Dukane Projector 28A8910 User Manual

Liquid Crystal Projector

28A8910

USER'S MANUAL

Please read this user's manual thoroughly to ensure correct usage through understanding.

Download from Www.Somanuals.com. All Manuals Search And Download.

Liquid Crystal Projector

USER'S MANUAL

Thank you for purchasing this liquid crystal projector.

WARNING • Please read the accompanying manual “SAFETY

INSTRUCTIONS” and this “USER'S MANUAL” thoroughly to ensure correct

usage through understanding. After reading, store this instruction manual in a

safe place for future reference.

NOTE • The information in this manual is subject to change without notice.

• The manufacturer assumes no responsibility for any errors that may appear in this manual

• The reproduction, transmission or use of this document or contents is not permitted without

express written authority.

TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of

International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of

Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard

Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the

trademarks and registered trademarks of all companies, even when not mentioned.

CONTENTS

Page

FEATURES .......................................2

TROUBLESHOOTING ....................20

OSD Message ......................................20

Indicators Message ..............................21

Symptom ..............................................22

SPECIFICATIONS...........................23

WARRANTY AND AFTER-SERVICE......24

BEFORE USE ...................................2

Contents of Package ..............................2

Part Names.............................................3

Loading the Batteries..............................5

INSTALLATION ................................6

Installation of the Projector and Screen........6

Angle Adjustment ...................................6

Cabling ...................................................7

Power Connection ..................................8

Example of System Setup ......................8

Plug & Play.............................................8

OPERATIONS...................................9

Power ON ..................................................9

Power OFF ..............................................9

Basic Operation....................................10

Setup Menu ..........................................12

Input Menu............................................13

Image Menu..........................................14

Options Menu .......................................15

No Signal Menu....................................16

MAINTENANCE ..............................17

Lamp.....................................................17

Air Filter ................................................19

Other Maintenance...............................19

.......................................................................................

TABLES

Table 1. Installation Reference.................6

Table 2. Cabling .......................................7

Table 3. Basic Operations ......................10

Table 4. Setup Menu ..............................12

Table 5. Input Menu................................13

Table 6. Image Menu..............................14

Table 7. Options Menu ...........................15

Table 8. No Signal Menu........................16

Table 9. OSD Message ..........................20

Table 10. Indicator Message ..................21

Table 11. Symptom ................................22

Table 12. Specifications .........................23

.......................................................................................

For "TECHNICAL" and "REGULATORY

NOTICE", see the end of this manual.

ENGLISH-1

Download from Www.Somanuals.com. All Manuals Search And Download.

FEATURES

This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /

SECAM video signals onto a screen. Little space is required for installation and large images can

easily be realized.

Outstanding Brightness

The UHB lamp and high-efficiency optical system assure a high level of brightness.

Partial Magnification Function

Interesting parts of images can be magnified for closer viewing.

Distortion Correction Function

Distortion-free images are quickly available.

Extra-low Noise Function

Acoustic noise level from the unit can be reduced.

BEFORE USE

Contents of Package

Make sure all of the following items are included in the package. If anything is missing, please

contact your dealer.

NOTE • Keep the original packing material for future reshipment.

Power Cord

(UK Type)

Power Cord

(Europe Type)

Power Cord

(US Type)

Projector

Liquid Crystal Projector

CP-X430W

USER'S MANUAL

Please read this user's manual thoroughly to ensure correct usage through understanding.

BEDIENUNGSANLEITUNG

Bitte lessen Sie diese Bedienungsanleitung zugunsten der korrekten Bedienung

aufmerksam.

MANUEL D'UTILISATION

Nous vous recommandons de lire attentivement ce manuel pour bien assimiler le

fonctionnement de l'appareil.

MANUALE D'ISTRUZIONI

Vi preghiamo voler leggere attentamente il manuale d'sitruzioni in modo tale da poter

comprendere quanto riportato ai fini di un corretto utilizzo del proiettore.

MANUAL DE USUARIO

Lea cuidadosamente este manual del usuario para poder utilizar corretamente el

producto.

GEBRUIKSAANWIJIZNG

Lees voor het qebruik alstublieft deze handleiding aandachtig door, om volledig profijt te

hebben van de uitgebreide mogelijkheden.

Mouse cable

(PS/2)

BRUKERHÅNDBOK

Component

Video Cable

RGB Cable

Vennligst les denne bruksanvisningen grundig for

være garantert driftssikker bruk.

INSTRUÇÕES DO PROPRIETÁRIO

uso correto do equipamento, por favor leia atentamente este manual do

Para assegurar

usuário.

TECHNICAL

REGULATORY NOTICES

(with green lead)

User’s Manual

(this manual)

STANDBY/ON

VIDEO

BLANK

RGB

LASER

Safety Instructions

AUTO

KEYSTONE

MENU SELECT

POSITION

RESET

FREEZE

OFF

PinP

Batteries

for Remote Control

Transmitter

MAGNIFY

MUTE

Lens Cap

VOLUME

Remote Control

Transmitter

Carrying Bag

ENGLISH-2

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE USE (continued)

Part Names

Speaker

Zoom Knob

Focus Ring

Carrying Handle

Remote Control Sensor

Lens

Foot Adjuster

AC Inlet

(to the Power Cord)

Lens Cap

Power Switch

Foot Adjuster

Ventilation Openings

FRONT/LEFT VIEW OF

THE PROJECTOR

(Intake)

Control Panel (Refer to P.9 "OPERATIONS")

INPUT Button

STANDBY/ON Button

KEYSTONE Button

LAMP Indicator

TEMP Indicator

POWER Indicator

RESET Button

MENU Button

Foot Adjuster Button

Filter Cover

Air Filter and Intake

for the Cooling Fan

(

)

Ventilation Openings

(exhaust)

REAR/RIGHT VIEW OF

THE PROJECTOR

Terminal Panel

(Refer below)

S-VIDEO Terminal

Remote Control Sensor

DVI Terminal

COMPONENT VIDEO

Y Terminal

CB/PB Terminal

CR/PR Terminal

RGB IN 1 Terminal

RGB IN 2 Terminal

COMPONENT VIDEO

DVI

R/PR

B/PB

RGB IN

S-VIDEO IN

VIDEO IN

AUDIO

VIDEO IN Terminal

AUDIO IN R Terminal

AUDIO IN L Terminal

AUDIO IN 1 Terminal

AUDIO IN 2 Terminal

AUDIO OUT Terminal

AUDIO

AUDIO OUT

USB

RGB OUT

CONTROL

CONTROL Terminal

RGB OUT Terminal

USB Terminal

TERMINAL PANEL

ENGLISH-3

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE USE (continued)

Part Names (continued)

BLANK Button

STANDBY/ON Button

VIDEO Button

Disk Pad

LASER Button

RGB Button

MOUSE / RIGHT Button

Used to operate the

mouse shift function and

left click function.

Used to click the right

mouse button.

KEYSTONE Button

RESET Button

AUTO Button

MENU Button

Used to click the right

mouse button.

MENU SELECT Button

Used to click the left

mouse button.

PinP Button

FREEZE Button

MUTE Button

VOLUME Button

Button

Used to operate the

mouse shift function.

POSITION Button

MAGNIFY Button

REMOTE CONTROL

TRANSMITTER

(Refer to P.9 "OPERATIONS")

These functions works when the mouse control function is activated. Remember, the POSITION,

BLANK ON and MENU ON functions disable the mouse control function.

WARNING • The laser pointer of the remote control transmitter is used in

place of a finger or rod. Never look directly into the laser beam outlet or point

the laser beam at other people. The laser beam can cause vision problems.

CAUTION • Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous radiation exposure.

AVOID EXPOSURE-

LASER RADIATION-

LASER RADIATIONS IS

EMITTED FROM THIS

APERTURE

DO NOT STARE INTO BEAM

MAX. OUTPUT: 1mW

WAVE LENGTH 650nm

CLASS2 LASER PRODUCT

LASER RADIATION

DO NOT STARE INTO BEAM

CLASS2 LASER PRODUCT

MAX. OUTPUT: 1mW

WAVE LENGTH: 650nm

IEC60825-1:1993+A1:1997

Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations

pursuant to Laser Notice No.50, dated 2001.7.26

SMK CORPORATION

6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511

MANUFACTURED Novemver 2001

PLACE OF MANUFACTURER:

NOTE • Keep the remote control transmitter away from children and pets.

• Do not give the remote control transmitter any physical impact. Take care not to drop.

• Do not place the heavy objects on the remote control transmitter.

• Do not wet the remote control transmitter or place it on any wet object.

• Do not place the remote control transmitter close to the cooling fan of the projector.

