XR10/XR20 Command Processor Panels
Installation Guide
10/26 Zone Burglary/Fire/Access Control Panels with Built-in Communicator
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
LT-0229 (5/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Section
Panel Specifications
Power supply........................................................................................ 1.1
Communication .................................................................................... 1.2
Panel zones ......................................................................................... 1.3
Keypads ............................................................................................... 1.4
Outputs................................................................................................. 1.5
Enclosure specifications....................................................................... 1.6
Introduction
Description ........................................................................................... 2.1
System configurations .......................................................................... 2.2
Before you begin .................................................................................. 2.3
About this guide ................................................................................... 2.4
How to use this guide ........................................................................... 2.5
System Components
Description ........................................................................................... 3.1
Wiring diagram ..................................................................................... 3.2
Lightning protection .............................................................................. 3.3
Security Command keypads ................................................................ 3.4
Installation
Mounting the enclosure ........................................................................ 4.1
Mounting keypads ................................................................................ 4.2
Wiring Keypads .................................................................................... 4.3
Primary Power Supply
AC terminals 1 and 2............................................................................ 5.1
Transformer types ................................................................................ 5.2
Secondary Power Supply
Battery terminals 3 and 4 ..................................................................... 6.1
Earth ground ........................................................................................ 6.2
Replacement period ............................................................................. 6.3
Discharge/recharge .............................................................................. 6.4
Battery supervision............................................................................... 6.5
XR10/XR20 power requirements ......................................................... 6.6
Bell Output
Terminals 5 and 6 ................................................................................ 7.1
Keypad Data Bus
Description ........................................................................................... 8.1
Terminal 7 - RED ............................................................................... 8.2
Terminal 8 - YELLOW ........................................................................ 8.3
Terminal 9 - GREEN .......................................................................... 8.4
Terminal 10 - BLACK ........................................................................... 8.5
Smoke and Glassbreak Detector Output
Terminal 11 .......................................................................................... 9.1
Burglary Zones
Description ......................................................................................... 10.1
Operational parameters ..................................................................... 10.2
Zone response time ........................................................................... 10.3
Keyswitch arming zone ...................................................................... 10.4
Powered Zone for 2-Wire Smoke Detectors
Terminals 25 and 26 .......................................................................... 11.1
Annunciator Outputs
Description ......................................................................................... 12.1
Harness wiring ................................................................................... 12.2
Telephone RJ Connector
Description ......................................................................................... 13.1
FCC registration ................................................................................. 13.2
Notification ......................................................................................... 13.3
Ground start ....................................................................................... 13.4
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Section
Reset Jumpers J16
Description ......................................................................................... 14.1
Universal UL Burglary Specifications
Introduction ........................................................................................ 15.1
Wiring ................................................................................................. 15.2
Police station phone numbers ............................................................ 15.3
Bypass reports ................................................................................... 15.4
System maintenance.......................................................................... 15.5
Cross Zoning ...................................................................................... 15.6
Ground Start....................................................................................... 15.7
UL 1023 Specifications
Bell cutoff ........................................................................................... 16.1
Entry delay ......................................................................................... 16.2
Exit delay............................................................................................ 16.3
Zone expansion on 4-wire bus ........................................................... 16.4
UL 1610 and 1076 Specifications
Opening/Closing reports .................................................................... 17.1
Automatic bell test .............................................................................. 17.2
Proprietary dialer ................................................................................ 17.3
UL 1635 Specifications
Digital dialer telephone number ......................................................... 18.1
Entry delay ......................................................................................... 18.2
Exit delay............................................................................................ 18.3
Test frequency ................................................................................... 18.4
Automatic bell test .............................................................................. 18.5
Grade B Central Station ..................................................................... 18.6
UL 365 and 609 Specifications
Entry delay ......................................................................................... 19.1
Grade A bell ....................................................................................... 19.2
Bell cutoff ........................................................................................... 19.3
Automatic bell test .............................................................................. 19.4
Grade A Mercantile ............................................................................ 19.5
Mercantile Safe and Vault .................................................................. 19.6
Line security for Police Connect......................................................... 19.7
Universal UL and NFPA Fire Alarm Specifications
Introduction ........................................................................................ 20.1
Wiring ................................................................................................. 20.2
Police station phone number.............................................................. 20.3
System maintenance.......................................................................... 20.4
Audible alarm ..................................................................................... 20.5
Fire zone programming ...................................................................... 20.6
Ground Start....................................................................................... 20.7
UL 985 NFPA 72 (chapter 2) Specifications
Bell output definition ........................................................................... 21.1
California State Fire Marshal Specifications
Bell output definition ........................................................................... 22.1
Troubleshooting Section
Description ......................................................................................... 23.1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Panel Specifications
1.1 Power supply
Transformer Input: 16.5 VAC 40VA (Models 320 wire-in or 321 plug-in)
Standby Battery: 12 VDC 6.5Ah (40VA transformer charges up to 2 batteries)
Auxiliary Output: 12 VDC at 500mA
Bell Output: 12 VDC at 1.5 Amps
Smoke Detector Output: 12 VDC at 100mA
All circuits inherent power limited
1.2 Communication
Built-in SDLC Digital Dialer communication to DMP Model SCS-1 Receivers
Built-in 4-2 communication to non-DMP receivers.
