Desa Water Heater and CVDR30 User Manual

NATURAL GAS LOG

VENTED DECORATIVE APPLIANCES

OWNER’S OPERATION AND INSTALLATION MANUAL

RGA 2-72

APPROVED

RADCO Burner

Models CVSR18,

TESTED AND

LISTED BY

CVSR24, CPVSR18,

CPVSR24, CVDR18,

CVDR24, and CVDR30

WARNING: Improper installa-

tion,adjustment,alteration,ser-

vice,ormaintenancecancause

WARNING:Iftheinformationinthismanualisnot

followed exactly, a fire or explosion may result

causing property damage, personal injury, or

injury or property damage. Re-

fer to this manual for correct

installation and operational

procedures. For assistance or

additional information consult

a qualified installer, service

agency, or the gas supplier.

loss of life.

— Donotstoreorusegasolineorotherflammable

vapors and liquids in the vicinity of this or any

other appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Donottouchanyelectricalswitch;donotuse

any phone in your building.

WARNING: This appliance is

for installation only in a solid-

fuelburningmasonryorUL127

factory-built fireplace, con-

structed of noncombustible

material, and connected to a

working flue. (See page 7 for

minimum flue opening.)

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

• If you cannot reach your gas supplier, call

the fire department.

— Installationandservicemustbeperformedby

a qualified installer, service agency, or the

gas supplier.

WARNING: This is a gas-fired appliance. It uses air (oxygen) from the room in which

it is installed. Provisions for adequate combustion and ventilation air must be

provided. RefertoAirforCombustionandVentilationsectiononpage4ofthismanual.

This appliance may be installed in an aftermarket* manufactured (mobile) home, where not prohibited by

state or local codes.

* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer

Save this manual for future reference.

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

PRODUCT

OPTIONAL

PRODUCT

FEATURES

IDENTIFICATION

ON/OFF SAFETY VALVE/

PILOT KIT AND PROPANE/LP

CONVERSION

Grate Steps

Grate

An optional valve/safety pilot kit with a

piezo ignitor is available for this appliance.

This system requires no matches, batteries,

or other sources to light. You must use this

optional system for LP conversion. See Ac-

cessories, page 20.

REMOTE CONTROL READY

(MILLIVOLT) SAFETY VALVE/

PILOT KIT

Burner

Pan

Burner

Clamp

An optional millivolt valve/safety pilot kit

with a piezo ignitor is available for this

appliance.Thissystemrequiresnomatches,

batteries, or other sources to light. This

systemmaybeconnectedtoawallswitchor

hand-held wireless remote control. See Ac-

cessories, page 20.

Burner Inlet

Fitting

Burner

Manifold

Figure 1 - Product Identification (VVDR24 Shown)

REMOTE CONTROL

ACCESSORIES

Serial Number ________________________________________

Log Set Model ________________________________________

There is an optional hand-held ON/OFF

remote control that can be purchased sepa-

rately for this log set. You must use the

millivolt valve/safety pilot kit to use remote

accessories with this appliance. See Acces-

sories, page 20.

LOCAL CODES

UNPACKING

Install and use log set with care. Follow all

localcodes.Intheabsenceoflocalcodes,use

the latest edition of The National Fuel Gas

CodeANSZ223.1,alsoknownasNFPA54*.

CAUTION: Do not remove the

metal data plates from the burner

pan. The data plates contain im-

portant product information.

*Available from:

1. Remove logs, hearth kit, pan materials,

and hardware from carton.

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

2. Remove all protective packaging ap-

plied to logs and base for shipment.

National Fire Protection Association, Inc.

Batterymarch Park

3. Check all items for any shipping dam-

age. If damaged, promptly inform

dealer where you bought the product.

Quincy, MA 02269

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

Confined and Unconfined Space

PROVIDING ADEQUATE

VENTILATION

AIR FOR

The National Fuel Gas Code (ANS Z223.1,

1992 Section 5.3) defines a confined space

as a space whose volume is less than 50

cubic feet per 1,000 Btu per hour (4.8 m³per

kw) of the aggregate input rating of all

appliances installed in that space and an

unconfined space as a space whose volume

is not less than 50 cubic feet per 1,000 Btu

per hour (4.8 m³per kw) of the aggregate

inputratingofallappliancesinstalledinthat

space. Rooms communicating directly with

the space in which the appliances are in-

stalled*, through openings not furnished

with doors, are considered a part of the

unconfined space.

COMBUSTION AND

VENTILATION

The following are excerpts from National

Fuel Gas Code. NFPA 54/ANS Z223.1, Sec-

tion 5.3, Air for Combustion and Ventila-

tion.

WARNING: This appliance

shall not be installed in a con-

fined space or unusually tight

construction unless provisions

are provided for adequate com-

bustion and ventilation air. Read

the following instructions to in-

sure proper fresh air for this and

other fuel-burning appliances in

your home.

All spaces in homes fall into one of the three

following ventilation classifications:

1. Unusually Tight Construction

2. Unconfined Space

3. Confined Space

The information on pages 4 through 6 will

help you classify your space and provide

adequate ventilation.

Today’s homes are built more energy effi-

cient than ever. New materials, increased

This log set shall not be installed in a con-

fined space or unusually tight construction

unless provisions are provided for adequate

combustion and ventilation air.

Unusually Tight Construction

insulation, and new construction methods The air that leaks around doors and win-

helpreduceheatlossinhomes.Homeowners dows may provide enough fresh air for

weather strip and caulk around windows and combustion and ventilation. However, in

doorstokeepthecoldairoutandthewarmair buildings of unusually tight construction,

in. During heating months, home owners you must provide additional fresh air.

* Adjoining rooms are communicating only

iftherearedoorlesspassagewaysorventila-

tion grills between them.

want their homes as airtight as possible.

Unusually tight construction is de-

While it is good to make your home energy fined as construction where:

efficient, your home needs to breathe. Fresh

air must enter your home. All fuel-burning

appliances need fresh air for proper com-

bustion and ventilation.

a. walls and ceilings exposed to the

outside atmosphere have a con-

tinuous water vapor retarder with

a rating of one perm (6x10^-11kg

per pa-sec-m²) or less with open-

ings gasketed or sealed and

Exhaustfans, fireplaces, clothesdryers, and

fuel burning appliances draw air from the

house to operate. You must provide ad-

equate fresh air for these appliances. This

will insure proper venting of vented fuel-

burning appliances.

b. weather stripping has been

added on openable windows and

doors and

c. caulking or sealants are applied

to areas such as joints around

window and door frames, be-

tween sole plates and floors, be-

tween wall-ceiling joints, be-

tween wall panels, at penetra-

tions for plumbing, electrical, and

gas lines, and at other openings.

