Cypress Clock FS781 User Manual

FS781/82/84  
Low EMI Spectrum Spread Clock  
Features  
Functional Description  
The Cypress FS781/82/84 are Spread Spectrum clock  
generator ICs (SSCG) designed for the purpose of reducing  
electromagnetic interference (EMI) found in today’s  
high-speed digital systems.  
• Spread Spectrum clock generator (SSCG) with 1×, 2×,  
and 4× outputs  
• 6- to 82-MHz operating frequency range  
• Modulates external clocks including crystals, crystal  
oscillators, or ceramic resonators  
The FS781/82/84 SSCG clocks use a Cypress-proprietary  
technology to modulate the input clock frequency, XIN, by  
modulating the frequency of the digital clock. By modulating  
the reference clock the measured EMI at the fundamental and  
harmonic frequencies of FSOUT is greatly reduced. This  
reduction in radiated energy can significantly reduce the cost  
of complying with regulatory requirements without degrading  
digital waveforms.  
• Programmable modulation with simple R-C external  
loop filter (LF)  
• Center spread modulation  
• 3V-5V power supply  
• TTL-/CMOS-compatible outputs  
• Low short-term jitter  
The Cypress FS781/82/84 clocks are very simple and  
versatile devices to use. By programming the two range select  
lines, S0 and S1, any frequency from 6- to 82-MHz operating  
range can be selected. The FS781/2/4 are designed to  
operate over a very wide range of input frequencies and  
provides 1×, 2×, and 4× modulated clock outputs.  
• Low-power Dissipation  
— 3.3 VDC = 37 mW – typical  
— 5.0 VDC = 115 mW – typical  
• Available in 8-pin SOIC and TSSOP packages  
The FS78x devices have a simple frequency selection table  
that allows operation from 6 MHz to 82 MHz in four separate  
ranges. The bandwidth of the frequency spread at FSOUT is  
determined by the values of the loop filter components. The  
modulation rate is determined internally by the input frequency  
and the selected input frequency range.  
Applications  
• Desktop/notebook computers  
• Printers, copiers, and MFP  
• Scanners and fax  
The Bandwidth of these products can be programmed from as  
little as 1.0% up to as much as 4.0% by selecting the proper  
loop filter value. Refer to the Loop Filter Selection chart in  
Table 2 and Table 3 for the recommended values. Due to a  
wide range of application requirements, an external loop filter  
(LF) is used on the FS78x products. The user can select the  
exact amount of frequency modulation suitable for the appli-  
cation. Using a fixed internal loop filter would severely limit  
the use of a wide range of modulation bandwidths (Spread %)  
to a few discrete values. Refer to FS791/2/4 products for appli-  
cations requiring 80- to 140-MHz frequency range.  
• LCD displays and monitors  
• CD-ROM, VCD, and DVD  
• Automotive and embedded systems  
• Networking, LAN/WAN  
• Digital cameras and camcorders  
• Modems  
Benefits  
• Programmable EMI reduction  
• Fast time to market  
• Lower cost of compliance  
• No degradation in rise/fall times  
• Lower component and PCB layer count  
Cypress Semiconductor Corporation  
Document #: 38-07029 Rev. *F  
198 Champion Court  
San Jose, CA 95134-1709  
408-943-2600  
Revised January 2, 2005  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
[1, 2, 3, 4]  
Table 2. FS781/82/84 Recommended Loop Filter Values C7 (pF) @ +3.3 VDC ±5% (R6 = 3.3K)  
[3]  
[3]  
[3]  
[3]  
[3]  
[3]  
[3]  
Input MHz S1 S0 BW = 1.0%  
BW = 1.5% BW = 2.0% BW = 2.5% BW = 3.0% BW = 3.5% BW = 4.0%  
6
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
10,000/1000  
10,000/330  
1040  
830  
1550  
990  
680  
420  
230  
980  
750  
730  
640  
400  
300  
230  
180  
170  
860  
820  
690  
600  
620  
680  
580  
440  
360  
325  
270  
250  
210  
185  
220  
860  
850  
760  
750  
740  
780  
770  
720  
670  
620  
540  
910  
