Dixon Lawn Mower 14295 1005 User Manual

ZEETER  
ZEETER™  
Safety Instructions  
&
Operator’s Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Page  
SAFETY& WARNING....................................4-15  
WARRANTY.........................................................16  
SPECIFICATIONS..............................................17  
CONTROLS...................................................18-22  
OPERATIONINSTRUCTIONS....................23-31  
CARE & MAINTENANCE............................32-44  
STANDARD SERVICE PARTS LIST...............45  
TROUBLESHOOTING..................................46-47  
ZEETER™  
Part Number 14295-1005  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
RIDING LAWN MOWERS,  
IF IMPROPERLY OPERATED  
CAN CAUSE SERIOUS INJURY OR DEATH  
Pictured below are the most common causes of injury to  
the operator or bystander. Please read and understand  
this manual to prevent injuries.  
Blade Contact  
Tip Over  
Run Over  
Back Over  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY  
Safety Alert Symbol  
When you see this symbol, BE ALERT  
to the potential for injury.  
Follow the recommended safety precautions and  
safe operating practices.  
DANGER  
(highlighted in red)  
indicates an imminently hazardous  
situation which, if not avoided, will result  
in death or serious injury.  
WARNING  
(highlightedin orange)  
indicates a potentially  
hazardous situation which, if not  
avoided, could result in death or  
serious injury.  
CAUTION  
(highlighted in yellow)  
indicates a potentially  
hazardous situation which,  
if not avoided, may result in minor  
or moderate injury. It may also  
be used to alert against  
unsafe practices.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
GENERAL OPERATION:  
Read, understand, and follow all instructions in this  
manual and on the mower before starting.  
Only allow responsible adults, who are familiar with the  
instructions, to operate the mower.  
Clear the area of objects such as rocks, toys, wire, etc.,  
which could be picked up and thrown by the blade.  
Be sure the area is clear of other people before mowing.  
Stop mower if anyone enters the area.  
Be aware of the mower discharge direction and do not  
point it at anyone. Mower blades can throw rocks or other  
debris.  
Do not operate the mower without either the entire grass  
catcher or the deflector in place. This will decrease the  
possibility of injury from objects being thrown by the  
mower blades.  
Never carry passengers. They may fall off and become  
seriously injured or interfere with safe operation of the  
mower.  
Mowing in reverse is not recommended because it is  
difficult to maintain a clear vision of the mowing path.  
However, should it become necessary to back up,  
remember to look down and behind before and while  
backing.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
GENERAL OPERATION (continued):  
Never leavea running mower unattended. Always turn off  
blades, set parking brake, stop engine and remove key  
before dismounting.  
Turn off blades when not mowing. Injurycould occur from  
contact with moving parts.  
Under no circumstances should you place hands or feet  
under the mower deck or in the chute while blades or  
impeller arestill running.  
To avoid personal injury from accidental clutch engage-  
ment, stop engine before removing grass catcher or  
uncloggingchute.  
Mow only in daylight or good artificial light.  
Do not operate the mower while under the influence of  
alcohol or drugs.  
Slow down before turning to reduce the risk of tip-over.  
Watch for traffic when operating near or crossing road-  
ways.  
Use extra care when loading or unloading the mower into  
a trailer or truck. Push, do not ride the mower when  
loading and unloading.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
GENERAL OPERATION (continued):  
Never dismount mower without applying parking brake  
or stopping engine.  
Protect your eyes.Always wear safety goggles or safety  
glasses with side shields when operating mower.  
Data indicates that operators, age 60 years and above,  
are involved in a large percentage of riding mower-  
related injuries. These operators should evaluate their  
ability to operate the riding mower safely enough to  
protect themselves and others from serious injury.  
To protect against possible tip-over, follow the  
manufacturer’s recommendation for wheel weights and  
counterweights.  
Maintain or replace safety & instruction labels as  
needed.  
The engine exhaust from this product contains chemicals known to the State of  
California to cause cancer, birth defects or other reproductive harm.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
SLOPE OPERATION:  
Slopes are a major factor related to loss-of-control  
and tip-over accidents, which can result in  
severe injury or death.  
All slopes require extra caution. If you feel uneasy  
on a slope, do not mow it!  
DO  
Mow across the slope with your Dixon® ZTR® --  
never up or down. This will decrease the risk of  
tip-over.  
Remove obstacles such as rocks, tree limbs, wires  
and other foreign objects that can be thrown by  
mower blades.  
Watch for holes, ruts, roots and bumps. Uneven  
terrain could overturn the mower. Tall grass can  
hide such obstacles.  
Use slow speed. Tires may lose traction on slopes  
even though the brakes are functioning properly.  
Avoid starting or stopping on a slope. If tires lose  
traction, disengage the blades and proceed slowly  
down the slope.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
SLOPE OPERATION (continued):  
DO (continued):  
Keep all movement on the slopes slow and  
gradual. Do not make sudden changes in speed  
or direction.  
