H - 63377
®
Velpar L
herbicide
®
“......... A Growing Partnership With Nature”
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONARY STATEMENTS(continued)
PERSONAL PROTECTIVE EQUIPMENT
Applicators and other handlers must wear:
Long-sleeved shirt and long pants.
Shoes plus socks.
Velpar® L
Protective eyewear.
herbicide
Discard clothing and other absorbent materials that have
been drenched or heavily contaminated with this product's
concentrate. Do not reuse them. Follow manufacturer's
instructions for cleaning/maintaining PPE. If no such
instructions for washables, use detergent and hot water.
Keep and wash PPE separately from other laundry.
Water Dispersible Liquid
Contains 2 Lbs Active Ingredient Per Gallon
Active Ingredient
By Weight
USER SAFETY RECOMMENDATIONS
USERS SHOULD: Wash hands before eating, drinking,
chewing gum, using tobacco or using the toilet.
Hexazinone
[3-cyclohexyl-6-(dimethylamino)
-1-methyl-1,3,5-triazine-2,4(1H,3H)-dione]
25%
75%
ENVIRONMENTAL HAZARDS
Inert Ingredients
Do not apply directly to water, or to areas where surface
water is present or to intertidal areas below the mean high
water mark. Do not contaminate water when disposing of
equipment washwaters.
TOTAL
100%
EPA Reg. No. 352-392
The active ingredient, hexazinone, in this product is
known to leach through soil into ground water under
certain conditions as a result of agricultural use. Use of
this chemical in areas where soils are permeable, partic-
ularly where the water table is shallow, may result in
ground-water contamination.
KEEP OUT OF REACH OF CHILDREN
DANGER
PELIGRO
Si usted no entiende la etiqueta, busque a alguien para que
se la explique a usted en detalle. (If you do not understand
this label, find someone to explain it to you in detail.)
PHYSICAL AND CHEMICAL HAZARDS
STATEMENT OF
FLAMMABLE. Keep away from heat, sparks, and open
PRACTICAL TREATMENT
flames. Keep container closed.
IF IN EYES: Hold eyelids open and flush with steady, gentle
stream of water for 15 minutes. Get medical attention.
GENERAL INFORMATION
IF ON SKIN: Wash with plenty of soap and water. Get
medical attention if irritation persists.
DuPont VELPAR® L Herbicide is a water-dispersible liquid
that is mixed in water and applied as a spray for weed
control in certain crops, Christmas trees, forestry site
preparation and release areas, and industrial areas. It may
also be applied undiluted as a basal soil treatment for brush
control in reforestation areas, rangeland, pastures and
noncrop areas, or by stem injection for brush control.
IF SWALLOWED: Call a physician or poison control
center. Do not induce vomiting. Drink promptly a large
quantity of milk, egg whites, gelatin solution or if these are
not available, drink large quantities of water. Avoid
alcohol.
VELPAR L is an effective general herbicide providing both
contact and residual control of many annual, biennial and
perennial weeds and woody plants.
NOTE TO PHYSICIAN: Probable mucosal damage
may contraindicate the use of gastric lavage.
For medical emergencies involving this product,
call toll free 1-800-441-3637.
VELPAR L is noncorrosive to equipment.
PRECAUTIONARY STATEMENTS
HAZARDS TO HUMANS
AND DOMESTIC ANIMALS
DANGER! CAUSES EYE DAMAGE.
Corrosive, causes irreversible eye damage. Harmful if
swallowed. Do not get in eyes or on clothing. Wash
thoroughly with soap and water after handling.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
ENVIRONMENTAL CONDITIONS
AND BIOLOGICAL ACTIVITY
DIRECTIONS FOR USE
It is a violation of federal law to use this product in a manner
inconsistent with its labeling.
VELPAR L is absorbed through the roots and foliage.
Moisture is required to activate VELPAR L in the soil. Best
results are obtained when the soil is moist at the time of
application and 1/4–1/2" of rainfall occurs within 2 weeks
after application.
VELPAR L should be used only in accordance with recommen-
dations on this label, or in supplemental DuPont publications.
Do not apply this product in a way that will contact workers or
other persons, either directly or through drift. Only protected
handlers may be in the area during application. For any
requirements specific to your state or tribe, consult the agency
responsible for pesticide regulation.
Apply VELPAR L preemergence or postemergence when weeds
are less than 2" in height or diameter. Foliar activity is most
effective under conditions of high temperature (above 80 °F),
high humidity, and good soil moisture. Foliar activity may be
reduced when vegetation is dormant, semi-dormant, or under
stress.
The correct use rates by crop and geographical area,
specified on this label, and proper mixing/loading site
considerations and application procedures must be followed
to minimize potential for hexazinone movement into ground
water. Users are encouraged to consult with their state
Department of Agriculture, Extension Service, or other
pesticide lead agency for information regarding soil
permeability, aquifer vulnerability, and best management
practices for their area.
On herbaceous plants, symptoms usually appear within 2 weeks
after application under warm, humid conditions, while 4–6
weeks may be required when weather is cool or dry, or when
plants are under stress. If rainfall after application is inadequate
to activate VELPAR L in the soil, plants may recover from
contact effects and continue to grow.
On woody plants, symptoms usually appear within 3–6 weeks
after sufficient rainfall has carried the herbicide into the root
zone during periods of active growth. Defoliation and refoliation
may occur, but susceptible plants are killed.
AGRICULTURAL USES
AGRICULTURAL USE REQUIREMENTS
Use this product only in accordance with its labeling and
with the Worker Protection Standard, 40 CFR part 170.
This Standard contains requirements for the protection of
agricultural workers on farms, forests, nurseries, and
greenhouses, and handlers of agricultural pesticides. It
contains requirements for training, decontamination, notifi-
cation, and emergency assistance. It also contains specific
instructions and exceptions pertaining to the statements on
this label about personal protective equipment(PPE) and
restricted-entry interval. The requirements in this box only
apply to uses of this product that are covered by the Worker
Protection Standard.
The degree and duration of control may depend on the following:
• Use rate
• Weed spectrum and size at application
• Environmental conditions at and following treatment
Where a rate range is shown, use the higher levels of the dosage
range on hard-to-control species, fine-textured soils, or soils
containing greater than 5% organic matter or carbon. Use the
lower levels of the dosage range on coarse-textured soils and/or
on soils low in organic matter. Refer to specific uses for rate
ranges.
WEED RESISTANCE MANAGEMENT
Do not apply this product in a way that will contact workers
or other persons, either directly or through drift. Only
protected handlers may be in the area during application.
When herbicides with the same mode of action are used
repeatedly over several years to control the same weed species
in the same field, naturally occurring resistant weed biotypes
may survive a correctly applied herbicide treatment, propagate,
and become dominant in that field. These resistant weed
biotypes may not be adequately controlled. Cultural practices
such as tillage, preventing weed escapes from going to seed, and
using herbicides with different modes of action within and
between crop seasons can aid in delaying the proliferation and
possible dominance of herbicide resistant weed biotypes.
Do not enter or allow worker entry into treated areas during
the restricted entry interval(REI) of 24 hours.
PPE required for early entry to treated areas that is
permitted under the Worker Protection Standard and that
involves contact with anything that has been treated, such as
plants, soil, or water, is :
Coveralls
Waterproof gloves
Shoes plus socks
Protective eyewear
APPLICATION INFORMATION
VELPAR L may be applied by ground equipment and, where
permitted, aerial equipment. Use rates, minimum spray
gallonage, and other application information are described for
the various uses.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WEEDS CONTROLLED
ALFALFA
VELPAR L, when applied preemergence or early
postemergence at the following rates, will control these
species:
VELPAR L is recommended for control of certain weeds in
established alfalfa grown for hay, except in the states of North
Dakota and South Dakota. Do not use on alfalfa grown for
seed in any state except California.
1–2 Pt/Acre
Tansy-mustard
2–4 Pt/Acre
APPLICATION TIMING
NONDORMANT AND SEMI-DORMANT VARIETIES
In the following states, make a single application during winter
months when alfalfa plants are in the least active stage of
growth:
Annual bluegrass
Blue mustard
Jim Hill mustard
London rocket
Arizona
California
Colorado
Idaho
Kansas
New Mexico
Oklahoma
Oregon
Utah
Washington
Wyoming
Cheatgrass (downy brome) Miners lettuce
Montana
Nebraska
Nevada
Common chickweed
Common groundsel
Dogfennel (mayweed)
English catchfly
Fiddleneck (tarweed)
Field pennycress
Filaree
Salsify
Seedling orchardgrass
Shepherd’s-purse
Spurry
Texas
In the following states, make a single application either in the
spring before new growth exceeds 2" in height or to stubble
after cutting following hay removal and before regrowth
exceeds 2" in height:
Connecticut
Delaware
Illinois
Indiana
Iowa
Kentucky
Tansy-mustard
Wild radish
Maine
New Hampshire Vermont
Yellow rocket
Maryland
Massachusetts
Michigan
Minnesota
Missouri
New Jersey
New York
Ohio
Pennsylvania
Rhode Island
Virginia
West Virginia
Wisconsin
Flixweed
4–6 Pt/Acre
Common dandelion*
(i.e. Canada bluegrass)
False dandelion
Perennial bluegrass*
(spring only)
Severe alfalfa injury may result following application after
cutting if either the regrowth is more than 2" high, significant
stubble is left after alfalfa cutting, or the air temperature is above
90 °F.