If your home meets all of the three

criteria above, you must provide ad-

ditional fresh air. See Ventilation Air

From Outdoors, page 6.

If your home does not meet all of the

three criteria above, proceed to De-

terminingFresh-AirFlowForLogSet

Location, page 5.

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

AIR FOR

COMBUSTION AND

VENTILATION

Continued

DETERMINING FRESH-AIR FLOW FOR APPLIANCE LOCATION

Determining if You Have a Confined or Unconfined Space

Use this work sheet to determine if you have a confined or unconfined space.

Space: Includes the room in which you will install appliance plus any adjoining rooms with doorless passageways or ventilation grills

between the rooms.

1. Determine the volume of the space (length x width x height).

Length x Width x Height = _________________cu. ft. (volume of space)

Example: Space size 20 ft. (length) x 16 ft. (width) x 8 ft. (ceiling height) = 2560 cu. ft. (volume of space)

If additional ventilation to adjoining room is supplied with grills or openings, add the volume of these rooms to the total volume of

the space.

2. Divide the space volume by 50 cubic feet to determine the maximum Btu/Hr the space can support.

_____________ (volume of space) ÷ 50 cu. ft. = (maximum Btu/Hr the space can support)

Example: 2560 cu. ft. (volume of space) ÷ 50 cu. ft. = 51.2 or 51,200 (maximum Btu/Hr the space can support)

3. Add the Btu/Hr of all fuel burning appliances in the space.

Gas fireplace logs

Gas water heater*

Gas furnace

Vented gas heater

Vent-free heater

_____________ Btu/Hr

Example:

Gas water heater

Gas fireplace logs + 55,000 Btu/Hr

Total 95,000 Btu/Hr

40,000 Btu/Hr

Other gas appliances* + _____________ Btu/Hr

Total = _____________ Btu/Hr

* Do not include direct-vent gas appliances. Direct-vent draws combustion air from the outdoors and vents to the outdoors.

4. Compare the maximum Btu/Hr the space can support with the actual amount of Btu/Hr used.

_____________ Btu/Hr (maximum the space can support)

_____________ Btu/Hr (actual amount of Btu/Hr used)

Example: 51,200 Btu/Hr (maximum the space can support)

95,000 Btu/Hr (actual amount of Btu/Hr used)

The space in the above example is a confined space because the actual Btu/Hr used is more than the maximum Btu/Hr the space cansupport.

You must provide additional fresh air. Your options are as follows:

A. Rework worksheet, adding the space of an adjoining room. If the extra space provides an unconfined space, remove door to adjoin-

ing room or add ventilation grills between rooms. See Ventilation Air From Inside Building, page 6.

B. Vent room directly to the outdoors. See Ventilation Air From Outdoors, page 6.

C. Install a lower Btu/Hr heater, if lower Btu/Hr size makes room unconfined.

If the actual Btu/Hr used is less than the maximum Btu/Hr the space can support, the space is an unconfined space. You will need no

additional fresh air ventilation.

WARNING: If the area in which the appliance may be operated is smaller than that defined as an unconfined

spaceorifthebuildingisofunusuallytightconstruction, provideadequatecombustionandventilationairbyone

of the methods described in the National Fuel Gas Code, ANS Z223.1, 1992, Section 5.3 or applicable local codes.

Continued

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

AIR FOR

12"

COMBUSTION AND

VENTILATION

Ventilation

Continued

Ventilation Grills

Into Adjoining Room,

Option 2

Grills

Into Adjoining

Room,

VENTILATION AIR

Remove

Door into

Adjoining

Room,

Option

Ventilation Air From Inside

Building

Option 1

Thisfreshairwouldcomefromanadjoining

unconfined space. When ventilating to an

adjoining unconfined space, you must pro-

vide two permanent openings: one within

12" of the ceiling and one within 12" of the

floor on the wall connecting the two spaces

(see options 1 and 2, Figure 2). You can also

remove door into adjoining room (see op-

tion 3, Figure 2). Follow the National Fuel

Gas Code NFPA 54/ANS Z223.1, Section

5.3, Air for Combustion and Ventilation for

required size of ventilation grills or ducts.

12"

Figure 2 - Ventilation Air from Inside Building

WARNING: Rework work-

sheet, adding the space of the

adjoining unconfined space. The

combined spaces must have

enough fresh air to supply all

appliances in both spaces.

Ventilated

Attic

Outlet

Air

Outlet

Air

To Attic

Ventilation Air From Outdoors

Provide extra fresh air by using ventilation

grills or ducts. You must provide two per-

manent openings: one within 12" of the

ceiling and one within 12" of the floor.

Connect these items directly to the outdoors

orspacesopentotheoutdoors.Thesespaces

include attics and crawl spaces.

Crawl

Space

Inlet

Air

IMPORTANT: Do not provide openings for

inlet or outlet air into attic if attic has a

thermostat-controlledpowervent.Heatedair

enteringtheatticwillactivatethepowervent.

Ventilated

Crawl Space

Inlet Air

Figure 3 - Ventilation Air from Outdoors

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

Btu Input

Natural Gas

Btu Input

Propane Gas

Minimum

Vent Opening

INSTALLATION

MODEL

DESCRIPTION

CVSR18

18" Single Burner

50,000

60,000

55,000

65,000

70,000

40,000

50,000

45,000

55,000

60,000

8" dia.

CAUTION: Do not remove

the metal data plates attached

totheburnerpan. Thedataplates

contain important warranty in-

formation.

CPVSR18 18" Single Burner

CVSR24 24" Single Burner

CPVSR24 24" Single Burner

CVDR18

CVDR24

CVDR30

18" Dual Burner

24" Dual Burner

30" Dual Burner

WARNING: Before installing

in a solid fuel burning fireplace,

thechimneyflueandfireboxmust

be cleaned of soot, creosote,

ashes and loose paint by a quali-

fied chimney cleaner. Creosote

will ignite if highly heated. A dirty

chimney flue may create and dis-

tribute soot within the house. In-

spect chimney flue for damage.

MINIMUM FIREBOX SIZES

LOG FRONT BACK

SIZE WIDTH* WIDTH** DEPTH HEIGHT

18"

24"

30"

28"

29 ³/4"

36"

16"

17"

27"

14"

15 ¹/2"

18"

NOTICE:Installation,service,and

repair of this appliance must be

performedbyaqualifiedinstaller,

service agency, company or gas

supplier experienced with this

type of gas appliance. Only fac-

toryauthorizedcomponentslisted

intheseinstructionsmaybeused

in accordance with the

manufacturer’s instructions and

all codes and requirements of the

authorityhavingjurisdiction. Any

modifications to this kit, or use of

unauthorized components or ac-

cessory items will void the

manufacturer’swarranty,andmay

result in a hazardous condition.