Built-in M2E (Radionics Modem IIe) communication to non-DMP receivers (XR20 only).
Either panel can operate as a local system
1.3 Panel zones
Nine 1k Ω EOL burglary zones (zones 1 to 9)
One 3.3k Ω EOL Class B powered fire zone with reset capability (zone 10)
1.4 Keypads
You can connect up to four of the following supervised keypads to the XR10/XR20 panels.
• 16 or 32 character alphanumeric keypads
• 10-zone LED keypads
In addition, the following zone expanders can be added to the XR20 panel:
• Four and single point zone expanders
• Single point PIR and glassbreak detectors
When using the FA426 Wireless Receiver, the XR20 allows unsupervised devices to be added to address five.
1.5 Outputs
The XR10/XR20 panels provide four open collector outputs rated for 50mA each. See section 12.1. A Model 300
Wire Harness is required. Open collectors don't provide voltage but instead ground a positive voltage source.
1.6 Enclosure specifications
The XR10/XR20 ship in an enclosure with EOL resistors, battery leads, user's guide, and programming sheet.
Size:
12.5" W x 9.5" H x 2.75" D
4 lbs
Weight:
Color:
Gray or Black
Construction:
20 gauge cold rolled steel
Introduction
2.1 Description
The DMP XR10/XR20 Command Processors are powerful 12 VDC burglary and fire communicator panels with
battery backup. The XR10/XR20 provide nine on-board burglary zones and one on-board 12 VDC Class B
powered fire zone. The fire zone has a reset capability to provide for 2-wire smoke detectors, relays, or other
latching devices. The XR10/XR20 can communicate to one or two DMP SCS-1 Receivers using SDLC digital
dialer or 4-2 reporting formats. In addition, the XR20 can communicate using the Radionics Modem IIe format.
2.2 System configurations
The XR10/XR20 can be programmed to operate as either an All/Perimeter system that provides one Perimeter
area and one Interior area, or as a Home/Sleep/Away system that provides one Perimeter, one Interior, and one
Bedrooms area. The Bedrooms area can include any protection devices the user wants disarmed during their
sleeping hours and armed in the Away mode. In addition, the XR20 can operate as a four area system.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
2.3 Before you begin
Before installing the XR10/XR20, we recommend you read through the entire contents of this guide. Familiarize
yourself with the features of the panel and the key points to remember during the installation. Be sure to read
and understand all of the caution statements printed in bold italics.
In addition to this installation guide, you should also read through and familiarize yourself with these other
product documents:
• XR10 Programming Guide (LT-0230)
• XR20 Programming Guide (LT-0305)
• XR10 Security Command User's Guide (LT-0226)
• XR20 Security Command User's Guide (LT-0303)
• XR10 Program Information Sheet (LT-0212)
• XR20 Program Information Sheet (LT-0302)
2.4 About this guide
The information contained in this guide is organized into three sections: Table of Contents, Introduction, and
Installation.
• The Table of Contents at the front of this guide lists all of the headings and subheadings used throughout
each section. To the right of each heading is the section number where the information can be found.
• The Introduction section gives you an overview of the various components that go into a XR10/XR20
system and diagrams some typical system configurations. This section gives descriptions of the panel,
keypads, and accessory modules and provides details on how each of them operate together in the
system.
• The Installation section begins with mounting instructions for the enclosure and takes you through the
proper way to power up the panel prior to programming.
Caution notes
Throughout this guide you'll see caution notes containing information you need to know when installing the
XR10/XR20 panel. These cautions are written with a bold, italicized introductory clause followed by a detailed
description of the caution. See the example shown below:
Always ground the panel before applying power to any devices: The XR10/XR20 must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components.
Whenever you see a caution note, make sure you completely read and understand its information. Failing to
follow the caution note can cause damage to the equipment or improper operation of one or more components in
the system.
2.5 How to use this guide
To locate information about the installation of the XR10/XR20, first go to the Table of Contents at the front of this
guide. Find the subject heading that closely describes the information you need and turn to the section number
shown to the right of the heading.
The text that follows the heading has been written to provide as much information about the subject as possible.
