Installation Instructions
Distinctive Series Coop
Model DCT365
Part No. 106927 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
Important Information About
Safety Instructions
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN
THE EVENT OF A RANGE TOP GREASE FIRE:
•
•
The Important Safety Instructions and warnings in
these instructions are not meant to cover all possible
problems and conditions that can occur. Use common
sense and caution when installing, maintaining or oper-
ating this or any other appliance.
a. SMOTHER FLAMES with a close-fitting lid, cookie
sheet or metal tray, then turn off the burner. BE
CAREFUL TO PREVENT BURNS. If the flames do
not go out immediately, EVACUATE AND CALL THE
FIRE DEPARTMENT.
Always contact the Dacor Customer Service Team
about problems and conditions that you don’t under-
stand. See Customer Service Information.
b. NEVER PICK UP A FLAMING PAN - you may be
burned.
c. DO NOT USE WATER, including wet dish cloths or
towels - a violent steam explosion may result.
Safety Symbols and Labels
d. Use a fire extinguisher ONLY if:
◊
You havlass ABC extinguisher, and you
alreadow to operate it.
DANGER
Immediate hazards that WILL result in severe personal
injury or death.
◊
Thd contained in the area where
nt is being called.
WARNING
Hazards or unsafe practices that COULD result in severe
he fire with your back to an exit.
personal injury or death.
WARNING
– NEVER use this appliance as a space
heat or warm the room. Doing so may result
on monoxide poisoning and overheating of the
liance.
CAUTION
Hazards or unsafe practices that COULD resul
personal injury or property damage.
WARNING
DANGE
WARNING – NEVER cover any slots, holes or passages
on the cooktop and cooktop chassis. Doing so blocks
air flow through the cooktop and may cause carbon
monoxide poisoning. Aluminum foil linings may also trap
heat, causing a fire hazard. Keep all slots, holes and
passages clear of grease and grime.
IMPORTANT: If you smell gas:
•
•
Do not use or light any
Do not touch any elecny electri-
cal devices, including thyour building.
•
•
From a neighbor’s phone, imely call the gas
supplier. Follow the gas supplis instructions.
CALIFORNIA PROPOSITION 65 WARNING
If you cannot contact the gas supplier, call the fire
department.
The burning of gas cooking fuel generates some
by-products that are on the list of substances which
are known by the State of California to cause cancer or
reproductive harm. California law requires businesses
to warn customers of potential exposure to such
substances. To minimize exposure to these substances,
always operate this unit according to the use and care
manual, ensuring you provide good ventilation when
cooking with gas.
DANGER
IMPORTANT: Do not store or use combustible, flammable
or explosive vapors and liquids (such as gasoline) on or
in the vicinity of this or any other appliance. Also keep
items that could explode, such as aerosol cans, away
from the cooktop. Do not store flammable or explosive
materials in adjacent cabinets or areas (including above
and below the cooktop).
READ AND SAVE THESE INSTRUCTIONS
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
General Safety Precautions
To reduce the risk of fire, electric shock, serious injury or death when using this appliance, follow basic safety precautions,
including the following:
WARNING
WARNING
•
•
•
Read the accompanying use and care manual com-
pletely before operating this appliance.
•
Do not leave children alone or unattended in the
area around the cooktop. Do not allow children to
play with the controls or touch other parts of the
cooktop. Do not store items of interest to children
on top of or above the cooktop. Children could be
burned or injured while climbing on the appliance.
Keep packaging materials away from children.
Plastic sheets and bags can cause suffocation.
If you receive a damaged product, immediately con-
tact your dealer or builder. Do not install or use a
damaged appliance.
•
•
Clean the cooktop thoroughly before operating it for
the first time. Make sure that all the cooktop parts
are dry before lighting a burner.
•
This cooktop must be properly installed and ground-
ed by a qualified installer according to these instal-
lation instructions prior to use. The installer should
show the customer the location of the gas shut off
valve and the power cord so that they know where
and how to turn off the gas supply and disconnect
power to the cooktop.
Keep flammas, such as paper, cardboard,
plastic and om the burners and other
hot surfsuch items on the
cooktolders to touch hot sur-
fac
•
hanging apparel while using
ot allow clothing to come into con-
oktop and surrounding areas during
tely after use.
