37” HD Ready LCD TV
DGL3704M
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
CONFORMITY AND COMPLIANCE
FCC Compliance Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a residential installation. This device generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this device does cause harmful interference to radio or television
reception (this can be determined by turning, the device off and on), you are encouraged to try to correct
the interference by one or more of the following measures:
*Reorient or relocate the receiving antenna.
*Increase the separation between the equipment and the receiver.
*Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
*Consult the dealer or an experienced radio/TV technician for help.
Caution:
To comply with the limits for an FCC Class B computing device, you should use the shielded signal cord
and power cord supplied with this unit. The Federal Communication Commission warns that changes or
modifications of the unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
Radio Frequency Interference Statement
Warning:
This is a Class B product. In a domestic environment this product may cause radio interference in which
case the user may be required to take adequate measures.
Canadian Doc Notice
For Class B Computing Devices
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus
as set out in the Radio Interference Regulation of the Canadian Department of Communications.
CE MARKING DECLARATION OF CONFORMITY
The LCD display complies with the requirements of related European standards, which include:
z
z
z
Emission: EN 55022, EN 61000-3-2, EN-61000-3-3
Immunity: EN 50082-1
Safety: EN 60950 Low-Voltage Directive (73/23/EEC)
manufactured
under license from BBE Sound, Inc.
is a trademark
of SRS Labs, Inc. WOW technology is
incorporated under license from SRS Labs,
Inc.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Thank you for purchasing the DGL3704 display set. This Flat-Screen LCD can be used
either as a Television or as a computer monitor. With its multiple input options, you can
connect almost any device (e.g. VCR, DVD players and game consoles) to this display.
You can also connect your display to a stereo system with a subwoofer to experience
the ultimate in home entertainment. This Manual has been designed to help you install
and operate your display properly. We would recommend that you read it thoroughly.
Table of contents
Page
Getting Started
Features..………………………………………………………….
Standard Accessories ………………………………................
Controls and Function ………………………………
Remote Control ………………………………………………….
4
4
5
7
Installation
Installing your Display ………………………………………….
Quick Installation ……………………...……..……………….…
8
9
Operation - TV
Basic Operation…………………………………………………...
OSD MENU Setting …………………….…………………………
TV/PC Parameters……..……...……………………………..…..
Audio Settings……………………………………………….….....
Picture-In-Picture………..………………………………….……..
General Settings………………………………………….……..…
Parental Controls …………………..…..………………….……..
10
11
12
13
14
15
17
Other information
Troubleshooting ………………………….……………………....
Supporting Operation Mode ……………….…………………..…
20
21
Introduction
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Start
Features
˙ Supporting resolution of WXGA mode (1920x1080 pixels)
˙ Wide viewing angle
˙ Digital Character Smoothing
˙ Analog TV tuner
˙ Windows 95/98/2000/XP Plug & Play Compliant
˙ Versatile, functional & User friendly OSD
˙ Plug & Play: Conform to the VESA standards and support DDC 2B spec.
Standard Accessories
Unpacking and Checking of the Package Contents
y Before unpacking your LCD Display, prepare a stable, level, and clean surface near
a wall outlet for your LCD Display.
y Set the LCD Display box in an upright position and open from the top of the box
before removing the right/left cushions.
Accessories
1 pc
User’s Manual
1 pc
Remote
Controller
1 pair
Batteries
1 pc
RCA Adapter
1 pc
VGA Cable
1 pc
Power Cord
1 pc
Audio Cable
Power source: (for 37” AU Panel)
- Manufacturer: FSP
- Type: FSP310-4M01
- Rating: 3.5A, AC 100-240V, 50-60Hz
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Front View
Getting Started
Controls and Functions
Operating the monitor
Top Panel Buttons：
LED indicator
Green for operating PC monitor and
TV system. Red when AC Power
switch on or no signal.
① POWER：Press to turn the Display On/Off. (Main Power Switch must be On)
NOTE: The Main Power Switch is located on lower back panel.
② SOURCE：Press to display and cycle the available input sources.
③ MENU：Press to open the OSD menu and make function changes/adjustments.
④ ENTER: Press to select an item, exit a function in the OSD menu or confirm a setting.
⑤,⑥ CHc/d： Press to select a channel or select items in OSD menu.
⑦,⑧ VOLf/e：Press to adjust the volume, select OSD items and adjust the menu items.