• Do not disassemble the remote control transmitter.

ENGLISH-4

Download from Www.Somanuals.com. All Manuals Search And Download.

BEFORE USE (continued)

Loading the Batteries

Install the AA batteries into the remote control

transmitter.

1. Remove the battery cover.

Push the knob while lifting up the battery cover.

2. Load the batteries.

Make sure the plus and minus poles are correctly

oriented.

3. Close the battery cover.

CAUTION • Use only the specified batteries with this remote control

transmitter. Also, do not mix new and old batteries. This could cause in

battery cracking or leakage, which could result in fire or personal injury.

• When loading the batteries, make sure the plus and minus terminals are

correctly oriented as indicated in the remote control transmitter. Incorrect

orientation could cause battery cracking or leakage, which could result in

personal injury or pollution of the surrounding environment.

• When you dispose the battery, you should obey the law in the relative area or

country.

• Keep the battery away from children and pets.

• When not to be used for an extended period, remove the batteries from the

remote control transmitter.

NOTE Replace the batteries when remote control transmitter operation becomes difficult.

ENGLISH-5

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Installation of the Projector and Screen

Refer to the drawing and table below for determining of the screen size and projection distance.

The projection distances shown in the table below are for

full size (1024 x 768 dots).

a: Distance from the projector to the screen. ( 10%)

Table 1. Installation Reference

a [inches (m)]

Screen size

[inches (m)]

Min.

Max.

Top View

40 (1.0)

60 (1.5)

62 (1.6)

94 (2.4)

82 (2.1)

123 (3.1)

164 (4.2)

205 (5.2)

246 (6.3)

308 (7.8)

411 (10.4)

80 (2.0)

127 (3.2)

160 (4.1)

192 (4.9)

241 (6.1)

323 (8.2)

100 (2.5)

120 (3.0)

150 (3.8)

200 (5.0)

Side View

CAUTION • Install the projector in a suitable environment according to instructions of

the accompanying manual “SAFETY INSTRUCTIONS” and this manual.

• When you fix this unit with a metal tool and the like, you must connect it with ground

wire; otherwise, fire or electric shock can result.

Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the

building using an optional three-core power-supply cord.

• Please basically use liquid crystal projector at the horizontal position. If you use liquid

crystal projector by the lens up position, the lens down position and the side up position, this

may cause the heat inside to build up and become the cause of damage. Be especially careful

not to install it with ventilation holes blocked.

• Do not install LCD projector in smoke effected environment. Smoke residue may buildup

on critical parts (i.e.LCD panel, Lens Assy etc.).

Angle Adjustment

Use the foot adjusters on the bottom of the projector to adjust the projection angle. It is variable

within 0˚ to 9˚ approximately.

Press the foot

Foot Adjusters

adjuster button

1. Lift up the front side of the projector, and pressing the foot adjuster button, adjust the projection

angle.

2. Release the button to lock at the desired angle.

3. Make the foot adjusters screw for fine adjustment. Do not force the adjusters to make screw. This

could damage the adjusters or cause the lock to fail.

CAUTION • Do not release the foot adjuster button unless the projector is being held;

otherwise, the projector could overturn or the fingers could get caught and cause

personal injury.

ENGLISH-6

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

Cabling

Refer to the table below for connecting each terminal of the projector to each device.

Table 2. Cabling

Function

Terminal

Cable

RGB IN 1

RGB IN 2

RGB OUT

DVI

Accessory RGB cable or optional RGB

cable with D-sub 15-pin shrink jack and

inch thread screws

RGB input

RGB output

DVI input

Optional DVI cable with inch thread screws

AUDIO IN 1

(interlocked with RGB IN 1 or DVI)

Audio input

(from the computer)

Optional audio cable with stereo mini jack

AUDIO IN 2

(interlocked with RGB IN 2)

PS/2 mouse control

ADB mouse control

Serial mouse control

RS-232C communication

USB mouse control

Accessory PS/2 mouse cable

Optional ADB mouse cable

Optional Serial mouse cable

Optional RS-232C cable

Optional USB cable

CONTROL

USB

Optional S-video cable with mini DIN 4-pin

jack

S-video input

Video input

S-VIDEO IN

VIDEO IN

Optional video/audio cable

COMPONENT VIDEO Y

COMPONENT VIDEO CB/PB

COMPONENT VIDEO CR/PR

AUDIO IN L

Component video input

Accessory component video cable

Audio input

(from video equipment)

Optional video/audio cable or optional

audio cable with RCA jack

AUDIO IN R

Audio output

AUDIO OUT

Optional audio cable with stereo mini jack

CAUTION • Incorrect connecting could result in fire or electrical shock.

Please read this manual and the separate “SAFETY INSTRUCTIONS”.

• Before connecting, turn off to all devices to be connected, except for the USB

cable.

• The cables may have to be used with the core set to the projector side. Use the

cables which are included with the projector or specified.

NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the

projector is compatible with the device.

• Secure the screws on the connectors and tighten.

• For some RGB input modes, the optional Mac adapter is necessary.

• To select the DVI input, the comuter may need some settings. See the manuals of the computer for details.

• Some computers may have multiple display screen modes. Use of some of these modes will not be possible

with this projector.

• Refer to the “TECHNICAL” section for the pin assignment of connectors and RS-232C communication data.

• When the DVI terminal is used, the RGB OUT terminal may not function.

ENGLISH-7

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (continued)

Power Connection

Use the correct one of the enclosed power cords depending on the power outlet to be used.

Connect the AC inlet of the projector to the power outlet firmly by the power cord.

CAUTION • Be carful in handling the power

cord according to instructions of the

accompanying manual "SAFETY INSTRUCTIONS"

and this manual.

Power

outlet

• Connect the power cord firmly. Avoid using a

loose, unsound outlet or contact failure.

Power Cord

AC Inlet

Example of system setup

Display

Monitor

COMPONENT VIDEO

CR/PR CB/PB

DVI

DVD Player

RGB IN

S-VIDEO IN

VIDEO IN

AUDIO

AUDIO 1

AUDIO OUT

USB

RGB OUT

CONTROL

S-Video Tape

Recorder

Computer

(notebook type)

Speaker with

amplifier

Computer

(desktop type)

NOTE • When connecting with notebook computer, set to valid the RGB external image output

(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of

the notebook for more information.

Plug & Play

This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer

that is VESA DDC (Display Data Channel) compatible.

Please use this function by connecting the accessory RGB cable with RGB IN 1 terminal (DDC

1/2B compatible), or by connecting an optional DVI cable with DVI terminal (DDC 2B

compatible). Plug & play may not operate by other connecting.

NOTE • Plug & play is a system configured with peripheral equipment including a computer and

display, and an operating system.

• This projector is recognized as a plug & play monitor. Use the standard display drivers.

• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug &

play does not operate correctly.

ENGLISH-8

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS

BLANK

RGB

STANDBY/ON

VIDEO

STANDBY/

ON Button

LASER

STANDBY/ON Button

POWER Indicator

Zoom Knob

Focus Ring

AUTO

KEYSTONE

MENU SELECT

RESET

POSITION

FREEZE

OFF

PinP

MAGNIFY

MUTE

Lens Cap

Power Switch

VOLUME

Power ON

1. Check that the power cord is connected correctly.

2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to

orange.

3. Press the STANDBY/ON button

on the control panel or the remote control transmitter.

Warm-up begins and the POWER indicator blinks in green.

4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens

cap.

5. Adjust picture size using the zoom knob.

6. Adjust focus using the focus ring .

Power OFF

1. Press the STANDBY/ON button

on the control panel or the remote controller. Then,the

message "Power off?" will appear on the screen, and the message will disappear by any operation

or no operation for 5 seconds. During this message indication, press the STANDBY/ON

button again. The projector lamp is extinguished and lamp cooling begins. The POWER indicator

blinks orange during lamp cooling. Pressing the STANDBY/ON button

the POWER indicator is blinking.

has no effect while

2. The system assumes the Standby mode when cooling is complete, and the POWER indicator

ceases blinking and changes to orange. Check that the indicator is orange and set the power

switch to [O].

3. The POWER indicator is extinguished when power is off. Do not forget to attach the lens cap.

WARNING • Please read this manual, and the separate “SAFETY

INSTRUCTIONS” thoroughly before using the equipment. Always ensure that

the equipment is used safely.

NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off.

Incorrect procedure will reduce the life of the projector lamp and LCD panel.

• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF.

Providing a RS-232C cable is connected, turn on the computer before the projector.

• When a projector continues projecting the same image, the image may remain as an afterimage.

Please do not project the image same for a long time.

