Operator’s Manual
SERIES 5000
TRACTOR
MODEL 5252
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved
forest-covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark
arrester meeting applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective
working order by the operator. In the State of California the above is required by law (Section 4442 of the California Public
Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester for the
muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box
361131 Cleveland, Ohio 44136-0019.
CUB CADET LLC P.O. BOX 361131 CLEVELAND, OHIO 44136-0019 [www.cubcadet.com]
PRINTED IN U.S.A.
FORM NO. 769-00867I
(7/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
RECORDING MODEL AND SERIAL NUMBER INFORMATION
Product identification plates are provided for major components of your tractor. The numbers on these
plates are important if your tractor should require dealer service, or if you need additional information
on your tractor. Prior to using your tractor for the first time, record the numbers from the identification
plates in the appropriate spaces provided below.
•
•
The tractor model plate is located on the right frame rail behind the right front tire.
The engine information plate is located on the side of the blower housing at the front of the
engine.
•
•
The transmission serial plate is located on the rear of the transmission, below the PTO shaft.
The ROPS information plate is located on a vertical leg of the ROPS.
Tractor Model Plate:
Model Number
Mfg. Date (Serial No.)
Engine Information:
Model No.
Displacement
Serial Number
Spec. No.
Serial No.
Transmission Serial Plate:
ROPS Information Plate:
ROPS Serial No.
TRANSMISSION SERIAL PLATE
TRACTOR MODEL PLATE
XXXXXXXXXXX
Model Number
XXXXXXXXXX
Mfg. Date
CUB CADET LLC
P. O. BOX 361131
www.cubcadet.com CLEVELAND, OH 44136
DEALER LOCATOR PHONE NUMBER: 877-282-8684
ROPS INFORMATION PLATE
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFE OPERATION PRACTICES
WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF
NOT FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF
YOURSELF AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL
BEFORE ATTEMPTING TO OPERATE YOUR UNIT. FAILURE TO COMPLY WITH THESE
INSTRUCTIONS MAY RESULT IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL,
HEED ITS WARNING.
WARNING: The engine exhaust, some of its constituents, and certain vehicle components
contain or emit chemicals known to the State of California to cause cancer, birth defects or other
reproductive harm.
DANGER: Your tractor was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. To help prevent accidents, read and take the following precautions before
operating this tractor. Failure to observe the following safety instructions could result in serious
injury or death.
•
Be aware of the mower and attachment
discharge direction and do not point it at
anyone. Do not operate the mower without
either the entire grass catcher or the chute
guard in place.
1. GENERAL OPERATION
•
Read, understand, and follow all instructions in
the operator’s manual and on the machine
before starting. Keep this manual in a safe
place for future and regular reference.
•
•
Slow down before turning. Operate the
machine smoothly. Avoid erratic operation and
excessive speed.
•
Only allow responsible individuals familiar with
the instructions to operate the machine. All
operators should evaluate their ability to oper-
ate the tractor safely enough to protect
themselves and others from serious injury.
Know controls and how to stop the machine
quickly.
Never leave a running machine unattended.
Always turn off the blades, place the
transmission in neutral, set the parking brake,
stop the engine and remove key before
dismounting.
•
•
Do not put hands or feet under the cutting deck
or near rotating parts.
•
•
Turn off blades when not mowing.
Stop the engine and wait until the blades come
to a complete stop before (a) removing the
grass catcher or unclogging chute, or (b)
making any repairs, adjusting or removing any
grass or debris.
Clear the area of objects such as rocks, toys,
wire, etc. which could be picked up and thrown
by the blades. A small object may have been
overlooked and could be accidentally thrown by
the mower in any direction and cause injury to
you or a bystander. To help avoid a thrown
objects injury, keep children, animals,
bystanders and helpers at least 75 feet from
the mower while it is in operation. Always wear
safety glasses with side shields or safety
goggles during operation or while performing
an adjustment or repair, to protect eyes from
foreign objects. Stop the blades when crossing
gravel drives, walks or roads.
•
•
Mow only in daylight or good artificial light.
Do not operate the machine while under the
influence of alcohol or drugs.
•
•
•
Use extra care when loading or unloading the
machine into a trailer or truck because the unit
could tip over causing serious personal injury.
Never make a cutting height adjustment while
the engine is running if the operator must
dismount to do so.
•
Be sure the area is clear of other people before
mowing. Stop machine if anyone enters the
area.
Wear sturdy, rough-soled work shoes and
close-fitting slacks and shirts. Do not wear
loose fitting clothes or jewelry. They can be
caught in moving parts. Never operate a unit in
bare feet, sandals or sneakers.
•
•
Never carry passengers.
Use extreme caution when shifting into reverse
and backing up. Always look down and behind
before and while backing.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Disengage all attachment clutches, thoroughly
depress the brake pedal and shift into neutral
before attempting to start the engine.
•
•
Check overhead clearance carefully before
driving under power lines, wires, bridges or low
hanging tree branches, before entering or
leaving buildings, or in any other situation
where the operator and/or roll bar may be
struck, which could result in serious injury.
Your mower is designed to cut normal
residential grass of a height no more than 10”.
Do not attempt to mow through unusually tall,
dry grass (e.g. pasture) or piles of dry leaves.
Debris may build up on the mower deck or
contact the engine exhaust presenting a
potential fire hazard.
If the tractor becomes stuck, use reverse to
free the tractor to prevent tractor upset.
2. SLOPE OPERATION
•
•
Use only accessories approved for this
machine by Cub Cadet. Read, understand and
follow all instructions provided with the
approved accessory.
Slopes are a major factor related to loss of control
and tip-over accidents which can result in severe
injury or death. All slopes require extra caution. If
you cannot back up the slope or if you feel uneasy
on it, do not operate this unit on that area or serious
injury could result.
Use the roll bar and seat belt for safe operation.
Overturning the tractor without a roll bar, or with
a roll bar and the seat belt unfastened, can
result in death or injury.
Do not operate on inclines with a slope in excess of
15 degrees (a rise of approximately 2-1/2 feet every
10 feet). The tractor could overturn and cause
serious injury
•
•
Always use the seat belt, except when the roll
bar is in the folded position, or if the roll bar has
been removed.
DO:
Use the handholds and running boards when
getting on and off the tractor to help prevent
accidental falls. Keep the running boards clear
of mud and debris.
•
•
•
Operate up and down slopes, not across.
Remove obstacles such as rocks, limbs, etc.
Watch for holes, ruts or bumps. Uneven terrain
could overturn the machine. Tall grass can hide
such obstacles.
•
•
Keep all safety decals clean and readable.
Replace any missing, illegible, or damaged
safety decals.
•
Place the transmission in the low range. when
climbing or descending slopes. Always keep
machine in gear when going down slopes to
take advantage of engine braking action.
Always sit in the tractor seat when starting the
engine or operating controls. Do not start the
engine or operate controls while standing
beside the tractor.
•
•
Follow the manufacturers recommendations for
counterweights to improve stability.
•
•
•
Never tamper with safety devices. Check their
proper operation regularly. Contact your Cub
Cadet dealer if safety devices malfunction.
Keep all movement on the slopes slow and
gradual. Do not make sudden changes in
speed or direction. Rapid engagement or
braking could cause the front of the machine to
lift and rapidly flip over backwards which could
cause serious injury.
Avoid accidental contact with control pedals
while the engine is running, as this can cause
unexpected movement of the tractor.
Pull only from a drawbar or the lower hitch links
in the down position. Make certain the drawbar
pin is locked in place. Pulling from the rear axle
of the tractor or any point above the axle could
cause the tractor to overturn.
•
Avoid starting or stopping on a slope. If tires
lose traction, disengage the PTO and proceed
slowly straight down the slope.
•
Maintain the weight balance of the tractor.
Install front end weights to counterbalance
heavy implements attached to the three point
hitch. Do not operate the tractor with a light
front end.
DO NOT:
•
Do not turn on slopes unless necessary; then,
turn slowly and gradually downhill, if possible.
•
Do not mow near drop-offs, ditches or
embankments. The mower could suddenly turn
over if a wheel goes over the edge of a cliff or
ditch, or if an edge caves in.
•
•
Do not leave equipment in the raised position.
Watch for traffic when operating near or
crossing roadways. If local laws permit road
travel, use the flashing hazard lights and SMV
signs when traveling on public roadways.
•
•
Do not mow on wet grass. Reduced traction
could cause sliding.
Do not try to stabilize the machine by putting
your foot on the ground.
•
Make certain all tractor lights are illuminated
when operating at night.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Never attempt to straighten or reweld any part
of the main frame or retaining brackets that
have been damaged. Doing so may weaken
the structure and endanger your safety.
3. CHILDREN
•
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are
often attracted to the machine. Never assume
children will remain where you last saw them.
Never secure any parts on the main frame or
attach the safety frame with anything other than
the special fasteners specified.
•
•
Keep children out of the mowing area and in
watchful care of an adult other than the
operator.
•
•
Never attach ropes, chains, or cables to the
ROPS for pulling purposes.
To avoid back-over accidents, always disen-
gage the cutting blades before shifting in
reverse. The "PTO Reverse Override Switch"
should not be used when children or others
are around.
Although the ROPS provides you the maximum
protection possible, never take unnecessary risks.
6. SERVICE
•
•
•
•
Be alert and turn machine off if children enter
the area.
Use extreme care in handling gasoline and
other fuels. They are extremely flammable and
the vapors are explosive. Use only an approved
container.
Before and when backing, look behind and
down for small children.
Never carry children, even with the blades off.
They may fall off and be seriously injured or
interfere with safe machine operation.
a. Use only an approved container.
b. Never remove fuel cap or add fuel with the
engine running. Allow the engine to cool at
least two minutes before refueling.
c. Replace the fuel cap securely and wipe off
any spilled fuel before starting the engine as
it may cause a fire or explosion.
•
Never allow children under 14 years old to
operate the machine. Children 14 years and
over should only operate machine under close
parental supervision and proper instruction.
•
•
Use extra care when approaching blind
corners, shrubs, trees or other objects that may
obscure your vision of a child or other hazard.
d. Extinguish all cigarettes, cigars, pipes and
other sources of ignition.
e. Never refuel the machine indoors because
fuel vapors will accumulate in the area.
f. Never store the fuel container or machine in-
side where there is an open flame or spark,
such as a gas hot water heater, space heat-
er or furnace.
Remove key when machine is unattended to
prevent unauthorized operation.
4. OPERATING THE PTO
•
When operating PTO driven equipment,
disengage the PTO, stop the engine, and wait
until the PTO stops before dismounting the
tractor and disconnecting the equipment.
•
Escaping hydraulic fluid under pressure can
penetrate the skin. If fluid is injected into the
skin, seek immediate medical attention. Do not
use your hand to check for leaks. Use a piece
of cardboard or paper.
•
•
•
Do not wear loose fitting clothing when
operating the PTO or when near rotating
equipment.
•
•
Never run a machine inside a closed area.
To reduce fire hazard, keep the tractor free of
any debris build-up. Clean up oil or fuel spillage.
To prevent injury, do not adjust, unclog, clean,
or service PTO driven equipment while the
tractor engine is running.
•
•
Before cleaning, repairing or inspecting, make
certain the blades and all moving parts have
stopped.
Make certain all PTO shields are always installed.
Check the blade fasteners at frequent intervals
for proper tightness. Also visually inspect
blades for damage (e.g., excessive wear, bent,
cracked). Replace with blades which meet
original equipment specifications.
5. SAFETY FRAME (ROPS)
Your tractor is equipped with a rollover protective
structure (ROPS) which must be maintained in a
fully functional condition. Use care when driving
through doorways or spaces with a low overhead.
•
Never modify the ROPS in any way.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
•
•
•
Prior to disposal, determine the proper method
to dispose of waste from your local
Environmental Protection Agency. Recycling
centers are established to properly dispose of
materials in an environmentally safe fashion.
Never tamper with safety devices. Check their
proper operation regularly.
After striking a foreign object, stop the engine,
and thoroughly inspect the mower for any
damage. Repair the damage before restarting
and operating the mower.
Use proper containers when draining fluids. Do
not use food or beverage containers that may
mislead someone into drinking from them.
Properly dispose of the containers immediately
following the draining of fluids.
•
Mower blades are sharp and can cut. Wrap the
blades or wear gloves, and use extra caution
when servicing blades.
DO NOT pour oil or other fluids into the ground,
down a drain or into a stream, pond, lake or
other body of water. Observe Environmental
Protection Agency regulations when disposing
of oil, fuel, coolant, brake fluid, filters, batteries,
tires and other harmful waste.
•
•
Check brake operation frequently. Adjust and
service as required.
Engine components become hot during
operation and can cause a burn. Allow to cool
down before touching.
•
We do not recommend the use of a pressure
washer or garden hose to clean your unit. They
may cause damage to electrical components;
spindles; pulleys; bearings; or the engine. The
use of water will result in shortened life and
reduce serviceability.
•
•
Do not change the engine governor settings or
overspeed the engine. Excessive engine
speeds are dangerous.
Observe proper disposal laws and regulations.
Improper disposal of fluids and materials can
harm the environment and the ecology.
WARNING: - YOUR RESPONSIBILITY: Restrict the use of this power machine to persons who
read, understand and follow the warnings and instructions in this manual and on the machine.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY LABELS
WARNING
AVOID SERIOUS
WARNING
INJURY OR DEATH
1. GO UP AND DOWN SLOPES,
NOT ACROSS.
2. AVOID SUDDEN TURNS.
3. DO NOT OPERATE UNIT WHERE
IT COULD SLIP OR TIP.
4. IF MACHINE STOPS GOING
UPHILL, STOP PTO AND BACK
DOWN HILL SLOWLY.
5. DO NOT MOW WHEN CHILDREN
OR OTHERS ARE AROUND.
To avoid personal injury, keep PTO shield in place.
Pull only from draw bar. pulling from any other point can cause rear overturn.
Disengage PTO and stop engine before servicing tractor, or implements,
or attaching or detaching implements.
FAILURE TO FOLLOW ANY OF THE INSTRUCTIONS ABOVE CAN CAUSE
SERIOUS INJURY TO THE OPERATOR, OR OTHER PERSONS.
6. DO NOT ALLOW PASSENGERS
ON THE TRACTOR AT ANY TIME.
7. LOOK DOWN AND BEHIND
BEFORE AND WHILE BACKING.
8. KEEP SAFETY DEVICES
[GUARDS, SHIELDS, AND
SWITCHES] IN PLACE AND
WORKING.
PTO WARNING LABEL
REAR PTO SHIELD
9. REMOVE OBJECTS THAT
COULD BE THROWN BY
THE BLADES.
10. KNOW LOCATION AND
FUNCTION OF ALL CONTROLS.
WARNING
BE SURE THE BLADES AND THE
ENGINE ARE STOPPED BEFORE
PLACING HANDS OR FEET NEAR
BLADES.
11.
BATTER IES CON TAIN ACID AN D EXP LOSIV E GAS.
EXPLOSION CAN R ESU LT FR OM SPAR KS, FLAM ES,
OR W R ON G CABLE CON N ECTION S . TO CON N ECT
JU M PER CABLES OR CH AR GER SEE M AN U AL FOR
COR R ECT PR OCED U R E. FAILU R E TO FOLLOW TH E
ABO V E IN S TR U CTION S CAN CAU S E S ER IO U S
PER SON AL IN JU RY OR D EATH .
12. BEFORE LEAVING OPERATOR'S
POSITION, DISENGAGE PTO,
ENGAGE BRAKE LOCK, SHUT
OFF ENGINE AND REMOVE KEY.
13. SLOW DOWN FOR TURNS,
ROUGH GROUND AND SLOPES
TO AVOID UPSET.
14. ON PUBLIC ROADS USE SMV
EMBLEM AND HAZARD LIGHTS.
READ OPERATOR'S
MANUAL
INSTRUCTION LABEL
RIGHT RUNNING BOARD
BATTERY WARNING LABEL
LOCATED UNDER HOOD
INSTRUCTION-WARNING
LEFT RUNNING BOARD
TO REDUCE THE RISK OF INJURY, DO NOT
When improperly operated this tractor can
roll over or upset. Use of the ROPS and
seat belt minimize the possibility of injury
or death if roll over or upset occurs.
OPERATE UNLESS DISCHARGE COVER OR
GRASS CATCHER IS IN ITS PROPER PLACE.
IF D AM AG ED , R EPL ACE IM M ED IATEL Y.
ROLL OVER WARNING LABEL
ON RIGHT/REAR FENDER
KEEP HANDS AND FEET AWAY FROM
HANDS/FEET SAFETY GRAPHIC
ON DEFLECTOR CHUTE
ROTATING PARTS
.