820  
460  
300  
200  
760  
580  
470  
410  
250  
220  
180  
140  
120  
640  
620  
520  
420  
380  
400  
270  
260  
250  
220  
200  
185  
165  
150  
150  
560  
540  
560  
500  
470  
470  
470  
440  
270  
260  
250  
780  
640  
360  
220  
160  
580  
470  
390  
270  
210  
180  
150  
120  
100  
520  
470  
410  
340  
275  
250  
220  
210  
190  
185  
170  
150  
130  
120  
120  
410  
400  
350  
320  
370  
300  
280  
240  
210  
210  
210  
700  
520  
300  
200  
140  
470  
415  
320  
230  
180  
150  
130  
100  
82  
640  
450  
240  
190  
100  
410  
370  
220  
200  
160  
140  
100  
80  
560  
400  
210  
170  
80  
8
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
46  
48  
50  
52  
54  
56  
58  
60  
62  
64  
65  
66  
68  
70  
72  
74  
76  
78  
80  
82  
580  
10000  
1200  
1000  
960  
385  
300  
190  
180  
150  
120  
70  
920  
660  
470  
470  
60  
330  
68  
47  
10000  
2200  
1500  
960  
430  
400  
340  
280  
230  
210  
190  
180  
170  
155  
140  
120  
100  
100  
100  
340  
330  
260  
260  
300  
250  
230  
210  
190  
190  
190  
380  
330  
290  
220  
210  
190  
180  
160  
150  
135  
130  
85  
330  
290  
240  
160  
180  
170  
165  
140  
140  
120  
100  
47  
940  
950  
900  
790  
660  
470  
470  
445  
430  
65  
33  
295  
90  
82  
270  
82  
68  
1180  
1180  
1180  
1180  
1120  
1160  
1110  
1000  
910  
290  
280  
220  
230  
240  
220  
210  
190  
170  
170  
170  
230  
220  
210  
210  
170  
190  
190  
170  
160  
156  
150  
900  
900  
Notes:  
1. If the value selected from the above chart is not a standard, use the next available larger value.  
2. All bandwidths indicated above are total peak-to-peak spread. 1% = +0.5% to –0.5%. 4% = +2.0% to –2.0%.  
3. If C8 is not listed in the chart for a particular bandwidth and frequency, it is not used in the loop filter.  
4. Contact Cypress for LF values less than 1.0% bandwidth.  
Document #: 38-07029 Rev. *F  
Page 3 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
[1, 2, 3, 4]  
Table 3. FS781/82/84 Recommended Loop Filter Values C7 (pF) @ +5.0 VDC ±5% (R6 = 3.3K)  
[3]  
[3]  
[3]  
[3]  
[3]  
[3]  
[3]  
Input MHz S1 S0 BW = 1.0%  
BW = 1.5% BW = 2.0% BW = 2.5% BW = 3.0% BW = 3.5% BW = 4.0%  
6
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1140  
1170  
1030  
760  
1030  
970  
660  
340  
240  
970  
870  
680  
560  
360  
270  
230  
200  
1000  
990  
970  
880  
800  
680  
560  
420  
280  
330  
340  
280  
210  
220  
240  
800  
720  
630  
690  
650  
575  
500  
550  
600  
570  
540  
930  
740  
430  
230  
180  
730  
650  
480  
330  
250  
210  
180  
150  
740  
710  
670  
560  
460  
360  
260  
280  
200  
200  
205  
180  
160  
250  
120  
580  
490  
400  
365  
330  
340  
355  
330  
290  
240  
250  
830  
570  
350  
200  
140  
590  
510  
370  
260  
200  
170  
150  
110  
570  
520  
480  
380  
290  
260  
220  
210  
190  
180  
170  
140  
120  
110  
90  
710  
460  
280  
180  
100  
480  
430  
280  
230  
180  
150  
110  
100  
470  
420  
380  
310  
240  
220  
200  
180  
170  
160  
140  
110  
100  
90  
610  
400  
210  
160  
70  
510  
280  
130  
130  
50  
8
10  
12  
14  
16  
18  
20  
22  
24  
26  
28  
30  
32  
34  
36  
38  
40  
42  
44  
46  
48  
50  
52  
54  
56  
58  
60  
62  
64  
66  
68  
70  
72  
74  
76  
78  
80  
82  
450  
2490  
2490  
1360  
990  
430  
370  
190  
200  
160  
110  
100  
90  
370  
310  
250  
190  
150  
90  
820  
530  
430  
90  
250  
80  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
1030  
790  
410  
360  
310  
270  
230  
200  
190  
170  
140  
130  
120  
110  
90  
370  
300  
230  
220  
220  
190  
170  
140  
120  
110  
90  
1110  
1110  
830  
560  
510  
90  
470  
90  
450  
80  
80  
430  
80  
80  
70  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
