2000 Operator's Manual
4500
SERIES
Download from Www.Somanuals.com. All Manuals Search And Download.
INDEX
SAFETY ............................................................Pages 2 - 7
WARRANTY POLICY ......................................Page
SPECIFICATIONS ...........................................Page
SEAT ADJUSTMENT ......................................Page
8
9
10
CONTROLS .....................................................Pages 11 - 14
OPERATION INSTRUCTIONS......................Pages 15 - 20
CAREAND MAINTENANCE .........................Pages 21 - 30
STANDARD PARTS LIST ................................Page
31
TROUBLESHOOTING ...................................Pages 32 - 34
4500 Series
Part No. 1857-0599
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
RIDING LAWNMOWERS, IF IMPROPERLY OPERATED,
CAN CAUSE SERIOUS INJURY OR DEATH
The most common causes of injury to the operator or bystander...
BLADECONTACT
TIP-OVER
BACK-OVER
RUN-OVER
...read and understand this manual to prevent injuries.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SAFETY SYMBOLS
Safety Alert Symbol
When you see this symbol,
BE ALERT to the potential for injury.
Follow recommended safety precautions and safe operating practices.
Danger
indicates an imminently hazardous situation
which, if not avoided, will result in death or
serious injury.
Warning
indicates a potentially hazardous situation
which, if not avoided, could result in death
or serious injury.
Caution
indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury. It may also be used to alert
against unsafe practices.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
Thiscuttingmoweriscapableofamputatinghands&feet,
andthrowingobjects.
Failuretoobservethefollowingsafetyinstructionscouldresultin
seriousinjuryordeath.
GENERAL OPERATION:
•
•
•
•
•
•
•
Read, understand, and follow all instructions in the manual and on the mower before starting.
Only allow responsible adults, who are familiar with the instructions, to operate the mower.
Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade.
Be sure the area is clear of other people before mowing. Stop mower if anyone enters the area.
Never carry passengers.
Do not mow in reverse unless absolutely necessary. Always look down and behind before and while backing.
Be aware of the mower discharge direction and do not point it at anyone. Do not operate the mower without either
the entire grass catcher or the deflector in place.
•
•
Slow down before turning.
Never leave a running mower unattended. Always turn off blades, set parking brake, stop engine, and remove key
before dismounting.
•
•
•
•
•
•
Turn off blades when not mowing.
Stop engine before removing grass catcher or unclogging chute.
Mow only in daylight or good artificial light.
Do not operate the mower while under the influence of alcohol or drugs.
Watch for traffic when operating near or crossing roadways.
Use extra care when loading or unloading the mower into a trailer or truck.
Do not ride the mower when loading & unloading.
•
•
Always wear safety goggles or safty glasses with side shields when operating mower.
Data indicates that operators, age 60 years and above, are involved in a large percentage of riding mower-related
injuries. These operators should evaluate their ability to operate the riding mower safely enough to protect
themselves and others from serious injury.
•
Follow the manufacturer's recommendation for wheel weights or counterweights.
The Engine Exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive harm.
WARNING:
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SLOPE OPERATION:
Slopes are a major factor related to loss-of-control and tip-over accidents,
which can result in severe injury or death.
All slopes require extra caution.
If you cannot back up the slope or if you feel uneasy on it, do not mow it.
DO
Mow across the slope with your Dixon ZTR - never up or down.
Remove obstacles such as rocks, tree limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain could overturn the mower. Tall grass can hide obstacles.
Use slow speed. Tires may lose traction on slopes even though the brakes are functioning properly.
Use extra care with grass catchers or other attachments. These can change the stability of the mower.
Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction.
Avoid starting or stopping on a slope. If tires lose traction, disengage the blades and proceed slowly down the
slope.
If front wheels lift off the ground, pull the levers back to stabilize the mower.
DO NOT
Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible.
Do not mow near drop-offs, ditches, or embankments. The mower could suddenly turn over if a wheel is over
the edge of a cliff or ditch, or if an edge caves in.
Do not mow on wet grass. Reduced traction could cause sliding.
Do not try to stabilize the mower by putting your foot on the ground.
Do not use grass catcher on steep slopes.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
CHILDREN:
Tragic accidents can occur if the operator is not alert to the
presence of children.
Children are attracted to lawn mowers and the mowing activity.
NEVER assume children will stay where they were last seen.
Be alert to avoid accidents.
• Keep children out of the mowing area and under the watchful care of another
responsible adult.
• Be alert and turn mower off if a child enters the area.
• Before and during backing, look behind and DOWN for small children.
