Dimplex Indoor Fireplace DFI2309 User Manual

PARTS AND SERVICE MANUAL  
FOR THE 23” INSERT FIREPLACE  
MODEL NUMBER:  
DFI2309  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
OPERATION  
MAIN ON/OFF FLAME ON/OFF SWITCH  
The ON/OFF switch supplies power to all unit functions. When this switch is in the ON  
position the flame effect operates without heat.  
LOW HEAT SWITCH  
The LOW HEAT ON/OFF SWITCH supplies power to the heater fan and the heater  
element. When the switch is in the ON position the heater operates on LOW.  
HIGH HEAT SWITCH  
The HIGH HEAT ON/OFF SWITCH supplies power to the heater fan and the heater  
element, when the switch is in the ON position the heater operates on HIGH. The LOW  
HEAT ON/OFF SWITCH must also be in the ON position for the high heat setting to  
operate.  
RESETTING THE TEMPERATURE CUTOFF SWITCH  
The heater is protected with a safety device to prevent overheating. Should the heater  
overheat, an automatic cut out will turn the heater off and it will not come back on  
without being reset. It can be reset by switching the ON/OFF SWITCH to OFF and  
waiting 5 minutes before switching the unit back on.  
CAUTION  
If you need to continuously reset the heater, unplug the unit and call your local dealer.  
MAIN ON/OFF  
HIGH HEAT  
LOW HEAT  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
REMOTE CONTROL  
The remote control has a range of approximately 50ft. (15.25m) it does not have to be  
pointed at the fireplace and can pass through most obstacles (including walls). It is  
supplied with one of 243 independent frequencies to prevent interference with other  
units. The frequency designation is indicated on the back of the transmitter (FIGURE 3)  
REMOTE CONTROL INSTALLATION  
1. Plug fireplace cordset into the outlet located on the side of the receiver. (FIGURE 2)  
2. Plug receiver into the wall outlet.  
3. Install a 9 volt battery into the transmitter. (FIGURE 3)  
Receiver  
Outlet  
FIGURE 2  
NOTE  
Fireplace MAIN on/off switch must be in the  
ON position prior to using the Remote Control.  
ON/OFF Remote Control may be used to  
control most other electrical devices including  
T.V.’s, stereos and lamps.  
CAUTION  
For indoor use in dry areas only  
OPEN  
For use on electrical devices with 15 amp  
resistive load or 1/3 HP inductive load  
120 volt AC only  
Frequency  
Code  
Battery  
Cover  
FIGURE 3  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
6
5
7
8
1
2
3
11  
4
12  
10  
9
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
REPLACEMENT PARTS  
23” FIREPLACE INSERT  
REPLACEMENT PART  
1. MAIN ON/OFF SWITCH  
2. LOW HEAT ON/OFF SWITCH  
3. HIGH HEAT ON/OFF SWITCH  
4. CORDSET  
5. HEATER ASSEMBLY  
6. CUTOUT  
7. MIRROR  
REPLACEMENT PART NO.  
2800090100RP*  
2800090100RP*  
2800090100RP*  
4100090101RP  
2200490300RP  
2300270200RP  
5900350100RP  
0438200200RP  
2000220100RP  
5900340100RP  
4200120100RP  
6800050200RP  
8. LOGSET  
9. FLICKER MOTOR  
10.REFLECTOR ASSEMBLY  
11.LAMPHOLDER  
12.REMOTE CONTROL  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
WIRING DIAGRAM  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
Light bulbs need to be replaced when you notice a dark section of the flame. There are  
four bulbs under the log set which generate the flames and embers.  
It is a good idea to replace all of the light bulbs at one time if they are close to the end of  
their rated life. Group replacement will reduce the number of times you need to open  
the unit to replace the light bulbs.  
1. Remove the fireplace trim.  
2. Remove the (2) outer screws from the log grate.  
3. Slide the light assembly out of the insert by pulling the log grate  
until the light assembly reaches the stop.  
4. Remove the log set by lifting the log ember bed straight up.  
5. Examine the bulb(s) to determine which bulb(s) require replacement.  
6. Unscrew the bulbs counter clockwise.  
7. Insert new bulbs.  
8. Replace the log set into the insert.  
9. Slide the light assembly back into the insert.  
10.Install the two outer screws into the log grate.  
11.Reinstall the fireplace trim.  
Log Ember Bed  
Light Bulbs  
Light Assembly  
Outer Screws  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
BULB REQUIREMENTS  
Quantity 2 clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60  
watt rating.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE MAIN ON/OFF SWITCH  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) screws located in the front middle of the top and the (2) screws at  
the back of the top.  
4. Locate the main on/off switch mounted in the exhaust panel and disconnect the  
wiring clips and connections noting their original locations.  
5. Depress the retainer clips on the rear of the switch and push the switch out of the  
exhaust panel.  
6. Properly orientate the new switch and connect all of the wiring clips and  
connections.  