Note 4  
430  
375  
320  
285  
250  
250  
245  
230  
220  
210  
200  
330  
285  
240  
225  
210  
210  
205  
200  
190  
185  
180  
250  
200  
150  
170  
190  
190  
180  
175  
170  
165  
160  
180  
140  
100  
140  
180  
170  
165  
160  
155  
150  
140  
Document #: 38-07029 Rev. *F  
Page 4 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Table 4. Modulation Rate Divider Ratios  
S1  
0
S0  
0
Input Frequency Range (MHz)  
Modulation Divider Number  
6 to 16  
16 to 32  
32 to 66  
66 to 82  
120  
240  
480  
720  
0
1
1
0
1
1
quently, higher energy peaks. Regulatory agencies test  
electronic equipment by the amount of peak energy radiated  
from the equipment. By reducing the peak energy at the funda-  
mental and harmonic frequencies, the equipment under test is  
able to satisfy agency requirements for EMI. Conventional  
methods of reducing EMI have been to use shielding, filtering,  
multi-layer PCBs, etc. These FS781/2 and 4 reduce the peak  
energy in the clock by increasing the clock bandwidth and  
lowering the Q of the clock.  
SSCG Modulation Profile  
The digital control inputs S0 and S1 determine the modulation  
frequency of FS781/2/4 products. The input frequency is  
divided by a fixed number, depending on the operating range  
that is selected. The modulation frequency of the FS78x can  
be determined from Table 4. To compute the modulation  
frequency, determine the values of S0 and S1, and find the  
modulation divider number in Table 4.  
SSCG  
Theory of Operation  
The FS781/82/84 products use a unique method of modulating  
the clock over a very narrow bandwidth and controlled rate of  
change, both peak to peak and cycle to cycle. The FS78x  
products take a narrow band digital reference clock in the  
range of 6–82 MHz and produce a clock that sweeps between  
a controlled start and stop frequency and precise rate of  
change. To understand what happens to an SSCG clock,  
consider that we have a 20-MHz clock with a 50% duty cycle.  
From a 20-MHz clock we know the following:  
The FS781/82/84 devices are phase-locked loop-(PLL)-type  
clock generators using Direct Digital Synthesis (DDS). ‘By  
precisely controlling the bandwidth of the output clock, the  
FS781/2/4 products become a low-EMI clock generator. The  
theory and detailed operation of these products will be  
discussed in the following sections.  
EMI  
All clocks generate unwanted energy in their harmonics.  
Conventional digital clocks are square waves with a duty cycle  
that is very close to 50%. Because of the 50/50 duty cycle,  
digital clocks generate most of their harmonic energy in the  
odd harmonics (e.g., third, fifth, seventh). It is possible to  
reduce the amount of energy contained in the fundamental  
and harmonics by increasing the bandwidth of the funda-  
mental clock frequency. Conventional digital clocks have a  
very high Q factor, which means that all of the energy at that  
frequency is concentrated in a very narrow bandwidth, conse-  
Clock Frequency = Fc = 20 MHz.  
Clock Period = Tc = 1/20 MHz = 50 ns.  
Consider that this 20-MHz clock is applied to the X input of  
IN  
the FS78x as either an externally driven clock or the result of  
a parallel resonant crystal connected to pins 1 and 2 of the  
FS78x. Also consider that the products are operating from a  
5V DC power supply and the loop filter is set for a total  
bandwidth spread of 2%. Refer to Figure 2.  
+ .5%  
1.0%Xin  
Total  
- .5%  
TIME (microseconds)  
[5]  
Figure 1. Frequency Profile in Time Domain  
Note:  
5. With the correct loop filter connected to Pin 4, the following profile will provide the best EMI reduction. This profile can be seen on a Time Domain Analyzer.  
Document #: 38-07029 Rev. *F  
Page 5 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
50%  
50%  
Tc = 50 ns.  