REMOVE OBJECTS THAT CAN BE
THROWN BY THE BLADE IN ANY
DIRECTION. WEAR SAFETY GLASSES.
DO NOT MOW WHEN CHILDREN OR
OTHERS ARE AOUND. NEVER CARRY
CHILDREN
.
USE EXTRA CAUTION ON SLOPES. DO
NOT MOW SLOPES GREATER THAN 15°.
MOW UP AND DOWN, NOT ACROSS
.
AVOID SUDDEN TURNS, USE LOW GEAR
.
READ OPERATOR'S MANUAL. KEEP SAFETY DEVICES WORKING.
SAFETY GRAPHIC – LOCATED ON
LEFT SIDE OF MOWER DECK
DEFLECTOR and SAFETY GRAPHIC –
LOCATED ON RIGHT SIDE OF DECK
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: CONTROLS AND FEATURES
W
X
A
B
V
C
D
F
HOURS 1/10
FUEL
RPM
0
x1000
4
U
T
E
F
E
S
R
G
H
Q
H
J
P
K
O
L
L
M
N
Figure 1
A. Steering Wheel
B. Throttle Handle
C. PTO Switch
D. Ignition Switch
E. Brake Pedal
H. Hand Holds
J. Hydraulic Lift Lever
K. Cup Holder
Q. PTO Reverse Override Switch
R. Parking Brake Lever
S. Differential Lock Pedal
T. Choke Control Knob
U. Hazzard Light Switch-If Equipped
V. Headlight Switch
L. Amber Hazzard Light
M. Seat Adjustment Lever
N. Seat Belt
O. Fuel Fill Cap
F. Reverse Pedal
G. Forward Pedal
W. ROPS (Fixed or Foldable)
X. Instrument Panel
P. Trans. Hi/Lo Shift Lever
* Steering Wheel, Seat, and ROPS Transparent for Clarity
9
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: References to LEFT and RIGHT indicate
that side of the tractor when facing forward while
seated in the drivers seat. Reference to FRONT
indicates the grille end of the tractor; to REAR, the
tow plate end.
OFF
STOP
ON
START
A. Steering Wheel
The steering wheel is centered on the dash panel,
and used to change the direction (left or right) of
the tractor while driving.
Figure 3
OFF - The engine and electrical system is turned
off.
NOTE: This tractor is equipped with hydraulic
power steering. With this feature, the cap and
spokes of the steering wheel may change position.
ON - The tractor electrical system is energized.
START- The starter motor will turn over the engine.
Release the key immediately when the
engine starts
B. Throttle Handle
E. Brake Pedal
This symbol indicates the
fast position.
Brake Pedal
Symbol
This symbol indicates the
slow position.
The throttle handle is located to the right of the
steering wheel on the dash panel. When set in a
given position, a uniform engine speed will be
maintained. Rotate the handle rearward to increase
the engine speed.
Figure 4
The brake pedal is located at the front of the right
running board above the forward and reverse
pedals. Depress to engage the tractor brakes and
neutralize the hydrostatic transmission. Fully
depress the brake pedal to activate the safety
interlock switch when starting the tractor.
C. PTO Switch
PTO
Switch
Symbol
F. Reverse Pedal
Reverse
Pedal
Figure 2
Symbol
The PTO switch is a rocker type switch located to
the right of the steering wheel on the dash panel.
Push the top of the PTO switch downward to
engage the PTO. Push the bottom of the switch
downward to disengage.
Figure 5
The reverse control pedal is located on the right
running board below the brake pedal. Press the
pedal down to move in reverse.
D. Ignition Switch
WARNING: Check behind the tractor to
be sure the area is clear of people or
obstacles. Use a slower speed to
maintain control of the tractor when
traveling in reverse.
NOTE: To prevent accidental starting and/or battery
discharge, remove the key from the ignition switch
when the tractor is not in use.
The ignition switch has three positions as follows:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
G. Forward Pedal
O. Fuel Fill Cap
The fuel fill cap is located on the left fender beside
the operator’s seat.
Forward
Pedal
Symbol
P. Transmission Hi/Lo Range Shift Lever
The Hi/Lo range shift lever is located on the left
fender. The lever has two speed range settings and
a neutral position. The lever must be shifted into
either the high or low range prior to depressing the
forward or reverse pedal to drive the tractor.
Figure 6
The forward control pedal is located on the right
running board below the brake pedal. Slowly press
down on the pedal to start moving forward. The
forward ground speed of the tractor is directly
affected by the distance the pedal is depressed.
•
•
•
Push the lever fully forward to shift into the high
range.
Pull the lever fully rearward to shift into the low
range.
Move the lever to the center position to shift
into the neutral position.
H. Hand Holds
Hand holds are built into both the left and right hand
fender covers. The handles can be used to assist in
mounting and dismounting the tractor.
WARNING: Never attempt to shift the
Hi/Lo range lever when the tractor is in
motion.
J. Hydraulic Lift Lever
The hydraulic lift lever is located on the right fender.
This lever is used to raise and lower the three point
hitch lift arms.
Q. PTO Reverse Override Switch
The PTO reverse override switch is located on the
left fender. Depress the front of the switch to
engage the override which allows the PTO to
operate while the tractor is traveling in the reverse
direction. The indicator light in the override switch
will illuminate when the switch is depressed to the
"ENGAGED" position.
IMPORTANT: Once activated, this function remains
activated until the ignition switch is turned to the
OFF position for a duration of at least 20 seconds.
•
Move the lift lever fully rearward to raise the lift
arms.
•
•
Move the lift lever forward to lower the lift arms.
Move the lift lever fully forward and to the right
ahead of the float lock bracket to lock the lift in
the float position.
K. Cup Holder
The cup holder is located on the right fender.
WARNING: Use EXTREME caution
when operating PTO driven attach-
ments while traveling in the reverse
direction.
L. Amber Hazard Lights
The hazard lights are located on each side of the
ROPS. The lights illuminate in a flashing mode
when the hazard light switch is turned on. Always
use the hazard lights when it is necessary to warn
others that the tractor is being operated in the area.
R. Parking Brake Lever
Parking
Brake
M. Seat Adjustment Lever
Symbol
The seat adjustment lever is located at the right/
front of the seat. This lever is used to adjust the
seat forward or backward.
N. Seat Belt
The seat belt, when properly adjusted and used in
conjunction with the Rollover Protective Structure
(ROPS), can greatly reduce the risk of serious
injury or death to the operator if an accidental
tractor overturn occurs.
Figure 7
The parking brake lever is located below the
steering wheel in the dash panel. With the brake
pedal fully depressed, push the parking brake lever
downward and release the brake pedal to lock the
parking brake.
WARNING: DO NOT use the seat belt if
the ROPS structure has been removed
from the tractor.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
S. Differential Lock Pedal
U. Hazard Light Switch—If Equipped
Diff. Lock
Pedal
Symbol
Figure 10
Figure 8
The hazard light switch is a rocker type switch
located to the left of the steering wheel on the dash
panel. Push the top of the hazard light switch
downward to activate the flashing amber lights.
Located at the front of the left running board, the
differential lock pedal engages the transmission
differential lock.
The differential lock is used to gain additional trac-
tion when operating the tractor on wet or loose soil.
When the pedal is depressed the rear wheels of the
tractor are prevented from rotating independently of
one another.
WARNING: Always activate the flash-
ing hazard lights when operating the
tractor on, or near, roadways.
V. Headlight Switch
WARNING: When operating with the
differential lock engaged, the tractor
will be difficult to steer. Do not drive
the tractor on roadways or at high
speeds with the differential lock
engaged.
Headlight
Switch
Symbol
Figure 11
NOTE: Disengagement of the differential lock is
recommended prior to turning the tractor on grass
or other maintained surfaces — tire damage to the
turf could occur.
The headlight switch is a rocker type switch located
to the left of the steering wheel on the dash panel.
Push the top of the headlight switch downward to
turn on the headlights and instrument panel gauge
lights.
T. Choke Control Knob
The choke knob controls the position of the engine
choke. Pull the knob out to choke the engine; push
the knob in to open the choke.
W. ROPS (Rollover Protective Structure)
The ROPS is installed to prevent or reduce injuries
to the operator should the tractor accidentally
overturn. The protection provided by the ROPS is
minimized if the seat belt is not used. For those
models equipped with a foldable ROPS - this
feature allows the ROPS to be lowered when
operating in areas with low overhead clearance.
Choke
Knob
Figure 9
12
Download from Www.Somanuals.com. All Manuals Search And Download.
X. Instrument Panel
Green
Range
7
3
4
2
1
HOURS 1/10
RPM
FUEL
E
F
0
4
x1000
5
6
Figure 12
5. PTO Engaged Indicator
1. Fuel Gauge
The fuel gauge monitors the fuel level in the fuel
tank. The needle pointing to the right indicates a full
tank. The ignition switch must be in the ON position
to activate the fuel gauge.
This indicator illuminates whenever the PTO switch
is pulled upward in the "ENGAGED" position while
the key switch is turned to the "ON" position. Check
this indicator if the engine will not crank with the key
switch in the "START" position—the indicator should
not be illuminated. If necessary, move the PTO
switch to the "DISENGAGED" position.
2. Tachometer
The tachometer shows the engine speed in revolu-
tions per minute (RPM). Optimal engine operating
speed is approximately 3400-3600 RPM. When
operating PTO driven attachments the RPM indica-
tor needle must be within the green range on the
tachometer dial.
6. Brake Engaged Indicator
This indicator illuminates whenever the brake pedal
is fully depressed or the parking brake is engaged
and the key switch is turned to the "ON" position.
Check this indicator if the engine will not crank when
the key switch is turned to the "START" position—
the indicator should be illuminated. If necessary,
fully depress the brake pedal.
3. Battery Indicator Light
•
Bulb illuminates and battery voltage is displayed
briefly when the ignition switch it turned to the
"ON" position.
•
Illuminates to indicate the battery voltage has
dropped below 11.5 (+0.5/-1.0) DC volts. The
battery voltage is also displayed on the hour
meter. If this indicator and display come on
during operation, check the battery and charging
system for possible causes and/or contact your
Cub Cadet dealer.
7. Hour Meter/Battery Display
The hour meter records the hours and tenths of an
hour (right most digit) that the tractor has been
operated.
•
The hour meter is activated when the key switch
is turned to the “ON” switch position. Because
the key switch may be accidentally left in the
"ON" position, a record of the actual hours of
operation should be kept to assure mainte-
nance procedures are completed according to
the schedule in this manual.
4. Oil Pressure Indicator
This warning lamp indicates low engine oil pressure.
If this indicator illuminates, stop the tractor
immediately and check the engine oil level. If the oil
level is within the operating range, but the light
remains on, contact your Cub Cadet dealer. NOTE:
The oil pressure indicator may illuminate when the
key switch is turned to the on position, but should
turn off when the engine is started.
•
When the key switch is turned to the "ON" posi-
tion, the battery indicator light briefly illuminates
and the battery voltage is briefly displayed. The
display then changes to the accumulated hours.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: OPERATION
ROLLOVER PROTECTIVE STRUCTURE (ROPS)
MODELS EQUIPPED WITH A FOLDING ROPS
This tractor is equipped with a Rollover Protection
Structure (ROPS) and seat belts. When used
together they are effective in reducing injuries to the
operator in the event of an accidental tractor
rollover. The safety provided by the ROPS is
minimized if the seat belt is not properly adjusted
AND buckled. Refer to ADJUSTMENTS for seat
belt adjustment.
The foldable ROPS feature allows the operator to
quickly lower the ROPS to operate in areas where
there is low overhead clearance. However, the
ROPS should be used in the lowered position only
when absolutely necessary. Operate with the
ROPS in the ‘up’ position whenever possible.
WARNING: A folded ROPS does not
provide rollover protection. When the
ROPS is in the folded position, the seat
belt must NOT be used.
ROPS
Reposition the ROPS as follows:
•
•
•
Loosen the two clamp knobs on the front of the
ROPS to relieve their pressure on the ROPS.
See Figure 14.
SEAT
BELT
Remove the two internal cotter pins, and, while
supporting the ROPS, withdraw the hitch pins.
See Figure 14. Carefully lower the ROPS.
Reinstall the hitch pins and internal cotter pins
for storage.
HITCH
PIN
Figure 13
INTERNAL
COTTER PIN
WARNING: Always wear the seat belt
when operating the tractor equipped
with a ROPS. However, if the ROPS is in
the folded position or has been re-
moved, the seat belt must not be used.
CLAMP
KNOB
HITCH
PIN
Use the following guidelines when using a tractor
equipped with a ROPS:
•
Be aware of overhead clearances in the area of
operation. Check for clearance of door (or gate)
openings and other overhead objects such as
utility lines and tree branches. Overhead
objects could catch the ROPS and upset the
tractor.
•
•
Do not modify the ROPS by drilling holes for, or
welding accessories to the structure.
Do not use the ROPS to pull objects with the
tractor. Use ONLY the tractor rear tow plate for
pulling.
Figure 14
To raise the ROPS:
•
•
•
Remove internal cotter pins and hitch pins and
lift the ROPS into position.
•
In the event of an accident, have the ROPS
carefully inspected and, if necessary, replaced
by your Cub Cadet dealer. Do not attempt to
repair the ROPS.
Insert the hitch pins and secure with the
internal cotter pins.
Tighten the clamp knobs against the ROPS.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INTERLOCK SYSTEM
The fuel fill cap is located on the fender to the left of
the seat. Unscrew the fuel cap and fill tank from an
approved gasoline container. Immediately wipe up
any spilled fuel.
This tractor is equipped with a safety interlock sys-
tem for the protection of the operator. If the interlock
system should ever malfunction, do not operate the
tractor. Contact your authorized Cub Cadet Dealer.
The safety interlock system prevents the engine
from cranking or starting unless the brake pedal is
fully depressed, and the PTO is “OFF”.
WARNING: Never fill the fuel tank to
the top of the filler neck. Expansion
could result in overflow through the
vents in the cap, allowing highly
flammable fuel to come in contact with
the operator.
•
The safety interlock system will shut off the
engine if the operator leaves the seat before
engaging the parking brake.
NEW TRACTOR BREAK-IN PROCEDURES
•
The safety interlock system will shut off the
engine if the operator leaves the seat with the
PTO “ON”, regardless of whether the brake
lock is engaged.
NOTE: The PTO switch must be moved to the
“OFF” position to restart the engine.
Proper care during the first hours of operation will
help to assure optimal performance from your new
tractor.
•
•
•
Never operate a new engine immediately under
full load. Allow the engine to warm up.
•
The safety interlock system will shut off the
PTO if the reverse control pedal is depressed,
unless the reverse override function is
activated.
NOTE: If the reverse override function has
been activated, it will remain activated until the
ignition switch is turned to the "OFF" position
for a 20 second duration.
Avoid operating the engine for prolonged periods
at either high or low speed with no load.
Use the transmission’s low speed range for
heavy loads to avoid lugging down or stalling
the engine due to overload.
•
•
Closely monitor the engine oil and keep filled to
the recommended level.
After the first ten hours of operation, check the
front wheel lug bolts and rear wheel lug nuts. If
necessary, retorque to 60-70 ft. lbs.
FUELING THE TRACTOR
Fill the fuel tank with only clean, fresh, unleaded
regular grade gasoline with a minimum octane
rating of 87. If engine knocking or pinging occurs,
use a different source of gasoline or a higher
octane rating.
•
Perform all break-in maintenance procedures
found in the MAINTENANCE section.
STARTING THE ENGINE
WARNING: Always sit in the operator’s
Oxygenated Fuels. Some fuels, called oxygenated
or reformulated gasoline, are gasoline blended with
alcohols or ethers. Gasoline blended with either
ethyl alcohol (maximum 10% by volume) or methyl
tertiary butyl ether (MTBE, maximum 15%) are
approved as fuels for the engine, provided they
meet the minimum octane rating requirement. Other
gasoline/alcohol or gasoline/ether blends are not
approved for use in the tractor’s engine. If any
undesirable operating symptoms occur, use
gasoline with a lower percentage of alcohol or ether.
seat when starting the tractor. Never
start the tractor from any other
position.
•
•
Operator must be sitting in the tractor seat.
Pull the choke control knob out to the full choke
position. Less choking may be necessary due
to variations in temperature, grade of fuel, etc.
Little or no choking will be needed when the
engine is warm.
Purchase fuel in a quantity that can be used within
30 days to assure fuel freshness. Do not use
gasoline left over from the previous season to
minimize gum deposits in the fuel system.
•
Make sure the PTO switch is in the “OFF”
position. NOTE: The PTO light on instrument
panel will be lit if the switch is in the "ON"
position.
WARNING: Gasoline is extremely
flammable and can be explosive in
certain conditions. Do not fill the fuel
tank when the engine is running or
while the engine is hot. Tighten the
fuel cap securely.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Move the throttle handle to midway between
the “SLOW” and “FAST” position. Refer to
Figure 15.