Prickly lettuce*
Ryegrass, annual
Quackgrass*
Foxtail (Setaria spp)*
Mexican tea*
DORMANT VARIETIES
Seedling alfalfa*
Make a single application after alfalfa becomes dormant and
before new growth begins in the spring. Where weeds have
emerged, use a surfactant.
White cockle*
* Partial control
For the states of Montana and Wyoming, refer to supplemental
labeling for use directions and precautions.
VELPAR L, when applied in late spring or after cutting at
the following rates, will control these species:
USE RATES
2–6 Pt/Acre
Use higher rates on hard-to-control species, fine textured soils,
soils containing greater than 5% organic matter, or under
adverse environmental conditions or when weeds are stressed
due to low rainfall.
Common lambsquarters
Crabgrass
Foxtail (Setaria spp.)
Jimsonweed
Fleabane
Redroot pigweed
Select the appropriate dose for soil texture and organic matter
content as follows:
SPRAY EQUIPMENT
VELPAR L (Pt/Acre)
Apply VELPAR L using a fixed boom power sprayer or
aerial equipment.
Soil Texture
Description
Coarse
Percent Organic Matter in Soil
<1%
1–5%
>5%
MIXING INSTRUCTIONS
Add VELPAR L to a water-filled tank and mix it
thoroughly. Apply it in at least 20 gal of water per acre by
ground or 5 to 10 gal of water per acre by air. Use at least
5 pts of water for every 1 pt of VELPAR L.
Loamy sand, sandy loam 2–3
Medium
2–3
4–6
Loam, silt loam silt, clay
loam,sandy clay loam
2–3
3–6
4–6
Fine
Silty clay loam, sandy
clay, silty clay, clay
3–6
3–6
4–6
Rate restrictions are also noted in Important Precautions and
Seed Alfalfa (California Only).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
- alfalfa is healthy and vigorous, not growing under stress
from insect, disease, winter injury or other types of stress.
REPLANTING (FOLLOWING ALFALFA)
• Do not replant treated areas to any crop except corn, root
crops or sugarcane within two years after treatment, as crop
injury may result.
Injury may result to alfalfa plants that fail to meet these
growth criterion listed above.
• Do not use VELPAR L on seedling alfalfa, alfalfa-grass
mixtures, or other mixed stands as injury may result to the
seedling alfalfa or companion crop.
• Corn may be planted 12 months after the last treatment,
provided the use rate did not exceed 3 pt per acre, except in
areas of low rainfall (20" or less).
• At elevations above 4,000 ft, do not use VELPAR L on
alfalfa that has been established with a cover or nurse crop
until the alfalfa has gone through two summer growing
seasons.
• Root crops such as potatoes, sugarbeets, radish and carrots
may be planted 12 months after last treatment, provided the
use rate not exceed 2 pt per acre. Sites with use rates
higher than 2 pt per acre should not be replanted to any
crop within 2 years of application, or unacceptable crop
injury may result.
• Do not use VELPAR L in low desert valleys in California
or Arizona.
• Sugarcane may be planted any time following treatment.
• Do not exceed 3 pt per acre on alfalfa less than one year
old.
• In California, do not replant seed alfalfa areas to any crop
within two years after treatment, as crop injury may result.
• Do not add a surfactant to VELPAR L when treating
nondormant alfalfa varieties.
IMPORTANT PRECAUTIONS - ALFALFA ONLY
• Do not use VELPAR L on gravelly or rocky soils, exposed
subsoils, hardpan, sand, poorly drained soil, or alkali soils.
Best results are obtained when 1/2–1" of rainfall or sprinkler
irrigation occurs within two weeks after application, when
soil is moist at time of application, and when weeds have not
germinated or are less than 2" in height or diameter. Heavy
rainfall or excessive irrigation after application may result in
crop injury or poor performance of the herbicide.
• Crop injury, including mortality, may result in fields with
restricted root growth due to nonuniform soil profiles
such as gravel bases and clay lenses.
• Do not graze or feed forage or hay to livestock within 30
days following application.
• Do not apply to snow-covered or frozen ground.
• On soils high in organic matter (greater than 5%), the
effectiveness of VELPAR L can be significantly reduced
and weed control may be unsatisfactory.
SEED ALFALFA (CALIFORNIA ONLY) -
ADDITIONAL PRECAUTIONS
• Do not use VELPAR L on fields with sandy loam or
loamy sand soils having less than 1% organic matter.
• Since the effect of VELPAR L on alfalfa varies with soil
conditions, uniformity of application, and environmental
conditions, growers should limit their first use to small
areas.
• Do not exceed 2 pt per acre on fields with sandy loam or
loamy sand soils having 1–2% organic matter.
• Do not exceed 2 pt per acre on seed alfalfa that has been
established for only one growing season.
• If abnormally dry conditions exist following application,
restrict the first irrigation to no more than 1/2 acre inch of
water.
ALFALFA - IMPREGNATION ON
DRY BULK FERTILIZER (EXCEPT
CALIFORNIA AND ARIZONA)
• Temporary yellowing of alfalfa may occur following
VELPAR L applications.
• Treat only stands of alfalfa established for one year or for
one growing season(except in California), provided the
following conditions are met:
Dry bulk fertilizer may be impregnated or coated with
VELPAR L for application to established alfalfa. All
recommendations, cautions and special precautions on this
label must be followed along with state regulations relating to
dry bulk fertilizer blending, impregnating and labeling. Keep
VELPAR L from heat, sparks, and open flame. (Refer to the
material safety data sheet [MSDS] for VELPAR L.)
–The alfalfa root system must be well established.
–The crop must be healthy, vigorous and not under stress
from adverse weather conditions, insect or disease
damage.
–The alfalfa crop must be free of excessive winter injury
from freezing and thawing.
If fertilizer materials are excessively dusty, use a suitable
additive to reduce dust prior to impregnation, as dusty
fertilizer will result in poor distribution during application.
The dry fertilizer must be properly impregnated and
uniformly applied to the alfalfa to avoid crop injury and/or
poor weed control.
• In California, fall planted alfalfa may be treated in the
following winter months with VELPAR L at 1 to 2 pts per
acre to suppress or control Black Mustard, Common
groundsel, London rocket, Shepard’s-purse, Common
chickweed, Fiddleneck or Filaree, provided:
To impregnate the fertilizer, use a system consisting of a
conveyor or closed drum used to blend dry bulk fertilizer. Any
commonly used fertilizer can be impregnated with VELPAR
L, except potassium nitrate or sodium nitrate. Do not use
VELPAR L on limestone.
- alfalfa root growth exceeds 6 inches in length
- vegetative top growth of alfalfa has lateral development of
secondary growth
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Use a minimum of 250 lb dry bulk fertilizer per acre and up to Do not use VELPAR L on Christmas trees in the following
a maximum of 450 lb per acre. To impregnate or coat the dry
bulk fertilizer with VELPAR L, direct the nozzles to deliver a
fine spray towards the fertilizer for thorough coverage while
avoiding spray contact with mixing equipment. Uniform
impregnation of VELPAR L to dry bulk fertilizer will vary,
and if the absorptivity is not adequate, the use of an
absorptive powder may be required to produce a dry, free-
flowing mixture. Microcel E (Johns Manville Product
Corporation) is the recommended absorbent powder. When
another herbicide is used with VELPAR L, mix and
impregnate the fertilizer immediately.
states:
Alabama
Arkansas
Connecticut
Delaware
Georgia
Louisiana
Maine
New Jersey
New York
Texas
Vermont
Maryland
North Carolina Virginia
West Virginia
Massachusetts Pennsylvania
Mississippi Rhode Island
New Hampshire South Carolina
Florida
APPLICATION TIMING
EASTERN US
Apply VELPAR L as a broadcast spray in the spring prior to
conifer bud break. If application is made after conifer bud
break, use directional spray equipment to prevent contact
with conifer foliage.
Apply impregnated fertilizer immediately unless experience
has shown that it can be stored without becoming lumpy and
difficult to spread.
Select the rate of VELPAR L to apply per acre from the
appropriate section of this label. Then refer to the rate chart
below to determine the amount of VELPAR L that should be
impregnated on a ton of dry bulk fertilizer, based on the
amount of fertilizer to be distributed in one acre.
WESTERN US
Areas of greater than 20" annual rainfall - Apply VELPAR
L as a broadcast spray in the spring prior to conifer bud
break. If application is made after bud break, use directional
spray equipment to prevent contact with conifer foliage.
Rate Chart for Impregnating Fertilizer with VELPAR L
Areas of less than 20" annual rainfall - Apply VELPAR L in
the fall before the soil freezes or in the spring after snow
cover melts, but before conifer bud break occurs.
Fertilizer
“Velpar” L Rate Per Acre
Rate/Acre
250 pounds
300 pounds
350 pounds
400 pounds
2 Pints
3 Pints
4 Pints
6 Pints
16 pts/ton
24 pts/ton
32 pts/ton
48 pts/ton
13.4 pts/ton 20 pts/ton
26.8 pts/ton 40.2 pts/ton
USE RATES
11.4 pts/ton 17.2 pts/ton 22.8 pts/ton 34.2 pts/ton
The rates listed below are for broadcast application. For
band application, use proportionately less; for example, use
1/2 of the broadcast rates when treating a 3-ft band where
row spacing is 6 ft.