• Never carry children. They may fall off and be seriously injured or interfere with safe
moweroperation.
• Never allow children to operate the mower.
• Use extra care when approaching blind corners, shrubs, trees, or other objects that
may obscure vision.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
SERVICE:
•
Useextracarein handlinggasolineandotherfuels. Theyareflammableandvaporsareexplosive.
Use only an approved container.
Never remove gas cap or add fuel with the engine running. Allow engine to cool before refueling. Do not
smoke.
Never refuel the mower indoors.
Never store the mower or fuel container inside a building where there is an open flame.
Never fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers
on the ground away from your vehicle before filling.
When practical, remove gas-powered equipment from the truck or trailer and refuel it on the ground. If this
is not possible, then refuel such equipment on a trailer with a portable container, rather than from a gasoline
dispenser nozzle.
If a gasoline dispenser nozzle must be used, keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do not use a nozzle lock-open device.
•
•
•
•
Never run a mower inside a closed area. The exhaust fumes are toxic.
Keep nuts and bolts tight, especially blade attachment bolts, and keep equipment in good condition.
Never tamper with safety devices. Check their proper operation regularly.
Keep mower free of grass, leaves, or other debris buildup. Clean up oil or fuel spillage. Allow mower to cool
before storing.
•
•
•
Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.
Never make adjustments or repairs with the engine running.
Grass catcher components are subject to wear, damage, and deterioration, which could expose moving parts or
allow objects to be thrown. Frequently check components and replace with original equipment parts, when
necessary.
•
•
Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing
them.
Batteries contain sulfuric acid. To prevent burns avoid contact with skin, eyes and clothing. To prevent a fire or
explosion keep sparks and open flames away from battery.
Before disconnecting the negative (-) ground cable, make sure all switches are OFF.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
DIXON LIMITED WARRANTY POLICY -- ZTR Model 4500
This warranty policy applies to all Model 4500 mowers purchased on or after September 1, 1997.
WARRANTY:
Commercial Applications: Dixon ZTR Models 4500 used in any commercial application are warranted for a period of
ninety (90) days from date of purchase. Commercial applications or use is defined as any use other than at the owners
primary place of residence. Home Owner Applications: Dixon ZTR Models 4500 used primarily at the owners place of
residence are warranted for a period of two (2) years from date of purchase. DIXON ZTR MOWERS ARE WAR-
RANTED AGAINST DEFECTS IN MATERIALS AND WORKMANSHIP AND PROVIDES FOR REPLACE-
MENT OR REPAIR OF PARTS INCLUDING LABOR COSTS. THE WARRANTY IS SUBJECT TO THE
FOLLOWING CONDITIONS AND LIMITATIONS:
1. Warranty applies only to original retail purchaser of new and unused mowers and accessories.
2. All Dixon warranty must be accomplished by authorized Dixon dealers and in accordance with Dixon warranty
policy allowances. All warranty claims must be approved by Dixon Industries, Inc.
3. Battery warranty: Limited to 90 days date of purchase.
4. Accessories Warranty (Grass Catchers, Snow Blades, Tine Rakes, Covers, etc.): Limited to 90 days date of purchase.
5. Warranty does not apply to damage in transit or incidents of misuse, negligence, accidents, or alteration.
The use of parts or components other than those supplied by Dixon Industries, Inc. VOIDS ALL WARRANTY.
6. The following items are not covered by this warranty policy:
(a) Pick up and delivery charges for transportation of mower to and from an Authorized Dixon Dealer’s
place of business.
(b) Routine maintenance or adjustments.
(c) Belts/cutting blades/Hydro-Gear Filters.
(d) Engines -- All engines used on Dixon ZTR mowers are warranted by each individual engine manufacturer.
(e) Any costs or expense of providing substitute equipment while repair work is being performed on a warranted
mower.
7. There is no other express warranty. Implied warranties, including those of merchantability and fitness for a
particular purpose, are limited to the same duration of the express warranty, and to the extent permitted by law, any
and all implied warranties are excluded. Liabilities for consequential damages under any and all warranties are
WARRANTYVALIDATION: At the time of sale, selling dealer must review each portion of this warranty document,
complete the information section below, secure customer’s signature and send copy to Dixon Industries, Inc.
DATE OF PURCHASE
MODEL
SN
DM-
(Owner’s Name)
(Address)
(Dealership)
(Address)
(Owner’s Signature)
(Dealer’s Signature)
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Models ZTR 4515B and 4516K
CHASSIS:
BODY:
Twin 12 gauge side frames and 7 gauge transmission and engine base plate.