•
•
Allow the engine to run for a few minutes at mid
throttle before putting the engine under load.
Observe the instrument panel. If the battery
indicator light or oil pressure light come on,
immediately stop the engine. Have the tractor
inspected by your Cub Cadet dealer.
THROTTLE
HANDLE
SLOW
COLD WEATHER STARTING
Be sure to use the proper oil for the expected
temperatures and use winter grade fuel. Follow the
normal engine starting instructions above.
However, allow the engine ample time to warm up
before putting the tractor under load.
FAST
PTO SWITCH
IN ‘OFF’
USING JUMPER CABLES TO START ENGINE
POSITION
WARNING: Batteries contain sulfuric
acid and produce explosive gasses.
Make certain the area is well ventilated,
wear gloves and eye protection, and
avoid sparks or flames near the battery.
Figure 15
•
•
Either fully depress and hold the brake pedal or
engage the parking brake. NOTE: The parking
brake indicator on instrument panel will light
when the pedal is properly depressed.
If the battery charge is not sufficient to crank the
engine, recharge the battery. If a battery charger is
unavailable and the tractor must be started, the aid
of a booster battery will be necessary. Connect the
booster battery as follows:
Turn the ignition key clockwise to the “START”
position and release it as soon as the engine
starts; however, do not crank the engine
continuously for more than 10 seconds at a
time. If the engine does not start within this
time, turn the key to “OFF” and wait a minute to
allow the engine’s starter motor to cool. Try
again after waiting. If after a few attempts the
engine fails to start, do not keep trying to start it
with the choke closed as this will cause flooding
and make starting more difficult. Instead, fully
open the choke and start the engine.
•
Connect the end of one cable to the disabled
tractor battery’s positive terminal; then connect
the other end of that cable to the booster
battery’s positive terminal.
•
•
Connect one end of the other cable to the
booster battery’s negative terminal.
Connect the other end of that cable to the
frame of the disabled tractor, as far from the
battery as possible.
NOTE: Upon start-up, a metallic ticking noise may
occur. This is caused by hydraulic lifter leakdown
during storage. The noise will normally cease within
the first minutes of engine warm up. If the noise
continues, increase the engine speed to mid-throttle
and allow the engine to run for several minutes. If
the noise persists, contact your Cub Cadet dealer.
•
•
Start the disabled tractor following the normal
starting instructions previously provided; then
disconnect the jumper cables in the exact
reverse order of their connection.
Have the tractor’s electrical system checked
and repaired as soon as possible to eliminate
the need for jump starting.
WARNING: If the starter disengages the
engine flywheel, but the engine does
not continue to run, allow the engine to
STOPPING THE ENGINE
•
•
Place the PTO switch in the “OFF” position.
come to
a
complete stop before
Place the throttle control lever somewhere
between the mid and full throttle position.
attempting to restart the engine. Dam-
age to the starter may result from
failure to do so.
•
Turn the ignition key to the “OFF” position and
remove the key from the ignition switch.
•
After the engine starts, slowly release the brake
pedal. As the engine warms up, gradually push
the choke control knob all the way in. Do not
use the choke to enrich the fuel mixture, except
as necessary to start the engine.
NOTE: Always remove the key from the ignition
switch to prevent accidental starting or battery
discharge if the equipment is left unattended.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVING THE TRACTOR
WARNING: Avoid sudden starts, exces-
•
•
Turn the ignition switch to “OFF’” and remove
the key from the switch before dismounting.
Depress the button in the center of the seat belt
buckle to release the seat belt.
sive speed and sudden stops.
WARNING: Do not leave the seat of the
tractor without disengaging the PTO
and engaging the parking brake. If
leaving the tractor unattended, turn the
ignition key off and remove key.
USING THE FORWARD AND REVERSE PEDALS
The hydrostatic transmission provides constantly
variable ground speeds within the speed rating of
each (HI/LO) transmission range. The tractor speed
is controlled by the forward and reverse pedals on
the front of the right running board.
•
Adjust the operator’s seat to the most comfort-
able position that allows you to operate all
controls and pedals. See seat adjustment in the
ADJUSTMENTS section.
The forward and reverse pedals are self neutraliz-
ing. The transmission and pedals return to neutral
when the pedals are released and the tractor will
slow to a stop. NOTE: Use the brake pedal to stop
the tractor.
WARNING: DO NOT use the seat belt if
the ROPS has been lowered or
structure has been removed from the
tractor.
•
To move forward, slowly depress the forward
control pedal (See Figure 16) until the desired
speed is achieved. The speed of the tractor is
directly related to the distance the pedal is
depressed.
•
•
Adjust the seat belt to fit snugly but comfortably
around your lap, then buckle the seat belt.
Refer to ADJUSTMENTS section.
Shift the transmission Hi/Lo range shift lever on
the left fender to the desired speed setting.
Refer to USING THE HI/LO RANGE SHIFT
LEVER sub-section below.
PARKING
BRAKE
BRAKE
PEDAL
LEVER
•
Use the tractor and/or auxiliary hydraulic lift
lever(s) to raise all tractor attachments from the
ground if transporting the tractor to a work site.
•
•
Depress the brake pedal to release the parking
brake, then slowly release the brake pedal.
Move the throttle handle to the position where
the engine operates best for the load to be
handled (normally 3500-3600 RPM).
Depress
to go in
Reverse
Depress
to go
Forward
•
Slowly depress either the forward or reverse
pedal to move the tractor in the desired
direction. Refer to USING THE FORWARD
and REVERSE PEDALS in paragraphs below.
Figure 16
STOPPING THE TRACTOR
•
To move in reverse, check that the area behind
is clear then slowly depress the reverse control
pedal. Refer to Figure 16.
•
Fully depress the brake pedal to bring the
tractor to a complete stop. Push downward on
the parking brake lever and release the pedal
to engage the parking brake. See Figure 16.
NOTE: Do not use the forward or reverse control ped-
als to change the direction of travel when the tractor is
in motion. The abrupt direction change may unseat
the operator and will cause premature wear in the
transmission. Allow the tractor to stop before chang-
ing directions.
•
•
Depress the rear of the PTO switch to
disengage the PTO.
Place the throttle control lever somewhere
between the mid and full throttle position.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE HI/LO RANGE SHIFT LEVER
DRIVING ON SLOPES
WARNING: Do not operate on inclines
WARNING: The tractor must be
stopped before engaging or disengag-
ing the transmission Hi/Lo range shift
lever. Shifting while the tractor is in
motion will cause damage to the
transmission.
with a slope in excess of 15 degrees (a
rise of approximately 2-1/2 feet every
10 feet). The tractor could overturn and
cause serious injury.
IMPORTANT: Always shift the transmission
into the LOW speed range BEFORE beginning
the climb or descent of any slope.
WARNING: Always maintain a tractor
speed that allows for complete control
and stability of the machine. Be aware
of dangerous areas or conditions.
Operate the tractor up and down slopes, never
across slopes. Do not drive so that the tractor may
tip over sideways
Referring to Figure 17, pull the lever to the right
side of the slot to clear the shift gate, then shift the
lever as follows :
Before operating the tractor on a slope, walk the
slope to look for possible hazards such as rocks,
mounds, stumps, or surface irregularities which
could cause the tractor to be upset.
PTO REVERSE
LOW
N
OVERRIDE
Back the tractor with attachment up the steepest
portion of each slope you intend to work. If the
tractor cannot negotiate the slope in reverse, the
slope is too steep to be worked.
SWITCH
HI
Avoid turns when driving on a slope. If a turn must
be made, turn down the slope. Turning up a slope
greatly increases the chance of a roll over.
Avoid stopping when driving up a slope. If it is
necessary to stop while driving up a slope, start up
smoothly and carefully to reduce the possibility of
flipping the tractor over backward.
HI/LO RANGE
SHIFT LEVER
SHIFT GATE
Figure 17
USING THE DIFFERENTIAL LOCK PEDAL
HI range — Shift the lever fully forward in slot.
Forward speed 0 to 8.0 mph.
Depressing the differential lock pedal engages a
mechanism in the transmission that locks the
differential. This prevents the rear wheels from
rotating independently of each other and provides
constant power to both rear wheels when additional
traction is needed.
Reverse speed 0 to 4.0 mph.
Hi range is normally used for transport and can be
used with some tractor attachments
LOW range — Shift the lever fully rearward in slot.
Forward speed 0 to 4.0 mph.
IMPORTANT: Do not engage the differential
lock when one of the rear wheels is rotating.
Stop the wheel rotation and then engage the
differential lock.
Reverse speed 0 to 2.0 mph.
Low range is recommended for use with most PTO
driven tractor attachments. Low range must be
used when climbing or descending slopes.
WARNING: When operating with the
differential lock engaged, the tractor
will be difficult to steer. Do not drive
the tractor on roadways or at high
speeds with the differential lock
engaged.
NEUTRAL — Shift the lever to the center of slot.
Disengages the transmission drive.
Use ONLY for towing or moving the tractor when
not under power.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Fully depress and hold the differential lock
pedal to engage the transmission differential
lock. Release the pedal to disengage the
differential lock. See Figure 18.
•
•
Move the lift lever rearward in the slot to raise
the equipment.
Move the lift lever fully forward and to the right
ahead of the float lock gate to lock the lift in the
float position.
ENGAGING THE PTO
WARNING: The operator must be in the
seat at all times when the PTO is
engaged. If the operator should leave
the seat without turning off the PTO
switch, the tractor’s engine will shut off.
DIFFERENTIAL
LOCK PEDAL
(Depress and
Hold to Engage)
•
•
Move the throttle handle to the mid throttle
position. See Figure 20.
Push the top of the PTO switch downward to
engage the PTO (See Figure 20). The PTO
light on the instrument panel will come on.
Figure 18
•
Observing the tachometer on the instrument
panel, use the throttle handle to increase the
engine speed to the PTO operating range
(3400-3600 rpm).
NOTE: Because of the drive load on the internal
engagement mechanism, releasing the differential
lock pedal may not always disengage the
differential lock. It may be necessary to slow the
tractor, or reverse the direction of travel, to
disengage the differential lock.
THROTTLE HANDLE
USING THE HYDRAULIC LIFT LEVER
The hydraulic lift system provides power for raising
and positioning three point hitch and belly mounted
equipment. To raise an attachment using the
hydraulic lift system, the engine must be running.
Generally, an attachment can be lowered with the
engine running or off.
Mid Throttle
to Engage
3500 RPM
to Run
•
Move the lift lever forward in the slot to lower
the equipment to the desired height setting.
Refer to Figure 19.
PTO SWITCH
Figure 20
Raise
•
Push the bottom of the switch downward to
disengage the PTO.
Lower
Float
IMPORTANT: Normally the PTO will not
operate when the tractor is driven in the reverse
direction. The PTO reverse override switch
must be activated to operate the PTO while
traveling in reverse.
HYDRAULIC
LIFT LEVER
FLOAT LOCK
GATE
Figure 19
19
Download from Www.Somanuals.com. All Manuals Search And Download.
USING THE PTO REVERSE OVERRIDE SWITCH
Use of the headlights, along with a SMV (Slow
Moving Vehicle) emblem, is also recommended
when operating the tractor on or near roadways to
increase visibility to traffic.
The PTO reverse override switch, located on the
left fender, allows the PTO to operate while the
tractor is traveling in the reverse direction. See
Figure 21.
HAZARD LIGHTS
PTO REVERSE
OVERRIDE
SWITCH
Always use the flashing amber hazard lights along
with the SMV (Slow Moving Vehicle) emblem when
operating the tractor on, or near, roadways. Also
activate the hazard lights when necessary to warn
others that the tractor is being operated in the area.
•
To turn on the flashing hazard lights, depress
the top end of the hazard light switch located to
the left of the headlight switch.
•
To turn off the hazard lights, depress the
bottom of the light switch.
USING THE TOP LINK RETAINER HOOK
Figure 21
The top link hook is provided to retain the top link of
the three point hitch when not in use.
•
•
The PTO should first be engaged using the
PTO switch on the dash panel.
To utilize the top link hook, proceed as follows:
Depress the front of the override switch to
activate the reverse override system. The light
in the override switch will come on.
•
•
Manually lift the 3-pt. hitch top link fully upward.
Pivot the link hook from its storage position to
the center and lower the top link into the hook
of the rod. See Figure 22.
IMPORTANT: Once activated, the reverse
override will remain activated until the ignition
switch is turned to the OFF position. If the over-
ride switch is illuminated, the system is
activated.
IMPORTANT: When using the three point
hitch, the retainer hook must be pivoted fully
rearward to avoid interference with the top link.
WARNING: Use EXTREME CAUTION
when operating PTO driven attach-
ments while traveling in the reverse
direction.
TOP LINK
HOOK
TOP
LINK
HEADLIGHTS
Always use the headlights for after dusk and pre-
dawn operation of the tractor. The lights not only
illuminate the work area, but also increase the
visibility of the tractor for anyone who might enter
the area of operation.
•
To turn on the headlights, depress the top end
of the headlight switch located to the left of the
steering wheel.
•
To turn off the headlights, depress the bottom
of the light switch.
Figure 22
20
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOVING THE REAR PTO COVER
IMPORTANT: When transporting pull-behind
equipment on public roadways, always use a
safety chain to supplement the connection
between the tractor and towed equipment. The
safety chain must have a strength rating equal
to or greater than the gross weight of the equip-
ment being towed.
The rear PTO cover is a safety feature designed to
prevent items from accidentally being caught by the
rotating shaft. The cover should be removed only
when the rear PTO is being utilized.
To remove and reinstall the cover, proceed as
follows:
•
Loosen the two screws on the left side of the
cover. Refer to Figure 23.
USING THE THREE POINT HITCH
WARNING: Always disengage the PTO,
stop the engine, and set the parking
brake before dismounting the tractor
to connect, disconnect, or adjust three
point hitch mounted implements.
•
Slide the cover to the right until the slots of the
cover are free of the screws and pull the cover
off. See Figure 23.
REAR PTO
SHAFT
Use the rear three point hitch system to attach
three point mounted implements, which are
normally driven by the rear PTO. Use the tractor’s
hydraulic lift system to raise and lower the three
point hitch and set the height position of the
implement.
PTO
COVER
SLOTS
Refer to the ADJUSTMENTS section for instruc-
tions on adjusting the RH adjustable lift link, top
hitch link, and hitch chains. See Figure 24.
Slide to Right
and Pull Off
TOP
HITCH LINK
ADJUSTABLE
LIFT LINK
HEX SCREW
Figure 23
FIXED
LIFT
LINK
•
When finished using the rear PTO, slide the
cover fully onto the shaft; then slide the cover
to the left until the slots are underneath the
screw heads. Tighten the screws to secure the
cover. Refer to Figure 23.
USING THE HITCH PLATE
HITCH
PLATE
Use only the hitch plate (Refer to Figure 24), for
towing pull-behind equipment (carts, trailers, etc.)
or dragging loads.
HITCH
CHAIN
Raise the lower links of the three point hitch to their
highest position to prevent interference with the
towed equipment.
LOWER HITCH LINK
Figure 24
21
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTOR WEIGHTING
Front Weights
When implements are installed on either the front or
rear of the tractor, the normal balance of the tractor
is altered.
To counterbalance three point hitch mounted
equipment, a weight bracket/bumper kit and cast
iron weights are available from your Cub Cadet
dealer. Refer to the Weighting Table for the proper
ballast to be added to the front of the tractor.
•
As a rear mounted implement is raised to the
transport position, the balance point of the
tractor shifts rearward, which may result in a
loss of steering control and tractor stability.
Weighting the Rear of the Tractor
To counterbalance front mounted equipment, use a
rear weight box, and/or liquid ballast in the rear
tires. Refer to the Weighting Table for the proper
ballast to be added to the rear of the tractor.
•
When a front mounted implement is raised, the
balance point shifts forward and may result in a
loss of traction and stability.
To counterbalance these weight shifts, weight
should be added to the tractor in the form of either
front cast iron weights, a rear weight box, and/or
liquid tire ballast. Only enough weight should be
added to obtain good traction, control, and stability.
Excessive weight will unnecessarily load down the
tractor’s engine and transmission.
NOTE: Consult with your Cub Cadet dealer about
having liquid ballast added to your tires, and for any
special maintenance after the procedure is
performed. Because special equipment and a
familiarity with the practice is required, only a
qualified tire technician should perform this
procedure.
INSTALL ONLY EQUIPMENT APPROVED FOR
USE ON THE 5000 SERIES TRACTOR.
