CAST IRON STOVE AND DIRECT-VENT
(FREESTANDING FIREPLACE HEATER)
BURNER SYSTEM
OWNER’S OPERATION AND INSTALLATION MANUAL
NATURAL GAS BURNER SYSTEM MODEL CDVBNC,
PROPANE/LP GAS BURNER SYSTEM MODEL CDVBPC
REMOTE READY
IMPORTANT: This direct-vent burner system must be installed into approved Comfort Glow cast
iron stove bodies, models CISGA series and CISCA series ONLY. See page 3 of this manual.
WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property dam-
age, personal injury, or loss of life.
WARNING: Improper instal-
lation,adjustment,alteration,
service, or maintenance can
causeinjuryorpropertydam-
age. Refer to this manual for
correct installation and op-
erationalprocedures.Foras-
sistance or additional infor-
mation consult a qualified in-
staller,serviceagency,orthe
gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this or any other appliance.
FOR YOUR SAFETY
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch
• Do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthefiredepartment.
Installation and service must
be performed by a qualified
installer, service agency, or
the gas supplier.
This appliance may be installed in an aftermarket* permanently located, manufactured
(mobile) home, where not prohibited by state or local codes.
This appliance is only for use with the type of gas indicated on the rating plate. This appliance
is not convertible for use with other gases, unless a certified kit is used.
* Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer.
Save this manual for future reference.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
PRODUCT IDENTIFICATION
3
SAFETY INFORMATION
PRODUCT IDENTIFICATION
Continued
5. This stove reaches high temperatures. Keep children and adults
away from hot surfaces to avoid burns or clothing ignition.
Stove will remain hot for a time after shutdown. Allow sur-
faces to cool before touching.
Cast Iron
Stove Body
6. Carefully supervise young children when they are in the room
with stove.
7. Do not modify the burner or stove under any circumstances.
Any parts removed for servicing must be replaced prior to op-
erating burner system.
Log Set
8. Turn burner system off and let cool before servicing, install-
ing, or repairing. Only a qualified service person should in-
stall, service, or repair the stove or burner system. Have burner
system inspected annually by a qualified service person.
ON
OFF
AUTO
9. You must keep control compartments, burners, and circulat-
ing air passages clean. More frequent cleaning may be needed
due to excessive lint and dust from carpeting, bedding mate-
rial, pet hair, etc. Turn off the gas valve and pilot light before
cleaning stove or burner system.
ON/OFF
Control
Piezo Ignitor
Switch
Valve
Cast Iron
10. Have venting system inspected annually by a qualified service
person. If needed, have venting system cleaned or repaired.
See Cleaning and Maintenance, page 28.
Stove Body
Burner
Vent
Opening
11. Keep the area around your stove clear of combustible materi-
als, gasoline, and other flammable vapor and liquids. Do not
run burner system where these are used or stored. Do not place
items such as clothing or decorations on or around stove.
Rear
Cover
12. Do not use this stove to cook food or burn paper or other objects.
13. Never place anything on top of stove.
Pilot
Assy
14. Do not use any solid fuels (wood, coal, paper, cardboard, etc.)
in this stove. Use only the gas type indicated on burner system
nameplate.
Glass
Door
Assy
Blower with
Adjustment
(Optional
15. This appliance, when installed, must be electrically grounded
in accordance with local codes or, in the absence of local codes,
with the National Electrical Code, ANSI/NFPA 70, or the Ca-
nadian Electrical Code, CSA C22.1.
Installation)
16. Do not obstruct the flow of combustion and ventilation air in
any way. Provide adequate clearances around air openings into
the combustion chamber along with adequate accessibility
clearance for servicing and proper operation.
Grate
Assembly
Glowing
Embers
Lava Rock
17. Do not install stove directly on carpeting, vinyl tile, or any com-
bustible material other than wood. The stove must set on a metal
or wood panel extending the full width and depth of the stove.
Figure 1 - Comfort Glow Direct-Vent Burner System Shown
Installed in Approved Comfort Glow Cast Iron Stove Body
Models CISGA Series and CISCA Series Only
18. Do not use stove or burner system if any part has been ex-
posed to or under water. Immediately call a qualified service
person to arrange for replacement of the unit.
19. Do not operate burner system if any log is broken.
20. Do not use a blower insert, heat exchanger insert, or other ac-
cessory not approved for use with this stove.
21 . Do not operate burner system with glass door removed, cracked,
or broken.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCAL CODES
4
PRODUCT FEATURES
GLOSSARY OF TERMS
PRE-INSTALLATION PREPARATION
Location and Space Requirements
LOCAL CODES
PRE-INSTALLATION
PREPARATION
Install and use stove and burner system with care. Follow all local
codes. In the absence to local codes, use the current National Fuel
Gas Code ANSI Z223.1/NFPA 54* (USA) or the current CSA-
B149.1 Installation Code (Canada).
WARNING: A qualified service person must in-
stall stove and burner system. Follow all local codes.
*Available from:
American National Standards Institute, Inc.
1430 Broadway
CAUTION: This stove with burner system creates
warm air currents. These currents move heat to wall
surfaces next to stove. Installing stove next to vinyl
or cloth wall coverings or operating stove where
impurities(suchas,butnotlimitedto,tobaccosmoke,
aromatic candles, cleaning fluids, oil or kerosene
lamps, etc.) in the air exist, may discolor walls or
cause odors.
New York, NY 10018
National Fire Protection Association, Inc.
Batterymarch Park
Quincy, MA 02269
PRODUCT FEATURES
OPERATION
LOCATION AND SPACE REQUIREMENTS
This cast iron stove with burner system is clean burning and vents
easily through outside walls or vertically using outside air for
combustion. Heat is generated by both realistic flames and glowing
embers. When used without the blower accessory, the stove with
burner system requires no electricity making it ideal for emergency
backup heat.
Determine the safest and most efficient location for your Comfort
Glow cast iron stove. Make sure that rafters and wall studs are not
in the way of the venting system. Choose a location where the heat
output is not affected by drafts, air conditioning ducts, windows, or
doors. Figure 2 shows some common locations. Read all venting
information in this manual. Be aware of all restrictions and precau-
tions before deciding the exact location for your stove.
PIEZO IGNITOR
When deciding the location of your stove, follow these rules:
This burner system has a piezo ignitor. This system requires no
matches, batteries, or other sources to light burner system.
1. Do not connect this stove and burner system to a chimney flue
serving a separate solid-fuel burning fireplace or appliance.
2. Due to high temperatures, do not locate this stove in high traf-
fic areas or near furniture or draperies.
GLOSSARY OF TERMS
Chase - A boxlike enclosure to protect venting from the elements
3. Proper clearances must be maintained, see Figures 3 and 4 on
page 5.
when the venting run is on the outside of a structure.
Mastic - A pliable sealant for use around the vent terminal.
4. This stove is a freestanding unit designed to set directly on the
floor. If your stove is to be installed directly on carpeting, vi-
nyl tile, or any combustible material other than wood, it must
be installed on a metal or wood panel extending the full width
and depth of the stove. See Figure 5, page 5.
Snorkel Termination - A box that raises the horizontal termination
above ground level clearances.
Vent Terminal - Mounted on an outside wall or roof to separate the
inlet and outlet of the vent system and protect it from weather.
VinylSidingStandoff-Ametalboxthatseparatestheventcapfrom
vinyl siding.
On Wall with
Horizontal
Termination
Wall Thimble/Firestop - A metal plate used to secure the vent pipe
when it passes through a wall or ceiling.
On Wall with
Vertical Termination
Through Ceiling
Corner Installation
Figure 2 - Common Stove Locations
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-INSTALLATION PREPARATION
Location and Space Requirements (Cont.)
5
PRE-INSTALLATION
PREPARATION
Continued
Ceiling
42"
4"
4"
36"
from
Front
4"
Back
Wall
Figure 4 - Clearance for Corner Installation
25"
Floor
Front
Must contain
a minimum
of 1" clearance
to combustibles
25 5/8
"
Figure 5 - Stove with Burner System Bottom Dimensions
29"
4"
6"
Front
Figure 3 - Clearances for Standard Installation
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY
Stove Body Assembly
6
CAST IRON STOVE AND
DIRECT-VENT BURNER
SYSTEM ASSEMBLY
8. Fasten each leg to stove with four (4) M8 x 1.25 - 20mm bolts.
Use a flat washer and lock washer with each bolt. Tighten bolts
into threaded holes on stove body (see Figures 9 and 10). Use
an adjustable wrench or a 12mm socket.
STOVE BODY ASSEMBLY
1. Lift off corrugated box enclosing stove body crating.
2. Remove all screws fastening the wood frame enclosure. Spread
wood frame open and lift away from plastic-bagged stove body.
The bottom pieces of pallet wood will remain bolted to the
stove body.
9. Attach stove door by inserting step bolt through door hinge pivot
hole and into threaded hole in stove body (see Figure 9 and
Figure 11 on page 7). Use an adjustable wrench or a 12mm
socket to fasten step bolt. Tighten step bolt until snug. Make
sure door moves freely.
3. Remove plastic bag from stove body.
4. Remove back panel from stove (see Figure 6). Use an adjust-
able wrench or a 10 mm socket. Remove six (6) bolts and wash-
ers. Keep bolts and washers to reattach back panel later.
Front
Pallet
Bolt
Wood
5. Remove all contents from inside stove cavity. Contents include:
(1) - Stove bottom (Discard. Not used in this application.)
(4) - Legs with leg leveler bolts
(1) - Bottom door
Bottom Of
Stove Unit
Pallet
Wood
(1) - Top grate
(1) - Hardware kit bag with fasteners
6. Carefully lay stove body on back to attach bottom components
to stove body (see Figure 7). Rest stove on drop cloth or blan-
ket to avoid scratching stove edges.
Figure 8 - Removing Pallet Wood from the Bottom of the Stove
Door Catch Bolt With
Adjustable Hex Nuts Hole
Door Hinge Step
Bolt Hole
7. Remove remaining pallet wood attached to bottom of stove
body (see Figure 8). Use an adjustable wrench to remove bolts.
Front
Leg
Leg
Hole
Hole
Bolt
Product
Identification
Label
Back
Stove
Panel
Leg Hole
Bottom Of
Stove Unit
Figure 6 - Removing Back Panel
Figure 9 - Locating Threaded Holes for Legs, and Door
Attachment
Top of Stove Unit
Front of
Stove
Unit
Top of
Stove
Unit
Front of
Stove Unit
Drop
Cloth/
Blanket
Bolt
Bottom Of
Stove Unit
Pallet Wood Bolted to Bottom
of Stove Body
Leg
Figure 7 - Laying Stove On Side
Figure 10 - Attaching Stove Legs
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY
Stove Body Assembly (Cont.)
7
Installing Direct-Vent Burner System Into Stove Body
CAST IRON STOVE AND
DIRECT-VENT BURNER
SYSTEM ASSEMBLY
Continued
10. Install door catch bolt (M8 x 1.25-55mm with two M8 hex
nuts) into threaded hole on stove body (see Figure 9, page 6).