If you can't find the information you need under that heading, try scanning through a few of the headings before
and after and reading the text under those that sound similar.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
System Components
3.1 Description
The DMP XR10/XR20 system is made up of an alarm panel with built in communicator, an enclosure, a 16.5 VAC
transformer, and a 12 VDC 6.5 Ah battery. You can add up to four Security Command keypads to the system and
can also connect auxiliary devices to the panel's open collector outputs to expand the basic system. Combined
current requirements of additional modules may require an auxiliary power supply. Refer to section 6.6 in this guide
when calculating power requirements. In addition, up to 16 points of zone expansion can be added to the XR20.
3.2 Wiring diagram
The XR10/XR20 system below shows some of the accessory devices you can connect for use in various
applications. A complete description of each module follows. Zone expanders can be added to the XR20.
J11
J16
Output Header J11
1
2
3
4
All outputs must be connected
to devices located within the
same room as the control panel.
Command Processor Reset
Use DMP Model 300 Harness.
AC wiring must be in
conduit and exit out the left
side of the panel enclosure.
J4
Wiring on terminals 5 through 17 must exit
to the right and maintain a 1/4" separation
from the AC and battery positive wiring.
Front Tamper
Phone Jack Connector
U11
DMP transformers:
Model 320
Plug into
120 VAC
outlet not
controlled
by switch.
16.5 VAC 40VA
wire-in
Rear Tamper
Model 321
16.5 VAC 40VA
plug-in
Tamper protection
when required for
Model 349A Attack
Resistant Enclosure.
1
2
3
4
5
6
7
8
9
10
11
12
15
16
17
18
19
20
22
23
24
25
26
13
14
21
AC
AC
+B
-B BELL GND RED YEL GRN BLK
Z1 GND
Z3
GND
Z10+ Z10-
SMK
Z2
GND
Z4
Z5
Z6
Z 7 GND Z 8 Z 9
Secondary Power Supply
1.2 Amps max. charging current.
Use only 12 VDC rechargable
batteries. DMP Model 367.
Replace every 3 to 5 years.
16 to 18 gauge wire
Zone 10 compatibility
identifier: A
MaximumACwiredistance
With16gaugewire:70feet
With18guagewire:40feet
Maximumoperating
range:
8.8VDCto14.2VDC.
2-wire
smoke
detector
1k Ω
1k Ω
1k Ω 1k Ω
1k Ω 1k Ω
1k Ω 1k Ω
Cold Water Pipe
Earth Ground
Smoke Output
1k Ω
100mA at 10.4 to 13.2 VDC
Terminal 11
Seesection11.1intheXR20
InstallationGuide(LT-0229)foralist
ofapproved2-wiresmokedetectors.
Bell
10.4 to 13.2 VDC
Red
Total current 1.5 Amps max.
Black
Bell
4-wire smoke detector
Heatdetectors, manualpullstations,
oranyothershortingdevice.
Unlimitednumberofunits.
Household System
An alarm sounding device
must be installed indoors
so that it is clearly heard
in all sleeping areas.
Smoke
Power
Detector
Supervision
Relay
Up to 500mA auxiliary
current at 10.4 to 13.2 VDC
from Terminal 7.
+ –
Keypads
Models 670, 770, and
771
3.3k Ω
DMP Model 309
100mA at 8 to 16 VDC
125mA with display lit.
Model 692
75mA at 8 to 16 VDC.
Up to four keypads can
be connected to the
XR10/XR20.
ZONE EXPANDER
Model 714
15mA at 12 VDC
ZONE EXPANDER
Model 715
15mA at 12 VDC
XR20 only
Figure 1: XR10/XR20 wiring diagram
3.3 Lightning protection
Metal Oxide Varistors and Transient Voltage Suppressors help protect against voltage surges on input and
output circuits of the XR10. Additional surge protection is available by installing the DMP 370 or 370RJ Lightning
Suppressors.
3.4 Security Command® keypads
You can connect any combination of up to four Model 670, 770, and 771 vacuum fluorescent, 690, 693, 790,
791, and 793 LCD, or 692 LED Security Command Keypads to the 4-wire keypad data bus provided by the
panel on terminals 7, 8, 9, and 10. (Note: The XR10 does not support zone expansion on the keypad bus.)
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation
4.1 Mounting the enclosure
The metal enclosure for the XR10/XR20 must be mounted in a secure, dry place to protect the panel from
damage due to tampering or the elements. It is not necessary to remove the XR10/XR20 PC board when
installing the enclosure.
