®
THE PROFESSIONAL AUDIO DIVISION OF CROWN INTERNATIONAL, INC.
®
®
Exported to select countries as Amcron.
™
Studio Reference
PROFESSIONAL STUDIO AMPLIFIERS
OWNER’S MANUAL
©1995 by CROWN INTERNATIONAL, INC.
P.O. Box 1000, Elkhart, Indiana 46515-1000
Telephone: 219-294-8000
Printed on
recycled paper.
™
™
™
™
™
Trademark Notice: Studio Reference, Smart Amp, MPX-6, SMX-6, AMB-5, and grounded bridge™
K80604-0
8/95
are trademarks and Crown, IOC®, ODEP,® IQ System® and P.I.P.® are registered trademarks of
®
Crown International, Inc. Other trademarks are the property of their respective owners.
Download from Www.Somanuals.com. All Manuals Search And Download.
The information furnished in this manual does not include all of the details of design, production, or variations of the
equipment. Nor does it cover every possible situation which may arise during installation, operation or
maintenance. If your unit bears the name “Amcron,” please substitute it for the name “Crown” in this manual. If you
need special assistance beyond the scope of this manual, please contact our Technical Support Group.
Crown Audio Division Technical Support Group
57620 C.R. 105, Elkhart, Indiana 46517 U.S.A.
Phone: 800-342-6939 (U.S.A.) or 219-294-8200 Fax: 219-294-8301
IMPORTANT
STUDIO REFERENCE AMPLIFIERS
REQUIRE CLASS 1 OUTPUT WIRING.
A V I S
C A U T I O N
RISQUE DE CHOC ÉLECTRIQUE
N’OUVREZ PAS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO PREVENT ELECTRIC SHOCK DO
NOT REMOVE TOP OR BOTTOM
COVERS. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSON-
NEL. DISCONNECT POWER CORD
BEFORE REMOVING REAR INPUT
MODULE TO ACCESS GAIN SWITCH.
À PRÉVENIR LE CHOC
ÉLECTRIQUE N’ENLEVEZ
PAS LES COUVERTURES.
RIEN DES PARTIES
UTILES À L’INTÉRIEUR.
DÉBRANCHER LA BORNE
AVANT D’OUVRIR LA
MODULE EN ARRIÈRE.
Magnetic Field
CAUTION! Donotlocatesensitivehigh-gainequip-
ment such as preamplifiers or tape decks directly
above or below the unit. Because this amplifier has
a high power density, it has a strong magnetic field
which can induce hum into unshielded devices that
are located nearby. The field is strongest just above
and below the unit.
WARNING
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT EXPOSE THIS
If an equipment rack is used, we recommend locating
the amplifier(s) in the bottom of the rack and the
preamplifier or other sensitive equipment at the top.
EQUIPMENT TO RAIN OR MOISTURE!
WATCH FOR THESE SYMBOLS:
The lightning bolt
triangle is used to
alert the user to the
risk of electric shock.
The exclamation point
triangle is used to alert the
user to important operating or
maintenance instructions.
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
CONTENTS
1 Welcome.......................................................................... 7
1.1 Features ................................................................... 7
2 Facilities .......................................................................... 8
3 Installation ..................................................................... 10
3.1 Mounting ................................................................ 10
3.2 Cooling ................................................................... 10
3.3 Wiring ..................................................................... 11
3.3.1 Stereo (Two-Channel) Operation................... 12
3.3.2 Bridge-Mono Operation ................................ 12
3.3.3 Parallel-Mono Operation ............................... 13
3.3.4 Input Connection .......................................... 14
3.3.5 Output Connection ....................................... 16
3.3.6 Additional Load Protection............................ 18
3.4 AC Mains Power ..................................................... 18
4 Operation....................................................................... 19
4.1 Precautions............................................................. 19
4.2 Indicators................................................................ 19
4.3 Protection Systems ................................................. 20
4.3.1 ODEP ........................................................... 21
4.3.2 Standby Mode .............................................. 21
4.3.3 Transformer Thermal Protection .................... 21
4.3.4 Circuit Breaker ............................................. 22
4.4 Controls .................................................................. 22
4.5 Filter Cleaning......................................................... 23
5 Technical Information ................................................... 24
5.1 Overview ................................................................ 24
5.2 Circuit Theory ......................................................... 24
5.2.1 Stereo Operation .......................................... 24
5.2.2 Bridge-Mono Operation ................................ 26
5.2.3 Parallel-Mono Operation ............................... 26
6 Specifications................................................................ 27
7 AC Power Draw & Thermal Dissipation ........................ 36
8 Accessories................................................................... 38
8.1 P.I.P. Modules......................................................... 38
9 Service........................................................................... 40
9.1 Worldwide Service .................................................. 40
9.2 North American Service .......................................... 40
9.2.1 Service at a North American Service Center .. 40
9.2.2 Factory Service ............................................ 40
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
ILLUSTRATIONS
1.1 Studio Reference I Amplifier ........................................... 6
2.1 Front Facilities ................................................................. 8
2.2 Rear Facilities ................................................................. 9
3.1 Mounting Dimensions.................................................... 10
3.2 Removing an End Cap .................................................. 10
3.3 Top View of a Rack-Mounted Unit.................................. 10
3.4 Proper Air Flow with a Rack-Mounted Blower ................ 11
3.5 Stereo Wiring ................................................................ 11
3.6 Bridge-Mono Wiring ...................................................... 12
3.7 Parallel-Mono Wiring ..................................................... 13
3.8 Unbalanced Input Wiring............................................... 14
3.9 Balanced Input Wiring ................................................... 14
3.10 Balanced and Unbalanced Phone Plugs ....................... 14
3.11 Subsonic Filter Capacitors ............................................ 15
3.12 Unbalanced RF Filters ................................................... 15
3.13 Balanced RF Filters ....................................................... 15
3.14 Wire Size Nomograph ................................................... 16
3.15 Inductive Load (Transformer) Network ........................... 17
3.16 Loudspeaker Fuse Nomograph ..................................... 18
4.1 Indicators ...................................................................... 19
4.2 Studio Reference Indicator States.................................. 20
4.3 Removing a Handle ...................................................... 22
4.4 Meter Switches ............................................................. 23
4.5 Input Sensitivity and Ground Lift Switches ..................... 23
5.1 Circuit Block Diagram ................................................... 25
6.1 Studio Reference I Minimum Power Matrix .................... 29
6.2 Studio Reference II Minimum Power Matrix .................. 30
6.3 Studio Reference I Maximum Power Matrix ................... 31
6.4 Studio Reference II Maximum Power Matrix ................. 32
6.5 Typical Frequency Response ........................................ 33
6.6 Typical Damping Factor ................................................ 33
6.7 Typical Output Impedance ............................................ 33
6.8 Typical Phase Response ............................................... 34
6.9 Typical Common Mode Rejection .................................. 34
6.10 Typical Crosstalk........................................................... 35
7.1 Studio Reference I Power Draw, Current Draw and
Thermal Dissipation at Various Duty Cycles ................... 36
7.2 Studio Reference II Power Draw, Current Draw and
Thermal Dissipation at Various Duty Cycles ................... 37
8.1 Installing a P.I.P. Module ............................................... 38
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
®
Fig. 1.1 Studio Reference I Amplifier
Unpacking Instructions
Please unpack and inspect your new amplifier for
any damage that may have occurred during transit.