10 pts/ton
8.8 pts/ton
15 pts/ton
20 pts/ton
30 pts/ton
450 pounds
13.2 pts/ton 17.6 pts/ton 26.4 pts/ton
For rates other than those listed, use the following formula to
calculate the amounts of VELPAR L to be impregnated per
ton of dry fertilizer.
Do not use more than one application of VELPAR L per
year.
Soil Texture
Description
Coarse
VELPAR L (Pt/Acre)
Pints
Pints
First Year Plantings Established Trees
2000
VELPAR L X
Per acre
=
VELPAR L Per
Ton of Fertilizer
Lbs Fertilizer Per Acre
Loamy sand,
sandy loam
(50-85% sand)
APPLICATION
4
4–5
5–7
Uniform application of VELPAR L-impregnated dry
fertilizer is essential for satisfactory weed control. Accurate
calibration of the application equipment is essential for
uniform distribution to the surface. The recommended
method of application is to apply 1/2 the recommended rate
and overlap 50%. This results in the best distribution
pattern.
Medium
Loam, silt loam
silt, clay loam,
sandy clay loam
4–5
Fine
Silty clay loam,
clay loam,
sandy clay,
silty clay, clay
CHRISTMAS TREES
5–6
7–8
VELPAR L is recommended for control of certain weeds
where the following species are grown:
First year plantings - Transplant stock that is 2 years old or
more (1 year old for loblolly pine). Apply VELPAR L only
if rainfall has settled the soil around the base and root
systems of the transplants.
Austrian pine
Douglas fir
Noble fir
Ponderosa pine
Scotch pine
Sitka spruce
Established trees - Trees that have been planted in the
plantation for 1 year or more.
(western US only)
Grand fir
Loblolly pine
5
Download from Www.Somanuals.com. All Manuals Search And Download.
WEEDS CONTROLLED
PINEAPPLE
Annual bluegrass
Barnyardgrass
Bentgrass
Fleabane
VELPAR L is recommended for control of certain weeds in
pineapple.
Foxtail
Goldenrod*
Heath aster*
APPLICATION TIMING
- USE RATES - MIXING INSTRUCTIONS
Bromegrass
Catsear* (false dandelion) Horseweed*
Use a sprayer properly calibrated to a constant speed and
rate of delivery.
Common groundsel
Common ragweed
Crabgrass*
Orchardgrass*
Oxeye daisy
Mix the proper amount of VELPAR L in water. Add a
surfactant at 0.25% by volume of water.
Pennsylvania smartweed
Ryegrass*
Curly dock*
• Intercrop period - Apply VELPAR L as a broadcast spray
in 100–400 gal of water per acre at the rate of 0.9–7 pt per
acre. For aerial application, use at least 10 gal water per
acre.
Dandelion*
Velvetgrass
Fescue*
Wild carrot*
Fireweed (willowweed)*
• Post mulch, preplant - Apply VELPAR L as a broadcast
spray in 100–400 gal of water per acre at the rate of 0.9–7
pt per acre.
* Partial control
SPRAY EQUIPMENT
• Post plant, before planting material starts active growth -
Apply VELPAR L as a broadcast spray in 100–400 gal of
water per acre at the rate of 0.9–7 pt per acre.
VELPAR L may be applied by ground equipment or by air
(helicopter only).
MIXING INSTRUCTIONS
A post-plant application should be made after planting
material starts to grow only when weed growth has
escaped control by other herbicide applications.
Select a spray volume that will ensure a thorough and uniform
application. Use at least 5 gal of water for every 1 gal of
VELPAR L.
• Post-plant crop harvest, prior to forcing first ratoon -
Apply VELPAR L as a broadcast spray in 100–400 gal of
water per acre at the rate of 0.9–7 pt per acre.
IMPORTANT PRECAUTIONS
- CHRISTMAS TREES
• Directed postemergence (pineapple and weeds) inter-
space application - Apply VELPAR L as a directed spray
3–10 months after planting in 50–200 gal of water per
acre (broadcast basis) at the rate of 0.9–7 pt per acre
(broadcast basis) using a stroller boom or knapsack.
• Do not use VELPAR L in nurseries, seed beds, or ornamental
plantings.
• Do not add a surfactant in applications over the top of
conifers.
• Weed control results from spring applications depend on
sufficient moisture to activate VELPAR L.
• Directed spot treatments for perennial grasses before
floral induction - Spray perennial grasses postemergence
to wet (50–200 gals per acre depending on size) with
3.5–7 pt per 100 gal of water as a spot treatment.
• Do not cut treated vegetation for forage or hay nor graze
domestic animals on treated areas for 60 days following
application.
• Treatments to field edges and roadsides - Apply VELPAR L
at 7–14.5 pt per acre in 100–400 gal of water.
• Poor weed and brush control may result from the following:
–Heavy duff or slash present at the time of application.
–Use on poorly drained sites.
WEEDS CONTROLLED
VELPAR L is recommended for the control or suppression
of the following weeds:
–Applications made when soil is saturated with water and rain
is imminent within 24 hours.
–Applications to soils high in organic matter (greater
than 5%).
Ageratum
Kao haole*
Mauna loa*
Morningglory
Oxalis
Balsam apple
Castor bean
Crabgrass
• Crop injury may occur when VELPAR L is used on the
following:
–Trees that show poor vigor, insect damage, disease, winter
injury, or other stress conditions.
Crotalaria
Popolo
Dallisgrass
Guinea grass
Jungle rice
Richardsonium
Vaseygrass
–Any soil containing less than 1% organic matter.
–Loamy sand or sandy loam with less than 2% organic matter
(except Jeffrey Pine and Ponderosa Pine).
–Crop species not listed in this label.
* Suppression
–Conifer foliage after conifer bud break.
–Gravelly or rocky soils, exposed subsoils, clay knobs, sand,
or sandy soil with 85% or more sand.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
PUERTO RICO
IMPORTANT PRECAUTIONS - PINEAPPLE
For preemergence treatments, apply 0.9–1.8 pt of VELPAR L
per acre.
• Use the lower rates on coarse-textured soils or in areas
where rainfall exceeds 65" per year.
For postemergence treatments, apply 0.9–1.8 pt of VELPAR L
per acre to weeds after they have emerged. Use the lower
rates on coarse-textured soils and the higher rates on fine-
textured soils (high in clay or organic matter). Each ratoon
may receive up to 1.8 pt of VELPAR L per acre.
• Use the higher rates on fine-textured soils or in areas
where rainfall is less than 65" per year.
• Do not exceed 1.8 gal VELPAR L per acre per crop.
• Do not apply VELPAR L within 181 days of harvest.
For spot treatment of emerged weeds, VELPAR L may be
applied with a knapsack sprayer in concentrations of
0.9–1.8 pt per 100 gal of water. Apply a sufficient volume to
wet the weed foliage. Do not exceed 100 gal of spray per
treated acre. Use the lower concentration on coarse-textured
soils and the higher concentration on fine-textured soils.
SUGARCANE
VELPAR L is recommended for selective weed control in
sugarcane except in the State of Florida.
APPLICATION TIMING
- USE RATES - MIXING INSTRUCTIONS
Note: Since it is difficult to calibrate “spot” knapsack
applications, extra care must be taken not to exceed the rate
equivalent of the maximum of 1.8 pt VELPAR L per acre.
Apply a single treatment of VELPAR L per year using a
fixed-boom sprayer and a minimum of 25 gal of spray per
acre unless otherwise directed.
Do not apply more than 3.6 pt of VELPAR L per acre per
crop.
HAWAII
Apply VELPAR L pre- or postemergence at the following
rates for the indicated soil texture:
TEXAS
Apply 1.8–7 pt of VELPAR L per acre. On plant cane, apply
the herbicide before the cane emerges or as a directed layby
treatment. On stubble cane, apply VELPAR L preemergence
(up to the 3-leaf stage) or as a directed layby treatment. A
pre- or early postemergence treatment may be followed by a
layby treatment, provided at least 60 days have elapsed and
3" of rainfall or sprinkler irrigation have occurred since the
first treatment.
VELPAR L (Pt/Acre)
Soil Texture
Description
Coarse
(Plus surfactant
0.25% by volume)
Sand, loamy sand, sandy loam
Medium
1.8–3.5
1.8–7.0
7.0–14.5
Loam, silt loam, silty clay loam
Fine
Do not apply more than 7 pt of VELPAR L per acre per crop.
Use the following rates for the soil texture:
Clay, gray hydromorphic clay
Soil Texture
Description
VELPAR L (Pt/Acre)
Preemergence Layby
Use the higher levels of the recommended dosage ranges on
soils high in organic matter. Do not apply more than twice
the highest recommended rate for the indicated soil texture
per crop (18–24 months).
+
Coarse*
Sandy loam
Medium
1.8
2.7
3.5
1.8
2.7
3.5
A surfactant is recommended for all uses.
For preemergence use only, VELPAR L may be applied
with aerial equipment using at least 10 gal of spray per acre.
Loam, silt loam
Fine
For spot treatments of emerged weeds, VELPAR L may be
applied with a knapsack sprayer in concentrations of 1.8–14
pt per 100 gal of water. Apply a sufficient volume to
thoroughly wet weed foliage, but do not exceed 40 gal of
spray per treated acre. Use the lower concentrations on
coarse-textured soils that are low in organic matter, and use
the higher concentrations on fine-textured soils that are high
in organic matter.
