might have the excessive
voltage.
►The designated USB wireless adapter that is sold as an option is required to
use the wireless network function of this projector.
►
Before removing the USB storage device from the port of the projector, be sure
to use the REMOVE USB function on the thumbnail screen to secure your data.
►Before you insert or pull out the USB wireless adapter from the projector, turn
off the power of the projector and pull out the power cord’s plug from the outlet.
Do not touch the USB wireless adapter while the projector is receiving AC power.
(continued on next page)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with your devices (continued)
NOTICE ►Use the cables with straight plugs, not L-shaped ones, as the input
ports of the projector are recessed.
NOTE • If a loud feedback noise is produced from the speaker, move the
microphone away from the speaker.
• This projector doesn't support plug-in power for the microphone.
•
The COMPUTER IN1/2 port can support a component signal also. The specific
adapter or the specific cable is required for a component video input to the projector.
Fastening the adapter cover
Use the supplied adapter cover to prevent the
USB wireless adapter (optional) from coming
off easily and prevention from burn injury.
1
Loosen the screw (marked with triangle)
1.
on the bottom left of the USB TYPE A port.
Insert the tab of the cover into the hole
2
2.
at the upper right of the USB TYPE A
port in the direction of the arrow.
3
Align the screw holes on the projector
3.
and the cover. Then insert the screw
removed from the projector into the hole
and tighten the screw.
Tab
WARNING ►Keep small parts away from children and pets. Take care not to
put in the mouth. Heat may build up in the USB wireless adapter, to avoid possible
burns disconnect the projector power cord for more than 5min. before touching it.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting power supply
Put the connector of the power cord into the
1.
2.
AC IN (AC inlet) of the projector.
Firmly plug the power cord’s plug into the
outlet. In a couple of seconds after the power
supply connection, the POWER indicator will
light up in steady orange.
AC IN
Power cord
Please remember that when the DIRECT POWER ON
function activated, the connection of the power supply make the projector turn on.
WARNING ►Please use extra caution when connecting the power cord, as
incorrect or faulty connections may result in fire and/or electrical shock.
• Do not touch the power cord with a wet hand.
• Only use the power cord that came with the projector. If it is damaged, consult
your dealer to get a new one. Never modify the power cord.
• Only plug the power cord into an outlet whose voltage is matched to the power
cord. The power outlet should be close to the projector and easily accessible.
Remove the power cord for complete separation.
• Do not distribute the power supply to multiple devices. Doing so may overload
the outlet and connectors, loosen the connection, or result in fire, electric shock
or other accidents.
NOTICE ►This product is also designed for IT power systems with a phase-
to-phase voltage of 220 to 240 V.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the cable cover
Utilize the cable cover as the guard and blind for the connecting parts.
Connect the signal cables and the power cord to the projector first.
1.
Combine parts as shown in figure,
2. and assemble the cable cover.
3
3
1
1
2
2
Insert the three knobs on the cable cover into the three holes on the projector
as shown in the figure. Pass the cables through the holes on the bottom of
3
.
the cable cover.
knobs
1
1
3
2
2
3
CAUTION ► Be careful not to pinch the cables in the cable cover, to
prevent damage to the cables.
► Use the cable cover that is supplied with the projector. Do not attempt any
modifications to the cable cover.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparing for the remote control
Please insert the batteries into the remote control before using it. If the remote
control starts to malfunction, try to replace the batteries. If you will not use the
remote control for long period, remove the batteries from the remote control and
store them in a safe place.
1
2
3
Holding the hook part of the battery
1. cover, remove it.
Align and insert the two AA batteries
2.
(HITACHI MAXELL or HITACHI MAXELL
ENERGY, Part No.LR6 or R6P) according to their plus and minus terminals as
indicated in the remote control.
Replace the battery cover in the direction of the arrow and snap it back into
place.
3.
Remote sensor
NOTE
• Try changing the batteries when the remote
control malfunctions.
• This remote control works with the remote
sensors on the projector using infrared light
(Class 1 LED). The active sensor senses
the remote control signal assigned within 60
degrees to right and left, and within 3 meters.