Dual 1/2" and 3/4" Conduit Knockouts
J11
J16
1
2
3
4
Reset Jumper
J4
Phone Jack Connector
U11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Z
24
25
26
AC
AC
+B
-B BELL GND RED YEL GRN BLK SMK
Z1 GND
Z2
Z3 GND
Z4
Z5 GND Z6
Z
7
GND
8
Z10+ Z10-
Z
9
Enclosure Mounting Holes
Dual 1/2" and 3/4" Conduit Knockouts
Figure 2: XR10/XR20 in standard enclosure
Accessory Module
Mounting Holes
Accessory Module
Mounting Holes
Dual 1/2" and 3/4" Conduit Knockouts
Tamper Switch
Mounting Holes
Enclosure Mounting Holes
J11
J16
1
2
3
4
Reset Jumper
J4
Phone Jack Connector
U11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Z
24
25
26
AC
AC
+B
-B BELL GND RED YEL GRN BLK SMK
Z1 GND
Z2
Z3 GND
Z4
Z5 GND Z6
Z
7
GND
8
Z
9
Z10+ Z10-
Wire Access
Openings
Enclosure Mounting Holes
Battery Shelf
Dual 1/2" and 3/4" Conduit Knockouts
Figure 2A: XR10/XR20 in optional 349 Enclosure
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
4.2 Mounting keypads
Security Command keypads have removable covers that allow you to easily mount the base with keypad circuit
board to a wall or other flat surface using the screw holes provided on each corner. Before mounting the base,
connect the keypad wire harness leads to the 4-wire keypad data bus cable from the panel. Next, attach the
keypad wire harness connector to the pin connector on the keypad circuit board, mount the base, and install the
keypad cover making sure all of the keys extend through their respective holes.
For mounting keypads on solid walls, or for applications where conduit is required, use a DMP 775, 776, or 778
keypad conduit backbox.
4.3 Wiring keypads
Keypad data bus
The keypad data bus consists of a 4-wire cable that provides 12 VDC power, data in, data out, and a panel
common. You can connect keypads in parallel on one 4-wire cable or provide a separate cable run back to the
panel for each keypad. The maximum cable length for one keypad can be up to 500 feet using 22 gauge wire or
up to 1000 feet using 18 gauge wire. Additional keypads installed on the same cable decrease the maximum
distance at which they'll operate properly.
Refer to the wiring diagram in this guide for additional wiring information. See section 3.2.
Primary Power Supply
5.1 AC terminals 1 and 2
Connect the transformer wires to terminals 1 and 2 on the panel. Use no more than 70 ft. of 16 gauge, or 40 ft. of
18 gauge, wire between the transformer and the XR10/XR20.
Always ground the panel before applying power to any devices: The XR10/XR20 must be properly
grounded before connecting any devices or applying power to the panel. Proper grounding protects against
Electrostatic Discharge (ESD) that can damage system components. See Earth ground, section 6.2.
5.2 Transformer types
The standard transformer for the XR10/XR20 is 16.5 VAC 40VA, which provides up to 500mA of auxiliary current
and 100mA of smoke detector output. You can use either the Model 320 wire-in or 321 plug-in transformer with
the XR10/XR20. The total current available is limited by the total battery standby requirements of the installation.
The transformer must be connected to a 120 VAC 60 Hz commercial power outlet that is not controlled by a wall
switch. Never share the transformer output with any other equipment.
Secondary Power Supply
6.1 Battery terminals 3 and 4
Connect the black battery lead to terminal 4 on the panel and to the negative terminal of the battery. The
negative terminal connects to the enclosure ground internally through the XR10/XR20 circuit board. Connect the
red battery lead to terminal 3 on the panel and to the positive terminal of the battery. Observe polarity when
connecting the battery. The XR10 and XR20 panels can charge up to two batteries.
Use sealed lead-acid batteries only: Use the DMP Model 367, 12 VDC 6.5Ah sealed lead-acid rechargeable
battery. Batteries supplied by DMP or manufactured by Eagle Picher or Yuasa have been tested to ensure
proper charging with DMP products.
GEL CELL BATTERIES CANNOT BE USED WITH THE XR10/XR20 PANEL.
6.2 Earth ground
Terminal 4 of the XR10/XR20 panel must be connected to earth ground using 14 gauge or larger wire to provide
proper transient suppression. DMP recommends connecting to a metal cold water pipe or ground rod only. Do
not connect to electrical conduit or a telephone company ground.
6.3 Replacement period
DMP recommends the battery be replaced every 3 to 5 years under normal use.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
6.4 Discharge/recharge
The XR10/XR20 battery charging circuit float charges at 13.9 VDC at a maximum current of 1.2 Amps using a
40VA transformer. The total current available is reduced by the combined auxiliary current draw from terminals
7, 11, and 25. The various battery voltage levels are listed below:
Battery Trouble:
Battery Restored:
Below 11.9 VDC
Above 12.6 VDC
6.5 Battery supervision
The XR10/XR20 tests the battery once every hour when AC power is present. The test lasts for five seconds. A
load is placed on the battery and if its voltage falls below 11.9 VDC a low battery is detected. If AC power has
failed, a low battery is detected any time the battery voltage falls below 11.9 VDC.
