Operator’s Manual
Models
724 STE
926 STE
Model 926 STE shown
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 368023 Cleveland, Ohio 44136-9722.
CUB CADET CORP. P.O. BOX 368023 CLEVELAND, OHIO 44136-9722
770-10008B
(6/2000)
PRINTED IN U.S.A.
FORM NO.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
This symbol points out important safety instructions which, if not followed, could endanger the personal
safety and/or property of yourself and others. Read and follow all instructions in this manual before
attempting to operate this machine. Failure to comply with these instructions may result in personal
injury. When you see this symbol—heed its warning.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle components contain or emit
chemicals known to State of California to cause cancer and birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Failure to observe the following safety instructions could result in serious injury or death.
7. Never attempt to make any adjustments while engine is
Training
running, except where specifically recommended in the
operator’s manual.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place
for future and regular reference and for ordering
replacement parts.
care in handling gasoline. Gasoline is extremely
2. Be familiar with all controls and their proper operation.
flammable and the vapors are explosive. Serious
Know how to stop the machine and disengage them
personal injury can occur when gasoline is spilled on
quickly.
yourself or your clothes which can ignite. Wash your skin
3. Never allow children under 14 years old to operate this
and change clothes immediately.
machine. Children 14 years old and over should read and
a. Use only an approved gasoline container.
understand the operation instructions and safety rules in
b. Extinguish all cigarettes, cigars, pipes and other
this manual and should be trained and supervised by a
parent.
4. Never allow adults to operate this machine without
proper instruction.
5. Thrown objects can cause serious personal injury. Plan
sources of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the
engine is hot or running.
e. Allow engine to cool at least two minutes before
your snow throwing pattern to avoid discharge of material
refueling.
f. Never over fill fuel tank. Fill tank to no more than
½ inch below bottom of filler neck to provide space
feet from the machine while it is in operation. Stop
for fuel expansion.
toward roads, bystanders and the like.
6. Keep bystanders, helpers, pets and children at least 75
machine if anyone enters the area.
7. Exercise caution to avoid slipping or falling, especially
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and
when operating in reverse.
equipment. Move machine to another area. Wait 5
minutes before starting the engine.
i. Never store the machine or fuel container inside
Preparation
where there is an open flame, spark or pilot light
1. Thoroughly inspect the area where the equipment is to
(e.g. furnace, water heater, space heater, clothes
be used. Remove all door mats, newspapers, sleds,
dryer etc.).
boards, wires and other foreign objects which could be
j. Allow machine to cool 5 minutes before storing.
tripped over or thrown by the auger/impeller.
2. Always wear safety glasses or eye shields during
Operation
operation and while performing an adjustment or repair to
protect your eyes. Thrown objects which ricochet can
cause serious injury to the eyes.
1. Do not put hands or feet near rotating parts, in the auger/
impeller housing or discharge chute. Contact with the
3. Do not operate without wearing adequate winter outer
rotating parts can amputate hands and feet.
garments. Do not wear jewelry, long scarves or other
loose clothing which could become entangled in moving
2. The auger/impeller clutch lever is a safety device. Never
bypass its operation. Doing so, makes the machine
parts. Wear footwear which will improve footing on
unsafe and may cause personal injury.
slippery surfaces.
4. Use a grounded three wire extension cord and receptacle
3. The clutch levers must operate easily in both directions
and automatically return to the disengaged position when
for all units with electric start engines.
released.
5. Adjust collector housing height to clear gravel or crushed
4. Never operate with a missing or damaged discharge
rock surfaces.
chute. Keep all safety devices in place and working.
6. Disengage all clutch levers before starting the engine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Never run an engine indoors or in a poorly ventilated
area. Engine exhaust contains carbon monoxide, an
odorless and deadly gas.
6. Do not operate machine while under the influence of
alcohol or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while
operating on slopes.
10. Plan your snow throwing pattern to avoid discharge
towards windows, walls, cars etc. To avoid property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders and pets
or allow anyone in front of the machine.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on
the handles. Walk, never run.
14. Disengage power to the auger/impeller when
transporting or not in use.
15. Never operate machine at high transport speeds on
slippery surfaces. Look down and behind and use care
when in reverse.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
Maintenance And Storage
1. Never tamper with safety devices. Check their proper
operation regularly.
2. Disengage all clutch levers and stop engine. Wait until
the auger/impeller come to a complete stop. Disconnect
the spark plug wire and ground against the engine to
prevent unintended starting before cleaning, repairing, or
inspecting.
3. Check bolts, and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original
equipment manufacturer’s (O.E.M.) parts only. Use of
parts which do not meet the original equipment
specifications may lead to improper performance and
compromise safety.
6. Check clutch controls periodically to verify they engage
and disengage properly and adjust, if necessary. Refer to
the adjustment section in this operator’s manual for
instructions.
7. Maintain or replace safety and instruction labels, as
necessary.
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace ,clothes dryer etc.
17. Disengage all clutch levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the discharge chute, making any
adjustments, or inspections.
18. Never put your hand in the discharge or collector
openings. Always use a clearing tool to unclog the
discharge opening.
11. Always refer to the operator’s manual for proper
instructions on off-season storage.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer or
telephone 1-800-528-1009 for assistance and the name
of your nearest servicing dealer.
Your Responsibility:
Restrict the use of this power machine to persons who read,
understand and follow the warnings and instructions in this
manual and on the machine. The safety labels are given
below for your reference.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: LOOSE PARTS
The snow thrower is shipped with the following loose parts in the carton. Please remove all loose parts from the
carton before discarding it. See below to identify the parts, noting that these parts may be referred to again in the
following sections of the manual. Part numbers are shown in parentheses.
Auger Shear Bolts
The augers are secured to the auger shaft with two shear bolts and
hex lock nuts. If you hit a foreign object or ice jam, the snow thrower
is designed so that the bolts may shear. Two replacement shear
Shear Bolts
(710-0890A)
Hex Lock Nuts bolts and nuts are provided for your convenience. Store in a safe
(712-0429)
place until needed.
IMPORTANT: NEVER replace the auger shear bolts with standard
hex bolts. Any damage to the auger gearbox or other components
as a result of doing so will NOT be covered by your snow thrower’s
warranty.
Figure 1
SECTION 3: ASSEMBLING YOUR SNOW THROWER
•
•
•
Model 926 STE: Secure the upper handle and
NOTE: Any reference in this manual to the left or right
side of the snow thrower is observed from the
operator’s position.
lower handle with the two plastic wing nuts, cupped
washers and carriage bolts previously removed and
tighten the upper two plastic wing nuts.
IMPORTANT: Make any final adjustments as instructed
later on in this section BEFORE operating your snow
thrower. Failure to follow the instructions may cause
damage to the snow thrower.
Model 724 STE: Secure the upper handle and
lower handle with the two plastic wing knobs,
cupped washers and carriage bolt (eyebolt on left
side) previously removed. See Figure 3.
Model 724 STE: Adjust the eyebolt on the chute
directional control so the rod does not come into
contact with the engine by moving the hex nut
against the handle (if necessary). Retighten the
wing nut to secure the directional control in this
position.
•
•
•
•
Remove the screws from the top, sides, and ends
of the shipping carton.