ENGLISH-9

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS (continued)

Basic Operation

The basic operations shown in Table 3 is performed from the supplied remote control transmitter or

the projector control panel. Items indicated by (*) may be used from the control panel.

Table 3 . Basic Operation

Item

Description

Select Input Signal (*) : Press the INPUT button.

RGB IN 1→RGB IN 2→DVI→ VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ RGB IN 1)

Select RGB Input : Press the RGB button.

VIDEO IN / S-VIDEO IN / COMPONENT VIDEO → RGB IN 1 / RGB IN 2 / DVI

RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)

Select Video Input : Press the VIDEO button.

INPUT

SELECT

RGB IN 1 / RGB IN 2 / DVI → VIDEO IN / S-VIDEO IN / COMPONENT VIDEO

VIDEO IN → S-VIDEO IN → COMPONENT VIDEO (→ VIDEO IN)

• The selected signal name is displayed for approximately 3 seconds when the input

signal is changed.

Set/Clear Position Adjustment Mode : Press the POSITION button.

The [ ] icon is displayed in the POSITION mode.

Image Position Adjustment: Press the

and

buttons in the

POSITION mode.

• Valid only in the MAGNIFY mode with a video signal is input.

POSITION

• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the

POSITION mode is cleared automatically.

•

and

buttons may operate as the mouse control button. Refer to page 4.

Initialise Each Item : Select an item and press the RESET button.

Initialise Position Adjustment : Press the RESET button and the

POSITION mode. This function is valid only when RGB signal is input.

• Valid except for the VOLUME, LANGUAGE and H PHASE.

RESET (*)

• The RESET button may operate as the mouse control button. Refer to page 4.

Set MAGNIFY Mode : Press the MAGNIFY

button.

Move Magnified Area : Run the POSITION in the MAGNIFY mode.

Adjust Magnification : Press the MAGNIFY

mode.

Clear MAGNIFY Mode : Press the MAGNIFY

• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT

button in MAGNIFY

MAGNIFY

OFF

button.

SELECT or VIDEO, or by changing the input signal.

Set/Clear FREEZE Mode : Press the FREEZE button. The [

II] icon is

displayed, and the image frozen, in the FREEZE mode.

• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,

Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the

input signal.

FREEZE

• Do not forget to clear frozen static images.

NOTE • Strong light and obstacles will interfere with operation of the remote control transmitter.

ENGLISH-10

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS (continued)

Items indicated by (*) may be used from the control panel.

Table 3. Basic Operation (continued)

Item

Description

VOLUME

Volume Adjustment : Press the VOLUME

button.

Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the

MUTE mode.

MUTE

AUTO

Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal

position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE),

and horizontal size(H.SIZE) are automatically adjusted. Use with the

window at maximum size in the application display.

Automatic Adjustment at Video Input : Press the AUTO button. A signal

type appropriate for the input signal is selected automatically. Valid only

when AUTO is set for VIDEO on the menu.

• This operation requires approximately 10 seconds. It may not function correctly

with some input signals.

BLANK

Set/Clear Blank Mode: Press the BLANK button. No image is displayed in

ON/OFF

the Blank mode. The screen color is as set in BLANK on the Image menu.

Menu Display Start/Stop: Press the MENU button.

• The menu display is terminated automatically after approximately 10 seconds of

inactivity.

ON/OFF (*)

Select Menu Type: Press the MENU SELECT button. Allows the user to

select the normal menu or the single menu. Only the selected item is

displayed on the single menu, and other items are displayed with the

and

buttons as with the normal menu.

• Valid only when the Setup menu is used. Push the MENU SELECT button after

selecting items such as "BRIGHTNESS".

• The MENU SELECT button may operate as the mouse control button. Refer to

page 4.

SELECT

Normal menu

Single menu

(MENU SELECT)

SETUP

INPUT

IMAGE

OPT.

BRIGHT

CONTRAST

-2

POSIT

PHASE

100

SIZE

800

COLOR BAL

ASPECT

CONTRAST

-2

Select Mode of P.IN P. Display : Press the PinP button.

Small → Large → P.IN P. off ( → Small)

• Valid only at RGB IN 1, RGB IN 2 or DVI input.

P.IN P.

MODE

Set / Clear KEYSTONE Mode (*) : Press the KEYSTONE

button.

Select KEYSTONE Mode : Press the

button in the KEYSTONE

KEYSTONE

mode. Vertical

↔

Horizontal

Adjust KEYSTONE : Press the

button.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-11

OPERATIONS (continued)

SETUP

BRIGHT

CONTRAST

SHARPNESS

COLOR

TINT

H PHASE

COLOR BAL

ASPECT

INPUT

IMAGE

OPT.

SETUP

INPUT

IMAGE

OPT.

Setup Menu

-2

BRIGHT

CONTRAST

V POSIT

H POSIT

H PHASE

The following adjustments and settings are possible

when SETUP is selected at the top of the menu. Part

of the Setup menu differs between RGB input and

100

H SIZE

800

COLOR BAL R

COLOR BAL B

ASPECT

video input. Select an item with the

and

buttons, and start operation. Use the Single menu to

reduce menu size (see Table 3, MENU SELECT).

RGB IN 1

RGB IN 2

DVI

VIDEO

S-VIDEO

COMPONENT VIDEO

Table 4. Setup Menu

VIDEO

S-VIDEO

COMPONENT

RGB IN 1

RGB IN 2

DVI

Item

Description

✔

BRIGHT

Adjustment: Dark

Adjustment: Weak

Adjustment: Down

Adjustment: Left

↔ Light

↔ Strong

↔ Up

CONTRAST

V POSIT

H POSIT

↔ Right

✔

H PHASE

H SIZE

• Adjust to eliminate flicker.

Adjustment: Small ↔ Large

• The image may not be displayed correctly if the horizontal

size is excessive. In such cases, press the RESET button,

and initialize the horizontal size.

✔

SHARPNESS

COLOR

Adjustment: Soft

Adjustment: Light

Adjustment: Red

↔ Clear

↔ Dark

↔ Green

✔

TINT

• Valid only when NTSC or NTSC 4.43 signal is received.

✔

COLOR BAL R

COLOR BAL B

Adjustment: Light

↔ Dark

Select Image Aspect Ratio :

Full [ 16:9[

Select Position of Image:

]

↔

]

✔

Press the

button while 16:9[

] is selected.

Center →

Down →

Up ( → Center )

Select Image Aspect Ratio:

4:3[ 16:9[

Select Position of Image :

]

↔

]

↔

4:3 small[

]

ASPECT

Press the

is selected.

Center →

button while 16:9[

] / 4:3 small[

✔

Down →

Up ( → Center

)

• 4:3 small cannot be selected with the input of 720p or

1080i component.

• 4:3 small may not be displayed correctly with some input

signals.

ENGLISH-12

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS (continued)

Input Menu

menu. Select an item with the

operation with the and

SETUP

AUTO

RGB

VIDEO

HDTV

INPUT

IMAGE

OPT.

The following functions are available when INPUT is selected on the

EXECUTE

CANCEL

and

buttons, and start or stop

buttons. The function indicated (**) are

effective on video input mode only, not on RGB input mode, except in

the P.IN P. window on RGB input mode.

Table 5. Input Menu

Item

Description

Automatic Adjustment at RGB Input: Select the EXECUTE with the

button. Horizontal position (H.POSIT), vertical position (V.POSIT), clock

phase (H.PHASE), and horizontal size (H.SIZE) are automatically adjusted.

Use with the window at maximum size in the application display.

Automatic Adjustment at Video Input: Select the EXECUTE with the

button. A signal type appropriate for the input signal is selected

automatically when EXECUTE is selected automatically. Valid only when

AUTO is set for VIDEO on the menu.

AUTO

•

This operation requires approximately 10 seconds. It may not function correctly with

some input signals. Pressing the AUTO button in this case may correct this problem.

• This function is the same as for the AUTO function in Basic operation.

Displays RGB Input Frequency: Displays the horizontal and vertical sync

signal frequencies for RGB input.

RGB

• Valid only at RGB input.

Select Video Signal Type: Select the signal type with the

and

buttons. Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as

appropriate for the input signal. The selection of AUTO enables and

executes the function AUTO (Automatic Adjustment at Video Input), except

for the N-PAL input.

• Use this function when the image becomes unstable (eg. the image becomes

irregular, or lacks color) at VIDEO/S-VIDEO input.

VIDEO (**)

• Automatic Adjustment requires approximately 10 seconds. It may not function

correctly with some input signals. Pressing the AUTO button in this case may correct

this problem except for the N-PAL input.

• For the COMPONENT VIDEO input, this function is not effective and the signal

type is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the

signal of HDTV.

Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the

HDTV

input signal with the

button.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-13

OPERATIONS (continued)

Image Menu

SETUP

BLANK

START UP

MyScreen

INPUT

IMAGE

OPT.

MyScreen

ORIGINAL

The following adjustments and settings are available when IMAGE is

selected on the menu. Select an item with the

start or stop operation with the

and

buttons, and

MIRROR

P. IN P. POSIT

P. IN P. INPUT

GAMMA

and

buttons.

Table 6. Image Menu

Item

Description

Select Blank Screen: Select the screen in case of the BLANK mode with the

button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the

BLANK mode is ON.

BLANK

MyScreen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.

Select Start Up Screen: Select the screen in case of no signal input with the

button. The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when

no signal is input.

My Screen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

TURN OFF displays the blue screen.

START UP

• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.

Set MyScreen Mode: Select the EXECUTE with the

button to display the

MyScreen menu and set the MyScreen mode for BLANK and START UP functions.

ESC clears and closes the menu box.

NORM. is default of the MyScreen menu.

FREEZE freezes the image and displays the frame to capture.

Press the

button after freeze to go to the MyScreen Capture Position mode.

In the MyScreen Capture Position mode, the buttons

move the frame to capture.

and

allow to

After adjusting the position, press the KEYSTONE button to go to the MyScreen

Display Size mode.

MyScreen

To cancel freezing and return to the NORM. of the MyScreen menu, press the

RESET button.

In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with

the button

. After selecting the magnification, press the KEYSTONE button to

go to the CAPT. mode and start capturing.

To return to the MyScreen Capture Position mode, press the RESET button.

CAPT. executes a capturing the image. It requires about 20 seconds. After capturing,

the captured image will be displayed for about 10 seconds.

MIRROR

Select Mirror Status: Select mirror status with

Select Position of P. in P. Display : Press the

button.

P. IN P.

POSIT

↔

• Valid only at RGB IN 1, RGB IN 2 or DVI input.

P. IN P.

INPUT

Select signal of P. in P. Display : Press the

button.

VIDEO

Select Gamma Mode: Select the gamma mode with the

NORMAL CINEMA DYNAMIC

↔

S-VIDEO

button.

GAMMA

↔

ENGLISH-14

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATIONS (continued)

Options Menu

SETUP

VOLUME

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

INPUT

IMAGE

OPT.

The following adjustments and settings are available when OPT. is

selected on the menu. Select an item with the

start or stop operation with the

and

buttons, and

and

buttons.

IR REMOTE

Table 7. Options Menu

Item

Description

VOLUME

Reduce

↔

Increase

MENU COLOR Select Menu Background Color: Select with the

button.

LANGUAGE

Select Menu Display Language: Select with the

Set AUTO OFF: Set 1~99 minutes with the

button. The system

automatically enters the standby mode when a signal is not received for

the set time.

AUTO OFF

Clear AUTO OFF: Select STOP (0 min.) with the

button. When

STOP is selected the system does not enter the standby mode even if

no signal is received.

SYNC ON G Valid: Select TURN ON with the

SYNC ON G Invalid: Select TURN OFF with the

• May not be displayed correctly with some input signals when SYNC ON G is

valid. In such cases, remove the signal connector so that no signal is received,

set SYNC ON G to invalid, and reconnect the signal.

button.

SYNC ON G

WHISPER

Set / Crear WHISPER Mode: Press the

button. When the

WHISPER is selected, the WHISPER mode is active. In the WHISPER

mode, acoustic noise level from the unit is reduced, and brightness level

on screen is a little lower.

Select Remote Control Sensor: Select the sensors to activate along

the menu with the

button. Use this function if the remote does

not work stably. The ambient light may affect the remote.

SETUP

VOLUME

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

INPUT

IMAGE

OPT.

IR REMOTE

: active

: inactive

IR REMOTE

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-15

OPERATIONS (continued)

No Signal Menu

VOLUME

BLANK

START UP

MIRROR

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

IR REMOTE

The same adjustments and settings are available as with the Image and

Options menus when the MENU button is pressed during display of the

“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE

ON ***” message while no signal is received.Select an item with the

and

buttons, and start or stop operation with the

and

buttons.

Table 8. No Signal Menu

Item

Description

Reduce

↔

Increase

• When this function is used, audio input is automatically switched to video. The audio input can

VOLUME

BLANK

be switched by moving the DISK PAD left and right during the display of the volume adjustment

bar. The volume adjustment bar is displayed by pressing VOLUME

button.

Select Blank Screen: Select the screen in case of the BLANK mode with the

button. The selected one (MyScreen, ORIGINAL or one colors) is displayed when the

BLANK mode is ON.

MyScreen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

•

When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.

Select Start Up Screen: Select the screen in case of no signal input with the button.

The selected one (MyScreen, ORIGINAL or TURN OFF) is displayed when no signal is input.

My Screen is a mode that the customer-customized screen is displayed. This is the

blue screen at the factory setting. Refer to the description of MyScreen below.

ORIGINAL is a mode that the factory fixed screen is displayed.

START UP

TURN OFF displays the blue screen.

• When MyScreen or ORIGINAL is selected, the screen is going to the black after several minutes.

MIRROR

Select Mirror Status: Select the mirror status with the

button.

MENU COLOR

LANGUAGE

Select Menu Background Color: Select the color with the

Select Menu Display Language: Select the language with the

Set AUTO OFF: Set 1~99 minutes with the

automatically enters the standby mode when a signal is not received for the set time.

Clear AUTO OFF: Select the STOP (0 min.) with the button. When the STOP is

selected the system does not enter the standby mode even if no signal is received.

button. The system

AUTO OFF

SYNC ON G Valid: Select the TURN ON with the

SYNC ON G Invalid: Select the TURN OFF with the

• May not be displayed correctly with some input signals when the SYNC ON G is valid. In such

cases, remove the signal connector so that no signal is received, set the SYNC ON G to invalid,

and reconnect the signal.

button.

SYNC ON G

WHISPER

Set / Crear WHISPER Mode: Press the

button. When the WHISPER is

selected, the WHISPER mode is active. In the WHISPER mode, acoustic moise level

from the unit is reduced, and brightness level on screen is a little lower.

Select Remote Control Sensor: Select the sensors to activate along the menu with

the

button. Use this function if the remote does not work stably. The ambient

light may affect the remote.

VOLUME

BLANK

START UP

MIRROR

MENU COLOR

LANGUAGE

AUTO OFF

SYNC ON G

WHISPER

IR REMOTE

: active

: inactive

IR REMOTE

ENGLISH-16

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

Lamp

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

Contact your dealer before replacing the lamp.

For the optional lamp, see the item “Optional Parts” of the Table 12.

Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and

wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high

temperatures.

WARNING • For disposal of used lamp, treat

according to the instruction of community

authorities.

• Since the lamp is made of glass, do not apply shock

to it and do not scratch it.

• Also, do not use old lamp. This could also cause

explosion of the lamp.

Lamp

• Premature lamp failure MAY be caused by an

electronic component in the projector and not

necessarily the lamp. If unsure contact your local

service center.

• If it is probable that the lamp has exploded (explosive

sound is heard), disconnect the power plug from the

power outlet and ask your dealer to replace lamp. The

lamp is covered by front glass, but in rare cases, the

reflector and the inside of the projector may be

damaged by scattered broken pieces of glass, and

broken pieces could cause injury when being handled.

• Do not use the projector with the lamp cover removed.

Reflector

Front

glass

Lamp Life

Projector lamps have a finite life. The image will become darker, and hues will become weaker,

after a lamp has been used for a long period of time.

Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears

when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.

NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before

replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.

If the LAMP indicator is still red, replace the lamp.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-17

MAINTENANCE (continued)

Replacing the Lamp

1. Switch the projector OFF, remove the power cord from the

power outlet, and wait at least 45 minutes for the unit to cool.

2. Prepare a new lamp.

3. Check that the projector has cooled sufficiently, and gently

turn it upside down.

4. Loosen the two screws as shown in the diagram, and remove

the lamp cover.

5. Loosen the three screws, and gently remove the lamp while

holding the grips. Touching the inside of the lamp case may

result in uneven coloring.

6. Install the new lamp and tighten the three screws firmly.

Also steadily push the opposite side of the screwed lamp into

the unit.

7. Replace the lamp cover in position and tighten the two

screws firmly.

8. Gently turn the projector right-side up.

CAUTION • Ensure that screws are tightened

properly. Screws not tightened fully may result

in injury or accidents.

• Do not use the projector with the lamp cover

removed.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP

indicator is red, or the CHANGE THE LAMP message is displayed, complete the following

operation within ten minutes of switching power ON. The power will be turned off automatically in

over 10 minutes.