• MAIN POWER SWITCH (Rear Panel): Set to on ( – ) to power up unit.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Rear View
Rear Panel Jacks
Side view
Video Component1 Input terminal accepts video signal from a Component Video Source
Y1Cb1Cr1
1
2
3
(INTERLACED only)
Y1Cb1Cr1 Audio
Y2Pb2Pr2
L&R Audio input corresponding with Video Component1
Video Component2 Input terminal accepts video signal from a Component Video Source
(PROGRESSIVE SCAN or INTERLACED)
Y2Pb2Pr2 Audio
S-video
L&R Audio input terminals corresponding with Video Component2
S-Video Input terminal accepts video signal from a S-Video source.
L&R Audio input terminals corresponding with S-Video source.
4
5
6
7
S-video Audio
Sub-woofer
Provides a dedicated Sub output signal to drive an external Powered Subwoofer (optional)
Provides a Video output signal.
Video out
Audio out
8
9
(Video output is available only from; AV1, AV2, AV3 and TV sources)
Provides a Stereo Audio output signal.
(Audio output is available only from; AV1, AV2, AV3, TV sources)
AV 1 in
To connect the AV1 Video source.
10
11
12
13
14
15
16
AV 1 audio in
AV 2 in
To connect the Audio corresponding to AV1 source
To connect the AV2 Video source.
AV 2 audio in
AV 3 audio in
AV 3 in
To connect the Audio corresponding to AV2 source
To connect the Audio Corresponding to AV3 source
To connect the AV3 Video source.
Headphone
Provides L&R Audio output to connect a set of headphones.
Bottom view
1
2
3
4
PC Audio In
ANT
Accepts the Audio signal from your PC or Laptop.
Connect the coaxial cable (75 Ohm) or antenna here.
Connects to D-sub 15 pin analog RGB Video from your PC or Laptop.
Connects to DVI digital video output from your PC or Laptop.
D-sub
DVI for PC
Connect the power cord supplied to this terminal and then turn on the Main Power switch right
next to power cord terminal.
5
AC in
Use Y1Cb1Cr1/Y2Pb2Pr2,
AV, or S-video to connect
the VCR, DVD or the Video
Game.
ANT
Adapter
Connect the cable or antenna
Audio cable connects to PC audio
VGA cable connects to VGA card.
DVI cable connects to DVI card (if DVI cable is available)
Connect the
power supply
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Remote Control
TV Function
POWER
TV
Power On/Off (Standby) after turning On the Main Power Switch.
Switch source to TV mode.
Cycle through input sources: TV Æ VGA Æ DVI Æ S-VIDEO Æ AV1Æ AV2 Æ
AV3 Æ COMPONENT 1Æ COMPONENT 2
Also used for selecting the main source during PIP / PBP mode.
SOURCE
DISPLAY
Number keys
MUTE
Displays the current information.
Selects TV channel directly by the numbers.
Turns the speakers On or Off.
MTS
Selects the TV audio mode; MONO Æ STEREO Æ SAP
Selects the sound enhancement mode: Off-> SRS WOW-> BBE
SOUND
Press once or repetitively to select the preset Color modes available ;
Soft->Standard->Cool->Define
PICTURE
SLEEP
Sets the Timer to turn power off (OFF, 10, 20, 30, 60, 90, 120 Min)
Press to confirm channel selection after entering number directly with
key pad.
(Enter)
(Recall)
MENU
Return to previous channel.
Press to access main OSD menu.
CH d/c
ZOOM
Press to tune-in channels up/down and navigate up/down within menu.
Zoom in or resize screen from 4:3 to Full screen (16:9).
Controls volume Up or Down and navigates menu up/down.
Activate the PIP / PBP function.
VOLe/f
PIP
SOURCE
POSITION
Selects the sub-screen source under PIP / PBP modes.
During PIP/PBP mode, it adjusts the minor screen’s position.
During PIP/PBP mode, swaps picture between main screen and sub-
screen.
SWAP
Freeze either the picture of the screen directly (except VGA mode) or
the “Activated screen” in PIP main screen.
FREEZE
ENTER
C.C.
Press to confirm adjustment of selected item in the OSD menu.
Turn Closed Caption (C.C.) function On / Off. (U.S. area only)
Press to open the V-Chip menu. A password is required to access the
menu. (U.S. area only)
V-CHIP
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing your Display
Step 1. Positioning the display set
Place your Display set on a solid stable surface. To
avoid danger do not expose the display to water, or a
heat source. Do not obstruct the ventilation grid at
rear.
Step 2. Connecting the aerials
ANT
1. Use for connecting the antenna or coaxial cable (75
Ohms) with TV Tuner socket situated at the back of LCD
Display.