All body parts are made of high density polyethylene. Dent and corrosion resistant.
Front body contains access panel for battery service.
MOWERDECKS:
42" Deck: 13 GA Stamped Steel Construction - 42" Cut Width
50" Deck 11 GA Fabricated Construction/Reinforcement Ribs - 50" Cut Width
Cut height approximately 1" to 4" via 7 position lift handle.
Electricclutch.
BLADEDRIVE:
TRANSMISSION:
ENGINE:
Each rear wheel is independently driven by a HydroGear IZT hydrostatic drive.
Model 4515B:
15.5 HP Vanguard Briggs & Stratton, 4-Cycle, Single Cylinder, Overhead Valve,
Air-Cooled, Gasoline, Vertical Shaft With Cast Iron Cylinder Sleeve, Oil Pump
With Integral Oil Filter.
Model 4516K:
16 HP Kohler Command 16, 4-Cycle, Single Cylinder, Overhead Valve, Air-
Cooled, Gasoline, Pressure Lubricated, With Oil Filter, Vertical Shaft, Aluminum
Head and Block with Cast-Iron Cylinder Liner. Smart Spark Ignition.
STARTINGSYSTEM:
TIRES:
Electric by key switch operation with safety interlock blade drive.
Front
Rear
11 X 4.00 X 5 ribbed tread.
18 X 8.50 X 8 Multi-Trac
RECOMMENDED
TIREPRESSURE:
Front
Rear
16-21 lbs.
8-14 lbs.
CAPACITIES:
Fuel
2.7 gallons total.
Engine
Briggs & Stratton - 1.50 quarts oil.
Kohler - 2 quarts oil with filter.
DIMENSIONS:
Width
Height
Length
Weight
44" Maximum Track Width
42" to top edge of seat.
72" hitch tab to front bumper.
Power Unit:
463 lbs.
w/42" Deck:
547 lbs.
w/50" Deck: 603 lbs.
NOTE:
Additionalinformationprovidedinserviceinstructionsundertheindividualcomponent.
SPECIFICATIONSSUBJECT TO CHANGEWITHOUT NOTICE
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SEAT ADJUSTMENT
INSTRUCTIONS
Place parking brake in ON position. (Pull brake lever up)
Raise and push seat assembly forward.
1.
2.
3.
Loosen five nuts, P/N 3205, and slide seat forward or backward to desired position.
Retighten nuts, P/N 3205.
DO NOT operate mower without seat adjustments properly tightened.
4
Raise and push seat assembly and upper body rearward to closed position.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
PARKING BRAKE:
The parking brake is designed to hold the mower from
moving and is not intended for use in stopping the mower
while it is in motion. The engine will stop if the parking
brake is engaged while the control levers are in the drive
position.
CAUTION
Engage parking brake before
starting engine.
TO SET PARKING BRAKE:
The hand operated parking brake is located on the right
fender.
To engage brake, pull lever up(to the rear).
To release brake, move lever forward (down).
NOTE: Always set parking brake before dismounting.
Release parking brake before moving mower.
TRANSMISSION DRIVE SYSTEM:
Allows the mower to turn on its own axis
"Zero Turning Radius"
Each lever controls one side of the mower.
NOTE: Thepressurerequiredtooperatethemowerisvery
light.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
(left turn opposite)
TO GO FORWARD:
From neutral position, gently push both drive levers forward.
To increase speed, move levers farther forward.
TO GO BACKWARD:
From neutral position, gently pull both drive levers toward you.
TURNING:
Turning is controlled by moving one drive lever slightly forward or rearward of the other.
To turn left, move left lever rearward of the right lever.
To turn "square corners" move lever of desired direction to neutral.
To turn on mower's own axis (zero turning radius) stop and move one lever to reverse
position and the other to forward position.
BRAKING:
To brake mower, move both levers in direction opposite of travel, release levers to neutral,
set parking brake. Park only on level surfaces.
THROTTLE CONTROL:
Located on control panel to operator's right.
Throttle control for engine speed.
Choke for engine starting.
ThrottleControlshould beset totheMAXIMUM or wideopen settingtoinsureadequate
cooling of the engine and to maintain mower deck blade speed while mowing.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTROLS
BLADE DRIVE:
Located on control panel, on operator's right.
To engage the mower blades, pull up on the
switch.
To disengage blades, push down.
CIRCUIT BREAKER:
Protection of the electrical system is by
(1) 15 amp circuit breaker.
If circuit breaker trips, push button to reset.