*Add 6" if safety valve/pilot is used

**At depth indicated

BURNER ORIFICE

FUEL INLET PRESSURE

SPECIFICATIONS ("W.C.)

LOG NATURAL PROPANE/LP

SIZE IN. NUM. IN. NUM.

Min.

5.5

Max.

10.5

18" .1285

24" .144

30" .154

.076

.086

.089

Figure 4 - Technical Information Charts

CHECK GAS TYPE

VENTING SPECIFICATIONS

FOR INSTALLATION

Useonlynaturalgas. Ifyourgassupplyisnot

natural gas, you must install ON/OFF Safety

Valve/Pilot Kit (see Accessories, page 20).

Call dealer where you bought log set.

Thefireplacechimneyflueandventmustbe

drafting properly. To check the vent for

proper drafting: Light a tightly rolled news-

paper on one end and place it at the inside

front edge of the fireplace. Observe the

smoke and be sure the vent is properly

drawing it up the chimney. If the smoke

spillsoutintotheroom,extinguishtheflame

and remove any obstruction until proper

venting is achieved.

FLUE OPENING

SPECIFICATIONS

If the fireplace does not have a gas supply

shut-off valve, one must be installed.

Note: This vented appliance must be in-

stalled only in a solid-fuel burning fireplace

with a working flue and constructed of non-

combustible material.

The charts in Figure 4 indicate technical

information regarding the installation of

your gas log set. Please make sure that all of

the specifications shown are applicable be-

fore installation is attempted.

The chimney flue must remain open a mini-

mum of 3" at all times during the operation

of this log set.

The fireplace must include a working flue

andventingsystemwiththeminimumopen-

ings shown in the Figure 4.

Continued

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

CHECKING GAS

CONNECTIONS

INSTALLATION

CAUTION: Use only new,

black iron or steel pipe. Inter-

nally-tinned copper tubing may

be used in certain areas. Check

yourlocalcodes. Usepipeof1/2"

diameter or greater to allow

proper gas volume to log set. If

pipe is too small, undue loss of

pressure will occur.

Continued

INSTALLING DAMPER

CLAMP

WARNING: Test all gas pip-

ing and connections for leaks

after installing or servicing. Cor-

rect all leaks at once.

Secure the damper stop clamp provided to

the leading edge of the damper as shown in

Figure5. Ifforanyreasonthisclampdoesn't

work on your fireplace, another suitable

clamp or permanent stop must be installed,

orthedamperblademustbecutorremoved.

WARNING: Never use an

open flame to check for a leak.

Apply a mixture of liquid soap

and water to all joints. Bubbles

forming show a leak. Correct all

leaks at once.

Installation must include a manual shutoff

valve, union, and plugged 1/8" NPT tap.

Locate NPT tap within reach for test gauge

hook up. NPT tap must be upstream from

log set (see Figure 6).

Damper Clamp

Apply pipe joint sealant lightly to male

threads. This will prevent excess sealant

from going into pipe. Excess sealant in pipe

could result in a clogged burner injector.

Pressure Testing Gas Supply

Piping System

Damper

TestPressuresInExcessOf1/2PSIG

1. Disconnect log set and its individual

manual shutoff valve from gas supply

piping system.

CAUTION:Usepipejointseal-

ant that is resistant to liquid pe-

troleum (LP) gas.

Manufactured

Fireplace

2. Cap off open end of gas pipe where

manual shutoff valve was connected.

Masonry Fireplace

Installsedimenttrapinsupplylineasshown

in Figure 6. Locate sediment trap where it is

within reach for cleaning. Locate sediment

trap where trapped matter is not likely to

freeze. A sediment trap traps moisture and

contaminants. This keeps them from going

into log set controls. If sediment trap is not

installed or is installed wrong, log set may

not run properly.

3. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

Damper

Clamp

4. Check all joints of gas supply piping

system. Apply mixture of liquid soap

and water to gas joints. Bubbles form-

ing show a leak.

Damper

Figure 5 - Attaching Damper Clamp

5. Correct all leaks at once.

6. Reconnect log set and manual shutoff

valve to gas supply. Check reconnected

fittings for leaks.

CONNECTING TO GAS

SUPPLY

Approved Flexible Gas Hose

(if allowed by local codes)

WARNING: A qualified ser-

vicepersonmustconnectlogset

to gas supply. Follow all local

codes.

A.G.A. Design-Certified

Manual Shutoff Valve

With 1/8" NPT Tap*

Installation Items Needed

Before installing log set, make sure you

have the items listed below.

3" Minimum

• piping (check local codes)

• sealant (resistant to LP gas)

• manual shutoff valve

• test gauge connection

• adjustable (crescent) wrench or pliers

• sediment trap

From Gas Meter (5" W.C.**

to 10.5" W.C. Pressure)

Cap

Pipe Nipple Tee Joint

Sediment Trap

Figure 9 - Gas Connection

* Purchase the optional A.G.A. design-certified manual shutoff valve from your dealer. See

• tee joint

Accessories, page 20.

• pipe wrench

** Minimum inlet pressure for purpose of input adjustment.

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

3. Unscrew burner inlet fitting from 4. Install the gas connector tube to the gas

INSTALLATION

burner manifold (see Figure 9).

supply fitting. Carefully shape tube to

Continued

attach to adapter fitting.

4. Place burner manifold in pan with

threaded opening facing open knock-

out plug.

TestPressuresEqualToorLessThan

1/2 PSIG

Gas Connector

Tube

5. Using thread sealant (resistant to the

action of propane/LP gas) on larger

end of fitting, screw the burner inlet

fitting through hole and into burner

manifold. Tighten using a wrench. If

using propane/LP gas, see Propane/LP

Gas Conversion, page 10.

1. Close manual shutoff valve (see Fig-

ure 7).

2. Pressurize supply piping system by either

using compressed air or opening main gas

valve located on or near gas meter.

3. Check all joints from gas meter to manual

shutoff valve (see Figure 7).Apply mix-

ture of liquid soap and water to gas joints.

Bubbles forming show a leak.

Burner Pan

Assembly (Facing

Front of Fireplace)

Adapter

Fitting

6. Using burner clamp, screw, and nut pro-

vided, assemble clamp to pan (“U” style

burners only). This will hold the burner

manifold in place.