TRACTOR WEIGHTING TABLE
Equipment Installed
on Tractor
Method of Weighting
Weight Required
Rear Mounted Finish
Mower
Front Weight Bracket and
Suitcase Weights
A minimum of four suitcase weights (168 pounds)
Rear Mounted Tiller
Front Weight Bracket and
Suitcase Weights
Front Weight Bracket and
Suitcase Weights
A minimum of two suitcase weights (84 pounds)
A minimum of two suitcase weights (84 pounds)
A minimum of four suitcase weights (168 pounds)
Rear Mounted Blade,
Box Blade, Rake
Rear Mounted Post Hole Front Weight Bracket and
Digger
Front Snow Thrower
Front Blade
Suitcase Weights
None Required
None Required
None Required
None Required
** If the center of gravity of the additional weight is positioned closer to the rear axle and higher above the
ground, more weight must be added. If the additional weight is carried farther from the axle and lower, less
weight may be used.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: ADJUSTMENTS
ADJUSTING THE SEAT
Adjust the final length of the seat belt using the
adjuster clip, buckle link, and upper belt webbing on
the right half of the belt.
For the comfort of the operator, a single lever
adjustable seat is provided to set the fore to aft
position of the seat. Adjust the seat to the most
comfortable position that allows you to operate all
controls and pedals.
•
•
•
To lengthen the belt, hold the ends of the
adjuster clip and tip upward the side of the clip
toward the buckle link. See Figure 26.
While holding the clip, pull the upper webbing
of the belt through the clip toward the buckle
link. See Figure 26.
WARNING: Do not adjust the seat when
the tractor is moving, as this could
cause the operator to lose momentary
control of the tractor and result in an
accident.
Hold the belt and pull the buckle link to the left
to remove the slack in the upper webbing of the
belt between the adjuster clip and the link.
•
•
To adjust the seat, pivot the seat adjustment
lever to the left and hold while repositioning the
seat to the desired position.
Tip Sides of Clip
BUCKLE
RELEASE
BUTTON
Pull Belt to
Shorten
Pull Belt to
Lengthen
After repositioning the seat, release the lever to
lock the seat in position. Slide the seat either
slightly forward or rearward to assure it is
locked, or until engagement of the lock is felt.
See Figure 25.
ADJUSTER
CLIP
LOWER
WEBBING
BUCKLE
LINK
UPPER
WEBBING
SEAT
ADJUSTMENT
LEVER
Figure 26
•
To shorten the belt, tip the other side of the clip
upward, pull the free end of the belt webbing to
the right, and pull the buckle link to the left to
remove the slack.
THREE POINT HITCH ADJUSTMENTS
Pivot Lever
to Left
•
Adjust the RH adjustable lift link to level the
lower hitch links. Loosen the jam nut and turn
the adjustment tube as shown in Figure 27 to
shorten or lengthen the lift link. Tighten the jam
nut against the adjustment tube after adjusting.
Figure 25
ADJUSTING THE SEAT BELT
WARNING: Always wear the seat belt
when operating the tractor equipped
with a ROPS. If the ROPS has been
removed, the seat belt should not be
used.
JAM
NUT
Loosen
Jam Nut
ADJUSTMENT
TUBE
Shorten
NOTE: If the belt is too long or too short to be prop-
erly adjusted using the upper belt webbing, the
adjustment clip should be repositioned. To do so,
firmly grasp the adjustment clip and pull the lower
webbing though the clip. Move the clip toward the
anchor point at the seat to shorten the belt, or
toward the buckle link the lengthen the belt.
Lengthen
Figure 27
23
Download from Www.Somanuals.com. All Manuals Search And Download.
•
The length of the upper hitch link is normally
determined by the design of each implement.
To adjust the upper hitch link, loosen the lock-
ing lever and turn the adjustment tube as
shown in Figure 28. After the appropriate length
is attained, tighten the locking lever. If correctly
adjusted, the upper hitch link will be parallel or
nearly parallel to the lower hitch links.
•
Distance ‘A’ should be 1/8"-1/4" less than
distance ‘B’ if the toe-in is correct. If it is not,
readjust the toe-in.
A
ADJUSTMENT
TUBE
Lengthen
Shorten
LOCKING
LEVER
Loosen
Lock Lever
B
Figure 28
Figure 30
•
The length of the hitch chains limit the side-to-
side movement of the hitch lower links. To
adjust the length of the hitch chains, loosen the
jam nut and turn the hex collar on the adjust-
ment rod as shown in Figure 29. Tighten the
jam nut after adjusting.
READJUST THE TOE-IN AS FOLLOWS:
NOTE: The left ball joint and jam nut are left hand
threaded.
•
•
Loosen the jam nuts at both the LH and RH ball
joints. See Figure 31.
HEX COLLAR
ON ROD
Slide an open-end wrench onto the flat area at
either end of the tie rod and turn the tie rod as
follows:
HEX JAM NUT
Turn Hex Collar
to Shorten
Rearward to shorten the tie rod and increase
the toe-in. See Figure 31.
Turn Hex Collar
to Lengthen
ADJUSTMENT
ROD
Forward to lengthen the tie rod and decrease
the toe-in. See Figure 31.
Figure 29
Front of
Tractor
ADJUSTING FRONT WHEEL TOE-IN
The front wheel toe-in is set at the factory and
should maintain the proper setting. However, the
toe-in should be checked periodically and
readjusted if necessary.
Increase
Toe-in
Decrease
Toe-in
CHECK THE TOE-IN AS FOLLOWS:
•
Place the tractor on a level surface with the
wheels in the straight ahead position.
TIE ROD
•
Place an easily visible mark on the center lines
of both front tires at the horizontal center line of
the wheel.
JAM NUT
RH BALL JOINT
•
•
Measure and record the distance ‘A’ between
the two marks. See Figure 30.
Figure 31
Roll the tractor forward or rearward until the
marks are at the horizontal center line at the
rear of the wheels. Measure and record the
distance ‘B’ between the marks. See Figure 30.
•
Readjust the tie rod as necessary to obtain the
correct toe-in, then tighten the jam nuts against
the ball joints.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING THE BRAKES
puck and the brake disc. The gap should mea-
sure between .012 and .015". See Figure 32.
The tractor brakes are adjusted at the factory and
should experience minimal wear if the tractor is
operated normally. However, all brake pads are
subject to wear and at some point the brake linkage
may have to be adjusted.
•
•
If the gap is greater than .015", tighten the hex
nut on the brake assembly until the gap is
within the tolerance.
Position the ferrule to align with the hole in the
brake pedal. If the ferrule does not align with
the hole, loosen the jam nut by turning it away
from the ferrule
Check the brakes as follows:
•
Place the tractor on a level surface. Stop the
tractor engine.
•
Adjust the ferrule on the brake rod to align with
the brake pedal hole, then tighten the jam nut
against the ferrule.
•
From beneath the RH running board, remove
the internal cotter pin to disengage the brake
rod ferrule from the brake pedal. Position the
brake rod to make certain there is no pull on
the brake actuator arm. See Figure 32.
•
•
Insert the ferrule in the brake pedal and secure
with the internal cotter pin.
•
From the rear of the tractor, use a feeler gauge
to measure the gap between the outer brake
Repeat the previous steps to check and, if
necessary, adjust the LH brake assembly.
INTERNAL
COTTER PIN
JAM NUT
FERRULE
RH BRAKE ROD
GAUGE
.012 - .015"
BRAKE
ACTUATOR
ARM
BRAKE PEDAL
BRAKE DISC
HEX NUT
Figure 32
25
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: TRACTOR MAINTENANCE
The service life and reliability of any machine
depends upon the care it is given. Proper lubrica-
tion and maintenance is a vital part of that care.
Using the Lubrication and Maintenance Chart as a
guide, monitor the hourmeter on the instrument
panel to ensure the required maintenance proce-
dures are performed. The maintenance schedule
reflects the minimal requirements to maintain the
equipment. More frequent inspections and mainte-
nance is preferable.
Apply pressure until clean grease emerges from the
lubrication point.
Miscellaneous working parts not provided with
lubrication fittings should be oiled regularly with a
good grade of lubricating oil.
Lubricate the tractor thoroughly before taking it to a
remote location for a prolonged period of time.
Lubricant is cheap. Use plenty of it. Worn parts can
be expensive to replace.
Make certain that all lubrication fittings are installed
and functioning. Wipe away all old grease and dirt
from the lube fittings to prevent foreign materials
from entering as the new grease is applied. Use a
pressure lubricating gun to force in new grease.
Store your supply of lubricating grease and oil in
clean, covered containers to protect them from dust
and dirt. Keep the lubricating gun nozzle clean.
LUBRICATION TABLE
General Information
Type of
Application
API
Anticipated
SAE
Lubricant
Capacity Classifi-
cation
Description
Ambient
Temp.
Viscosity
5W-20 †
5W-30 †
Use High
Quality Engine Oil
Below 32°F
Approx.
2.1 Qts.
w/Filter
SG,
SH,
or
Engine
Oil
Engine
Cub Cadet
737-3030A (1Qt.)
0°F to 100°F
10W-30 †
SJ
Hydrostatic
Transmission
and
Hydraulic
System
Use Cub Cadet
Drive System Fluid Plus
737-3120 (1 Qt.)
Approx.
20 Qts.
(5.0 Gal.)
Cub Cadet
Drive System
Fluid Plus
737-3121 (1 Gal.)
As
Needed
Use Cub Cadet
251H EP Grease
737-3034 (14.5 Oz. Cartridge)
Lube
Fittings
Grease
† Using multi grade oils (5W-20, 5W-30, and 10W-30) will increase oil consumption. Check the engine
oil level frequently when using them.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION AND MAINTENANCE CHART (ILLUSTRATION)
18
9
9
7
6
11
4
1
2
3
10
16
15
12
8
17
4
5
4
13
14
12
13
5
27
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION AND MAINTENANCE CHART
Service Intervals
Ref.
No.
Operation to
be Performed
1
2
3
Check Engine Oil Level
Check Air Cleaner
•
•
Clean Air Cleaner Foam
Precleaner Element
†
4
5
Change Engine Oil and Replace
Oil Filter
•
•
•
Retorque Front Wheel Lug Bolts
and Rear Wheel Lug Nuts
first
10
hours
6
7
Check Transmission Oil Level
•
Replace Hydrostatic
Transmission Oil Filter
first
25
hours
•
8
Replace Hydraulic System Filter
first
25
•
hours
9
Replace Hydraulic/Hydrostatic
Oil
•
10
Replace Air Cleaner Paper
Element
†
11
12
13
14
15
Grease Drive Shaft (both ends)
Grease Front Steering Knuckles
Grease Front Axle Wheel Hubs
Grease Front Pivot Axle
•
•
•
•
•
•
•
•
•
Grease Power Steering Cylinder
(both ends)
•
16
17
18
Clean and Re-gap Spark Plugs
Check Fuel Filter
•
•
•
Grease Three Point Lift Shaft
•
† More often when operating under dusty conditions.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSING THE ENGINE COMPARTMENT
•
If acid spills on clothing, first dilute it with clean
water, then neutralize with a solution of
ammonia/water or baking soda/water.
WARNING: If the tractor has been
recently operated, engine surfaces will
be HOT. Allow the engine to cool
before opening the hood, or use
extreme caution to avoid burns when
the hood is open.
•
•
NEVER connect (or disconnect) battery charger
clips to the battery while the charger is turned
on, as it can cause sparks.
Keep all sources of ignition (cigarettes,
matches, lighters) away from the battery. The
hydrogen gas generated during charging can
be combustible.
Locate the hood notch at the front of the tractor.
Depending on which type of hood latch is installed
on your tractor, raise the hood as follows:
•
Tractors with Latch Release Lever. Lift and
hold the latch release lever while lifting the
hood.
Tractors with Hood Latch Bracket. Pull the
hood latch bracket forward/upward to release
the front of hood; then lift hood. See Figure 33.
•
•
As a further precaution, only charge the battery
in a well ventilated area.
Always shield eyes and protect skin and
clothing when working near batteries.
•
WARNING: Batteries contain sulfuric
acid and may emit explosive gases.
Use extreme caution when handling
batteries. Keep batteries out of the
reach of children.
Hood
Notch
BATTERY REMOVAL
WARNING: Battery posts, terminals
and related accessories contain lead
and lead compounds. Wash hands
after handling.
Lift Hood
The battery is located at the front of the tractor
beneath the hood.
Lift Lever
Latch
To remove the battery:
Release
Lever
•
Open the tractor hood as described in the
previous sub-section.
•
Remove the two wing nuts and the battery
holddown strap from the battery holddown rods.
See Figure 34.
Pull Latch
to
Lift Hood
CABLE
CLAMP
HOLDDOWN STRAP
WING NUT
Hood
Latch
Figure 33
GENERAL BATTERY INFORMATION
WARNING:
•
•
Battery posts, terminals and related accesso-
ries contain lead and lead compounds. Wash
hands after handling.
BATTERY
TERMINAL
COVER
HOLDDOWN
ROD
Should battery acid accidentally splatter into
the eyes or onto the skin, rinse the affected
area immediately with clean cold water. If there
is any further discomfort, seek prompt medical
attention.
Figure 34
•
Spread the locking clips on the sides of the
terminal covers and lift the tops of the covers to
expose the battery connections. See Figure 34.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Loosen the cable clamp of the black negative
battery lead, then lift the negative cable and its
terminal cover off the negative battery post
(marked NEG). Move the cable away from the
negative battery post.
Repeat the above procedure to remove the
cable and cover from the positive battery post
(marked POS).
BATTERY STORAGE
•
•
•
When storing the tractor for extended periods,
disconnect the negative battery cable. It is not
necessary to remove the battery.
All batteries discharge during storage. Keep the
exterior of the battery clean, especially the top.
A dirty battery will discharge more rapidly.
•
•
The battery must be stored with a full charge. A
discharged battery can freeze sooner than a
charged battery. A fully charged battery will
store longer in cold temperatures than hot.
Carefully lift the battery out of the tractor.
Install the battery by repeating the above steps in
the reverse order.
•
Recharge the battery before returning to service.
Although the tractor may start, the engine charg-
ing system may not fully recharge the battery.
WARNING: Always connect the posi-
tive lead to the battery before con-
necting the negative lead. This will pre-
vent sparking or possible injury from
an electrical short caused by contact-
ing the tractor body with tools being
used to connect the cables.
HEAD LIGHT BULB REPLACEMENT
The tractor is equipped with headlights. If one of the
bulbs should burn out, replace the bulb as follows:
•
•
Fully raise the hood.
CHARGING THE BATTERY
Test and, if necessary, recharge the battery after
the tractor has been stored for a period of time.
Pull the wire harness plug from the bulb/socket
assembly to unplug the wire harness. See
Figure 35.
•
A voltmeter or load tester should read 12.6 volts
(DC) or higher across the battery terminals.
•
Charge the battery with a 12-volt battery
charger at a MAXIMUM rate of 10 amps.
REFLECTOR
Voltmeter
Reading
12.7
State of
Charge
100%
75%
Charging
Time
Full Charge
WIRE
HARNESS
PLUG
12.4
90 Min.
12.2
12.0
50%
25%
180 Min.
280 Min.
BULB/SOCKET
ASSEMBLY
BATTERY MAINTENANCE
The battery is filled with battery acid and then
sealed at the factory. However, even
Figure 35
a
“maintenance free” battery requires some
maintenance to ensure its proper life cycle.
•
Turn the bulb/socket assembly approximately a
quarter turn counterclockwise to align its tabs
with the notches of the reflector, then remove
from the reflector.
•
Spray the terminals and exposed wire with a
battery terminal sealer, or coat the terminals
with a thin coat of grease or petroleum jelly, to
protect against corrosion.
•
•
Replace with a new bulb/socket assembly (Cub
Cadet No. 725-04084).
Align the tabs of the new bulb/socket assembly
with the notches of the reflector and insert the
bulb.
•
•
•
Always keep the battery cables and terminals
clean and free of corrosion.
Always keep the terminal covers in place and
closed over the battery terminals.
•
Turn the bulb/socket assembly clockwise to
lock in place. Push the wire harness plug fully
into the bulb socket.
Avoid tipping. Even a sealed battery will leak
electrolyte when tipped.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
TRACTORS WITH HAZARD LIGHTS
Main Fuse
Hazard lights are installed on each side of the
ROPS. To replace the bulbs proceed as follows:
The main fuse in the tractor wire harness protects
the tractor’s entire electrical system. A blown main
fuse will prevent battery current from passing
though the harness.
•
Insert a thin bladed screwdriver, or similar tool,
between an amber lense and the hazard light
body, then twist to separate the lense from the
body. Refer to Figure 36.
To replace the main fuse:
•
•
Raise the tractor hood.
•
Push the bulb inward and turn counterclockwise,
then pull the bulb outward to remove from the
light socket. See Figure 36.
Locate the main fuse under the dash panel,
along the tractor’s right frame rail. See Figure 38.