Figure 2. 20-MHz Unmodulated Clock  
From the above parameters, the output clock at FSOUT will be  
sweeping symmetrically around a center frequency of 20 MHz.  
Tc =49.50 ns.  
Tc = 50.50 n  
The minimum and maximum extremes of this clock will be  
+200 kHz and –200 kHz. So we have a clock that is sweeping  
from 19.8 MHz to 20.2 MHz and back again. If we were to look  
at this clock on a spectrum analyzer we would see the picture  
in Figure 3. Keep in mind that this is a drawing of a perfect  
clock with no noise.  
Figure 4. Period Comparison Chart  
Looking at Figure 3, you will note that the peak amplitude of  
the 20-MHz non-modulated clock is higher than the wideband  
modulated clock. This difference in peak amplitudes between  
modulated and unmodulated clocks is the reason why SSCG  
clocks are so effective in digital systems. This figure refers to  
the fundamental frequency of a clock. A very important charac-  
teristic of the SSCG clock is that the bandwidth of the funda-  
mental frequency is multiplied by the harmonic number. In  
other words, if the bandwidth of a 20-MHz clock is 200 kHz,  
the bandwidth of the third harmonic will be 3 × 200, or 600 kHz.  
The amount of bandwidth is relative to the amount of energy  
in the clock. Consequently, the wider the bandwidth, the  
greater the energy reduction of the clock.  
Fc = 20 MHz  
Fmin =  
Fmax =  
19.8 MHz  
20.2 MHz  
Most applications will not have a problem meeting agency  
specifications at the fundamental frequency. It is the higher  
harmonics that usually cause the most problems. With an  
SSCG clock, the bandwidth and peak energy reduction  
increases with the harmonic number. Consider that the  
eleventh harmonic of a 20-MHz clock is 220 MHz. With a total  
spread of 200 kHz at 20 MHz, the spread at the eleventh  
harmonic would be 2.20 MHz, which greatly reduces the peak  
energy content. It is typical to see as much as 12- to 18-dB  
reduction at the higher harmonics, due to a modulated clock.  
Figure 3. Spectrum Analysis of 19.8–20.2 MHz Clock  
We see that the original 20-MHz reference clock is at the  
center frequency (Cf), and the min. and max. extremes are  
positioned symmetrically about the center frequency. This type  
of modulation is called Center-Spread. Figure 4 shows a  
20-MHz clock as it would be seen on an oscilloscope. The top  
trace is the non-modulated reference clock. The bottom trace  
is the modulated clock at pin 6. From this comparison chart  
you can see that the frequency is decreasing and the period  
of each successive clock is increasing. The Tc measurements  
on the left and right of the bottom trace indicate the max. and  
min. extremes of the clock. Intermediate clock changes are  
small and accumulate to achieve the total period deviation.  
The reverse of this figure would show the clock going from  
minimum extreme back to the high extreme.  
The difference in the peak energy of the modulated clock and  
the non-modulated clock in typical applications will see a  
2 – 3 dB reduction at the fundamental and as much as 8 – 10  
dB reduction at the intermediate harmonics: third, fifth,  
seventh, etc. At the higher harmonics, it is quite possible to  
reduce the peak harmonic energy, compared to the unmodu-  
lated clock, by as much as 12 to 18 dB.  
Application Notes and Schematic  
Figure 5 is configured for the following parameters:  
Package selected = FS781.  
X
= 20-MHz crystal  
IN  
FSOUT = 20 MHz (S0 = 1 and S1 = 0).  
Bandwidth of the FSOUT clock is determined by the values of  
the loop filter connected to pin 4.  
Document #: 38-07029 Rev. *F  
Page 6 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Crystal is 20 MHz is 1st Order  
with 18 pF load capacitance.  
C2  
1
8
7
VDD  
Xin  
VDD  
S0  
C1  
20 MHz  
Y1  
If Crystal load capacitance is  
different than 18 pF, C1 and C2  
must be re-calculated.  
0.1 uF  
27 pF  
C3  
2
Xout  
For third overtone crystals, a  
parallel or series resonant trap  
is required.  
FS781  
(SOIC)  
27 pF  
3
4
6
5
FSOUT  
S1  
LF  
FSOUT  
VSS  
Mount loop filter components as  
close to LF pin as possible.  
R6  
C7  
C8  
**  
** Occasionally, C8 is used to  
create a second pole for this loop  
filter. Refer to Loop Filter Selection  
table.  