Figure 10 - Connecting Gas to Appliance

4. Correct all leaks at once.

7. If using optional GA9050 series kit, go

to Optional GA9050 Series On/Off Safety

Valve/Pilot Kit section for installation in-

Manual Shutoff Valve

OPTIONAL GA9050 SERIES

ON/OFF SAFETY VALVE/

structions. If using optional GA9150 se- PILOT KIT ASSEMBLY

ries kit, follow instructions included with

For additional convenience and safety, or

kit for installation and operation.

Gas Meter

forpropane/LPconversion,anoptionalON/

Nut

OFF safety valve/pilot kit is available. See

Accessories, page 20.

Burner

Manifold

Burner

Clamp

WARNING: You must use a

ON/OFF safety valve/pilot kit for

propane/LP conversion.

Figure 7 - Checking Gas Joints

HEARTH KIT ASSEMBLY

AND INSTALLATION

Natural Gas Installation

1. Thread the gas control valve onto the

burner inlet fitting (see Figure 11). Use

thread sealant on the male threads of

the burner inlet fitting. Hold the burner

inlet fitting with a wrench to prevent

overtightening the connection to the

burner. Make sure the control rod is

facing the front (see Figure 11).

Kit Assembly

Note: The following instructions apply to

both standard single bar burners, as well as

dualflame“U”styleburners. Besureallpipe

threaded connections are tight, and have

thread compound to prevent leaks.

Burner

Pan

Screw

Figure 9 - Installing Burner

Burner Inlet

Fitting

1. Determine which side the gas line will

be coming into the fireplace.

Installation and Gas Connection

2. Using a hammer and screw driver, re-

move knock-out plug from the side of

the pan that corresponds to the gas line

(see Figure 8).

1. Place the burner pan assembly in the

center of the fireplace floor. Make sure

the front of pan faces forward.

Gas

Control

Valve

2. Thread the gas supply fitting to the

fireplace gas supply pipe. Use thread

sealant.

Knock-Out Plugs

3. Install adapter fitting onto the burner

inlet fitting using thread sealant on

male threads of burner inlet fitting

(see Figure 10).

Burner Pan

Assembly

Burner Inlet

Fitting

Control Rod

Burner Pan

Assembly (Facing

Figure 11 - Installing Gas Control Valve

Front of Fireplace)

Figure 8 - Knock-Out Plug Locations

Continued

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

Gas

Connector

Tube

2. Be sure to use the correct orifice for your

appliance. The hardware kit included

with this appliance contains two orifices

with a cone-like shape. If you have an

18" set, the orifice for the burner inlet

fitting is red; for a 30" set, it is black. If

you have a 24" log set, the orifice is al-

ready installed inside the fitting.

INSTALLATION

Continued

2. Attach the pilot gas line to the pilot out-

let of the gas control valve and tighten.

Connect the thermocouple to the rear of

the gas control valve. See Figure 12. Do

not overtighten. If using propane/LP gas,

see Changing Pilot Orifice, page 11.

3. For an 18" or 30" set, use a 10mm

socket or nut driver to remove the ori-

fice from the propane/LP burner inlet

fitting. Choose the correct orifice for

your log set size and install in place of

the orifice you just removed.

3. Install the inlet fitting into the inlet

opening of the gas control valve (see

Figure 13). Use thread sealant on the

male pipe threads.

Inlet

Opening

Gas Control

Valve

Gas Inlet

Fitting

Figure 13 - Installing Inlet Fitting and Gas

Connector Tube

4. Place the burner pan assembly in the

center of the fireplace floor. Make sure

the front of pan faces forward.

4. Using thread sealant (resistant to the

action of propane/LP gas) on larger end

of fitting, screw the burner inlet fitting

through hole and into burner manifold.

Tighten using a wrench.

Thermocouple

Screw

5. Thread the gas supply fitting to the fire-

place gas supply pipe. Adjust to most

convenient position.

Pilot

5 . Follow steps 1 through 12 under Natu-

ral Gas Installation, pages 9 and 10.

6. Install the gas connector tube to the gas

supply fitting. Carefully shape tube to

attach to adapter fitting.

Ignitor

Injector for

Propane/LP

Gas

7. Test for leaks following instructions

Natural Gas

under Testing Burner for Leaks, page 11.

8. Retighten and adjust the location of the

gas control as necessary. The gas con-

trol should be level, with the control rod

to the front.

NATURAL

GAS

FITTING

PROPANE/

LP GAS

FITTING

9. Install cover to burner pan using screws

provided.

Figure 15 - Burner Inlet Fittings with

Injectors

Valve Cover

10. Install thermocouple, pilot, and ignitor

onto valve cover as shown in Figure 14.

Use the provided screws.

Piezo Ignitor

Control

Burner Inlet

Fitting for

Natural Gas

Control

Rod

11. Push the control rod extension onto the

“D” shaped control rod through the cen-

ter hole in the cover.

Knob

Extension

Figure14-InstallingCover,ControlKnob,

and Piezo Ignitor

12. Install the position decal and control

knob making sure to align the marks

with the correct stop positions of the

gas control. Pilot position will allow the

knob to push in about 1/2". Align the

decals in the pilot position.

Propane/LP Gas Conversion

To convert to propane/LP gas, the burner

inlet fitting and pilot orifice must be re-

placed.Thepropane/LPburnerinletfittingis

supplied with the orifice installed for a 24"

log set. If you have an 18" or 30" set, you

must change this orifice also. See Figure 1,

page 3 for product identification.

Figure 16 - Remove Burner Inlet Fitting

Changing Pilot Orifice

Thermocouple and Line

The pilot is provided with a natural gas

orifice installed. For propane/LP gas you

must remove it and replace it with an pro-

pane/LP orifice. The hardware kit contains

an propane/LP orifice with a red stripe for

converting the pilot.

Pilot and Line

Burner Inlet Fitting

1. Remove the burner inlet fitting from the

burner pan assembly. DO NOT remove

the orifice from this fitting. The pro-

pane/LP burner inlet fitting is included

in the hardware kit (see Figure 15).

Gas Control Valve

1. Gently loosen and remove the pilot

line connection from the bracket (see

Figure 17, page 11).

Figure 12 - Gas Control Valve with Ther-

mocouple and Pilot

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

ADDING PAN MATERIAL

INSTALLATION

1. Open the bag ofAsh Bed Material (ver-

miculite) and spread it evenly across the

burner pan to the top. You may over-

flow the front and sides of the pan to

cover the entire pan and connecting

hardware. Do not cover GA9050 series

or GA9150 series valve.