If this condition repeats, consult dealer
for inspection and repair.
MOWER DECK CUT HEIGHT LIFT LEVER:
Located to the left of operator.
Controls the cutting height.
Seven positions of adjustment.
Move lever in and forward to lower.
Move lever in and back to raise.
NOTE: Always use high for transport.
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
Safeand successfuloperation willdepend upon theoperator havingthecorrect knowledgeofallcontrolsused
on the mower and making good judgements about the terrain to be mowed.
NEVER allowanyoneto operatethemower without completeknowledgeofallcontrolsand their
functions.
Duringinitialoperation, "learningtodrive", set throttleat slowspeed.
Sound judgement bytheoperator willprevent accidents.
Drink/Cup Holder located on the left rear fender is for transport or carrying only!
Mower usage requires that both hands be free to control individual levers.
DO NOT ATTEMPT operation of mower with any type
of container or other object in either hand.
Towing
Towingatrailerorotherattachment that istooheavycoulddamagethedriveorcausethemowerto
becomeunstable. Limit loadsto250poundsorlesson thismower.
BEFORE OPERATING MOWER:
1. Read engine manufacturer's operating and maintenance instructions.
2. Read and observe all safety instructions on your mower and in the
manual.
3. Check engine oil.
4. Be sure gas cap is in place.
5. Be sure parking brake is on.
6. Be sure mower blade drive is off.
7. Know how to stop engine. (Turn key to off position)
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
TESTING OF SAFETY INTERLOCK SYSTEMS:
PARKING BRAKE SWITCH TEST:
a) Swing out control levers
b) Disengage blade drive switch
c) Put Parking brake in OFF position
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
CONTROL LEVER SWITCH TEST: a) Disengage blade drive switch
b) Put parking brake in ON position
c) Swing control levers in
d) Turn ignition switch to START
Engine should not turn over or attempt to start.
a) Put parking brake in ON position
b) Swing out control levers
c) Engage blade drive switch
d) Turn ignition switch to START
BLADE DRIVE SWITCH TEST:
SEAT SWITCH TEST:
Engine should not turn over or attempt to start.
a) In a SAFE AREA away from bystanders,
start the engine
b) Leave levers swung out and parking brake ON
c) Engage blade drive
d) Raise slightly off seat
ENGINE SHOULD STOP
e) Disengage blade drive
f) with engine running, put parking brake
in OFF position
g) Swing levers in
h) Engage blade drive
i) Raise weight slightly off seat.
ENGINE SHOULD STOP
NOTE:
If Any Safety Check FAILS, Do Not Operate The Mower until the system has
been checked and repaired by an Authorized Dixon Dealer
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
Engage parking brake before starting engine.
CAUTION
STARTING INSTRUCTIONS:
1. Parking brake must be on, control levers swung
out, and blade drive disengaged.
2. Move throttle control to "Choke" position if
engine is cold, full throttle if warm.
3. Insert ignition key and turn to "Start" position.
When engine starts, release ignition key. Key will
return to "Run" position.
4. Move throttle from "Choke" to desired speed
position.
5. Release parking brake.
6. Swing levers in.
7. Operate the mower per the "CONTROL"
instructions on page 13.
NOTE: While mowing throttle control must be set to
the MAXIMUM or wide open setting to
insure adequate cooling of the engine and to
maintain mower deck blade speed.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A MULCHING ATTACHMENT:
Mulchingorrecyclingthegrassclippingsrequiresatotallydifferent mowingapproachthanwouldbenormal
when side discharging or bagging the grass. There may be instances or conditions where it is not possible
to hide all of the recycled or mulched clippings.
In order to achieve the best results, please read and follow the mulching tips listed below:
1.
2.
Set the engine speed control to the wide open or full setting.
Place the mower deck cut height selector in either the top or second notch. Never cut more than
3/4" to 1" off the grass at any one time. Attempting to cut more grass will result in the deck
plugging and cause the engine to stall.
3.
4.
5.
6.
7.
It may be necessary to cut the lawn twice to achieve acceptable mulching performance especially
on first cuttings or if the lawn is heavily fertilized.
Do Not Attempt To Cut Grass When It Is Wet. Mulching performance will be very poor under
wet grass conditions.
Maintain A Sharp Blade Throughout The Cutting Season. This is very important. Optimal
mulching performance cannot be obtained with a dull or nicked up blade.
Keep The Underside Of The Mower Deck Clean. Remove all grass and dirt buildup from the
underside of the pan, the baffles and deflectors after each use.
Alternate mower direction. This will evenly disperse the mulched grass clippings over the lawn
for even fertilization.