SOCKET
WIRE
HARNESS
Push in
and Turn
AMBER
LENSE
DASH
PANEL
BULB
FUSE HOLDER
Figure 38
MAIN FUSE
BODY
•
•
Pull the fuse from the fuse holder and replace
with the same capacity fuse (30 Amp). NEVER
use a higher amperage fuse.
Figure 36
•
•
Align the new bulb with the socket slot, push
the bulb into the socket, and turn clockwise to
lock it in the socket.
Lower the tractor hood.
Accessing the Lower Dash Panel Area
Position the lense on the hazard light body and
push the lense onto the body until it snaps
firmly into place on the body.
Some electrical components are housed inside the
lower dash panel. To access the area, remove the
dash panel insert by removing the two screws. See
Figure 39.
SERVICING ELECTRICAL SYSTEM
Fuses are installed to protect the tractor’s electrical
system from damage caused by excessive amper-
age. Always use the same capacity fuse for
replacement. If the electrical system does not func-
tion, check for blown fuses. See Figure 37.
SCREWS
DASH
PANEL
INSERT
GOOD
BAD
Figure 37
Figure 39
If you have a recurring problem with blown fuses,
have the tractor’s electrical system checked by your
Cub Cadet dealer.
To reinstall the dash panel insert, hook the retaining
lip at the bottom of the insert over the bottom edge
of the dash opening, pivot the insert upward into
position, and secure with the two screws.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Tractors with Electric Fuse Center
Instrument Panel Fuses
Right Side
The instrument panel’s circuitry is protected by the
two fuses in the fuse center. If the instrument panel
does not function properly, check the fuses.
Pull the two fuses from the fuse center and check
their condition. Replace a blown fuse with the same
capacity fuse (3 Amp). Refer to Figure 41.
START
RELAY
PTO
RELAY
Relays
The PTO relay and starter relay, located in the fuse
center, maintain power to each of those circuits. If
one of the circuits is not functioning properly, have
your dealer electrically check the relay. See Figure
40.
CRUISE
CONTROL
RELAY
Left Side
(OPTIONAL)
INSTRUMENT
PANEL FUSES
(3 AMP)
REVERSE
OVERRIDE
RELAY
STARTER
RELAY
REVERSE
RELAY
PTO RELAY
Figure 41
Tractors with Hazard Lights - Flasher Relay
FUSE
CENTER
The flasher relay, which controls the on/off flashing
of the hazard lights, is located inside the lower dash
panel.
Figure 40
Replace the relay as follows:
Tractors with Pedestal Mounted Relays
Electrical Circuit Relays
Several relays, which operate electrical functions of
the tractor, are located inside the lower dash panel.
If one of the circuits is not functioning properly,
have your dealer electrically check the relay. See
Figure 41.
•
Pull the wire harness from the right side of the
dash opening and remove the electrical tape
from the flasher relay. Refer to Figure 42.
FLASHER
RELAY
•
•
Start Relay — Functions in the start circuit.
TAPE
PTO Relay — Operates in conjunction with
both the Reverse Relay and Reverse Override
Relay to engage the PTO.
WIRE
HARNESS
•
•
Reverse Relay — Functions with the PTO
Relay and Reverse Switch in the "No Cut in
Reverse" circuit.
Reverse Override Relay — Functions with the
Reverse Override Switch and PTO Relay to
maintain PTO engagement when driving in
reverse.
HARNESS
LEADS
Figure 42
•
Cruise Control Relay — This relay is installed
at the factory for use with the optional Cruise
Control Kit. The relay functions in the cruise
control circuit, when the kit is installed.
•
•
Note the position of the two harness leads, then
disconnect the leads and replace the faulty
relay with a new relay. Secure the relay to the
wire harness with electrical tape.
Position the wire harness in the dash panel and
reinstall the dash panel insert.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
CHECKING TRANSMISSION/HYDRAULIC
SYSTEM OIL LEVEL
Check the hydro transmission/hydraulic system oil
level before each use. NOTE: Check the oil level
only while the engine is stopped and the tractor is
standing on a level surface.
The oil level sight glass is located in the rear of the
transmission housing, just to the right of the rear
PTO shaft. Refer to Figure 43.
The oil level is okay if oil can be seen through the
sight glass. If the level is below the sight glass, oil
must be added to the transmission as follows:
25 Hour Break-In Period Filter Change
During the initial hours of tractor operation, contam-
inants caused by the normal break-in of internal
transmission and hydraulic system components will
collect in the oil filters. Because of this, both the
hydro transmission and hydraulic system filters
should be changed after the first 25 hours of
operation.
Hydro Pump Filter — Part No. BS-492932S
Hydraulic System Filter — Part No. 723-3014
NOTE: If a front end loader, or a loader and back-
hoe, is installed on the tractor after the first 25
hours of operation, it is recommended that the fil-
ters again be changed after the first 25 hours of
operation with these attachments installed.
•
Locate the oil fill plug on the upper right of the
rear of the transmission housing. See Figure 43.
OIL FILL PLUG
Changing Hydro Transmission Oil Filter
The hydro transmission oil filter should be changed
after the first 25 of tractor operation, and after every
100 hours operation.
•
Stop the tractor engine and lower the mower
deck or any other hydraulically lifted implement
to the ground.
OIL LEVEL
SIGHT
•
•
Slide the seat fully forward; then tilt seat forward.
HOLE
Through the access hole in the rear fender,
clean the area around the hydro transmission
oil filter to prevent debris from entering the
hydraulic system. Refer to Figure 44.
Figure 43
•
•
•
Clean the area around the oil fill plug to prevent
debris from entering the transmission housing.
•
Stuff shop rags underneath the hydro transmis-
sion filter to absorb any lost oil when the filter is
removed. See Figure 44.
Turn the oil fill plug counterclockwise to unscrew
from the transmission housing.
Insert a funnel (preferably one with a flexible
spout) into the fill hole of the transmission
housing.
HYDRO
•
Add Cub Cadet Drive System Plus oil until the
oil level can be seen through the sight glass.
Do not overfill the transmission.
TRANSMISSION
ACCESS HOLE
FILTER
IN FENDER
IMPORTANT: Always use Cub Cadet Drive
System Plus oil to ensure correct formulation.
Substitute oils could affect performance and
may cause damage to the transmission.
Seat Removed
for Clarity
•
Reinsert the oil fill plug into the transmission
housing and turn clockwise until tight.
CHANGING THE HYDRO TRANSMISSION AND
HYDRAULIC SYSTEM OIL FILTERS
With the exception of the first oil filter change after
the 25 hour break-in period, the hydraulic system oil
filter should be changed along with the trans-
mission/hydraulic system oil after every 200 hours
of operation. The hydro transmission filter should
be changed after every 100 hours of operation.
Figure 44
•
Apply a light coating of clean transmission oil to
the gasket of the new hydro transmission filter.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Remove the old hydrostatic filter by turning it
counterclockwise, and immediately replace with
the new filter. Turn the filter clockwise by hand
until the gasket contacts the filter base; then
tighten the filter an additional 1/2 to 3/4 turn.
changing the hydraulic system oil filter. If collected
in a clean container and kept free of debris, this
oil may be reused in the transmission/hydraulic
system. Install the new filter as quickly as possible
to minimize any loss of oil from the transmission.
Clean any residual oil from the top of the
transmission.
•
•
Apply a light coating of clean transmission oil to
the gasket of the new hydraulic system oil filter.
Changing Hydraulic System Filter
From beneath the tractor frame, remove the old
hydraulic system filter by turning it counter-
clockwise.
The hydraulic system oil filter should be changed
after the first 25 of tractor operation, and after every
200 hours operation.
•
•
When performing the 200 hour filter change,
clean the oil filter adapter.
•
Stop the tractor engine and lower the mower
deck or any other hydraulically lifted implement
to the ground. NOTE: To improve access to the
hydraulic system filter, the mower deck should
be removed from the tractor.
The hydraulic system oil filter is either mounted
horizontally on the front of the transmission
housing, or is remotely mounted in the vertical
position between the tractor frame rails. Refer
to Figure 45.
Install the new filter. Turn the filter clockwise,
by hand, until the gasket contacts the surface
of the filter adapter; then tighten the filter an
additional 1/2 to 3/4 turn.
•
•
•
Clean area around the transmission oil fill plug
to prevent debris from entering the transmis-
sion (Refer to Figure 43) and remove the plug.
Following the instructions previously provided
in CHECKING TRANSMISSION/HYDRAULIC
SYSTEM OIL LEVEL, refill the transmission
with the clean salvaged oil or with new hydrau-
lic oil.
•
•
Clean the area around the oil filter to prevent
debris from entering the system.
Position a suitable container below the hydrau-
lic system filter. Refer to Figure 45.
•
•
Reinsert the oil fill plug into the transmission
housing and turn clockwise until tight.
Start the engine and allow it to run for a few
minutes. Shut the engine off, then check for
leaks and recheck the oil level in the transmis-
sion housing.
CHANGING THE HYDRO TRANSMISSION AND
HYDRAULIC SYSTEM OIL
Change the hydrostatic transmission/hydraulic
system oil after every 200 hours of operation. The
dry capacity of the transmission/hydraulic system is
approximately 20 quarts.
TRANS. MOUNTED
HYDRAULIC SYSTEM
OIL FILTER
TRANSMISSION
DRAIN PLUG
Change the transmission/hydraulic system oil as
follows:
•
Operate the tractor for a short period to warm
the oil to the normal operating temperature.
Place the tractor on a level surface and engage
the parking brake.
•
Stop the tractor engine and lower the mower
deck or any other hydraulically lifted implement
to the ground. NOTE: To improve access to the
drain plug and hydraulic system filter, the
mower deck should be removed from the
tractor.
REMOTE MOUNTED
HYDRAULIC SYSTEM
OIL FILTER
Figure 45
•
Clean the area around the transmission drain
plug and the oil fill plug to prevent debris from
entering the transmission. Refer to Figure 43
and Figure 45.
NOTE (25 Hour Break-In Filter Change Only):
When performing the 25 hour break-in filter change,
some oil may drain from the transmission when
34
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Place a suitable container(s) beneath the front
of the transmission housing.
Remove the oil fill plug to help vent the trans-
mission, then remove the drain plug and allow
the transmission oil to drain into the con-
tainer(s). Reinstall the drain plug after draining
the oil. Refer to Figure 43 and Figure 45.
WHEEL HUB
LUBE FITTING
STEERING
KNUCKLE
LUBE FITTING
Dispose of used oil in an environmentally
safe manner. If necessary, contact your
area EPA office for proper disposal proce-
dures and recycling center locations.
•
Change the hydro transmission filter as
instructed in Changing Hydro Transmission
Oil Filter.
PIVOT PIN
LUBE FITTING
Figure 46
•
•
Change the hydraulic system filter as instructed
in Changing Hydraulic System Oil Filter.
WHEEL LUG NUT TORQUE
Insert a funnel (preferably one with a flexible
spout) into the fill hole in the rear of the trans-
mission housing.
The front wheel bolts and rear lug nuts should be
retorqued after the first ten hours of operation and
every 100 hours thereafter, or if the wheel assembly
has been removed. Using a torque wrench, retighten
the lug bolts and lug nuts as follows:
•
Pour Cub Cadet Drive System Plus oil into the
transmission housing until the oil level can be
seen through the sight glass. Do not overfill the
transmission.
Rear Wheels—In a staggered pattern, retorque the
rear wheel lug nuts to 60-70 ft. lbs.
IMPORTANT: Always use Cub Cadet Drive
System Plus oil to ensure correct formulation.
Substitute oils could affect performance and
may cause damage to the transmission.
Front Wheels—In a staggered pattern, retorque
the front wheel lug bolts to 60-70 ft. lbs.
TIRE MAINTENANCE
Check the tire air pressure after every 50 hours of
operation or weekly. Keep the tires inflated to the
recommended pressures. Improper inflation will
shorten the service life of a tire. See the tire side
wall, or the Tire Inflation chart, for proper inflation
pressures. Observe the following guidelines:
•
Reinsert the oil fill plug into the transmission
housing and turn clockwise until tight.
•
Start the engine and allow it to run for a few
minutes. Shut the engine off, then check for
leaks and recheck the oil level in the
transmission housing.
•
Do not inflate a tire above the maximum
pressure shown either on the sidewall of the
tire or the Tire Inflation chart.
LUBRICATION OF DRIVE SHAFT
Lubricate both ends of the drive shaft after every 50
hours of operation as follows:
•
Do not reinflate a tire that has been run flat or
seriously under inflated. Have a qualified tire
mechanic inspect and service the tire.
•
The front end of the drive shaft can be
accessed from under the hood, and the rear
end from beneath the tractor. NOTE: It may be
necessary to rotate the drive shaft to access
the grease fittings.
WARNING: Servicing tires can be dan-
gerous. Whenever possible, trained
personnel should service and mount
tires.
•
Using a pressure lubricating gun, lubricate the
drive shaft with Cub Cadet 251H EP grease.
If you must service the tires, observe the following
safety precautions to avoid an injury or fatality:
LUBRICATION OF FRONT AXLE
Lubricate the front axle pivot pin, steering knuckles,
and wheel hubs after every 10 hours of operation.
See Figure 46. Using a pressure lubricating gun,
lubricate the drive shaft with Cub Cadet 251H EP
grease.
•
•
Make certain the rim is clean and free of rust.
Lubricate the flanges of the rim and beads of
the tire with soap solution.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: When seating the beads,
never inflate a tire over 35 PSI. Inflat-
ing a tire with unseated beads beyond
35 PSI could break the bead or rim with
sufficient explosive force to cause a
serious injury.
If the ROPS is removed for any reason, make sure
the proper hardware is used to reinstall it, and that
the recommended torque values are applied to the
fasteners.
When replacing or reinstalling the ROPS, apply
Loctite® 242 to the threads of the bolts and torque
the bolts to 60 to 70 ft. lbs.
•
•
Inflate the tire to seat the beads. If the tire
beads have not seated at or before 35 PSI,
allow the tire to deflate. Reposition the tire on
the rim, lubricate the tire beads and rim flanges,
and reinflate until seated - up to a maximum of
35 PSI.
TRACTOR STORAGE
If your tractor is not going to be operated for an
extended period of time (thirty days to approxi-
mately six months), the tractor should be prepared
for storage. Store the tractor in a dry and protected
location. If stored outside, cover the tractor (includ-
ing the tires) to protect it from the elements. The
procedures outlined below should be performed
whenever the tractor is placed in storage.
After the beads have seated, adjust the infla-
tion pressure to the recommended operating
pressure.
•
•
Do not use a damaged rim, or attempt to repair
a rim by brazing, welding, or pounding out.
Make certain the jack used to raise the tractor
has a weight capacity adequate for lifting the
tractor.
1. Change the engine oil and filter following the
instructions provided in CHANGING THE
ENGINE OIL AND FILTER in SECTION 5.
•
•
Place the tractor on a firm, level surface and
position jack stands to support the raised
tractor while repairing tires.
WARNING: Never store the tractor with
fuel in the tank indoors or in poorly
ventilated enclosures, where fuel
fumes may reach an open flame, spark
or pilot light as on a furnace, water
heater, clothes dryer, etc.
DO NOT place any part of your body beneath
the tractor or start the tractor engine while the
tractor is raised off the ground with a jack.
WARNING: Fuel left in the fuel tank
deteriorates and will cause serious
starting problems.
TIRE INFLATION CHART
Tread
Type
Turf
Inflation
Pressure
15 psi
Position
Front
Tire Size
18 x 8.5-8
26 x 12-12
Rear
Turf
10 psi
2. If storing the tractor for 30 days or more:
To prevent gum deposits from forming inside
the engine’s carburetor and causing possible
malfunction of the engine, the fuel system must
be either completely emptied, or the gasoline
must be treated with a stabilizer to prevent
deterioration.
MAINTENANCE OF THE ROLLOVER
PROTECTIVE STRUCTURE (ROPS)
Periodically (at least every six months) visually
inspect the ROPS for damage and loose fasteners.
If damage is noted, contact your Cub Cadet dealer.
Using a fuel stabilizer:
If an accident has occurred which may have
damaged the ROPS, have the ROPS thoroughly
inspected by your Cub Cadet dealer.
• Read the product manufacturer’s instructions
and recommendations.
• Add to clean, fresh gasoline the correct
amount of stabilizer for the capacity
(approximately 6 gallons) of the fuel system.
WARNING: To ensure the structural
integrity of the ROPS to provide opera-
tor protection, do not attempt to
straighten or weld the ROPS. A dam-
aged ROPS should be replaced.
• Fill the fuel tank with treated fuel and run the
engine for 2-3 minutes to get stabilized fuel
into the carburetor.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Emptying the fuel system:
5. Lubricate all lubrication points.
• Prior to putting the tractor in storage, monitor
fuel consumption with the goal of running the
fuel tank empty.