Set the panels aside to avoid tire punctures or
personal injury.
Remove and discard the plastic bag that covers the
unit.
Roll the unit out of the carton.
•
Slide the shift rod connector down over the end of
the lower shift rod. See Figure 3. Tap the connector
until it locks over the lower shift rod.
WARNING: Disconnect the spark plug
and ground it against the engine to prevent
unintended starting.
•
•
Model 926 STE: Remove the lower two plastic
wing nuts, cupped washers and carriage bolts from
each side of the lower handle. See Figure 2.
Model 724 STE: Remove the lower two plastic
wing nuts, cupped washers and carriage bolt
(eyebolt on the left side) from the lower handle.
See Figure 2.
Upper Handle
Eyebolt
•
•
Raise the upper handle assembly until it locks over
the lower handle. See Figure 3.
Look at the lower rear of the snow thrower frame to
be sure all the cables are aligned with the cable
roller guides.
Lower Handle
Wing Knobs, Washers,
& Bolts
Model 724 STE shown
Figure 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Loosen the jam nut and thread the cable in (for less
slack) or out (for more slack) as necessary. See
Figure 5 .
Recheck the adjustment before retightening the
jam nut against the cable.
Shift Rod
Hex Nut
Eyebolt
Connector
Traction Control and Shift Lever Adjustment
NOTE: It is easier to maneuver a non-running snow
thrower with both track steering controls held in
simultaneously.
To check the adjustment of the traction control and shift
lever, proceed as follows:
Wing Knobs
•
Move the shift lever into the sixth (6) position.
a. With the traction control (see Figure 7 )
released, push the snow thrower forward,
then pull it back. Disregarding the overall
weight of the snow thrower, the machine
should otherwise move freely.
Lower
Shift Rod
Figure 3
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or change directions.
b. Engage the traction control, and attempt to
move the machine both forward and
rearward. You should experience resistance
as the wheels should not be turning.
Move the shift lever into the fast reverse (R2)
position and repeat the previous steps (a & b).
•
If not already attached, slip the cables that run from
the handle panel to the chute into the cable guide
located on top of the engine. See Figure 4.
•
Cable Guide
If you experienced resistance either when repositioning
the shift lever (see Figure 7 ) from position 6 to R2 or
when attempting to move the machine forward or
rearward with the traction control released, your snow
thrower’s traction control is in need of adjustment and
you should NOT operate the snow thrower before
completing the adjustment as follows:
Figure 4
•
•
•
Unwrap the headlight wire, which is attached to the
headlight beneath the handle panel.
Wind the headlight wire around the right handle
until excess slack is removed.
Plug the wire from the right side of the engine,
beneath the fuel tank.
Final Adjustments
Auger Control Adjustment
“Z” End
Jam Nut
Check the adjustment of the auger control as follows:
•
Push forward on the auger control (Refer to Figure
7 ) until the small rubber bumper contacts the upper
handle. There should be slack in the cable. See
Figure 5 .
•
Release the auger control. The cable should be
straight. Make certain you can depress the auger
control against the left handle completely without
using excess force.
Auger Control Cable
Figure 5
If adjustment is necessary, proceed as follows:
6
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Loosen the jam nut on the traction control cable
(located opposite the auger control cable) and
UNTHREAD the cable one full turn.
•
•
Loosen, but do NOT remove, the three hex nuts
which fasten the skid shoe to the auger housing.
Move the skid shoe to the desired position.
•
•
Recheck the adjustment.
Retighten the jam nut to secure the cable when the
correct adjustment is reached.
NOTE: Make certain the entire bottom surface of the
skidshoe is against the ground to avoid uneven wear on
the skid shoes.
If the machine can be moved freely both forward and
rearward with the traction control fully depressed,
proceed as follows:
•
•
Retighten the hex nuts loosened earlier.
Repeat this adjustment on the skid shoe found on
the opposite side of the snow thrower.
•
•
•
Loosen the jam nut on the traction drive cable and
THREAD the cable in one full turn.
Recheck the adjustment and repeat the adjustment
as necessary.
Retighten the jam nut to secure the cable when the
correct adjustment is reached.
NOTE: The skid shoes are reversible on this machine.
When one side wears out, it can be rotated 180° and
the other flat skid surface can be used.
NOTE: If you are uncertain that you have reached the
correct adjustment, refer to the Traction Control
Adjustment in the previous column.
Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by repositioning the skid shoes found on
either side of the snow throwers auger housing. For
smooth surface snow removal such as on an asphalt
driveway, place the skid shoes in a lower position. Use
a higher position when the area to be cleared is
uneven. See Figure 6.
Shave Plate
Carriage Bolts
IMPORTANT: When operating your snow thrower on a
gravel driveway, ALWAYS adjust the skid shoes into
the HIGHEST position.
Skid Shoes
High
Low
Hex Nuts
Figure 6
Adjust skid shoes as follows:
SECTION 4: KNOW YOUR SNOW THROWER
Shift Lever
The shift lever is located in the center of the handle
panel and is used to determine both ground speed and
direction of travel. It can be moved into any of eight
positions.
Auger
Control
Traction Control /
Auger Control Lock
Electric
Chute-Rotation
Switch
Heated Handles
Switch
Forward
Your snow thrower has six forward (F) speeds. Position
one (1) is the slowest and position six (6) is the fastest.
Handles
Reverse
Your snow thrower has two reverse (R) speeds. R1 and
R2, R2 is the faster speed.
Shift
Lever
IMPORTANT: Always release the traction control before
changing speeds.
Auger Control
Chute
Tilt
Control
The auger control is located on the left handle. See
Figure 7. Squeeze the auger control lever to engage
the augers. Release to stop the snow throwing action
(the traction control must also be released).
Right Track
Steering Control
Left Track
Steering Control
Model 926 STE shown
Figure 7
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Traction Control / Auger Control Lock
NOTE: The heated grips are a compliment, NOT a
substitute for proper cold weather outerwear for hands.
It is recommended that the user wear gloves/mittens
when operating this snow thrower.
The traction control is located on the right handle. See
Figure 7. Squeeze the traction control to engage the
wheel drive. Release to stop.
This same lever also locks the auger control so you
can operate the electric chute rotation switch without
interrupting the snow throwing process. If the auger
control is engaged simultaneously with the traction
control, the operator can release the auger control (on
the left handle) and the augers will remain engaged.
Release the traction control to stop the augers and
wheel drive (the auger control must also be released).
IMPORTANT: Toggle the heated handles switch to the
left into the OFF position after using the snow thrower.
Chute Tilt Control
The distance snow is thrown can be changed by
adjusting the angle of the chute assembly. Move the
chute tilt control forward to decrease the distance,
toward the rear to increase. See Figure 7.
Fuel Shut-Off Valve
The fuel shut-off valve, located under
the fuel tank, controls fuel flow from
the tank. Always make certain it is in
the Open (vertical) position before
attempting to start the engine.
Chute Directional Control (Model 724 STE)
The chute directional control is located on left side of
the snow thrower.
Closed
Open
To change the direction in which snow is thrown, turn
chute directional control as follows:
•
•
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
Track Lock Lever
The track lock lever is located on the right side of the
snow thrower and is used to select the position of the
auger housing and the method of track operation. See
Figure 8. Move the lever to the right, then forward or
backward to one of the three positions.