•
•
•
Do not use this appliance in combination with a sur-
face (countertop) ventilation system. Dacor strongly
recommends the installation of a range hood in con-
junction with this appliance.
e towels or bulky cloth as pot holders.
Do not install, repair or replace any part of the
cooktop unless specifically recommended in th
ature accompanying it. A qualified service te
should perform all other service.
t use the cooktop to heat sealed containers.
e container and contents may explode, causing
personal injury.
Before servicing or installing this coo
that the gas supply is turned off at
valve and that the power plug is
the electrical outlet.
•
If the cooktop is near a window, do not use long cur-
tains as window treatment. The curtains could blow
over the cooktop and create a fire hazard.
Non-stick coatings, when heated, can be harmful to
birds. Remove birds to a separate, well-ventilated
room when operating the cooktop.
•
•
Disconnect the power pluutlet
before cleaning. Clean ththe
manner specified in the use ual.
IMPORTANT - This appliance
is equipped with a three-
prong grounding plug for your
protection against possible
electric shock hazards. Plug it
only into a dedicated, grounded
three-prong electrical outlet.
Only use the cooktop for cookins expected of
a home appliance as outlined in thliterature accom-
panying it. This cooktop is not intended for commer-
cial or laboratory use.
•
DO NOT TOUCH THE SURFACES OF THE
COOKTOP DURING OR IMMEDIATELY AFTER
USE.
It is the responsibility of the
customer to make sure the proper type of outlet is
installed. Do not under any circumstances:
•
•
•
•
Do not operate this appliance if the power cord is
damaged.
•
Cut or remove the third (ground) prong from the
power cord.
Turn the knobs to the OFF position prior to removing
them from the valve stems.
•
•
•
•
Use an adapter plug.
To avoid a fire hazard, do not hang flammable or
heat sensitive objects over the cooktop.
Use an extension cord.
Do not climb on any part of the appliance.
Use a power cord that is frayed or damaged.
Connect to an electrical outlet with a ground fault
interrupter (GFI).
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Specifications
WARNING
Observe all governing codes and ordinances during planning and installation. Contact your local building department for
further information.
Product Dimensions
All tolerances ±1/16” (±1.6 mm) unless otherwise noted.
36"
(91.4 cm)
2" (5.1 cm)
countertop
to cooking surface
4" (10.2 cm)
chassis height
21"
(53.3 cm)
Rear
overhang
3
Fro
ov
11
"
"
1 /16
1 /32
(3.0 cm)
m)
(3.4 cm)
5
9
"
33 /16 (84.6 cm)
19 /32" (49.0 cm
Side Vi
Front View
roduct Dimensions
Front of cooktop
Power
cord in
½” male NPT
gas inlet*
Front of unit
1 ¾"
(4.4 cm)
Chassis
2"
½” male
1 ¾"
NPT gas inlet
(4.4 cm)
(5.1 cm)
Power cord
42” (106.7 cm) long
Top panel overhang
*Gas inlet protudes ½” (1.3 cm) from bottom
Utility Locations
Utility Dimensions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Specifications
Electrical Requirements
Gas Supply Requirements
•
Be certain that the cooktop being installed is correct for
the gas service being provided (natural gas or LP gas).
Also, if operating the cooktop at an altitude above 4000
ft. (1219 m) make sure it is equipped for high altitude
operation.
WARNING
To prevent an electric shock hazard, the power supply
must meet the specifications stated below. It is the own-
er’s responsibility to make sure that the electrical service
meets electrical requirements and that the electrical outlet
has been properly installed by a licensed electrician.
•
•
•
Units equipped for LP operation have “LP” in the
model number listed on the product data label. See the
Chassis Bottom Diagram for label location.
•
•
The cooktop is supplied with a factory installed, 42-inch
long, power cord with a three-prong, grounding elec-
trical plug. It is connected to the chassis at the bot-
tom right rear corner (see Chassis Bottom Diagram
below). It must be connected to a dedicated, grounded
three-prong electrical outlet installed by a licensed elec-
trician.
Units equipped for high altitude operation have an “H”
at the end of the model number listed on the product
data label.
Check your local building codes for the proper method
of installation. In the absence of local codes, this
appliance shoulnstalled in accordance with the
National Fuel ANSI Z223.1/NFPA 54.