Clay loam
* With at least 2% organic matter
On dormant cane, a surfactant may be added to the spray
mixture to increase control of emerged weeds.
LOUISIANA
Apply 1.8–3.5 pt of VELPAR L per acre broadcast in the
fall before sugarcane emerges or in the spring before active
cane tillering begins. Fall treatments of 1.8–3 pt per acre
may be followed by a spring treatment of 1.8–3 pt per acre.
Do not apply more than 6 pt per year. Use the higher levels
of the recommended dosage range on fine-textured soils.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
WEEDS CONTROLLED
FORESTRY
Ageratum*
Alexandergrass
Johnsongrass (from seed)
Jungle rice
SITE PREPARATION
VELPAR L is recommended for weed and brush control in areas
where the following species are grown:
Amaranth (slender,
Lambsquarter
Morningglory (hairy,
threelobe)
Mustard (wild)
Oxalis
Panicum (brownleaf,
browntop, Texas millet)
Paspalum (ricegrass, sour)
Pigweed (common,
smooth)
Popolo
Purslane
Sandbur
Sensitive plant (hila hila)
Signalgrass (broadleaf)
Sowthistle
Spanish needle
Sprangletop
Spurge (prostrate,
graceful)
Sunflower
smooth)
American burnweed
(fireweed)
EASTERN US AND LAKE STATES
Balsam apple
Barnyardgrass
Bermudagrass*
Carolina geranium
Chickweed
Crabgrass (hairy, large,
smooth)
Crotalaria (fuzzy, showy)
Cuphea (tarweed)
Dallisgrass
Austrian pine
Balsam fir
Red spruce
Scotch pine
Shortleaf pine
Slash pine
Virginia pine
White spruce
Black spruce
Loblolly pine
Longleaf pine
Ponderosa pine
Red pine
WESTERN US
Fingergrass (radiate,
swollen)
Blue spruce
Douglas fir
Engleman spruce
Grand fir
Lodgepole pine
Noble fir
Ponderosa pine
Sitka spruce
White fir
Flora’s paintbrush
Foxtail (bristly, yellow)
Goosegrass
Guineagrass
Henbit
Jeffrey pine
Itchgrass*
Jobs tears
Vaseygrass
Waltheria (hialoa)
APPLICATION TIMING
EASTERN US
Apply VELPAR L from early spring to early summer after
* Partial control
hardwoods have broken bud and before the foliage has hardened
off.
IMPORTANT PRECAUTIONS - SUGARCANE
Do not plant any crop other than sugarcane following an
application of VELPAR L.
WESTERN US
Rainbelt (areas of high spring rainfall): For best results, apply
in late winter or spring when weeds and brush are actively
growing.
Do not feed sugarcane forage to livestock.
Do not apply VELPAR L:
• Within 180 days of harvest in Hawaii.
• Within 234 days of harvest in Louisiana.
• Within 288 days of harvest in Puerto Rico.
• Within 234 days of harvest in Texas.
Snowbelt (areas of low spring rainfall): For best results, apply
in the fall before soil freezes, or in the spring after snow cover
melts in anticipation of rainfall. Weed and brush control results
from spring applications will be dependent on sufficient rainfall
following application to activate VELPAR L.
To avoid injury to sugarcane, observe the following precautions:
USE RATES
• Do not use VELPAR L on cane that shows poor vigor because
of insect damage, disease, or winter injury, or shows
symptoms of other stress conditions such as drought stress.
Use the lower rates on coarse-textured soils and soils low in
organic matter; use the higher rates on fine-textured soils and on
soils high in organic matter. Use the higher rates where hard-to-
kill species predominate.
• Do not add a surfactant in applications unless otherwise
specified or allowed.
The rates listed below are for broadcast application.
• Do not use VELPAR L on gravelly or rocky soils, thinly
covered subsoils, or coarse-textured soils (sands to sandy
loams) with less than 1% organic matter.
Soil Texture
Description
Coarse
VELPAR L (Qt/Acre)
Eastern US
Western US
• Temporary chlorosis of the crop may result from application
over emerged cane. Applications during active cane growth
should be directed to cover the weeds and soil while
minimizing crop contact.
Sand, loamy sand,
sandy loam
Medium
Loam, silt loam,
sandy clay loam
Fine
4–6
6–8
2–2.5
2.5–4
• Do not use VELPAR L on varieties known to be susceptible
to weed killers.
Silty clay loam,
clay loam, sandy clay,
silt, silty clay, clay
Extremely heavy rainfall after application may result in poor
weed control and/or crop injury, especially if the application is
made to dry soil.
8–10
4–6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
PLANTS CONTROLLED
SITE PREPARATION - TANK MIXTURES
VELPAR L PLUS “TORDON101 MIXTURE”1
Herbaceous Plants
For improved, broad-spectrum brush control, tank mix VELPAR
L with TORDON 101 MIXTURE. Consult the VELPAR L
Eastern US site preparation section and TORDON 101
MIXTURE labels for a listing of crop tree species where this
combination can be used.
Annual bluegrass
Asters
Barnyardgrass
Bentgrass
Bromegrass
Canada thistle*
Fleabane
Foxtail
Goldenrod*
Heath aster*
Horseweed*
Orchardgrass*
APPLICATION TIMING
Apply VELPAR L plus TORDON 101 MIXTURE from late
spring to early summer after the trees have reached full leaf, but
before leaf tissue hardens. In the states of Maine, Michigan,
Minnesota, New Hampshire, New York, Vermont, and
Wisconsin, apply this tank mixture after bud break.
Catsear (false dandelion)* Oxeye daisy
Common groundsel
Common ragweed
Crabgrass*
Pennsylvania smartweed*
Pinegrass
Quackgrass*
Ryegrass*
Curly dock*
WOODY PLANTS CONTROLLED - USE RATES
Dandelion*
Elksedge
Fescue*
Squawcarpet
Velvetgrass
Wild carrot
Predominant
Species
VELPAR L
(Qt/Acre)
Tordon 101 M
(Qt/Acre)
Fireweed (willowweed)*
Blackberry, Elm,
Oak (Prunus spp.),
Sweetgum
6-10
4
* Partial control; use higher rates for soil textures indicated above.
Blackgum, Dogwood,
4-10
6-8
Woody Plants
Pine, Red maple,
Sassafras, Sourwood
Ash
Hickory
Aspen (big tooth,
trembling)
Balsam poplar
Birch
Blackgum
Deerbrush ceanothus
Elm
Flowering dogwood*
Greenleaf manzanita
Hawthorne
Honeysuckle*
Oaks
Red maple*
Snowbush ceanothus
(varnishleaf ceanothus)
Sourwood*
Sweetgum
Whitehorn
Wild cherry
Willows
Refer to the use rate table in the VELPAR L Site Preparation
section of this label for recommended rates based on soil
texture. Also refer to the TORDON 101 MIXTURE label for
rates based on species composition. Other weed and brush
species may be controlled by VELPAR L plus TORDON 101
MIXTURE.
SPRAY EQUIPMENT
VELPAR L plus TORDON 101 MIXTURE may be applied by
ground equipment or by air (helicopter only).
MIXING INSTRUCTIONS
Hazel
For ground application, use enough water for thorough
coverage, usually a minimum of 25 gal per acre. For aerial
applications, use at least 5 gal of water per acre. Use at least 5
gal of water for every 1 gal of VELPAR L. For best results, full
foliar coverage is required.
*Partial control; use the higher rates for the soil textures
indicated above.
Within several weeks after VELPAR L activation by rainfall,
affected vegetation may be burned, if desired. This burn may
further enhance control of vegetation. Burn the vegetation
only after any residual stand is completely defoliated, at least
twice, allowing for sufficient root uptake of VELPAR L. In
the West, results may take one to two years in areas of low
rainfall.
IMPORTANT PRECAUTIONS
- VELPAR L + TORDON 101 MIXTURE
• To avoid injury, do not plant pine before the following
intervals following application of Tordon 101 Mixture:
–Southern states - 6 months
–Lake states - 9 months
–Northeastern states - 9 months
SPRAY EQUIPMENT
• Burning treated sites after initial contact (browning) effect on
foliage may result in poor control. Burn the vegetation only
after brush has completely defoliated at least once, allowing
sufficient root uptake of VELPAR L (usually 60-90 days after
adequate rainfall).
VELPAR L may be applied by ground equipment or by air
(helicopter only).
MIXING INSTRUCTIONS
For ground application, use enough water for thorough
coverage, usually a minimum of 25 gal per acre. For aerial
applications, use at least 5 gal of water per acre and at least 5
• Before using Tordon 101 Mixture, read and carefully observe
the cautionary statements and all other information appearing
on the product label. Tordon 101 Mixture is a restricted use
pesticide, for retail sale to and use only by certified
gal of water for every 1 gal of VELPAR L.
applicators or persons under their direct supervision and only
for those uses covered by certified applicator’s certification.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
VELPAR L PLUS “GARLON 4”2
Selection of the rate per acre and grid pattern will depend on
soil texture and woody plant composition. Use the lower
rates on coarse textured soils and when the major
component of the hardwoods are susceptible species. Use
the high rates on fine-textured soils and hard-to-kill species.