Continued

2. Replace the injector (see Figure 17)

with the propane/LP pilot injector with

the red stripe.

3. Replace and tighten the pilot line to the

bracket.

2. Open the glowing embers and evenly

cover the Ash Bed Material (vermicu-

lite) in the burner pan.

4. Continue with step 3 under Natural Gas

Installation, page 10.

Oxford Oak Logs

INSTALLING THE GRATE

AND LOGS

1. Place the grate over the burner pan

where the two outer horizontal supports

on the grate fit into the two pan posi-

tioning notches in the rear vertical edge

of the pan.

Pilot

Injector

2. Slide the two rear log grate steps over

the two outer horizontal supports on the

grate as shown in Figure 18 (Not In-

cluded with Oxford Oak Models).

Figure 17 - Installing Propane/LP Pilot

Orifice

TESTING BURNER FOR

LEAKS

1. Generously apply soapy solution to all

connections.

3. Place the back log on the grate onto the

grate steps (see Figure 19). If assembling

Oxford Oak models, place log on the

back of the grate bars (see Figure 19).

Amherst Oak Logs

4. Place the front log(s) on the grate and

slide forward against the front bars on

the grate (see Figure 19).

WARNING: Never check for

gas leaks with open flame.

5. Place the smaller top logs onto the bot-

tom logs (see Figure 20). Leave as

much open space between logs as pos-

sible to minimize flame impingement

and sooting. Note: Logs may chip if

they are handled roughly or if hit to-

gether while being placed.

2. Light the burner with the shut-off valve

no more than half open and holding a

match slightly in front of the pan (see

Lighting Instructions, page 12).

3. Inspect all connections for bubbles, raw

gas odor, or flame from any area other

than the burner (leaks). If leaks are de-

tected, shut off the gas valve immedi-

ately. Tighten, or reassemble the loose

connection(s) using pipe joint com-

pound until burner system is leak free.

Berkshire Split Oak Logs

Grate Steps

Grate

Figure 19 - Installing Front and Back Logs

(Number and style of your logs may vary)

4. When the burner is tested and leak free,

observe the individual tongues of flame

on the burner. Note: The burner design

includes more ports on the outside of the

bar. Make sure that all ports are clear

and producing flame evenly across the

burner. If any ports appear blocked, clear

them by removing the burner manifold

and reaming the ports with a modified

paper clip or other suitable tool.

Figure 18 - Installing Grate (Pan Material

Not Shown)

5. When finished testing, turn the gas shut-

off valve OFF to extinguish all flames.

Figure 20 - Placement of Top Logs

(Berkshire Split Oak Logs Shown)

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

5. Turn control knob counterclockwise

GAS SHUT-OFF

VALVE OPERATION

OPERATING

to the PILOT position and

press in. Keep control knob pressed

in for five (5) seconds.

Note: You may be running this log

set for the first time after hooking up

to gas supply. If so, the control knob

may need to be pressed in for 30 sec-

onds. This will allow air to bleed from

the gas system.

• If control knob does not pop up

when released, contact a qualified

service person or gas supplier for

repairs.

APPLIANCE

Flame Adjustment

1. Adjust the flame ON/OFF by turn-

ing the gas shut-off valve counter-

FOR YOUR SAFETY

READ BEFORE

LIGHTING

clockwise

wise

to open or clock-

to close, as necessary.

WARNING: Keep flue open

when operating unit.

Shutting Off Appliance

1. Turn gas shut-off valve clockwise

to the OFF position.

WARNING: If you do not fol-

low these instructions exactly, a

fireorexplosionmayresultcaus-

ing property damage, personal

injury or loss of life.

CURING LOGS

6. With control knob pressed in, push

down and release ignitor button. This

will light pilot. The pilot is attached

to the rear of the front burner. If

needed, keep pressing ignitor button

until pilot lights.

During the 2-3 hour appliance break-in

period, you may detect an odor from the

appliance as the various paints and com-

pounds used in the manufacturing of this

log set cure. This is a normal and tempo-

rary situation that is not cause for alarm.

However, you may want to provide extra

ventilation to the room during this time.

To ensure proper curing of the logs:

• Ignite a 2" flame and maintain it for 1

hour.

• Burn the logs in consecutive 1 hour pe-

riods raising the flame an additional

2" to full flame height for a total of

three hours.

BEFORE LIGHTING smell all around

the appliance area for gas. Be sure to

smell next to the floor because some gas is

heavier than air and will settle on the

floor.

Note: If pilot does not stay lit, con-

tact a qualified service person or gas

supplier for repairs. Until repairs are

made, light pilot with match.

7. Keep control knob pressed in for 30

seconds after lighting pilot. After 30

seconds, release control knob.

Note: If pilot goes out, repeat steps

3 through 7.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do

not use any phone in your building.

• Immediately call your gas supplier

from a neighbor’s phone. Follow the

gas supplier’s instructions.

8. Turn control knob counterclockwise

to the ON position. Burner

should light. If burner does not light,

call a qualified service person.

• If you cannot reach your gas supplier,

call the fire department.

OPERATING

INSTRUCTIONS FOR

GA9000

Control Knob

Ignitor

Pilot

LIGHTING

INSTRUCTIONS

Note:OperationinstructionsforGA9100

Remote Ready Valve/Pilot Kit will be

included with the Kit.

OFF

FROM "PILOT" POSITION

SLIGHT PUSH TO

TURN OFF

Off

1. STOP! Read the safety information,

above.

2. Turn the gas shut-off valve to OFF.

3. Wait five (5) minutes to clear out any

gas. If you then smell gas STOP! Fol-

low the safety information above. If

you don't smell gas, go on to the next

step.

PULL PUSH

1. STOP! Read the safety information,

column one this page.

2. Make sure manual shutoff valve is

fully open.

Figure 21 - Ignitor and Control Knob

3. Press in and turn control knob clock-

wise

to the OFF position.

4. Wait five (5) minutes to clear out any

gas. Then smell for gas around log set

and near floor. If you smell gas,

STOP! See Safety information, page 2

and Air For Combustion And Ventila-

tion, pages 4 through 6. If you don’t

smell gas, go to the next step.

Thermo-

couple

4. Light a match and lay it on top of

the pan material about 2" from the

end of the supply side of the pan

5. Slowly turn the gas shut-off valve ON

until the burner ignites. If the burner

doesn’t ignite within 10 seconds with

the match burning, turn the shut-off

valve OFF and repeat steps 1 through

4 again.