Use an adjustable wrench or a 12mm socket. The catch bolt
has two hex nuts attached to it (see Figure 12). The top nut is a
bolt stop and the bottom nut is for door leveling adjustment.
INSTALLING DIRECT-VENT BURNER
SYSTEM INTO STOVE BODY
1. Carefully lift burner system and place into stove body from
the rear of stove.
2. Using screws provided, attach burner system to back of stove.
11. Check general catch bolt alignment with door claw. Make fi-
nal adjustment and door leveling after stove is in normal stand-
ing position.
Screw
12. Carefully lift stove back up on its four attached legs.
13. Set top grate into stove top.
Burner
System
Cast Iron
Stove Body
Stove
Door
Threaded
Hole
Door
Hinge
Step Bolt
Bolt Shoulder
Figure 11 - Attaching Stove Door
Figure 13 - Installing Burner System Into Cast Iron Stove Body
Bolt Stop
Adjusting Nut
Door Claw
Catch Bolt
Door
Figure 12 - Catch Bolt and Door Claw Orientation
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY
Installing Optional Blower Accessory
8
CAST IRON STOVE AND
DIRECT-VENT BURNER
SYSTEM ASSEMBLY
Continued
Installing GA3750/CDA3620T Blowers
INSTALLING OPTIONAL BLOWER
ACCESSORY
1. Align the holes in the top mounting tabs of blower with holes
in wall of rear cover (see Figure 15). Using the 4 screws pro-
vided, mount blower and tighten screws securely.
NOTICE: If installing blower in an existing stove with
burner system with gas connections, shut off gas
supply and disconnect burner system from gas sup-
ply. Contact a qualified service person to do this.
Note: For CDA3620T, make sure the thermal switch has been
properly installed to fit against the back of the burner system.
2. Make sure all wire connections to terminals on blower motor
(and thermal switch where applicable) are securely attached
and that the screw retaining the green ground wire is tight.
Attaching Thermal Switch to CDA3620T
Thermostatically- Controlled Blower
3. Place speed control on back wall inside of rear cover and push
the plastic control shaft through opening (see Figure 15).
WheninstallingtheCDA3620Tthermostatically-controlledblower
accessory, you must first secure the thermal switch to the blower.
4. While supporting speed control, secure control shaft with lock
nut by pushing and turning lock nut with pliers clockwise until
tight against the side of rear cover. Place control knob provided
onto shaft (see Figure 15).
1. Remove the two hex head screws on the blower assembly as
shown in Figure 14.
2. Place the green wire between the bottom hole on the thermal
switch bracket and the bottom hole on the blower assembly.
Insert one of the hex screws into all three pieces and tighten.
5. Plug in blower power cord.
6. Check to make sure that the power cord is completely clear of the
blower wheel and that there are no other foreign objects in blower
wheel. Turn blower on and check for operation. Turn blower off
by rotating knob fully counterclockwise before continuing.
3. Insert the top screw through the thermal switch bracket and
into the blower assembly. Tighten screw.
4. Connect the blue wire on the blower assembly to the right side
of the thermal switch.
WARNING: Never touch the blower wheel while in
operation.
5. Connect the black wire to the left side of the thermal switch.
Black Wire
7. Peel off the backing paper and stick the supplied wiring diagram
decal on the inside of rear cover on right side opposite control.
Blower
Assembly
White Wire
Blower
Control
Knob
Speed Control
Control Shaft
Thermal
Switch with
Bracket
Mounting
Screws
(Included in
Hardware
Pack)
Lock
Nut
Power
Cord
Green
Wire
Hex Head
Screws
Blue Wire
Figure 14 - Attaching Thermal Switch to CDA3620T
Thermostatically-Controlled Blower Accessory
Black
Wire
Wiring
Diagram
Decal
White
Wire
Rear
Cover
Blue
Wire
Green
Ground Wire
Blower
Figure 15 - Installing Optional Blower Accessory (Thermostat
Model CDA3610T Shown)
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
CAST IRON STOVE AND DIRECT-VENT BURNER SYSTEM ASSEMBLY
Installing Optional Blower Accessory (Cont.)
Installing Rear Cover
9
GENERAL VENTING
Location Of Vent Termination
CAST IRON STOVE AND
GENERAL VENTING
These models are approved for use with Simpson Dura-Vent 6 5/8"
direct-vent pipe components and terminations as well as both flex
and rigid Comfort Glow vent components.
DIRECT-VENT BURNER
SYSTEM ASSEMBLY
Continued
Your stove with burner system is approved to be vented either
through the side wall, or vertically using the following guidelines:
WARNING: Failure to position the parts in accor-
dance with supplied diagrams or failure to use only
partsspecificallyapprovedwiththisstoveandburner
system may result in damage or personal injury.
• Only use Comfort Glow or Simpson Dura-Vent GS venting com-
ponents or kits specifically approved for this stove and burner
system.
• Minimum clearance between vent pipes and combustible mate-
rials is 1" (25 mm), except where stated otherwise.
8. Connect or reconnect gas supply to stove and burner system
per Connecting Stove/Burner System to Gas Supply on page • Do not recess venting terminals into a wall or siding.
19 of this manual.
• Install horizontal venting with a 1/4" rise for every 12" of run
toward the termination.
WARNING: A qualified service person must con-
nect burner system to gas supply. Follow all local
codes.
• You may paint the vent terminal with 450ºF (232ºC) heat-resis-
tant paint to coordinate with the exterior finish.
• There must not be any obstruction such as bushes, garden sheds,
fences, decks, or utility buildings within 24" from the front of
the termination cap.
INSTALLING REAR COVER
• Do not locate termination cap where excessive snow or ice build
up may occur. Be sure to clear vent termination area after snow
falls to prevent accidental blockage of venting system. When
using snow blowers, do not direct snow towards vent termina-
tion area.
1. Lift rear panel over vent pipe connection on burner system.
Rear cover will rest on the bottom ledge of the stove body.
2. Using screws provided, attach rear cover to back of stove body.
See Figure 16.
IMPORTANT: This rear cover must be securely in place be-
fore venting pipes are installed.
• You must maintain minimum wall and ceiling clearances shown
in Figures 3 and 4, page 5.
LOCATION OF VENT TERMINATION
Screw
When locating vent termination, it is important to observe the
minimum clearances shown in Figure 17, page 10.
Rear
Cover
*Check with local codes or with the current CAN/CGA B149[.1 or
.2] Installation Codes for Canada or the USA Installations follow
the current National Fuel Gas Code, ANSI Z223.1/NFPA 54.
Burner System
Installed In Cast
Iron Stove Body
Figure 16 - Installing Rear Cover
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL VENTING
Location Of Vent Termination (Cont.)
10
GENERAL VENTING Continued
N
N
D
H
E
V
B
L
C
I
B
Fixed
Openable
Fixed
V
V
Closed
Closed
Openable
G
G
B
F
V
V
G
J
V
A
X
B
B
M
V
A
V
X
K
TERMINATION CAP
G
GAS METER
RESTRICTED AREA
(TERMINATION PROHIBITED)
AIR SUPPLY INLET
V
X
A = clearance above grade, veranda, porch, deck, or balcony
[*12 inches (30.5cm) minimum]
I
= clearance to service regulator vent outlet [*72 inches (182.9cm)
minimum]
B = clearance to window or door that may be opened
[12 inches (30.5cm) minimum]
J
= clearance to non-mechanical air supply inlet to building or the
combustion air inlet to any other fireplace [*12 inches (30.5cm)
minimum]
C = clearance to permanently closed window [minimum 12 inches
(30.5cm) recommended to prevent condensation on window]
D = vertical clearance to ventilated soffit located above the terminal
within a horizontal distance of 24 inches (61cm) from the
center-line of the terminal [18 inches (45.7cm) minimum]
E = clearance to unventilated soffit [12 inches (30.5cm) minimum]
F = clearance to outside corner (see below)
G = clearance to inside corner (see below)
H = *not to be installed above a meter/regulator assembly within
36 inches (91.4cm) horizontally from the center-line of the regulator
K = clearance to a mechanical air supply inlet [*72 inches (182.9cm)
minimum]
L = clearance above paved side-walk or a paved driveway located on
public property [*84 inches (213.4cm) minimum]
M = clearance under veranda, porch, deck [*12 inches (30.5cm) minimum ]
N = clearance above a roof shall extend a minimum of 24 inches (61cm)
above the highest point when it passes through the roof surface and
any other obstruction within a horizontal distance of 18 inches (45.7cm)
vent shall not terminate directly above a side-walk or paved driveway which is located between two
single family dwellings and serves both dwellings*
only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*
as specified in CAN/SGA B149 (.1 or .2) Installation Codes (1991) for Canada or for U.S.A. installation follow
the current National Fuel Gas Code, ANSI Z223.1
*
Note: Local codes or regulations may require different clearances
Termination Clearances for Buildings with Combustible and Noncombustible Exteriors
Inside Corner
Outside Corner
Recessed Location
D
C
C
A
A = 6" (15.2cm)
E
V
V
V
B = 6" (15.2cm)
B
Balcony with No Side Wall
Balcony with Perpendicular Side Wall
C = Maximum depth of 48" (121.9cm) for
recessed location
D = Minimum width for back wall of
recessed location -
Combustible - 38" (96.5cm)
Noncombustible - 24" (61cm)
E = Clearance from corner in
recessed location-
H
V
J
G
V
Combustible &
Noncombustible
H = 24" (61cm)
J = 20" (50.8cm)
Combustible - 6" (15.2cm)
Noncombustible - 2" (5.1cm)
G = Combustible 24" (61cm)
Noncombustible 18" (45.7cm)
Figure 17 - Minimum Clearances for Vent Terminations
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
Installation Precautions
Installation Planning
11
VENTING INSTALLATION
WARNING: Read all instructions completely and
thoroughly before attempting installation. Failure to
do so could result in serious injury, property damage
or loss of life. Operation of improperly installed and
maintained venting system could result in serious
injury, property damage or loss of life.
WARNING: Horizontal sections of this vent sys-
tem require a minimum clearance of 2" from the top
of the pipe and 1" minimum to the sides and bottom.
Verticalsectionsofthissystemrequireaminimumof
1" clearance to combustible materials on all sides of
the pipe.
INSTALLATION PLANNING
WARNING: Seal all vent connections. Seal only
the outer pipe connections with high temperature
silicone (600°F/316° C). Before joining elbows and
pipes, apply a bead of high temperature silicone
sealant (GE RTV 106/Loctite RTV 81585) to the male
end of the elbow or pipe. High temperature silicone
must also be used to re-seal any connections after
maintenance to venting system.
There are two basic types of direct-vent installation:
• Horizontal Termination
• Vertical Termination
It is important to select the proper length of vent pipe for the type of
termination you choose. It is also important to note the wall
thickness.
For Horizontal Termination: Select the amount of vertical rise
desired. The horizontal run of venting must have 1/4" rise for every
12" of run towards the termination.