If a low battery is detected with AC power present, the test is repeated every two minutes until the battery
charges above 12.6 VDC; the battery restored voltage. If a faulty battery is replaced with a fully charged battery,
the restored battery will not be detected until the next two minute test is done.
6.6 XR10/XR20 power requirements
During AC power failure, the XR10/XR20 panel and all auxiliary devices connected to the XR10/XR20 draw their
power from the battery. All devices must be taken into consideration when calculating the battery standby
capacity. Below is a list of the power requirements of the XR10/XR20 panel. Add the additional current draw of
Security Command keypads, smoke detector output, and any other auxiliary devices used in the system for the
total current required. The total is then multiplied by the total number of standby hours required to arrive at the
total ampere/hours required.
XR10/XR20 STANDBY BATTERY POWER CALCULATIONS
Standby Current
Alarm Current
XR10/XR20 Command Processor Panel
Active Zones 1-9
50mA ______ mA
Qty _____ x 1.6mA ______ mA Qty _____ x *2mA ______ mA
4mA ______ mA 30mA ______ mA
50mA ______ mA
Active Zone 10
2-Wire Smokes
Qty _____ x
.1mA ______ mA Qty _____ x .1mA ______ mA
Bell Output
1500mA max. ______ mA
670, 770, and 771 Keypads
Annunciator (ON)
Qty _____ x 125mA ______ mA Qty _____ x 125mA ______ mA
Qty _____ x 20mA ______ mA
690, 693, 790, 791, and 793 Keypads
Annunciator (ON)
Qty _____ x 100mA ______ mA Qty _____ x 100mA ______ mA
Qty _____ x 20mA ______ mA
692 Keypads
Qty _____ x
30mA ______ mA Qty _____ x 30mA ______ mA
Qty _____ x 10mA ______ mA
Annunciator (ON)
Auxiliary Powered Devices on
Terminals 7 and 11
______ mA
______ mA
(Other than keypads)
Total Standby ___________ mA
Total Alarm ____________ mA
* Based on 10% of active zones
in alarm condition
Total Standby ____________ mA x number of standby hours needed ______ = ___________ mA/hours
Total Alarm + ___________ mA/hours
Total ___________ mA/hours
x _.001_____
= ___________ A/hours required
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Bell Output
7.1 Terminals 5 and 6
Nominal 12 VDC is supplied by terminal 5 on the panel to power alarm bells or horns. The output is rated for a
maximum output of 1.5 Amps. This output can be steady or pulsed depending upon the Bell Action specified in
Output Options. Terminal 6 is the ground reference for the bell circuit.
Keypad Data Bus
8.1 Description
Terminals 7, 8, 9, and 10 of the XR10/XR20 panel are designated as the keypad data bus. In addition to
keypads, the XR20 allows the connection of any combination of zone expanders, 5845LX Glassbreak Detectors,
6155LX PIRs, and DS775LX PIRs to the data bus up to the maximum of four devices.
8.2 Terminal 7 - RED
Nominal 12 VDC is supplied at terminal 7 to power Security Command keypads and zone expanders. This is
also where power for any auxiliary device is supplied. The ground reference for terminal 7 is terminal 10. The
maximum output is rated at 500mA. All auxiliary devices totalled together must not exceed the panel's maximum
current rating of 500mA.
8.3 Terminal 8 - YELLOW
Data receive from keypads and zone expanders.
8.4 Terminal 9 - GREEN
Data transmit to keypads and zone expanders.
8.5 Terminal 10 - BLACK
Terminal 10 is the ground reference for Security Command keypads, zone expanders, and any auxiliary devices
being powered by terminals 7 and 11.
Smoke and Glassbreak Detector Output
9.1 Terminal 11
Nominal 12 VDC at 100mA maximum (shared by terminal 25) is supplied at terminal 11 to power 4-wire smoke
detectors or other auxiliary powered devices. This output can be turned off by the user for 5 seconds using the
Sensor Reset Menu Option. Terminal 10 is the ground reference for terminal 11.
Burglary Zones
10.1 Description
Terminals 12 to 24 are the nine burglary zones. For programming purposes, the zone numbers are 1 to 9. The
zone configurations on terminals 12 to 24 are described below.
Terminal
Function
Terminal
Function
12
13
14
15
16
17
18
Zone 1 voltage sensing
Ground for zones 1 & 2
Zone 2 voltage sensing
Zone 3 voltage sensing
Ground for zones 3 & 4
Zone 4 voltage sensing
Zone 5 voltage sensing
19
20
21
22
23
24
Ground for zones 5 & 6
Zone 6 voltage sensing
Zone 7 voltage sensing
Ground for zones 7, 8, & 9
Zone 8 voltage sensing
Zone 9 voltage sensing
The voltage sensing terminal measures the voltage flowing through the 1k Ω End Of Line resistor to the zone's
ground terminal. Dry contact sensing devices can be used in series (normally-closed) or in parallel (normally-
open) with any of the burglary protection zones.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
10.2 Operational parameters
Each burglary protection zone detects three conditions: open, normal, and short.