If damage is found, notify the transportation com-
pany immediately. Only you, the consignee, may ini-
tiate a claim for shipping damage. Crown will be
happy to cooperate fully as needed. Save the ship-
ping carton as evidence of damage for the shipper’s
inspection.
Even if the unit arrived in perfect condition, as most
do, save all packing materials so you will have them
if you ever need to transport the unit. NEVER SHIP
THE UNIT WITHOUT THE FACTORY PACK.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
1 Welcome
traditional amplifiers. This results in significantly lower
distortion and superior reliability.
❏ Patented ODEP® (Output Device Emulation Protection)
circuitry detects and compensates for overheating and
overload to keep the amplifier working when others
would fail.
❏ IOC® (Input/Output Comparator) circuitry immediately
alerts you of any distortion that exceeds 0.05% to
provide dynamic proof of distortion-free performance.
The stunning realism you will experience when listen-
ing to a Crown Studio Reference™ amplifier will
redefine your expectations. The evolution of this studio
standard ushers in a new era of powerful, ultraquiet
amplifiers capable of faithfully reproducing the most
demanding signals that state-of-the-art 20-bit digital
recording systems can offer. This kind of sonic integrity
does not happen accidentally. It demands the leader-
ship and technical excellence for which Crown has
long been known.
❏ P.I.P. (Programmable Input Processor) connector
accepts accessories that tailor your amplifier to suit
specific applications.
With the best transfer function in the industry, ultra-high
dynamic range and extraordinary damping factor, your
Studio Reference amplifier comes closer to the ideal
“straight wire with gain” than any other amplifier. As
you listen, it will become apparent—the amplifier’s low-
frequency transient response is the standard by which
all others must be judged.
❏ Extremely wide dynamic range capable of accurately
reproducing 20-bit digital recordings.
❏ Ultra-high damping factor delivers superior loudspeaker
motion control for the cleanest, tightest, chest-thumping
bottom end you’ve ever felt—or heard.
❏ Super-low harmonic and intermodulation distortion give
your amplifier the best transfer function in the business.
We have taken great care at every step in the creation
of your amplifier—from the selection of its components
to the routing of each wire. It is our goal to provide you
with total satisfaction. This is one reason why we have
spent considerable effort in providing you with the
most complete Owner’s Manual in the business.
Please read it carefully—especially the instructions,
warnings and cautions. It will help you successfully
install and use your new amplifier. Be sure to read
Sections 3.3.2 and 3.3.3 if you plan to use one of the
amplifier’s two mono modes.
❏ Two mono modes (Bridge-Mono and Parallel-Mono) for
driving a wide range of load impedances.
❏ Custom-designed, tape-wound, low-noise toroidal
supplies with extremely high power density.
❏ High-voltage headroom and high-current headroom
provide energy reserves that make it easy to drive low-
impedance loads and highly reactive loads to full power.
❏ Full protection against shorted outputs, mismatched
loads, general overheating, DC and high-frequency
overloads. Full overvoltage and internal fault protection.
❏ Indicators include Enable, ODEP, IOC, Signal Presence
Please send in your warranty registration card today
and save your bill of sale because it is your official
proof of purchase. We hope you enjoy your new ampli-
fier, and thank you for choosing Crown.
and the Dynamic Range/Level meter.
❏ Balanced phone jacks and XLR connectors are pro-
vided for input. Two pair of 5-way binding posts per
channel are provided for versatile output connection.
❏ Ground lift switch isolates the AC power and phone jack
1.1 Features
audio grounds.
Studio Reference amplifiers integrate several cutting
edge technologies that make them the most accurate
reference amplifiers available. For example, in Stereo
mode each channel can actually be treated as a sepa-
rate amplifier because of its separate high-voltage
power supplies and ultra-low crosstalk. Here are some
of its many impressive features:
❏ Efficient heat sinks and a self-contained, on-demand,
infinitely variable forced-air cooling system prevents
overheating and prolongs component life.
❏ Internal three-position input sensitivity switch provides
settings of 0.775 volts and 1.4 volts for standard 1 kHz
power, and 26 dB gain.
❏ Mounts in a standard 19 inch (48.3 cm) equipment rack,
or units can be stacked directly on top of each other.
❏ Crown’s unconventional grounded bridge™ circuitry
delivers incredible voltage swings without using
stressful output transistor configurations like other more
❏ Three year “No-Fault” full warranty completely protects
your investment and guarantees its specifications.
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
A
B C D
D C B
A
E
F
®
G
Fig. 2.1 Front Facilities
H
2 Facilities
cators may not flash at very low input signal levels. See
Section 4.2.
A. Level Controls
Each channel’s output level can be adjusted accurately
using the 31-position detented level controls on the front
panel (see Section 4.4).
E. Enable Indicator
This indicator lights when the amplifier has been “en-
abled” or turned on, and AC power is available.