The electrical installation, including minimum supply
wire size and grounding, must be done in accordance
with National Electric Code ANSI/NFPA 70 and local
codes and ordinances. A copy of this standard may be
obtained from:
•
•
An externvalve must be installed
betweee cooktop for the purpose
of tuff gas to the appliance.
om the factory with a regulator in
Use only the regulator provided.
st be installed in the gas line that runs
op gas inlet to the gas shut off valve.
National Fire Protection Association
1 Batterymarch Park
Quincy, MA 02269-9101
•
•
The correct voltage, frequency and amperage must
supplied to the electrical outlet according to the p
data label located on the bottom of the chassis
the Gas and Electrical Requirements table
page for reference.
tor inlet (female) accommodates a 3/4” gas
an also accommodate a 1/2” gas line using
cluded reducer. The inlet to the cooktop itself is
uipped with a ½” male NPT fitting.
e cooktop gas connection is located on the bottom of the
cooktop in the back right corner as you face the front of the
unit. See the Chassis Bottom Diagram on this page.
Be certain to locate the electrical outl
power cord may be easily disconne
requires service.
DCT365S/NG
DCT365S/LP
Front of unit
Gas type
Natural gas
LP gas
Manifold
pressure
5” Water
column
10” Water
column
Min. gas supply
pressure *
6” Water
column
11” Water
column
Product data label
Max. gas supply
pressure
1/2 p.s.i.
1/2 p.s.i.
Total connected
load
0.25 Amp.
(30 Watts)
0.25 Amp.
(30 Watts)
Circuit
120 Vac,
120 Vac,
requirement
60 Hz, 15 Amp.
60 Hz, 15 Amp.
Chassis Bottom Diagram
Gas and Electrical Requirements**
* The gas supply pressure for testing the regulator setting
shall be at least 1 inch water column (249 Pa) above the
specified manifold pressure.
** The electrical and gas data on this page is for reference
only. If the above data does not agree with the product data
label, use the data on the product data label.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Specifications
•
Allow a minimum ¼” (6 mm) clearance between the
Cabinet and Countertop Layout
bottom of the cooktop chassis and all combustible sur-
faces, including the upper edge of a drawer installed
below the cooktop.
WARNING
•
•
Failure to meet or exceed the maximum and mini-
mum dimensions/clearances stated in these instruc-
tions may result in a fire hazard.
Follow the countertop manufacturer’s instructions
regarding the minimum corner radius, use of heat
reflective tape, reinforcement of corners, etc.
¼” (6 mm)
mimimum clearance
to combustible
surfaces
35 ¼” (89.5 cm)*
•
•
Carefully check the location where the cooktop will be
installed. For best performance, the cooktop should be
placed away from drafts that may be caused by doors,
windows and heating and air conditioning outlets.
* Allows for clearance between hold down brackets
Under Cabinet Clearances
This appliance is to be used in conjunction with a suit-
able vent hood.
•
The gas suping, gas shut-off valve and the elec-
trical outleocated so that they do not inter-
fere witen it is installed. If installing
anotabinet below, allow for the
roical service behind it.
All tolerances +1/16” (+1.6 mm), -0
unless otherwise noted.
A
Thllow for the following:
Combustible overhead
cabinets
s shut-off valve and regulator when
alled.
the electrical outlet when the cooktop is in
he 42” (106.7 cm) power cord must be able to
the electrical outlet.
13" max.3
(33.0 cm)
18"
(
•
ccess to the underside of the cooktop for service and
inspection purposes.
Clearance inside the cabinet to allow for proper hold
down bracket installation.
30" min.1, 2
(76.2 cm)
Combustible
surface to rear
To allow access to the utilities and cooktop bottom, a fixed
shelf should not be installed below the cooktop. See the fol-
lowing pages for countertop cutout dimensions.
See cutout
dimensions
utout dimensions
1 Measured from the cooking surface (top of cooktop grate).
2 If installing with an overhead vent hood, also check the hood
specifications for minimum required clearances.
3 Not applicable for cabinets more than a horizontal distance of
5 ½” (14.0 cm) from edge of cooktop. Allow 6 7/8” (17.5 cm)
from cutout edge.
Minimum Required Clearances Around the Cooktop
(A) Minimum
(A) Recommended
36” (91.4 cm)
42” (106.7 cm)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Specifications
Cutout Dimensions
All tolerances +1/16” -0 (+1.6 mm, 0) unless otherwise noted.