The parameters for each are listed below:
Condition
Open
Resistance on zone
over 1300 ohms
Voltage on right terminal
over 2.0 VDC
Normal
Short
600 to 1300 ohms
under 600 ohms
1.2 to 2.0 VDC
under 1.2 VDC
1K
1K
1K
NORMALLY CLOSED CONTACTS
NORMALLY OPEN CONTACTS
COMBINATION: NORMALLY OPEN AND
NORMALLY CLOSED CONTACTS
Figure 3: Protection zone contact wiring
10.3 Zone response time
A condition must be present on a zone for 500 milliseconds before it's detected by the XR10/XR20 panel.
Ensure detection devices used on the protection zones are rated for use with this delay.
10.4 Keyswitch arming zone
Momentary keyswitches
You can use a momentary keyswitch on a zone programmed as an Arming type for use in arming and disarming
the system without a code.
How it works
When the Arming zone is placed into a shorted codition from a normal condition, the panel disarms any areas
that are armed. If all areas are disarmed, the panel arms all areas.
If the Arming zone changes from normal to open while any area is armed, an alarm is indicated. If all areas are
disarmed, only a trouble is indicated.
Powered Zone for 2-Wire Smoke Detectors
11.1 Terminals 25 and 26
A resettable 2-wire Class B powered zone is provided on terminals 25 (positive) and 26 (negative) of the panel.
For programming purposes, the zone number is 10. The zone uses a Model 309, 3.3k Ω EOL resistor (provided
with the panel) and has an operating range of 8.8 to 14.2 VDC.
Power is dropped from zone 10 any
Detector
I D
Base
I D
# of
Detectors
Manufacturer
Model
Base
time a Sensor Reset is performed on
the panel. Whenever non-Fire and
non-Supervisory zone types are used
on zone 10, make the appropriate
adjustments to the zone's Armed
Action to prevent false alarms from
occurring.
Detection Systems
DS282
B
B
None
None
N/A
N/A
A
10
10
10
10
10
12
7
Detection Systems DS282TH
Detection Systems DS250
B
MB2W
Detection Systems DS250TH
Detection Systems DS250HD
B
MB2W, MB2WL
MB2W, MB2WL
None
A
B
A
Sentrol/ESL
DMP/Hochiki
DMP/Hochiki
Hochiki
429AT
SLK-835
SLK-835H
SLK-12
S09A
HD-5
HD-5
HD-4
N/A
HSB-200, HSB-200N HB-55
HSB-200, HSB-200N HB-55
HSB-12-1, HSB-12-1N HB-80
The UL compatibility identifier is: A.
7
20
Figure 4: Compatible 2-wire smoke detectors
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Annunciator Outputs
12.1 Description
The four annunciator outputs can be programmed to indicate the activity of the panel's zones or conditions
occurring on the system. Annunciator outputs do not provide a voltage but instead switch to ground
voltage from another source. The outputs can respond to any of the conditions listed below:
1) Activation by zone condition: Steady, Pulse, Momentary, or Follower
2) Manually from the Security Command keypad
3) Communication failure
4) Armed area annunciation
5) Fire Alarm or Fire Trouble
7) Ambush alarm
8) Exit and Entry timers
9) System Ready
10) Ground start activation
12.2 Harness wiring
The open collector outputs are accessible by installing the DMP 300 Harness on the 4-pin header labeled J11.
The output locations are shown below:
Output
Color
Red
Yellow
Green
Black
Wire
1
2
3
4
1
2
3
4
Devices connected to the outputs must be located within the same room as the XR10/XR20 panel.
Telephone RJ Connector
13.1 Description
Connect the panel to the public telephone network by installing a DMP 356 RJ Cable between the panel's J4
connector and the RJ31X or RJ38X phone jack.
13.2 FCC registration
The Model XR10/XR20 complies with FCC part 68 and is registered with the FCC.
Registration number: CCKUSA - 18660 - AL - R
Ringer Equivalence: 1.1B
13.3 Notification
Registered terminal equipment must not be repaired by the user. In case of trouble, the device must be
immediately unplugged from the telephone jack. The factory warranty provides for repairs. Registered terminal
equipment may not be used on party lines or in connection with coin telephones. Notification must be given to
the telephone company of:
a. The particular line(s) the service is connected to
b. The FCC registration number
c. The ringer equivalence
d. The make, model, and serial number of the device
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
13.4 Ground start
To configure the XR10/XR20 for ground start operation, you must install the appropriate ground start module and
program one of the panel's available annunciator outputs for Ground Start operation. Refer to the XR10/XR20
Programming Guide for complete programming information.