Use extreme caution when operating the mower  
with attachments to prevent tip-over or roll-over.  
If front wheels lift off the ground, pull levers back to  
stabilize the mower. Discontinue mowing the  
slope!  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
SLOPE OPERATION (continued):  
DO NOT  
Do not turn on slopes unless necessary, and then,  
turn slowly and gradually downhill, if possible. Rapid  
uphill turnsmaycause tip-over.  
Do not mow near drop-offs, ditches, or embank-  
ments. The mower could suddenly turn over if a  
wheel is over the edge of a cliff or ditch or if an  
edge caves in.  
Do not mow on wet grass. Reduced traction could  
cause sliding.  
Do not try to stabilize the mower by putting your foot  
on the ground.  
Do not use grass catcher or other attachments on  
steep slopes. The added weight may change the  
stability of the mower thus creating the potential for  
tip-over.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
FIRE HAZARDS:  
Use extra care when handling gasoline and other  
fuels. They are flammable and vapors are explosive.  
Store all fuel in approved containers specifically  
designed for that purpose.  
Allow engine to cool before refueling. Never remove  
fuel cap or add fuel with engine running.  
Do not smoke while refueling or operating the mower.  
To reduce fire hazard, keep mower free of grass,  
leaves and other debris build-up.  
If gasoline is spilled, do not attempt to start the  
engine. Move mower away from the area of the spill.  
Do not create any source of ignition until gas vapors  
have dissipated. Wipe up spilled fuel and dispose of  
waste properly.  
Iffuelisspilledonclothing,changeclothingimmediately.  
Before storing, allow mower to cool. Clean fuel and  
oil spillage.  
Never store the mower or fuel container inside a  
building where there is an open flame.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
FIRE HAZARDS (continued):  
To prevent fire or explosion, keep sparks and open flames  
away from battery.  
Keep electrical connections clean and tight. Inspect them  
often. Loose connections and corrosion increase fire risk.  
Before disconnecting the negative ground cable, make sure  
all switches are off. This decreases the chance of sparking  
and fire.  
Use care when backing to avoid pushing the grass  
bags into the frame or “hot” exhaust muffler of the  
engine. Fire could result.  
To prevent fire and explosion caused by static electricity:  
Never fill containers inside a vehicle or on a truck or  
trailer bed with a plastic liner. Always place containers  
on the ground away from your vehicle before filling.  
When practical, remove fuel powered equipment from  
the truck or trailer and refuel it on the ground. If this is  
not possible, refuel such equipment on a trailer with a  
portable container, rather than from a fuel dispenser  
nozzle.  
If a fuel dispenser nozzle must be used, keep the  
nozzle in contact with the rim of the fuel tank or  
container opening at all times until fueling is complete.  
Do not use a nozzle lock-open device.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
CHILDREN:  
Tragic accidents can occur if the operator is not  
alert to the presence of children.  
Children are attracted to lawn mowers and the  
mowing activity.  
NEVER assume children will stay where they  
were last seen.  
Be alert to avoid accidents.  
Keep children out of the mowing area and under the  
watchful care of another responsible adult.  
Be alert and turn mower off if a child enters the area.  
Before and during backing look BEHIND and DOWN  
for smallchildren.  
Never carry children. They may falloff and be seriously  
injured or interfere with safe mower operation.  
Never allow children to operate the mower.  
Use extra care when approaching blind corners, shrubs,  
trees, or other objects that may obscure vision.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
WARNING  
Failure to observe the following safety instructions  
could result in serious injury or death.  
SERVICE:  
Never run a mower inside a closed area or without proper  
ventilation.  
Keep nuts and bolts tight, especially blade attachment  
bolts, and keep equipment in good condition.  
Never tamper with safety devices. Check their proper  
operation regularly.  
Stop and inspect the equipment if you strike an object.  
Repair, if necessary, before restarting.  
Never make adjustments or repairs with the engine running  
unless otherwise specified.  
Grass catcher components are subject to wear, damage  
and deterioration which could expose moving parts or allow  
objects to be thrown. Frequently check components.  
Replace with original equipment parts when necessary.  
Mower blades are sharp and can cut. Wrap blades or wear  
gloves, and use extra caution when servicing them.  
Batteries contain sulfuric acid. To prevent burns, avoid  
contact with skin, eyes and clothing.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DIXON®ZTR® RESIDENTIALWARRANTY POLICY  
ZEETER™ - Residential Mower  
DIXON® WARRANTS ITS ZTR® MOWERS AGAINST DEFECTS IN MATERIAL AND WORK-  
MANSHIP FOR THE PERIODS SET FORTH BELOW. THE SOLE REMEDY UNDER THIS  
WARRANTY IS REPLACEMENT OR REPAIR OF PARTS INCLUDING LABOR COSTS.  