For improved, broad-spectrum brush control, tank mix
VELPAR L with GARLON 4. Consult the VELPAR L Eastern
US site preparation section and the GARLON 4 label for a
listing of crop tree species on which this combination can be
used. This tank mix may be used in the following states:
Application Patterns and Rates For Undiluted VELPAR L
ML/Spot
0.6
Grid (Ft) Qt/Acre
Alabama
Arkansas
Delaware
Florida
Maryland
South Carolina
Tennessee
Texas
Coarse
3 X 3
4 X 4
4 X 6
3 X 3
4 X 4
4 X 4
4 X 6
3
Michigan
2.0
6
Minnesota
Mississippi
North Carolina
Oklahoma
3.1
6
Virginia
Medium/Fine
1.6
8
Georgia
Wisconsin
2.8
8
Louisiana
3.5
10
10
APPLICATION TIMING
5.2
Apply VELPAR L plus GARLON 4 from late spring to early
summer after the trees have reached full leaf, but before leaf
tissue hardens.
SINGLE STEM (BASAL SOIL)
Apply undiluted VELPAR L to the soil with an exact
delivery handgun applicator. Apply at the rate of 2–4 ml for
each inch of stem diameter at breast height. Direct the
treatment to the soil within 3 ft of the root collar of woody
plants to be controlled. When treating large stems and when
more than one delivery of VELPAR L is needed per stem,
make application on opposite sides of the stem.
USE RATES
Refer to the use rate table in the Site Preparation section of
this label for recommended rates of VELPAR L based on
soil texture. Mix the recommended rate of VELPAR L with
4–8 qt of GARLON 4 per acre.
SPRAY EQUIPMENT
For multi-stemmed and low-growing brush that have stem
diameters that are difficult to determine, apply VELPAR L
at the rate of 2–4 ml per 3" of canopy width. For tall,
slender (columnar) brush types, apply 4–8 ml per 3" of
height. Base the rate on whichever canopy dimension is
greater (width or height).
Apply VELPAR L plus GARLON 4 by ground equipment
or by air (helicopter only).
MIXING INSTRUCTIONS
For ground application, use enough water for thorough
coverage, usually a minimum of 25 gal per acre. For aerial
applications, use at least 12 gal of water per acre.
When treating brush that requires more than a single 4 ml
application of VELPAR L, apply subsequent applications
equally spaced around the plant. If treating brush on sloped
sites, apply most of the VELPAR L on the uphill side of the
stem. If treating resprouts from brush disturbed by cutting
or shredding, the rate of application should be proportional
to the original tree size, not just the small regrowth of
sprouts.
For best results, full foliar coverage is required.
IMPORTANT PRECAUTIONS
- VELPAR L + GARLON 4
• Conifers planted sooner than two months after treatment
with GARLON 4 at 1–2 gal per acre may be injured.
• Burning treated sites after initial contact (browning) effect
on foliage may result in poor control. Burn the vegetation
only after brush has completely defoliated at least once,
allowing sufficient root uptake of VELPAR L (usually 60-
90 days after adequate rainfall).
INJECTION
No Worker Protection Standard worker entry
restrictions or worker notification requirements apply
when this product is directly injected into agricultural
plants.
• Before using GARLON 4, read and carefully observe the
cautionary statements and all other information appearing
on the product label.
Inject 1 ml of undiluted VELPAR L through the bark of
undesirable trees. Injections should be made at 4" intervals
around the circumference of the tree. When using tubular
injection equipment, inject near the ground level. When
using the “Hypo-Hatchet” Tree Injector or a similar devise,
inject at waist height. Treatment should be made in the
summer. Woody species controlled include black cherry,
oaks, and sweetgum.
SITE PREPARATION
- UNDILUTED APPLICATIONS
VELPAR L is recommended for control of brush in site
preparation.
GRID APPLICATION
Apply undiluted VELPAR L directly to the soil surface in a
grid pattern using an exact delivery handgun applicator.
This equipment delivers a thin stream of a predetermined
volume. VELPAR L should be applied during the period
from hardwood bud break to early summer.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
- SITE PREPARATION
USE RATES
The rates listed below are for broadcast application. Do not
use more than one application of VELPAR L per year.
Where burning is desired, burn the vegetation only after any
residual brush has completely defoliated, at least twice,
allowing for sufficient root uptake of VELPAR L
EASTERN US
VELPAR L
Following harvest, allow sufficient time for stumps and
injured trees to adequately resprout before applying
VELPAR L.
Soil Texture
(Qt/Acre)
Crop Species
Loblolly pine
Longleaf pine
Description
Loamy sand,
sandy loam
Established Trees
2–3
2–4
RELEASE - HARDWOOD SUPPRESSION
VELPAR L is recommended for conifer release where the
following species are grown:
Shortleaf pine Loam, silt loam,
Virginia pine
Slash pine
silt, sandy clay loam
Silty clay loam,
EASTERN US
clay loam, sandy clay,
silty clay, clay
4.5–6
Balsam fir
Red spruce
Black spruce
Loblolly pine
Longleaf pine
Norway spruce
Red pine
Shortleaf pine
Slash pine
Virginia pine
White spruce
Red pine
Loamy sand, sandy loam
2–4
4–6
6–8
Loam, silt loam, silt,
sandy clay loam
Silty clay loam, clay loam,
sandy clay, silty clay, clay
WESTERN US
Established Trees- 4 years of age from transplanting on
coarse-textured soils
Blue spruce
Douglas fir
Engleman spruce
Grand fir
Lodgepole pine
Noble fir
Ponderosa pine
Sitka spruce
White fir
- 3 years of age from transplanting on
medium-textured soils
- 2 years of age from transplanting for
Red Pine
Jeffrey pine
WESTERN US
APPLICATION TIMING
EASTERN US
Soil Texture
Description
VELPAR L
(Qt/Acre)
Crop Species
Apply VELPAR L from early spring to early summer after
hardwoods have broken bud and before full leaf expansion.
Blue spruce
Douglas fir
Loamy sand,
sandy loam
2-4.5
3.5-6
Applications made over the top of pines may result in
excessive pine injury under conditions of high humidity and
temperature (80 degrees F).
Englemen spruce Loam,
Grand fir
Jeffrey pine
silt loam,
sandy clay loam
WESTERN US
Lodgepole pine
Noble fir
Ponderosa pine
Sitka spruce
White fir
Silt, silty clay loam,
clay loam,
sandy clay, silty clay,
clay
Rainbelt (areas of high spring rainfall): For best results, apply
in late winter or spring when brush is actively growing, but prior
to conifer budbreak.. If application is made after bud break,
use directional spray equipment to prevent contact with
conifer foliage, as injury may result.
5-6
Snowbelt (areas of low spring rainfall): For best results, apply
in the fall before soil freezes and after the final resting bud has
hardened on the conifers. Or, spring applications may be made
after snow cover melts in anticipation of rainfall prior to conifer
budbreak. Brush control results from spring treatments will be
dependent on sufficient rainfall following application to activate
VELPAR L.
For first year plantings treat only transplant stock that is 2
years old (2-0, 1-1) or more, except (1-0) for Ponderosa and
Jeffrey pines. Apply VELPAR L only if rainfall has settled
the soil around the base and root systems of the transplants.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BRUSH SUPPRESSION
SINGLE STEM (BASAL SOIL)
Apply undiluted VELPAR L to the soil with an exact delivery
handgun applicator. Apply at the rate of 2–4 ml for each inch of
stem diameter at breast height. Direct the treatment to the soil
within 3 ft of the root collar of woody plants to be controlled.
When treating large stems and when more than one delivery of
VELPAR L is needed per stem, make application on opposite
sides of the stem.
Ash
Aspen
Balsam poplar
Birch
Box elder
Hawthorne
Hazel
Honeysuckle
Oaks
Red maple*
Snowbush ceanothus
Sumac*
Sweetgum*
Whitehorn
Willow
Brambles
Cherry (black, pin)
Deerbrush ceanothus
Dogwood*
Elm
For multi-stemmed and low-growing brush that have stem
diameters that are difficult to determine, apply VELPAR L at the
rate of 2–4 ml per 3ft of canopy width. For tall, slender
(columnar) brush types, apply 4–8 ml per 3ft of height. Base rate
on whichever canopy dimension is greater (width or height).
Greenleaf manzanita
When treating brush that requires more than a single 4 ml
application of VELPAR L, apply subsequent applications
equally spaced around the plant. If treating brush on sloped sites,
apply most of the VELPAR L on the uphill side of the stem. If
treating resprouts from brush disturbed by cutting or shredding,
the rate of application should be proportional to the original tree
size, not just the small regrowth of sprouts.
* Partial control
In addition to brush controlled, herbaceous species listed in
Weeds Controlled section of Release-Herbaceous Weed
Control may be controlled with these applications.
SPRAY EQUIPMENT
Apply VELPAR L by ground equipment or by air
(helicopter only).
INJECTION
No Worker Protection Standard worker entry restrictions or
worker notification requirements apply when this product is
directly injected into agricultural plants.
MIXING INSTRUCTIONS
For ground application, use enough water for thorough
coverage, usually a minimum of 25 gal per acre. For aerial
applications, use at least 5 gal of water per acre and at least
5 gal of water for every 1 gal of VELPAR L.