NOTICE: Failure to follow these instructions will void
the warranty.
You may use one or two 90° elbows in this vent configuration. See
Horizontal Termination Configurations on page 14.
INSTALLATION PRECAUTIONS
Consult local building codes before beginning the installation. The
installer must make sure to select the proper vent system for
installation. Before installing vent kit, the installer must read this
stove and burner system manual and vent kit instructions.
WARNING: Never run the vent pipe downward as
this may cause excessive temperatures which could
cause a fire.
Only a qualified service person should install venting system. The
installer must follow these safety rules:
For Vertical Termination: Measure the distance from the burner
system flue outlet to the ceiling. Add the ceiling thickness, the
vertical rise in an attic or second story, and allow for sufficient vent
heightabovetheroofline.Youmayuseoneortwo90°elbowsinthis
vent configuration. See Vertical Termination Configurations on
pages 16 and 17.
• Wear gloves and safety glasses for protection
• Use extreme caution when using ladders or when on roof tops
• Be aware of electrical wiring locations in walls and ceilings
The following actions will void the warranty on your venting
system:
Note: You may use two 45° elbows in place of a 90° elbow. You
must follow rise to run ratios when using 45° elbows.
• Installation of any damaged venting component
• Unauthorized modification of the venting system
Fortwo-storyapplications, firestopsarerequiredateachfloorlevel.
If an offset is needed in the attic, additional pipe and elbows will be
• Installation of any component part not manufactured or approved required (see Figure 29, page 15).
by DESA International
Youmayuseachasewithaventterminationwithexposedpipeonthe
exterior of the house. See Installing Vent System in a Chase, page 12.
• Installation other than as instructed by these instructions
Your Comfort Glow stove with direct-vent burner system has been
tested for a maximum 17" wall thickness when using a 60º elbow
directlyoffthebackofthestove. Themaximumhorizontalrunis20'
with 8' vertical rise (see Installation for Horizontal Termination,
pages 12 through 14). The maximum vertical run is 30' (see
Installation for Vertical Termination, pages 15 through 17).
WARNING: This stove with burner system and
ventassemblymustbeventeddirectlytotheoutside.
The venting system must NEVER be attached to a
chimney serving a separate solid fuel burning appli-
ance. Each gas appliance must use a separate vent
system. Do not use common vent systems.
It is very important that the venting system maintain its balance
between the combustion air intake and the flue gas exhaust. Certain
limitationsapplytoventconfigurationsandmustbestrictlyfollowed.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
Installation Planning (Cont.)
12
Installation For Horizontal Termination
VENTING INSTALLATION
Continued
Snorkel
Installing Vent System in a Chase
A chase is a vertical boxlike structure built to enclose venting that runs
alongtheoutsideofabuilding.Achaseisnotrequiredforsuchventing.
NOTICE: Treatment of firestops and construction of
the chase may vary from building type to building
type. These instructions are not substitutes for the
requirements of local building codes. You must fol-
low all local building codes.
12" Minimum
Note: When installing in a chase, you should insulate the chase as
you would the outside walls of your home. This is especially
important in cold climates. Minimum clearance between vent pipes
and combustible materials such as insulation is 1".
INSTALLATION FOR HORIZONTAL
TERMINATION
1. Determine the route your horizontal venting will take. Note:
The location of the horizontal vent termination on the exterior
wall must meet all local and national building codes and must
not be easily blocked or obstructed.
Figure 18 - Snorkel Termination
Snorkel
WARNING: Do not recess vent terminal into a wall
or siding.
Snorkel terminations are available (see page 18) for 14" and
36" terminations requiring a vertical rise on the exterior of the
building (see Figures 18 and 19). Follow the same installation
procedures used for standard horizontal terminations. If install-
ing the snorkel termination below grade (basement applications),
you must provide proper drainage to prevent water from enter-
ing the snorkel termination (see Figure 19). Do not back fill
around the snorkel termination.
12" Minimum
Adequate
drainage
2. Rigid vent pipes and fittings have special twist-lock connec-
tions. Assemble the desired combination of pipe and elbows
to the appliance adaptor with pipe seams oriented towards the
wall or floor.
Twist-lock Procedure: The female ends of the pipes and fit-
tings have four locking lugs (indentations). These lugs will
slide straight into matching slots on the male ends of adjacent
pipes and fittings. (All connections must be sealed with high
temperature silicone sealant as specified in the second warn-
ing statement on page 11.) Push the pipe sections together and
twist one section clockwise approximately one-quarter turn
until the sections are fully locked. See Figure 20, page 13.
Note: Horizontal runs of vent must be supported every three
feet. Use wall straps for this purpose.
Figure 19 - Snorkel Termination with Drainage Pipe
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
13
Installation For Horizontal Termination (Cont.)
VENTING INSTALLATION
Continued
3. Attach vent pipe assembly to the fireplace. Set fireplace in 5. Conbustible ExteriorWall Only: Slide the interior wall firestop
front of it’s permanent location to insure minimum clearances.
over the vent pipe before connecting the horizontal run to the
Mark the wall for a 10" square hole (for noncombustible ma-
terial such as masonry block or concrete, a 7 /2" diameter
vent cap (see Figure 24).
1
6. Carefully move the stove with vent assembly attached toward
the wall and insert the vent pipe into the horizontal termina-
tion. The pipe overlap should be a minimum of 1 1/4". Apply
silicone to the connection. Fasten all vent connections with
screws provided.
hole is acceptable). See Figure 21. The center of the hole
should line up with the center-line of the horizontal rigid vent
pipe. Cut a 10"x10" (25.4cm x 25.4cm) square hole through
1
combustible exterior wall (7 /2" [19.1cm] diameter hole if
noncombustible). Frame as necessary (see Figure 21).
7. Conbustible ExteriorWall Only: Slide the wall firestop against
the interior wall surface and attach with screws provided (see
Figure 24).
4. Noncombustible Exterior Wall: Apply a bead of non-harden-
ing mastic around the outside edge of the vent cap. Position the
vent cap in the center of the 7 1/2" hole on the exterior wall with
the arrow on the vent cap pointing up. Attach the vent cap with
four wood screws provided (see Figure 22). Note: Replace the
wood screws with appropriate fasteners for stucco, brick, con-
crete, or other types of siding.
Vent Cap
WARNING: Do not recess vent termination in to
any wall. This will cause a fire hazard.
Wood Screw
Combustible ExteriorWall: For vinyl siding, stucco, or wood
exteriors, a siding standoff must be installed between the vent
cap and exterior wall. The siding standoff prevents excessive
heat from damaging siding materials. Siding materials must be
cut to accommodate standoff. Bolt the vent cap to the stand-
off. Apply non-hardening mastic around outside edge of the
standoff. Position the standoff/cap assembly in the center of
the 10" square hole and attach to exterior wall with wood screws
provided (see Figure 23). The siding standoff must sit flush
against the exterior fascia material.
Figure 22 - Installing Horizontal Vent Cap (Noncombustible
Exterior)
Cut Vinyl Siding Away
to Fit Standoff
Vinyl Siding Standoff
(Apply Mastic to All
Four Sides)
Vent
Termination
Female
Locking
Lugs
Male
Slots
Figure23-InstallingVinylSidingStandoff(CombustibleExterior)
Rigid Vent Pipe
Interior Wall
Interior Wall Firestop
Surface
(Combustible
Exterior Wall Only)
Figure 20 - Vent Pipe Connections
Screw
Vent Cap
Horizontal
(Horizontal
Vent Pipe
Termination)
Figure 24 - Connecting Vent Cap with Horizontal Vent Pipe
Figure 21 - Vent Opening Requirements
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
Installation For Horizontal Termination (Cont.)
14
VENTING INSTALLATION
Continued
Horizontal Termination Configurations
Figures 25 through 28 show different configurations for venting
with horizontal termination. Each figure includes a chart with
vertical minimum/maximum and horizontal maximum dimensions
which must be met. Seal all connections with high temperature
silicone sealant (outer pipe only) as specified in the second warning
statement on page 11. All horizontal terminations require 1/4" rise
per 12" of horizontal run.
Venting with Two 90° Elbows
Horizontal Venting
Vertical (V)
Horizontal (H1)
Horizontal (H1) +
Horizontal (H2)
Vertical (V)
35" min.
Horizontal (H)
20" max.
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' min.
8' max.
6' max.
12' max.
18' max.
20' max.
20' max.
Figure 25 - Horizontal Termination Configuration for Rigid
Venting
Figure 27 - Horizontal Termination Configuration for Rigid
Venting Using Two 90° Elbows
Horizontal Venting
Venting with Two 90° Elbows
Vertical (V)
Horizontal (H)
Vertical (V)
Horizontal (H1) +
Horizontal (H2)
42" min.
32" max.
(30° elbow with 6" adaptor, 90° elbow, no vertical pipe)
53" min. 44" max.
(30° elbow with 6" adaptor, 1' vertical pipe, 90° elbow)
5' min.
6' min.
7' min.
8' min.
20' max.
6' max.
12' max.
18' max.
20' max.
20' max.
60" min.
72" min.
89" min.
60" max.
84" max.
20' max.
Note: This configuration for use with corner installation.
Figure 28 - Horizontal Termination Configuration for Rigid
Venting Using Two 90° Elbows with Termination at 90° with
Stove
Figure 26 - Horizontal Termination Configuration for Rigid
Venting Using One 90° Elbow
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
15
Installation For Vertical Termination
VENTING INSTALLATION
Continued
2. Assemble the desired lengths of pipe and elbows necessary to
reach from the burner system flue up through the firestop. All
connections must be sealed with high temperature silicone seal-
ant as specified in the second warning statement on page 11.
Be sure all pipe and elbow connections are fully twist-locked
(see Figure 20, page 13).
INSTALLATION FOR VERTICAL
TERMINATION
NOTICE: Use rigid pipe only. Flex venting is not to be
used with a vertical termination.
3. Cut a hole in the roof using the locating hole as a center point.
(Cover any exposed open vent pipes before cutting hole in roof.)
The 10"x10" hole must be measured on the horizontal; actual
length may be larger depending on the pitch of the roof. There
must be a 1" clearance from the vent pipe to combustible mate-
rials. Frame the opening as shown in Figure 21 on page 13.
1. Determine the route your vertical venting will take. If ceiling
joists, roof rafters, or other framing will obstruct the venting
system, consider an offset (see Figure 29) to avoid cutting
loadbearing members. Note: Pay special attention to these in-
stallation instructions for required clearances (air space) to com-
bustibles when passing through ceilings, walls, roofs, enclo-
sures, attic rafters, etc. Do not pack air spaces with insulation.
Also note maximum vertical rise of the venting system and
any maximum horizontal offset limitations. Offsets must fall
within the parameters shown in Figure 17 on page 10.
4. Connect a section of pipe and extend up through the hole.
Note: If an offset is needed to avoid obstructions, you must
support the vent pipe every 3 feet. Use wall straps for this
purpose (see Figure 29). Whenever possible, use 45° elbows
instead of 90° elbows. The 45° elbow offers less restriction to
the flow of the flue gases and intake air.