THIS WARRANTY IS SUBJECT TO THE FOLLOWING CONDITIONS AND LIMITATIONS:  
1. RESIDENTIALAPPLICATION - (used only at owner’s primary place of residence):  
a. TwoYears - 100%parts and labor subject to the conditions and limitations described  
herein for a period of two years from date of purchase by the original owner.  
b. Attachments marketed through or approved by Dixon Industries, Inc., are warranted  
for two years parts and labor in residential use applications.  
2. NOT APPROVED FOR COMMERCIAL USE.  
3. All Dixon® warranty must be accomplished by authorized Dixon® dealers and in  
accordance with Dixon® warranty policy and allowances. All warranty claims mustbe  
submitted to Dixon Industries for approval.  
4. Warranty applies to new and unused mowers and is transferable within the stated time  
frame to a second owner.  
5. Warranty labor reimbursement to dealers based on published Dixon® flat rate schedule.  
6. Warranty doesnot applyto damage in transit or incidents of misuse, negligence,  
accidents, or alteration. The use of parts or components other than those supplied by  
Dixon Industries VOIDSALL WARRANTY.  
7. Battery warranty is limitedto one year from mower manufacture date.  
8. The following items are not covered by this warranty policy:  
(a) Routine maintenance or adjustments toinclude any oils, filters or other fluidsused.  
(b) Belts, blades andtires.  
(c) Pick up and delivery charges for transportation of mower to and from an authorized  
Dixon® dealer’s place of business.  
(d) Engines. These are covered under a separate warranty by each individual engine  
manufacturer. Consult engine manual for warranty details.  
(e) Any costs or expense of providing substitute equipment while repair work is being  
performed on a warranted mower.  
9. THERE IS NO OTHER EXPRESS WARRANTY. TO THE EXTENT PERMITTED BY  
LAW, ALL IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY  
AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED, OTHERWISE,  
ALL SUCH IMPLIED WARRANTIES ARE LIMITED TO THE SAME DURATION  
AND REMEDIES AS THE EXPRESS WARRANTY. ALL LIABILITIES FOR CONSE-  
QUENTIAL DAMAGES UNDER ANY EXPRESS OR IMPLIED WARRANTY ARE  
EXCLUDED.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SPECIFICATIONS  
CHASSIS:  
BODY:  
11GAweldedchannelframe  
Allbodypartsmadeofrotationalmoldedpolyethylene.  
Frontbodycontainsaccesspanelfor batteryservice.  
Seattilts forwardtoallowtransmissionservice.  
MOWERDECK:  
11GAstampedsteelconstruction. Single30cutblade.  
Cutheight approximately1-1/2”-4” via7-positionlift  
handle.  
BLADEDRIVE:  
Mechanical;handleverengagement  
TRANSMISSION:  
Eachrearwheelisindependentlydrivenbychainand  
sprocketsthrougha frictionmechanicaldrive.  
ENGINE:  
11HPBriggs&Stratton I/C, 4-cycle,singlecylinder,air-  
cooled,gasoline, verticalshaft,aluminum headandblock.  
STARTINGSYSTEM: Electricbykeyswitchoperationwithsafetyinterlockson  
parkingbrakeand bladedrive.  
TIRES:  
Front  
Rear  
9 x 3.50-4 Smooth Tread  
16x 6.50-8Turf Saver  
RECOMMENDED  
TIREPRESSURE:  
Front  
Rear  
16-21PSI  
8-14PSI  
CAPACITIES:  
DIMENSIONS:  
Fuel  
Engine  
3 quart  
1.25 quarts oil  
Width  
Width  
Height  
Length  
Weight  
32” outsiderear wheelmeasurement  
40” overallwidthof deck with deflector  
31” to top edge of seat  
65.5” hitch tab to front  
390 lbs.  
Additional information may be provided elsewhere in this manual.  
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
CONTROL LEVERS  
TO GO FORWARD  
•From neutral position, gently push control levers for-  
ward.  
To increase speed, move levers further forward.  
TO GO BACKWARDS  
•From neutral position, gentlypull control levers toward  
you.  
TURNING  
•Turningis controlled by moving one control lever slightly  
forward or rearward of the other.  
To turn left, move left lever rearward of the right lever.  
To turn right, move right lever rearward of the left lever.  
To turn on mower’s own axis (zero turning radius), stop  
and move one lever to reverse position and the other to  
forward position.  
BRAKING  
To brake mower, move both levers in direction opposite  
of travel.  
LEFT TURN OPPOSITE  
Note: The pressure required to operate the mower is very light.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
PARKING BRAKE:  
The parking brake is designed to hold  
the mower from moving and is not  
intended for use in stopping the  
mower while it is in motion. The  
engine will stop if the parking brake is  
engaged while the control levers are in  
the drive position.  
Engage parking brake  
CAUTION  
before starting engine.  
TO SET PARKING BRAKE:  
The hand operated parking brake is located on the  
right side of the mower.  
To engage brake, pull lever up (to the rear).  
To release brake, move lever forward (down).  
Note: Always set parking brake before dismounting.  