① Coaxial F connector / adapter
② Aerial
Step 3. Connecting the power cable
Insert the power cord plug into the wall socket and
then turn on the Main power switch. (located on back)
Step 4. Remote control
6 m (19 feet)
Insert the two AAA/UM4-type batteries
supplied, making sure that the +/ -
polarities are properly aligned.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Quick Installation
If TV is connected to an antenna, you’ll need to set a few important items in the
menu system the first time you turn on your display.
Auto scan:
This part of the setup allows the TV tuner to search for all channels viewable though
your antenna or cable TV system (when there is no cable box connected).
y Press “MENU” on Remote or TV’s front panel to
view OSD “TV PARAMETERS” screen.
y Pressf button 3 times to highlight the fifth item
“CHANNEL SETTINGS”.
y Press “ENTER” to select “SYSTEM”.
y Press ꢀorꢁbutton to select “Antenna/Cable”
then press “MENU”.
y Press ꢁ button to select “AUTO SCAN” and
select “YES” with ꢁbutton to begin the auto
channel search.
(Pressing “MENU” will stop auto scan) Once
Scanning is completed, use the CHꢁ or CHꢀ buttons
to tune-in only receivable channels.
Ch. Edit (Channel Edit):
While in the “CHANNEL SETTINGS” select “CH. EDIT” to add additional receivable
channels and erase unwanted channels during Up/Down tuning.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
Basic Operation
Power On/Off
Press the “POWER” key to turn ON the Display. The power indicator changes from
red to green. When the power is OFF (standby), the power indicator changes from
green to red.
Source select
Press “SOURCE” to select the input signal. Each time the source button is pressed, the
on-screen display will cycle between:
TV
VGA
DVI
S-VIDEO
AV1
AV2
Component2 (Y2Pb2Pr2)
Component1 (Y1Cb1Cr1)
AV3
TV Button
Switch source to TV mode directly without using the source key to select.
Adjusting the volume
Press f on the remote controller to increase the volume.
Press e to decrease the volume.
Channel select
Press c on the remote controller to change to the next viewable channel.
Press d to change to the previous channel or you can select a channel number directly
and press “ ” to confirm.
Menu On/Off
Press “MENU” key to display the OSD main menu On/Off.
Use e/f to select the item on the main menu.
Press “ENTER” to the submenu and pressd/c navigate up/down. Use e/fto adjust
the setting.
Press “MENU” key to escape selection or revert to other selections.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
OSD MENU DESCRIPTION
To access MENU, navigate and make adjustments using; MENU、cCH、dCH、
eVOL、f VOL and ENTER.
y
Pressing “MENU” displays the OSD menu. Use cCH / dCH on the remote
controller to scroll the options on the menu.
y
y
y
y
y
Press “ENTER” button to enter sub menu.
Usee/f to adjust settings.
Press “ENTER” to confirm desired settings.
Press “MENU” after adjustment is made, to revert to the next adjustment.
Press “MENU” to exit the current OSD menu.
Main Menu:
There are seven SUB-MENUS in the main OSD Menu.
1. TV PARAMETERS; 2.PC PARAMETERS; 3.AUDIO SETTINGS; 4.Picture-In-Picture;
5.CHANNEL SETTINGS; 6.PARENTAL CONTROLS; 7.GENERAL SETTINGS.
In TV mode – Press MENU
Use e/f buttons to select the submenu: TV Parameters, Audio Setting, Picture-In-
Picture, Channel Settings, Parental Controls, and General Settings.
Note: In TV mode, “PC Parameters” cannot be selected.
In Video mode (S-VIDEO, AV1 ,AV2, AV3, COMPONENT1(Y1Cb1Cr1) ,
COMPONENT2(Y2Pb2Pr2))
Press “MENU” button, Main menu will be displayed on the screen (see figure above).
Use e/f buttons to select the submenu: TV Parameters, Audio Setting, Picture-In-
Picture, and General Settings.
Note: 1. In this mode, “Channel Settings” cannot be selected.
2. For devices with PROGRESSIVE SCAN 480p, 720p or 1080i output, connect
them to Component-2 jacks to obtain the ideal resolution and picture quality.
In PC mode (DVI, VGA)
Press “MENU” button, Main menu will be displayed on the screen (see figure above).
Use e/f buttons to select the submenu: Audio Settings, Picture-In-Picture and General
Settings.
