In s t a l l a t Io n In s t r u c t Io n s
Wa r m In g ov e n
For use with models:
EW, EWO
MW, MWO
PW, PWO
IWO, IOWO
Part No. 65034 Rev. K
Download from Www.Somanuals.com. All Manuals Search And Download.
Im p o r t a n t sa f e t y In s t r u c t Io n s
Safety Symbols and Labels
Im p o r t a n t In f o r m a t Io n ab o u t
DANGER
sa f e t y In s t r u c t Io n s
Immediate hazards that WILL result in severe personal injury or
death.
Important Safety Instructions and warnings appearing in these
instructions are not meant to cover all possible conditions and
situations that can occur. Common sense, caution and care
must be exercised when installing, maintaining or operating an
appliance.
WARNING
Hazards or unsafe practices that COULD result in severe
personal injury or death.
Installation should be done by a qualified installer.
CAUTION
Hazards or unsafe practices that COULD result in minor
personal injury or property damage.
Always contact Dacor about problems or conditions you do not
understand.
ge n e r a l sa f e t y pr e c a u t Io n s
To reduce the risk of fire, electric shock, serious injury or death when installing or using this appliance, follow basic safety
precautions, including the following:
WARNING
1. Read all instructions before using the appliance.
11. Keep the electrical cord away from heated surfaces.
2. This appliance must be grounded. Connect only
to a properly grounded outlet. See “Grounding
Instructions.”
12. Some products, such as whole eggs and sealed
containers such as closed glass jars may explode
and should not be heated in this oven.
3. Install or locate this appliance only in accordance
with these installation instructions.
13. To reduce the risk of fire in the oven cavity: Do not
overcook food. Carefully attend the appliance if
paper, plastic or other combustible materials are
placed inside the oven.
4. Use this appliance only for its intended use as
described in this manual. Do not use corrosive
chemicals or vapors in this appliance. This type of
oven is specifically designed to heat and cook food.
It is not designed for industrial or laboratory use.
14. If materials inside the oven should ignite, keep the
oven drawer closed and shut off the power at the fuse
or the circuit breaker panel.
15. Only model IOWO24 is approved for use in outdoor
applications and near water (bathrooms).
5. As with any appliance, close supervision is
necessary when used by children.
16. Model IOWO24, when installed as a towel warmer,
must have the wire rack (supplied with the product)
installed in the drawer bottom. Secure the rack with
with a screw and clip supplied with the rack.
6. Do not operate this appliance if it has a damaged
electrical cord or plug, if it is not working properly or
if it has been damaged or dropped.
7. This appliance should be serviced only by qualified
service personnel. Contact the nearest Dacor
Authorized Servicer at (800) 793-0093, or at www.
Dacor.com for examination, repair or adjustment.
8. Do not cover or block any openings on the
appliance.
9. Do not store or use this appliance outdoors, except
as noted in these instructions. Do not use this
product near water – for example, near a kitchen
sink, in a wet basement or near a swimming pool,
etc.
10. Do not immerse the electrical cord or plug in water.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
De s Ig n specIfIcatIons
pr o D u c t DIm e n s Io n s
NOTE: All tolerances are + 1/16,” - 0”
unless otherwise stated.