For details, see the Operating Guide in the CD.
• Prevent the remote sensors from being hit by
a strong ray. It may cause malfunction of the
projector and remote control.
30°
30°
3m
(approx.)
WARNING ►Always handle the batteries with care and use them only as
directed. Improper use may result in battery explosion, cracking or leakage,
which could result in fire, injury and/or pollution of the surrounding environment.
• Be sure to use only the batteries specified. Do not use batteries of different
types at the same time. Do not mix a new battery with used one.
•
Make sure the plus and minus terminals are correctly aligned when loading a battery.
• Keep a battery away from children and pets.
• Do not recharge, short circuit, solder or disassemble a battery.
•
•
Do not place a battery in a fire or water. Keep batteries in a dark, cool and dry place.
If you observe battery leakage, wipe out the leakage and then replace a battery.
If the leakage adheres to your body or clothes, rinse well with water immediately.
•
Obey the local laws on disposing the battery.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDBY/ON button
POWER indicator
Turning on the power
Make sure that the power cord is firmly
1.
and correctly connected to the projector
and the outlet.
Make sure that the POWER indicator is
2.
3.
steady orange.
Confirm that there is nothing that the
lens door hits while opening. Press the
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
MAGNIFY
AUTO SEARCH BLANK
PAGE
UP
VOLUME
㧗
FREEZE
ON
OFF
DOWN
MY BUTTON
KEYSTONE
ꢀ
ꢁ
MUTE
STANDBY/ON button on the projector or
the remote control. The lens door opens, the
projection lamp lights up, and the POWER
indicator begins to blink green. When the
FOCUS
ꢂ
ꢃ
ꢂ D-ZOOM
ꢃ
POSITION
MENU
ENTER
ESC
RESET
power is completely on, the indicator will stop blinking and light in steady green.
WARNING ►Never look into the projection lens or mirror while
the projection lamp lights, since the projection lamp ray may cause
a trouble on your eyes.
►Be careful not to pinch your finger with the lens door, to prevent an injury.
►Do not place the projector vertically with the lens door open
as shown in the figure on the right. It could cause malfunction or
injury. Tabletop use must be set up with the designated optional
accessories.
►Do not stand under the projector mounted on the wall or ceiling,
when its lens door is opening or closing. Moreover, do not look at
the mirror when the lens door is opening or closing.
►Never touch a lens door or mirror. If the mirror is broken, the
projected image will be distorted. Close the lens door, and contact
your dealer.
NOTE • Please power on the projector prior to the connected devices.
•
The projector has the DIRECT POWER ON function, which can make the projector
automatically turn on. For more information, please see the “Operating Guide” in the CD.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting the projector's elevator
The projector has Front foot for inclinations and Rear foot for horizontals. Spacers
on the each elevator foot are installed at the time of shipment, and projector is in a
condition to be able to just project. If necessary, detach the spacer, and the elevator
feet can be manually twisted to make more precise adjustments.
2.3~4.3°
Front foot
Rear foot
Front foot
Spacer (Large)
-1~1°
Spacer (Small)
Spacer
Rear foot
WARNING ►Keep the spacers away from children and pets. Be careful not
to let them swallow the spacers. If swallowed consult a physician immediately
for emergency treatment.
NOTE • The adjustment angle can be adjusted up to plus or minus 1° each
of Front and Rear foot.
•
After the foot is adjusted, it is possible to return it to the state of the shipment with a spacer.
Install Large on the Front foot and Small on the Rear foot of the spacer. If change
the setting place of the projector, it will recommend keep and reuse the spacers.
Operation
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
INPUT button
ASPECT
MAGNIFY
AUTO SEARCH BLANK
PAGE
UP
VOLUME
㧗
FREEZE
ON
COMPUTER button
VIDEO button
OFF
DOWN
FOCUS - button
FOCUS + button
MY BUTTON
KEYSTONE
ꢁ
MUTE
ꢀ
FOCUS
ꢂ
ꢃ
ꢂ D-ZOOM
ꢃ
POSITION
MENU
ENTER
ESC
RESET
Displaying and switching the image
Press the INPUT button on the projector. Each time you press the button, the
projector switches its input port in turn. You can also use the remote control to
select an input signal. Press the VIDEO button for selecting an input signal from
the HDMI, S-VIDEO or VIDEO port, or the COMPUTER button for selecting an
input signal from the COMPUTER IN1, COMPUTER IN2, LAN, USB TYPE A or
USB TYPE B port.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Focusing
ASPECT button
Use the FOCUS + and FOCUS - buttons on
the projector or remote control to adjust the
screen focus.