.
Figure 5. FS781 Schematic  
Document #: 38-07029 Rev. *F  
Page 7 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Absolute Maximum Ratings[6]  
This device contains circuitry to protect the input against  
damage due to high static voltages or electric fields; however,  
precautions should be taken to avoid application of any  
voltage higher than the absolute maximum rated voltages to  
this circuit. For proper operation, V and V  
should be  
IN  
OUT  
constrained to the range, V < (V or V  
) < V . All digital  
SS  
IN  
OUT  
DD  
inputs are tied high or low internally. Refers to electrical speci-  
fications for operating supply range.  
Table 5. Absolute Maximum Ratings  
Parameter  
Description  
Min.  
3.0  
–0.3  
–0.3  
0
Max.  
Unit  
VDC  
VDC  
VDC  
°C  
V
Operating Voltage  
Input, relative to V  
6.0  
DD  
VIRvss  
VORvss  
TOP  
V
V
+ 0.3  
SS  
DD  
DD  
Output, relative to V  
+ 0.3  
SS  
Temperature, Operating  
Temperature, Storage  
Temperature, Junction  
+70  
TST  
–65  
+150  
+125  
°C  
T
°C  
J
Table 6. DC Electrical Characteristics V = 3.3V and 5.0V ±10%, X = 48 MHz, T = 0°C to 70°C  
DD  
IN  
A
Parameter  
Description  
Min.  
Typ.  
Max.  
Unit  
V
V
I
Input Low Voltage  
Input High Voltage  
Input Low Current  
Input High Current  
0.3 * V  
VDC  
VDC  
µA  
IL  
DD  
0.7 * V  
IH  
DD  
100  
100  
0.4  
IL  
I
µA  
IH  
V
V
V
V
Output Low Voltage I = 10 mA, V = 5V  
VDC  
VDC  
VDC  
VDC  
OL  
OH  
OL  
OH  
OL  
DD  
Output High Voltage I = 10 mA, V = 5V  
V
– 1.0  
OH  
DD  
DD  
Output Low Voltage I = 6 mA, V = 3.3V  
0.4  
OL  
DD  
Output High Voltage I = 5 mA, V = 3.3V  
2.4  
OH  
DD  
Rpd  
Rpu  
Resistor, Pull-down (Pin 7)  
60K  
60K  
125K  
125K  
8
200K  
200K  
Resistor, Pull-up (Pin 3)  
Input Capacitance (Pin 1)  
Output Capacitance (Pin 2)  
C
C
pF  
xin  
10  
38  
20  
25  
0
pF  
xout  
I
I
5V Dynamic Supply Current (CL = No Load)  
3.3V Dynamic Supply Current (CL = No Load)  
Short Circuit Current (FSOUT)  
mA  
mA  
mA  
%
CC  
CC  
ISC  
BW  
BW  
[7]  
BW% Variations, 3.30V  
–20  
–30  
+20  
+30  
[7]  
BW% Variations, 5.00V  
0
%
Table 7. Timing Electrical Characteristics V = 3.3V and 5.0V ±10%, T = 0°C to 70°C, C = 15 pF, X = 48 MHz  
DD  
A
L
IN  
Parameter  
tTLH  
Description  
Min.  
1.8  
1.5  
0.5  
0.5  
2.1  
1.7  
0.7  
0.6  
45  
Typ.  
Max.  
Unit  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
%
Output Rise Time Measured at 10%–90% @ 5 VDC  
Output Fall Time Measured at 10%–90% @ 5 VDC  
Output Rise Time Measured at 0.8V–2.0V @ 5 VDC  
Output Fall Time Measured at 0.8V–2.0 V @ 5 VDC  
Output Rise Time Measured at 10%–90% @ 3.3 VDC  
Output Fall Time Measured at 10%–90% @ 3.3 VDC  
Output Rise Time Measured at 0.8V–2.0V @ 3.3 VDC  
Output Fall Time Measured at 0.8V–2.0 V @ 3.3 VDC  
Output Duty Cycle  
2.2  
2.0  
2.7  
2.5  
0.8  
0.8  
3.2  
2.6  
1.2  
1.1  
55  
tTHL  
tTLH  
0.65  
0.65  
2.65  
2.1  
tTHL  
tTLH  
tTHL  
tTLH  
0.95  
0.85  
50  
tTHL  
TsymF1  
Notes:  
6. Single Power Supply: The Voltage on any input or /O pin cannot exceed the power pin during power-up.  
7. Percentage variations from the bandwidth % values given in Table 2 and Table 3.  
Document #: 38-07029 Rev. *F  
Page 8 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Table 7. Timing Electrical Characteristics V = 3.3V and 5.0V ±10%, T = 0°C to 70°C, C = 15 pF, X = 48 MHz (continued)  
DD  
A
L
IN  
Parameter  
CCJ  
Description  
Min.  