Overall Dimensions
(EW, EWO, MW, MWO, PW, PWO)
40" (1016mm)
3 prong
120 Vac power cord
9"
Mounting
holes
10 1/8"
(257mm)
1/2"
(13mm)
(229mm)
10"
(254mm)
Chassis view
without drawer
Drawer Face Dimensions
1/2"
(13mm)
(MW Shown)
Chassis Dimensions
EW
EWO
PWO
MWO
PW
MW
3 5/16"
(84mm)
2 3/16"
(56mm)
1 5/16"
(33mm)
3 7/16"
(87mm)
3 1/4"
(83mm)
2 1/4"
(57mm)
D
E
1"
(25mm)
1"
(25mm)
1"
(25mm)
1"
(25mm)
1 5/32"
(29mm)
1 1/8"
(29mm)
23 1/16"
(586mm)
Handle Dimensions
Chassis
“C” Drawer Face
Width
“D” Chassis Face
Width
Model
“E” Chassis Width
EWO24
EW27
23 7/8” (606mm)
23 11/16” (602mm)
22 3/16” (564mm)
5/64"
(2mm)
EWO27
MW27
23 13/16”
Drawer open
(605mm)
26 7/8” (683mm)
26 11/16” (678mm)
MWO27
PW27
EW30
25 3/16” (640mm)
EWO30
MW30
C
Overall Dimensions - Top View
29 7/8” (759mm)
35 7/8” (911mm)
29 11/16” (754mm)
35 11/16” (906mm)
MWO30
PW30
(EWO shown)
PWO30
EWO36
34 1/4” (870mm)
Warming Oven Overall Dimensions
2
Download from Www.Somanuals.com. All Manuals Search And Download.
De s Ig n specIfIcatIons
Overall Dimensions
(IWO, IOWO)
40" (1016mm)
3 prong
120 Vac power cord
Mounting holes
(rear holes IOWO model only)
F
K
C
Chassis view
without drawer
Drawer Face Dimensions
(IWO Shown)
Chassis Dimensions
(IOWO Shown)
E
G
Chassis
NOTE: Only model IOWO24 warming ovens are
approved for outdoor use. They are designed for
installation of a custom designed drawer front or for
the Dacor Epicure® drawer front and handle. Order
accessory model number AEWP24 through your
Dacor dealer.
J
Drawer open
C
Overall Dimensions
Top View
Dimension
“K”
Chassis
height
Warming
Oven
Model No.
Dimension “C”
Drawer face
width
Dimension “E”
Chassis face
width
Dimension “F”
Drawer face
height
Dimension
“G”
Chassis depth
Dimension “J”
Drawer depth
11 13/16”
(300mm)
19 3/4”
(502mm)
18 13/16”
(478mm)
11 7/8”
(302mm)
IOWO24
22 1/2” (572mm)
22 5/16” (567mm)
25 5/16” (643mm)
IWO24
IWO27
22 3/8” (568mm)
25 3/8” (645mm)
23 1/16”
(586mm)
23 13/16”
(605mm)
8 15/16” (227mm)
9” (229mm)
Integrated Warming Oven Overall Dimensions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
In s t a l l a t Io n specIfIcatIons
In s t a l l a t Io n pl a n n In g
◊
◊
◊
A qualified technician must complete the installation of this
built-in appliance. Proper installation is the responsibility of
the customer.
Carefully check the installation location. The oven should be
placed for convenient access. Make certain that electrical
power can be provided in the selected location.
27"/30"/36"
Dacor
single oven
1 ¾” Min.
(44mm)
Plan the installation so that all minimum clearances are
met or exceeded. Dimensions shown provide minimum
clearances, unless otherwise noted. Be certain that proper
clearance is provided for the oven door when it is in the open
position.
Warming Oven
Warming Oven
C
D
C
◊
◊
The specified minimum cabinet depth and width must be
provided. The cabinet depth and width must completely
enclose the recessed portion of the oven.
120 Vac
electrical
outlets
Cabinet cutout dimensions must be used as indicated. All
contact surfaces between the appliance and the cabinet must
be solid and level. The oven support platform must be flush
with the bottom edge of the cabinet cutout.
Toe Kick
A
5/8” Min.
(16mm)
◊
Make certain that you have everything necessary to ensure a
proper installation before proceeding.
Stacked Installation with Wall Oven
NOTES:
1. Minimum Cutout Depth:
Model IOWO24 - 20” (508mm)
All other models - 23 3/8” (594mm)
2. The IOWO24 and EWO36 models cannot be stacked.
3. The IOWO24 warming oven is not approved for
installation under a wall oven.