Reset Jumpers J16
14.1 Description
There are two reset jumpers located at the top right of the panel's circuit board labeled RESET. Momentarily
shorting these jumpers allows you to reset the microprocessor of the XR10/XR20. Resetting the panel allows
you to enter the panel's internal Programmer.
To reset the panel when first installing the system, place the blade of a slotted screwdriver across the two reset
jumpers after applying power to the panel.
To reset the panel while the system is operational (for example, prior to reprogramming), you can short the
jumpers without powering down the system.
After resetting the panel for programming, you must begin within 30 minutes. If you wait longer than 30 minutes,
you'll have to reset the panel again.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
UNIVERSAL UL BURGLARY SPECIFICATIONS
15.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
XR10/XR20 panel in accordance with any of the UL burglary standards. Additional specifications may be
required by a particular standard.
15.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70, UL 681, and UL 611 for all burglary installations.
15.3 Police station phone numbers
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
15.4 Bypass reports
The bypass reports option must be programmed as YES for all UL burglary applications. See section 5.5 of the
XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
15.5 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end
user is essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance
program and acquainting the user with the correct procedure for use and testing of the system is also the
responsibility of the installing alarm company.
15.6 Cross zoning
Zones used for cross zoning must be installed to allow detection of the same event. Cross zoning shall not
conflict with UL 681 or 1641.
15.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
15.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB,
Osborne-Hoffman Quick-Alert and Radionics D6500 receivers.
UL 1023 SPECIFICATIONS
Household Burglar-Alarm System Units
16.1 Bell cutoff
The bell cutoff time cannot be less than five minutes. See section 7.2 of the XR10 Programming Guide (LT-0230)
and XR20 Programming Guide (LT-0305).
16.2 Entry delay
The maximum entry delay used must not be more than 45 seconds. See section 6.4 of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
16.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See section 6.5 of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
16.4 Zone expansion on 4-wire bus
When expansion zones are used, the keypad and zone
Normally Closed
+
Voltage output
expander 4-wire bus must be limited to three feet in length
from terminal 11
Normally Open
unless an external communication fail indicator is added. A
–
Zone activated
annunciator output
Common
12 VDC relay may be wired as a communication fail
indicator. To install, connect the negative side of the
indicator to one of the panel's annunciator outputs and the
positive side to the smoke power (terminal 11 of the XR10/
XR20 panel). See section 7.5C of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
+
–
Voltage output
from terminal 11
1k Ohm
Device Fail LED
Zone activated
annunciator output
In addition to the wiring described above, a 24 hour zone must be programmed to activate the appropriate
annunciator output.
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
UL 1610 and 1076 SPECIFICATIONS
Central-Station and Proprietary Burglar-Alarm Units
17.1 Opening/Closing reports
The Opening/Closing Reports option must be programmed as YES. See section 5.2 of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
17.2 Automatic bell test
This option must be programmed as YES. See section 7.3 of the XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
17.3 Proprietary dialer
The Model XR10/XR20 provides Grade A proprietary service when configured as a digital dialer.
UL 1635 SPECIFICATIONS
Digital Burglar Alarm Communicator System Units
18.1 Digital Dialer telephone number
Both programmed telephone numbers must begin with a D or P. See sections 3.17 and 3.18 of the XR10
Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.2 Entry delay
The maximum entry delay used must not be more than 60 seconds. See section 6.4 of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.3 Exit delay
The maximum exit delay used must not be more than 60 seconds. See section 6.5 of the XR10 Programming
Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.4 Test frequency
The Test Frequency option must be programmed so that the XR10 sends a report once every 24 hours. See
section 3.6 of the XR10 Programming Guide (LT-0230) and XR20 Programming Guide (LT-0305).
18.5 Automatic bell test
This option must be programmed as YES. See section 7.3 of the XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
18.6 Grade B Central Station
Grade B Central Station service can be provided under UL 1635 by adding a Grade A local audible signal
appliance and placing the Model XR10/XR20 panel into the Model 349A Grade A Attack Resistant Housing.
UL 365 and 609 SPECIFICATIONS
Police Station Connected and Local Burglar Alarm Units and Systems
19.1 Entry delay
The maximum entry delay used must not be more than 60 seconds when using the Model 349A Grade A
housing. See section 6.4 of the XR10 Programing Guide (LT-0230) and XR20 Programming Guide (LT-0305).
19.2 Grade A bell
A Grade A local audible signal appliance must be used.