Inject 1 ml of undiluted VELPAR L through the bark of
undesirable trees. Injections should be made at 4" intervals
around the circumference of the tree. When using tubular
injection equipment, inject VELPAR L near the ground level.
When using the “Hypo-Hatchet” Tree Injector or a similar
devise, inject at waist height. Treatment should be made in the
summer. Woody species controlled include black cherry, oaks,
and sweetgum.
RELEASE - UNDILUTED APPLICATIONS
VELPAR L is recommended for hardwood suppression in
conifer release sites.
GRID APPLICATION
Apply undiluted VELPAR L directly to the soil surface in a grid
pattern using an exact delivery handgun applicator. This
equipment delivers a thin stream of a predetermined volume
when triggered. Apply VELPAR L during the period from
hardwood bud break to early summer.
IMPORTANT PRECAUTIONS
- RELEASE UNDILUTED
• Application of VELPAR L spots closer than 36" to conifer
seedlings in their first season or directly up slope from these
seedlings may result in injury or mortality.
Selection of the rate per acre and grid pattern depends on soil
texture and woody plant composition. Use the lower rates on
coarse textured soils and when the major component of the
hardwoods are susceptible species. Use the high rates on fine-
textured soils and hard-to-kill species.
• Use VELPAR L on seedlings in their first or fourth year and
older. Injury may result from use on two and three year old
seedlings where root growth is extensive but hardiness is
lacking.
Application Patterns and Rates For Undiluted VELPAR L
RELEASE- HERBACEOUS WEED CONTROL
VELPAR L is recommended for controlling herbaceous weeds
where the following species are grown:
ML/Spot
0.5
1.2
2.1
1.2
2.3
1.6
3.1
Grid (Ft)
3 X 4
3 X 6
4 X 6
3 X 3
3 X 6
3 X 3
3 X 6
Qt/Acre
2*
3
4
6
6
8
8
Coarse
EASTERN US
Medium/Fine
Loblolly pine
Longleaf pine
Red pine
Slash pine
WESTERN US
* Use on deep sands with pines four years or more of age.
Blue spruce
Douglas fir
Engleman spruce
Grand fir
Lodgepole pine
Noble fir
Ponderosa pine
Sitka spruce
White fir
Jeffrey pine
12
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATION TIMING
IMPORTANT PRECAUTIONS - FORESTRY
• Do not use VELPAR L in nurseries, seedbeds, or ornamental
plantings.
EASTERN US
Apply VELPAR L as a broadcast or banded spray in the spring
prior to conifer bud break to lessen conifer injury potential.
• On tracts of land where various soil types are present and
VELPAR L rate selection is difficult, conifer damage or less-
than-expected vegetation suppression may occur due to the
different rates required for various soil types.
WESTERN US
Rainbelt (areas of high spring rainfall): For best results, apply
as a broadcast or banded spray in the late winter or spring when
weeds are actively growing, but prior to conifer budbreak.. If
application is made after conifer bud break, use directional spray
equipment to prevent contact with conifer foliage, as injury may
result.
• Poor weed and brush control may result from the following:
–Heavy duff or slash present at time of application
–Use on poorly drained sites
–Applications made when the soil is saturated with water and
rain is imminent within 24 hours.
Snowbelt (areas of low spring rainfall): For best results, apply
as a broadcast or banded spray in the fall before soil freezes and
after the final resting bud has hardened on the conifers. Or,
spring applications may be made after snow cover melts in
anticipation of rainfall prior to conifer budbreak. Weed control
results from spring treatments will be dependent on sufficient
rainfall following application to activate VELPAR L.
–Applications to soils high in organic matter (greater
than 5%).
• Following harvest, allow stumps and injured trees sufficient
time to adequately resprout before applying VELPAR L.
• Where burning is desired, burn vegetation only after any
brush has completely defoliated, at least twice, allowing for
sufficient root uptake of VELPAR L
USE RATES
The rates listed below are for broadcast application. For band
application, use proportionately less. For example, use 1/2 of the
broadcast rates when treating a 3-ft band where row spacing is 6
ft.
• Do not use VELPAR L on frozen soils; use in spring after
snow melt.
• Do not add a surfactant in applications over the top of
conifers.
EASTERN US
• Weed control results from spring applications depend on
sufficient moisture to activate VELPAR L.
VELPAR L (Pt/Acre)
Soil Texture
Description
First Year
Plantings
4
Established
• When applying VELPAR L after transplanting, wait until
rainfall has settled the soil around the base and root systems
of the transplants before making the treatment.
Trees
Loamy sand,
sandy loam(50-85% sand)
4–5
• Crop injury may occur when VELPAR L is used:
–On trees that show poor vigor, insect damage, disease,
winter injury, or other stress conditions
Loam, silt loam, silt,
sandy clay loam
4–5
5–6
5–7
7–8
–On any soil containing less than 1% organic matter
Silty clay loam,
clay loam, sandy clay,
silty clay, clay
–On loamy sand or sandy loam with less than 2% organic
matter, except Jeffrey pine and Ponderosa pine
–On conifer foliage after conifer bud break.
Red pine only - Refer to recommended rates in the
HARDWOOD SUPPRESSION - Eastern US table on page 11.
WESTERN US
–On gravelly or rocky soils, exposed subsoils, clay knobs,
sand, or sandy soil with 85% or more sand.
–On crop species not listed on this label
Refer to recommended rates in the HARDWOOD
SUPPRESSION-Western US table on page 11.
• Do not cut treated vegetation for forage or hay nor graze
domestic animals on treated areas for 60 days following
application.
WEEDS CONTROLLED
Annual bluegrass
Aster
Fireweed (willowweed)*
Fleabane
Barnyardgrass
Bentgrass
Bracken Fern
Bromegrass
Catsear (false dandelion)
Common groundsel
Common ragweed
Crabgrass*
Curly dock*
Dandelion*
Foxtail
Goldenrod*
Heath aster*
Horseweed*
Orchardgrass*
Oxeye daisy
Panicums
Pennsylvania smartweed
Ryegrass*
Squawcarpet
Velvetgrass
Dogfennel
Fescue*
Wild carrot*
* Partial control
13
Download from Www.Somanuals.com. All Manuals Search And Download.
3–4 Gal/Acre
NON-AGRICULTURAL USES
Bahiagrass*
Bermudagrass*
Blackberry
Bluegrass
Broomsedge
Camphorweed
Canada thistle*
Chickweed
Clovers
Dewberry
Dogfennel*
Fescue*
Fingergrass
Foxtail
Guineagrass
Heath aster
Honeysuckle
Lantana
Marestail
Natalgrass
Plantain
Prickly lettuce
Ragweed
Smutgrass†
Spanish needle
Vaseygrass
Wild carrot
NON-AGRICULTURAL USE REQUIREMENTS
The requirements in this box apply to uses of this
product that are NOT within the scope of the Worker
Protection Standard for agricultural pesticides (40 CFR
Part 170). The WPS applies when this product is used to
produce agricultural plants on farms, forests, nurseries,
or greenhouses.
Industrial and Pasture/Rangeland weed and brush
control applications as described on this label for
DuPont VELPAR L are not within the scope of the
Worker Protection Standard.
The area being treated must be vacated by unprotected
persons.
Do not enter or allow entry into treated areas until sprays
have dried to perform hand tasks.
* Partial control
† Partial control may result with some of the giant (larger) smutgrass species.
SPECIFIC WEED PROBLEMS
APPLICATION INFORMATION
Control of Canada Thistle in Crown Vetch - VELPAR L is
recommended for control of Canada thistle in established stands
of crown vetch on noncrop sites. Make a single application of
3–5 pt of VELPAR L from late spring through mid-summer,
when thistle is actively growing prior to flowering. Do not use a
surfactant. Some discoloration of the crown vetch foliage may
occur after application.
VELPAR L is recommended for general weed and brush control
in noncrop sites such as railroads, highways, utility and pipeline
rights-of-way, petroleum tank farms, storage areas, industrial
plant sites, and other similar areas.
NONCROP, INDUSTRIAL SITES
SPRAY EQUIPMENT
Apply VELPAR L uniformly over the desired area using ground
equipment only.
VELPAR L is recommended for control of many annual,
biennial, and perennial weeds in noncrop, industrial sites.
APPLICATION TIMING
Apply VELPAR L as a preemergence or postemergence spray
when weeds are actively germinating or growing.
MIXING INSTRUCTIONS
For ground application, use enough water for thorough
coverage, usually a minimum of 25 gal per acre. Higher
application volumes may be needed to obtain uniform
application with handgun equipment.
WEEDS CONTROLLED - USE RATE
VELPAR L effectively controls the following weeds when
applied at the use rates shown. When applied at lower rates,
VELPAR L provides short-term control of the weeds listed;
when applied at higher rates, weed control is increased and
extended.
INDUSTRIAL TURF (UNIMPROVED ONLY)
VELPAR L is recommended for selective weed control in
established stands of bermudagrass and/or bahiagrass in noncrop
areas.
1–2 1/2 Gal/Acre
APPLICATION TIMING
Make a single application of VELPAR L per year when weeds
are actively growing.