2. Set the stove in desired location. Drop a plumb line down from
the ceiling to the position of the burner system exit flue. Mark
the center point where the vent will penetrate the ceiling. Drill
a small locating hole at this point.
5. Place the flashing over the pipe section(s) extending through
the roof. Secure the base of the flashing to the roof and fram-
ing with roofing nails. Be sure roofing material overlaps the
top edge of the flashing as shown in Figure 29. There must be
a 1" clearance from the vent pipe to combustible materials.
Drop a plumb line from the inside of the roof to the locating
hole in the ceiling. Mark the center point where the vent will
penetrate the roof. Drill a small locating hole at this point.
6. Continue to add pipe sections until the height of the vent cap
meets the minimum building code requirements described in
Figure 17 on page 10. Note:You must increase vent height for
steep roof pitches. Nearby trees, adjoining rooflines, steep
pitched roofs, and other similar factors may cause poor draft
or down-drafting in high winds. Increasing the vent height may
solve this problem.
Roof
Flashing
Wall Strap
7. Twist-lock the vent cap onto the last section of vent pipe and
seal outer pipe connection with high temperature silicone seal-
ant as specified in the second warning statement on page 11.
45° Elbow
Note: If the vent pipe passes through any occupied areas above the
first floor, including storage spaces and closets, you must enclose
pipe. You may frame and sheetrock the enclosure with standard
construction material. Make sure and meet the minimum allowable
clearancesto combustibles. Do not fill any of the required airspaces
with insulation.
Ceiling Firestop
Figure 29 - Offset with Wall Strap and 45° Elbows
If area above is a room, install
firestop above framed hole.
If area above is not a room, install
firestop below framed hole.
Flat Ceiling Installation
1. Cut a 10" square hole in the ceiling using the locating hole as a
center point. The opening should be framed to 10"x10" (25.4cm
x 25.4cm) inside dimensions, as shown in Figure 21 on page 13
using framing lumber the same size as the ceiling joists. If the
area above the ceiling is an insulated ceiling or a room, nail
firestop from the top side. This prevents loose insulation from
falling into the required clearance space. Otherwise, install
firestop below the framed hole. The firestop should be installed
with no less than three nails per side (see Figure 30).
Figure 30 - Installing Firestop
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
16
Installation For Vertical Termination (Cont.)
VENTING INSTALLATION
Continued
Cathedral Ceiling Installation
Vertical Termination Configurations
1. Remove shingles or other roof covering as necessary to cut the
rectangular hole for the support box. Mark the outline of the
cathedral ceiling support box on the roof sheathing using the
locating hole as a center point.
2. Cut the hole 1/8" larger than the support box outline (see Fig-
ure 31).
Figures 33 and 34 and Figures 35 and 36 on page 17 show four
different configurations for vertical termination. All connections
must be sealed with high temperature silicone sealant as specified
in the second warning statement on page 11.
Venting with One 90° Elbow
3. Lower the support box through the hole in the roof until the
bottom of the box extends at least 2" below the ceiling (see
Figure 31). Align the support box vertically and horizontally
using a level. Temporarily tack the support box in place through
the inside walls and into the roof sheathing.
Vertical (V)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
4. Using tin snips, cut the support box from the top corners down
to the roofline and fold the resulting flaps over the roof sheath-
ing (see Figure 32). Apply a bead of non-hardening mastic
around the top edges of the support box to make a seal be-
tween the box and the roof. Nail in place with roofing nails.
Remove any combustible material that might be inside of the
support box.
5. Complete the cathedral ceiling installation by following the
same procedures outlined in steps 2 through 7 for Flat Ceiling
Installation, page 15.
Note: Install
restrictor into 4"
collar of burner
system as shown.
Level
Cathedral ceiling
support box
Figure 33 - Vertical Rigid Venting Configuration Using One 90°
Elbow
Venting with Two 90° Elbows
Vertical (V) Horizontal (H1) +
Horizontal (H2)
2" minimum
below finished
ceiling
5' min.
6' min.
7' min.
8' min.
20' max.
2' max.
4' max.
6' max.
8' max.
8' max.
Cut hole 1/8" larger than support
box when projected onto roofline
Figure 31 - Cathedral Ceiling Support Box Installation
Nonhardening Mastic
under all edges of support
box before nailing
Note: Install
restrictor into 4"
collar of burner
system as shown.
Figure 32 - Installed Cathedral Ceiling Support Box
Figure 34 - Vertical Rigid Venting Configuration Using Two 90°
Elbows with Two Horizontal Runs
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
VENTING INSTALLATION
Installation For Vertical Termination (Cont.)
High Altitude Installation
17
Parts Lists For Venting Kits And Components
VENTING INSTALLATION
Continued
HIGH ALTITUDE INSTALLATION
Venting with Two 90° Elbows
Your Comfort Glow cast iron stove and direct-vent burner system
has been CSA tested and approved for operation at altitudes in the
USA from 0-2000 ft. and in Canada from 0-4500 ft.
Vertical (V1)
Horizontal (H)
5' min.
6' min.
7' min.
8' min.
6' max.
12' max.
18' max.
20' max.
When installing this stove at an elevation above 2000 feet (in the
USA), you may need to decrease the input rating by changing the
existing burner orifice to a smaller size. Reduce input 4% for each
1000 feet above sea level. Check with your local gas company for
proper orifice size identification.
Note: Vertical (V1) + Vertical (V2) =
20' max.
When installing this stove at an elevation above 4500 feet (in
Canada), check with local authorities.
Note: Install restrictor
into 4" collar of burner
system as shown.
Consultyourlocalgascompanytohelpdeterminetheproperorifice
for your location
For assistance with any high altitude installation contact DESA
International’s Technical Service Department at 1-866-672-6040.
PARTS LISTS FOR VENTING KITS AND
COMPONENTS
Number
Description
P-47-12-K
P-47-24-K
P-47-48-K
12" Black Coaxial Pipe (1 pk)
24" Black Coaxial Pipe (1 pk)
48" Black Coaxial Pipe (1 pk)
Figure 35 - Vertical Rigid Venting Configuration Using Two 90°
Elbows
PA47-712-K 7"-12" Black Coaxial Pipe (1 pk)
P-47-6-K
E47-60-K
E47-30-K
6" Black Coaxial Pipe (1 pk)
60° Elbow (1 pk)
30° Elbow (1 pk)
E47-90-K
E47-45-K
90° Elbow (1 pk)
45° Elbow (1 pk)
PA-47-6-K 6" Adaptor Collar, Black (1 pk)
Vertical Venting
WS-47
SC-47
VT-47
WF-47
Wall Strap (1 pk)
Storm Collar (1 pk)
Vertical Round Termination (1 pk)
Wall Firestop (1 pk)
V = 40' max.
VR-47
Vertical Restrictor (1 pk)
Note: Install restrictor
into 4" collar of burner
system as shown.
FP-47
Firestop Plate (1 pk)
HTS-47
CS-47
Horizontal Square Termination (1 pk)
Cathedral Ceiling Support Box (1 pk)
Roof Flashing 0 to 6/12 Pitch (1 pk)
Roof Flashing 6/12 to 12/12 Pitch (1 pk)
Vinyl Siding Standoff (1 pk)
RF-47-6
RF-47-12
S-47
TP-47
Trim Plate, Black (1 pk)
HT-47
Horizontal Round Termination (1 pk)
14" Snorkel Termination (1 pk)
36" Snorkel Termination (1 pk)
RVKBK Kit Shown
ST-47-14
ST-47-36
Figure 36 - Vertical Rigid Venting Configuration With No
Horizontal Run
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Check Gas Type
Installing Gas Piping To Stove/Burner System Location
18
STOVE AND DIRECT-VENT
BURNER SYSTEM INSTALLATION
CHECK GAS TYPE
CAUTION: Use only new, black iron or steel pipe.
Internally-tinned copper tubing may be used in cer-
tain areas. Check your local codes. Use pipe of 1/2"
diameter or greater to allow proper gas volume to
burner system. If pipe is too small, undue loss of
volume will occur.
Use proper gas type for the burner system unit you are installing. If
you have conflicting gas types, do not install burner system. See
dealer where you purchased the stove and burner system for proper
burner system according to your gas type.
INSTALLING GAS PIPING TO STOVE/
BURNER SYSTEM LOCATION
Installation must include an equipment shutoff valve, union, and
plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge
hook up. NPT tap must be upstream from burner system (see Figure
38, page 19).
WARNING: A qualified service person must con-
nect burner system to gas supply. Follow all local
codes.
IMPORTANT: Install equipment shutoff valve in an accessible
location. The main gas valve is for turning on and shutting off the
gas to the appliance.
CAUTION: For propane/LP units, never connect
burner system directly to the propane/LP supply.
This burner system requires an external regulator
(not supplied). Install the external regulator between
the burner system and propane/LP supply.
Checkyourbuildingcodesforanyspecialrequirementsforlocating
equipment shutoff valve to stoves.
Apply pipe joint sealant lightly to male NPT threads. This will
prevent excess sealant from going into pipe. Excess sealant in pipe
could result in clogged burner system valves.
Installation Items Needed
WARNING: Use pipe joint sealant that is resistant
to liquid petroleum (LP) gas.
Before installing stove and burner system, make sure you have the
items listed below.
• external regulator (supplied by installer)
• piping (check local codes)
• sealant (resistant to propane/LP gas)
• equipment shutoff valve *
• test gauge connection *
• sediment trap
Propane/LP
Supply Tank
External
Regulator
Vent
Pointing
Down
• tee joint
• pipe wrench
• approved flexible gas line with gas connector (if allowed by lo-
cal codes) (not provided)
* A CSA design-certified equipment shutoff valve with 1/8" NPT
tap is an acceptable alternative to test gauge connection. Purchase
theCSAdesign-certifiedequipmentshutoffvalvefromyourdealer.
See Accessories, page 36.
Figure 37 - External Regulator with Vent Pointing Down
(Propane/LP Only)
For propane/LP connections only, the installer must supply an
external regulator. The external regulator will reduce incoming gas
pressure.Youmustreduceincominggaspressuretobetween11and
14 inches of water. If you do not reduce incoming gas pressure,
burner system regulator damage could occur. Install external regu-
lator with the vent pointing down as shown in Figure 37. Pointing
the vent down protects it from freezing rain or sleet.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Installing Gas Piping To Stove/Burner System Location (Cont.)
Connecting Stove/Burner System To Gas Supply
Checking Gas Connections
19
STOVE AND DIRECT-VENT
BURNER SYSTEM INSTALLATION
Continued
Equipment Shutoff Valve
To Flare Fitting on
Control Valve
We recommend that you install a sediment trap in supply line as shown
inFigure38. Locatesedimenttrapwhereitiswithinreachforcleaning.