Typ.  
320  
310  
270  
390  
Max.  
370  
360  
325  
440  
Unit  
ps  
FSOUT, Cycle-to-Cycle Jitter, 48 MHz @ 3.30 VDC (Pin 6)  
FSOUT, Cycle-to-Cycle Jitter, 48 MHz @ 5.0 VDC (Pin 6)  
FSOUT, Cycle-to-Cycle Jitter, 72 MHz @ 3.30 VDC (Pin 6)  
FSOUT, Cycle-to-Cycle Jitter, 72 MHz @ 5.0 VDC (Pin 6)  
CCJ  
ps  
CCJ  
ps  
CCJ  
ps  
Table 8. Range Selection Table  
S1  
S0  
Fin (MHz)  
(pin 2/3)  
Modulation  
Rate  
FS781  
FS782  
FS784  
(pin 3)  
(pin 7)  
FSOUT (pin 6)  
FSOUT (pin 6)  
12–32 MHz  
32–64 MHz  
64–82 MHz  
N/A  
FSOUT (pin 6)  
32–64 MHz  
64–82 MHz  
N/A  
0
0
1
1
0
1
0
1
6–16  
16–32  
32–66  
66–82  
Fin/120  
Fin/240  
Fin/480  
Fin/720  
6–16 MHz  
16–32 MHz  
32–66 MHz  
66–82 MHz  
N/A  
Ordering Information[8]  
Part Number  
IMIFS781BZB  
Package Type  
Product Flow  
8-pin 150-mil SOIC  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
IMIFS781BZBT  
IMIFS782BZB  
8-pin 150-mil SOIC – Tape and Reel  
8-pin 150-mil SOIC  
IMIFS782BZBT  
IMIFS784BZB  
8-pin 150-mil SOIC – Tape and Reel  
8-pin 150-mil SOIC  
IMIFS784BZBT  
IMIFS781BT  
8-pin 150-mil SOIC – Tape and Reel  
8-pin (4.4 mm body) TSSOP  
IMIFS781BTT  
8-pin (4.4 mm body) TSSOP – Tape and Reel  
8-pin (4.4 mm body) TSSOP  
IMIFS784BT  
IMIFS784BTT  
8-pin (4.4 mm body) TSSOP – Tape and Reel  
Lead-free  
CYIFS781BSXC  
CYIFS781BSXCT  
CYIFS782BSXC  
CYIFS782BSXCT  
CYIFS784BSXC  
CYIFS784BSXCT  
CYIFS781BZXC  
CYIFS781BZXCT  
CYIFS782BZXC  
CYIFS782BZXCT  
CYIFS784BZXC  
8-pin 150-mil SOIC  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
Commercial, 0 to 70°C  
8-pin 150-mil SOIC – Tape and Reel  
8-pin 150-mil SOIC  
8-pin 150-mil SOIC – Tape and Reel  
8-pin 150-mil SOIC  
8-pin 150-mil SOIC – Tape and Reel  
8-pin (4.4 mm body) TSSOP  
8-pin (4.4 mm body) TSSOP – Tape and Reel  
8-pin (4.4 mm body) TSSOP  
8-pin (4.4 mm body) TSSOP – Tape and Reel  
8-pin (4.4 mm body) TSSOP  
CYIFS784BZXCT  
8-pin (4.4 mm body) TSSOP – Tape and Reel  
Note:  
8. The ordering part number differs from the marking on the actual device.  
Document #: 38-07029 Rev. *F  
Page 9 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Marking Example  
Cypress  
FS781BS  
Cypress  
FS781BT  
Date Code, Lot #  
Date Code, Lot #  
FS781 B S  
Package  
S = SOIC  
T = TSSOP  
Revision  
Cypress Device Driver  
Package Drawing and Dimensions  
8-lead (150-Mil) SOIC S8  
PIN 1 ID  
4
1
1. DIMENSIONS IN INCHES[MM] MIN.  
MAX.  