Rear
wall
Vertical
combustible
surface
4 ¼
F
f
C
E
D
F
(
Minimum distance to combustible side
wall above countertop (both sides)
(C) Minimum
3 ¼” (8.3 cm)
(D)
19 / ” (49.9 cm)
(E)
33 / ” (85.4 cm)
(F) Minimum
5
5
7
6 / ” (17.5 cm)
8
8
8
Countertop Cutout Dimensions
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Verify Package Contents
Connecting the Gas Line
•
•
•
•
•
Hold down brackets (2)
WARNING
Verify that the gas supply meets specifications before
connection. See page 4.
Grates (3)
•
•
Burner sets (5)
Gas pressure regulator with ¾” to ½” reducer
Stainless steel cleaner
Do not install the cooktop without also installing the
included gas regulator. Do not use the cooktop with-
out the regulator installed.
Installing the Cooktop
•
•
•
•
•
Ensure that the arrow on the regulator points in the
direction of the gas flow, towards the cooktop.
WARNING
Verify that the power supply meets the specifications
on page 4 before proceeding.
Do not apply excessive pressure when tightening gas
connections and fittings.
•
•
Do not use Teflon tape or plumber’s putty on flexible
gas line conons.
To prevent damage to the gas pressure regulator,
install it only after the cooktop is mounted in its per-
manent position.
Test the r leaks as instructed before use.
Do noheck for leaks.
Thy pressure to the regulator
pounds per square inch (p.s.i.)
CAUTION
Do not over-tighten the hold down bolts. Over tight-
ening the hold down bolts may result in improper
operation of the dual gas burners.
•
•
d shut-off valve must be disconnected
supply piping system during any pres-
g exceeding ½ p.s.i. (3.5 kPa).
Do not use a hardening compound or caulk to per
nently seal the cooktop into place. The cooktop
be readily removable if service is required. R
of sealant to service the unit will be perfor
customer’s expense.
ooktop must be isolated from the gas supply
ng system by closing the shut-off valve to the
ooktop during any gas supply piping system pres-
sure testing equal to or less than ½ p.s.i. (3.5 kPa).
1. Lower the cooktop into the cutout. S
far as possible and center it side
•
For LP gas installations, the LP gas tank must have
its own high-pressure regulator in addition to the
pressure regulator supplied with the cooktop.
2. Secure the cooktop to the cou(2)
provided hold-down bracke
1. Attach the gas pressure regulator (included with the
cooktop) to the cooktop pipe nipple inlet. For tight
installations, the regulator may be installed upstream
from the pipe nipple, anywhere between the shut-off
valve and the cooktop. For best performance, minimize
gas pressure loss by attaching the regulator as close
as possible to the cooktop gas inlet.
Hold down
bracket mounting holes
2. Complete connection of the gas supply to the cooktop
by installing a minimum ½” flexible gas line (not includ-
ed) between the pressure regulator and the shut-off
valve.
(both sides)
Gas inlet
Power cord
3. Check for gas leaks:
◊
◊
Turn all cooktop control valves to the OFF position.
Turn on the gas supply valve and check all lines
and connections for leaks using a soap and water
solution or a gas leak detector.
◊
Turn the gas supply off.
Hold Down Bracket Installation
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Installing the Burner Components
Left grate,
curved fingers
on left
WARNING
Never attempt to operate the cooktop with any of the
burner parts removed.
Slot on
bottom
•
•
Center grate
Slot on
bottom
Do not attempt to adjust the burner air mixture set-
tings. All adjustments are preset at the factory.
Slot on
bottom
1. Remove the burner rings, burner caps and grates from
their shipping packages.
2. Assemble the burners as shown. Match the burner
parts to the correct size and type of burner. When
installing the burner components, make sure they are
centered. Twist each piece back and forth slightly until
it drops completely into place. The burners will not
operate properly unless all of the burner pieces are
properly seated.
Right grate,
curved fingers
on right
3. Gently set the grates on top of the spill tray. Make sure
that the rubber feet are positioned in the dimples.