B. ODEP Indicators
During normal operation of the amplifier, the ODEP
(Output Device Emulation Protection) indicators glow
brightly to show the presence of reserve thermody-
namic energy. They dim proportionally as energy
reserves decrease. In the rare event that energy re-
serves are depleted, the indicators turn off and ODEP
proportionally limits the output drive so the amplifier can
safely continue operating even under severe conditions.
These indicators also help to identify more unusual op-
erating conditions (see Figure 4.2).
F. Enable Switch
This push button is used to turn the amplifier on and off.
When turned on, the output is muted for about four sec-
onds to protect your system from start-up transients.
This is why a power sequencer is rarely needed for mul-
tiple units. (The turn-on delay can be changed. Contact
Crown’s Technical Support Group for details.)
G. Dust Filter
The dust filter removes large particles from the air drawn
in by the cooling fan. In most cases, the fan will not run
so the filter will remain clean. If the filter becomes dirty, it
can be removed for easy cleaning (see Section 4.5).
C. IOC Indicators
The IOC (Input Output Comparator) indicators serve as
sensitive distortion indicators to provide proof of
distortion-free performance. Under normal conditions,
the indicators remain off. They flash if the output
waveform differs from the input by 0.05% or more (see
Section 4.2). If the input signal level is too high, the
indicators will also flash brightly with a half-second hold
delay to show input overload or output clipping. Note:
The channel 2 IOC indicator stays on in Parallel-Mono
mode. See Section 4.2.
H. Dynamic Range / Level Meters
A five-segment output meter is provided for each chan-
nel. The meters are factory-set to show dynamic range
of the signals in dB, which is computed as the ratio of
peak to average output power. Also, the meter can op-
tionally be set to show output levels (see Section 4.4).
❏ Meter Switches
Two switches behind the front panel can be used to
customize the output meters (H). By default, the meters
display dynamic range. To make the meters display sig-
nal levels or to turn them off, see Section 4.4.
D. Signal Presence Indicators
These indicators flash synchronously with the amplifier’s
audio output to show signal presence. Note: These indi-
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Fig. 2.2 Rear Facilities
N. Stereo/ Mono Switch
I. Reset Switch
This switch is used to select one of three operating
modes. Stereo mode is used for normal two-channel
operation, Bridge-Mono mode is used to drive a single
channel with a load impedance of at least 4 ohms, and
Parallel-Mono mode is used to drive a single channel
with a load impedance of less than 4 ohms. WARNING:
Turn off the amplifier before changing this switch
(see Section 3.3).
This back panel switch can be used to trip and reset the
AC mains circuit breaker (see Section 4.3.4).
J. Power Cord
For 120 VAC, 60 Hz North American units, the Studio
Reference I includes a 10 AWG power cord and NEMA
TT30P plug, and the Studio Reference II includes a
12 AWG cord and NEMA 5-15P plug. Other units are
shipped with an appropriate power cord and plug.
O. Balanced Phone Jack Inputs
A balanced 1¦4-inch phone jack is provided for input to
each channel. They may be used with either balanced
(tip, ring and sleeve) or unbalanced (tip and sleeve) in-
put wiring (see Section 3.3). These inputs are in parallel
with the P.I.P. connector, so they should not be used as
inputs if the installed P.I.P. has active circuitry. Caution:
Do not use the channel 2 input in either mono mode.
K. P.I.P. Module
The standard P.I.P.-FX input module is provided with
your amplifier. It provides female XLR input connectors.
Each pair of XLR and phone jack connectors is wired in
parallel so the unused connector can be used as a
“daisy chain” output to connect a source to multiple am-
plifiers. Other P.I.P. modules can be used in place of the
P.I.P.-FX to provide additional features that customize
your amplifier for different applications (see Section 8 for
available P.I.P. modules).
P. Ground Lift Switch
The input signal ground may be isolated from the AC
ground with this switch to help prevent unwanted
ground loops. It affects only the phone jacks (O). It has
no affect on the P.I.P. module’s XLR connectors. Activat-
ing the switch inserts an impedance between the sleeve
of each phone input jack and the circuit ground.
L. Balanced XLR Inputs
A balanced three-pin female XLR connector is provided
on the P.I.P.-FX (K) for input to each channel. Caution:
Do not use the channel 2 input in either mono mode.
M. Output Connectors
❑ Input Sensitivity Switch
Two pairs of versatile 5-way binding posts are provided
for the output of each channel so multiple loudspeakers
can be connected easily. They accept banana plugs,
spade lugs or bare wire.
The three-position input sensitivity switch inside the am-
plifier can be accessed by removing the P.I.P. module.
Settings include 0.775 volts and 1.4 volts for rated out-
put, and 26 dB voltage gain (see Section 4.4).
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
3.2 Cooling
3 Installation
Your amplifier has an internal variable speed fan that is
controlled to match the unit’s real-time cooling needs.
With proper installation and typical studio use, the fan
may never need to run. For best results, you should fa-
miliarize yourself with its cooling requirements.
3.1 Mounting
Studio Reference amplifiers are designed for standard
19 inch (48.3 cm) rack mounting or stacking without a
cabinet. In a rack, it is best to mount units directly on
top of each other. This provides the most efficient air
flow and support. If the rack will be transported, we
recommend that you fasten the amplifier’s back panel
securely to the rack to help support the unit’s weight.
Here are some tips to help keep your amplifier cool.
First, never block the amplifier’s front or side air vents.
If the amplifier is rack-mounted, its sides should be at
least 2 inches (5 cm) away from the cabinet (see Fig-
ure 3.3). Also, open rack spaces should be covered to
prevent heated air from the side vents from being
drawn out the front of the rack into the front air intake.
®
7 in
FRONT VIEW
(17.3 cm)
You will know when your Studio Reference amplifier
has sufficient cooling because its ODEP indicators will
be brightly lit. If the amplifier’s ODEP indicators dim or
turn off, overly demanding conditions are forcing it to
protect itself from overheating. If you experience a
cooling problem, you should consider several factors
that may be contributing to the problem, including load
impedance, air flow and ambient air temperature.
19 in
(48.3 cm)
SIDE VIEW
16 in
Low-impedance loads generate more heat than higher
impedance loads. To avoid impedance-related cooling
problems, connect loads to each channel with a total
impedance of at least 2 ohms in Stereo, 4 ohms in
Bridge-Mono, and 1 ohm in Parallel-Mono mode (see
Section 3.3 for wiring instructions). If your loads are
reasonable and you still have a cooling problem, check
for shorts in the loudspeaker cables, and look for prob-
lems with air flow or ambient air temperature.