Note: In this mode, “TV Parameters” and “Channel Settings” cannot be selected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
TV/PC Parameters
TV Parameters
Press “MENU” and make sure the “TV Parameters” is shown on the screen.
Adjusting the TV setting:
y Brightness: Alters the brightness of the image.
y Contrast: Alters the ratio of light to darkness.
y Sharpness: Adjusts the sharpness of the color.
y Saturation: Alters the color saturation.
y Hue: Alters the color intensity.
y Color temp: Adjusts the color temperature of the
picture. Three options are available here: 6500, 7500,
9300, and USERS.
y Format: Two options are available here: Full screen
(16:9) and 4:3.
16:9
4:3
Color Temp.
PC parameters
Adjusting the picture setting:
y Brightness: Alters the brightness of the image.
y Contrast: Alters the variation between light and
darkness.
y Auto: Auto adjusts the position of the image.
y Auto color: Auto adjusts the color balance.
Note: “AUTO COLOR” function is only available in
“VGA” and “Component 2” input sources. By accessing
“ALL RESET” function in “General Settings”, the color
will return to the factory default setting.
Set Image:
y Clock: Adjusts the clock frequency.
y Phase: Adjusts the phase frequency.
y H-Position & V-Position: Adjusts the horizontal and
the vertical position of the image.
y Color Temp.: Adjusts the color temperature of the
picture.
y Format: Two options are available here: Full screen
(16:9) and 4:3.
y
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
Audio Settings
Press “MENU” and make sure the “AUDIO SETTINGS” is displayed on the screen.
ꢀ In TV, Video, and PC modes
Adjusting the audio setting:
y Volume: This will adjust the level of volume.
y Mute: Mutes the sound
y Bass: This will adjust the level of low frequency
content in the sound. (Enabled only when BBE
or SRS WOW feature is off)
y Treble: This will adjust the level of high
frequency content in the sound. (Enabled only
when BBE or SRS WOW feature is off)
y Balance: This will adjust the relative output of
the R/L speakers to obtain the best stereo
reproduction.
MTS (For TV mode only):
y MTS: This will select the TV audio output. Three
options are available: Mono, Stereo, SAP.
y Surround: This will select the available audio
modes for SRS WOW sound effect.
y BBE: This can improve clarity of sound and
speech intelligibility.
Press “MENU” after adjustment is made.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
Picture-In-Picture
PIP function:
The PIP function allows you to watch two screens on the display from two different
sources at the same time. For example; you can watch a TV channel and a component
video source at the same time. See PIP structure chart below.
Press:
PIP
To start the PIP function.
Off->PIP(Small) ->PIP(Medium) ->PIP(Large)-> PBP -> POP
SOURCE
To select the sub screen’s source. (See the PIP structure below)
POSITION To adjust the PIP position.
SWAP
Freeze
To switch the picture of main screen to sub screen.
To freeze the PIP main screen.
[Basic function]
You can control PIP function easily by remote control.
PIP mode
PIP source
PIP position
Swap PIP
PBP
source & swap
POP
Source & swap
PIP size –small PIP size–medium PIP size–large
Freeze the PIP
main screen
Note: 1. M: main screen; S: sub-screen
2. The PIP submenu can be used to control the sub-screen size.
3. The “SOURCE” button selects the sub-screen. Use the “SWAP” or “FREEZE” buttons
to manipulate the main screen.
PIP structure
Main Screen
PIP
TV
AV1
AV2
AV3
S-Video
Component1
Component2
(Y2Pb2Pr2)
y
VGA
DVI
(Y1Cb1Cr1)
TV
y
y
y
y
y
y
y
y
y
y
y
y
AV1
AV2
AV3
y
y
y
y
S-Video
Sub-
Screen
Component1
(Y1Cb1Cr1)
Component2
(Y2Pb2Pr2)
VGA
DVI
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
y
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
General Settings
Press “MENU” and press f to select “GENERAL SETTINGS”.
In TV, Video, and PC modes
Adjusting GENERAL SETTINGS:
y OSD Timeout: Adjusts the OSD elapsed time before
disappearing after the last selection. Press e/f to
increase or decrease the time. Timeout range: 10, 20,
and 30 sec.
y OSD Position: Adjusts the horizontal and vertical
position of the OSD on the screen.
y OSD Language: 4 options available; English, French,
Spanish and T. Chinese. (T. Chinese is disabled depending
on model)
y Display Info. : Shows the Display information on the
screen
y All Reset: Resets to the factory default settings.
y Sleep Timer:
With sleep timer you can set a time period after which the TV automatically switches to
standby. The counter can be set from 120 Min to OFF as follows;
1. Press “MENU” and select “GENERAL SETTINGS”
with f button.