Pilot

Figure 22 - Thermocouple and Pilot

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

OPERATING

APPLIANCE

Continued

TO TURN OFF GAS

TO APPLIANCE

Shutting Off Appliance

1. Turn control knob clockwise

to the PILOT position.

2. Press in and turn control clockwise

to the OFF position.

Shutting Off Burner Only (pilot

stays lit)

Turn control knob clockwise

the PILOT position.

TROUBLESHOOTING

WARNING: Turn off log set

CAUTION: Never use a wire,

needle, or similar object to clean

ODS/pilot.ThiscandamageODS/

pilot unit.

Note: For additional help, visit DESA

International’stechnicalservicewebsite

at www.desatech.com.

andletcoolbeforeservicing.Only

aqualifiedservicepersonshould

service and repair log set.

Note:Alltroubleshootingitemsarelistedin

order of operation.

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Log set is smoking/sooting excessively

(Note: It is natural and unavoidable for

vented gas log sets to produce moderate

levels of carbon (soot) where flames

contact the logs. This is especially true

with propane/LP gas.)

1. Poor fuel quality

1. Contact local natural or propane/LP gas

company

2. Fireplace venting system not drafting 2. Adjust damper wide open and/or have

properly

fireplace and venting professionally

cleaned and checked

3. Excessive flame impingement or block- 3. Separate the logs to allow more flame

age

passage

4. Improper fuel/air mixture

4. Remove any foreign items from the

flame pattern and/or check for proper

orifice sizing

5. Excessive gas supply/pressure

5. Preheat flue in very cold weather

Burner is excessively noisy

(Note: The movement and combustion of

gas will create low, unavoidable levels of

noise.)

1. Passage of air/gas across irregular sur- 1. Relieve any tight bends or kinks in gas

faces

supply line

Burner flame is too low or too high

1. Incorrect gas supply or pressure

1. Check for proper gas supply pressure

2. Blocked burner orifice or burner mani- 2. Free burner orifice and manifold ports

fold ports

3. Improper burner orifice size

of any burrs, paint, or other blockage

3. Verify proper burner orifice sizing (see

Figure 4, page 7)

www.desatech.com

Continued

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

TROUBLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in

your building.

• Immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier’s instructions.

• Ifyoucannotreachyourgassupplier,callthefiredepartment.

IMPORTANT: Operating log set where impurities in air exist may create odors.

Cleaningsupplies,paint,paintremover,cigarettesmoke,cementsandglues,new

carpet or textiles, etc., create fumes. These fumes may mix with combustion air

and create odors. These odors will disappear over time.

POSSIBLE CAUSE

OBSERVED PROBLEM

REMEDY

1. Metal expanding while heating or con-

tracting while cooling

Log Set produces a clicking/ticking noise

just after burner is lit or shut off

1. This is common with most log sets. If

noise is excessive, contact qualified ser-

vice person

1. Log Set burning vapors from paint, hair

spray, glues, cleaners, chemicals, new

carpet, etc. (See IMPORTANT state-

ment above)

Log Set produces unwanted odors

1. Open flue to maximum. Stop using odor

causing products while log set is running

2. Gas leak. SeeWarning statement at

top of page

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 8)

1. Gas leak. SeeWarning statement at

top of page

2. Control valve defective

Gas odor even when control knob is in OFF

position

1. Locate and correct all leaks (see Check-

ing Gas Connections, page 8)

2. Replace control valve

1. Gas leak. SeeWarning statement at

Gas odor during combustion

2. Locate and correct all leaks (see Check-

ing Gas Connections, page 8)

top of page

www.desatech.com

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

TROUBLESHOOTING

Continued

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

When ignitor button is pressed, there is no 1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable

spark at pilot (GA9000 Only)

tor cable

2. Ignitor cable pinched or wet

2. Free ignitor cable if pinched by any

metal or tubing. Keep ignitor cable dry

3. Scrape away paint on bracket for better

contact with ground on piezo ignitor

4. Replace ignitor cable

3. Bad ground on piezo ignitor

4. Broken ignitor cable

5. Bad piezo ignitor

6. Ignitor electrode broken

7. Ignitor electrode positioned wrong

5. Replace piezo ignitor

6. Replace electrode

7. Reposition electrode

When ignitor button is pressed, there is 1. Gas supply turned off or manual shutoff 1. Turn on gas supply or open manual

sparkatpilotbutnoignition(GA9000Only)

valve closed

2. Control knob not in PILOT position

shutoff valve

2. Turn control knob to PILOT position

3. Control knob not pressed in while in 3. Press in control knob while in PILOT

PILOT position

4. Air in gas lines when installed

position

4. Continue holding down control knob.

Repeat igniting operation until air is re-

moved

5. Pilot adjustment screw closed

6. Pilot is clogged

5. Adjust pilot flame for approximately

2" blue flame

6. Clean pilot (see Cleaning and Mainte-

nance, page 20) or replace pilot assembly

7. Replace gas control

7. Low gas pressure

Pilot lights but flame goes out when control 1. Control knob not fully pressed in

1. Press in control knob fully

knob is released (GA9000 Only)

2. Control knob not pressed in long enough 2. After pilot lights, keep control knob

pressed in 30 seconds

3. Manual shutoff valve not fully open

3. Fully open manual shut-off valve

4. Pilot flame not touching thermocouple, 4. A) Contact local natural gas company

which allows thermocouple to cool,

causing pilot flame to go out. This prob-

lem could be caused by one or both of

the following:

B) Clean pilot (see Cleaning and Mainte-

nance, page 20) or replace pilot assembly

A) Low gas pressure

B) Dirty or partially clogged pilot

5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten

trol valve

6. Thermocouple damaged

7. Control valve damaged

1/4 turn more

6. Replace thermocouple

7. Replace control valve

Burner does not light after pilot is lit 1. Burner orifice clogged

1. Clean burner orifice

2. Contact local natural or propane/LP gas

company

(GA9000 Only)

2. Inlet gas pressure is too low

3. Burner orifice diameter is too small

3. Replace burner orifice

4. Thermocouple leads disconnected or im- 4. Reconnect leads

properly connected

Delayed ignition burner (GA9000 Only)

1. Pilot flame needs adjusting

2. Wrong pilot orifice

1. Adjust pilot flame for approximately

2" blue flame

2. Replace pilot orifice set

www.desatech.com

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

ILLUSTRATED

PARTS

BREAKDOWN

RADCO BURNER

MODELS CVSR18,

CVSR24, CPVSR18,

AND CPVSR24

Oxford Round Oak Logs

Amherst Round Oak Logs

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

This list contains replaceable parts used in your log set. When ordering parts, follow the

instructions listed under Replacement Parts on page 20 of this manual.