Electric Chute-Rotation Switch (Model 926 STE)
The electric chute-rotation switch is located on the left
side of the snow thrower handle panel.
To change the direction in which discharged snow is
thrown, proceed as follows:
Transport—Raises the front end of the snow thrower for
easy transport. Using proper caution, this position may
also be used on many gravel driveways to clear snow
while leaving gravel undisturbed.
•
Push the toggle switch to the left to rotate the chute
counterclockwise.
•
Push the toggle switch to the right to rotate the
chute clockwise.
Normal Snow—Allows the tracks to be suspended
independently for continuous ground contact.
IMPORTANT: Release the switch once the chute has
completed its rotation cycle in either direction. Failure to
do so can result in damage to the electric chute motor
and/or its drive gear.
Packed Snow—Locks the front end of the snow thrower
down to the ground for hard-packed or icy snow
conditions.
Track Steering Control
The left and right track steering controls are located on
the underside of the handles and are used to assist in
steering the snow thrower. See Figure 7. Squeeze the
right track control when turning right, squeeze the left
control when turning left. Operate your snow thrower in
open areas until you become familiar with these
controls.
Track
Lock Lever
NOTE: It is easier to maneuver a non-running snow
thrower with both track steering controls held in
simultaneously.
Packed
Snow
Transport
Normal
Snow
Heated Handles Switch (Model 926 STE)
The heated handles switch is located on the right side
of the snow thrower handle panel. See Figure 7. To
activate the heated handles, toggle the switch to the
right to generate heat within the handle grips.
Figure 8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Headlight
The headlight is on whenever the engine is running.
Primer
Choke
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine and will shut off the engine
when pushed down completely. See Figure 9.
Switch
Box
Safety Ignition Key
The safety ignition key must be fully inserted in the
switch before the unit will start. Remove the ignition key
when the snow thrower is not in use. See Figure 9.
Electric
Starter
Button
Ignition
Key
IMPORTANT: Do NOT attempt to turn the key.
Recoil
Starter
Handle
Throttle
Control
Figure 9
SECTION 5: OPERATING YOUR SNOW THROWER
all times to avoid the possibility of electric shock which
Before Starting
may cause injury to the operator. Follow all instructions
carefully. Determine that your house wiring is a three-
wire grounded system. Ask a licensed electrician if you
are not certain. If your house wiring system is not a
three-wire grounded system, do not use this electric
starter under any conditions. If your system is grounded
and a three-hole receptacle is not available at the point
your starter will normally be used, one should be
installed by a licensed electrician.
WARNING: Read, understand, and follow
all instructions and warnings on the machine
and in this manual before operating.
•
The spark plug wire was disconnected for safety
purposes during assembly. Attach spark plug wire
to spark plug before starting.
Gas And Oil Fill-Up
When connecting the power cord, always connect the
cord to the starter on the engine first, then plug the
other end into a three-hole grounded receptacle.
IMPORTANT: Although your snow thrower comes
shipped with oil already in the engine, you MUST check
the engine oil level as instructed in the separate engine
manual packed with your unit BEFORE starting the
engine for the first time. Read instructions carefully.
When disconnecting the power cord, always unplug the
end from the three-hole grounded receptacle first.
To Start Engine
Service the engine with gasoline and oil as
instructed in the separate engine manual packed with
your snow thrower. Read instructions carefully.
IMPORTANT: If the unit shows any sign of motion
(traction drive or augers) with the controls disengaged,
shut the engine off immediately. Readjust as instructed
under Final Adjustments in Section 3 of this manual.
WARNING: Use extreme care when
handling gasoline. Gasoline is extremely
flammable and the vapors are explosive.
Never fuel machine indoors or while the
engine is hot or running. Extinguish
cigarettes, cigars, pipes and other sources of
ignition.
•
•
Attach the spark plug wire to the spark plug.
Make certain the fuel shut-off valve is in the open
(vertical) position.
•
•
Make certain that both the auger control and the
traction control are in the disengaged position.
Move the throttle control up to the FAST position.
Insert the ignition key into the slot. See Figure 9. Be
certain it snaps into place. Do not turn the key.
Rotate the choke knob to the FULL choke position
(cold engine start). If the engine is warm, place the
choke in the OFF position.
Electric Starter
WARNING: The electric starter is
equipped with a three-wire power cord and
plug, and is designed to operate on 120 volt
•
AC household current. It must be properly grounded at
9
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Connect the power cord (electric start) to the switch
box on the engine. Plug the other end of power cord
into a three-hole, grounded 120 volt AC receptacle.
Push the primer button three times. If the engine is
warm, push the primer button once only. See
Figure 9.
To Engage Track Drive
•
With the engine running near top speed, move the
shift lever into one of the six FORWARD positions
or two REVERSE positions. Select a speed
appropriate for the snow conditions that exist.
NOTE: Use slower speeds in higher snow and until
NOTE: Always cover the vent hole in the primer
button when pushing. Additional priming may be
necessary for cold starts if the temperature is below
15°F.
you are familiar with the operation of the snow thrower.
•
Squeeze the traction control against the right
handle and the snow thrower will move. Release it
and the drive motion will stop.
•
•
Electric Start: Push the starter button on the front
of the engine to turn the starter. When the engine
starts, release the starter button (see Figure 9).
Recoil Start: Grasp the starter handle (see Figure
9) and pull the rope out slowly until resistance is
felt. Pull the starter handle rapidly. Do not allow the
handle to snap back. Allow it to rewind slowly while
keeping a firm hold on the starter handle.
IMPORTANT: NEVER move the shift lever without first
releasing the traction control. Doing so will cause
premature wear to the drive system’s friction wheel.
To Engage Augers
To engage the augers and start the snow throwing
action, proceed as follows:
•
As the engine warms up and begins to operate
evenly, rotate the choke knob slowly to the OFF
position. If the engine falters, return to FULL choke,
then slowly move to the OFF position.
•
Squeeze the auger control against the left handle.
To disengage power to the augers:
•
Release both the auger control and the traction
control, if engaged.
The auger control can be locked so you can turn the
electric chute directional control without interrupting the
snow throwing process. Refer to Traction Control/
Auger Control Lock in Section 4 of this manual.
To Stop Engine
•
Run the engine for a few minutes after throwing
snow, to help dry off any moisture on the engine.
To help prevent possible freeze-up of the starter,
proceed as follows:
•
Operating Tips
Electric Starter: Connect the power cord to the
switch box on the engine, then connect to a 120
volt AC receptacle. With the engine running, push
the starter button and spin the starter for several
seconds. The unusual sound made by the spinning
starter will not harm the engine or starter.
Disconnect the power cord from receptacle first,
and then from the switch box.
NOTE: Allow the engine to warm up for a few minutes.
The engine will not develop full power until it reaches
operating temperature.
WARNING: Muffler and surrounding areas
of the engine become hot and can cause a
burn. Do not touch.
Recoil Starter: With the engine running, pull the
starter rope with a rapid, continuous full arm stroke
three or four times. Pulling the starter rope will pro-
duce a clattering sound, which is not harmful to the
engine or the recoil starter.