1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP

xxxx hr’ message will appear on the lamp timer on the bottom of the screen.

2. Press the MENU button on the remote control transmitter, or the RESET button on the control

panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 ꢀ CANCEL’ message will

then appear.

3. Press the

and select 0, and wait until the timer display is cleared.

NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always

when replacing the lamp. The message functions will not operate properly if the lamp timer is not

reset correctly.

ENGLISH-18

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE (continued)

Air Filter

Cleaning the air Filter

The air filter should be cleaned as described below at intervals of approximately 100 hours.

1. Switch the projector power supply OFF, and remove the power cord from the power outlet.

2. Clean the air filter with a vacuum cleaner.

Replacing the Air Filter

Replace the air filter if contamination cannot be removed, or if it is damaged.

1. Remove the filter cover.

2. Remove the old filter.

3. Set the new filter and the filter cover.

CAUTION • Switch power OFF and remove the power cord from the power

outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

• Replace the air filter if contamination cannot be removed, or if it is damaged.

Contact your dealer in such case. For the optional air filter, see the item “Option

Parts” of the Table 12.

• Do not use the equipment with the air filter removed.

• When the air filter is clogged with dust etc. the power supply is switched OFF

automatically to prevent the temperature rising inside the projector.

Other Maintenance

Maintenance Inside the Equipment

For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two

years. Maintaining the equipment by yourself is dangerous.

Cleaning the Lens

Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.

Cleaning the Cabinet and Remote control transmitter

Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth

dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.

CAUTION • Switch power OFF and remove the power cord from the power

outlet before beginning maintenance work. Please read the separate “SAFETY

INSTRUCTIONS” thoroughly to ensure that maintenance is performed correctly.

• Do not use detergents or chemicals other than those noted above (e.g. benzene

or thinners).

• Do not use cleaning sprays.

• Do not rub with hard materials, or tap the equipment.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-19

TROUBLESHOOTING

OSD Message

The messages as described below may appear on the screen at power ON. Take the appropriate

measures when such messages appears.

Table 9. OSD Messages

Message

Contents

The usage time of lamp will be reaching 2000 hr

shortly.(*2)

It is recommended to replace the lamp soon. Prepare a

new lamp as a replacement.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

(*1)

The usage time of lamp will be reaching 2000 hr shortly.

It is recommended to replace the lamp within * *

hours.(*2)

It might be happened that the lamp is cut off before * * hr

by any chance. Power will be switched OFF

automatically in * * hours. Replace the lamp as shown in

P.17~18 “Lamp”. Always reset the lamp timer after

replacing the lamp.

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL TURN OFF

AFTER ** hr.

(*1)

CHANGE THE LAMP

AFTER REPLACING LAMP,

RESET THE LAMP TIME.

THE POWER WILL

TURN OFF

The usage time of lamp is about to reach. Power will be

switched OFF in a few minutes.(*2)

Switch power OFF immediately and replace the lamp as

shown in P.17 ~18 “Lamp”. Always reset the lamp timer

after replacing the lamp.

AFTER 0 hr.

NO INPUT IS DETECTED

No input signal found.

Check signal input connections and signal sources.

ON ***

The horizontal or vertical frequency of the input signal is

not within the specified range.

Check the specifications of the equipment and the signal

source.

SYNC IS OUT OF RANGE

ON ***

NOTE (*1) This message is cleared automatically after approximately three minutes, and

appears every time power is switched ON.

(*2) The unit has a function to turn the power off which will be active when the usage time reaches

2000 hr. However the life of lamp might be much different among lamps, so that it might be

happened that a lamp is cut off before the function is active.

ENGLISH-20

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING (continued)

Indicators Message

The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the

appropriate measures.

Table 10. Indicators Message

POWER LAMP TEMP

Contents

indicator indicator indicator

Lights

Turns off Turns off The Standby mode has been set.

orange

Blinks

Turns off Turns off Warming up. Please wait.

green

Lights

Turns off Turns off ON. Normal operation possible.

green

Blinks

orange

Turns off Turns off Cooling. Please wait.

Cooling. Please wait.

Blinks red

The error is found. Take the appropriate measures when the

POWER indicator ceases blinking

Lamp is not lit.

The interior of the equipment may be too hot. Switch power OFF,

wait 20 minutes until the equipment cools, and check whether the

ventilation openings are blocked, whether the air filter is dirty, or

whether the ambient temperature exceeds 35 °C. And switch

power ON again. Replace the lamp if the same problem occurs.

Blinks

/Lights red

Lights

red

Turns off

Lamp or lamp cover is not found, or hasn’t been fitted in correctly.

Switch power OFF, and wait for 45 minutes until the equipment

cools. Check fitting of the lamp and lamp cover, and switch power

ON again. Contact your dealer if the same problem occurs again.

Blinks

/Lights red

Blinks

red

Turns off

The cooling fan is not operating.

Blinks

/Lights red

Blinks Switch power OFF, and wait for 20 minutes until the equipment

Turns off

cools. Check for foreign matters in the fan, and switch power ON

again. Contact your dealer if the same problem occurs again.

red

The interior of the equipment is too hot.

Switch power OFF, and wait for 20 minutes until the equipment

cools. Check whether the ventilation openings are blocked,

whether the air filter is dirty, or whether the ambient temperature

exceeds 35 °C. Then switch power ON again. Contact your dealer if

the same problem occurs again.

Blinks

/Lights red

Turns off Lights red

The interior of the equipment is too cool.

Lights

green

Blinks

red

Blinks Check whether the ambient temperature is below 0°C. Contact your

dealer if the same problem occurs when the ambient temperature is

red

0~35°C.

NOTE When the internal temperature becomes excessive power is switched OFF automatically

for safety reasons, and the indicator is extinguished. Set the power switch to [

O] and wait for 20

minutes until the equipment has cooled sufficiently.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-21

TROUBLESHOOTING (continued)

Symptom

Before requesting repair, check in accordance with the following chart. If the situation cannot be

corrected, then contact your dealer.

Table 11. Symptom

Symptom

Possible cause

Remedy

Page

The main power switch is not

turned on.

Turn on the main power switch.

The power is not

turned on.

8,9

The power cord is

disconnected.

Plug the power cord into an AC

power outlet.

Use the projector or remote control

transmitter to set.

The input is not correctly set.

No signal input.

7,8

No video or audio.

Connect correctly.

The projector is not correctly

connected.

Press VOLUME

control or display the menu screen

and adjust the volume.

on the remote

Video is present but

no audio.

The volume is set to minimum.

11,15

Mute is turned on.

Press the MUTE

Connect correctly.

button.

7,8

The projector is not correctly

connected.

Audio is present but

no video.

Select BRIGHT with the MENU

button and the press the

The brightness adjustment knob

is rotated fully clockwise.

button.

The lens cap is still attached.

Remove the lens cap.

Colors are pale and Color density and color

color matching is

poor.

matching are not correctly

adjusted.

Adjust the video.

Brightness and contrast are not

correctly adjusted.

Adjust the video.

The lamp is nearing the end of

its service life.

Images are dark.

Video is blurred.

Replace with a new lamp.

Clear WHISPER mode.

Adjust the focus or H PHASE.

WHISPER mode is set.

Focus or H PHASE is out of

adjustment.

9,12

ENGLISH-22

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

Table 12. Specifications

Item

Specification

Product name

Liquid crystal projector

Panel size

2.3 cm (0.9 type)

TFT active matrix

Liquid

crystal

panel

Drive system

Pixels

786,432 pixels (1024 horizontal x 768 vertical)

Zoom lens F=1.7 ~ 2.1 f=36.8 ~ 47.8 mm

250 W UHB

Lens

Lamp

Speaker

1.0W+1.0W (stereo)

Power supply

Power consumption

Temperature range

Size

AC100 ~ 120V, 4.5A / AC220 ~ 240V, 1.9A

410W

0 ~ 35°C (Operating)

360 (W) x 106 (H) x 256.5 (D) mm

4.3 kg

Weight (mass)

Video: Analog 0.7Vp-p, 75Ω terminator (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB IN

RGB

D-sub 15-pin shrink jack

TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p

TTL Level (Positive/Negative)

signal

input

DVI

RGB1

DVI

200mVrms, 50 kΩ (max. 3.0Vp-p)

Stereo mini jack

AUDIO IN

RGB2

1.0Vp-p, 75Ω terminator

RCA jack

VIDEO IN

Brightness signal: 1.0Vp-p, 75Ω terminator

Color signal: 0.286Vp-p (NTSC, burst signal),75Ω terminator

0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator

Mini DIN 4-pin jack

S-VIDEO IN

Video

signal

input

1.0 Vp-p, 75 Ω Terminator (Positive)

CB/CR 0.7 Vp-p, 75 Ω Terminator (Positive)

PB/PR 0.7 Vp-p, 75 Ω Terminator (Positive)

COMPONENT

VIDEO

200mVrms, 50 kΩ (max. 3.0Vp-p)

RCA jack

AUDIO IN

Video: Analog 0.7Vp-p, 75Ω output impedance (positive)

H/V. sync.: TTL level (positive/negative)

Composite sync.: TTL level

RGB OUT

Signal

output

D-sub 15-pin shrink jack

200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)

Stereo mini jack

AUDIO OUT

CONTROL

USB

D-sub 15-pin shrink plug

USB jack (B type)

Control

functions

Lamp: DT00471

Air Filter: NJ06131

Optional Parts

* For others, consult your dealer.