Installinpipingsystembetweenfuelsupplyandburnersystem. Locate
sediment trap where trapped matter is not likely to freeze. A sediment
trap traps moisture and contaminants. This keeps them from going into
burnersystemgascontrols.Ifsedimenttrapisnotinstalledorisinstalled
wrong, burner system may not run properly.
Flexible Gas Line from
Equipment Shutoff Valve
Provided by Installer
Natural - To Gas Supply
Propane/LP - To
CSA Design-Certified Equipment
Shutoff Valve with 1/8" NPT Tap*
External Regulator
Figure 39 - Flexible Gas Line
Propane/LP - From
External Regulator
(11" W.C. to 14"
CHECKING GAS CONNECTIONS
WARNING: Test all gas piping and connections,
internal and external to unit, for leaks after installing
or servicing. Correct all leaks at once.
W.C. Pressure)
Approved Flexible
Gas Line
Natural - From Gas
Meter (5" W.C. to
10.5" W.C. Pressure)
3" Minimum
WARNING: Never use an open flame to check for
a leak. Apply a noncorrosive leak detection solution
to all gas joints. Bubbles forming show a leak. Cor-
rect all leaks at once.
Cap Pipe Tee
Nipple Joint
Sediment Trap
Figure 38 - Gas Connection
Pressure Testing Gas Supply Piping System
Test Pressures In Excess Of 1/2 PSIG (3.5 kPa)
* The CSA design-certified equipment shutoff valve may be sup-
plied with the appliance or you can purchase it from your dealer.
1. Disconnect burner system and its individual equipment shutoff
valve from gas supply piping system. Pressures in excess of 1/2
psig (3.5 kPa) will damage burner system gas regulator.
CONNECTING STOVE/BURNER SYSTEM TO
GAS SUPPLY
2. Cap off open end of gas pipe where equipment shutoff valve
was connected.
Installation Items Needed
3. Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas burner system or open-
ing main gas valve located on or near gas meter for natural gas
burner system, or using compressed air.
• 5/16" hex socket wrench or nut-driver
• sealant (resistant to propane/LP gas, not provided)
1. Open lower door panel.
4. Check all joints of gas supply piping system. Apply a noncor-
rosive leak test solution to all gas joints. Bubbles forming show
a leak. Correct all leaks at once.
2. Route flexible gas line (provided by installer) from equipment
shutoff valve to burner system. Route flexible gas supply line
through slot in stove bottom and attach to valve.
5. Reconnect burner system and equipment shutoff valve to gas
supply. Check reconnected fittings for leaks.
3. Check all gas connections for leaks. See Checking Gas Con-
nections.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Checking Gas Connections (Cont.)
20
STOVE AND DIRECT-VENT
BURNER SYSTEM INSTALLATION
Continued
Test Pressures Equal To or Less Than 1/2 PSIG (3.5 kPa)
Propane/LP
Supply Tank
Equipment
Shutoff Valve
1. Close equipment shutoff valve (see Figure 40).
2. Pressurize supply piping system by either opening propane/LP
supply tank valve for propane/LP gas burner system or open-
ing main gas valve located on or near gas meter for natural gas
burner system, or using compressed air.
3. Check all joints from propane/LP supply tank or gas meter to
equipment shutoff valve (see Figure 41 for propane/LP or Fig-
ure 42 for natural). Apply a noncorrosive leak test solution to
all gas joints. Bubbles forming show a leak. Correct all leaks
at once.
Pressure Testing Burner System Gas
Connections
Gas Valve
1. Open equipment shutoff valve (see Figure 40).
Figure 41 - Checking Gas Joints for Propane/LP Gas Burner
System
2. Open propane/LP supply tank valve for propane/LP burner
system or main gas valve located on or near gas meter for natu-
ral gas burner system.
Equipment
Shutoff Valve
3. Make sure control knob of burner system is in the OFF position.
4. Check all joints from equipment shutoff valve to thermostat
gas valve (see Figure 41 for propane/LP or Figure 42 for natu-
ral). Apply a noncorrosive leak test solution to all gas joints.
Bubbles forming show a leak. Correct all leaks at once.
Gas Meter
5. Light burner system (see Operating Stove with Burner System,
pages 23 through 26). Check all other internal joints for leaks.
6. Turn off burner system (see To Turn Off Gas to Appliance,
page 24).
Open
Equipment
Shutoff
Valve
Gas Valve
Figure 42 - Checking Gas Joints for Natural Gas Burner System
Closed
Figure 40 - Equipment Shutoff Valve
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Installing Optional Wireless Hand-held Remote Control Accessories - CGHRC and CGHRCTA Series
Removing/Replacing Glass Door
21
STOVE AND DIRECT-VENT
BURNER SYSTEM INSTALLATION
Continued
INSTALLING OPTIONAL WIRELESS HAND-
HELD REMOTE CONTROL ACCESSORIES -
CGHRC AND CGHRCTA SERIES
Installing Remote Receiver
1. Open bottom door on stove body and locate the switch plate
on the left of the valve bracket.
Figure 46 - Installing Remote Receiver
2. Unscrew switch plate (see Figure 43).
3. Disconnect wires from THTP and TH on control valve that
lead to the switch (see Figure 44). Discard switch plate, screws,
and nuts.
Installing 9-Volt Battery in Hand-Held Remote
Control Unit
1. Remove battery cover on back of remote control unit
4. Install battery into receiver battery clip and connect to termi-
nals (see Figure 45).
2. Attach terminal wires to a 9-volt battery (not included). Place
battery into the battery housing.
5. Place receiver into valve bracket and align holes (see Figure 46).
3. Replace battery cover onto remote control unit.
6. Use push-in fasteners included with receiver to secure to
bracket.
Remote
Control
Unit
Terminal
Wires
Battery Cover
9-Volt
Battery
7. Connect the wires from the receiver to the valve at TH and
THTP (see Figure 44).
Battery Housing
Figure 47 - Installing Battery in Hand-Held Remote Control Unit
Figure 43 - Removing Switch Plate
To Control
Switch or
Optional
REMOVING/REPLACING GLASS DOOR
You must remove glass door to install logs, lava rock, and ember
material. To remove glass door, you must first remove the front
panel on stove body.
Accessory
CAUTION:Donotoperatethisburnersystemwith
a broken glass door panel or without the glass door
panel securely in place. For replacement part infor-
mation see Replacement Parts, page 31.
Figure 44 - Control Valve Terminals
Receiver
1. Remove 2 bolts from bottom of stove and one from the top of
stove to remove front panel (see Figure 48, page 22).
2. Remove the screws from the 2 tabs at the top of the glass door
while holding door securely keeping it from falling forward.
9-Volt
Battery
Terminal
Wires
3. Grasp door by both sides and ease it upward off of the lower
bracket (see Figure 49, page 22).
Battery
Clip
4. To replace glass door, follow the above instructions in reverse.
Figure 45 - Installing Battery in Receiver
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Removing/Replacing Glass Door (Cont.)
Installing Logs, Lava Rock and Glowing Embers
22
STOVE AND DIRECT-VENT
BURNER SYSTEM INSTALLATION
Continued
Bolt
4. Place log #3 (left piece) onto the front left part of the grate.
Make sure it is seated properly over the prong of the grate as
shown in Figure 52.
5. Place log #4 (right piece) onto the front right part of the grate
making sure the notches fit over the prong of the grate (see
Figure 53).
6. Place lava rock along sides and front of inside of burner system
bottom. It is not necessary to use all of the lava rock provided.
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner could cause
performance problems.
Bolt
Stove Front Panel
Figure 48 - Removing Front Panel from Stove
2
1
Screw
Glass
Door
Figure51-InstallingLogNo. 2
Figure 50 - Installing Log No. 1
Figure 49 - Removing Glass Door from Burner System Insert
4
3
INSTALLING LOGS, LAVA ROCK AND
GLOWING EMBERS
WARNING: Failure to position the parts in accor-
dancewiththesediagramsorfailuretouseonlyparts
specifically approved with this burner system may
result in property damage or personal injury.
Each log is marked with a number. These numbers will help you
identify the log when installing. It is very important to install these
logs exactly as instructed. Do not modify logs. Only use logs
supplied with freestanding burner system. Do not use if any log(s)
are broken (see Replacement Parts, page 31).
Figure 53 - Installing Log No. 4
Figure 52 - Installing Log No. 3
1. Remove glass door. See Removing/Replacing Glass Door, pages
21 and 22.
2. Place log #1 (back log) on top of grate. Make sure the notches
in the bottom of the log fit over the grate (see Figure 50).
3. Rest log #2 (large front log) on the pins on the front part of the
grate (see Figure 51).
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
STOVE AND DIRECT-VENT BURNER SYSTEM INSTALLATION
Installing Logs, Lava Rock, and Glowing Embers (Cont.)
OPERATING STOVE WITH BURNER SYSTEM
For Your Safety Read Before Lighting
23
LIghting Instructions
STOVE AND DIRECT-VENT
OPERATING STOVE WITH
BURNER SYSTEM
BURNER SYSTEM
INSTALLATION
FOR YOUR SAFETY
READ BEFORE LIGHTING
Continued
7. Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the ex-
posed section of the front burner and along the space between
the burner and grate prongs (see Figure 54). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember ma-
terial in one area. It is not necessary to use all of the ember
material provided.
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
8. Replace the glass door and stove front. See Removing/Replac-
ing Glass Door, pages 21 and 22.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
WARNING: The glass door must be securely in
place before running this burner system. Do not run
this burner system if glass is missing or broken.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone
in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
LIGHTING
INSTRUCTIONS
Figure 54 - Placing Ember Material on Burner
1. STOP! Read the safety information above.
2. Open lower panel.
3. Turn ON/OFF switch to “OFF”.
4. Turn off all electric power to the burner system.
5. Push in gas control knob slightly and turn clockwise
to “OFF”.
6. Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.
7. The pilot is located by the main burner and should not
require accessing for lighting.
8. Turn gas control knob counterclockwise
to “PILOT”.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING STOVE WITH BURNER SYSTEM
LIghting Instructions (Cont.)
24
To Turn Gas Off To Appliance
Manual Lighting Procedure
Optional Remote Operation
OPERATING STOVE WITH
BURNER SYSTEM
Continued
9. Push in gas control knob all the way and hold. Immedi-
ately light the pilot by repeatedly depressing the piezo spark
ignitor until a flame appears. Continue to hold for about
one (1) minute after the pilot is lit. Release gas control knob
and it will pop back. Pilot should remain lit. If it goes out,
repeat steps 5 through 8, page 23.
MANUAL LIGHTING
PROCEDURE
1. Remove glass door (see Removing/Replacing Glass Door,
pages 21 and 22).
2. Follow steps 1 through 8 under Lighting Instructions,
• If gas control knob does not pop up when released, stop and
immediately call your service technician or gas supplier.
• If the pilot will not stay lit after several tries, turn the gas
control knob to “OFF” and call your service technician
or gas supplier.
page 23.
3. Depress gas control knob and light pilot with match.
4. Keep gas control knob pressed in for 30 seconds after light-
ing pilot. After 30 seconds, release gas control knob. Now
follow steps 10 through 14, column 1.