To stop the engine, push the throttle control lever
down to the stop position. Remove the ignition key
by pulling it straight out of the keyhole and
disconnect the spark plug wire from the spark plug
to prevent accidental starting while the equipment
is unattended.
•
For the most efficient snow removal, remove snow
immediately after it falls.
Discharge the snow downwind whenever possible.
Slightly overlap each previous path.
Set the skid shoes 1/4" below the shave plate for
normal usage. The skid shoes may be adjusted
upward (to lower the shave plate) for hard-packed
snow. Adjust downward (to raise the shave plate)
when using on gravel or crushed rock.
Be certain to follow the precautions found in the To
Stop Engine section to prevent possible freeze-up.
Clean the snow thrower thoroughly after each use.
•
•
•
•
•
•
NOTE: Do not lose the ignition key. Keep it in a safe
place. The engine will not start without the ignition key.
•
Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
the control levers back and forth several times.
Leave the throttle control lever in the STOP or OFF
position. Leave the choke control in the FULL
choke position. See Figure 9.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MAKING ADJUSTMENTS
WARNING: NEVER attempt to make adjustments
while the engine is running, except where specified in
the operator’s manual.
WARNING: Drain the gasoline out of your
snow thrower’s engine, or place a piece of
plastic film under the gas cap to avoid
spillage before making this adjustment.
Chute Directional Adjustment
•
•
•
Tip the snow thrower forward, allowing it to rest on
the auger housing.
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Refer to the
Chute Tilt Control in the Know Your Snow Thrower
Section.
Remove the frame cover underneath the snow
thrower by removing the six self-tapping screws.
With the traction control released, there must be
clearance between the friction wheel and the drive
plate in all positions of the shift lever.
Chute Directional Control And Support
Bracket Adjustment (Model 724 STE)
If the spiral at the bass of the chute directional control is
not fully engaging with the notches in the lower chute
assembly, the support bracket can be adjusted inward
or outward as follows:
Shift Lever
Hairpin
Clip
•
Loosen, but do NOT remove the hex nuts which
secure the chute directional control support bracket
to the snow thrower housing. See Figure 10.
Flat
Washer
Ferrule
Clutch Rod
Connector
Upper Shift Rod
Hairpin Clip
Spiral
Lower Shift Rod
Support
Hex Nuts
Bracket
Shift Arm
Figure 10
Figure 11
•
Adjust the support bracket inward or outward so
that the spiral is fully engaged in the notches on the
chute before retightening the hex nuts.
•
With the traction control engaged, the friction wheel
must contact the drive plate. See Figure 12.
If adjustment is necessary:
•
Loosen the jam nut on the traction drive cable (see
Figure 5). Adjust the cable as necessary.
Skid Shoe Adjustment
•
Retighten the jam nut to secure the cable when
correct adjustment is reached and reassemble.
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes. Refer
to Skid Shoe Adjustment in Section 3 of this manual.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it before operating the snow thrower.
Traction Control Adjustment
Refer to the information found under the heading Final
Adjustments in Section 3 of this manual to adjust the
traction control. If you are uncertain that you have
reached the correct adjustment, proceed as follows:
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Shift Rod Adjustment
To adjust the shift rod, proceed as follows.
Drive Shaft
•
Remove the hairpin clip and slide the clutch rod
connector up, to separate the upper shift rod from
the lower shift rod. See Figure 10.
Drive
Cable
Sprocket
Shaft
•
•
Place the shift lever into the sixth (6) position.
Rotate the shift arm clockwise (from the operator’s
position) as far as it will go.
•
•
Thread the upper shift rod downward until the
elbow on its lower end aligns with the hole found in
the lower shift rod.
Reconnect the upper shift rod to the lower shift rod
by reinserting the hairpin clip removed earlier and
sliding clutch rod connector back down into place.
Pivot
Rod
Friction
Wheel
Rubber
Drive
Plate
IMPORTANT: Make certain to check for correct
adjustment of the shift rod as instructed under the
heading Final Adjustments in Section 3 of this manual,
before operating the snow thrower.
Figure 12
Auger Control Adjustment
Refer to the information found under the heading Final
Adjustments in Section 3 of this manual to adjust the
auger control.
SECTION 7: MAINTAINING YOUR SNOW THROWER
Gear Shaft
Lubrication
Lubricate the gear shaft with 6-n-1 grease at least once
a season or after every 25 hours of operation (available
at automotive stores, or order part number 737-0170).
Refer to Figure 12.
WARNING: Disconnect the spark plug wire
and ground it against the engine before
performing any maintenance procedures.
IMPORTANT: Keep all grease and oil off of the rubber
friction wheel and aluminum drive plate.
Engine
Refer to the separate engine manual packed with your
unit for all engine lubrication instructions.
Drive and Shifting Mechanism
Lubricate at least once a season or after every 25 hours
of operation. Remove the frame cover, lubricate any
chains, sprockets, gears, bearings, shafts, and shifting
mechanism at least once a season. Use engine oil or a
spray lubricant. Avoid getting oil on the friction
wheel rubber and aluminum drive plate. Refer to
Figure 12.
WARNING: When following instructions in
the separate engine manual for draining oil,
be sure to protect the frame to avoid oil
dripping onto transmission parts.
Electric Chute-Rotation Motor (Model 926 STE)
The gear on the electric chute-rotation motor and the
base of the discharge chute itself should be lubed with
multi-purpose automotive grease once a season. See
Figure 13.
Lube Gear
and Chute Base
Auger Shaft
At least once a season, remove the shear bolts on the
auger shaft. Spray lubricant inside the shaft. See Figure
14. Also lubricate the plastic auger bearings at least
once a season and grease the fittings on the end of the
auger shaft with a standard grease gun.
Figure 13
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Traction Control / Auger Control Lock
Grease Fittings
The cams on the ends of the control rods which
interlock the traction drive and auger drive levers must
be lubricated at least once a season or every 25 hours
of operation. The cams can be accessed beneath the
handle panel. Use a multi-purpose automotive grease.
Vent Plug
Shear Bolts
Gear Case
The gear case is lubricated with grease at the factory.
Every 25 hours or once a season, remove the vent plug
located on the top of the gear case. If necessary, use a
grease gun on the gear case grease fitting. Lubricate
using Shell Alvania grease EPR00, part number 737-
0168. Refer to Figure 14.
IMPORTANT: Do not overfill the gear case. Damage to
the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
Plastic Bearings
Figure 14
SECTION 8: SERVICING YOUR SNOW THROWER
WARNING: Disconnect the spark plug wire
and ground it against the engine before
performing any repairs or maintenance.
Shave Plate And Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
Refer to Figure 6.
Engine
Refer to the separate engine manual packed with your
unit for all engine maintenance procedures.
To remove the skid shoes, remove the six carriage
bolts, belleville washers and hex nuts (three on each
side) which attach them to the snow thrower.
Reassemble the new skid shoes making sure that the
bolts and washers are reinstalled correctly. Also, make
certain the skid shoes are adjusted so the flat surface is
sitting level on the ground. The skid shoes can be
rotated on this machine 180° so both flat surfaces of the
skid shoe can be utilized for wear.