Barnyardgrass
Bindweed*
Bouncingbet*
Bromegrass
Buffalograss*
Burdock
Lespedeza
Milkweed*
Mustard
Nutsedge*
Orchardgrass*
Oxalis
Paragrass
Pigweed
Purslane
Quackgrass
Ryegrass, annual
Smartweed
Spurge
Star thistle
Trumpetcreeper*
Wild oats*
Wild parsnip
WEEDS CONTROLLED - USE RATE
VELPAR L effectively controls the following weeds at the rates
shown. Use a lower rate on coarse-textured soils (sand to sandy
loam). Use the higher rate on fine-textured soils (clay loam to
clay) and on soils high in organic matter.
Cocklebur
Crabgrass
Crown vetch
Curly dock*
Dandelion*
Dogbane*
Fiddleneck
Filaree
Fleabane
Goatsbeard vine
Goldenrod
2 3/4–4 1/2 pt
Barnyardgrass
Dogfennel
Fescue
Lespedeza
Little barley
Maypop (passion flower)
Oxalis
Pepperweed
Pigweed
Smutgrass†
† Partial control may result with some of the giant (larger) smutgrass species.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPRAY EQUIPMENT
SPRAY EQUIPMENT
AND APPLICATION TECHNIQUES
Apply VELPAR L uniformly over the desired area using ground
equipment only.
BROADCAST
MIXING INSTRUCTIONS
Apply 2–4 gal of VELPAR L per acre as a coarse spray using
ground equipment only. Use enough water for thorough
coverage, usually a minimum of 25 gal per acre.
For ground application, use enough water for thorough coverage
usually a minimum of 25 gal per acre. The use of a surfactant is
not recommended.
BASAL (SOIL)
IMPORTANT PRECAUTIONS
- INDUSTRIAL UNIMPROVED TURF
• Use VELPAR L only in stands of bermudagrass and
bahiagrass established for at least one year. Do not treat newly
sprigged or sodded areas.
Undiluted - Apply VELPAR L undiluted with an exact-
delivery handgun applicator. This equipment delivers a thin
stream of a predetermined volume when triggered. Apply
VELPAR L at the rate of 2–4 ml for each inch of stem
diameter at breast height. Do not exceed 4 gal of VELPAR L
per acre per year. Direct the treatment to the soil within 3 ft of
the root collar of woody plants to be controlled. When treating
large stems and when more than one delivery of VELPAR L is
needed per stem, make applications on opposite sides of the
stem.
• Some discoloration of the bermudagrass or bahiagrass may
occur after application.
• Injury may result when desirable grasses are under stress from
drought, insects, disease, cold temperature, or poor fertility.
• Severe turf injury may occur if applications are made on
gravelly or rocky soils, thinly covered subsoils, or soils with
less than 1% organic matter.
For multi-stemmed and low-growing brush that have stem
diameters that are difficult to determine, apply VELPAR L at
the rate of 2–4 ml per 3" of canopy width. For tall, slender
(columnar) brush types, apply 4–8 ml per 3" of height. Base
the rate on whichever canopy dimension is greater (width or
height).
BRUSH CONTROL
VELPAR L is recommended for the control of undesirable
woody plants in noncrop sites.
APPLICATION TIMING
Apply VELPAR L from late winter through summer, prebud
break until new growth hardens off.
When treating brush that requires more than a single 4 ml
application of VELPAR L, apply subsequent applications
equally spaced around the plant. If treating brush on sloped
sites, apply most of the VELPAR L on the uphill side of the
stem. If treating resprouts from brush disturbed by cutting or
shredding, the rate of application should be proportional to the
original tree size, not just the small regrowth of sprouts.
In areas where the soil remains frozen during the winter and
spring rains are usually inadequate for soil activation, a fall
or winter treatment may be applied before the soil freezes.
WOODY PLANTS CONTROLLED - USE RATE
2–4 Gal/Acre
Diluted - Mix one gal of VELPAR L with 5 or more gal of
water. Apply 2–4 gal of VELPAR L per acre. Direct the spray
to the soil in a serpentine pattern so that the swath on the soil
is 6–12" wide at the base of the brush. Swaths should be 2–4
ft apart.
Alder
American elm
Ash
Manzanita
Mesquite
Mulberry
Aspen
Balsam poplar
Birch
Multiflora rose
Myrtle
Oaks
IMPORTANT PRECAUTIONS - NONCROP
• Injury to or loss of desirable trees or other plants may result if
VELPAR L is applied or if equipment is drained or flushed on
or near desirable trees or other plants, on areas where their
roots may extend, or in locations where the chemical may be
washed or moved into contact with their roots.
Black cherry
Blackgum
Catclaw acacia
Chinaberry*
Chinese elm
Chinese tallow
Deerbrush
Dogwood
Eastern red cedar*
Hackberry
Hawthorne
Hazel
Osage orange
Persimmon
Privet
Red maple
Sassafras*
Small soapweed
Snowbrush
Sourwood
Sumac
Sweet bay
Sweet gum
Whitebrush
Whitehorn
Wild plum
Willow
• Prevent spray from drifting to desirable plants.
• Poor weed and brush control may result from the following:
–Use on poorly drained sites
–Applications made when the soil is saturated with water and
rain is imminent within 24 hours.
–Applications to soils high in organic matter (greater
than 5%).
Hickory
Huisache
Juniper
• Following mechanical cutting or clearing, allow stumps and
injured trees sufficient time to adequately resprout before
applying VELPAR L.
Locust
Lotebush
Yellow Poplar
• Do not use VELPAR L on frozen soils.
• Do not use VELPAR L on lawns, driveways, tennis courts, or
other residential or recreational areas.
*Partial control
15
Download from Www.Somanuals.com. All Manuals Search And Download.
• Weed and brush control results from spring applications
depend on sufficient moisture to activate VELPAR L.
roots may extend, or in locations where the chemical may be
washed or moved into contact with their roots.
• Do not cut treated vegetation for forage or hay nor graze
domestic animals on treated areas for 60 days following
application. For rates above 3 gal per acre, do not cut treated
vegetation for forage or hay nor graze domestic animals for
1 year.
• Severe crop injury may occur if applications are made on
gravelly or rocky soils, thinly covered subsoils, or soils with
less than 1% organic matter.
BRUSH CONTROL
PASTURE/RANGELAND
PASTURE
VELPAR L is recommended for the control of undesirable
woody plants in pasture or rangeland.
VELPAR L is recommended for control of brush and weeds in
pasture.
APPLICATION TIMING
BERMUDAGRASS/BAHIAGRASS PASTURES
Apply VELPAR L from late winter through summer, pre-
budbreak until new growth hardens off.
VELPAR L is recommended for control of smutgrass and other
weeds in established stands of bermudagrass and bahiagrass.
In areas where the soil remains frozen during the winter and
spring rains are usually inadequate for soil activation, a fall
or winter treatment may be applied before the soil freezes.
APPLICATION TIMING
Make a single application of VELPAR L per year when weeds
are actively growing.
WOODY PLANTS CONTROLLED
WEEDS CONTROLLED - USE RATES
Alder
American elm
Ash
Aspen
Balsam poplar
Birch
Black cherry
Blackgum
Catclaw acacia
Chinaberry*
Chinese elm
Chinese tallow
Deerbrush
Dogwood
Eastern red cedar*
Hackberry
Hawthorne
Hazel
Lotebush
Manzanita
Mesquite
VELPAR L effectively controls the following weeds at the rates
shown. Use a lower rate on coarse-textured soils (sand to sandy
loam). Use the higher rate on fine-textured soils (clay loam to
clay) and on soils high in organic matter.
Mulberry
Multiflora rose
Myrtle Oaks
Osage orange
Persimmon
Privet
Red maple
Sassafras*
Small soapweed
Snowbrush
Sourwood
Sumac
Sweet bay
Sweet gum
Whitebrush
Whitehorn
Wild plum
Willow
2 3/4–4 1/2 pt
Barnyardgrass
Dogfennel
Fescue
Lespedeza
Little barley
Maypop (passion flower)
Oxalis
Pepperweed
Pigweed
Smutgrass*
* Partial control may result with some of the giant (larger)
smutgrass species.
SPRAY EQUIPMENT
Apply VELPAR L uniformly over the desired area using ground
equipment only.
Hickory
Huisache
Juniper
Locust
MIXING INSTRUCTIONS
For ground application, use enough water for thorough coverage
usually a minimum of 25 gal per acre. The use of a surfactant is
not recommended.
Yellow poplar
*
Partial control.
IMPORTANT PRECAUTIONS - PASTURE
SPRAY EQUIPMENT
AND APPLICATION TECHNIQUES
• Use VELPAR L only in stands of bermudagrass and
bahiagrass established for at least one year. Do not treat newly
sprigged or sodded areas.
Basal (Soil) Undiluted - Apply VELPAR L undiluted with an
exact-delivery handgun applicator. This equipment delivers a
thin stream of a predetermined volume when triggered. Apply
VELPAR L at the rate of 2–4 ml for each inch of stem
diameter at breast height. Do not exceed 1/3 gal of VELPAR L
per acre per year. Direct the treatment to the soil within 3” of
the root collar of woody plants to be controlled. When treating
large stems and when more than one delivery of VELPAR L is
needed per stem, make applications on opposite sides of the
stem.
• Some temporary discoloration of the bermudagrass or
bahiagrass may occur after application.
• Treatment of mixed pastures containing forage species other
than bermudagrass or bahiagrass may result in injury or
mortality to the other forage species.
• Injury may result when desirable grasses are under stress from
drought, insects, disease, cold temperature, or poor fertility.