PARTS LIST

RADCO BURNER

MODELS CVSR18,

CVSR24, CPVSR18,

AND CPVSR24

KEY PART NUMBER FOR

NO. CVSR18

CVSR24

CPVSR18

CPVSR24

DESCRIPTION

QTY.

901058-01

901059-01

901066-01

901064-02

901208-01

901136-01

901242-01

101628-01

—

901243-01

901635-01

901625-01

901545-01

—

901058-01

901059-01

901066-01

901064-03

901208-02

901136-02

901242-01

101628-01

—

901243-02

901636-01

901626-01

901545-01

901546-01

901541-01

901547-01

—

901058-01

901059-01

901066-01

901064-02

901208-01

901137-01

901242-01

101628-01

901431-01

901246-01

—

901058-01

901059-01

901066-01

901064-03

901208-02

901137-02

901242-01

101628-01

901431-01

901246-02

—

Brass 3/8 FLR x 1/2 FPT Adapter

Brass 3/8 FLR x 3/8 FPT Adapter

Brass Air Mixer - Natural Gas

Natural Gas Injector

Burner Manifold

Burner Pan

Damper Clamp - Std. Assembly

Gas Line - 10" Flex

Grate Steps

Log Grate

Bottom Front Log

—

Bottom Rear Log

CPR12/CP Top Log

CPR13S/CP Top Log

CPR13/CP Top Log

CPR14/CP Top Log

Bottom Front Log

Bottom Rear Log

VR11/CH Top Log

CHR10/CH Top Log

CHR11/CH Top Log

CHR13/CH Top Log

CHR13Y/CH Top Log

901541-01

901547-01

—

901641-01

901625-02

901580-04

901555-01

901550-01

901551-01

901556-01

901642-01

901626-02

—

901555-01

901550-01

901551-01

901556-01

—

PARTS AVAILABLE — NOT SHOWN

901156-01

901155-01

901156-01

901155-01

901156-01

901155-01

901156-01

901155-01

.125# Bag Embers

1.5# Bag Ash Bed Material

(Vermiculite)

Aluminum Rating Plate-Radco Gen.

Instruction Manual - V/G RGA 2-72

901036-01

901265-01

901036-01

901265-01

901036-01

901265-01

901036-01

901265-01

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

ILLUSTRATED

PARTS

BREAKDOWN

RADCO BURNER

MODELS CVDR18,

CVDR24, AND CVDR30

Berkshire Split Oak Logs

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

This list contains replaceable parts used in your log set. When ordering parts, follow the

instructions listed under Replacement Parts on page 20 of this manual.

PARTS LIST

RADCO BURNER

MODELS CVDR18,

CVDR24, AND CVDR30

KEY PART NUMBER FOR

NO. CVDR18

CVDR24

CVDR30

DESCRIPTION

QTY.

901058-01

901059-01

901066-01

901064-02

901209-01

901137-01

901242-01

101628-01

901430-01

901246-01

901681-01

901078-01

901076-01

901645-01

901528-01

901591-03

901587-03

—

901058-01

901059-01

901066-01

901064-03

901209-02

901137-02

901242-01

101628-01

901430-01

901246-02

901681-01

901078-01

901076-01

901646-01

901566-01

901591-03

901587-03

901551-02

901527-03

901541-03

—

901058-01

901059-01

901066-01

901064-04

901209-03

901137-03

901242-01

101628-01

901431-01

901246-03

901681-01

901078-01

901076-01

901647-01

901567-01

901591-03

901587-03

901551-02

901527-03

901541-03

901528-01

Brass 3/8 FLR x 1/2 FPT Adapter

Brass 3/8 FLR x 3/8 FPT Adapter

Brass Air Mixer - Natural Gas

Natural Gas Injector

Burner Manifold

Burner Pan

Damper Clamp - Std. Assembly

Gas Line - 10" Flex

Grate Steps

Log Grate

Burner Strap

Nut #8/32

Screw #8/32 x 3/8

Bottom Front Log

Bottom Rear Log

VCR11/CC Top Log

VCR9/CC Top Log

CHR13/CC Top Log

CS12/CC Top Log

CPR13/CC Top Log

CS16/CC Top Log

901527-03

901541-03

—

PARTS AVAILABLE — NOT SHOWN

901156-01

901155-01

901156-01

901155-01

901156-01

901155-01

.125# Bag Embers

1.5# Bag Ash Bed Material

(Vermiculite)

Aluminum Rating Plate-Radco Gen.

Instruction Manual - V/G RGA 2-72

901036-01

901265-01

901036-01

901265-01

901036-01

901265-01

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

ON/OFF SAFETY VALVE/

PILOT KIT - GA9050-1

(Not Shown)

CLEANING AND

MAINTENANCE

ACCESSORIES

Purchase these fireplace accessories from

your local dealer. If they can not supply

theseaccessories,callDESAInternational’s

Sales Department at 1-800-432-2382 for

information. You can also write to the ad-

dress listed on the back page of this manual.

• Keep the area around the log set clean

and clear of debris.

For all models. Required for Propane/LP

installation.

• Occasionally, you may use a soft bristle

brush to clean logs.

REMOTE READY VALVE/

PILOT KIT - GA9150-1

(Not Shown)

• Once every year a qualified agency or

certified chimney sweep should exam-

ine and clean the venting system of the

fireplace.

For all models.

INDIVIDUAL ROUND LOG

GA9450

(Not Shown)

REPLACEMENT

PARTS

For all models. Use when more logs are

desired. Carton of 6

Note: Use only original replacement parts.

Thiswillprotectyourwarrantycoveragefor

parts replaced under warranty.

INDIVIDUAL SPLIT LOG

GA9550

(Not Shown)

PARTS UNDER WARRANTY

MANUAL SHUTOFF VALVE

GA5010

Contact authorized dealers of this product or

Parts Central (see page 21). If they can’t

supplyoriginalreplacementpart(s),callDESA

International’sTechnicalServiceDepartment

at 1-800-DESA LOG (1-800-337-2564).

For all models. Carton of 6.

PINE CONES - GA9650

(Not Shown)

Forallmodels.Manualshutoffvalvewith1/8"

NPT tap. Fits 1/2" NPT pipe.

For all models. Use for additional decora-

tion only. Carton of 6 Boxes (3 pine cones

per box).