Augers/Shear Bolts
The augers are secured to the auger shaft with two
shear bolts and hex lock nuts. Refer to Figure 14. If you
hit a foreign object or ice jam, the snow thrower is
designed so that the bolts may shear.
If the augers will not turn, check to see if the bolts have
sheared. Two replacement shear bolts and hex lock
nuts have been provided with the snow thrower. For
future use, order kit number OEM-710-0890 which
contains four replacement shear bolts and
To remove the shave plate, remove the carriage bolts,
belleville washers and hex nuts which attach it to the
snow thrower housing. Reassemble the new shave
plate, making sure the heads of the carriage bolts are to
the inside of the housing. Tighten securely.
accompanying hex lock nuts.
IMPORTANT: NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components as a result of doing so will NOT be
covered by your snow throwers warranty.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Belt Removal And Replacement
Wheel
Drive
Pulley
WARNING: Disconnect the spark plug wire
and ground it against the engine before
performing any repairs or maintenance.
Auger
Drive
Pulley
Wheel
Drive
Belt
Auger Belts
•
Remove the plastic belt cover at the front of the
engine by removing the two self-tapping screws.
See Figure 15.
Idler
Pulley
Idler
Pulley
•
•
Drain the gasoline from the snow thrower, or place
a piece of plastic film under the gas cap.
Tip the snow thrower up and forward so that it rests
on its auger housing.
Auger
Drive
Belts
Frame
Engine
Self-Tapping
Screws
Figure 16
NOTE: If you placed plastic film under the gas cap, be
certain to remove it before operating the snow thrower.
Drive Belt
•
•
•
•
Follow the first four steps of the instructions for
servicing the auger belts.
Belt Cover
Pull the idler pulley up, and lift the belt off the wheel
drive pulley and friction wheel disc. See Figure 17.
Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 18.
Slip the belt between the friction wheel and drive
disc. See Figure 18. Remove and replace the belt.
Reassemble following the instructions in reverse
order.
Auger Housing
Figure 15
•
•
•
•
Remove the six self-tapping screws from the frame
cover underneath the snow thrower.
Roll the front and rear auger belts off the auger
drive pulley. See Figure 16.
Unhook the idler spring from the hex bolt on the
auger housing. See Figure 17.
Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 18.
NOTE: The support bracket must rest on the stop bolt
after the new belt has been assembled. See Figure 18.
NOTE: It may be necessary to loosen the six nuts that
connect the frame to the auger housing to aid in belt
removal.
Support
Bracket
•
Lift the rear auger belt from the auger pulley, and
slip the belt between the support bracket and the
auger pulley. See Figure 17. Repeat this step for
the front auger belt.
Rear
Auger
Frame
Belt
Front
Auger
Belt
•
Replace both auger drive belts by following
instructions in reverse order.
Auger
Pulley
Support
Bracket
Spring
Idler
Spring
Auger
Housing
Figure 17
14
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Reassemble the new friction wheel rubber to the
friction wheel plates and hub, tightening the six
screws in rotation and with equal force.
Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble in reverse
order.
Friction Wheel
Drive Plate
Drive Belt
Stop Bolt
NOTE: If you placed plastic film under the gas cap, be
certain to remove it.
Hex Bolt
Washer
Support Bracket
Track
Figure 18
Servicing Friction Wheel Rubber
The rubber on the friction wheel is subject to wear and
should be checked after 25 hours of operation, and
periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.
•
•
•
•
Drain the gasoline from the snow thrower, or place
a piece of plastic under the gas cap.
Tip the snow thrower up and forward, so that it rests
on the housing.
Remove the six self-tapping screws from the frame
cover underneath the snow thrower.
Using a 7/8" wrench to hold the shaft, loosen, but
do not completely remove, the hex bolt and washer
on the left end of the shaft. See Figure 19 and
Figure 20.
Figure 20
Shift Rod
Assembly
•
Lightly tap the hex bolt to dislodge the ball bearing
from the right side of frame before removing the hex
bolt and washer from the left end of the shaft.
Move the shaft to the right and slide the friction
wheel assembly from the shaft.
Remove the six screws from the friction wheel
assembly (three from each side). Remove the
friction wheel rubber from between the friction
wheel plates. See Figure 18
Sprocket
Spacer
Pin
Friction Wheel
Assembly
•
•
Support
Bracket
Screws
Shaft
Friction Wheel Rubber
Figure 21
Hub
Off Season Storage
Screws
WARNING: Never store engine with fuel in tank
indoors or in enclosed, poorly ventilated areas where
fuel fumes may reach an open flame, spark or pilot light
as on a furnace, water heater, clothes dryer, or other
gas appliance.
Friction Wheel Plates
Figure 19
•
•
Clean snow thrower thoroughly.
Lubricate as instructed above with light oil.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Follow “Storage” instructions in the Engine Manual.
Store in a clean, dry area. Block the snow thrower
up so it is not resting on the rubber auger blades.
NOTE: When storing any type of power equipment in
an poorly ventilated or metal storage shed, care should
be taken to rustproof the equipment, especially springs,
cables and all moving parts.
SECTION 9: TROUBLE SHOOTING
Problem
Cause
Remedy
Engine fails to start
1. Fuel tank empty, or stale fuel.
2. Blocked fuel line.
1. Fill tank with fresh gasoline.
2. Clean the fuel line.
3. Choke not in ON position
4. Faulty spark plug.
3. Move switch to ON position
4. Clean, adjust gap or replace.
5. Safety key not in ignition switch on engine.
6. Spark plug wire disconnected.
7. Primer button not being used properly.
8. Fuel shut-off valve closed.
5. Insert the key fully into the switch.
6. Connect spark plug wire.
7. Refer to the engine manual.
8. Open fuel shut-off valve.
Engine runs erratic
Loss of power
1. Unit running on CHOKE.
2. Blocked fuel line or stale fuel.
1. Move choke lever to OFF position.
2. Clean fuel line; fill tank with clean, fresh
gasoline.
3. Drain fuel tank and carburetor. Refill with
fresh fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
4. Refer to the engine manual.
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
1. Connect and tighten spark plug wire.
2. Remove ice and snow from gas cap. Be
certain vent hole is clear.
3. Exhaust port plugged.
3. Refer to the engine manual.
Engine overheats
Excessive vibration
1. Carburetor not adjusted properly.
1. Refer to the engine manual or have the
carburetor adjusted by an authorized
engine service dealer.
1. Loose parts or damaged auger.
1. Stop engine immediately and disconnect
spark plug wire. Tighten all bolts and nuts. If
vibration continues, have unit serviced by
an authorized service dealer.
Unit fails
to propel itself
1. Traction control cable in need of adjustment.
2. Drive belt loose or damaged.
1. Adjust traction control cable. Refer to page.
2. Replace drive belt. Refer to page 13.
Unit fails
to discharge snow
1. Discharge chute clogged.
1. Stop engine immediately and disconnect
spark plug wire. Clean discharge chute and
inside of auger housing.
2. Foreign object lodged in auger.
2. Stop engine immediately and disconnect
spark plug wire. Remove object from auger.
3. Refer to page 6 for adjustment instructions.
4. Refer to page 13.
3. Auger control cable in need of adjustment.
4. Auger belt loose or damaged.
5. Shear bolt(s) sheared
5. Replace Shear bolt(s)
Electric chute fails to
turn
1. Loose electrical connections.
1. Make sure all connections are tight and fully
installed.