• Injury to or loss of desirable trees or other plants may result if
VELPAR L is applied or if equipment is drained or flushed
on or near desirable trees or other plants, on areas where their
16
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT PRECAUTIONS
- PASTURE /RANGELAND
• Injury to or loss of desirable trees or other plants may result if
VELPAR L is applied or if equipment is drained or flushed on
or near desirable trees or other plants, on areas where their
roots may extend, or in locations where the chemical may be
washed or moved into contact with their roots.
CONTROLLING DROPLET SIZE - AIRCRAFT
• Number of Nozzles - Use the minimum number of nozzles
with the highest flow rate that provide uniform coverage.
• Nozzle Orientation - Orienting nozzles so that the spray is
emitted backwards, parallel to the airstream will produce
larger droplets than other orientations.
• Nozzle Type - Solid stream nozzles (such as disc and core
with swirl plate removed) oriented straight back produce
larger droplets than other nozzle types.
• Poor weed and brush control may result from the following:
–Use on poorly drained sites
BOOM LENGTH AND HEIGHT
–Applications made when the soil is saturated with water and
rain is imminent within 24 hours
• Boom Length (aircraft) - The boom length should not
exceed 3/4 of the wing length, using shorter booms decreases
drift potential. For helicopters use a boom length and position
that prevents droplets from entering the rotor vortices.
–Applications to soils high in organic matter (greater
than 5%)
• Following mechanical cutting or clearing, allow stumps and
injured trees sufficient time to adequately resprout before
applying VELPAR L.
• Boom Height (aircraft) - Application more than 10 ft above
the canopy increases the potential for spray drift.
• Do not use VELPAR L on frozen soils.
• Boom Height (ground) Setting the boom at the lowest
labeled height (if specified) which provides uniform coverage
reduces the exposure of droplets to evaporation and wind.
The boom should remain level with the crop and have
minimal bounce.
• Weed and brush control results depend on sufficient moisture
to activate VELPAR L.
• When VELPAR L is applied as a basal soil treatment, there is
no restriction on grazing by domestic animals nor on cutting
surrounding vegetation for forage or hay.
WIND
• For broadcast pasture applications of VELPAR L, do not cut
treated vegetation for forage or hay nor graze domestic
animals on treated areas for 60 days.
Drift potential increases at wind speeds of less than 3 mph
(due to variable direction and inversion potential) or more
than 10 mph. However, many factors, including droplet size
and equipment type determine drift potential at any given
wind speed. AVOID GUSTY OR WINDLESS
CONDITIONS.
SPRAY DRIFT MANAGEMENT
The interaction of many equipment- and weather-related factors
determines the potential for spray drift. The applicator is
responsible for considering all these factors when making
application decisions. Avoiding spray drift is the responsibility
of the applicator.
Note: Local terrain can influence wind patterns. Every
applicator should be familiar with local wind patterns and
how they effect spray drift.
IMPORTANCE OF DROPLET SIZE
TEMPERATURE AND HUMIDITY
The most effective way to reduce drift potential is to apply large
droplets (greater than 150–200 microns). The best drift
management strategy is to apply the largest droplets that provide
sufficient coverage and control. The presence of sensitive
species nearby, the environmental conditions, and pest pressure
may affect how an applicator balances drift control and
coverage. Applying larger droplets reduces drift potential, but
will not prevent drift if applications are made improperly or
under unfavorable environmental conditions! See the Wind,
Temperature and Humidity, and Temperature Inversions sections
below.
When making applications in hot and dry conditions, set up
equipment to produce larger droplets to reduce effects of
evaporation.
SURFACE TEMPERATURE INVERSIONS
Drift potential is high during a surface temperature inversion.
Surface inversions restrict vertical air mixing, which causes
small suspended droplets to remain close to the ground and
move laterally in a concentrated cloud. Surface inversions are
characterized by increasing temperature with altitude and are
common on nights with limited cloud cover and light to no
wind. They begin to form as the sun sets and often continue
into the morning. Their presence can be indicated by ground
fog; however, if fog is not present, inversions can also be
identified by the movement of smoke from a ground source or
an aircraft smoke generator. Smoke that layers and moves
laterally in a concentrated cloud (under low wind conditions)
indicates a surface inversion, while smoke that moves upward
and rapidly dissipates indicates good vertical air mixing.
CONTROLLING DROPLET SIZE
- GENERAL TECHNIQUES
• Volume - Use high flow rate nozzles to apply the highest
practical spray volume. Nozzles with higher rated flows
produce larger droplets.
• Pressure - Use the lower spray pressures recommended for the
nozzle. Higher pressure reduces droplet size and does not
improve canopy penetration. When higher flow rates are
needed, use a higher-capacity nozzle instead of increasing
pressure.
SHIELDED SPRAYERS
• Nozzle Type - Use a nozzle type that is designed for the
intended application. With most nozzle types, narrower spray
angles produce larger droplets. Consider using low-drift
nozzles.
Shielding the boom or individual nozzles can reduce the
effects of wind. However, it is the responsibility of the
applicator to verify that the shields are preventing drift, and
not interfering with uniform deposition of the product.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
SPRAY TANK CLEANOUT
LIMITATION OF
Thoroughly clean all traces of VELPAR L from application
equipment immediately after use. Flush the tank, pump,
hoses, and boom with several changes of water after
removing nozzle tips and screens (clean these parts
separately).
WARRANTY AND LIABILITY
NOTICE: Read This Limitation of Warranty and Liability
Before Buying or Using This Product. If the Terms Are
Not Acceptable, Return the Product at Once, Unopened,
and the Purchase Price Will Be Refunded.
It is impossible to eliminate all risks associated with the use
of this product. Such risks arise from weather conditions,
soil factors, off target movement, unconventional farming
techniques, presence of other materials, the manner of use
or application, or other unknown factors, all of which are
beyond the control of DuPont. These risks can cause:
ineffectiveness of the product; crop injury, or; injury to
non-target crops or plants.
STORAGE AND DISPOSAL
STORAGE: Do not subject to temperatures below
32 °F. Store product in original container only. Do not
contaminate water, other pesticides, fertilizer, food, or
feed in storage.
PRODUCT DISPOSAL: Do not contaminate water,
food, or feed by storage or disposal. Pesticide wastes
are acutely hazardous. Improper disposal of excess
pesticide, spray mixture, or rinsate is a violation of
federal law. If these wastes cannot be disposed of by
use according to label instructions, contact your State
Pesticide or Environmental Control Agency, or the
Hazardous Waste representative at the nearest EPA
regional office for guidance.
DuPont does not agree to be an insurer of these risks.
WHEN YOU BUY OR USE THIS PRODUCT, YOU
AGREE TO ACCEPT THESE RISKS.
DuPont warrants that this product conforms to the chemical
description on the label thereof and is reasonably fit for the
purpose stated in the Directions for Use, subject to the
inherent risks described above, when used in accordance
with the Directions for Use under normal conditions.
CONTAINER DISPOSAL: Triple rinse (or
equivalent) the container. Then offer the container for
recycling or reconditioning; or puncture and dispose of
the container either in a sanitary landfill, by
incineration, or, if allowed by state and local
authorities, by burning. If the container is burned, stay
out of the smoke.
DUPONT MAKES NO OTHER EXPRESS OR IMPLIED
WARRANTY OF FITNESS OR OF
MERCHANTABILITY OR ANY OTHER EXPRESS OR
IMPLIED WARRANTY.
IN NO EVENT SHALL DUPONT OR SELLER BE
LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL
OR SPECIAL DAMAGES RESULTING FROM THE USE
OR HANDLING OF THIS PRODUCT. BUYER'S OR
USER'S BARGAINED-FOR EXPECTATION IS CROP
PROTECTION. THE EXCLUSIVE REMEDY OF THE
USER OR BUYER AND THE EXCLUSIVE LIABILITY
OF DUPONT OR SELLER, FOR ANY AND ALL
CLAIMS, LOSSES, INJURIES OR DAMAGES
NOTICE TO BUYER: Purchase of this material does not
confer any rights under patents of countries outside of the
United States.
(INCLUDING CLAIMS BASED ON BREACH OF
WARRANTY OR CONTRACT, NEGLIGENCE, TORT
OR STRICT LIABILITY), WHETHER FROM FAILURE
TO PERFORM OR INJURY TO CROPS OR OTHER
PLANTS, AND RESULTING FROM THE USE OR
HANDLING OF THIS PRODUCT, SHALL BE THE
RETURN OF THE PURCHASE PRICE OF THE
PRODUCT, OR AT THE ELECTION OF DUPONT OR
SELLER, THE REPLACEMENT OF THE PRODUCT.
DuPont or its Ag Retailer must have prompt notice of any
claim so that an immediate inspection of buyer's or user's
growing crops can be made. Buyer and all users shall
promptly notify DuPont or a DuPont Ag Retailer of any
claims, whether based on contract, negligence, strict
liability, other tort or otherwise or be barred from any
remedy.
This Limitation of Warranty and Liability may not be
amended by any oral or written agreement.
1 Registered Trademark of DowElanco
SL - 547-2 9038 3/31/97
For product information call 1-888-6-DUPONT
© 1998 E. I. du Pont de Nemours and Company, Agricultural Products, Wilmington, Delaware 19898
18
Download from Www.Somanuals.com. All Manuals Search And Download.
|