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
ASPECT
MAGNIFY
AUTO SEARCH
PAGE
BLANK
VOLUME
VOLUME +/- button
FREEZE
UP
ON
㧗
OFF
DOWN
KEYSTONE button
MUTE button
Selecting an aspect ratio
MY BUTTON
KEYSTONE
ꢁ
MUTE
ꢀ
ꢂ D-ZOOM
ꢃ
FOCUS
ꢃ
ꢂ
Each time you press the ASPECT button on
the remote control, it switches the aspect
ratio of the image, in turn.
POSITION
MENU
D-ZOOM + button
D-ZOOM - button
ENTER
ESC
RESET
Zooming
FOCUS + button
FOCUS - button
Use the D-ZOOM + and D-ZOOM - buttons
on the remote control to adjust the screen size.
POSITION button
Adjusting the picture position
After pressing the POSITION button on the remote control, use the ▲, ▼, ◄ and
► buttons. Press the POSITION button again to finish this operation.
Correcting distortion
Press the KEYSTONE button on the remote control. A dialog will appear on the
screen to aid you in correcting the distortion.
Use the ▲/▼ cursor buttons to select, MANUAL or PERFECT FIT operation, and
press the ► button to perform the following.
MANUAL displays a dialog for keystone correction.
PERFECT FIT displays a dialog for adjusting the shape of the projected image in
each of the corners and sides.
Use the cursor buttons according to the dialog, checking the image.
Press the KEYSTONE button again to finish this operation.
Adjusting the volume
Use the VOLUME +/- buttons to adjust the volume.
Muting the sound
Press the MUTE button on the remote control. To restore the sound, press the
MUTE or VOLUME +/- button.
CAUTION ►If you wish to have a blank screen while the projector's lamp is
on, use the BLANK function (see the Operating Guide).
Any other method of blocking the projection light, such as attaching something
to the lens or placing something in front of the lens, may cause the damage to
the projector.
NOTE • The ASPECT button does not work when no proper signal is inputted.
• For details, see the Operating Guide in the CD.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Turning off the power
STANDBY/ON button
POWER indicator
Press the STANDBY/ON button on the
1.
projector or the remote control.
The message “Power off?” will appear on
the screen for about 5 seconds.
Confirm that there is nothing that the
2.
lens door hits while closing. Press the
MY SOURCE/
VIDEO COMPUTER DOC.CAMERA
STANDBY/ON button again while the
message appears.
ASPECT
MAGNIFY
AUTO SEARCH BLANK
PAGE
UP
VOLUME
FREEZE
ON
㧗
OFF
DOWN
MY BUTTON
KEYSTONE
ꢀ
ꢁ
MUTE
FOCUS
ꢂ
ꢃ
ꢂ D-ZOOM
ꢃ
The projector lamp will go off, and the
POWER indicator will begin blinking in
orange. The lens door will close right after the
lamp goes off.
POSITION
MENU
ENTER
ESC
RESET
However, to maintain better picture quality, the lens door will close after the
lamp has been cooled down when the projector is installed upside down such
as in ceiling mount installation. Then the POWER indicator will stop blinking
and light in steady orange when the lamp cooling is complete.
Do not turn the projector on for about 10 minutes or more after turning it off.
Also, do not turn the projector off shortly after turning it on. Such operations might
cause the lamp to malfunction or shorten the lifetime of some parts including the lamp.
WARNING ►Be careful not to pinch your finger with the lens door, to
prevent an injury.
►Do not touch around the lamp cover and the exhaust vents during use or just
after use, since it is too hot.
►Remove the power cord for complete separation. The power outlet should be
close to the projector and easily accessible.