Release parking brake before moving mower.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
BEFORE OPERATING MOWER:  
1. Read engine manufacturer’s operating and  
maintenance instructions.  
2. Read and observe all safety instructions  
on your mower and in the manual.  
3. Check engine oil.  
4. Check fuel cap to be sure it is in place.  
5. Be sure parking brake is on.  
6. Be sure mower blade drive is off.  
7. Know how to stop engine. (Turn key to off  
position).  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
The Dixon® ZEETER™ has a unique transaxle that  
requires only two drive levers to control braking, turning,  
speed and direction.  
On initial operation set throttle speed to slow. Operate  
with mower blade in “OFF” position.  
To avoid “over-controlling” the mower, use a light touch  
on the drive levers.  
Slight movements using fingertip control is all that is  
necessary.  
TRANSMISSION DRIVE SYSTEM  
Allows the mower to turn on its own axis “ZERO  
TURNING RADIUS”. Each lever controls one side of the  
mower.  
Note: The pressure required to operate the mower is very light.  
TOWING TRAILERS AND OTHER  
ATTACHMENTS:  
Towing a trailer or other attachment that is too heavy  
could damage the drive or cause the mower to become  
unstable. Limit loads to 250 pounds or less with this  
mower.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTROLS  
BLADE DRIVE:  
•Located to the left of the operator.  
To engage the mower blade, turn lever  
on floor slowly to the “ON” position.  
To disengage mower blade, turn lever to  
the “OFF” position.  
THROTTLE CONTROL LEVER:  
•Located on control panel to operator’s  
right.  
•Throttle control for engine speed.  
•Choke for engine starting.  
•Throttle control should be set to  
MAXIMUM or wide open setting to insure  
adequate cooling of the engine and to  
maintain mower deck blade speed while  
mowing.  
MOWER DECK CUT HEIGHT LIFT LEVER:  
Located to the left of the operator.  
Controls the cutting height.  
Seven positions of adjustment.  
Move lever in and forward to lower.  
Move lever in and back to raise.  
Note: Always use high for transport.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
The safe and successful operation of  
the ZEETER™ mower will depend upon  
the operator having the correct  
knowledge of all controls used on the  
mower and making good judgements  
about the terrain to be mowed.  
NEVER allow anyone to operate the  
mower without complete knowledge of  
all controls and their functions.  
NEVER dismount mower without  
applying parking brake or stopping  
engine.  
During initial operation, “learning to  
drive”, set throttle at slow speed.  
Sound judgement by the operator will  
prevent accidents.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
CAUTION  
Failure to follow these instructions may  
result in personal injury.  
STARTING INSTRUCTIONS:  
1. Parking brake must be on and blade drive disengaged.  
2. Position throttle lever to 1/2 speed setting. If engine is cold,  
position lever to the choke position.  
NOTE:  
Engine may require choke setting to start even if the  
engine has been operated for a period of time.  
3. Insert ignition key and turn to “start” position. When engine  
starts, release ignition key. Key will return to “run” position.  
4. Move “throttle” from choke to maximum speed position.  
5. Release parking brake.  
6. Operate mower per “CONTROLS” instructions on Page 18.  
CAUTION Do not operate the engine in an  
enclosed area due to the  
harmful exhaust gas produced.  
Note:  
When mowing with blades  
engaged, set throttle control to  
the MAXIMUM or wide open  
setting to insure adequate  
cooling of the engine and  
to maintain mower deck blade  
speed.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
TESTING OF SAFETY INTERLOCK SYSTEMS:  
Failure to observe the following testing instructions  
could result in serious injury or death.  
The following tests should be performed at the start  
of each mowing day.  
PARKING BRAKE SWITCH TEST:  
a) Put parking brake in OFF position  
b) Turn ignition switch to START  
Engine should not turn over or attempt to start.  
BLADE DRIVE SWITCH TEST:  
a) Put parking brake in ON position  
b) Engage blade drive switch.  
c)Turn ignition switch to START.  
Engine should not turn over or attempt to start.  
SEAT SWITCH TEST:  
a) In a safe area away from bystanders, start the  
engine.  
b) Engage blade drive switch.  
c) Raise slightly off seat.  
Engine should STOP!  
NOTE: If any safety check fails, do not operate the  
mower until the system has been checked and repaired  
by an Authorized Dixon® Dealer!  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
MOWING WITH A MULCHING ATTACHMENT:  
Mulching or recycling the grass clippings requires a  
totally different mowing approach than would be normal  
when side discharging or bagging the grass. There  
may be instances or conditions where it is not possible  
to hide all the recycled or mulched clippings.  
In order to achieve the best results, please read and  
follow the mulching tips listed below:  
1. Read and follow the installation instructions that are  
included with your mulcher.  
2. Set the engine speed control to the wide open or full  
setting.  
3. Place the mower deck cut height selector in either  
the top or second notch. Never cut more than 3/4” to  
1” off the grass at any one time. Attempting to cut  
more grass will result in the deck plugging and cause  
the engine to stall.  