7. Reassemble in the reverse order as above.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE LOW HEAT ON/OFF SWITCH  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) screws located in the front middle of the top and the (2) screws at  
the back of the top.  
4. Locate the low heat on/off switch mounted in the exhaust panel and disconnect the  
wiring clips and connections noting their original locations.  
5. Depress the retainer clips on the rear of the switch and push the switch out of the  
exhaust panel.  
6. Properly orientate the new switch and connect all of the wiring clips and  
connections.  
7. Reassemble in the reverse order as above.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE HIGH HEAT ON/OFF SWITCH  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) screws located in the front middle of the top and the (2) screws at  
the back of the top.  
4. Locate the high heat on/off switch mounted in the exhaust panel and disconnect the  
wiring clips and connections noting their original locations.  
5. Depress the retainer clips on the rear of the switch and push the switch out of the  
exhaust panel.  
6. Properly orientate the new switch and connect all of the wiring clips and  
connections.  
7. Reassemble in the reverse order as above.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE FLAME MOTOR/FLAME ROD  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) outer screws from the log grate.  
4. Slide the light assembly out of the insert by pulling and lifting up on the log grate until  
the light assembly comes out of the unit.  
5. Remove the (2) flame motor cover screws and set aside.  
6. Remove the (3) flame motor wires (black, white, and brown) from the terminal block.  
NOTE: A small Philips head screwdriver is required.  
7. Remove the (2) flame motor mounting screws.  
8. Remove flame rod from flame motor by pulling the rubber channel section of the  
flame rod away from flame motor.  
9. Reassemble in the reverse order as above.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE HEATER ASSEMBLY  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) screws located in the front middle of the top and the (2) screws at  
the back of the top.  
4. Disconnect the wiring clips and connections from the heater assembly noting their  
original locations.  
5. Remove the (4) screws located in the middle of the top panel.  
6. Remove the (2) Z brackets from the bottom of the heater assembly noting their  
mounting orientation.  
7. Install the (2) Z brackets onto the replacement heater assembly.  
8. Reassemble in the reverse order as above.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE LIGHT HARNESS  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) outer screws from the log grate.  
4. Slide the light assembly out of the insert by pulling and lifting up on the log grate until  
the light assembly comes out of the unit.  
5. Cut the (2) light harness wires (blue, white) in between the flame motor cover and  
the right light socket with wire cutters.  
6. Strip the (2) light harness wire ends (blue, white) on the flame motor cover side.  
7. Cut the (2) light harness wires (blue, white) in between the left and right light sockets  
with wire cutters.  
8. Remove the (2) light socket screws from the rear of the light assembly.  
9. Remove light bulbs.  
10.Remove light sockets by placing hand inside light assembly, grasping light socket  
and pulling light socket until it snaps out of place.  
11.Replace the (2) light sockets.  
12.Wire connect the (4) light socket wires (blue to blue) (white to white) in between the  
left and right light sockets with the supplied wire connectors.  
13.Wire connect the (4) light harness wires (blue to blue) (white to white) in between the  
flame motor cover and the right light socket with the supplied wire connectors.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DFI2309  
If unit was operating prior to servicing allow at least 10 minutes for light bulbs and  
heating element to cool off to avoid accidental burning of skin.  
Disconnect power before attempting any maintenance or cleaning to reduce the risk of  
electric shock or damage to persons.  
TO REPLACE POWER CORD  
1. Remove the trim and firebox from mantel.  
2. Remove the trim from firebox.  
3. Remove the (2) screws located in the front middle of the top and the (2) screws at  
the back of the top.  
4. Disconnect the wiring clips and connections from the heater assembly noting their  
original locations.  
5. Set aside top panel.  
6. Remove the (2) screws located on the top of the side panels and the (2) screws from  
the middle on the back panel.  
7. Remove exhaust panel and set aside.  
8. Remove mirror.  
9. Locate and disconnect the power cord wiring connections noting their original  
locations.  
10.With needle nose pliers grasp the power cord strain relief grommet from inside the  
rear of the back panel and push while twisting to remove.  
11.Pull the power cord out through the hole in the rear of the back panel.  
12.Install the new power cord through the hole in the back panel and connect all of the  
wiring connections in their original locations.  
13.Install the power cord strain relief grommet on the replacement power cord and  
insert into the mounting hole in the rear of the back panel.  
WARNING: Ensure wires do not come in contact with moving parts by securing  
wires in wiring tie wraps.  
14.Reassemble in the reverse order as above.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Conair Trimmer GMT175R User Manual
Cuisinart Water Dispenser WCH 1500A User Manual
Curtis Home Theater System TDVD6048 User Manual
Cypress Computer Hardware CY7C1217H User Manual
Danby Microwave Oven DMW745SS User Manual
Danby Microwave Oven DMW1104BL User Manual
Dixon Lawn Mower 6029FX User Manual
Eagle Electronics SONAR 350 S MAP User Manual
Electro Voice Microphone N D267a User Manual
FEIN Power Tools Drill ASB 18V User Manual