If the mulching quality of the mower does not seem to be satisfactory, try one or more of the
following tips:
1.
2.
3.
4.
5.
6.
Raise the height-of-cut setting on your mower.
It may be necessary to cut your grass more frequently.
Operate the mower at a slower ground speed.
Overlap cutting swaths instead of cutting a full swath with each pass.
Mow across the marginal areas a second time.
CUT HIGH - MOW OFTEN!
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
MOWING WITH A GRASS CATCHER ATTACHMENT:
In order to achieve optimum performance when mowing with a grass catching attachment, please read and
follow the tips listed below.
1. Some applications may require installation of an "Optional" weight box on the front of the mower
to offset cut grass weight.
2. Set engine speed control to the wide open or full setting.
3.
Do Not Attempt To Cut Grass When It Is Wet. Wet grass will clog both the underside of the deck and
the attachment chutes. Empty bags often to prevent plugging.
4. If the grass is tall, place the mower deck cut height selector in the top or second notch. Initially overlap
cutting swaths instead of a full swath with each pass.
5.
Keep The Underside Of The Mower Deck Clean. Frequent removal of dried grass and dirt will greatly
assist in bagging of the clippings.
6.
Maintain Sharp Blades Throughout The Cutting Season. Some grass catching attachments require "Hi-
Lift" blades.
7. Operate the mower at a slower ground speed than when mowing without a grass catching attachment.
CAUTION
•
•
•
Watch for low hanging branches or other obstacles which might hit the catcher top while turning or
backing the mower.
Use care when backing to avoid pushing the grass bags into the frame or "hot" exhaust muffler of the
engine.
Disengage blade and stop engine prior to clearing grass from either the discharge chute or grass catcher
components.
•
•
Keep all attachment bolts tight.
Do Not operate the mower with the grass catching attachment partially removed.
•
Important:
• Do not leave clippings in the bags while the mower is stored.
• Damp grass clippings are a fire hazard if left in the bags.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION INSTRUCTIONS
SIDE DISCHARGE OF THE CLIPPINGS:
In order to achieve optimum performance when side discharging the grass clippings, please read and
follow the tips listed below.
Additional information can be found in the troubleshooting guide.
CAUTION
Be sure that deflector is properly installed on the discharge chute.
1. Set engine speed control to the wide open or full setting.
2. Do Not Attempt To Cut Grass When It Is Wet. Wet grass will clog the underside of the deck and
dischargearea.
3. If the grass is tall, place the mower deck cut height lever in the top or second notch. Initially
overlap cutting swaths instead of a full swath with each pass. Some applications may require a
second cutting.
4. Keep The Underside Of The Mower Deck Clean. Frequent removal of dried grass and dirt will allow
the clippings to discharge correctly.
5. Maintain Sharp Blades Throughout The Cutting Season.
GRASS HEIGHT SUGGESTIONS:
Correct mowing height can reduce weeds and disease by 50 to 80%
The following grass cut heights are based on adequate moisture conditions and normal thatch buildup
in a healthy lawn. Some locations and applications may require slightly different cut heights. If in
doubt, consult your local lawn professional for assistance.
Grass Types:
Best Cut Heights
Zoysia
2" - 2 1/2"
1 1/2" - 3"
1 1/2" - 3"
1 1/2" - 2"
3" - 4"
Blue Grass
Fescue Blends
St. Augustine (Mid South)
St. Augustine (Deep South)
Tifton Bermuda
Centipede
1 1/2"
1 1/2" - 2"
1 1/2" - 2"
2"
Common Bermuda
Bahia/Argentina/Pensacola
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
This portion of the owners manual deals with normal service items which can be performed by the owner. Please
rememberthat ifyouarein doubt astothecorrect serviceprocedurestobefollowed,theseandotherservicesituations
can be handled by a Dixon ZTR dealer who is familiar with the service of your mower.
MAINTENANCE SCHEDULE:
Toinsurealongandtroublefreeservicelifeofallcomponents,aregularandthoroughmaintenance
schedule should be followed. The following items should be checked after the first (10) hours of
operation and on a weekly basis, or each (40) hours of use:
1.
2.
3.
4.
5.
6.
Drive system, belts and controls.
Mower deck belts.
Tirepressures.
Tightness of all nuts and bolts.
Battery fluid level.
Engine Oil.
Before performing any maintenance, shut off engine, allow to cool.
CAUTION
ENGINE:
For engine operating and maintenance information, refer to the engine operating and
maintenance instructions furnished by the engine manufacturer, supplied with each mower.