Notch
IMPORTANT
Each grate is different. Orient them as shown. Each grate
has a slot on the bottom that matches up with a notch on
the spill try. The slots on the grates all go toward the ba
of the cooktop.
ear™
rner
Standard
burner
Inner burner cap
(bottom shown)
Burner cap
(bottom shown)
Fit hole in burner
ring over igniter
Outer burner cap
Burner ring
Burner ring
Line up
indentations on
bottom of burner
ring with pins on
top of base.
Igniter
CAUTION: Top of
igniter is sharp
Burner base
Burner base
SimmerSear™ Burner Assembly
Standard Burner Assembly
(2 large, 2 small)
(center of cooktop)
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
NOTE: If the cooktop does not operate properly, follow
these troubleshooting steps:
Verifying Proper Operation
•
•
Verify that power and gas are supplied to the cooktop.
WARNING
Check to make sure that the power plug is connected
to the electrical outlet and that power is turned on at
the circuit breaker panel or fuse box.
•
Make sure that power to the electrical outlet is turned
off at the circuit breaker panel or fuse box and that
the gas is turned off at the gas supply valve before
proceeding.
•
•
Check to make sure that the burner parts are properly
seated.
•
The cooktop must be properly grounded at all times
when electrical power is applied.
If the burner continues to spark after ignition without
stopping, have a licensed electrician check the electri-
cal outlet for proper grounding or reversed polarity.
Prior to operating the cooktop, read the accompanying use
and care manual carefully.
•
•
Repeat the above burner ignition test.
1. Make sure all the cooktop burner controls are in the
If the appliance still does not work, contact Dacor
Distinctive Service at (877) 337-3226. Do not attempt
to repair the aance yourself. If you need service, be
sure to havel and serial numbers available
when yode cover for location.
OFF position.
2. Connect the power cord to the electrical outlet.
3. Turn on power to the electrical outlet at the circuit
breaker panel or fuse box.
Dacor is e cost of correcting problems
causen.
4. Push down and turn the left front burner control knob
slowly counterclockwise to the HIGH posi-
tion. The corresponding burner indicator light
should come on. Verify that the burner igniter
sparks, then return the knob to the OFF
HIG
po
position. Repeat for all of the remaining
control knobs.
5. Turn on the gas supply valve.
HIGH
position
6. Perform the following ignition test for all of
one at a time:
LOW
position
•
Push down and turn the control
terclockwise to the HIGH pos
igniters will spark. It may tor
the burner to ignite, at will
stop sparking. If ignithin 4
seconds, turn the n. Wait for
at least 5 minutes to dissipate,
then repeat the test.
SimmerSear Control Knob (Center)
•
•
Once the burner lights, rotahe control knob
counterclockwise from HIGH to LOW to adjust the
flame height progressively. On the SimmerSear
burner, only the center of the burner should be lit
when the knob is in the low position.
When the unit is installed properly, the flame will
be steady. It will
also have a sharp,
blue inner cone
HIGH
position
that will vary in
length proportional
to the burner size.
The flame will be
reduced by the
LOW
Smart Flame™
position
feature under the
grate fingers to
Standard Burner Control Knob
increase grate life.
Normal Flame Appearance
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Installation Checklist
WARNING
To ensure a safe and proper installation, the follow-
•
ing checklist should be completed by the installer to
ensure that no part of the installation has been over-
looked.
•
Proper installation is the responsibility of the home-
owner. The importance of proper installation of your
Dacor cooktop cannot be overemphasized.
□
Is the electrical outlet for the cooktop grounded and
located according to these instructions and in accor-
dance with all applicable electrical codes? See page
4.
□
□
Is the gas service for the cooktop located and installed
according to these instructions and in accordance with
all applicable codes? See page 4.
Has the gas supply inlet pressure been measured to
ensure that it does not exceed the maximums stated in
these instructions? See page 4.
□
□
Is the cooktop secured using the provided hold-down
brackets? See page 7.
Is the cooktop connected to the gas supply acc
to these instructions and in accordance with
cable codes? Did the installer check the g
leaks? See page 7.
□
Are the burners and grates properl
to these instructions? See page
□
□
Has proper operation been
Has the warranty been actie warranty
card filled out completely and
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Wiring Diagram
WARNING
Label all wires prior to dis-connection when servicing
controls. Wiring errors can cause improper and
dangerous operation.
Verify proper operation
after servicing
120 Vac, 60 Hz.
power supply
Wiring Diagram - DCT365
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|