4. It may be necessary to cut the lawn twice to achieve  
acceptable mulching performance especially on first  
cuttings or if the lawn is heavily fertilized.  
5. Do not attempt to cut grass when it is wet. Mulching  
performance will be very poor in wet grass conditions.  
6. Maintain sharp blades throughout the cutting season.  
This is very important. Optimal mulching performance  
cannot be obtained with a dull or nicked up blade.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
MOWING WITH A MULCHING ATTACHMENT  
(continued):  
7. Keep the underside of the mower deck clean.  
Remove all grass and dirt build-up from the  
underside of the pan, the baffles and deflectors  
after each use. Never, under any circumstances,  
should you place hands or feet under the  
mower deck or in the chute while blades or  
impeller are still turning.  
8. Alternate mower direction. This will evenlydisperse  
the mulched grass clippings over the lawn for even  
fertilization.  
If the mulching quality of the mower does not seem  
to be satisfactory, try one or more of the following  
tips:  
a. Raise the height-of-cut setting on your  
mower.  
b. It may be necessaryto cut your grass  
more frequently.  
c. Operate the mower at a slower ground  
speed.  
d. Overlap cutting swaths instead of cutting  
a full swath with each pass.  
e. Mow across the marginal areas a second  
time.  
f. CUT HIGH- MOW OFTEN!  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
MOWING WITH A GRASS CATCHER  
ATTACHMENT:  
In order to achieve optimum performance when  
mowing with a grass catching attachment, please  
read and follow the tips listed below.  
1. Read and follow the installation instructions that are  
included with your grass catcher.  
2. Set engine speed control to the wide open or full  
setting.  
3. Do not attempt to cut grass when it is wet. Wet  
grass will clog both the underside of the deck and  
the attachment chutes. Empty bags often to  
prevent plugging.  
4. If the grass is tall, place the mower deck cut height  
selector in the top or second notch. “Initially” overlap  
cutting swaths instead of a full swath with each  
pass.  
5. Keep the underside of the mower deck clean.  
Frequent removal of dried grass and dirt will greatly  
assist in bagging of the clippings. Never, under  
any circumstances, should you place hands  
or feet under the mower deck or in the chute  
while blades or impeller are still turning.  
6. Operate the mower at a slower ground speed than  
when mowing without a grass catching attachment.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
MOWING WITH A GRASS CATCHER  
ATTACHMENT (continued):  
7. Maintain sharp blades throughout the cutting  
season. Some grass catching attachments require a  
“high-lift” blade. See your dealer for advice on the  
type of blade(s) needed for your mower.  
8. Some mowing applications/use of grass catchers  
may require that an additional weight kit be fitted to  
the mower to counter the weight of grass in the bags.  
Please consult with your dealer for more information  
regarding installation and adding weight to the box.  
Failure to observe the following instructions  
may result in personal injury.  
WARNING  
•Watch for low hanging branches or other obstacles which might hit  
the catcher top while turning or backing the mower.  
•Use care when backing to avoid pushing the grass bags into the  
frame or “hot” exhaust muffler of the engine. Fire could result.  
•Disengage blade and stop engine prior to clearing grass from  
either the discharge chute or grass catcher components.  
Do not operate the mower with the grass catching attachment  
partially removed. Operator or bystanders could be injured by  
thrown objects.  
•Keep all attachment bolts tight.  
Important: Do Not leave clippings in the bags while the mower is  
stored. Damp grass clippings are a fire hazard if left in the bag.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
SIDE DISCHARGE OF THE CLIPPINGS:  
In order to achieve optimum performance when side  
discharging the grass clippings, please read and follow  
the tips listed below. Additional information can be  
found in the Troubleshooting guide.  
CAUTION To avoid personal injury, be sure that the  
deflector is properly installed on the  
discharge chute.  
1. Set engine speed control to the wide open or full  
setting.  
2. Do not attempt to cut grass when it is wet. Wet  
grass will clog the underside of the deck and  
discharge area.  
3. If the grass is tall, place the mower deck cut height  
lever in the top or second notch. “Initially” overlap  
cutting swaths instead of a full swath with each pass.  
Some applications may require a second cutting.  
4. Keep the underside of the mower deck clean.  
Frequent removal of dried grass and dirt will allow  
the clippings to discharge correctly. Never, under  
any circumstances, should you place hands or  
feet under the mower deck or in the chute while  
blades or impeller are still turning.  
5. Maintain sharp blade(s) throughout the cutting  
season.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION INSTRUCTIONS  
GRASS HEIGHT & CUTTING SUGGESTIONS:  
Do not attempt to cut grass when it is wet.  
If the grass is tall, place the mower deck cut height  
lever in the top or second notch. “Initially” overlap  
cutting swaths instead of a full swath with each pass.  
Some applications may require a second cutting.  
Keep the underside of the mower deck clean.  
Maintain sharp blades throughout the cutting season.  