2. PIN 1 ID IS OPTIONAL,  
ROUND ON SINGLE LEADFRAME  
RECTANGULAR ON MATRIX LEADFRAME  
0.150[3.810]  
0.157[3.987]  
3. REFERENCE JEDEC MS-012  
4. PACKAGE WEIGHT 0.07gms  
0.230[5.842]  
0.244[6.197]  
PART #  
S08.15 STANDARD PKG.  
SZ08.15 LEAD FREE PKG.  
5
8
0.189[4.800]  
0.196[4.978]  
0.010[0.254]  
0.016[0.406]  
X 45°  
SEATING PLANE  
0.061[1.549]  
0.068[1.727]  
0.004[0.102]  
0.050[1.270]  
BSC  
0.0075[0.190]  
0.0098[0.249]  
0.004[0.102]  
0.0098[0.249]  
0°~8°  
0.016[0.406]  
0.035[0.889]  
51-85066-*C  
0.0138[0.350]  
0.0192[0.487]  
Document #: 38-07029 Rev. *F  
Page 10 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
FS781/82/84  
Package Drawing and Dimensions (continued)  
8-Lead Thin Shrunk Small Outline Package (4.40 MM Body) Z8  
PIN 1 ID  
1
DIMENSIONS IN MM[INCHES] MIN.  
MAX.  
6.25[0.246]  
6.50[0.256]  
4.30[0.169]  
4.50[0.177]  
8
0.65[0.025]  
BSC.  
0.25[0.010]  
BSC  
0.19[0.007]  
0.30[0.012]  
1.10[0.043] MAX.  
GAUGE  
PLANE  
0°-8°  
0.076[0.003]  
0.85[0.033]  
0.95[0.037]  
0.50[0.020]  
0.70[0.027]  
0.05[0.002]  
0.15[0.006]  
0.09[[0.003]  
0.20[0.008]  
SEATING  
PLANE  
2.90[0.114]  
3.10[0.122]  
51-85093-*A  
All product and company names mentioned in this document may be the trademarks of their respective holders.  
Document #: 38-07029 Rev. *F  
Page 11 of 12  
© Cypress Semiconductor Corporation, 2005. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use  
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be  
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its  
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress  
products in life-support systems application implDiesotwhantlothaedmfarnoumfacWturwerwa.sSsuommeasnaullarilssk.cofosmuc.hAulsleMaannduinadlsoinSgesaoricnhdeAmnndifieDsoCwypnrelosasda.gainst all charges.  
FS781/82/84  
Document History Page  
Document Title: FS781/82/84 Low EMI Spectrum Spread Clock  
Document Number: 38-07029  
Orig. of  
REV.  
**  
ECN NO. Issue Date Change  
Description of Change  
Convert from IMI to Cypress  
106948  
111654  
118355  
122679  
277189  
314274  
417662  
06/07/01  
02/27/02  
08/30/02  
12/14/02  
See ECN  
See ECN  
See ECN  
IKA  
IKL  
*A  
Add new marking suffix for SOIC packages. Converted to FrameMaker.  
Swap the location of S0 and S1 in tables 2 and 3 in pages 2,3 and 4.  
Add power up requirements to operating conditions information.  
Added Lead-free Devices  
*B  
RGL  
RBI  
*C  
*D  
*E  
RGL  
RGL  
RGL  
Fixed the Ordering Information to match the DevMaster  
Added Maximum Junction Temperature in Absolute Maximum Ratings table  
*F  
Document #: 38-07029 Rev. *F  
Page 12 of 12  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Cobra Electronics Cordless Telephone CP 9135 User Manual
Coleman Tent 2000001126 User Manual
Craftsman Work Light 315110990 User Manual
Curtis CD Player KCR2613P User Manual
Dell Server DP884 User Manual
Elation Professional Work Light LED 36 Pro User Manual
Fisher Price Baby Toy 77949 User Manual
Fundex Games Board Games Sybarit User Manual
GE Monogram Switch Zenith Controls User Manual
Global Machinery Company Automobile C4500 User Manual