NOTE • Please power off the projector after any connected devices are
powered off.
• This projector has the AUTO POWER OFF function that can make the
projector turn off automatically. For more information, please see the “Operating
Guide” in the CD.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp
A lamp has finite product life. Using the lamp for long periods of time could cause
the pictures darker or the color tone poor. Note that each lamp has a different
lifetime, and some may burst or burn out soon after you start using them.
Preparation of a new lamp and early replacement are recommended. To prepare
a new lamp, make contact with your dealer and tell the lamp type number.
Type number : 456-8105B
lamp cover
Turn the projector off, and unplug the power cord.
1. Allow the projector to cool for at least 45 minutes.
Prepare a new lamp. If the projector is mounted
2. on a wall or ceiling, or if the lamp has broken, also
ask the dealer to replace the lamp.
In case of replacement by yourself, follow the
following procedure.
Loosen the screw (marked by arrow) of the lamp
3. cover and then slide and lift the lamp cover to the
side to remove it.
Loosen the 2 screws (marked by arrow) of the
4. lamp, and slowly pick up the lamp by the handle.
Never loosen any other screws.
Insert the new lamp, and retighten firmly the
5.
2 screws of the lamp that are loosened in the
previous process to lock it in place.
While putting the interlocking parts of the lamp
6.
cover and the projector together, slide the lamp
cover back in place. Then firmly fasten the screw
of the lamp cover.
Turn the projector on and reset the lamp time
7.
using the LAMP TIME item in the OPTION menu.
(1) Press the MENU button to display a menu.
(2) Point at the ADVANCED MENU in the menu using
the ▼/▲ button, then press the ► button.
(3) Point at the OPTION in the left column of the menu
using the ▼/▲button, then press the ► button.
Handle
(4) Point at the LAMP TIME using the ▼/▲ button, then
press the ► button. A dialog will appear.
(5) Press the ► button to select “OK” on the dialog. It performs resetting the lamp
time.
CAUTION ►Do not touch any inner space of the projector, while the lamp
is taken out.
NOTE • Please reset the lamp time only when you have replaced the lamp,
for a suitable indication about the lamp.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the lamp (continued)
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
WARNING ►The projector uses a high-pressure mercury glass lamp. The lamp
can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or
worn over time. Note that each lamp has a different lifetime, and some may burst or
burn out soon after you start using them. In addition, if the bulb bursts, it is possible
for shards of glass to fly into the lamp housing, and for gas containing mercury and
dust containing fine particles of glass to escape from the projector’s vent holes.
►About disposal of a lamp: This product contains a mercury lamp; do not put
it in a trash. Dispose of it in accordance with environmental laws.
• For product disposal, consult your local government agency
For more information, ask your dealer.
• If the lamp should break (it will make a loud bang when it does),
unplug the power cord from the outlet, and make sure to request a
replacement lamp from your local dealer. Note that shards of glass
could damage the projector’s internals, or cause injury during handling,
so please do not try to clean the projector or replace the lamp yourself.
Disconnect
• If the lamp should break (it will make a loud bang when it does), ventilate the
the plug
room well, and make sure not to inhale the gas or fine particles that come out
from the
from the projector's vent holes, and not to get them into your eyes or mouth.
power
• Before replacing the lamp, turn the projector off and unplug the power
outlet
cord, then wait at least 45 minutes for the lamp to cool sufficiently.
Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.
•
Do not open the lamp cover while the projector is mounted on a wall or ceiling.
This is dangerous, since if the lamp’s bulb has broken, the shards will fall out
when the cover is opened. In addition, working in high places is dangerous, so
ask your local dealer to have the lamp replaced even if the bulb is not broken.
• Do not use the projector with the lamp cover removed. At the lamp
replacing, make sure that the screws are screwed in firmly. Loose
screws could result in damage or injury.
• Use only the lamp of the specified type. Use of a lamp that does not
meet the lamp specifications for this model could cause a fire, damage or
shorten the life of this product.
• If the lamp breaks soon after the first time it is used, it is possible
that there are electrical problems elsewhere besides the lamp. If this
happens, consult your local dealer or a service representative.