As a rule of thumb, never cut off more than 1/3 of the  
total grass blade length. Correct mowing height can  
reduce weeds and disease by 50% to 80%.  
The following grass cut heights are based on adequate  
moisture conditions and normal thatch build-up in a  
healthy lawn. Some locations and applications may  
require slightly different cut heights. If in doubt, consult  
your local lawn professional for assistance.  
Grass Types  
Bermudagrass  
Bluegrass  
Buffalograss  
Ryegrass  
Best Cut Heights  
1 - 2”  
2 - 3”  
11/2 -3”  
2 - 3”  
3-31/2”  
Tall Fescue  
Zoysiagrass  
1 - 3”  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
WARNING  
Failure to observe the following instructions may result in personal injury.  
Before performing any maintenance, turn off engine,  
allow to cool & remove key.  
Use extreme care when working on machinery.  
Do not wearwatch or jewelry.  
Do not wear loose fitting clothes, and observe all  
common safety practices with tools.  
MAINTENANCE SCHEDULE  
Check deck drive belt..........................................after 20 hours break-in  
Check crankcase oil level..............................................before each use  
Clean grass & debris from muffler & manifold area............before each use  
Check air intake screen...................................................after each use  
Clean grass under deck...................................................after each use  
Check tire pressure.........................................................every 10 hours  
Inspect blades for sharpness............................................every 10 hours  
Clean air filter element.....................................................every 25 hours  
Grease all zerks.............................................................every 50 hours  
Check all belts................................................................every 50 hours  
Change engine crankcase oil.......................................(5 hours break-in)  
every 50 hours  
Change engine oil filter....................................................every 50 hours  
Replace air filter element..............................annually or every 100 hours  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
CUTTER BLADE MAINTENANCE:  
CAUTION Stop engine and remove ignition key  
for safety. Wear heavy, thick gloves  
when holding onto cutter blade, avoid  
the sharp edge of the blade.  
Check sharpness of mower blades after every 10  
hours of operation. Observe proper blade position  
prior to removal.  
1. Safely raise front of mower.  
2. Hold or block blade from  
turning.  
3. Loosen blade bolt and remove  
blade.  
4. When replacing blade, tighten  
blade bolt securely. Refer to  
diagram. Be sure blade is  
centered on pilot before  
tightening nut to 60 ft. lbs.  
Blades should be discarded when worn excessively.  
DANGEROUS!  
DO NOT USE  
BLADE IN THIS  
CONDITION!  
New Blade  
When notch starts,  
discard blade  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
ENGINE:  
For complete maintenance and operating information of  
the engine, please refer to the maintenance instructions  
furnished bythe engine manufacturer included in your  
Zero Turn Radius mower information packet.  
Battery contains sulfuric acid electrolyte which  
is poisonous and corrosive.  
CAUTION  
BATTERY:  
This is a maintenance-free batteryand the fluid level  
cannot be checked.  
•Charge battery if required.  
OFF SEASON BATTERY STORAGE:  
•DO NOT remove battery from mower.  
•Clean top of battery and terminals with baking soda  
and water.  
•Identify each cable so they can be reconnected to the  
correct terminal.  
•Disconnect cables from terminals. ALWAYS discon-  
nect ground cable first and reconnect last.  
•Charge battery.  
Note:  
Your Dixon® mower comes equipped with a quick  
disconnect harness for the optional Dixon® Battery  
Manager. The Dixon® Battery Manager maintains the  
proper charge levels during periods of inactivityand  
mayprevent premature batteryfailures. Contact your  
dealer for more information.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
LUBRICATION:  
CHASSIS:  
(5) grease zerks  
LOCATIONS:  
(1) each front wheel caster  
(1) each front wheel hub  
(1) each mower deck hub  
SERVICE INTERVALS:  
Every 50 hours of operation or  
once per season.  
RECOMMENDED  
GREASE:  
Name brand wheel bearing  
or multi-purpose grease  
(3 pumps each)  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
TIRES:  
Correct tire pressure is essential for efficient operation  
of the mower. Check tire pressure periodically. Inflate  
tires to the pressure listed below.  
Front tires  
Rear tires  
9 x 3.50 - 4 16-21 lbs.  
16 x 6.50 - 8 8-14 lbs.  
Lug nuts or lug bolts should be checked regularly for tightness.  
BELTS:  
Check belts every 50 hours. Replace any belts found to  
be in poor condition.  
BELT TENSION:  
Engine to Transmission Belt - P/N 7650  
Manualadjustment.  
Engine to Mower Deck Belt (manual clutch) - P/N 7725  
No adjustment required.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
ELECTRICAL SYSTEMS:  
Keep all connections clean and tight.  
CLEANING THE MOWER:  
Wash mower periodically. Clean above and below  
deck.  
High pressure washing and alkaline based soaps can  
cause damage to bearings and other parts of the  
mower. After washing your mower, start the engine and  
engage the mower deck for a few minutes to disperse  
any water that may have accumulated in bearings,  
pulleysorfans.  