1.4 in
(3.6 cm)
(40.6 cm)
Fig. 3.1 Mounting Dimensions
Before proceeding, make sure the meter switches are
set to your liking. The front panel assembly must first
be removed to change these switches, so it is easier to
do before the unit is mounted (see Section 4.4).
Airflowrestrictionsarethemostcommoncauseofinad-
equate cooling. Restrictions may result from improper
By now, you may be looking for rack ears. The rack
ears are covered by two attractive end caps which are
held in place by phillips screws (see Figure 3.2). To
use the rack ears, remove the screws and lift off the
caps. With sufficient side clearance, you can reinstall
the end caps once the amplifier is mounted in the rack.
17 in
IMPORTANT: Be sure the back of
the amplifier is supported.
AIR
FLOW
AIR
FLOW
6 in
AMPLIFIER
(TOP VIEW)
2 in
MIN.
RACK
CABINE
AIR FLOW
Fig. 3.2 Removing an End Cap
Fig. 3.3 Top View of a Rack-Mounted Unit
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
FRONT
you may want to install supplemental cooling like a
rack-mounted blower or an air conditioner.
AIR
FLOW
BLOWER
OF
(OPTION 2)
RACK
DOOR
A “squirrel cage” blower can be installed at the bottom
of the rack so it blows outside air into the space be-
tween the door and the front of the amplifiers. This will
pressurize the “chimney” behind the door (Figure 3.4,
Option 1). The blower should not blow air into or take
air out of the space behind the amplifiers. For racks
without a front door, you can evacuate the rack by
mounting the blower at the top of the rack so air blows
out the back (Figure 3.4, Option 2). You can estimate a
rack’s required air flow by adding each unit’s maxi-
mum air flow rating. The Studio Reference I and II can
each move up to 45 cubic feet (1.3 cubic meters) of air
per minute. So if you put one of each in a rack, you
would need 90 cubic feet (2.5 cubic meters) of air flow
through the rack per minute under worst-case condi-
tions (45 cubic feet + 45 cubic feet = 90 cubic feet).
EQUIPMENT
RACK
(SIDE VIEW)
AIR
FLOW
BLOWER
(OPTION 1)
Fig. 3.4 Proper Air Flow with a Rack-Mounted Blower
mounting, pilesofpowercords, cloggeddustfiltersand
closed rack doors. Mount your amplifier to allow suffi-
cient air flow into the front intake, out the side exhaust
vents, andoutthebackoftherack. Anairflowrestriction
likeapileofpowercordscansimplybemovedoutofthe
way. Airfiltersshouldbecleanedusingtheprocedurein
Section 4.5.Ifrackdoorsaretheproblem,youcanleave
them open, remove them, or install a grille. If you install
a grille, we recommend using a wire grille because per-
forated panels restrict air flow by at least 40%.
Another way to increase cooling is to use air condition-
ing. It is rarely a necessity because internal fans and
rack-mounted blowers almost always provide enough
air flow for the most extreme conditions. Still, air condi-
tioning helps reduce the ambient temperature of the air
flowing through the rack. If you plan to use air condi-
tioning, refer to Section 7 for information on calculating
the hourly thermal dissipation of your system.
If your ODEP indicators still dim under demanding con-
ditions, we recommend that you check the table of
indicator states in Figure 4.2 to eliminate other condi-
tions that could be the source of the problem. If it is
clear that the amplifier does not have sufficient air flow,
3.3 Wiring
Figures 3.5 through 3.7 show common ways to set up a
Studio Reference amplifier. Input and output connec-
tors are located on the back panel. Be careful when
STEREO MODE
CHANNEL 2
LOUDSPEAKER
–
+
CHANNEL 1
CHANNEL 1
LOUDSPEAKER
+
–
CHANNEL 2
MIXER
CH-2
CH-1
FX
P U S H
P U S H
S
T
U
D
I
O
Reference
STUDIO REFERENCE
AMPLIFIER
STEREO
PARALLEL
MONO
BRIDGE
MONO
CAUTION: TURN OFF AMPLIFIER
BEFORE CHANGING THIS SWITCH!
Fig. 3.5 Stereo Wiring
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
making connections, selecting sources and controlling
output levels. The load you save may be your own!
Crown is not responsible for damaged loads that result
from carelessness or deliberate overpowering.
mode, turn it off, slide the stereo/mono switch to the
center position, and properly connect the output wiring
as shown in Figure 3.5. Each output channel has two
sets of binding posts to make it easier for you to con-
nect multiple loudspeaker cables to each channel. Be
sure to observe correct loudspeaker polarity (see Fig-
ure 3.5) and be careful not to short the outputs.
CAUTION: Always disconnect the AC power and
turn the level controls down when making or break-
ing connections. This practice reduces the chance of
loud blasts that can cause loudspeaker damage.
CAUTION: In Stereo mode, never tie an amplifier’s
outputs together directly, and never parallel them
with the output of another amplifier. Such connec-
tions do not result in increased output power, but may
activate the protection circuitry to prevent overheating.
Studio Reference amplifiers provide three operating
modes: Stereo, Bridge-Mono and Parallel-Mono. Ste-
reo mode provides standard two-channel operation;
Bridge-Mono provides a single channel with double
the output voltage of Stereo mode; and Parallel-Mono
mode provides a single channel with double the output
current of Stereo mode. These modes can be selected
using the stereo/mono switch on the back panel. Each
mode is wired differently, so be sure to note any spe-
cial wiring requirements for the mode you will be using.
3.3.2 Bridge-Mono Operation
Bridge-Mono mode is used to drive loads with a total
impedance of at least 4 ohms (see Parallel-Mono if the
load is less than 4 ohms). Wiring for Bridge-Mono
mode is different from the other modes and requires
special attention. First, turn off the amplifier. Then se-
lect Bridge-Mono mode by sliding the stereo/mono
switch to the right (as you face the back panel). Both
outputs receive the channel 1 input signal, but chan-
nel 2 is inverted so it can be bridged with channel 1.