NOTE • This specifications are subject to change without notice.

_{Download from Www.Somanuals.com. All Manuals Search And Download}E_.NGLISH-23

WARRANTY AND AFTER-SERVICE

If a problem occurs with the equipment, first refer to the P.20 “TROUBLESHOOTING” section and

run through the suggested checks. If this does not resolve the problem contact your dealer or service

company. They will tell you what warranty condition is applied.

ENGLISH-24

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL

Dimension Diagram

O C N T R O L

R G B O U T

I N

A U D I O

S B U

A U D I

2 O

O U T

I N

A U D I O

V I D E O I N L

S - V I D E O I N

R G B I N

/ P B

/ P R

D V I

C O M P O N E N T V I D E O

360

108.4

Unit : mm

Signal Connector Pin Assignment

1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)

Pin No

Signal

Video input Red

Video input Green

Video input Blue

Pin No

Signal

Pin No

Signal

RGB IN 1: SCL(DDC)

Ground

RGB IN 2:

RGB OUT:

RGB IN 1: SDA(DDC)

Ground

RGB IN 2:

RGB OUT:

Ground Red

Ground Green

Ground Blue

H. sync./ Composite sync.

Vertical sync

2. Digital Receptacle Connector (DVI)

Pin No

Signal

T.M.D.S. Data 2 -

T.M.D.S. Data 2 +

T.M.D.S. Data 2 / 4 Shield

Pin No

Signal

Pin No

Signal

T.M.D.S. Data 1 / 3 Shield

T.M.D.S. Clock Shield

T.M.D.S. Clock +

T.M.D.S. Clock -

+5V Power

Ground (+5V, Analog H/V Sync.)

Hot-Plug Sense

T.M.D.S. Data 0 -

T.M.D.S. Data 0 +

T.M.D.S. Data 0 / 5 Shield

DDC Clock

DDC Data

10 11 12 13 14 15 16

Analog V. Sync.

T.M.D.S. Data 1 -

T.M.D.S. Data 1 +

17 18 19 20 21 22 23 24

3. Mini Din 4-pin Connector (S-VIDEO)

Pin No

Signal

Color:0.286Vp-p (NTSC, burst signal),75Ω terminator

0.300Vp-p (PAL/SECAM, burst signal),75Ω terminator

Brightness:1.0Vp-p, 75Ω terminator

Ground

TECHNICAL - 1

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Example of computer signal

Resolution

fH (kHz)

fV (Hz)

Rating

Signal mode

Display mode

H × V

640 × 350

640 × 400

720 × 400

640 × 480

800 × 600

832 × 624

1024 × 768

1152 × 864

1280 × 960

1280 × 1024

37.9

31.5

35.0

37.9

37.5

43.3

35.2

37.9

48.1

46.9

53.7

49.7

48.4

56.5

60.0

68.7

67.5

60.0

64.0

85.1

85.0

59.9

66.7

72.8

75.0

85.0

56.3

60.3

72.2

75.0

85.1

74.5

60.0

70.1

75.0

85.0

75.0

60.0

VESA

VGA-1

Zoom in

VGA-2

TEXT

VGA (60Hz)

Mac13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

SXGA (75Hz)

SXGA (60Hz)

VESA

Zoom out

1280 × 1024

80.0

75.0

VESA

SXGA (75Hz)

NOTE • Some computers may have multiple display screen modes. Use of some of these modes

will not be possible with this projector.

• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a

computer.

• Depending on the input signal, full-size display may not be possible in some cases. Refer to the

number of display pixels above.

• The image may not be displayed correctly when the input sync. signal is "Composite Sync." or

"Sync. on G".

• The image might be something wrong with computer by computer on the DVI mode. In the case, it

is recommended to reduce the resolution and / or reflesh rate.

TECHNICAL_D-_o2_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Initial set signals

The following signals are used for the initial settings.

The signal timing of some computer models may be different. In such case, refer to adjust the

V.POSIT and H.POSIT of the menu.

Back porch b

Front porch d

Back porch b

Display interval c

Front porch d

Display interval c

Sync a

Computer /

Signal

Horizontal signal timing (µs)

Computer /

Signal

Vertical signal timimg (lines)

350

VGA-1 (85Hz)

VGA-2 (85Hz)

TEXT

2.0

3.0

20.3

1.0

VGA-1 (85Hz)

VGA-2 (85Hz)

TEXT

2.0

3.8

2.1

1.3

2.0

1.6

2.0

3.2

2.4

1.6

1.1

2.1

1.8

1.2

1.0

1.2

1.0

1.1

3.0

1.9

3.2

3.8

2.2

3.6

2.2

1.3

3.2

2.7

3.9

2.5

1.9

2.2

2.4

2.9

2.3

1.8

20.3

25.4

21.2

20.3

17.8

22.2

20.0

16.0

16.2

14.2

14.5

15.8

13.7

13.0

10.8

10.7

11.9

9.5

1.0

0.6

2.1

1.0

0.5

1.6

0.7

1.0

1.1

0.3

0.6

0.4

0.3

0.2

0.5

0.6

0.9

0.4

0.1

400

480

600

624

768

864

960

1024

VGA (60Hz)

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

VGA (60Hz)

Mac 13"mode

VGA (72Hz)

VGA (75Hz)

VGA (85Hz)

SVGA (56Hz)

SVGA (60Hz)

SVGA (72Hz)

SVGA (75Hz)

SVGA (85Hz)

Mac 16"mode

XGA (60Hz)

XGA (70Hz)

XGA (75Hz)

XGA (85Hz)

1152×864 (75Hz)

1280×960 (60Hz)

1280×1024 (60Hz)

1280×1024 (75Hz)

TECHNICAL - 3

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Connection to the Mouse Control

1. PS/2, ADB or Serial Mouse

(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For

PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult

your dealer.

(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.

(3) Turn on the computer.

(4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or

reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.

2. USB Mouse

(1) Connect the projector and computer with a suitable commercially available USB cable. Consult

your dealer to get the cable, if you need.

(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT

button” of page 4.

NOTE • Before connecting, read the instruction manuals of the devices to be connected.

• In the case of notebook type computers with an internal pointing device, the mouse control

function will not work unless the internal pointing device is disabled. In such case, disable the

internal pointing device and change the BIOS setting to select an external mouse before the

operations described in (1) to (4) above.

Also, some computers may not have a utility program to operate a mouse.

Refer to the computer hardware manual for detail.

PS/2 Mouse

Projector

Computer

DATA

CLK

DATA

Mouse jack

Mini DIN 6-pin

CONTROL Terminal

GND

+5V

CLK

D-sub 15-pin shrink jack

SEL0

RTS

+5V

GND

TECHNICAL_D-_o4_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

ADB Mouse

Projector

Computer

ADB

(

)

POWER ON

CONTROL Terminal

DATA

RTS

+5V

GND

Mouse jack

Mini DIN 4-pin

D-sub 15-pin shrink jack

+5V

GND

Serial Mouse

Projector

Computer

CONTROL Terminal

DTR

GND

DSR

RTS

CTS

Mouse jack

D-sub 9-pin

D-sub 15-pin shrink jack

SEL0

RTS

GND

USB Mouse

USB jack

(B type)

Projector

Computer

1 +_5V

USB jack

(A type)

—

DATA

DATA 3

GND

DATA

GND

USB cable

TECHNICAL - 5

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

RS-232C communication

(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.

(2) Turn on the computer power supply and, after the computer has started up, turn on the projector

power supply.

Projector

Computer

RS-232C jack

D-sub 9-pin

Control jack

D-sub 15-pin shrink jack

DTR

GND

DSR

RTS

CTS

SELO

RTS

GND

Communications setting

19200bps, 8N1

1 Protocol

Consist of header (7 bytes) + command data (6 bytes).

2 Header

BE + EF + 03 + 06 + 00 + CRC_low + CRC_high

CRC_low : Lower byte of CRC flag for command data.