BATTERY: Check the fluid in the battery at frequent intervals.
Keep fluid level above the plates in each cell, using distilled water.
OFF-SEASON BATTERYSTORAGE:
Identify each cable so cables can be reconnected to correct terminals.
Disconnect cables from terminals
ALWAYS disconnect ground cable first and reconnect last
Chargebattery.
DO NOT remove battery from mower.
Clean top of battery and terminals with baking soda and water.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
MOWER BLADE MAINTENANCE:
NOTE:
Observe proper blade position prior to removal.
1. Safely raise front of mower.
2. Hold or block blade from turning.
3. Loosen blade nut and remove blade.
4. When replacing blade, tighten blade nut securely. Refer to diagram.
Wear heavy, thick gloves when holding onto mower blade, avoid the sharp
edge of the blade.
CAUTION
NOTE: Be sure blade is center on pilot before tightening nut to 60 ft. lbs. torque.
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
BELT TENSION:
42" DECK:
MOWER DECK SERPENTINE BELT:
P/N 6109
Manual adjustment. Refer to illustration below.
ENGINE TO MOWER DECK BELT:
P/N 5861
Auto tensioner with spring loaded idler. No adjustment required.
50" DECK:
MOWER DECK SERPENTINE BELT:
P/N 1300
Manual adjustment. Refer to illustration below.
ENGINE TO MOWER DECK BELT:
P/N 7174
Auto tensioner with spring loaded idler. No adjustment required.
3/4"
(42"/50" SERPENTINE)
TIGHTENORLOOSEN
HEX NUT TO ACHIEVE
DIMENSIONS SHOWN
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
FORWARD TRAVEL SPEED ADJUSTMENT
1. Drive machine until hydrostats have warmed up.
2. Drive on a smooth, level surface with both levers in top speed position.
3. Ifonesidenowdrivesslightlyfasterthan theother, adjust leverstopwasher
P/N 5760 on that sidetoreduceforward rangeofcontrollever. Ifleversare
now uneven at top speed, loosen control lever mounting nut. Rotate lever
to be even with other side and tighten nut.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
NEUTRAL ADJUSTMENT
DRIVE MACHINE UNTIL HYDROSTATS HAVE WARMED UP. WITH ENGINE RUNNING AND
THE PARKING BRAKE OFF, SWING OUT THE CONTROL LEVERS. IF MACHINE STARTS TO
CREEP, FOLLOW THE INSTRUCTIONS BELOW.
1. Stop the engine, engage parking brake, and raise rear of frame with jack or blocks so that rear tires do not
contact the ground.
2. Swing out the control levers, start the engine and release the parking brake.
3. Raisetheseat toaccesshydrocontrollinkage. Ifright wheelcreeps, adjust right sidelinkage, and vice-versa. Use
procedurebelow:
a. Loosen, but do not remove, the bolt in the control tube P/N 5540.
b. Loosen Jam nuts on ends of the
coupler P/N 7736.
c. If right wheel is creeping forward,
turn coupler counter clockwise until
neutralisachieved (clockwisefor left
side). If right wheel is creeping
backward,turncouplerclockwiseuntil
neutralisachieved(counterclockwise
for left side).
d. Tighten jam nuts against coupler.
e. Tighten bolt in control tube.
4. Lower seat, release parking brake, and swing control levers in. If wheel creeps, repeat steps 3a & 3e.
5. Stop engine and remove rear of machine from jack or blocks.
6. Drive machine with both levers in top speed
position. If one side now drives slightly faster
than the other, adjust lever stop washer P/N
5760 on that side to reduce forward range of
control lever. If levers are now uneven at top
speed, loosen control lever mounting nut.
Rotate lever to be even with other side and
tighten nut.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
MOWER DECK LEVELING PROCEDURE:
1. Place mower on a smooth, level surface and check tire pressures to insure correct stance. Tires
should be inflated as follows:
Front: 16 - 21 lbs
Rear: 8 - 14 lbs
2. Turn each outer blade tip to align with the deck in a side to side manner.
3. Measure from the floor surface up to the bottom of the blade tip on the discharge side of the
mower. Retain this measurement. Move to the opposite side and check to see if that measurement
is the same. If adjustment is required, turn nut on one or both of the rear L-rods until both
measurements are equal.
4. Turn each outer blade tip to align with the deck in a front to rear manner.
5. Measure from the floor surface up to the bottom of the blade tips at both the front and rear of the
blades. Rear of blade tips should be to 1/8" to 3/8" higher that the front of blade tips. If
adjustment is necessary, turn nut on front L-rod.