•
Handle with care: jolting or scratching could cause the lamp bulb to burst during use.
• Using the lamp for long periods of time, could cause it dark, not to light
up or to burst. When the pictures appear dark, or when the color tone
is poor, please replace the lamp as soon as possible. Do not use old
(used) lamps; this is a cause of breakage.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and replacing the air filter
The air filter has two kinds of filters inside. Please check and clean the air filter periodically.
When the indicators or a message prompts you to clean the air filter, comply with it as soon
as possible. If the filters are damaged or heavily soiled, replace them with the new ones. To
prepare the new filters, make contact with your dealer and tell the following type number.
Type number : UX37191 (Filter set)
When you replace the lamp, please replace the air filter. An air filter of specified type will
come together with a replacement lamp for this projector.
3.
Turn the projector off, and unplug the power cord. Allow
1.
the projector to sufficiently cool down.
Use a vacuum cleaner on and around the filter cover.
2.
Filter cover
Slide the filter unit upward to take it off from the projector.
3.
Use a vacuum cleaner for the filter vent of the projector.
4.
Take the fine meshed filter out while holding the filter
5.
cover. It is recommended to leave the coarse meshed
Intake vent
filter in the filter cover as it is.
Filter unit
Filter cover
Use a vacuum cleaner on both sides of the fine meshed
filter while holding it so it will not be sucked in. Use a
vacuum cleaner for the inside of the filter cover to clean
up the coarse meshed filter. If the filters are damaged
or heavily soiled, replace them with new ones.
7.
6.
Put the fine meshed filter on the coarse meshed one,
turning its stitched side up.
7.
8.
9.
Filter
(coarse meshed)
Filter (fine meshed)
Put the filter unit back into the projector.
Stitched
side
Turn the projector on and reset the filter time using the
FILTER TIME item in the EASY MENU.
(1) Press the MENU button to display a menu.
(2) Point at the FILTER TIME using the ▼/▲ button, then press
the ► button. A dialog will appear.
(3) Press the ► button to select “OK” on the dialog. It performs resetting the filter time.
WARNING ►Before taking care of the air filter, make sure the power cable
is not plugged in, then allow the projector to cool sufficiently.
►
Use only the air filter of the specified type. Do not use the projector without the
air filter or the filter cover. It could result in a fire or malfunction to the projector
.
►Clean the air filter periodically. If the air filter becomes clogged by dust or the like,
internal temperatures rise and could cause a fire, a burn or malfunction to the projector.
NOTE • Please reset the filter time only when you have cleaned or replaced
the air filter, for a suitable indication about the air filter.
• The projector may display the message such as the “CHECK THE AIR FLOW”
or turn off the projector, to prevent the internal heat level rising.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the mirror and lens
If the projection mirror or lens is flawed, soiled or fogged, it could cause deterioration
of display quality. Please take care of the mirror and lens, being cautious of handling.
Turn the projector off and unplug the power cord
1.
from the power outlet. And cool the projector down
by leaving it for a while as it is.
The lens door can be opened manually.
2.
Please hold both side of the lens door and slowly
open it until it is locked with clicking sound.
Use an air blower to blow away dust on the lens
3.
and on the mirror before wiping. Wipe softly the
mirror and lens with a damped soft cleaning cloth
for lens on the market, being careful not to give any
damage on the mirror and lens.
To close the lens door properly, please take the
4.
following procedure.
(1) Insert the power cord with the lens door opened.
(2) The power indicator will light in orange, and the
lens door closes automatically. Do not touch the
Blower
lens door when the door is closing. Do not allow
anything to obstruct the lens door.
Cleaning cloth
NOTE
• When the lens door is closed manually, it may not shut properly.
•㩷The lens door may not close when the LENS DOOR LOCK function of the
SERVICE item in the OPTION menu is set to ON. For more information, please
see the “Operating Guide” on the CD.
WARNING
►Before caring for the projection mirror and lens, turn the
projector off and unplug the power cord, then cool the projector sufficiently.
►Do not use a vacuum cleaner to clean the projection mirror or lens, since it
might give some damage.