2. Blown Fuse.
2. Replace with #5A fuse. The fuse is under
handle panel near switch connector.
Electric chute turns in 1. The switch connector is installed backwards
opposite direction of
the switch
1. Unplug the switch connector under the
handle panel. Turn connector 180° and
reconnect.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10:
Models 724 STE / 926 STE
4
17
11
9
16
13
8
15
10
1
14
5
18
6
3
7
12
3
2
Ref.
No.
Part No.
Part Description
618-0123
618-0418
RH Housing
1.
2.
3.
4.
LH Housing w/Fitting
Self Tapping Screw, 1/4-20 x .75
710-0642
711-0908A
711-0909A
Spiral Axle, 24” (724 STE)
Spiral Axle, 26” (926 STE)
714-0161
715-0143
717-0528
717-0526
718-0186
721-0325
721-0327
736-0351
736-0369
736-0445
741-0662
741-0663
Hi-Pro Key, 3/16 x 5/8
Spring Spiral Pin, .25 x 1.25
Worm Gear, 20-tooth
Worm Shaft
5.
6.
7.
8.
Thrust Collar
9.
Grease Plug
10.
11.
12.
13.
14.
15.
16.
17.
Grease Seal
Flat Washer, .76 x 1.5 x .030
Flat Washer, .508 x 1.0 x .020
Flat Washer, .76 x 1.5 x .060
Flange Bearing, .75 x 1.0 x .59
Flange Bearing, .503 ID x .75 OD
618-0414A
618-0415A
Gear Assy Complete, 24” (724 STE)
Gear Assy Complete, 26” (926 STE)
737-3000
737-0168
Grease Fitting, 3/16” Drive
18.
—
Grease (Two Ounces)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
68
27
57
58
72
70
72
73
57
58
55
53
27
71
69
82
65
27
80
68
92
74
63
67
59
69
27
56
64
54
58
66
81
76
79
62
60
31
45
77
78
58
66
11
15
75
9
61
29
45
51
5
40
46
5
37
47
5
8
2
14
13
17
24
5
20
22
10
14
21
84
3
11
50
9
18
40
26
85
16
1
4
41
12
10
25
31
19
86
87
43
9
15
11
42
27
35
52
7
83
14
39
35
36
90
89
9
10
14
48
38
10
6
91
49
For
reference
only
88
11
7
23
44
For
reference
only
44
32
30
28
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
Ref.
No.
Ref.
No.
Part No.
782-0599
Part Description
Motor Bracket‡
Part No.
Part Description
684-0008A
710-0262
710-0449
710-0788
710-0837
710-0890A
710-3008
711-0677
712-0429
712-3010
714-0104
720-0284
Shift Arm Assembly
Carriage Bolt 5/16-18 x 1.5”
Carriage Bolt 5/16-18 x 2.25”
TT Screw 1/4-20 x 1”
C-Sunk Screw #10-16x .625Ӡ
Shear Bolt 5/16-18 x 1.5”
Hex Screw 5/16-18 x .75”
Ferrule
49.
50.
51.
52.
1.
2.
784-5594
784-5604
Cable Bracket
Handle: Chute Tilt
3.
629-0936
629-0938A
Harness Assembly: Upper‡
Harness Assembly: Light†
4.
5.
684-0036
684-0037A
710-1003
712-0271
712-0693
716-0398
720-0232
725-1672
725-1755
725-1756
725-1759
726-0152
Handle Assembly RH
Handle Assembly LH
Special Hex Screw
Hex Sems Nut: 1/4-20
Hex Nut‡
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
6.
7.
8.
Hex Lock Nut 5/16-18
Hex Nut 5/16-18
9.
10.
11.
12.
13.
Lock Ring: Toggle Switch‡
Shift Knob
Cotter Pin
Handle Knob
Lamp Housing
720-0274
725-1757
Grip†
Heated Grip ‡
Toggle Switch: Double Thr.‡
Toggle Switch: Single Thr.‡
Halogen Lamp: 50W, 12V
Mounting Clamp‡
736-0242
736-0275
736-0451
747-0620A
747-0621
749-0951
749-0952A
749-0953A
750-0963
618-0419
629-0937
710-0262
710-0451
710-0599
710-0602
710-0805
710-0817
710-0896
710-3008
712-3027
724-0249
725-0157
731-0851A
731-1300A
731-1313C
731-1320
731-2279
736-0159
736-0242
736-0506
746-0896
746-0901
750-1232
Belleville Washer
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
Flat Washer
Saddle Washer
Shift Rod: Upper
731-2276
731-2274
Handle Pane‡
Handle Panel†
Shift Rod: Lower
736-0226
747-1136
714-0507
747-0877
784-5680
784-5679
748-0362
748-0363
732-0145
710-0459A
784-5619A
712-0116
732-0193
736-0105
784-5682
784-5681
711-0653
705-5204A
720-0201A
726-0100
747-0697
735-0234
736-0185
784-5647
741-0475
710-3015
684-0102
Flat Washer†
66.
67.
68.
69.
70.
71.
72.
73.
74.
75.
76.
77.
78.
79.
80.
81.
82.
83.
84.
85.
86.
87.
88.
89.
90.
91.
92.
Lower Handle
Headlight Retainer
Cotter Pin: 3/32 x .75
Cam Rod
Upper Handle: L Style RH
Upper Handle: L Style LH
Connector: Shift Rod
Gear Assembly: Ring ‡
Electric Harness: Lower ‡
Carriage Bolt: 5/16-18 x 1.5”
Carriage Bolt: 5.16-18 x .750”
TT Screw: 1/4-20 x 0.5”
TT Screw: 5/16-18 x 1” ‡
Hex Screw: 5/16-18 x 1.5”
TT Screw: 5/16-18 x 1.25” ‡
Hex Screw AB:1/4-14 x 0.625”
Hex Screw: 5/16-18 x .75” ‡
Hex Flange Lock Nut
Electric Motor: Chute Crank ‡
Cable Tie
RH Handle Support Bracket
LH Handle Support Bracket
Cam Handle Lock
Handle Lock Pawl
Compression Spring: .36 x 1.0
Hex Cap Screw: 3/8-24 x 1.5
Shift Handle
Jam Nut, 3/8-24
Comp. Spring: .39 x .6 x .88
Bell Washer
RH Handle Support Bracket
LH Handle Support Bracket
Clevis Pin
Chute Crank Assembly †
Knob †
Chute Flange Keeper
Lower Chute
Push Cap †
Cable Guide: Chute Tilt
Upper Chute
Eyebolt †
Rubber Grommet †
Flat Washer†
Motor Cover: Chute Rotation ‡
5/16 Washer
Chute Crank Brkt.†
Plastic Bushing†
Belleville Washer ‡
Special Washer
Hex Head Cap Screw 1/4-20†
Handle Panel
Control Cable
Control Cable
Spacer‡
† 724 STE
‡ 924 STE
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
2
1
3
4
5
11
10
9
15
18
6
14
12
7
8
13
16
22
23
21
27
10
34
28
25
23
9
13
38
26
30
35
19
22
18
32
31
33
16
41
37
36
17
40
39
24
40
39
29
42
20
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
Ref.