2. Select “Sleep Timer” withd button and press
“ENTER” to access submenus.
3. Use e/f to adjust the settings.
4. Press “ENTER” to confirm the setting.
5. Press “MENU” to exit the current OSD page.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation - TV
General Settings
Deinterlace:
Note: Only available in AV, S-Video, TV1, Component1 input sources.
DCDI: This function produces smooth and natural images
by minimizing staircasing or jaggies.
CCS: This function (CCS) removes “false color” artifacts.
FILM Mode: This function produces artifact-free images by
proper handling of 3:2 and 2:2 pull-down video motion.
Fleshtone: This function can adjust the figure’s skin color to the better
Motion: There are three levels: Small, Medium, and Large. Small Î Slight adjustment;
Medium Î Medium adjustment; Large Î High adjustment.
Note: VGA, DVI, Component2 input sources can not access Deinterlace control.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
" For U.S. area only
Operation - TV
Parental Controls
Closed caption:
To aid the hearing impaired, Closed Caption is a system which displays a text of the
voice dialogue of television programs. This feature uses onscreen text boxes to show
conversation and dialogue while the program is in progress. Usually C.C. 1 is the most
used. C.C. 2 may be used for alternate languages. Text function is usually used for
channel guide, schedules, bulletin board information for Closed Caption programs.
CC Control:
Use remote control:
Press “C.C.” key on the remote control and the closed caption OSD will show on the
screen.
Use menu:
Close Caption setting can also be accessed using the main menu. Press MENU and
select “PARENTAL CONTROLS”.
1. Use d/c to select a C.C. control item and select “ON”.
2. Text boxes will show on the TV screen.
3. You can select either one of the C.C. modes available; C.C. and TEXT.
4. You can also select; BOX and SHADOW as desired.
Close caption programs on
ABC
All items are central time
Close caption programs on
ABC
All items are central time
7:00 top of the morning
12:00 noonday news
7:00 top of the morning
12:00 noonday news
Jean: Nice to meet you.
Mary: Nice to meet
Jean: Nice to meet you.
Mary: Nice to meet
Caption mode - Shadow
example.
Caption mode - BOX
example.
Text mode - BOX example:
The TV screen will be blocked.
Text mode - Shadow example:
The TV screen will be blocked.
Note: 1. Not all the programs, videos and commercials are broadcast with closed caption.
2. Closed Caption function is not available in the Video mode of Component 2.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
" For U.S. area only
Operation - TV
Parental Controls
V-chip:
The V-chip feature automatically blocks TV programs and movies based on violence,
sex, or other content you may believe inappropriate for children. Once you block
programs, you can unblock by entering a password.
Use remote control:
1. Press “V-Chip” key on the remote controller and the V-Chip OSD will be displayed on
the screen.
2. Select the submenu: “Set Password”, “MPAA Rating” & “TV PG Rating” while the V-
Chip Lock is in the “OFF” mode. After setting up the sub menu, you must set the V-
Chip Lock mode to “ON” to enable the V-Chip function.
3. To turn off the V-Chip function, select “OFF” and press “ENTER”. User is requested
to enter the four-digital password before entering V-Chip function. Once the
password is entered correctly, you can access the submenu.
The default password is “1234”.
Use menu:
Press “MENU” key to display and select “Parental Controls” to enter the V-Chip OSD
and get access to its submenu.
MPAA Rating
None Unblock
G
General audiences (All ages
admitted)
PG
Parental guidance suggested.(Some
material may not be suitable for
children)
PG-13 Parents strongly cautioned.(Some
material may be inappropriate for
children under 13.)
R
Restricted. (Under 17 requires
accompanying parent or adult
guardian.
NC-17 No one 17 and under admitted.
X
Adults only. No one under 17
admitted.
V-Chip Lock:
Press “V-Chip Lock” to turn V-chip On and Off.
MPAA rating:
V-chip MPAA (Motion Picture Association of America) uses a rating system applied mainly to
movies. A message is displayed on the screen if any rating categories have been blocked.
1. In the “PARENTAL CONTROLS” menu “V-Chip” sub-menu, select “MPAA” and press
“ENTER” to confirm.