10. Turn gas control knob counterclockwise
11. Turn on all electric power to the burner system.
12. Turn the ON/OFF switch to ON position.
to “ON”.
5. Replace glass door (see Removing/Replacing Glass Door,
pages 21 and 22).
OPTIONAL REMOTE
OPERATION
13. This valve is equipped with a HI/LO feature. Set burner
system input as desired.
14. Close lower panel.
Note: All remote control accessories must be purchased sepa-
rately (see Accessories, page 36). Follow instructions included
with the remote control.
TO TURN OFF GAS
TO APPLIANCE
Thermostat Control Operation
(Optional CGHRCTA Only) The thermostat control setting on
the remote control unit can be set to any comfort level between
HI and LO. The burners will turn on and off automatically to
maintain the comfort level you select. The ideal comfort setting
will vary by household depending upon the amount of space to
be heated, the output of the central heating system, etc.
1. Open lower panel.
2a. Turn ON/OFF switch to “OFF”.
2b. If Using Optional Hand-Held Remote: Set selector switch
in the OFF position to prevent draining battery.
3. Turn off all electrical power to the appliance if service is to
be performed.
NOTICE: You must light the pilot before using the
hand-held remote control unit. See Lighting Instruc-
tions, pages 23 and 24.
4. Push in gas control knob slightly and turn clockwise
to “OFF”.
5. Close lower panel.
1. After lighting, let pilot flame burn for about one minute.
Turn gas control knob on the control valve to ON position.
Turn variable control knob anywhere between HI and LO.
Slide the selector switch to the REMOTE position. Note:
The burners may light if hand-held remote ON button was
on when selector switch was last turned off. You can now
turn the burners on and off with either optional hand-held
remote control unit.
Shutting Off Burners Only (pilot stays lit)
You may shut off the burners and keep the pilot lit by doing one
of the following:
1. Turn gas control knob clockwise
position.
to the PILOT
2. Set selector switch in the OFF position.
Variable
Control Knob
IMPORTANT: Do not leave the selector switch in the RE-
MOTE position when the pilot is not lit. This will drain the
battery.
Piezo
Ignitor
Gas Control Knob
IMPORTANT: Be sure to press the ON/OFF buttons on the
hand-held remote control unit for up to 3 seconds to assure
proper operation.
LO
OUT
IN
Figure 55 - Control Valve
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING STOVE WITH BURNER SYSTEM
Optional Remote Operation (Cont.)
25
Operating Optional Blower Accessory
OPERATING STOVE WITH
BURNER SYSTEM
Continued
CGHRC Series Operation:
2a. Press the ON/OFF button to turn the burners on and off.
When turning burners off, the pilot will remain lit.
Shows
Temperature
Setting
Increases Room
Temperature in
AUTO Mode
CGHRCTA Series Operation:
Decreases Room
Temperature in
AUTO Mode
2b. Press the AUTO/ON/OFF button on the hand-held remote
control (see Figure 57). The lights to the left of the button
will show AUTO, ON, or OFF.
The Log Heater
will Automatically
Cycle between
Pilot and the Heat
Setting that has
been Selected
Turns Burners On
or Off and Allows
You to Choose the
Auto Setting
• In the ON mode, the burners will ignite. The heater is in
manual mode when ON is lit.
• In the AUTO mode, the thermostat in the hand-held re-
mote unit controls the room temperature. To increase the
room temperature, press the top arrow of the TEMP but-
ton. To lower the room temperature, press the bottom
arrow of the TEMP button. At higher settings the heater
will run longer.
IMPORTANT: This remote control has been specially
engineered to take an air temperature sample every 5.5
minutes in the auto mode. It will not respond immedi-
ately to the temperature setting being turned up or down.
IMPORTANT: The hand-held remote control unit must
Figure 57 - Hand-Held Thermostat Remote Control Unit
Selections (CGHRCTA Only)
OPERATING OPTIONAL
BLOWER ACCESSORY
be near the heater. Do not keep the hand-held remote Locate the blower controls by opening the lower door on the
control unit too close to the heater. The thermostat on
the hand-held remote control unit will heat up too quickly
and turn the fireplace off.
stove. Blower controls are located on the left side of the switch
bracket to the left just inside the door.
Both the GA3700 manual blower and the DA3610T thermo-
statically-controlled blower have an ON setting and an OFF
setting. The blower will only run when the switch is in the ON
3. To turn the burner off, press the AUTO/ON/OFF button
until OFF lights. The pilot will remain lit.
IMPORTANT:To turn the pilot off, manually turn the con- position. In the OFF position, the blower will not operate.
trol knob on the heater to the OFF position.
Note for DA3610T Only: If you are using DA3610T blower
with optional thermostat (wall mount or remote control) for the
burner system, your burner system and blower will not turn on
and off at the same time. The burner system may run for several
minutes before the blower turns on. After the burner system
modulates to the pilot position, the blower will continue to run.
The blower will shut off after the burner system temperature
decreases.
Selector Switch in Remote
Position (Optional Remote
Control)
Gas Control Knob
in On Position
Variable
Control Knob
LO
IN
OUT
The blower helps distribute heated air from the burner system.
Periodically check the air passageways of the burner system
andremoveanydust,dirt,orotherobstructionsthatwill hinder
the flow of air.
Figure 56 - Setting the Selector Switch, Gas Control Knob, and
Variable Control Knob for Remote Operation
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING STOVE WITH BURNER SYSTEM
Operating Optional GWMT1 Wall Mounted Thermostat
INSPECTING BURNERS
26
Pilot Assembly
Burner Flame Pattern
OPERATING STOVE WITH
BURNER SYSTEM
Continued
Thermopile
OPERATING OPTIONAL GWMT1
WALL MOUNTED THERMOSTAT
3/8" to 1/2"
Pilot Burner
1/8"
WARNING: Do not connect the thermostat to a
power source. Electrical shock and/or a fire hazard
will occur.
Piezo Ignitor
Thermocouple
Light the burner system as instructed in Lighting Instructions
on pages 23 and 24. Set wall thermostat to desired temperature.
Thisthermostathasbeenelectronicallycalibratedatthefactory
and requires no adjustment or leveling.
Upon installation, the thermostat must be allowed to stabilize at
room temperature for a minimum of 30 minutes for proper
operation.
Figure 58 - Pilot Assembly
BURNER FLAME PATTERN
To turn the burner system off, adjust thermostat to the lowest
setting and turn the gas control knob back to PILOT. The pilot
will remain lit.
Burner flames will be steady; not lifting or floating. Flame patterns
will be different from unit to unit and will vary depending on
installation type and weather conditions.
IMPORTANT: To turn the pilot off, turn the gas control knob
on the burner system to the OFF position.
If the vent configuration is installed incorrectly, the flames will lift
or "ghost". This can be dangerous. Inspect the flames after installa-
tion to ensure proper installation and performance.
INSPECTING BURNERS
Check pilot flame pattern and burner flame patterns often.
PILOT ASSEMBLY
Figure 59 shows a typical flame pattern. If burner flame pattern
differs from that described:
• turn burner system off (see To Turn Off Gas to Appliance, page 24)
• see Troubleshooting, pages 27 through 29
The pilot assembly is factory preset for the proper flame height.
Alterations may have occurred during shipping and handling. Call
a qualified service person to readjust the pilot if necessary.
The height of the thermopile must be 3/8" to 1/2" above the pilot
flame as shown in Figure 58. The thermocouple must be at a height
of about 1/8" above the pilot flame. The flame from the pilot burner
must extend beyond both the thermocouple and thermopile.
If your pilot assembly does not meet these requirements:
• turn burner system off (see To Turn Off Gas to Appliance, page 24)
• see Troubleshooting, pages 27 through 29
Figure 59 - Typical Flame Pattern
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEANING AND MAINTENANCE
Glass Door
27
Pilot and Burners
Logs
Venting System
CLEANING AND
MAINTENANCE
If glass has been broken, carefully remove glass door (see Remov-
ing/Replacing Glass Door, pages 21 and 22). Vacuum all glass
pieces with a shop vac.
WARNING: Turn off burner system and let cool
before cleaning.
CAUTION: Do not vacuum if pieces are hot.
CAUTION: You must keep control areas, burners,
and circulating air passageways of burner system
and stove clean. Inspect these areas of burner sys-
tem and stove before each use. Have burner system
and stove inspected yearly by a qualified service
person. Burner system and stove may need more
frequent cleaning due to excessive lint from carpet-
ing, bedding material, pet hair, etc.
Use only the ceramic glass door replacement intended for this burner
system (see Replacement Parts, page 31 for detail on ordering). No
substitutions may be made. See Removing/Replacing Glass Door,
pages 21 and 22 for instructions for replacing glass door.
WARNING:Donotoperateburnersystemwiththe
glass door removed, cracked, or broken.
GLASS DOOR
PILOT AND BURNERS
• Remove ember material before cleaning burners and replace
when cleaning is complete.
WARNING:Handleglassdoorpanelwithcare. Do
not strike, slam, or otherwise abuse glass. Do not
operate burner system with the glass door removed,
cracked, or broken.
• Burner and controls should be cleaned with compressed air to
remove dust, dirt, or lint.
• Use a vacuum cleaner or small, soft bristled brush to remove
excess dust, dirt, or lint.
WARNING: Do not use abrasive cleaners as this
maydamageglass.Useanonabrasivehouseholdglass
cleaner to clean glass. Do not clean glass when hot.
LOGS
• If you remove logs for cleaning, refer to Installing Logs, Lava
Rock, and Glowing Embers, pages 22 and 23, to properly re-
place logs.
Glass must be cleaned periodically. During start-up it is normal for
condensationtoformontheinsideoftheglasscausinglint,dust,and
other airborne particles to cling to the glass surface. During initial
start-up a slight film may form on the glass due to paint curing. The
glass should be cleaned several times with a non-ammonia, non-
abrasivehouseholdcleanerandwarmwaterafterthefirsttwoweeks
of operation. Thereafter, clean the glass two or three times during
each heating season, depending on the usage and circumstances
present. Refer to Removing/Replacing Glass Door on pages 21 and
22 of this manual when removing glass door for cleaning.
• Use a vacuum cleaner to remove any carbon buildup on logs.
• Replace log(s) if broken. See Replacement Parts on page 31.
• Replace ember material periodically as needed. See Replace-
ment Parts on page 31.
VENTING SYSTEM
Conduct annual inspection of the venting system following these
guidelines:
1. Check areas of venting system that are exposed to the weather for
corrosion (rust spots or streaks and, in extreme cases, holes). Have
these items replaced immediately by a qualified service person.
WARNING: Only parts supplied by the manufac-
turer should be used when replacing broken or dam-
aged glass door panel (see Replacement Parts, page
36). This glass door panel is a complete unit. No
substitute materials may be used.
2. Remove the vent cap and shine a flashlight into the vent. Re-
move any foreign material.