No.
Ref.
No.
Part No.
736-0463
Part Description
Flat Washer
Part No.
712-0116
Part Description
Lock Jam Nut 3/8-24
Flat Idler
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
1.
2.
784-0399
710-0703
710-0604
736-0169
712-0798
741-0245
784-5038B
736-0242
712-3010
Bearing Housing w/Fitting
Carriage Screw 1/4-20 x .75
Hex Screw 5/16-18
Lock Washer 3/8
Hex Nut 3/8-16
756-0178
784-5632A
710-0459A
738-0281
736-0167
732-0611
712-3068
710-0276
736-0119
05931A
Auger Idler Arm
3.
Hex Cap Screw 3/8-24 x 1.50
Shoulder Screw
4.
5.
Flat Washer
6.
Hex Flange Bearing
Skid Shoe
Extension Spring
Hex Nut 5/16-18
7.
8.
Bell Washer
Carriage Bolt, 5/16-18 x 1.00
Lock Washer 5/16
Housing
9.
Hex Nut 5/16-18
10.
11.
12.
13.
14.
15.
784-5581A
784-5579A
Shave Plate (724 STE)
Shave Plate (926 STE)
741-0309
710-0451
705-5226
Ball Bearing
710-0260
684-0065
715-0114
Carriage Bolt 5/16-18 x .62
Impeller Assembly
Pin
34.
35.
36.
37.
Carriage Bolt, 5/16-18 x .75
Chute Reinforcement
684-0039C
684-0040C
24” Housing Assy (724 STE)
26” Housing Assy (926 STE)
618-0414A
618-0415A
24” Gear Assy (724 STE)
26” Gear Assy (926 STE)
712-3010
712-0429
736-0242
736-0231
737-3000
731-1379B
712-0324
Hex Nut 5/16-18
16.
17.
18.
19.
20.
21.
22.
605-5188A
605-5192A
24” Spiral RH (724 STE)
26” Spiral RH (926 STE)
38.
Lock Nut 5/16-18
Belleville Washer
736-0188
Flat Washer
39.
40.
41.
Flat Wshr, .344ID x 1.125 OD
Grease Fitting, 3/16” Drive
Chute Adapter
741-0493A
Flange Bushing
605-5189A
605-5193A
24” Spiral LH (724 STE)
26” Spiral LH (926 STE)
710-0890A
Shear Bolt 5/16-18 x 1.5
Hex Lock Nut 1/4-20
42.
NOTE: For painted parts, please refer to the list
of color codes below. Please add the applicable
color code, wherever needed, to the part number
to order a replacement part. For instance, if a
part, numbered 700-xxxx, is painted Cub Yellow,
the part number to order would be 700-xxxx-0716.
Cub Yellow: 0716
Cub Beige: 0499
Powder Black: 0637
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 926 STE
28
29
30
1
27
1
2
26
3
4
8
9
4
7
10
11
12
16
19
15
6
5
16
16
19
16
21
22
23
13
14
17
18
25
20
IMPORTANT: For a proper working machine, use Factory
Approved Parts.
V-BELTS are specially designed to engage and disengage
safely. A substitute (non OEM) V-Belt can be dangerous by
not disengaging completely
24
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 926 STE
Ref.
No.
Part No.
710-1652
Part Description
Hex Washer Screw 1/4-20 x .625
Belt Cover
1.
731-1324
732-0710
710-0627
710-3005
05896A
2.
Extension Spring
Hex Screw 5/16-24 x .75
Hex Cap Screw 3/8-16 x 1.25
Drive Clutch Idler Bracket
Shoulder Spacer
Pulley Half
3.
4.
5.
6.
748-0234
756-0987
754-0346
756-0986
736-0270
710-0230
756-0313
710-1245
712-0181
756-0569
736-0242
736-0505
754-0430A
756-0967
736-0247
736-0331
710-0696
748-0360
710-0654A
629-0071
OEM-390-987
712-0324
736-0173
732-0705
7.
8.
V-Belt
9.
Pulley Half
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
Bell Washer
Hex Cap Screw 1/4-28 x .50
Flat Idler
Lock Hex Cap Screw 5/16-24
Lock Jam Nut 3/8-16
Pulley Half
Bell Washer
Flat Washer
Belt
Auger Pulley
Flat Washer 3/8 x 1.25 OD
Bell Washer
Hex Cap Screw 3/8-24
Adapter Pulley
Hex Screw 3/8-16 x 1.0
Extension Cord
Electric Start Kit
Lock Nut, 1/4-20
Flat Washer, .28 x .74 x .063
Cable Guide
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 724 STE
1
29
30
2
28
31
32
11
3
20
8
27
22
3
23
9
15
2
26
24
21
24
14
12
16
1
5
6
13
17
18
4
19
25
IMPORTANT: For a proper working machine, use Factory
Approved Parts.
V-BELTS are specially designed to engage and disengage
safely. A substitute (non OEM) V-Belt can be dangerous by
not disengaging completely
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 724 STE
Ref.
No.
Part No.
05896A
Part Description
Drive Clutch Idler Bracket
Hex Cap Screw 1/4-20
Hex Cap Screw 5/16-24
Hex Screw 3/8-16 x 1.0
Hex Cap Screw 3/8-24
Lock Hex Cap Screw 6/16-24
Hex Washer Screw 1/4-20 x .625
Hex Cap Screw 3/8-16 x 1.25
Lock Jam Nut 3/8-16
Belt Cover
1.
710-0230
710-0627
710-0654A
710-0696
710-1245
710-1652
710-3005
712-0181
731-1324
732-0339
736-0159
736-0242
736-0247
736-0270
736-0331
736-0505
736-0507
748-0360
750-1053
754-0430A
754-0456
756-0313
756-0569
756-0967
756-0984
756-0985
OEM-390-987
712-0324
736-0173
732-0705
629-0071
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
Extension Spring
Washer 5/16
Bell Washer
Flat Washer
Bell Washer
Bell Washer
Flat Washer
Special Washer
Adapter Pulley
Spacer
Belt
V-Belt
Flat Idler
Pulley Half
Auger Pulley
Pulley Half
Pulley Half
Electric Start Kit
Lock Nut, 1/4-20
Flat Washer, .28 x .74 x .063
Cable Guide
Extension Cord
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
22
34
23
24
32
2
30
25
31
19
29
26
21
32
27
20
19
30
18
17
26
19
16
27
2
25
24
23
22
20
10
2
18
19
14
21
36
11
28
15
3
30
13
12
4
1
9
7
6
5
39
38
32
2
37
40
32
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
Ref.
No.
Ref.
No.
Part No.
Part Description
Part No.
Part Description
Tap Screw, 1/4-20 x .75
784-5648
710-1652
748-0190
732-0264
712-0711
736-0105
684-0021
746-0898
656-0012A
784-5689A
713-0413
746-0897
750-0997
711-1042
684-0042C
736-0160
714-0474
741-0563
736-0242
710-0538
Frame Cover
710-0875
736-0270
736-0176
741-1111
710-0643
748-0234
710-0604
684-0031
738-0924
756-0625
784-5688
710-0599
784-5590
684-0014B
784-5687A
710-0809
618-0063
718-0301A
735-0243
784-5617A
1.