2. Use d/c to enter and block the categories. Select “NONE” to unblock selected.
Ex: The V-Chip will automatically block certain categories that are “more restrictive”. If “R”
category has been blocked, then NC-17 and X will automatically be blocked.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
" For U.S. area only
Operation - TV
Parental Controls
TV PG Rating (Parental Guideline)
USA V-chip Rating System
V-chip reads the program’s age-based rating. If you have blocked the rating, you will
receive a rating message on the screen while you select the blocked program
TV P.G. Rating
None Unblock
TV-Y All children.
none
none
TV-7 Directed to children 7 years and older. The rating of F. Violence can be blocked
TV-G General audience.
none
TV-PG Parental guidance suggested.
TV-14 Parents strongly cautioned.
TV-MA Mature audience only.
The rating of Violence, Sexual Contents, Foul
Language or Suggestive Dialog can be blocked
The rating of Violence, Sexual Contents or Foul
Language can be blocked
- In the “PARENTAL CONTROLS” menu select “V-chip” sub menu.
- Select “TV PG Rating” and confirm press “ENTER” to confirm (the default settings
are all unblocked).
- Use d/c and ENTER select and block the desired categories. Select “NONE” to
unblock selected.
Ex: The V-Chip will automatically block certain categories that are “more restrictive.” If “TV-14”
category has been blocked, then “TV-MA” will automatically be blocked.
Note: V- chip function is not available in the Video mode of Component 2.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Troubleshooting
Perform any adjustments only according to Instruction Manual. If the problem still exists
and you cannot correct the problem, stop using the DISPLAY and contact your dealer or
service center at (866) 333-3384 for assistance.
SYMPTOMS
CHECK ITEMS
Make sure the power cord is firmly plugged in the socket.
Make sure the power switch is turned on.
Make sure the AC socket is OK.
No picture
a) Power indicator
does not light up.
Check if the Remote control if it works or must change its
batteries
Make sure the DISPLAY is ON
No picture
Check if the signal cable is properly connected.
Increase the CONTRAST and/or BRIGHTNESS.
b) Power indicator is
green.
The DISPLAY is on power saving mode, touch the keyboard or
the mouse.
No Picture
c) Power indicator is
red.
Make sure the DISPLAY is ON.
Make sure the signal cable is properly connected.
Unclear picture,
Noise
Make sure the TV signal is received or cables are connected
well.
Make sure the audio cables are properly connected.
Make sure the headphone is not connected.
No Sound
Make sure the “Mute” function is not set.
If picture is received, adjust the TV system setting correctly.
Display is too dark or
too bright.
Lower the contrast and brightness from OSD or input device.
Adjust the image position using H-position or V-position in OSD.
Display is not in the
center.
Check if the power voltage is within the spec.
Display vibration.
Check if the signal cables are properly connected.
After-image remains This is characteristic of liquid crystal, it will not cause malfunction
after turns TV off and disappear after few minutes
Distorted image
Make sure the aspect ratio is set properly.
Check if Proper signal type of “Component” or “RGB” setting is
set.
Purple image
Out of Range
Check if the input signal is acceptable for display.
Green, red, blue,
This is characteristic of liquid crystal. It will not cause
white dots on screen malfunction.
Make sure battery’s power or wrong battery orientation.
Remove the obstacle between remote control and DISPLAY.
Check if one of Key buttons is stuck to cause malfunction.
Notice that the distance from DISPLAY.
Remote control
cannot work
1. User must select the submenu “Set Password” in “Parental
Controls” menu from OSD and enter the master password:
3609. Then you can set a new password for confirmation. All
old settings in “Parental Controls” menu will not be changed
any more.
Lost password
for parental control
2. You can call service center for master password.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Information
Frequency Modes Supported
Supported Timing:
Analog / Digital
Horizontal Frequency Vertical Frequency
Display Mode
31.5 KHz
37.9 KHz
37.5 KHz
43.3 KHz
35.1 KHz
37.9 KHz
48.1 KHz
46.9 KHz
53.7 KHz
48.4 KHz
56.5 KHz
60.0 KHz
68.7 KHz
64.0 KHz
47.7 KHz
67.2 KHz
60 Hz
72 Hz
75 Hz
85 Hz
56 Hz
60 Hz
72 Hz
75 Hz
85 Hz
60 Hz
70 Hz
75 Hz
85 Hz
60 Hz
60 Hz
60 Hz
VGA
640 x 480
800 x 600
1024 x 768
VESA
SVGA
SXGA
1280 x 1024
1366 x768
1920 x1080
WXGA
Note: In PIP function, when selecting VGA or DVI input sources as sub-screen,
SXGA timing can not be supported efficiently.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
|