6. Jack up and block the tractor to remove the
weight from the tires if stored for a long period.
If not blocked up, reinflate the tires regularly.
• If a large volume of fuel is left-over, the fuel
line can be disconnected at the fuel filter and
the leftover fuel drained into an approved
container.
NOTE: We do not recommend the use of a
pressure washer or garden hose to clean your
tractor. They may cause damage to electrical
components; spindles; pulleys; bearings; or the
engine. The use of water will result in shortened life
and reduce serviceability.
• Run the engine until it begins to stall. Use the
choke to keep the engine running until all fuel
in the carburetor has been exhausted.
3. Clean the engine and the entire tractor
thoroughly.
REMOVING THE TRACTOR FROM STORAGE
•
•
Check the engine oil.
4. Fully charge the battery, then disconnect the
negative cable at the battery to prevent possi-
ble discharge. Recharge the battery periodically
when in storage.
Fully charge the battery and inflate the tires to
the recommended pressure.
•
•
Start the engine and allow to idle for a few
minutes to ensure engine is operating properly.
NOTE: Remove the battery if exposed to prolonged
periods of sub-freezing temperatures. Store in a
cool, dry location where temperatures are above
freezing.
Drive the tractor without a load to make certain
all the tractor systems are functioning properly.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5: ENGINE INFORMATION AND MAINTENANCE
KOHLER CO.
FEDERAL AND CALIFORNIA EMISSION CONTROL SYSTEMS
LIMITED WARRANTY
SMALL OFF-ROAD EQUIPMENT ENGINES
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Kohler Co. are pleased to explain the Federal and
California Emission Control Systems Warranty on your small off-road equipment engine. For California, engines produced in 1995 and later must be
designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, 1997 and later model year engines must be designed,
built and equipped, to meet the U.S. EPA regulations for small non-road engines. The engine must be free from defects in materials and workmanship
which cause it to fail to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser. Kohler Co.
must warrant the emission control system on the engine for the period of time listed above, provided there has been no abuse, neglect or improper main-
tenance.
The emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and catalytic converter. Also included
are the hoses, belts and connectors and other emission related assemblies.
Where a warrantable condition exists, Kohler Co. will repair the engine at no cost, including diagnosis (if the diagnostic work is performed at an autho-
rized dealer), parts and labor.
MANUFACTURER’S WARRANTY COVERAGE
Engines produced in 1995 or later are warranted for two years in California. In other states, 1997 and later model year engines are warranted for two
years. If any emission related part on the engine is defective, the part will be repaired or replaced by Kohler Co. free of charge.
OWNER’S WARRANTY RESPONSIBILITIES
(a) The engine owner is responsible for the performance of the required maintenance listed in the owner’s manual. Kohler Co. recommends that you
retain all receipts covering maintenance on the engine, but Kohler Co. cannot deny warranty solely for the lack of receipts or for your failure to
assure that all scheduled maintenance was performed.
(b) Be aware, however, that Kohler Co. may deny warranty coverage if the engine or a part has failed due to abuse, neglect, improper maintenance or
unapproved modifications.
(c) For warranty repairs, the engine must be presented to a Kohler Co. service center as soon as a problem exists. Call 1-800-544-2444, or access our
amount of time, not to exceed 30 days.
If you have any questions regarding warranty rights and responsibilities, you should contact Kohler Co. at 1-920-457-4441 and ask for an Engine Service
representative.
COVERAGE
Kohler Co. warrants to the ultimate purchaser and each subsequent purchaser that the engine will be designed, built and equipped, at the time of sale, to
meet all applicable regulations. Kohler Co. also warrants to the initial purchaser and each subsequent purchaser, that the engine is free from defects in
material and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years.
Engines produced in 1995 or later are warranted for to years in California. For 1997 and later model years, EPA requires manufacturers to warrant
engines for two years in all other states. These warranty periods will be begin on the date the engine is purchased by the initial purchaser. If any emission
related part on the engine is defective, the part will be replaced by Kohler Co. at no cost to the owner. Kohler Co. is liable for damages to other engine
components caused by the failure of a warranted part still under warranty.
Kohler Co. shall remedy warranty defects at any authorized Kohler Co. engine dealer or warranty station. Warranty repair work done at an authorized
dealer or warranty station shall be free of charge to the owner if such work determines that a warranted part is defective.
Listed below are the parts covered by the Federal and California Emission Control Systems Warranty. Some parts listed below may require scheduled
maintenance and are warranted up to the first scheduled replacement point for that part. The warranted parts are:
•
•
•
•
•
•
Carburetor assembly
•
•
•
•
•
•
Ignition module(s) with high tension lead
Spark advance module (if equipped)
Oxygen, speed, throttle position, and temperature sensors (if equipped)
Electronic control unit (if equipped)
Fuel injectors (EFI system - if equipped)
Air filter, fuel filter, and spark plugs (only to first scheduled replacement
point)
Throttle body (EFI system - if equipped)
Catalytic muffler (if equipped)
Fuel metering valve (if equipped)
Crankcase breather
Fuel pressure regulator (EFI system - if equipped)
LIMITATIONS
This Emission Control System Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, improper maintenance, repairs improperly performed or replacement not conforming
to Kohler Co. specifications that adversely affect performance and/or durability and alterations or modifications not recommended or approved in
writing by Kohler Co.,
(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement point,
(c) consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.,
(d) diagnosis and inspection fees that do not result in eligible warranty service being performed, and
(e) any add-on or modified part, or malfunction of authorized parts due to the use of add-on or modified parts.
MAINTENANCE AND REPAIRS REQUIREMENTS
The owner is responsible for the proper use and maintenance of the engine. Kohler Co. recommends that all receipts and records covering the perfor-
mance of regular maintenance be retained in case questions arise. If the engine is resold during the warranty period, the maintenance records should be
transferred to each subsequent owner. Kohler Co. reserves the right to deny warranty coverage if the engine has not been properly maintained; however,
Kohler Co. may not deny warranty repairs solely because of the lack of repair maintenance or failure to keep maintenance records.
Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repair establishment or individual; how-
ever, warranty repair must be performed by a Kohler authorized service center. Any replacement part or service that is equivalent in performance
and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
ENGINE MAINTENANCE
WARNING: Use care when servicing
•
•
If recently operated, allow the engine to cool
and the oil to drain back into the oil pan.
To check the oil level, withdraw the dipstick and
wipe it clean; then insert the dipstick all the way
into the tube before withdrawing it for a true
reading. See Figure 47.
any component in the engine area. If
the engine has recently been operated,
components will be hot and could
cause burns. Allow the engine to cool
before servicing.
•
•
Always keep the oil level between the ‘F’ (full)
and the ‘L’ (add) marks on the dipstick. See
Figure 48.
WARNING: Before servicing the engine,
place the tractor on a level surface,
stop the engine, engage the parking
brake, and remove the key from the
ignition switch. For additional safety,
remove the spark plugs to prevent
accidental starting.
Reinsert the dipstick into the dipstick tube and
push firmly into the tube.
F
Full
Operating
Range
CLEANING THE ENGINE
Add
L
This tractor has an air-cooled engine. Air must be
able to circulate freely over the cooling fins of the
cylinders and cylinder heads. Keep the area
between the engine baffles and cylinders free of
accumulated dirt and debris to prevent engine over-
heating, which could possibly cause extensive
engine damage.
Figure 48
ADDING ENGINE OIL
WARNING: Never overfill the engine
crankcase. The engine may overheat
and/or damage may result if the
crankcase is below the “ADD” mark or
over the “FULL” mark on the dipstick.
For best results, fill to the “FULL” mark
on the dipstick as opposed to adding a
given quantity of oil. Always check the
level on the dipstick before adding
more oil.
WARNING: Keep the muffler area clean.
Before running the engine, remove all
combustible debris from the muffler area.
CHECKING ENGINE OIL LEVEL
Before each use, the oil level in the engine crank-
case should be checked to see that it is filled to the
correct level. Close monitoring of engine oil level
during the first 10 hours of operation is especially
important. The oil level should be checked hourly
during the first 10 hours of operation.
Refer to the LUBRICATION TABLE in the MAINTE-
NANCE SECTION of this manual to determine the
proper type of oil to add to the crankcase for the
conditions under which the engine will be operated.
•
Check the oil level only while the engine is
stopped and the tractor is level. Clean the area
around the oil level dipstick to prevent debris
from entering the crankcase. See Figure 47.
•
Place the tractor on a level surface and engage
the parking brake. Stop the tractor engine and
remove the ignition key.
•
Clean the area around the oil filler cap to
prevent debris from entering the crankcase.
Refer to Figure 47.
DIPSTICK
OIL FILL CAP
•
•
Turn the oil filler cap a quarter turn counter-
clockwise to remove from the right valve cover.
SLOWLY pour oil into the crankcase until the
oil level reaches the “FULL” mark on the
dipstick. Refer to Figure 48.
•
Insert the oil fill cap into the valve cover and
turn clockwise until fully tightened. Reinsert the
dipstick into the dipstick tube and push firmly
into the tube.
IMPORTANT: The oil fill cap and dipstick must
always be installed securely in place when the
engine is running. Severe engine damage could
result from failure to do so.
DIPSTICK TUBE
VALVE COVER
Figure 47
39
Download from Www.Somanuals.com. All Manuals Search And Download.
CHANGING THE ENGINE OIL AND FILTER
•
Push the engine drain valve slightly inward;
then turn counterclockwise until it stops. Pull
the valve outward to open the valve and drain
the oil from the engine.
WARNING: Because the engine is run
prior to draining the oil, the engine may
be hot. Use caution to avoid burning
yourself on engine surfaces.
•
•
Allow the old oil to completely drain from the
engine crankcase into the container below.
The engine oil and oil filter should be changed after
every 100 hours of operation. Refer to the LUBRI-
CATION TABLE in the MAINTENANCE SECTION
of this manual for the quantity of oil needed, and to
determine the proper type of oil to use for the condi-
tions under which the engine will be operated.
Remove the filter by turning it counterclockwise
using an automotive type filter wrench to
loosen. See Figure 49.
•
Push the drain valve fully inward until you are
able to turn the valve clockwise to lock in the
closed position. Refer to Figure 49.
Run the engine for a few minutes to allow the oil in
the crankcase to warm up. Warm oil will flow more
freely and carry away more engine impurities. Use
care to avoid burns from hot oil. While the engine
oil is warm, proceed as follows:
•
•
Clean any oil from the end of the drain valve
and push the cap onto the valve.
To assure a continuous flow of oil to all critical
lubrication points within the engine, pour some
new oil into the threaded center hole of the filter
and allow time for the oil to be absorbed into
the filter material.
•
Place the tractor on a level surface and engage
the parking brake. Stop the tractor engine and
remove the ignition key.
•
Clean around the base of the oil filter, the oil
filler cap, and the dipstick tube to prevent
debris from entering the crankcase.
•
Apply a light coating of clean oil on the gasket of
the new oil filter. Thread the filter on by hand
until the gasket contacts the filter mounting sur-
face, then tighten the filter an additional 2/3 to 1
turn.
•
•
Remove the dipstick and oil fill cap from the
engine. Refer to Figure 49.
Locate the engine drain valve on the rear of the
engine (See Figure 49). Place a suitable
container below the open end of the drain valve
to collect the old oil.
•
Refill the crankcase to the "FULL" mark on the
dipstick with the appropriate type oil.
•
•
Reinstall the oil fill cap and dipstick.
Start the engine and run for about 3 minutes.
Stop the engine and check for leaks at the oil
filter and drain valve.
OIL
DIPSTICK
OIL
FILL
CAP
•
Recheck the oil level and, if needed, add oil to
bring the oil level up to the "FULL" mark.
WARNING: Never overfill the engine
crankcase. The engine may overheat
and/or damage may result. For best
results, fill to the “FULL” mark on the
dipstick as opposed to adding a given
quantity of oil. Always check the level
on the dipstick before adding more oil.
Dispose of used oil in an environmentally
safe manner. If necessary, contact your
area EPA office for proper disposal
procedures and recycling center locations.
OIL
FILTER
ENGINE
DRAIN
VALVE
OIL
DRAIN
CAP
IMPORTANT: The oil fill cap and dipstick must
always be installed securely in place when the
engine is running. Severe engine damage could
result from failure to do so.
Figure 49
•
Pull the oil drain cap off the end of engine drain
valve. To prevent loss of the cap, do not
remove the cap’s retaining ring from the drain
valve. See Figure 49.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICING OIL COOLER - IF EQUIPPED
Inspect and clean the oil cooler, located next to the
oil filter, after every 100 hours of operation.
WARNING: Operating the engine with
loose or damaged air cleaner compo-
nents will allow unfiltered air into the
carburetor, causing extensive wear and
eventual failure of the engine.
Clean debris from the fins of the oil cooler with a
brush or using compressed air. See Figure 50.
SERVICING THE FOAM PRECLEANER
OIL COOLER
Wash the foam precleaner every 25 hours of
operation. Wash more often when operating under
extremely dusty conditions. Replace the precleaner
if torn or otherwise damaged.
Wash the precleaner as follows (Refer to Figure 51):
•
•
•
Loosen the cover retaining knob and lift off the
air cleaner cover.
Remove the foam precleaner by carefully
slipping it up off the paper element.
COOLER
FINS
Wash the precleaner in warm water with
detergent. Rinse the precleaner thoroughly to
remove all traces of the detergent. Squeeze out
(do not wring) excess water in a dry cloth. Allow
the precleaner to air dry.
Figure 50
CHECKING THE AIR CLEANER
Check the air cleaner daily or before starting the
engine. Check for loose or damaged components
and check the condition of the filter element.
Remove any buildup of dirt and debris in the air
cleaner cover.
•
•
•
Saturate the precleaner will clean engine oil,
then squeeze out all excess oil.
Carefully slip the precleaner fully onto the
paper element.
RETAINING
KNOB
AIR
CLEANER
COVER
Reinstall the air cleaner cover and secure with
the retainer knob.
SERVICING THE PAPER ELEMENT
Replace the paper air cleaner element after every
100 hours of operation. Replace the element more
often if operating the tractor under extremely dusty
conditions. Refer to Figure 51.
WING
NUT
ELEMENT
COVER
RUBBER
SEAL
•
Loosen the cover retaining knob and lift off the
air cleaner cover.
PAPER
ELEMENT
•
Remove the wing nut and lift off the element
cover. Lift out the paper air cleaner element
with precleaner.
FOAM
PRECLEANER
ELEMENT
•
•
Remove the foam precleaner by carefully
slipping it off the paper element.
AIR
CLEANER
BASE
AIR
CLEANER
STUD
Check the paper element for excessive dirt,
paper tears, or damage to the seal on the bot-
tom of the element. Replace a dirty or damaged
paper element. Do not use pressurized air to
clean the paper element.
•
When servicing the air cleaner, also inspect the
air cleaner base and the rubber seal for any
type of damage. Replace if damaged.
Figure 51
See Figure 51 for assembly of the air cleaner
elements.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Slip the precleaner fully onto the paper ele-
ment and reinstall the paper element onto the
air cleaner base.
.030 in. gap
•
•
Install the element cover and secure with the
wing nut.
Reinstall the air cleaner cover and secure with
the retainer knob.
IMPORTANT: Properly cleaned and installed
air cleaner elements significantly contribute to
prolonging engine life.
SERVICING THE SPARK PLUGS
Figure 52
WARNING: To avoid possible injury, be
sure the engine is off and has cooled
before making any adjustments or
repairs.
•
Reinstall the spark plugs and torque to 18 ft-
lbs. Connect the spark plug wires.
CHANGING THE FUEL FILTER
WARNING: Do not replace the fuel filter
Check the spark plugs after every 100 hours of
operation. Replace with new plugs if necessary.
See your authorized dealer for the correct
replacement spark plugs (Pt. No. 759-3336).
when tractor is hot. Allow the tractor to
cool before separating the fuel lines.
•
Disconnect the spark plug wires and remove all
dirt from around the spark plug before
removing.
The tractor is equipped with an in-line fuel filter. The
fuel filter can be accessed from underneath the
tractor along the left side of the tractor frame, just
forward of the fuel tank.
•
•
Use a spark plug wrench to remove spark plugs.
Clean carbon deposits from the electrodes
using a soft wire brush.
The fuel filter cannot be disassembled.
Consequently you must visually inspect the filter
periodically. Inspect for a build-up of residue inside
the filter body, and for a dirty element which can be
indicated by discoloration. Replace the fuel filter
when dirty.
•
•
Inspect for cracked porcelain or any other wear
or damage. Replace with a new spark plug if
necessary.