3. Check for evidence of excessive condensation. Continuous
condensation can cause corrosion of caps, pipes, and fittings
and can be caused by having excessive lateral runs, too many
elbows, or exterior portions of the system being exposed to
cold weather.
CAUTION: Wear gloves and safety glasses while
handling or removing broken glass. Do not remove if
glass is hot. Keep children and pets away from glass.
4. Inspect joints to verify that no pipe section or fitting has been
disturbed and loosened. Check mechanical supports such as
wall straps for rigidity.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
28
TROUBLESHOOTING
Note: For additional help, visit DESA
International’s technical service web
WARNING: Turn off burner sys-
temandletcoolbeforeservicing.Only
a qualified service person should ser-
viceandrepairburnersystemorstove.
CAUTION: Never use a
wire, needle, or similar ob-
ject to clean pilot. This can
damage pilot unit.
Note:Alltroubleshootingitemsarelistedin
order of operation.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
When ignitor button is pressed, there is no
spark at pilot
1. Ignitor electrode not connected to igni- 1. Reconnect ignitor cable
tor cable
2. Ignitor cable pinched or wet
2. Free ignitor cable if pinched by any
metal or tubing. Keep ignitor cable dry
3. Tighten nut holding piezo ignitor. Nut
is located behind the mounting bracket
4. Replace ignitor cable
3. Piezo ignitor nut is loose
4. Broken ignitor cable
5. Bad piezo ignitor
5. Replace piezo ignitor
6. Ignitor electrode broken
7. Ignitor electrode positioned wrong
6. Replace pilot assembly
7. Replace pilot assembly
When ignitor button is pressed, there is
spark at pilot but no ignition
1. Gas supply turned off or equipment 1. Turn on gas supply or open equipment
shutoff valve closed shutoff valve
2. Gas control knob not in PILOT position 2. Turn gas control knob to PILOT position
3. Gas control knob not pressed in while 3. Press in gas control knob while in PILOT
in PILOT position
position
4. Air in gas lines when installed
4. Continue holding down gas control
knob. Repeat igniting operation until air
is removed
5. Depleted gas supply (propane/LP mod- 5. Contact local propane/LP gas company
els only)
6. Pilot is clogged
6. Clean pilot (see Cleaning and Mainte-
nance, page 27) or replace pilot assembly
7. Replace gas control
7. Gas regulator setting is not correct
Pilot lights but flame goes out when control
knob is released
1. Gas control knob not fully pressed in
2. Gas control knob not pressed in long 2. After pilot lights, keep gas control knob
1. Press in gas control knob fully
enough pressed in 30 seconds
3. Equipment shutoff valve not fully open 3. Fully open equipment shutoff valve
4. Pilot flame not touching thermocouple, 4. A) Contact local gas company
which allows thermocouple to cool,
causing pilot flame to go out. This prob-
lem could be caused by one or both of
the following:
B) Clean pilot (see Cleaning and
Maintenance, page 27) or replace pilot
assembly
A) Low gas pressure
B) Dirty or partially clogged pilot
5. Thermocouple connection loose at con- 5. Hand tighten until snug, then tighten
trol valve
1/4 turn more
6. Thermocouple damaged
6. Replace pilot assembly
7. Control valve damaged
7. Replace control valve
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
29
TROUBLESHOOTING
Continued
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner does not light after pilot is lit
1. Burner orifice clogged
1. Clean burner (see Cleaning and
Maintenance, page 27) or replace burner
orifice
2. Inlet gas pressure is too low
2. Contact local propane/LP or natural gas
company
3. Thermopile leads disconnected or im- 3. Reconnect leads (see Wiring Diagram,
properly connected
page 31)
4. Thermopile is defective
4. Replace thermopile
Delayed ignition burner
1. Manifold pressure is too low
1. Contact local propane/LP or natural gas
company
2. Burner porting or orifice clogged
2. Clean burner (see Cleaning and Main-
tenance, page 27) or replace burner orifice
Burner backfiring during combustion
1. Burner orifice is clogged or damaged
1. Clean burner (see Cleaning and
Maintenance, page 27) or replace burner
orifice
2. Damaged burner
2. Replace damaged burner
3. Gas regulator defective
3. Replace gas control
Slight smoke or odor during initial operation 1. Residues from manufacturing processes 1. Problem will stop after a few hours of
and logs curing operation
Burner system produces a whistling noise 1. Turning gas control knob to HI position 1. Turn gas control knob to LO position and
when burner is lit
when burner is cold
let warm up for a minute
2. Air in gas line
2. Operate burner until air is removed from
line. Have gas line checked by local pro-
pane/LP or natural gas company
3. Dirty or partially clogged burner orifice 3. Clean burner (see Cleaning and
Maintenance, page 27) or replace burner
orifice
Glass soots
1. Flame impingement on logs
2. Debris around burner air mixer
1. Adjust the log set so that the flame does
not excessively impinge on it
2. Inspect the opening at the base of the
burner to see that it is NOT packed with
any type of material
Burner system produces a clicking/ticking 1. Metal expanding while heating or con- 1. This is common. If noise is excessive,
noise just after burners are lit or shut off
tracting while cooling
contact qualified service person
Remote does not function
1. Battery is not installed or battery power 1. Replace 9-volt batteries in receiver and
is low remote control
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
30
TROUBLESHOOTING
Continued
WARNING: If you smell gas
• Shut off gas supply.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor’s phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas supplier, call the fire department.
IMPORTANT: Operating burner system where impurities in air exist may create odors. Cleaning
supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc., create
fumes. These fumes may mix with combustion air and create odors. These odors will disappear over time.
OBSERVED PROBLEM
POSSIBLE CAUSE
REMEDY
Burner system produces unwanted odors
1. Gas leak. See Warning statement 1. Locate and correct all leaks (see Check-
above
ing Gas Connections, pages 19 and 20)
Burner system shuts off in use
1. High or gusting winds
1. Burner system has been tested for up to
40mph winds. However, extreme con-
ditions may occur. See Lighting Instruc-
tions on pages 23 and 24
2. Low line pressure
2. Contact local propane/LP or natural gas
company
3. Pilot is partially clogged
3. Clean pilot (see Cleaning and Mainte-
nance, page 27)
4. Inner vent pipe leaking exhaust gasses 4. Locate and correct all leaks (see Check-
into system ing Gas Connections, pages 19 and 20)
5. Glass too loose and air tight gasket leaks 5. Tighten glass
in corners after usage
6. Bad thermopile or thermocouple
7. Improper vent cap installation
6. Replace faulty component
7. Check for proper installation and free-
dom from debris or blockage
Gas odor even when control knob is in OFF 1. Gas leak. See Warning statement 1. Locate and correct all leaks (see Check-
position
above
ing Gas Connections, pages 19 and 20)
2. Control valve defective
2. Replace control valve
Gas odor during combustion
1. Gas leak. See Warning statement 1. Locate and correct all leaks (see Check-
above
ing Gas Connections, pages 19 and 20)
Dark residue on logs or inside of burner 1. Improper log placement
system
1. Properly locate logs (see Installing Logs,
Lava Rock, and Glowing Embers, pages
22 and 23)
2. Air holes at burner inlet blocked
3. Burner flame holes blocked
2. Clean out air holes at burner inlets. Pe-
riodically repeat as needed
3. Remove blockage
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
WIRING DIAGRAM
SPECIFICATIONS
REPLACEMENT PARTS
31
WIRING DIAGRAM
CAUTION: Label all wires prior to disconnection
when servicing controls. Wiring errors can cause
improper and dangerous operation. Verify proper
operation after servicing.
REPLACEMENT PARTS
Note: Use only original replacement parts. This will protect your
warranty coverage for parts replaced under warranty.
PARTS UNDER WARRANTY
Contact authorized dealers of this product. If they can not supply
original replacement part(s), call DESA International’s Technical
Service Department at 1-866-672-6040.
Variable
Fan Switch
Fan Switch
(N.O.)
When calling DESA International, have ready
• your name
• your address
1
Off
Black
2
• model and serial numbers of your burner system and stove
• how burner system or stove was malfunctioning
• type of gas used (propane/LP or natural gas)
• purchase date
On
Blue
110/115
V.A.C.
Usually, we will ask you to return the part to the factory.
Black
White
Green
Blower
Motor
PARTS NOT UNDER WARRANTY
Contact authorized dealers of this product. If they can not
supply original replacement part(s), call DESA International at
1-866-672-6040 for referral information.
When calling DESA International, have ready
• model number of your burner system and stove
• the replacement part number
Figure 60 - Blower Wiring Diagram for Thermostat-Controlled
Models
SPECIFICATIONS
CDVBN(A)
CDVBP(A)
14,000-20,000 Btu/hr
Propane/LP
Piezo
16,000-22,000 Btu/hr
Gas Type
Natural
Piezo
Ignition
Manifold Pressure
Minimum Inlet Supply Pressure
Thermal Efficiency
3.5" w.c.
4.5" w.c.
70%
10.0" w.c.
11.0" w.c.
70%
Dimension, Inches/mm (HxWxD)
Stove and Burner System*
26 1/2" x 25" x 25 5/8"
26 1/2" x 25" x 25 5/8"
673.1 x 635 x 650.7mm
23 1/4" x 33 1/4" x 23 1/2"
590.5 x 844.5 x 596.9mm
673.1 x 635 x 650.7mm
23 1/4" x 33 1/4" x 23 1/2"
590.5 x 844.5 x 596.9mm
Carton (Insert Only)
Weight, lbs/kg
Burner System
70 lbs/31.8 kg
75 lbs/34 kg
70 lbs/31.8 kg
75 lbs/34 kg
Shipping
* When installed in Comfort Glow cast iron stove body (CISGA Series and CISCA Series).
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS BREAKDOWN
Models CDVBNC and CDVBPC
32
ILLUSTRATED PARTS
BREAKDOWN
MODELS CDVBNC AND CDVBPC
3
29
32
12
27
25
26-1
26-2
1
4
19
23
20
21
9
4
26-3
26-4
8
10
31
4
13
11
14
28
16
6
5
28
30
24
18
15
2
17
22
22
7
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
33
Models CDVBNC and CDVBPC
PARTS LIST
MODELS CDVBNC AND CDVBPC
This list contains replaceable parts used in your burner system.
When ordering parts, follow the instructions listed under Replace-
ment Parts on page 31 of this manual.
KEY
NO.
PART NUMBER
DESCRIPTION
QTY.