CRC_high : Upper byte of CRC flag for command data.

3 Command data

Command data chart

byte_0

byte_1

high

byte_2

byte_3

byte_4

Setting code

low high

byte_5

Action

Type

low

high

Action (byte_0 - 1)

Action

Classification

Content

SET

GET

Change setting to desired value.

Read projector internal setup value.

Increment setup value by 1.

Decrement setup value by 1.

Run a command.

INCREMENT

DECREMENT

EXECUTE

TECHNICAL_D-_o6_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Requesting projector status (Get command)

(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)

from the computer to the projector.

(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.

Changing the projector settings (Set command)

(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2

bytes)) from the computer to the projector.

(2) The projector changes the setting based on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Using the projector default settings (Reset Command)

(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2

bytes) +‘00H’+‘00H’) to the projector.

(2) The projector changes the specified setting to the default value.

(3) The projector returns the response code ‘06H’ to the computer.

Increasing the projector setting value (Increment command)

(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)

+‘00H’+‘00H’) to the projector.

(2) The projector in creases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

Decreasing the projector setting value (Decrement command)

(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)

+‘00H’ + ‘00H’) to the projector.

(2) The projector decreases the setting value on the above setting code.

(3) The projector returns the response code ‘06H’ to the computer.

When a command sent by the projector cannot be understood by the computer

When the command sent by the projector cannot be understood, the error command ‘15H’ is

returned by the computer. Some times, the projector ignores RS-232C commands during other

works. If the error command ‘15H’ is returned, please send the same command again.

When data sent by the projector cannot be practice

When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is

returned.

When the data length is greater than indicated by the data length code, the projector will ignore the

excess data code.

Conversely, when the data length is shorter than indicated by the data length code, an error code

will be returned to the projector.

NOTE • Operation cannot be guaranteed when the projector receives an undefined command or

data.

•

Provide an interval of at least 40ms between the response code and any other code.

• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.

Ignore this data.

• Commands are not accepted during warm-up.

TECHNICAL - 7

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Red

Orange

Green

Blue

BE EF

06 00 3B D3 01 00 00 30

06 00 AB D2 01 00 00 30

06 00 5B D2 01 00 00 30

06 00 CB D3 01 00 00 30

06 00 FB D1 01 00 00 30

06 00 6B D0 01 00 00 30

06 00 9B D0 01 00 00 30

06 00 FB CA 01 00 00 30

06 00 FB E2 01 00 00 30

06 00 08 D3 02 00 00 30

06 00 C7 D2 01 00 01 30

06 00 57 D3 01 00 01 30

06 00 A7 D3 01 00 01 30

06 00 37 D2 01 00 01 30

06 00 F4 D2 02 00 01 30

06 00 83 D2 01 00 02 30

06 00 13 D3 01 00 02 30

06 00 B0 D2 02 00 02 30

06 00 7F D3 01 00 03 30

06 00 EF D2 01 00 03 30

06 00 1F D2 01 00 03 30

06 00 8F D3 01 00 03 30

06 00 BF D1 01 00 03 30

06 00 2F D0 01 00 03 30

06 00 DF D0 01 00 03 30

06 00 4C D3 02 00 03 30

06 00 0B D2 01 00 04 30

06 00 9B D3 01 00 04 30

06 00 CB CB 01 00 04 30

06 00 38 D2 02 00 04 30

06 00 F7 D3 01 00 05 30

06 00 67 D2 01 00 05 30

06 00 97 D2 01 00 05 30

06 00 07 D3 01 00 05 30

06 00 37 D1 01 00 05 30

06 00 A7 D0 01 00 05 30

06 00 57 D0 01 00 05 30

06 00 C7 D1 01 00 05 30

06 00 37 D4 01 00 05 30

06 00 C4 D3 02 00 05 30

00 00

01 00

02 00

03 00

04 00

05 00

06 00

20 00

40 00

00 00

01 00

02 00

03 00

00 00

01 00

00 00

01 00

02 00

03 00

04 00

05 00

06 00

00 00

01 00

20 00

00 00

01 00

02 00

03 00

04 00

05 00

06 00

07 00

08 00

00 00

Purple

White

Set

Blank Color

Black

MyScreen

ORIGNAL

Get

Normal

H Inverse

V lnverse

H&V Inverse

Get

Set

Mirror

Normal

Freeze

Get

Freeze

Red

Orange

Green

Set

Blue

Menu Color

Purple

Transparent

Gray

Get

ORIGNAL

OFF

Startup

MyScreen

Get

English

Français

Deutsch

Español

Italiano

Norsk

Set

Language

Nederlands

Português

Japanese

Get

TECHNICAL_D-_o8_{wnload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Get

BE EF

06 00 7C D2 02 00 07 30

06 00 1A D2 04 00 07 30

06 00 CB D3 05 00 07 30

06 00 08 86 02 00 10 31

06 00 6E 86 04 00 10 31

06 00 BF 87 05 00 10 31

06 00 58 D3 06 00 00 70

06 00 A4 D2 06 00 01 70

06 00 E0 D2 06 00 02 70

06 00 IC D3 06 00 03 70

06 00 68 D2 06 00 04 70

06 00 94 D3 06 00 05 70

06 00 D0 D3 06 00 06 70

06 00 C4 D0 06 00 09 70

06 00 80 D0 06 00 0A 70

06 00 7C D1 06 00 0B 70

06 00 08 D0 06 00 0C 70

06 00 98 D8 06 00 20 70

06 00 91 D0 06 00 0A 20

06 00 FB D8 01 00 20 30

06 00 6B D9 01 00 20 30

06 00 C8 D8 02 00 20 30

06 00 D9 D8 02 00 20 60

00 00

01 00

00 00

Magnify

Increment

Decrement

Get

Auto off

Increment

Decrement

Execute

Brightness Reset

Contrast Reset

V.Position Reset

H.Position Reset

H.Size Reset

Color Balance R Reset

Color Balance B Reset

Sharpness Reset

Color Reset

Tint Reset

Keystone_V Reset

Keystone_H Reset

Auto

off

Set

Blank on/off

Get

(Example of Return)

00 00 01 00

(Normal) (Cover-error)

02 00

03 00

(Lamp-error)

Error Status

Power

(Fan-error)

04 00

(Temp-error)

05 00

(Air flow-error)

06 00

(Lamp-Time-over)

OFF

BE EF

06 00 2A D3 01 00 00 60

06 00 BA D2 01 00 00 60

06 00 19 D3 02 00 00 60

00 00

01 00

00 00

Set

Get

RGB1

RGB2

BE EF

06 00 FE D2 01 00 00 20

06 00 3E D0 01 00 00 20

06 00 0E D2 01 00 00 20

06 00 6E D3 01 00 00 20

06 00 9E D3 01 00 00 20

06 00 AE D1 01 00 00 20

06 00 CD D2 02 00 00 20

06 00 31 D3 02 00 01 20

06 00 57 D3 04 00 01 20

00 00

04 00

03 00

01 00

02 00

05 00

00 00

DVI

Set

Input Source

Video

SVideo

Component BE EF

Get

BE EF

Increment

Volume

Decrement

BE EF

06 00 86 D2 05 00 01 20

00 00

TECHNICAL - 9

Download from Www.Somanuals.com. All Manuals Search And Download.

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Mute

Operation type

Normal

Header

CRC Action

BE EF

06 00 46 D3 01 00 02 20

06 00 D6 D2 01 00 02 20

06 00 75 D3 02 00 02 20

06 00 89 D2 02 00 03 20

06 00 EF D2 04 00 03 20

06 00 3E D3 05 00 03 20

06 00 FD D3 02 00 04 20

06 00 9B D3 04 00 04 20

06 00 4A D2 05 00 04 20

06 00 01 D2 02 00 05 20

06 00 67 D2 04 00 05 20

06 00 B6 D3 05 00 05 20

06 00 45 D2 02 00 06 20

06 00 23 D2 04 00 06 20

06 00 F2 D3 05 00 06 20

06 00 B9 D3 02 00 07 20

06 00 DF D3 04 00 07 20

06 00 0E D2 05 00 07 20

00 00

01 00

00 00

Set

Mute

Get

Brightness

Contrast

Increment

Decrement

Get

Increment

Decrement

Get

Color

Balance R

Increment

Decrement

Get

Color

Balance B

Increment

Decrement

Get

Increment

Decrement

Keystone_V

Keystone_H

Get

BE EF

06 00 E9 D0 02 00 0B 20

06 00 8F D0 04 00 0B 20

06 00 5E D1 05 00 0B 20

00 00

Increment

Decrement

4:3, Full

16:9

BE EF

06 00 9E D0 01 00 08 20

06 00 0E D1 01 00 08 20

06 00 FE D1 01 00 08 20

06 00 AD D0 02 00 08 20

06 00 62 D1 01 00 09 20

06 00 F2 D0 01 00 09 20

06 00 02 D0 01 00 09 20

06 00 51 D1 02 00 09 20

06 00 0D 83 02 00 00 21

06 00 6B 83 04 00 00 21

06 00 BA 82 05 00 00 21

06 00 F1 82 02 00 01 21

06 00 97 82 04 00 01 21

06 00 46 83 05 00 01 21

06 00 B5 82 02 00 02 21

06 00 D3 82 04 00 02 21

06 00 02 83 05 00 02 21

06 00 49 83 02 00 03 21

06 00 2F 83 04 00 03 21

06 00 FE 82 05 00 03 21

00 00

01 00

02 00

00 00

01 00

02 00

00 00

Set

Aspect

Small

Get

Default

Bottom

Top

Display

Position at

16 : 9 or Small

Get

V.Position

H.Position

H.Size

Increment

Decrement

Get

Increment

Decrement

Get

Increment

Decrement

Get

Increment

Decrement

H.Phase

TECHNICAL_D-_o1_w0_{nload from Www.Somanuals.com. All Manuals Search And Download.}