Note:  
Allow mower to cool before washing. If  
bearings are hot, they will draw moisture  
inside as they dry and cause corrosion.  
SERIAL NUMBERS:  
The serial number is located on frame at rear of engine.  
WARRANTY:  
Refer to warranty information (page 16).  
PARTS/SERVICE:  
See your Dixon® dealer for replacement parts, warranty  
or service.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
HOT oil may cause burns. Allow  
engine to cool before draining oil.  
CAUTION  
CHANGING THE ENGINE OIL:  
1. The oil drain valve is located on the lower left side of  
the engine crankcase.  
2. Place a suitable container under the drain valve.  
3. To drain, remove plug from 90 degree fitting.  
4. After engine is drained, replace drain plug.  
NOTE:  
Refer to engine manufacturer’s recommenda-  
tions for frequencyof oil changes.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
HOT oil may cause burns. Allow  
CAUTION  
engine to cool before draining oil.  
OIL FILL:  
1. Clean any spilled oil from engine and chassis.  
2. Refill engine with type, and quantity of oil recom-  
mended by the engine manufacturer in engine  
literature.  
NOTE: Engine oil changes on the ZEETER™ mower  
will require replacement of the oil filter. These  
filters may be available from your local  
Dixon® Dealer.  
Protect your environment. Please dispose of used oils at  
proper collection centers.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
MOWER DECK LEVELING PROCEDURE:  
1. Place mower on a smooth, level surface and check  
tire pressures to insure correct stance. Tires should  
be inflated as follows.  
Front: 16 - 21 lbs  
Rear: 8 - 14 lbs  
2. Turn blade so tips align with the deck in a side to  
side manner.  
3. Measure from the floor surface up to the bottom of  
the blade tip on the discharge side of the mower.  
Retain this measurement. Move to the opposite side  
and check to see if that measurement is the same. If  
adjustment is required, turn nut on one or both of the  
rear L-rods until both measurements are equal.  
4. Turn blade so tips align with the deck in a front to  
rear manner.  
5. Measure from the floor surface up to the bottom of  
the blade tip at both the front and rear of the blade.  
Rear blade tip should be 1/8" to 1/4" higher than the  
front blade tip. If adjustment is necessary, turn nut on  
front L-rod.  
(See Illustration A, page 41)  
NOTE: This will place the mower deck in a base measurement  
position. Additional adjustment may be required to  
achieve desired cut for the type of grass or conditions  
involved.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
IllustrationB  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
REAR CHAIN ADJUSTMENT:  
Stopengine,removekeyandsetparking  
brakebeforeattemptingtoadjusttherear  
chain.  
CAUTION  
Proper tension for the rear chains is accomplished  
through the use of an adjuster located at mid-point of  
each rear chain.  
To adjust, tighten the nut on top of the rubber spring  
until the chain has approximately 1/4movement up and  
down when measured at mid-point. Refer to Illustration  
B, page 41.  
NOTE:  
Adjust rear drive chains after first 10 hours of  
use and every40 hours thereafter.  
NOTE: DO NOT OVERTIGHTEN CHAIN!  
Maintenance:  
Periodically remove any build-up of grass, mud or  
other debris from both the spring loaded roller and the  
upper guide rod. The use of a high quality chain lubri-  
cant is recommended.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
DECK REMOVAL:  
1. Place cut height lever in lowest cut position.  
2. Loosen belt keepers.  
3. Remove deck drive belt from engine pulley.  
4. Using a slight upward twisting motion, remove link  
from engagement handle.  
5. Turn handle fullyto the left until handle clears stop on  
mower deck pan. Lift handle then remove handle  
down through hole in lower fender.  
6. Remove hair pin cotter and washer from one end of  
deck support cross shaft. Note location of  
remaining shim washers used between chassis and  
mower deck pan arms. Slide shaft from chassis  
and mower deck.  
7. Remove hair pin cotter and washer from each deck  
adjustment rod. Carefully push each link to  
disengage from deck lift arms. At this point, deck  
will drop down.  
8. Carefully raise and support front of chassis. Slide  
mower deck to eigher side for removal. (Reverse  
procedure to reinsall deck assembly.)  
43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CARE AND MAINTENANCE  
DRIVE SYSTEM ADJUSTMENTS:  
Due to both the complex nature of the transmission and  
the number of special tools required for service, adjust-  
ments should be entrusted to your dealer.  
There are a number of simple owner service items  
which greatly influence the performance of the drive  
system.  
1. Front and rear tires must be inflated to  
proper specifications.  
2. Rear drive chain tension.  
3. Tighteness of all controls and linkages  
pertaining to the drive levers.  
4. Lubrication of both primary and final drive  
chains. The use of a high quality chain  
lubricant is highlyrecommended.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
STANDARD SERVICE PARTS LIST  
BLADES  
*Hi-Lift - P/N 13928  
Standard Lift - P/N 13927  
Gator - P/N 13929  
*Factory installed  
BELTS  
Engine to Mower Deck - P/N 7725  
Engine to Transmission - P/N 7650  
ENGINE AIR AND OIL FILTERS  
Refer to Engine Operator’s Manual for correct  
service intervals for engine oil changes and air filter  
maintenance.  