1
2
3
4
5
6
7
8
**
Firebox Assembly
Screw, Hex
Rear Cover
Screw, Hex
Switch Plate
On/Off Switch
Wire Harness
Relief Cover
Relief Cover Gasket
Relief Spring
Relief Washer
Hex Head Cap Screw
Locknut
Valve Bracket
Valve, Natural
Valve, Propane/LP
Pilot Assembly, Natural
Pilot Assembly, Propane/LP
Ignitor, Piezo
Palnut Fastener
Burner, Natural
Burner, Propane/LP
Orifice, Natural
Orifice, Propane/LP
Brass Elbow
1
2
1
12
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
18
4
2
1
1
M11084-26
27129
M11084-39
103587-02
099998-01
103284-04
104491-01
104518-01
104527-01
104528-01
H5C4-20B
NTC-4C
105468-02
14389
14390
14561
14562
102445-01
102334-01
105523-01
105523-02
104506-01
104506-02
14528
901056-01
105493-01
105795-01
105325-01
14585
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Brass Elbow
Aluminum Tubing Assy
Glass Door Assy
Air Deflector
Log Set
Rear Log
26-1 105773-01
26-2 105773-02
26-3 105773-03
26-4 105773-04
27
28
29
30
31
Front Log
Left Log Piece
Right Log Piece
Screw
Screw
Screw
M10908-2
11107
M12461-62
104555-03CJ
105483-01
Grate Assembly
Burner Bracket
PARTS AVAILABLE - NOT SHOWN
GA6060
14250
M11084-3
Lava Rock
Ember Material
Hex Screw for Blower Bracket
1
1
4
** Not a field replaceable part.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
ILLUSTRATED PARTS BREAKDOWN
Models CISC and CISG
34
ILLUSTRATED PARTS
BREAKDOWN
STOVE CHASSIS
MODELS CISC AND CISG
1
6
5-4
4
5-4
4
5-1
2
3
5-2
5-3
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS LIST
35
Models CISC and CISG
PARTS LIST
MODELS CISC AND CISG
This list contains replaceable parts used in your stove. When
ordering parts, follow the instructions listed under Replacement
Parts on page 31 of this manual.
KEY PART
NO.
NO.
DESCRIPTION
QTY.
1
2
104968-01
104969-01
104969-02
104174-03
104970-01
104970-02
104971-01
*
Stove Back Panel (Black Only)
Bottom Door (Charcoal)
Bottom Door (Forest Green)
1
1
1
1
1
1
1
1
3
4
Stove Dropped Bottom
One Leg (Charcoal) (4 Total Per Stove)
One Leg (Forest Green) (4 Total Per Stove)
Hardware Kit
Door Hinge Step Bolt With Shoulder (1 Per Unit)
Door Catch Bolt M8 x 1.25 - 55mm Long With Two M8
Hex Nuts (1 Per Unit)
Bottom Floor Bolts M6 x 1 - 25mm Long With Flat Washer
And Lock Washer (4 Per Unit)
Leg Attachment Stud, Headless, Slotted,
M10 x 1.5 - 40mm Long
Back Panel Bolts M6 x 1 - 20mm Long With Flat Washer
And Lock Washer (6 Per Unit)
5
5-1
5-2
*
1
1
4
1
5-3
5-4
7
*
*
104178-01
PARTS AVAILABLE — NOT SHOWN
104108-08
104108-05
Touch-up Spray Paint 12 oz Can (Charcoal)
Touch-up Spray Paint 12 oz Can (Forest Green)
1
1
* Included In Hardware Kit
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL SERVICE
SERVICE HINTS
ACCESSORIES
36
TECHNICAL SERVICE
You may have further questions about installation, operation, or
troubleshooting. If so, contact DESA International’s Customer
Service Department at 1-866-672-6040. When calling, please have
your model and serial numbers of your heater ready.
You can also visit DESA International’s technical service web site
RECEIVER AND HAND-HELD REMOTE
CONTROL KIT - CGHRC SERIES
SERVICE HINTS
When Gas Pressure Is Too Low
For all models. Allows the burner system to be turned on and off
conveniently.
• pilot will not stay lit
• burners will have delayed ignition
W
A
R
M
E
R
C
O
T
O
E
M
P
LE
• burner system will not produce specified heat
• propane/LP gas supply might be low (propane/LP units only)
R
A
U
TO
O
N
O
FF
If you feel your gas pressure is too low or gas quality is bad, contact
your local natural or propane/LP gas supplier.
RECEIVER AND HAND-HELD THERMOSTAT
REMOTE CONTROL KIT - CGHRCTA
ACCESSORIES
Purchase these stove and burner system accessories from your local
dealer. If they can not supply these accessories, call DESA
International’s Sales Department at 1-866-672-6040. for informa-
tion. You can also write to the address listed on the back page of this
manual.
For all models. Allows the burner system to be operated in a
manually or thermostatically-controlled mode. You can adjust your
heatsettingsandturntheburnersystemonoroffwithoutleavingthe
comfort of your easy chair. (Requires part no. 103284-04 wire
harness included with burner system.)
MANUAL BLOWER KIT - GA3750
For all models. Manual-variable control blower accessory for both
the CDVBN(A) and CDVBP(A) Series burner systems.
THERMOSTATICALLY- CONTROLLED
BLOWER KIT - CDA3620TB
For all models. Provides better heat distribution. Blower turns off
and on automatically, as needed. Complete installation and opera-
tion instructions included in this manual.
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER'S REGISTRATION FORM
In order to provide better customer service for this and future purchases, we recommend that you register your product with us.
You can register online at www.desatech.com. If access to our website is not available to you, please complete this Owner’s
Registration Form and mail to the address on the back of this owner’s manual. Please provide the following product information:
Brand:
(Comfort Glow, Vanguard, etc.)
Model:
(EFP33PR, VTGH33NR, etc.)
Date Purchased:
Serial Number:
First Name:
Address:
Note: Keep receipt for warranty verification.
7 or 9 digit number located on product or identification tag.
Last Name:
City:
State:
Zip:
Country:
Home Phone:
E-Mail:
(
)
-
Please answer the following questions to register your product with DESA International:
1. Where will the product be used?
❍❍Living/Family Room ❍❍Office/Warehouse ❍❍Utility Shed/Outbuilding ❍❍Garage ❍❍Bedroom ❍❍Bathroom ❍❍Other
2. If you bought this product yourself, did you plan to purchase this type of product before going into the store? ❍❍Yes ❍❍No
3. Who selected the product? ❍ Male ❍ Female ❍ Both
4. What is the population of your area? ❍❍Under 10,000 ❍❍10,000 to 25,000 ❍ 25,000 to 50,000 ❍❍50,000 to 100,000
❍❍100,000 to 250,000 ❍❍Over 250,000
5. What is your primary source of heat? ❍❍Propane (LP Gas) ❍❍Fuel Oil ❍❍Wood ❍❍Natural Gas ❍❍Electric ❍❍Other
6. How was the product installed? ❍❍Professional Installer ❍❍Self ❍❍Other
7. Cost of product excluding sales tax? $___________________
8. Cost to install product? $____________________
9. Type of store where product was purchased? ❍❍Hardware ❍❍Propane Dealer ❍❍Natural Gas/Utility Co. ❍❍Home Center/Builder’s Supply
❍❍Fireplace or Hearth Shop ❍❍Farm Store ❍❍Other
10. What motivated you to buy this product? ❍❍Sudden Cold Weather ❍❍Replace Older Model ❍❍D.I.Y. Home Project
❍❍Emergency Back-Up Heat ❍❍Heater was on Sale ❍❍Energy Savings/High Efficiency ❍❍Construction Project ❍❍Other
11. How did you learn about this product brand? ❍❍Advertising ❍❍Relative or Friend ❍❍Store Display ❍❍Other ________________________
12. Level of Education of Purchaser: ❍❍Some High School ❍❍Completed High School ❍❍Completed College ❍❍Completed Graduate School
13. Age of Purchaser: ❍❍Under 20 ❍❍20 - 29 ❍❍30 - 39 ❍❍40 - 49 ❍❍50 - 59 ❍❍60 or Over
14. Buyer’s total annual household income: ❍❍Under $15,000 ❍❍$15,000 to $19,999 ❍❍$20,000 to $34,999 ❍❍$35,000 to $49,999
❍❍$50,000 to $74,999 ❍❍$75,000 to $99,999 ❍❍$100,000 and Over
15. Store where product was purchased:
Name: ______________________________________
City: _______________________ State: __________
16. In choosing this product, how important were the following:
Not Important
Somewhat Important
Very Important
Availability
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
❍
Price
Brand Name
Overall Quality
Heat Output
Made in USA
Warranty
Local Service
Value for Price
Prior Brand Experience
Controls Location
Thermostat, Remote, or Manual Operation
Ease of Operation
Special Features
Salesperson’s Recommendation
Friend/Relative’s Recommendation
❍❍
Portability
❍
❍
❍
❍
Quiet Operation
❍
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
39
NOTES
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
_______________________________________________________________________________________________
105501-01G
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY INFORMATION
KEEP THIS WARRANTY
Model
Serial No.
Date Purchased
Always specify model and serial numbers when communicating with the factory.
We reserve the right to amend these specifications at any time without notice. The only warranty applicable is our standard written warranty. We
make no other warranty, expressed or implied.
COMFORT GLOW LIMITED WARRANTY
DIRECT-VENT BURNER SYSTEM AND STOVE CHASSIS
DESA International warrants this product to be free from defects in materials and components for two (2) years from the date of first purchase,
provided that the product has been properly installed, operated and maintained in accordance with all applicable instructions. To make a claim under
this warranty the Bill of Sale or cancelled check must be presented.
Thiswarrantyisextendedonlytotheoriginalretailpurchaser. Thiswarrantycoversthecostofpart(s)requiredtorestorethisstoveandburnersystem
to proper operating condition and an allowance for labor when provided by a DESA Authorized Service Center. Warranty part(s) MUST be obtained
through authorized dealers of this product and/or DESA International who will provide original factory replacement parts. Failure to use original
factory replacement parts voids this warranty. The stove and burner system MUST be installed by a qualified installer in accordance with all local
codes and instructions furnished with the unit.
This warranty does not apply to parts that are not in original condition because of normal wear and tear, or parts that fail or become damaged as a result
of misuse, accidents, lack of proper maintenance or defects caused by improper installation. Travel, diagnostic cost, labor, transportation and any and
all such other costs related to repairing a defective stove and burner system will be the responsibility of the owner.
TO THE FULL EXTENT ALLOWED BY THE LAW OF THE JURISDICTION THAT GOVERNS THE SALE OF THE PRODUCT; THIS
EXPRESS WARRANTY EXCLUDES ANY AND ALL OTHER EXPRESSED WARRANTIES AND LIMITS THE DURATION OF ANY AND
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
TO TWO (2) YEARS ON ALL COMPONENTS FROM THE DATE OF FIRST PURCHASE; AND DESA INTERNATIONAL’S LIABILITY
ISHEREBYLIMITEDTOTHEPURCHASEPRICEOFTHEPRODUCTANDDESAINTERNATIONALSHALLNOTBELIABLEFORANY
OTHER DAMAGES WHATSOEVER INCLUDING INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow a limitation on how long an implied warranty lasts or an exclusion or limitation of incidental or consequential damages,
so the above limitation on implied warranties, or exclusion or limitation on damages may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
For information about this warranty write:
TM
2701 Industrial Drive
P.O. Box 90004
Bowling Green, KY 42102-9004
105501-01
Rev. G
02/03
105501 01
NOT A UPC
1
Download from Www.Somanuals.com. All Manuals Search And Download.
|