“B” Min. Width
to Adjacent
Doors/Drawers
“A” Cutout
Width
“C” Cutout
Height
“D” Min. Gap
Between Cutouts
Model
IOWO24
22 9/16” (573mm)
22 1/2” (572mm)
12 1/8” (308mm)
N/A*
N/A*
IWO24
EWO24
EW27
24 1/4” (616mm)
27 1/4” (692mm)
N/A*
1 1/16” (27mm)
N/A*
EWO27
IWO27
MW27
MWO27
PW27
27 1/4” (692mm)
9 1/8” (232mm)
25 1/2” (648mm)
EW30
EWO30
MW30
1 1/16” (27mm)
30 1/4” (768mm)
36 1/4” (921mm
MWO30
PW30
PWO30
EWO36
34 3/8” (873mm)
3” (76mm)
* Depends on size of cabinet face installed.
Table 1: Cutouts Dimensions
4
Download from Www.Somanuals.com. All Manuals Search And Download.
In s t a l l a t Io n specIfIcatIons
1 1/2" (38mm)
Typical countertop
Cooktop
3/4" Min.
(19mm)
Warming Oven
C
5/8" Min.
(16mm)
120 Vac
electrical
outlet
36" Typ.
(914mm)
A
B
Single Installation to Side of Cooktop
OB Outdoor Grill
EG Epicure Gas Cooktop
3/4" Min.
(19mm)
Warming Oven
C
C
36" typ.
(914mm)
D
120 Vac
electrical
outlet
Warming Oven
5/8" Min.
(16mm)
A
B
Stacked Installation Below Cooktop or Grill
5
Download from Www.Somanuals.com. All Manuals Search And Download.
In s t a l l a t Io n specIfIcatIons
The correct voltage, frequency and amperage must be supplied
to the electrical outlet from a grounded, single phase circuit that is
protected by a properly sized circuit breaker or time-delay fuse.
po W e r su p p l y re q u I r e m e n t s
WARNING
Electric shock Hazard – This appliance is equipped
with a 40” (1016mm) power cord with a three prong
grounded plug. Plug it only into a grounded three prong
electrical outlet.
Circuit Requirements:
◊
120 Vac, 60 Hz, 15 Amp. dedicated circuit.
Total Connected Load:
• Do not remove the ground prong.
• Do not use a 2-prong adapter.
• Do not use an extension cord.
◊
◊
Model EWO36: 0.8kW (6.5 Amp.)
All other models: 0.5kW (4 Amp.)
NOTES:
• Do not use a power cord that is frayed or
damaged.
1. The above specifications are for reference only. Refer
to the product date label for exact specifications. If the
requirements above do not agree with those listed on
the product data label, use the information found on the
label. See inside the front cover for location.
Failure to comply with the above can result in fire,
electric shock, or death.
The electrical outlet for this appliance must only be
installed by a licensed electrician.
2. If the electrical service provided does not meet the
product specifications, or does not conform to the NEC
or local standards, do not proceed with the installation.
Call a licensed electrician to install the required
electrical service before proceeding.
Power cord with
three-prong grounding plug
3. Be certain to locate the electrical outlet in an
accessible location, so that the warming oven may be
easily unplugged if service becomes necessary.
4. It is the owner’s responsibility to ensure that the
electrical outlet for this appliance has been installed
by a qualified electrician. The electrical installation
must comply with the latest revision of the National
Electric Code ANSI/NFPA 70 and local codes and
ordinances.
Grounding type
electrical outlet
In s t a l l In g t h e su p p o r t pl a t f o r m In
t h e ca b In e t
Chassis
face
Provide a platform (100lb. load capacity) within the cabinet upon
which the warming oven will be supported. The platform must
be installed level and straight. The top edge of the platform must
be flush with the cutout at the front of the cabinet. There are no
provisions to level the warming oven after it has been installed.
3/4” (19mm) thick plywood is recommended.