Check the gap of the spark plugs. The gap
must be .030 inch (0.76mm). Reset if
necessary.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6: MODELS WITH FACTORY INSTALLED 60" MOWER DECK
This section applies only to those models with the
factory equipped 60 inch mower deck. Skip this
section and refer to your mower deck Owner’s
Manual for all other models.
measurement for the left blade. If the two blade
heights are not within 1/16 inch, the deck must be
leveled. Note which blade had the larger
distance between the cutting edge and level
surface.
DECK LEVELING ADJUSTMENTS
The 60" mower deck is equipped with ground
following front caster wheels and is designed to be
operated with the front caster wheels and rear gauge
wheels on the ground. However, to ensure an even
cut on all types of terrain, the mower deck should be
properly leveled. To level the mower deck, proceed
as follows:
2
1
4
WARNING: Before leveling the mower
deck, position the tractor on a hard level
surface, engage the parking brake lever
and turn ignition key to the “OFF” posi-
tion. ALWAYS stop the engine after
utilizing the tractor hydraulic lift system.
When handling the mower deck, be care-
ful not to cut yourself on the sharp
blades.
3
1. Finger guard
2. Blade
3. Hard Level Surface
4. Measure This Distance
Figure 54
•
•
Move to the left side of the tractor, to the deck
check chain assembly. Loosen the jam nut on the
check chain. Refer to Figure 55.
Side To Side Leveling
NOTE: Check for proper tire inflation before checking
and/or making a leveling adjustment.
Depending on whether the left side of the deck
was higher or lower than the right side, turn the
hex shaft of the chain assembly as needed to
level the blades to within 1/16" of each other.
Turn the hex shaft to the right to shorten the
adjustment chain and raise the left side of the
deck. Turn the hex shaft to the left to lengthen the
chain and lower the left side of the deck. See
Figure 55.
When the deck is properly leveled, the left and right
blades will have corresponding cutting-edge-to-
ground measurements within 1/16 inch of each other.
•
Use the tractor hydraulic lift system to raise the
deck so that its wheels are off the ground. Stop
the engine.
•
Carefully rotate the outer cutting blades so that
they are positioned perpendicular to the tractor
frame. See Figure 53.
HEX JAM NUT
SHORTEN
LENGTHEN
HEX
CHECK
CHAIN
SHAFT
OUTER BLADES
PERPENDICULAR TO FRAME
Figure 55
Figure 53
•
Tighten the hex jam nut against the hex check
chain shaft. Refer to Figure 55.
•
Referring to Figure 54, measure and record the
distance from the level surface to the outer-most
cutting edge of the right blade. Repeat this
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Front To Back Leveling
The front to back pitch of the deck is normally
determined by the deck wheels when the deck is
operated as designed with its wheels on the ground.
However, the deck pitch should be checked to ensure
an even cut when mowing uneven terrain, or when
mowing with the deck wheels off the ground.
REAR
CUTTING
EDGE
FRONT
CUTTING
EDGE
B
A
When properly leveled, the pitch of the deck will result
in the front and rear cutting edges of the blades being
even, to a maximum of 1/4 inch lower in the front.
Figure 57
The front to back pitch of the deck was initially set
when adjustment of the deck hanger rod assembly
was completed during deck installation and should be
within specifications. Check and, if necessary, adjust
the pitch of the deck as follows:
•
•
If the measurements are not within this range, the
front to back leveling of the deck should be
adjusted as follows:
If the front of the deck is too low, the deck hanger
rod assembly must be shortened. From the front
of the tractor, evenly turn the hex lock nuts
clockwise to shorten the hanger rod assembly
and raise the front of the deck. See Figure 58.
NOTE: Check for proper tire inflation before checking
and/or making a leveling adjustment.
•
Use the tractor hydraulic lift system to raise the
deck so that its wheels are off the ground. Stop
the engine.
•
Carefully rotate the outer cutting blades so that
the ends of the blades point to the front and rear
of the deck. See Figure 56.
DECK HANGER
ROD ASSEMBLY
NOTE: If side to side leveling of the deck was
correctly performed, measuring only the right
blade should be adequate to check the front to
back leveling.
HEX LOCK NUT
Figure 58
•
If the front of the deck is too high, the deck
hanger rod assembly must be lengthened. From
the front of the tractor, evenly turn the hex lock
nuts counterclockwise to lengthen the hanger rod
assembly and lower the front of the deck. See
Figure 58.
CHUTE
RIGHT BLADE POINTING
DEFLECTOR
TO FRONT AND REAR
Figure 56
•
Accessing the right hand blade through the
discharge chute opening, measure the distance
from the front cutting edge to the ground
(measure A), and from the rear cutting edge to
the ground (measure B). The front edge of the
blade (measure A) should be between equal with
its back edge (measure B) and lower by a
maximum of 1/4 inch. See Figure 57.
NOTE: The front hanger rod must be against the front
of both slots in the deck front roller bracket. If one
side of the rod is not against the front of the slot after
attaining the correct front pitch to the deck, tighten the
front lock nut on that side until the rod just contacts
the front of the slot.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
SETTING THE CUTTING HEIGHT
•
Repeat the above steps for the caster wheel axle
on the other side of the deck. Make certain the
corresponding index hole setting is used in all
four hole sets.
The deck cutting height is set by positioning the left
and right caster wheel axles in one of the five index
hole settings of the deck height adjustment bracket.
The index hole settings range in 1/2 inch increments
from a cutting height of approximately 1-1/2 inches
(top hole) to 3-1/2 inches (bottom hole). If a higher
cutting height is desired, the deck will have to be
suspended from the tractor’s lift system. Use the
system’s lift lever to set the deck cutting height. The
caster wheels will not contact the ground.
REMOVAL OF DECK
Place the tractor and mower deck on a firm and level
surface with enough room to slide the deck out from
under the right side of the tractor.
WARNING: Before removing the mower
deck, engage the parking brake lever and
turn ignition key to the “OFF” position.
ALWAYS stop the engine after utilizing
the tractor hydraulic lift system. When
handling the mower deck, be careful not
to cut yourself on the sharp blades.
Refer to Figure 59 and adjust the deck cutting height
as follows:
WARNING: Use caution adjusting the
deck height if the deck’s weight is not
supported by the tractor lift system.
Removal of the fasteners securing the
caster wheel axles could allow the deck
to drop and may result in minor injury.
•
•
Check that the deck is in the lower cutting height
position. If it is not, raise the deck, remove the
hex lock nuts and carriage bolts, and reposition
the caster wheel axles in the lower cutting height
position (Refer to Figure 59). Lower the deck to
the ground and stop the engine.
•
•
Use the tractor lift system to raise the mower
deck off the ground.
Working from either the left or right hand side of
the deck, support the caster wheel axle and
remove the two carriage bolts and hex lock nuts.
See Figure 59.
Compress the locking collar and disconnect the
deck drive shaft from the tractor PTO shaft (See
Figure 60). Pivot the drive shaft to the side as far
as possible.
•
Align the caster wheel axle with two
corresponding lower index holes to raise the
cutting height, or corresponding upper holes to
lower the cutting height. See Figure 59.
PTO SHAFT
HEX
DECK HGT.
CASTER
LOCK
ADJUSTMENT
WHEEL AXLE
NUTS
BRACKET
DRIVE
SHAFT
LOCKING COLLAR
CARRIAGE
BOLTS
Figure 60
LOWEST
•
Disconnect the check chain from the LH lift arm
by removing the internal cotter pin and clevis pin.
Reinstall the clevis pin and internal cotter pin in
the check chain to avoid their loss. Refer to
Figure 61.
CUTTING HEIGHT
HIGHEST
CUTTING HEIGHT
Figure 59
•
Insert the two carriage bolts and secure with the
hex lock nuts.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
INTERNAL
LH FRAME
MTG. PLATE
COTTER PIN
DECK
LIFT
ARM
CLEVIS PIN
CHECK
CHAIN
LH LIFT ARM
SIDE
BRACE
KLIK PIN
LOCKING RING
Figure 63
Figure 61
•
Roll the deck forward to disengage the deck
hanger rod from the slots of the deck front roller
bracket. Lift the deck hanger rod and slide out of
the slots in the front receiver brackets. See
Figure 64. Store the deck hanger rod assembly
with the deck to avoid misplacing it.
•
Disconnect the fixed link from the RH lift arm by
removing the internal cotter pin and clevis pin.
Reinstall the clevis pin and internal cotter pin in
the fixed link to avoid their loss. See Figure 62.
INTERNAL
COTTER PIN
DECK HANGER
ROD ASSEMBLY
CLEVIS PIN
DECK ROLLER
BRACKET SLOTS
RH LIFT
ARM
FIXED LINK
FRONT RECEIVER
BRACKET SLOTS
Figure 62
Figure 64
•
On each side of the tractor, flip the klik pin locking
ring upward and remove the klik pin from the
frame mounting plate pin. Slide the side brace
and deck lift arms from each frame mounting pin.
Reinstall the klik pins to avoid losing. Refer to
Figure 63.
•
Remove the internal cotter pins and clevis pins to
allow the rear deck wheels to pivot. See Figure
65.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
•
From either side of the tractor, lift the deck
hanger rod and roll the deck forward until the
hanger rod aligns with slots of the deck front
roller bracket. Lower the hanger rod into the front
roller bracket slots and slide the deck rearward
to engage the rod fully forward in the slots of the
roller bracket. Refer to Figure 64.
INTERNAL
COTTER PIN
•
•
If installed, remove the two klik pins from the pins
of LH and RH frame mounting plates.
Slide the deck lift arms and side braces onto the
pins of the LH and RH frame mounting plates.
Insert a klik pin through the hole of each frame
mounting plate pin. Flip the locking rings
downward and over the ends of the mounting
plate pins to lock the klik pins in place. Refer to
Figure 63.
REAR
DECK
WHEEL
CLEVIS PIN
Figure 65
NOTE: If necessary, start the engine and use the
tractor’s hydraulic lift lever to lower the lift arms on the
tractor. Stop the engine.
•
•
From the right side of the tractor, grasp the fixed
link and make certain it is clear of the right lift
arm. Refer to Figure 62.
•
Slide the fixed link of the deck over the RH lift
arm. Align the holes, insert the clevis pin, and
secure with the internal cotter pin (Refer to Figure
62).
Holding the fixed link upward, maneuver the fixed
link between the tire and fender while sliding the
deck out from beneath the right side of the
tractor.
•
Slide the check chain of the deck over the LH lift
arm. Align the holes, insert the clevis pin, and
secure with the internal cotter pin. Refer to Figure
61.
•
Reposition the rear deck wheels and reinstall the
clevis pins and internal cotter pins.
NOTE: When connecting the fixed link and check
chain, it is recommended that the clevis pins be
inserted from the inside-out to minimize the possibility
of contact with the brake rods and to ease installation
of the internal cotter pins.
INSTALLING THE DECK
•
Remove the internal cotter pins and clevis pins to
allow the rear deck wheels to pivot. Refer to
Figure 65.
•
Hold the fixed link upward and maneuver the
fixed link between the tire and fender while sliding
the deck underneath the right side of the tractor.
•
Compress the locking collar of the drive shaft and
slide the drive shaft fully onto the PTO shaft
protruding from the front of the transmission
housing. Release the collar and check to ensure
the drive shaft is locked onto the PTO shaft.
Refer to Figure 60.
•
•
Reposition the rear deck wheels and reinstall the
clevis pins and internal cotter pins.
While noting the forms (bends) in the rod are
correctly positioned, slide the deck hanger rod
into the slots in the front receiver brackets. Refer
to Figure 64.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
DECK MAINTENANCE
Once a month remove the hex cap screws and belt
covers to remove any accumulation of grass clip-
pings from around the spindle pulleys and V-belt.
Clean more often when mowing tall, dry grass.
Cleaning And Blade Care
Use the Deck Wash System as follows:
WARNING: When using the deck wash,
never engage the deck from any position
other than the operator’s seat of the trac-
tor. Do not use an assistant or engage
deck in the presence of bystanders.
The cutting blades must be kept sharp at all times.
Sharpen the cutting edges of the blades evenly so
that the blades remain balanced and the same angle
of sharpness is maintained. If the cutting edge of a
blade has been sharpened to within 5/8 inch of the
wind wing radius (See Figure 67), new blades must
be installed.
•
•
Attach the nozzle adapter to a standard garden
hose connected to a water supply.
Move the tractor to an area within reach of the
hose where the dispersal of wet grass clippings is
not objectionable to you. Disengage the PTO,
engage the parking brake, and stop the engine.
WIND
WING
5/8" FROM
RADIUS
•
Pull back the lock collar of the nozzle adapter and
push the adapter onto the deck wash nozzle at the
left end of the mower deck. Release the lock collar
to lock the adapter on the nozzle. See Figure 66.
Figure 67
When removing the blades, use a 1-1/8 inch wrench
to hold the head of the spindle bolt while loosening
the hex nut securing the blade.
Nozzle
Adapter
A block of wood may be placed between the deck
housing and the cutting edge of the blade to assist in
removal of the hex nut. See Figure 68.
Pull Lock
Collar Back
Adapter
Lock Collar
HEX NUT
Deck Wash
Nozzle
Figure 66
•
•
Turn on the water supply.
From the tractor operator’s seat, start the engine
and engage the PTO. Allow deck to run as
needed. Disengage the PTO and stop the engine.
WOOD BLOCK
IN POSITION
1-1/8" WRENCH
Figure 68
•
•
Turn off the water supply.
Pull back the lock collar of the nozzle adapter to
disconnect the adapter from the nozzle.
•
Repeat the previous steps to clean the deck
using the nozzle at the other end of the deck.
When reinstalling the blades, be sure they are
installed so that the wind wings are pointing upward
toward the top of the deck. Tighten the nuts to 90 to
110 ft-lbs. (122 to 149 N·m).
WARNING: Before performing any main-
tenance, place the PTO switch in the
“OFF” position, engage the parking
brake lever, turn the ignition key to the
“OFF” position and remove the key from
the switch. When servicing the mower
deck, be careful not to cut yourself on
the sharpened blades.
After replacing the blades, apply grease to the
exposed threads at the bottom of the spindles to
prevent rust buildup.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
5
4
6
3&4
2
3&4
1
2
1
6
1. Spindle Belt Covers
2. Hex Cap Screws
3. Button Plugs - Access to Spindle
Lube Fitting
4. Spindle Assembly Lube Fittings
5. Idler Arm Lube Fitting
6. Height Adjustment Brackets
Figure 69
SPINDLE BELT REPLACEMENT
•
Push the movable flat idler pulley (2, Figure 70)
toward the left side of the deck to relieve tension
from the belt. Slip the spindle belt off the movable
flat idler pulley, then carefully release the flat idler
pulley.
A worn spindle belt will affect the quality of cut from
the mower deck and should be replaced. Referring to
Figure 69 and Figure 70, replace the spindle belt as
follows:
•
•
•
•
•
Slide the belt off and over the LH spindle pulley,
then pull the belt under the LH belt cover
mounting strap. Refer to Figure 70.
Remove Spindle Belt
•
Remove the hex cap screws securing the LH belt
cover to the deck. Slide the belt cover tabs from
the slots of the deck height adjustment brackets
to remove the cover (See Figure 69).
Slip the belt off the fixed flat idler pulley, center
spindle pulley, and RH spindle pulley (Refer to
Figure 70).
•
•
Remove the three hex cap screws securing the
RH belt cover and remove the belt cover.
Remove the four hex cap screws and hex flange
lock nuts securing the gear box mounting bracket
to the deck mounting plate. Refer to Figure 70.
Observe the routing of the spindle belt to help
ensure proper installation of the new belt.
Lift the gear box/mounting bracket assembly and
slip the belt off and underneath the drive pulley.
Refer to Figure 70.
WARNING: The idler arm and movable
flat idler pulley (Refer to Figure 70) are
under spring tension. To prevent possi-
ble injury, use caution when handling the
idler pulley.
Remove the belt from the deck.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
1
5
4
8
1
6
2
1
1. Spindle Pulleys
2. Movable Flat Idler Pulley
3. Drive Pulley
4. Fixed Flat Idler Pulley
5. Spindle Belt
3
9
7
9
10
6. LH Belt Cover Mntg. Strap
7. Gear Box Mntg. Bracket
8. Idler Arm
9. Hex Cap Screws
10. Deck Mounting Plate
Figure 70
5. Route the belt as follows:
Install New Spindle Belt
•
•
•
•
around the left spindle pulley
1. Lift the gear box/mounting bracket assembly to
install the belt around the rear of the drive pulley
and through the center opening of the mounting
bracket.
around the rear of the fixed flat idler pulley
around the front of the center spindle pulley
to the right spindle pulley
2. Position the gear box mounting bracket on the
deck mounting plate and secure with the four hex
cap screws and hex flange lock nuts.