19.3 Bell cutoff
The bell cutoff time cannot be less than 15 minutes. See section 7.2 of the XR10 Programming Guide (LT-0230)
and XR20 Programming Guide (LT-0305).
19.4 Automatic bell test
The Automatic Bell Test option must be programmed as YES. See section 7.3 of the XR10 Programming Guide
(LT-0230) and XR20 Programming Guide (LT-0305).
19.5 Grade A Mercantile
For Grade A Mercantile and Police Station Connect operation the Model XR10/XR20 must be mounted in a
Grade A attack resistant housing, (DMP Model 349A).
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
19.6 Mercantile Safe and Vault
When the DMP Model 349A housing is used, the XR10/XR20 provides operation as a mercantile safe and vault
alarm. Bell Supervision and wiring must be in accordance with UL 681. If the Model XR10/XR20 is mounted
outside the safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors
should be used. The XR10/XR20 does not provide operation as a Bank Safe and vault alarm.
19.7 Line security for Police Connect
Basic line security is provided when the Model XR10/XR20 is configured as a dialer system.
UNIVERSAL UL and NFPA FIRE ALARM SPECIFICATIONS
20.1 Introduction
The programming and installation specifications contained in this section must be completed when installing the
Model XR10/XR20 in accordance with any of the UL or NFPA fire standards. Additional specifications may be
required by a particular standard.
20.2 Wiring
All wiring must be in accordance with NEC, ANSI/NFPA 70.
20.3 Police station phone number
The digital dialer telephone number programmed for communication must not be a police station phone number,
unless that phone number is specifically provided for that purpose.
20.4 System maintenance
Proper installation and regular maintenance by the installing alarm company and frequent testing by the end user
is essential to ensure continuous satisfactory operation of any alarm system. Offering a maintenance program
and acquainting the user with the correct procedure for use and testing of the system is also the responsibility of
the installing alarm company.
20.5 Audible alarm
Fire Type zones should be programmed to activate an audible alarm. The Bell Action for Fire Type zones should
not be programmed as “N”. See section 7.4A in the XR10 Programming Guide (LT-0230) and XR20
Programming Guide (LT-0305).
20.6 Fire zone programming
Fire zones must be programmed to activate a trouble on open conditions and an alarm on short conditions. The
swinger bypass function must not be used on any fire zones. See section 8.8 in the XR10 Programming Guide
(LT-0230) and XR20 Programming Guide (LT-0305).
20.7 Ground Start
Ground Start phone lines must not be used for UL listed systems.
20.8 UL Listed Receivers
UL has verified operation with the DMP SCS-1 Security Receiver, Sur-Gard SG-HLR2-DG, FBII CP220PB,
Osborne-Hoffman Quick-Alert and Radionics D6500 receivers.
UL 985 NFPA 72 (chapter 2) SPECIFICATIONS
Household Fire Warning System Units
21.1 Bell output definition
The bell output of the Model XR10/XR20 must be programmed to operate steady on burglary alarms and pulsed
on fire alarms. See sections 7.4A and 7.4B of the XR10 Programming Guide (LT-0230) and XR20 Programming
Guide (LT-0305).
XR10/XR20 Installation Guide
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
CALIFORNIA STATE FIRE MARSHAL SPECIFICATIONS
22.1 Bell output definition
The bell output of the Model XR10/XR20 must be programmed to operate steady on burglary alarms and pulsed
on fire alarms. See sections 7.4A and 7.4B of the XR10 Programming Guide (LT-0230) and XR20 Programming
Guide (LT-0305).
Troubleshooting Section
23.1 Description
This section of the XR10/XR20 Installation Guide provides troubleshooting information for use when installing or
servicing an XR10/XR20 system.
Problem
Possible Cause
Solution
Remove the J16 reset jumper.
J16 reset jumper is installed.
Check for broken or shorted wires
between the keypad and panel.
Open or short on the green data
wire to the keypad.
Security Command keypads
display " SERVICE REQUIRED"
Replace with a new or repaired
keypad or zone expander.
Bad keypad or zone expander.
Open or short condition on the
yellow data wire.
Check for broken or shorted
wires.
Keypad display is not functional.
When a key is pressed, only a
short beep is emitted.
Bad keypad or zone expander.
Replace with a new or repaired
keypad or zone expander.
Set each keypad to a different
address to match the Device
Setup programming.
Keypad beeps when keys are
pressed but won't allow the user
to arm or enter the User Menu.
Two or more keypads are
assigned to the same address.
No jumper installed on phone jack
terminals 2 and 7.
Install a jumper across terminals 2
and 7 on the phone jack.
Keypad displays PHONE LINE
1 TROUBLE.
Digital Monitoring Products
2841 E. Industrial Drive Springfield, MO 65802-6310 800-641-4282
Download from Www.Somanuals.com. All Manuals Search And Download.
|