Protect your engine investment, use only original  
equipment filters. Refer to the Engine Operator’s  
Manual or ask your dealer for correct replacement  
parts.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
1. ENGINE WON’T TURN OVER  
Mower blades engaged- - - - - - - - - - - - - - - - - - - disengage blades  
Parking brake not on- - - - - - - - - - - - - - - - - - engage parking brake  
Circuit breaker trips- - - - - - - - - - - - - - - - - - - - - - - - -reset breaker  
Dead battery- - - - - - - - - - - - - - - - - - - - - - - - - - charge or replace  
Solenoid- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer  
Ignition switch- - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer  
Starter- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer  
2. ENGINE WILL TURN OVER BUT WON’T START  
No fuel- - - - - - - - - - - - - - - refuel and/or clean or replace fuel filters  
3. HARD TO START ENGINE  
Fuel line clogged- - - - - - - - - - - - - clean fuel line and check fuel filter  
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer  
4. ENGINE STARTS BUT CUTS OUT  
Water in fuel- - - - - - - - - - - - - - -drain old fuel-replace with new fuel  
Clogged fuel line- - - - - - - - - - - - - - - - - - - - - - - - - - check fuel filter  
Fuel tank vent plugged- - - - - - - - - - - - - - - - - - - - - -clean fuel vent  
Faulty fuel pump- - - - - - - - - - - - - - - - - - - - - - - - - - consult dealer  
5. ENGINE OVERHEATED  
Air intake screen or fins clogged- - - - - -clean intake screen and fins  
Oil level too low or too high- - - - - - - - - - - - - - - - - - - -adjust oil level  
Running engine too slow - - - - - - - - - - - - - - - - - -run engine faster  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
6. ENGINE RUNS BUT MOWER WON’T MOVE FORWARD  
Drive belt broken or slipping- - - - - - - - - - - - - - - - replace drive belt  
Damaged transmission- - - - - - - - - - - - - - - - - - - - - -consult dealer  
7. MOWER LOSES POWER ORTRANSMISSION OVERHEATS  
Engine air filter-- - - - - - - - - - - - - - - - - - - - - - - - - - clean or replace  
Transmission damage- - - - - - - - - - - - - - - - - - - - - - -consult dealer  
8. ENGINE STALLS WHEN BLADES ARE ENGAGED  
Operator not on seat- - - - - - - - - - - - - - - - - - - - - - - - - -sit on seat  
Faulty interlock system- - - - - - - - - - - - - - - - - - - - - - consult dealer  
Fauty blade spindle bearing - - - - - - - - - - - - - - - - - - consult dealer  
Deck drive belt not properly routed- - - - - - - - - - - - - - - - - - reroute  
Blades blocked by foreign material - - - - - - - - - - - clean under deck  
9. DRIVE SYSTEM  
Mower pulls to side- - - - - - -check tire inflation/adjust control linkage  
Mower creeps in neutral- - - - - - - - - - - - - - - - adjust control linkage  
Low on power- - - - - - - - - - - - - - - - - - - - - - - - - -check belt tension  
10. CUT QUALITY  
Cut uneven left to right- - - - - - - - - - - -check tire inflation/level deck  
Ends of grass blades are ragged- - - - - - - - - - - - - - sharpen blades  
Poor dispersal of grass- - - - - - - - - - clean deck/check for loose belt  
Skips in spots- - - - - - - - - - -check for loose belt/slow ground speed  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OWNER’S INFORMATION  
Date of Purchase  
Mower Model Number  
Mower Serial Number  
Purchased From  
Name  
Address  
DATE OIL CHANGED  
DATE ENGINE TUNED  
Dixon Industries, Inc.~P.O. Box 1569~Coffeyville, Ks~620-251-2000~Fax 620-251-4117  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Dixon® and ZTR® are registered trademarks of  
DixonIndustries, Inc.  
The engine exhaust from this product contains  
WARNING: chemicals known to the State of California to cause  
cancer, birth defects or other reproductive harm.  
DIXONINDUSTRIES, INC.  
P.O. Box 1569  
Coffeyville, Ks 67337-0945  
620-251-2000  
ZEETER™  
Part No. 14295-1005  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cisco Systems Network Hardware OL 12812 01 User Manual
Compaq Network Card 90W AC DC User Manual
Compaq Personal Computer 5BW474 User Manual
Compaq Personal Computer D300v Series User Manual
Cooper Lighting Landscape Lighting UCS10SR223D4 User Manual
Cornelius Ice Maker 2400 R404A User Manual
Frigidaire Air Conditioner FRA144HT2 User Manual
Furman Sound Power Supply PF Pro R User Manual
GE Dishwasher PDWT502VII User Manual
GE Double Oven 49 4540 User Manual