2.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
Tap Screw, 1/4-20 x .625
Spacer, .508 ID x .75 OD x .68
Ext. Spring
Bell Washer, .265 x .75 x .062
Flat Washer, 1/4 ID x .93 OD x .12
Hex Flange Bearing
Hex Cap Screw, 5/16-18 x 1
Shoulder Spacer
3.
4.
Jam Nut, 3/8-24
5.
Bell Washer, .401 x .87 x .063
Friction Wheel Support Bracket Assy
Drive Cable, 39.88”
6.
Tap Screw, 5/16-18 x .625
Frame Assembly
7.
8.
Friction Disc
Spacer
9.
Front Support Guide Bracket
Ten-Tooth Sprocket
Cable Roller
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
Drive Cable Guide Bracket
Tap Screw, 1/4-20 x .5
Shift Frame Bracket
Shift Rod Assembly
Auger Cable Guide Bracket
Tap Screw, 1/4-20 x 1.25
Friction Wheel Bearing
Friction Wheel Hub
Auger Cable, 44.75”
Spacer, .675 ID x 1 OD x .23
Hex Track Shaft
Friction Wheel Assembly
Flat Washer, .536 ID x .93 OD x .05
Cotter Pin
Ball Bearing
Bell Washer, .34 ID x .872 OD
Hex Cap Screw, 5/16-18 x .625
Friction Wheel Rubber
Friction Plate
NOTE: For painted parts, please refer to the list
of color codes below. Please add the applicable
color code, wherever needed, to the part number
to order a replacement part. For instance, if a
part, numbered 700-xxxx, is painted Cub Yellow,
the part number to order would be 700-xxxx-0716.
Cub Yellow: 0716
Cub Beige: 0499
Powder Black: 0637
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
44
42
43
45
41
54
50
51
46
47
1
51
2
53
54
55
52
48
3
46
5
49
9
6
4
11
56
30
10
38
37
12
19
36
8
35
39
20
32
7
16
40
30
33
29
23
13
37
26
15
56
27
22
17
34
33
28
31
20
32
25
14
19
18
21
24
22
16
13
26
21
18
15
14
17
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 724 STE / 926 STE
Ref.
No.
Ref.
No.
Part No.
720-0223
Part Description
Part No.
618-0169
Part Description
Grip
Track/Steering Shaft Assy
Track Hub Assy w/Fitting
Chain
1.
2.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
710-0604
784-5642
710-0157
736-0242
684-0038
710-0459A
712-0214
748-0353A
750-0547
784-5609
684-0009
712-0346
731-1292
736-0272
731-1538A
631-0032
750-0995
738-0140
736-0406
750-0909
712-0429
618-0044
684-0024
710-1231
784-5639
711-0911
713-0233
Tap Screw, 5/16-18 x .625
Track Lockout Plate
Hex Cap Screw, 5/16-24 x .75
Bell Washer, .34 ID x .872 OD
Track Lock Handle Assembly
Hex Cap Screw, 3/8-24 x 1.5
Hex Nut, 3/8-24
684-0154
713-0437
741-0339
736-0287
611-0053
750-0904
618-0043
750-0903
732-0209
710-0602
719-0295A
746-0948
746-0950
712-0127
710-1233
716-0114
618-0046
717-1211
716-0115
713-0414
711-0912
736-0502
736-0336
715-0120
717-1209
717-1210
737-3000
3.
Flange Bearing
4.
Flat Washer, .793 x 1.24 x .06
Axle Assembly
5.
6.
Spacer, .514 x .630 x 1.59
RH Dogg Assembly
Spacer, .514 x .630 x 2.44
Ext. Spring
7.
8.
Lift Shaft Drive
9.
Spacer, .628 ID x .875 OD x .5
Steering Cable Bracket
Track Pivot Rod Assembly
Jam Nut, 1/2-20
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Tap Screw, 5/16-18 x 1
Track Housing
Steering Cable
Snow Track
Steering Trigger
Flat Washer, .5 x 1 x .06
Track Drive Wheel
Flange Nut
Screw, #10-24 x 1.375
Retaining Ring
Track Idler Wheel
Spacer, .51 ID x .75 OD x 1.67
Screw, .435 x .178-5/16 x .56
Flat Washer, .442 x 1.38 x .06
Spacer, .51 ID x 1 OD x 1.34
Hex Nut, 5/16-18
Carrier Assembly
Ring Gear
Retaining Ring
13-Tooth Sprocket
Track Steering Drive Shaft
Flat Washer, .58 x 1.06 x .02
Flat Washer, 5/8 x 1 x .03
Spiral Pin, 3/16 x 1
12-Tooth Gear
LH Dogg Assembly
Idler Axle Assembly
Eye Bolt, 5/16-18 x 3
Track Side Plate
Actuator Shaft
18-Tooth Gear
Chain
Grease Fitting, 3/16” Drive
NOTE: For painted parts, please refer to the list
of color codes below. Please add the applicable
color code, wherever needed, to the part number
to order a replacement part. For instance, if a
part, numbered 700-xxxx, is painted Cub Yellow,
the part number to order would be 700-xxxx-0716.
Cub Yellow: 0716
Cub Beige: 0499
Powder Black: 0637
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
TWO-YEAR RESIDENTIAL
ONE-YEAR COMMERCIAL
Proper maintenance of your Cub Cadet equipment is the owner’s responsibility. Follow the instructions in your
operator’s manual for correct lubricants and maintenance schedule. Your Cub Cadet dealer carries a
complete line of quality lubricants and filters for your equipment’s engine, transmission, chassis and
attachments.
Riding mowers, lawn tractors, garden tractors, Cub Cadet
attachments and home maintenance products
This limited warranty for residential users, covers any defect in materials or workmanship in your Cub Cadet
equipment for two years from the date of purchase for the first user purchaser. We will replace or repair any
part or parts without charge through your authorized Cub Cadet dealer.
Batteries have a one-year prorated limited warranty with 100% replacement during the first three months.
V-belts for either the traction drive or any attachments are covered for one year only.
Cub Cadet equipment used commercially is warranted for one year only.
(Commercial use is defined as either having hired operators or used for income producing purposes.)
Items not covered
The warranty does not cover routine maintenance items such as lubricants, filters (oil, fuel, air and hydraulic),
cleaning, tune-ups, brake and/or clutch inspection, adjustments made as part of normal maintenance, blade
sharpening, set-up, abuse, accidents and normal wear. It does not cover incidental costs such as transporting
your equipment to and from the dealer, telephone charges or renting a product temporarily to replace a
warranted product.
There is no other express warranty.
How to obtain service
Contact your authorized Cub Cadet servicing dealer who sold you your Cub Cadet equipment. If this dealer is
not available, see the Consumer Yellow Pages under “lawn mowers” for the name of a dealer near you.
If you need further assistance in finding an authorized Cub Cadet servicing dealer, contact:
Cub Cadet Corporation
Post Office Box 368023
Cleveland, Ohio 44136
How does state law apply?
This limited warranty gives you specific legal rights, and you may also have other rights which vary from state
to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
|