WhencallingDESAInternational,haveready

•

your name

your address

modelandserialnumbersofyourfireplace

how fireplace was malfunctioning

type of gas used (propane/LP or natural

gas)

ASH BED MATERIAL

(Vermiculite) - GA9750

(Not Shown)

For all models. Carton of 6.

•

purchase date

GLOWING EMBERS - GA9950

(Not Shown)

RECEIVER AND HAND-

HELD REMOTE CONTROL

KIT - GHRC Series

Usually, we will ask you to return the defec-

tive part to the factory.

For all models. Use for firebox decoration

only.

PARTS NOT UNDER WAR-

RANTY

For all models. Allows the gas log set to be

turned on and off by using a hand-held

remote control. Valve/Pilot Kit GA9100

must be used with this remote.

SILICA SAND - GA9850

(Not Shown)

Contact authorized dealers of this product

or Parts Central (see page 21). If they can’t

supply original replacement part(s), call

DESA International’s Parts Department at

1-800-972-7879 for referral information.

For all models. Use for firebox decoration

only. Carton of 6.

LAVA ROCK - GA6067

(Not Shown)

WhencallingDESAInternational,haveready

•

model number of your fireplace

the replacement part number

For all models. Use for firebox decoration

only.

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

ACCESSORIES

Continued

DECORATIVE ASH BED

CONTROL COVER - CDABK

(Not Shown)

An attractive way to cover control knob

and piezo ignitor.

18" ORNAMENTAL GRATE

ENHANCER - GA9350

(Not Shown)

For 18" models only. Additional decoration

for front grate.

24" ORNAMENTAL GRATE

ENHANCER - GA9360

(Not Shown)

For 24" models only. Additional decoration

for front grate.

30" ORNAMENTAL GRATE

ENHANCER - GA9370

(Not Shown)

For 30" models only. Additional decoration

for front grate.

These Parts Centrals are privately-owned businesses. They have agreed to support our

customer’s needs by providing original replacement parts and accessories.

PARTS CENTRALS

Baltimore Electric

1348 Dixwell Avenue

Hamden, CT 06514

1-800-397-7553

Four Flags Power Products

East Coast Energy Products

707 Broadway

W. Long Branch, NJ 07764

732-870-8809

Halco Enterprises

208 Carter Drive, Unit 21

West Chester, PA 19382-4500

610-430-7717

1115 Stateline Road

Niles, MI 49120

616-684-2697

1-800-268-4983

Parts Only

203-248-7553

Parts Department

1-800-755-8809

1-800-368-0803

Parts Department

Portable Heater Parts

342 N. County Rd. 400 E.

Valparaiso, IN 46383

All States

Master Parts Distributor

1251 Mound Ave. NW

Grand Rapids , MI 49504-2672

616-791-0505

Tarantin Tank Co.

P.O. Box 6129

Freehold, NJ 07728

908-780-9340

LaPorte’s Parts and Service

2444 North 5th Street

Hartsville, SC 29550-7704

803-332-0191

219-462-7441

1-800-362-6951

Parts Department

1-800-446-1446

Fax: 1-616-791-8270

Parts Department

1-800-922-0724

Parts Department

Cans Unlimited, Inc.

P.O. Box 645

Taylor, SC 29687

All States

803-879-3009

1-800-845-5301

Parts Department

Dayton Hardware

P.O. Box 275

North Dayton Station

Dayton, OH 45404

All States

513-258-3721

OH 1-800-762-3426

Parts Department

FBD

Washer Equipment Co.

1715 Main Street

Kansas City, MO 64108-2195

KS, MO, AR

816-842-3911

Parts Department

1349 Adams St.

Bowling Green, KY 42103

502-846-1199

1-800-654-8534

Fax: 1-800-846-0090

Heater and Fireplace Store

1922 N. Route 9

Cape May Court, NJ 08210-1110

609-624-0678

Parts Department

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

RADCO BURNERS

FOR VENTED NATURAL GAS LOGS

NOTES

_______________________________________________________________________________________________

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

OWNER’S MANUAL

NOTES

_______________________________________________________________________________________________

901048

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY INFORMATION

KEEP THIS WARRANTY

Model

Serial No.

Date Purchased

Always specify model and serial numbers when communicating with the factory.

We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written

warranty. We make no other warranty, expressed or implied.

LIMITED WARRANTY

VANGUARD VENTED GAS LOGS

DESA International warrants this product to be free from defects on burner system for three (3) years and logs for a lifetime from

the date of first purchase, provided that the product has been properly installed, operated and maintained in accordance with all

applicable instructions. To make a claim under this warranty the Bill of Sale or cancelled check must be presented.

This warranty is extended only to the original retail purchaser. This warranty covers the cost of part(s) required to restore this log set

toproperoperatingconditionandanallowanceforlaborwhenprovidedbyaDESAAuthorizedServiceCenter. Warrantypart(s)MUST

be obtained through authorized dealers of this product and/or DESA International who will provide original factory replacement parts.

Failuretouseoriginalfactoryreplacementpartsvoidsthiswarranty. ThelogsetMUSTbeinstalledbyaqualifiedinstallerinaccordance

with all local codes and instructions furnished with the unit.

This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become

damaged as a result of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost,

labor, transportation and any and all such other costs related to repairing a defective log set will be the responsibility of the owner.

TOTHE FULL EXTENT ALLOWEDBY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT;

THIS EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURA-

TION OF ANY AND ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS

FOR A PARTICULAR PURPOSE TO THREE (3) YEARS ON BURNER SYSTEM AND A LIFETIME ON LOGS FROM THE

DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY IS HEREBY LIMITED TO THE PURCHASE

PRICE OF THE PRODUCT AND DESA INTERNATIONAL SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES

WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.

Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential

damages, so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

For information about this warranty write:

INTERNATIONAL

2701 Industrial Drive

P.O. Box 90004

Bowling Green, KY 42102-9004

www.desatech.com

901048-01

901048 01

Rev. A

07/99

NOT A UPC

Download from Www.Somanuals.com. All Manuals Search And Download.

Coda Stereo Amplifier 02b User Manual
Craftsman Chipper 247776360 User Manual
Curtis DVD Player DVD1093B User Manual
Curtis TV Receiver KCR2620DUK User Manual
Dacor Microwave Oven DMT2420R User Manual
Ducane HVAC Air Conditioner 2SG13B User Manual
Extron electronic Stereo Receiver FOX 500 DVI Rx User Manual
Fujitsu Time Clock ETERNUS2000 User Manual
Furman Sound Stereo Amplifier MS2A 1 User Manual
Generac Power Systems Portable Generator 005012 1 User Manual