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

Get

BE EF

06 00 F1 72 02 00 01 22

06 00 97 72 04 00 01 22

06 00 46 73 05 00 01 22

06 00 B5 72 02 00 02 22

06 00 D3 72 04 00 02 22

06 00 02 73 05 00 02 22

00 00

Sharpness

Increment

Decrement

Get

Increment

Decrement

Color

Tint

Get

Increment

Decrement

Auto

BE EF

06 00 49 73 02 00 03 22

06 00 2F 73 04 00 03 22

06 00 FE 72 05 00 03 22

06 00 9E 75 01 00 00 22

06 00 FE 71 01 00 00 22

06 00 6E 70 01 00 00 22

06 00 6E 75 01 00 00 22

06 00 5E 72 01 00 00 22

06 00 FE 74 01 00 00 22

06 00 0E 71 01 00 00 22

00 00

0A 00

04 00

05 00

09 00

02 00

08 00

07 00

NTSC

PAL

SECAM

NTSC 4.43

M-PAL

Set

Video Format

N-PAL

Get

BE EF

06 00 0D 73 02 00 00 22

00 00

1080i

1035i

BE EF

06 00 F2 73 01 00 05 22

06 00 62 72 01 00 05 22

06 00 C1 73 02 00 05 22

06 00 FE 22 01 00 00 23

06 00 6E 23 01 00 00 23

06 00 9E 23 01 00 00 23

06 00 CD 22 02 00 00 23

06 00 02 23 01 00 01 23

06 00 92 22 01 00 01 23

06 00 62 22 01 00 01 23

06 00 F2 23 01 00 01 23

00 00

01 00

00 00

01 00

02 00

00 00

01 00

03 00

02 00

Set

HDTV

Get

off

Large

PinP Size

Small

Get

Upper left

Upper right

bottom left

bottom right

Set

PinP Position

Get

BE EF

06 00 31 23 02 00 01 23

06 00 BA 22 01 00 03 23

06 00 2A 23 01 00 03 23

06 00 89 22 02 00 03 23

06 00 D6 22 01 00 02 23

06 00 26 22 01 00 02 23

00 00

01 00

00 00

01 00

02 00

RGB

Video

Get

Set

PinP Audio ch

PinP Input

Video

S-Video

Get

BE EF

06 00 75 23 02 00 02 23

00 00

_{Download from Www.Somanuals.com. All Manuals Search And Dow}T_nlE_oaC_d.HNICAL - 11

TECHNICAL (continued)

Command data chart

Command data

Type Setting code

Names

Operation type

Header

CRC

Action

off

BE EF

06 00 CB D0 01 00 08 30

06 00 5B D1 01 00 08 30

06 00 68 D1 02 00 08 30

01 00

00 00

Set

Sync on G

Get

NORMAL

WHISPER

Get

BE EF

06 00 3B 23 01 00 00 33

06 00 AB 22 01 00 00 33

06 00 08 23 02 00 00 33

06 00 C7 F0 01 00 A1 30

06 00 57 F1 01 00 A1 30

06 00 A7 F1 01 00 A1 30

06 00 F4 F0 02 00 A1 30

06 00 FF 32 01 00 00 26

06 00 6F 33 01 00 00 26

06 00 CC 32 02 00 00 26

06 00 03 33 01 00 01 26

06 00 93 32 01 00 01 26

06 00 30 33 02 00 01 26

06 00 47 33 01 00 02 26

06 00 D7 32 01 00 02 26

00 00

01 00

00 00

01 00

02 00

00 00

01 00

00 00

01 00

00 00

01 00

WHISPER

GAMMA

NORMAL

CINEMA

DYNAMIC

Get

Set

off

Set

IR Remote Front

IR Remote Rear

Get

off

Get

off

IR Remote Top

Get

BE EF

06 00 74 33 02 00 02 26

00 00

NOTE • The max. 2 IR remote out of 3 (front, rear and top) can be activated.

TECHNICAL_D-_o1_w2_{nload from Www.Somanuals.com. All Manuals Search And Download.}

REGULATORY NOTICES

FCC Statement Warning

WARNING: This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or more of

the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements

of FCC (Federal Communication Commission) equipment provided that the

following conditions are met.

The cables may have to be used with the core set to the projector side. Use

the cables which are included with the projector or specified.

Core

CAUTION: Changes or modifications not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Pour les utilisateurs au Canada

AVIS: Cet appareil numérique de la Classe B est conforme à la norme NMB-003 du

Canada.

REGULATORY NOTICES - 1

Download from Www.Somanuals.com. All Manuals Search And Download.

LEGAL INFORMATION

FIVE-YEAR LIMITED WARRANTY

This Dukane LCD projector is warranted to the original purchaser for a period of

five (5) years from the original purchase date - in normal use and service -

against defects in material and workmanship. DUKANE CORPORATION

EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

During the warranty period, Dukane Corporation will repair or replace (at the

manufacturer's option) any such defective parts (except for the lamp, which is

subject to whatever warranties the manufacturer may provide) without charge to

the purchaser for parts or labor when the product is returned, prepaid and insured,

with proof-of-purchase date. This remedy is void if the product has been

damaged by accident, unreasonable use, neglect, improper service or other

causes not arising out of defects in material or workmanship.

Dukane Corporation disclaims all liability for incidental or consequential damage

of any kind, including all damages arising out of any interruptions in operation of

the product and all damages to software.

No person, firm, or representative is authorized to assume any obligation or to

make any warranty on behalf of the Dukane Corporation other than as stated

above.

THIS LIMITED WARRANTY IS VALID FOR U.S.A AND CANADA.

FOR OTHER LOCATIONS, LOCAL WARRANTIES APPLY.

LAMP REPLACEMENT SERVICE & REPAIR POLICY & PROCEDURE

For service and parts, contact the Dukane AV Service Department

at 1 (800) 676-2487 within the USA or 1 (630) 584-2300 worldwide.

If you would like to send a facsimile (FAX), dial 1 (630) 584-5156 worldwide.

When requesting warranty service, please have the sales receipt available along

with the model name and serial number.

If it becomes necessary to return the projector, use the original packing material

and box (if retained) or pack securely. Dukane Corporation will not be liable for

any pick-up or delivery charges or any expenses incurred for service calls or

service supplied by anyone other than the Dukane AV Service Department.

Download from Www.Somanuals.com. All Manuals Search And Download.

Audio Visual Products

Dukane Corporation

Audio Visual Products Division

2900 Dukane Drive

St. Charles, IL 60174-3395

E-mail: [email protected]

Phone: (630) 584-2300

Orders: (800) 676-2485

Information: (800) 676-2486

Fax: (630) 584-5156

Parts & Service: (800) 676-2487

Fax: (630) 584-0984

Download from Www.Somanuals.com. All Manuals Search And Download.

Part # 401-584-00

Cooper Bussmann Soldering Gun BP860 User Manual
Cornelius Beverage Dispenser D45 User Manual
Cuisinart Kitchen Grill WM SW2N User Manual
Dell All in One Printer 946 User Manual
Desa Outdoor Fireplace VSGF28NVA User Manual
Dixon Lawn Mower ZTR 5017Twin User Manual
Dukane Projector 7707 Series User Manual
Fellowes Paper Shredder MS 450Cs User Manual
Fisher Price Model Vehicle x0018 User Manual
GE Monogram Ventilation Hood ZV830SM User Manual