Do not use the channel 2 input or signal quality will be
3.3.1 Stereo (Two-Channel) Operation
Stereo mode installation is very intuitive: input chan-
nel 1 feeds output channel 1, and input channel 2
feeds output channel 2. To put the amplifier into Stereo
BRIDGE-MONO MODE
–
+
CHANNEL 1
LOUDSPEAKER
MIXER
DO NOT USE
THE CHANNEL 2
INPUTS.
CH-2
CH-1
FX
DO NOT USE
THE BLACK
BINDING
P U S H
P U S H
POSTS.
S
T
U
D
I
O
Reference
STUDIO REFERENCE
AMPLIFIER
STEREO
PARALLEL
MONO
BRIDGE
MONO
CAUTION: TURN OFF AMPLIFIER
BEFORE CHANGING THIS SWITCH!
Fig. 3.6 Bridge-Mono Wiring
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
greatly degraded. Also, turn down the channel 2 level
control (fully counterclockwise).
is very different from the other modes and requires
special attention.
Note: The channel 2 input and level control are not de-
feated in Bridge-Mono mode. Any signal feeding chan-
nel 2 will work against the channel 1 signal, and usually
results in distortion and inefficient operation.
To select Parallel-Mono mode, turn off the amplifier and
slide the stereo/mono switch to the left (as you face the
back panel). Connect the input signal to channel 1 only.
The channel 2 input and level control are bypassed in
this mode, so they should not be used.
Connect the load across the two red (+) binding posts
(see Figure 3.6). The positive (+) loudspeaker lead
connects to the red channel 1 binding post, and the
negative (–) or ground lead from the loudspeaker con-
nects to the red channel 2 binding post. Do not con-
nect the black binding posts (–). Also, the load must be
balanced (neither side shorted to ground).
Note: It is normal for the channel 2 IOC indicator to stay
on in Parallel-Mono mode.
Connect the load to the channel 1 output as shown in
Figure 3.7. The positive (+) lead from the loudspeaker
connects to the red channel 1 binding post, and the
negative (–) or ground lead from the loudspeaker con-
nects to the black channel 1 binding post. Finally, in-
stall a jumper wire of at least 14 gauge between the
channel 1 and channel 2 red binding posts.
CAUTION: Only connect balanced equipment
(meters, switches, etc.) to the Bridge-Mono output.
Both sides of the line must be isolated from the in-
put grounds or oscillations may occur.
CAUTION: When Parallel-Mono wiring is installed,
do not attempt to operate in Stereo or Bridge-Mono
mode until the wiring is removed (especially the
jumper wire). Failure to do so will result in high dis-
tortion and excessive heating.
3.3.3 Parallel-Mono Operation
Parallel-Mono mode is used to drive loads with a total
impedance of less than 4 ohms (see Bridge-Mono if the
load is 4 ohms or more). Wiring for Parallel-Mono mode
PARALLEL-MONO MODE
–
+
CHANNEL 1
ADD A 14 GAUGE
OR LARGER
JUMPER BETWEEN
THE CHANNEL 1
AND 2 RED (+)
LOUDSPEAKER
MIXER
THE CHANNEL 2
INPUTS ARE
NOT USED
BINDING POSTS
CH-2
CH-1
FX
P U S H
P U S H
S
T
U
D
I
O
Reference
STUDIO REFERENCE
AMPLIFIER
STEREO
PARALLEL
MONO
BRIDGE
MONO
CAUTION: TURN OFF AMPLIFIER
BEFORE CHANGING THIS SWITCH!
Fig. 3.7 Parallel-Mono Wiring
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
3.3.4 Input Connection
+
–
The balanced inputs have a nominal impedance of
10 K ohms (5 K ohms unbalanced) and will accept the
line-level output of most devices. Phone jacks are pro-
vided on the back panel, while the factory-installed
P.I.P.-FX provides female XLR input connectors (see
Figure 2.2). Optional P.I.P. modules like the P.I.P.-BB
and the P.I.P.-FPX can provide barrier block and
phono (RCA) connectors. Various P.I.P.s are also avail-
able which provide a wide range of input signal pro-
cessing features (see Section 8).
Note: If two or more channels with
the same input ground reference
are driven from the same
3
1
2
INPUT
floating source, connect
Floating
source
only one shield to the
source chassis.
Output
–
+
2-wire line cord
(or battery power)
+
–
3
Correct input wiring depends on two factors:
(1) whether the input signal is balanced or unbal-
anced, and (2) whether the signal floats or has a
ground reference. Figures 3.8 and 3.9 show the recom-
mended connection techniques for each combination
of source signal characteristics.
1
2
INPUT
Grounded
source
Shield not connected
at this end
Output
–
+
3-wire grounded line cord
(or other ground connection)
+
–
3
Fig. 3.9 Balanced Input Wiring
1
2
INPUT
Shield connected
to ground terminal
Floating
source
1
The amplifier’s built-in ¦4-inch input phone jacks can
be wired similarly for balanced or unbalanced, floating
or ground-referenced sources. They have a standard
tip-ring-sleeve (TRS) configuration: the tip is positive
(+), the ring is negative (–) and the sleeve is ground
(see Figure 3.10). Wiring for various sources follows
the XLR wiring examples in Figures 3.8 and 3.9.
Output
+
2-wire line cord
(or battery power)
+
–
3
1
2
INPUT
Shield is not
connected
at this end
Grounded
source
If you install a P.I.P. module other than the P.I.P.-FX,
P.I.P.-BB, P.I.P.-FMX or P.I.P.-FPX, do not connect in-
put signals to the phone jacks. The phone jacks are in
parallel with the output of the P.I.P. module, so the
source connected to the phone jacks can feed into the
P.I.P. and generate a distortion in the output. The
phone jacks can still be used as “daisy chain” outputs
to feed the post-processed signal from the P.I.P. to the
input of other amplifiers.
Output
+
3-wire grounded line cord
(or other ground connection)
+
–
3
1
2
INPUT
Floating
source
Shield connected to both
negative (–) and ground
input terminals
If the amplifier will be used in Bridge-Mono or Parallel-
Mono mode, be sure to follow the instructions provided
in Sections 3.3.2 and 3.3.3. Do not use the channel 2
input in either mono mode.