►Do not use cleaners or chemicals other than those specified in this manual.
Pay special attention to the mirror and lens as these materials could cause
serious damage to either.
►Be careful not to pinch your finger with the lens door, to prevent
CAUTION
an injury.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the CD manual
The other manuals for this product are written into the included CD-ROM titled
“User’s Manual (detailed)”. Before using the CD-ROM, please read the following
to ensure the proper use.
System requirements
The system for using the CD-ROM requires the following.
Windows®:
OS:Microsoft®
Windows® XP, Windows Vista®, Windows®7 or later
Macintosh®:
OS:Mac OS® 10.2 or later
CD-ROM/DVD-ROM drive:
Applications:
Microsoft® Internet Explorer®6.0 or later
Adobe® Acrobat® Reader® 8.0 or later
How to use the CD
1. Insert CD into computer’s CD-ROM/DVD-ROM drive.
Windows®:
In a while, Web browser automatically starts. Start up
window comes up.
Macintosh®:
(1) Double-click on the “PROJECTORS” icon appeared on
the desktop screen.
(2) When “main.html” file is clicked, Web browser will start
and Initial window will appear.
2. Click the model name of your projector first, and then click language you want
from the displayed list. The User’s manual (detailed) will open.
CAUTION ►Only use the CD-ROM in a computer CD/DVD drive. The
CD-ROM is designed for computer use only. NEVER INSERT THE CD-ROM
INTO A NON-COMPUTER CD/DVD PLAYER! Inserting the CD-ROM into an
incompatible CD/DVD drive may produce a loud noise, which in turn MAY
RESULT IN EAR AND SPEAKER DAMAGE!
• After using CD-ROM, please put it into CD case and keep it. Please keep
the CD neither in direct sunlight nor in a high temperature and high humidity
environment.
NOTE • The information in the CD-ROM is subject to change without notice.
• No responsibility is taken for any obstacle and defect to hardware and
software of your computer as a result of the use of the CD-ROM.
• All or Any part of the information in the CD-ROM must not be copied,
reproduced or republished without notice to our company.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Item
Specification
Product name
Liquid Crystal Panel
Lamp
Liquid crystal projector
8105B, 8106B: 786,432 pixels (1024 horizontal x 768 vertical)
8104WB: 1,024,000 pixels (1280 horizontal x 800 vertical)
456-8105B
10W: 8105B
16W: 8106B/8104WB
Speaker
AC 100-120V/3.3A, AC 220-240V/1.6A : 8105B
AC 100-120V/3.4A, AC 220-240V/1.7A : 8106B/8104WB
Power supply
AC 100-120V:320 W, AC 220-240V:300W : 8105B
Power consumption
Temperature range
AC 100-120V:330 W, AC 220-240V:310W : 8106B/8104WB
0 ~ 40°C (Operating)
35 ~ 40°C (The brightness of lamp is reduced automatically.)
345 (W) x 85 (H) x 303 (D) mm
Size
* Not including protruding parts.
Refer to figure F-6 at the back of this manual.
Weight (mass)
approx. 3.8 kg
Computer input port
HDMI input port
COMPUTER IN1
HDMI ............... HDMI connector ×1
....................... D-sub 15 pin mini x1 Audio input/output port
COMPUTER IN2
AUDIO IN1 ................ Stereo mini x1
....................... D-sub 15 pin mini x1 AUDIO IN2 ................ Stereo mini x1
Computer output port
AUDIO IN3 (R, L) ................. RCA x2
AUDIO OUT (R, L) ............... RCA x2
Ports
MONITOR OUT
....................... D-sub 15 pin mini x1 Others
Video input port
USB TYPE A ......................USB-Ax2
S-VIDEO ..............mini DIN 4 pin x1 USB TYPE B .....................USB-Bx1
VIDEO.................................RCA x1 CONTROL................. D-sub 9 pin x1
LAN ..................................... RJ45 x1
MIC..............................Mono mini x1
Lamp: 456-8105B
Filter set: UX37191
Optional parts
Tabletop use kit: TT-251
Laser remote control: RC-R008
USB wirelessless adapter: USB-WL-11N
* For more information, please consult your dealer.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting - Warranty and after-service
If an abnormal operation (such as smoke, strange odor or excessive sound)
should occur, stop using the projector immediately.