NOTE: This will place the mower deck in a base measurement position. Additional adjustment may
be required to achieve desired cut for the type of grass or conditions involved.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
42" and 50" DECK REMOVAL:
1. Place cut height lever in lowest cut position.
2. Pull belt idler back to allow belt to be removed from idler pulley and
electric clutch pulley.
3. Remove hair pin cotter and washer from one end of deck support cross
shaft. Note location of remaining shim washers used between chassis
and mower deck plates. Slide shaft from chassis and mower deck.
4. Remove hair pin cotter and washer from each deck L-rod. Remove L-
rods from lift arms. At this point, deck will drop down.
5. Carefully raise and support front of chassis. Slide mower deck to either
side for removal. (Reverse procedure to reinstall deck assembly).
NOTE: When deck is reinstalled on frame, check that belt is correctly
routed in the groves of all pulleys and that belt idler is
applying tension to the back side of the belt.
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
HOT oil may cause burns. Allow engine to cool before draining oil.
CAUTION
CHANGING THE ENGINE OIL:
1. The "snap lock" oil drain valve is located on the left side of the
engine crankcase.
2. Place a suitable container under the drain valve. The fitting of a short
piece of hose to the valve will help direct the oil.
3. Push the valve body in and twist to clear the detent notch.
4. Pulling the valve body outward will start the flow of oil.
NOTE: Refertoenginemanufacturer'srecommendationsforfrequencyofoilchanges.
BRIGGS & STRATTON
KOHLER
PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS.
-PROTECT YOUR ENVIRONMENT-
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
OIL FILL:
1. Push the valve body
in and twist into the
detent notch.
Closed
Open
2. Clean any spilled oil from engine and chassis.
3. Refill engine with type, and quantity of oil recommended by the engine manufacturer in
engine literature.
NOTE:
Oil changes require replacement of the oil filters. These filters can be obtained from your
authorized engine dealer.
The use of any other oil filter may cause damage to the engine.
Briggs & Stratton Oil Filter: P/N 492 932
Kohler Oil Filter: P/N 52 050 02
PLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS.
-PROTECT YOUR ENVIRONMENT-
LUBRICATION:
CHASSIS:
(7) grease zerks used on 42" & 50"
LOCATIONS:
(1) each front wheel caster tube and front
wheel hub. (1) each mower deck hub.
SERVICEINTERVALS:
Every 50 hours of operation
RECOMMENDED GREASE:
Name brand wheel bearing or multi-purpose grease
Lubricateeach front wheeltoalloweven distribution ofgreasewithin the
wheel, rotate or spin each front wheel after (3) pumps of the grease gun.
Repeat processuntiltheappearanceofgreaseisnoted completelyaround
each caster axle.
BRAKE SYSTEM:
Use penetrating lubrication to keep all brake parts functioning
smoothly. Lubricate at locations illustrated.
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE AND MAINTENANCE
WHEELS AND TIRES:
Correct tire pressure is important for correct operation
of mower.
Front Tires 11 X 4.00 X 5
Rear Tires 18 X 8.50 X 8
16-21 PSI
8-14 PSI
NOTE: Check lug nuts periodically for tightness.
Keep all connections clean and tight.
ELECTRICAL SYSTEMS:
CLEANING THE MOWER: Wash mower periodically.
Clean above and below deck.
NOTE: Allow mower to cool before washing. If
bearings are hot, they will draw moisture
inside as they dry and cause corrosion.
SERIALNUMBERS:
The serial number is located on frame at rear of engine,
it will begin with DM.
WARRANTY:
Refer to Warranty Registration Form (P/N 5859).
PARTS/SERVICE:
See your Dixon dealer for replacement parts, warranty
or service.
PLEASE HELP PROTECT THE ENVIRONMENT BY AVOIDING ALL
CHEMICALS WHICH MAY DAMAGE OR CAUSE HARM TO PLANTS AND
ANIMALS IN YOUR AREA.
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
STANDARD SERVICE PARTS LIST
42" DECK:
BLADES:
BELTS:
Standard Hi-Lift:
Lo-Lift:
P/N 8688
P/N 6236
Engine To Mower Deck:
SerpentineBelt:
Engine To Transmission:
P/N 5861
P/N 6109
P/N 5768
50" DECK"
BLADES:
BELTS:
Standard Hi-Lift:
Lo-Lift:
P/N 9444
P/N 9443
Engine To Mower Deck:
SerpentineBelt:
Engine To Transmission:
P/N 7174
P/N 1300
P/N 5768
BRIGGS & STRATTON FILTER PART NUMBERS:
Please refer to Briggs & Stratton Engine Operators Manual for correct service intervals
for engine oil changes and air filter maintenance.