Output
+
2-wire line cord
(or battery power)
+
–
3
+
1
2
INPUT
Input ground
terminal not used
BALANCED
–
Grounded
source
SHIELD
Output
+
+
UNBALANCED
3-wire grounded line cord
(or other ground connection)
SHIELD
Fig. 3.8 Unbalanced Input Wiring
Fig. 3.10 Balanced and Unbalanced Phone Plugs
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
470 ohms
SOLVING INPUT PROBLEMS
+
+
.0056
µf
Sometimes large subsonic (subaudible) frequencies
are present in the input signal. These can damage
loudspeakers by overloading or overheating them. To
attenuate such frequencies, place a capacitor in series
with the input signal line. The graph in Figure 3.11
shows some capacitor values and how they affect the
frequency response of a Studio Reference amplifier.
Use only low-leakage capacitors.
Balanced In
A
B
C
D
Balanced Out
–
–
470 ohms
1.8 mH
+
+
.015
µf
Balanced In
Balanced Out
–
–
1.8 mH
2.5 mH
+
+
.018
dB
Balanced In
Balanced Out
µf
–
–
0
2.5 mH
0.47 Film 1.8 mH
–5
+
+
–10
–15
.015
Balanced In
Balanced Out
µf
–
–
0.47 Film 1.8 mH
1 Hz
10 Hz
100 Hz
1 kHz
10 kHz
Fig. 3.13 Balanced RF Filters
Frequency
Fig. 3.11 Subsonic Filter Capacitors
Tip: The P.I.P.-FX has plenty of space on its circuit
board for the addition of input filter circuitry.
Another problem to avoid is large levels of radio fre-
quencies or RF in the input signal. Although high RF
levels may not pose a threat to the amplifier, they can
burn out tweeters or other loads that are sensitive to
high frequencies. Extremely high RF levels can also
cause your amplifier to prematurely activate its protec-
tion circuitry, resulting in inefficient operation. RF can
be introduced into a signal by local radio stations and
from the bias signal of many tape recorders. To pre-
vent high levels of input RF, install an appropriate
low-pass filter in series with the input signal. Some ex-
amples of unbalanced wiring for low-pass filters are
shown in Figure 3.12.
Another problem to avoid is ground loops. These are
undesired currents that flow in a grounded system and
usually cause hum in the output. A common source of
ground loop problems is the placement of input cables
parallel to power cables or near power transformers.
The magnetic field that surrounds these conductors
can induce the 50 or 60 Hz alternating current into your
input cables. To prevent this type of ground loop, it is
always a good idea to locate input cables away from
Input Wiring Tips
1. Use only shielded cable. Cables with
higher density shields are better. Spiral
wrapped shield is not recommended.
910 ohms
dB
To
Amp
.0056
µf
Source
0
GND
6 dB/octave
A
3.9 mH
2. When using unbalanced lines, keep the
cables as short as possible. Avoid cable
lengths greater than 10 feet (3 meters).
A
To
12 dB/octave
Amp
–10
–20
.015
600 ohm
Source
B
R
R
µf
GND
C
B
5 mH
3. Do not run signal cables together with
high-level wiring such as loudspeaker wires
or AC cords. This reduces the chance of
hum or noise being induced into the input
cables.
To
Amp
.018
600 ohm
Source
µf
GND
C
4 kHz
10 kHz
40 kHz
100 kHz
Note: A low source impedance (R) can be
increased to 600 ohms with an appropriate resistor.
Frequency
4. Turn the entire system off before chang-
ing connections. Turn level controls down
before powering the system back up. Crown
is not liable for damage incurred when any
transducer or component is overdriven.
Fig. 3.12 Unbalanced RF Filters
For balanced input wiring, use an example from Fig-
ure 3.13. Filters A, B and C correspond to the
unbalanced filters shown in Figure 3.12. Filter D also
incorporates the subsonic filter in Figure 3.11.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
power cables and power transformers. We also recom-
mend using shielded or twisted pair wire. With loose
wires, use tie-wraps to bundle together each pair of in-
put wires. This helps reduce magnetically-induced
current by minimizing the cross-sectional area be-
tween conductors that could bisect the magnetic field.
the damping factor decreases as the cable resistance
increases. This is very important because the ampli-
fier’s excellent damping factor can be easily negated
by using insufficient cable.
Use the nomograph in Figure 3.14 and the procedure
that follows to find the recommended wire gauge
(AWG or American Wire Gauge) for your system.
Ground loops often occur when the input and output
grounds are tied together. DO NOT CONNECT THE
INPUT AND OUTPUT GROUNDS TOGETHER. Tying
the grounds together can also cause feedback oscil-
lation from the load current flowing in the loop. To
avoid this problem, use proper grounding, isolate the
inputs, and isolate other common AC devices. When
using the input phone jacks, the signal grounds can be
isolated from the AC mains ground with the ground lift
switch located on the amplifier’s back panel (see Fig-
ure 2.2 and Section 4.4).
.0002
R
S
SOURCE
RESISTANCE
(ohms)
.0004
.0006
.001
.002
R
R
L
S
DAMPING
FACTOR
20,000
.004
.006
10,000
.01
.02
5,000
3.3.5 Output Connection
Consider the rated power-handling capacity of your
load before connecting it to the amplifier. Crown is not
liable for damage incurred at any time due to overpow-
ering. Fusing loudspeaker lines is highly recom-
mended (see Section 3.3.6). Also, please pay close
attention to Section 4.1, Precautions.
2,000
1,000
R
COPPER
WIRE
8000
5000
L
40
30
.04
.06
LOAD
RESISTANCE
(ohms)
(AWG)
(ohms/1000 ft.)
500
.1
.2
1000
2-COND.
200
100
CABLE
(feet)
500
1
20
15
2
5
#28
#26
#24
#22
100
50
50
You should always install loudspeaker cables of suffi-
cient gauge (wire thickness) for the length used. The
resistance introduced by inadequate output wiring will
reduce the amplifier’s power to and motion control of
the loudspeakers. The latter problem occurs because
.4
.6
10
20
50
20
10
#20
#18
#16
#14
#12
#10
#8
1
2
100
10
5
200
500
5
1000
10
9
2000
5000
1
#6
4
6
2
1
#4
.5
8
#2
7
6
#0
#00
10
20
40
.1
#0000
.05
Use Good Connectors
5
4
1. Male connectors on loudspeaker cables
should not be exposed to prevent possible
short circuits.