Otherwise if a problem occurs with the projector, first refer to “Troubleshooting” of
“Operating Guide” and “Network Guide”, and run through the suggested checks.
If this does not resolve the problem, please consult your dealer or service
company. They will tell you what warranty condition is applied.
Please check the following web address where you may find the latest information
for this projector.
DUKANE CORP AV SERVICE DEPT
2900 Dukane Drive
St Charles, IL 60174
800-676-2487 / 630-762-4032
Fax 630-584-5156
NOTE • The information in this manual is subject to change without notice.
• The illustrations in this manual are for illustrative purposes. They may differ
slightly from your projector.
• The manufacturer assumes no responsibility for any errors that may appear in
this manual.
• The reproduction, transfer or copy of all or any part of this document is not
permitted without express written consent.
Trademark acknowledgment
• Mac®, Macintosh® and Mac OS® are registered trademarks of Apple Inc.
• Adobe® and Acrobat®, Reader® are registered trademarks of Adobe Systems
Incorporated.
• Microsoft®, Internet explorer®, Windows®, Windows NT® and Windows Vista® are
registered trademarks of Microsoft Corporation in the U.S. and/or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
• Blu-ray DiscTM and Blu-rayTM are trademarks of Blu-ray Disc Association.
All other trademarks are the properties of their respective owners.
End User License Agreement for the Projector Software
• Software in the projector consists of the plural number of independent
software modules and there exist our copyright or/and third party copyrights for
each of such software modules.
• Be sure to read “End User License Agreement for the Projector Software”
which is separated document. (in the CD)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
430-8104WB-8105B-8106B-Concise-00
F-1
F-2
• On a horizontal surface
• Mounted on the wall or ceiling
b1
b2
a
c2
c1
a
c1
b1
c2
b2
8105B, 8106B
Screen size
(1024 x 768) ( 8%)
Screen height
T-1
Projection distance
b1 b2
(diagonal)
a
c1
c2
m
m
inch
m
inch
m
inch
m
inch
type(inch)
60
70
80
90
100
1.5
1.8
2.0
2.3
2.5
0.096
0.161
0.225
0.289
0.353
3.8
6.3
8.9
11.4
13.9
0.403
0.467
0.531
0.596
0.660
15.9
18.4
20.9
23.4
26.0
0.281
0.317
0.352
0.387
0.423
11.1
12.5
13.9
15.2
16.6
1.196
1.384
1.571
1.759
1.947
47.1
54.5
61.9
69.2
76.6
T-2
8104WB
Screen size
(1280 x 800) ( 8%)
Projection distance
b1 b2
Screen height
c1 c2
(diagonal)
a
m
m
inch
m
inch
m
inch
m
inch
type(inch)
60
70
80
90
100
1.5
1.8
2.0
2.3
2.5
0.120
0.188
0.256
0.324
0.392
4.7
7.4
10.1
12.8
15.4
0.426
0.494
0.562
0.631
0.699
16.8
19.5
22.1
24.8
27.5
0.295
0.332
0.369
0.407
0.444
11.6
13.1
14.5
16.0
17.5
1.102
1.274
1.446
1.618
1.791
43.4
50.2
56.9
63.7
70.5
Note: Dukane models described in this document are manufactured by Hitachi and use
the same firmware and software programs. The equivalent Dukane to Hitachi models are
8104WB (CP-AW252WN), 8105B (CP-A222WN), 8106B (CP-A302WN).
1
Download from Www.Somanuals.com. All Manuals Search And Download.
F-3
Computer
VCR/DVD/Blu-ray
Disc player
F-4
Speakers
Microphone
system
(with an amplifier)
Monitor
RGB IN
R
L
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Computer
F-5
Access point
RS-232C
LAN
USB TYPE A
USB
wireless
adapter
(optional)
USB storage
device
F-6
345
119
192
130
[unit: mm]
3
Download from Www.Somanuals.com. All Manuals Search And Download.
|