Protect your engine investment, use only original equipment filters.
PrecleanerFoam Element
Air Filter Cartridge:
Engine Oil Filter:
P/N 272 403
P/N 493 909
P/N 492 932
KOHLER FILTER PART NUMBERS:
Please refer to Kohler Engine Operators Manual for correct service intervals for engine oil
changes and air filter maintenance.
Protect your engine investment, use only original equipment filters.
Air Filter Cartridge:
Pre-Cleaner:
P/N 12 08 310
P/N 12 08 312
Engine Oil Filter:
P/N 52 050 02
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
MOWER CUT QUALITY:
Therearemanyvariablesthat can effect thecut qualityofanyridingmower. Typeand conditionsofgrass,
cut height setting,engineRPM andgroundspeedaresomeofthevariablesthat interact creatingdifferences
in cut quality. Examination of one or more of the above will generally produce a quality cut.
TheTroubleshootingChart suggestspracticesandadjustmentsthat maybehelpfulinimprovingcut quality.
Your Dixon ZTR dealer is also available to provide assistance to you.
SITUATION
CAUSES
REMEDY
Poor cut quality
Ground speed
Reduce mowing speed
Poor cut quality
Incorrect engine to
mower deck belt
Refer to page 31 for part numbers
Poor cut quality
Poor cut quality
Poor cut quality
Poor cut quality
Engine RPM too low
Dull or bent blade
Increase engine RPM to maximum
Sharpen or replace as required
Un-level mower deck
Refer to page 26 for deck leveling
procedure
Grass buildup under
mower deck
Clean out underside of mower deck
Poor cut quality
Poor cut quality
Improper blades
Refer to page 31 for part numbers
Uneven tire pressures
Refer to page 30 for correct tire
pressures
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
DRIVE SYSTEM:
SITUATION
CAUSES
REMEDY
Mower creeps in
neutral position
Neutral adjustment
Refer to page 25 for procedure or consult
your dealer for repair
Mower pulls to one side Forward travel speed
or the other adjustment
Refer to page 24 for procedure
Loss of power and speed Incorrect or worn drive belt Replacebelt
on both sides
Spring on idler arm missing Replace spring
or broken
Idler arm will not pivot
Internal malfunction
Remove cause of seizure and lubricate
Consult your dealer for repairs
Drive system functions
on one side only
Incorrect or worn drive belt Replacebelt
Spring on idler arm missing Replace spring
or broken
Idler arm will not pivot
Internal malfunction
Remove cause of seizure and lubricate
Consult you dealer for repairs
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
ELECTRICAL SYSTEM:
SITUATION
CAUSES
REMEDY
Starter will not
turn engine over
Circuit breaker disengaged Push button to reset
Consult your dealer for repair
Starter will not
Dead Battery
Chargebattery
turn engine over
Batterydischarge
Poor connections on
battery
Tighten or replace as required
Battery water low
Wrong battery installed in
mower
Batterydischarge
Batterydischarge
Engine electrical system not Have electrical system checked by your dealer
functioning correctly
Engine not being operated
at full throttle
Increase engine RPM
Contact your dealer for information
NOTE: Electrical system failures are generally simple in nature, always check the obvious first and
then move onto the more complicated parts used.
Poorbatteryservice,looseconnections,corrosion,frayedorbroken wiring,aremorelikelythan
component failure.
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER
INFORMATION
DIXON INDUSTRIES,INC.
A BLOUNT International Inc. Co.
PO BOX 1569
COFFEYVILLE KS 67337 0945
316 251 2000
FAX 316 251 4117
DATE PURCHASED
MOWER MODEL NUMBER
MOWER SERIAL NUMBER
DM-
PURCHASED FROM
Name
Address
DATE OIL CHANGED:
DATE ENGINE TUNED:
Download from Www.Somanuals.com. All Manuals Search And Download.
The Engine Exhaust from this product contains chemicals known to the State of
California to cause cancer, birth defects or other reproductive harm.
WARNING:
Dixon® and ZTR® are registered trademarks of Dixon Industries, Inc.
DIXON INDUSTRIES, INC.
A BLOUNT International Inc. Co.
PO BOX 1569
COFFEYVILLE KS 67337 0945
316 251 2000
4500 Series
4515B&4516K
Part No. 1857-0599
Download from Www.Somanuals.com. All Manuals Search And Download.
|