.01
3
2. Connectors which might accidentally
cause the two channels to be tied together
when making and breaking connections
should not be used. (A common example is
the standard three-wire stereo phone plug.)
Example Shown:
R
= 8 ohms; R = 0.016 ohms or D.F. = 500;
L
S
Cable Length = 10 ft.; answer: #8 wire
2
1.5
3. Connectors which can be plugged into
AC power receptacles should never be used.
1
0.9
0.8
4. Connectors having low current-carrying
capacity should not be used.
0.7
0.6
5. Connectors having any tendency to short
should never be used.
0.5
Fig. 3.14 Wire Size Nomograph
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
1. For loads connected in parallel, use the equation that
follows to calculate each channel’s total load resistance.
Substitute the rated impedance of the connected loud-
speakers for the Zs in the equation. When finished, mark
your answer on the nomograph’s “Load Resistance” line.
amplifiers share a common cable tray or jacket,
use tie-wraps to bundle individual conductors so
the wires for each loudspeaker are kept close
together. (Do not bundle wires from different
amplifiers.) This reduces the chance of conduc-
tors acting like antennas to transmit or receive the
high frequencies that can cause oscillation.
Total Load Resistance in Ohms = (1¦Z + 1¦Z + 1¦Z3…)–1
1
2
2. Select an acceptable damping factor and mark it on
the “Damping Factor” line. Your amplifier can provide an
phenomenal damping factor of 20,000 from 10 to 200 Hz
in Stereo mode with an 8 ohm load. In contrast, most
other amplifiers have a damping factor rating of 200 or
less. Higher damping factors yield lower distortion and
greater motion control over the loudspeakers. To give you
a basis for comparison, effective damping factors for
commercial applications typically run between 50 and
100. Higher damping factors may be desirable for live
sound, but long cable lengths often limit the highest
damping factor that can be achieved practically. (Under
these circumstances, Crown’s IQ System is often used so
amplifiers can be easily monitored and controlled when
they are located very near the loudspeakers.) In record-
ing studios and home hi-fi, a damping factor of 500 or
more is very desirable.
2. Avoid using shielded loudspeaker cable.
3. Never tie together input and output grounds.
4. Never tie together the output of different amplifiers.
5. Keep output cables separated from input cables.
6. Install a low-pass filter in series with each input
(see Section 3.3.4).
7. Install the input wiring according to the instruc-
tions in Section 3.3.4.
Another problem to avoid is the presence of large
subsonic currents when primarily inductive loads are
used. Examples of inductive loads are 70-volt step-up
transformers and electrostatic loudspeakers.
Inductive loads can appear as a short circuit at low fre-
quencies. This can cause the amplifier to produce
large low-frequency currents and activate its protec-
tion circuitry. Always take the precaution of installing a
high-pass filter in series with the amplifier’s input when
inductive loads are used. A three-pole, 18 dB per oc-
tave filter with a –3 dB frequency of 50 Hz is recom-
mended (some applications may benefit from an even
higher –3 dB frequency). Such a filter is described with
the subsonic frequency problems in Section 3.3.4.
3. Draw a line through the two points with a pencil, and
continue until it intersects the “Source Resistance” line.
4. On the “2-Cond. Cable” line, mark the length of the
cable run.
5. Draw a pencil line from the mark on the “Source Resis-
tance” line through the mark on the “2-Cond. Cable” line,
and on to intersect the “Annealed Copper Wire” line.
6. The required wire gauge for the selected wire length and
damping factor is the value on the “Annealed Copper Wire”
line. Note: Wire size increases as the AWG gets smaller.
Another way to protect inductive loads from large low-
frequency currents and prevent the amplifier from pre-
maturely activating its protective systems is to parallel
a 590 to 708 mF nonpolarized motor start capacitor and
4-ohm, 20-watt resistor in series with the amplifier out-
put and the positive (+) transformer lead. This circuit is
shown in Figure 3.15. It uses components that are
7. If the size of the cable exceeds what you want to use,
(1) find a way to use shorter cables, like using the IQ Sys-
tem, (2) settle for a lower damping factor, or (3) use more
than one cable for each line. Options 1 and 2 will require the
substitution of new values for cable length or damping factor
in the nomograph. For option 3, estimate the effective wire
gauge by subtracting 3 from the apparent wire gauge every
time the number of conductors of equal gauge is doubled.
So, if #10 wire is too large, two #13 wires can be substituted,
or four #16 wires can be used for the same effect.
4-ohm, 20-watt
Resistor
+
SOLVING OUTPUT PROBLEMS
+
–
590 to 708 µf Capacitor
120 VAC, N.P.
High frequency oscillations can cause your amplifier
to prematurely activate its protection circuitry. The ef-
fects of this problem are similar to the effects of the RF
problem described in Section 3.3.4. To prevent high-
frequency oscillations, follow these guidelines:
From
Amplifier
Output
Inductive
Load
–
1. When using long cable runs, or when different
Fig. 3.15 Inductive Load (Transformer) Network
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
available from most electrical supply stores.
A better approach is to fuse each driver independently.
This allows you to apply the most appropriate protec-
tion for the type of driver being used. In general, low-
frequency drivers (woofers) are most susceptible to
thermal damage and high-frequency drivers (tweeters)
are usually damaged by large transient voltages. This
means that your loudspeakers will tend to have better
protection when the woofers are protected by slow-
blow fuses and high-frequency drivers are protected
by high-speed instrument fuses.
3.3.6 Additional Load Protection
Studio Reference amplifiers can deliver very high
power levels, so it’s a good idea to add protection for
your loudspeakers if it is not built-in. Loudspeakers are
subject to thermal damage from sustained overpower-
ing and mechanical damage from large transient volt-
ages. In both cases, fuses may be used to protect your
loudspeakers, or you may opt for the convenience of a
P.I.P. module that provides similar protection.