6. After making certain the spindle belt is properly
engaged in each pulley, pivot the movable flat idler
pulley toward the left side of the deck to relieve
tension and to allow the belt to be rolled onto the
right hand spindle pulley.
3. Route the backside of the belt around the
movable flat idler pulley. See Figure 70.
4. Loop the belt and slide it underneath the LH belt
cover mounting strap. See Figure 70.
7. Install the belt covers and secure with the hex cap
screws.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
MOWER DECK LUBRICATION GUIDE
Lubricant is cheap. Use plenty of it. Worn parts can
be expensive to replace.
NOTE: We do not recommend the use of a pressure
washer or garden hose to clean your unit. They may
cause damage to spindles; pulleys; or bearings. The
use of water will result in shortened life and reduce
serviceability.
Keep your supply of lubricating oil and grease stored
in clean containers, and covered to protect from dust
and dirt.
Keep the lubricating gun nozzle clean and wipe dirt
from the grease fittings before lubricating.
The life of any machine depends upon the care it is
given. Proper lubrication is a very important part of
that care.
The symbols in the illustrations indicate the method of
application and the hourly intervals to apply the
lubricant.
Be certain that all lubrication fittings are assembled in
place, using the lubrication illustration as a guide.
Use a pressure lubricating gun
and apply 251H EP grease (or
equivalent No. 2 multi-purpose
lithium grease) sufficient to flush
out the old grease and dirt.
Lubricate at the hourly intervals
indicated on the symbols.
Always lubricate the deck thoroughly before taking it
to the field. Use a pressure lubricating gun.
Be sure all fittings are free from dirt and paint so the
lubricant is certain to enter the bearing.
Miscellaneous working parts not provided with
lubrication fittings should be oiled daily with a good
grade of lubricating oil.
5
2
1
1
5
4
50
10
10
4
10
50
50
50
4
50
50
1. Deck Spindles — Every 10 Hours of Operation
2. Idler Arm — Every 10 Hours of Operation
3. Drive Shaft — Every 50 Hours of Operation
4. Caster Wheels — Every 50 Hours of Operation
5. Front Caster Spindles — Every 50 Hours of
Operation
4
50
3
Figure 71
51
Download from Www.Somanuals.com. All Manuals Search And Download.
MOWING
The following practices will help eliminate streaking:
•
•
•
•
Mow the area more often so the grass doesn’t get
too tall and heavy.
Operate the tractor at the recommended RPM
and at a slower forward speed.
WARNING: To avoid possible injury,
never direct the discharge of material
toward bystanders or allow anyone near
the machine while in operation. Although
the area has been supposedly cleared of
foreign objects, small objects may be
picked up and discharged by the mower.
Keep the blades sharp and replace the blades
when worn.
Follow the mowing pattern shown in Figure 72.
For best results it is recommended that the first two
laps should be cut with the discharge thrown towards
the center. After the first two laps, reverse the
direction to throw the discharge to the outside for the
balance of cutting. This will give a better appearance
to the lawn.
Do not cut the grass too short. Short grass invites
weed growth and yellows quickly in dry weather.
Mowing should be done with the engine operating at
the RPM recommended for the PTO powering the
deck. Do not mow at high ground speed.
During certain times of the year and under some
conditions, the mower may leave streaks of uncut
grass.
Streaking may occur when attempting to mow heavy
weeds and tall grass. Under these conditions it may
be necessary to go back over the cut area a second
time to get a clean cut.
Figure 72
SECTION 7: SPECIFICATIONS
Engine
Manufacturer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kohler
Horsepower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 OHV
Cooling System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.27 in. (83 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.64 in. (67 mm)
Displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.0 cu. in. (725 ml)
Compression Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0:1
Low Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500 75 rpm
High Idle Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3600 rpm
Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydraulic Lifters
Spark Plug Gap. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .030 in. (0.76 mm)
Crank Case Capacity (With Filter) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 qts. (2.0 L)
Electrical System
Charging System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flywheel-Coil
Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Amp Regulated
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Volt / 500 cca
Starter Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Solenoid Shift
Fuel System
Fuel Tank Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6 gal. (21.1 L)
Fuel Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unleaded Gasoline
Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . In-line
Fuel Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electrical
52
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Transmission
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic
Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2WD
Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cub Cadet Drive System Plus Fluid
Capacity (Includes Hydraulics) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0 gal. (18.9 L)
Shift Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hi/Lo
Forward Travel Speed
Hi Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Forward — 0 to 8.0 mph
Reverse — 0 to 4.0 mph
Lo Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Forward — 0 to 4.0 mph
Reverse — 0 to 2.0 mph
Differential Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Foot Pedal Control
Hydraulic Lift System
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Auxiliary Pump
Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fender Mounted Lever
Pump Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5 gal./min.
Maximum Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1500 psi
Brakes
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External Dual Disc
Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hand Operated Lever
Steering
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hydrostatic Power
Turning Radius . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 in.
Power Take-Off
Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Electric Clutch
Speed
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 540 rpm
Mid/Front (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000 rpm
Shaft Size
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.375 in. (35 mm)
Mid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0 in (25.4 mm)
Horse Power at PTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Tires
Turf-Front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 x 8.5-8
Turf-Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 x 12-12
General Dimensions
Overall Length (w/o Hitch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 in.
Overall Length (w/Hitch) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .103 in.
Overall Width (w/o Deck) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 in.
Overall Width (w/Deck) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72in.
Overall Height (w/o ROPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51 in.
Overall Height (w/ROPS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79 in.
Wheelbase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 in.
Minimum Ground Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 in.
Weight (w/o Deck) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1200 lbs.
Weight (w/Deck) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1350 lbs.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8: OPTIONAL EQUIPMENT AND ACCESSORIES
When purchasing your tractor, you likely had it equipped for your particular needs at the time. You may
wish to obtain additional equipment or accessories to perform other tasks. Refer to the table below for
a list of optional equipment and accessories currently available through your Cub Cadet dealer.
DESCRIPTION
MODEL NUMBER
590-817-100
(1)
Front Hitch Kit
590-810-100
54" Mower Deck
Tractor Cab
590-824-100
590-818-100
(2)
48" Snow Thrower
(3)
590-816-100
PTO Kit - Front
Hydraulic Valve Kit
590-841-100
590-669-100
(4)
42" Rotary Tiller
(4)
590-819-100
60" Finish Mower
Front Weight Bracket/Bumper
590-821-100
590-615-100
(3)
60" Dozer Blade
(4)
590-626-100
590-627-100
590-628-100
590-632-100
60" Rear Blade
(4)
48" Box Blade
(4)
Post Hole Digger
(4)
60" Rake
Angle Kit
590-623-100
590-836-100
590-835-100
190-217B100
590-858-100
590-859-100
590-860-100
759-04077
Rear Weight Box
Canopy
Vacuum Assisted Collection System
PTO Powered Rear Triple Bagger
54" Deck Discharge Chute for 590-858 Bagger
60" Deck Discharge Chute for 590-858 Bagger
Cruise Control Kit
Transmission Oil Heater Kit
759-04039
(1) Requires hydraulic valve kit 590-841-100
(2) Requires front hitch kit 590-817-100 and front PTO kit 590-816-100.
(3) Requires front hitch kit 590-817-100
(4) See TRACTOR WEIGHTING in SECTION 2: OPERATION
54
Download from Www.Somanuals.com. All Manuals Search And Download.
CALIFORNIA EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The California Air Resources Board and MTD Consumer Group Inc are pleased to explain the evaporative emission control system warranty on your 2006 lawn
mower. In California, new lawn mower must be designed, built and equipped to meet the State’s stringent anti-smog standards. MTD Consumer Group Inc must
warrant the EECS on your lawn mower for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your lawn mower.
Your EECS may include parts such as the carburetor, fuel-injection system, the ignition system, catalytic converter, fuel tanks, fuel lines, fuel caps, valves,
canisters, filters, vapor hoses, clamps, connectors, and other associated emission-related components.
Where a warrantable condition exists, MTD Consumer Group Inc will repair your lawn mower at no cost toyou including diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COVERAGE:
This evaporative emission control system is warranted for two years. If any evaporative emission-related part on your equipment is defective, the part will be
repaired or replaced by MTD Consumer Group Inc.
OWNER’S WARRANTY RESPONSIBILITIES:
As the lawn mower owner, you are responsible for performance of the required maintenance listed in your owner’s manual. MTD Consumer Group Inc recom-
mends that you retain all receipts covering maintenance on your lawn mower, but MTD Consumer Group Inc cannot deny warranty solely for the lack of receipts.
As the lawn mower owner, you should however be aware that MTD Consumer Group Inc may deny you warranty coverage if your lawn mower or a part has failed
due to abuse, neglect, or improper maintenance or unapproved modifications.
You are responsible for presenting your lawn mower to MTD Consumer Group Inc’s distribution center or service center as soon as the problem exists. The
warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have a question regarding your warranty coverage, you should
contact the MTD Consumer Group Inc Service Department at 1-800-800-7310.
GENERAL EMISSIONS WARRANTY COVERAGE:
MTD Consumer Group Inc warrants to the ultimate purchaser and each subsequent purchaser that the lawn mower is: Designed, built and equipped so as to
conform with all applicable regulations; and free from defects in materials and workmanship that cause the failure of a warranted part to be identical in all material
respects to that part as described in MTD Consumer Group Inc’s application for certification.
The warranty period begins on the date the lawn mower is delivered to an ultimate purchaser or first placed into service. The warranty period is two years.
Subject to certain conditions and exclusions as stated below, the warranty on emission-related parts is as follows:
1. Any warranted part that is not scheduled for replacement as required maintenance in the written instructions supplied, is warranted for the warranty period
stated above. If the part fails during the period of warranty coverage, the part will be repaired or replaced by MTD Consumer Group Inc according to subsection
(4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period.
2. Any warranted part that is scheduled only for regular inspection in the written instructions supplied is warranted for the warranty period stated above. Any such
part repaired or replaced under warranty will be warranted for the remaining warranty period.
3. Any warranted part that is scheduled for replacement as required maintenance in the written instructions supplied is warranted for the period of time before the
first scheduled replacement date for that part. If the part fails before the first scheduled replacement, the part will be repaired or replaced by MTD Consumer
Group Inc according to subsection (4) below. Any such part repaired or replaced under warranty will be warranted for the remainder of the period prior to the
first scheduled replacement point for the part.
4. Repair or replacement of any warranted part under the warranty provisions herein must be performed at a warranty station at no charge to the owner.
5. Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our distribution centers that are franchised to service the subject
engines or equipment.
6. The lawn mower owner will not be charged for diagnostic labor that is directly associated with diagnosis of a defective, emission-related warranted part,
provided that such diagnostic work is performed at a warranty station.
7. MTD Consumer Group Inc is liable for damages to other engine or equipment components proximately caused by a failure under warranty of any warranted
part.
8. Throughout the lawn mower warranty period stated above, MTD Consumer Group Inc will maintain a supply of warranted parts sufficient to meet the expected
demand for such parts.
9. Any replacement part may be used in the performance of any warranty maintenance or repairs and must be provided without charge to the owner. Such use will
not reduce the warranty obligations of MTD Consumer Group Inc.
10. Add-on or modified parts that are not exempted by the Air Resources Board may not be used. The use of any non-exempted add-on or modified parts by the
ultimate purchaser will be grounds for disallowing a warranty claims. MTD Consumer Group Inc will not be liable to warrant failures of warranted parts caused
by the use of a non-exempted add-on or modified part.
WARRANTED PARTS:
The repair or replacement of any warranted part otherwise eligible for warranty coverage may be excluded from such warranty coverage if MTD Consumer Group
Inc demonstrates that the lawn mower has been abused, neglected, or improperly maintained, and that such abuse, neglect, or improper maintenance was the
direct cause of the need for repair or replacement of the part. That notwithstanding, any adjustment of a component that has a factory installed, and properly
operating, adjustment limiting device is still eligible for warranty coverage. The following emission warranty parts list are covered: Fuel Line, Fuel Line Clamps
Download from Www.Somanuals.com. All Manuals Search And Download.
CUB CADET LLC
MANUFACTURER’S LIMITED WARRANTY FOR
5000, 6000, & 7500 SERIES COMPACT TRACTORS
AND CUB CADET ATTACHMENTS
Without limiting the foregoing, this limited warranty does not provide
coverage in the following cases:
IMPORTANT: To obtain warranty coverage owner must present an
original proof of purchase and applicable maintenance records to the
servicing dealer. Please see the operator’s manual for information on
required maintenance and service intervals.
a. Routine maintenance and related items such as lubricants, filters (oil,
fuel, air and hydraulic), cleaning, tune-ups, brake and/or clutch
inspection, adjustments made as part of normal maintenance, blade
sharpening, set-up, abuse, accident and/or normal wear. It does not
cover incidental costs such as transporting your equipment to and
from the dealer, telephone charges or renting a product temporarily to
replace a warranted product. Specific items not covered are: lamp
bulbs, injection nozzles, fuel injection pumps, glow plugs, strainers,
fuses, brake linings, clutch facings, clutch discs, coolant, rubber
products, glass products, plastic products, packings, belts.
The limited warranty set forth below is given by Cub Cadet LLC with
respect to new merchandise purchased or leased and used in the United
States and/or its territories and possessions, and by MTD Products
Limited with respect to new merchandise purchased or leased and used
in Canada and/or its territories and possessions (either entity
respectively, “Cub Cadet”).
For non-commercial use: Cub Cadet warrants this product (excluding
Batteries as described below) against defects in material and
b. Service completed by someone other than an authorized service
dealer.
workmanship for a period of two (2) years or fifteen-hundred (1500)
operation hours, from the date of original retail purchase or lease
(whichever comes first) for non-commercial use. For commercial uses
and applications: Cub Cadet warrants this product (excluding Batteries
as described below) against defects in material and workmanship for a
period of one (1) year or fifteen-hundred (1500) operation hours, from the
date of original retail purchase or lease (whichever comes first).
c. Cub Cadet does not extend any warranty for products sold or
exported outside of the United States and/or Canada, and their
respective possessions and territories, except those sold through
Cub Cadet’s authorized channels of export distribution.
d. Replacement parts and\or accessories that are not genuine Cub
Cadet parts.
Cub Cadet attachment warranty — ONE YEAR.
e. Transportation charges and dealer off-site service calls.
Cub Cadet Cub Cadet will, at its option, repair or replace, free of charge,
any part found to be defective in materials or workmanship.
There are no implied warranties including without limitation
any implied warranty of merchantability or fitness for a
particular purpose. No warranties shall apply after the
applicable period of express written warranty above. No
other express warranties beyond those mentioned above,
given by any person or entity, including a dealer or retailer,
with respect to any product, shall bind Cub Cadet. The
exclusive remedy is repair or replacement of the product as
set forth above. The terms of this warranty provide the sole
and exclusive remedy arising from the sale and/or lease of
the products covered hereby. Cub Cadet shall not be liable
for any incidental or consequential loss or damage including,
without limitation, expenses incurred for substitute or
replacement lawn care services or for rental expenses to
temporarily replace a warranted product.
Batteries have a one-year prorated limited warranty against defects in
material and workmanship, with 100% replacement during the first three
months. After three months, the battery replacement credit is based on
the months remaining in the twelve (12) month period dating back to the
original date of original sale or lease. Any replacement battery will be
warranted only for the remainder of the original warranty period.
The remedies described in this limited warranty shall only be available if
the product has been operated and maintained in accordance with the
Operator’s Manual furnished with the product, and the product has not
been subject to misuse, abuse, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of other peril
or natural disaster. Damage resulting from the installation or use of any
part, accessory or attachment not approved by Cub Cadet for use with
the product(s) will void your warranty as to any resulting damage. In
addition, Cub Cadet may deny warranty coverage if the hour meter, or
any part thereof, is altered, modified, disconnected or otherwise
tampered with.
Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of the
product shall void this warranty. You assume the risk and liability for
loss, damage, or injury to you and your property and/or to others and their
property arising out of the misuse or inability to use the product.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF
OF PURCHASE AND APPLICABLE MAINTAINCE RECORDS, through
your local authorized service dealer. To locate the dealer in your area;
In the U.S.A.:
Check your Yellow Pages, or contact Cub Cadet LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-877-282- 8684, or log on to our
This limited warranty shall not extend to anyone other than the original
lessee, purchaser or to the person for whom it was purchased as a gift.
In Canada:
Contact MTD Products Limited, Kitchener, ON N2G 4J1,
HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other rights
that vary in different jurisdictions.
Cub Cadet LLC at P.O. Box 361131, Cleveland, Ohio 44136-0019, or call 1-877-282- 8684, or
MTD Canada Ltd. KITCHENER, ON N2G 4J1; Phone 1-800-668-1238
Download from Www.Somanuals.com. All Manuals Search And Download.
|