Support
platform
NOTE:
If the oven is not installed in a level fashion, the drawer
may slide open on its own or may not seal tightly, allowing
heat to escape and resulting in poor performance.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
In s t a l l a t Io n In s t r u c t Io n s
verIfyIng t h e pa c k a g e co n t e n t s
In s t a l l In g t h e ch a s s Is
• Use and care manual
WARNING
• Mounting screws
• Wire rack with mounting hardware (IOWO model only)
To avoid personal injury caused by the appliance
falling forward when the drawer is opened, secure
the chassis to the cabinet and support platform as
instructed.
re m o v In g t h e Dr a W e r
WARNING
1. Verify that the electrical outlet for the warming
oven meets the Power Supply Requirements on
the facing page before proceeding.
1. Grasp the warming oven chassis on opposite sides and
slide it partially into the cabinet opening.
2. Temporarily support the oven in place so that it will not
tilt or fall.
2. Be certain that power plug is disconnected from
the electrical outlet before installation.
3. From an adjoining cabinet, reach in behind the oven
and pull the power cord until the plug is next to the
electrical outlet. Do not plug in the power cord at this
time.
Remove the drawer from the appliance to allow access
to the mounting holes during installation, and to reduce
weight:
4. After positioning the power cord and plug, slide the
chassis completely into the cabinet until the front frame
is positioned flush against the cabinet face.
1. Pull the drawer out to the fully open position.
2. Push in on the locking tab on one side as you pull the
drawer up.
5. Use the screws provided to secure the warming oven
chassis to the cabinet and support platform, (You may
want to drill pilot holes prior to installing the mounting
screws.) Install one mounting screw through the hole
provided in the front. A pair of holes go through the side
of the chassis for mounting to the cabinet walls.
3. When the drawer comes loose on the slide, repeat the
same process on the opposite side.
4. Grip the drawer on both sides and pull it free.
5. For safety, push both drawer slides into the drawer
opening.
continued...
STEP 2: Push
locking tab
STEP 3: Pull up on
front of drawer
Drawer Slide
7
Download from Www.Somanuals.com. All Manuals Search And Download.
In s t a l l a t Io n In s t r u c t Io n s
re-In s t a l l In g t h e Dr a W e r
In s t a l l a t Io n ch e c k l Is t
1. Pull the drawer slides all the way out of the drawer
opening.
WARNING
To ensure a safe and proper installation, the
following checklist should be completed by the
installer to ensure that no part of the installation
has been overlooked.
2. Gently lower the drawer between the extended slides
until the drawer is suspended by the slide rails.
3. Slide the back of the drawer mounting brackets under
the drawer mounting clips on the slides.
Proper installation is the responsibility of the
homeowner. The importance of proper installation
of your warming oven cannot be over-emphasized.
4. Push the side of the drawer down onto its locking tab,
until the tab locks into place.
5. Repeat the same process on the opposite side.
6. Gently open and close the drawer to make sure that it
is properly installed.
□
Has a properly grounded, dedicated, three prong
electrical outlet been installed for the appliance by a
licensed electrician? See page 6.
STEP 3: Slide mounting
bracket under clip on
slide
STEP 4: Push front of
drawer down until tabs
lock into place
□
□
Has the mounting platform been installed according to
the instructions on page 6?
Has the chassis been properly fastened to the
mounting platform and sides of the cabinet?
See page 7.
Clip on slide
□
□
□
Has the drawer been properly installed?
Has proper operation been verified?
Have any problems been noted on the warranty card
or during the on-line warranty activation? Has the
warranty been activated on-line or the warranty card
filled out completely and mailed?
Slide
verIfyIng op e r a t Io n
1. Before connecting the power plug, turn the
TEMPERATURE and TIMER knobs are set to the OFF
position.
2. Plug the power cord into the electrical outlet.
3. Operate the warming drawer as outlined in the use and
care manual that accompanied this product.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Download from Www.Somanuals.com. All Manuals Search And Download.
|