Depending on the application, you may want to use a
specialized P.I.P. module to protect your loudspeak-
ers. Again, some modules are more appropriate for
long-term thermal protection, while others are more ap-
propriate for protection against transients. A
Smart Amp™ IQ-P.I.P. module is most commonly used
for long-term loudspeaker thermal protection. Each
Smart Amp channel provides an independent “smooth
output limiter” that controls average output levels over
time while it allows transients to pass.
Thermal protection and voltage protection require dif-
ferent types of fuses. Slow-blow fuses are used to pre-
vent thermal damage because they respond to thermal
conditions like a loudspeaker. High-speed instrument
fuses like the Littlefuse 361000 series are used to pro-
tect loudspeakers from transient voltages. The nomo-
graph in Figure 3.16 can be used to select the correct
fuse for thermal or voltage protection.
There are two common ways to install the fuses. One
approach is to put a single fuse in series with each out-
put. This is easy because there is only one fuse per
channel to install. But if the fuse blows, power is re-
moved to all of the connected loads.
Most of the other P.I.P. modules that provide signal-
driven compression can be used to prevent loud-
speaker damage from transient voltage. These
modules include the P.I.P.-AMCb, P.I.P.-EDCb and
P.I.P.-PA. While the P.I.P.-EDCb is most commonly
used for general loudspeaker protection, the
P.I.P.-AMCb is very popular in systems that require a
high-quality crossover, and the P.I.P.-PA is the proces-
sor of choice for applications that require a microphone
and line level input for each channel. And finally, the
Smart Amp IQ-P.I.P.-DP provides both an input com-
pressor for transient protection and a smooth output
limiter for long-term thermal protection. For more infor-
mation on P.I.P. modules, see Section 8.
1.0
1.2
1.4
1.6
20
2
3000
15
2000
1500
2.5
3
10
8
1000
800
6
5
600
4
5
400
300
4
3
3.4 AC Mains Power
200
150
All Studio Reference amplifiers are shipped with an
appropriate line cord and plug. The 120 VAC, 60 Hz
North American Studio Reference I has a special
TT30P plug and includes a matching receptacle. Al-
ways use an isolated power receptacle whenever pos-
sible with adequate voltage and current. Excessive line
voltages 10% or higher above the rated voltage will
cause the amplifier to activate its standby mode (see
Section 4.3.2). For example, do not exceed a 132 VAC
with models rated for 120 VAC operation.
6
2
Example:
100
80
Impedance = 8 ohms.
Peak Power = 75 W
7
8
1.5
60
Answer: Fuse = 1.5 A
1
9
40
30
.8
10
.6
.5
.4
12
20
15
14
16
10
8
.3
6
20
25
4
3
.2
Unless otherwise noted, all specifications in this
manual were measured using 120 VAC, 60 Hz power
mains with voltage accurate to within 0.5% and THD of
less than 1.0% under all test conditions. Performance
variations can occur at other AC mains voltages and
line frequencies. Line regulation problems will directly
affect the output power available from the amplifier.
.15
2
30
40
1.5
1
.1
.08
Fig. 3.16 Loudspeaker Fuse Nomograph
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
4 Operation
4.1 Precautions
Although your amplifier is protected from internal and
external faults, you should still take the following pre-
cautions for optimum performance and safety:
1. Improper wiring for the Stereo, Bridge-Mono or
Parallel-Mono modes can result in serious operat-
ing difficulties (see Sections 3.3.1 through 3.3.3).
Fig. 4.1 Indicators
2. When driving an inductive load like an electrostatic
loudspeaker, use a high-pass filter or protective
network to prevent premature activation of the
amplifier’s protection circuitry (see Section 3.3.4).
power supply and on-demand forced air cooling sys-
tem are working. It does not indicate the status of the
high-voltage power supplies. For example, the enable
indicator will stay on in the improbable event that one
or both channels overheat causing an internal shut
down of the high voltage supplies.
3. WARNING: Do not change the position of the ste-
reo/mono switch unless the amplifier is first turned
off.
The green ODEP indicators confirm the normal opera-
tion of Crown’s patented Output Device Emulation Pro-
tection circuitry. During normal operation, they glow
brightly to confirm the presence of reserve thermody-
namic energy. They dim proportionally as the energy
reserve decreases. In the rare event that there is no
reserve, the indicators will turn off and ODEP will pro-
portionally limit the drive level of the output stages so
the amplifier can continue safe operation even when
the operating conditions are severe. (For a more de-
tailed description of ODEP, see Section 4.3.1.)
4. CAUTION: In Parallel-Mono mode, a jumper must
be installed between the channel 1 and 2 red (+)
binding post outputs. Be sure to remove this jumper
for Stereo or Bridge-Mono modes, otherwise high
distortion and excessive heating will occur. Check
the stereo/mono switch on the back panel for
proper position.
5. Turn off the amplifier and unplug it from the AC
mains before removing the amplifier’s P.I.P. mod-
ule or dust filter.
6. Use care when making connections, selecting sig-
nal sources and controlling the output level. The
load you save may be your own!
A channel’s ODEP indicator also turns off if its high-
voltage power supply is put in “standby” mode or the
amplifier’s circuit breaker is tripped. The standby
mode is activated if DC or heavy common-mode cur-
rent is detected in the output, if the transformer thermal
protection system is activated, if a P.I.P. like the Smart
Amp IQ-P.I.P. is used to shut down a high-voltage sup-
ply, or if excessive AC mains voltage is detected. For
more information see Section 4.3 and the table in Fig-
ure 4.2.
7. Do not short the ground lead of an output cable to
the input signal ground. This will form a ground
loop and may cause oscillations.
8. Operate the amplifier from AC mains of not more
than 10% above or below the selected line voltage
and only at the rated line frequencies.
9. Never connect the output to a power supply output,
battery or power main. Such connections may re-
sult in electrical shock.
The yellow IOC indicators act as sensitive distortion
meters to provide proof of distortion-free performance.
The IOC (Input/Output Comparator) circuitry compares
the incoming signal’s waveform to that of the output.
Any difference between the two is distortion. The IOC
indicators flash if there is a difference of 0.05% or
more. The IOC indicators also show input overload by
flashing brightly with a half-second hold delay. It is nor-
mal for them to light momentarily when the amplifier is
first turned on. Note: The channel 2 IOC indicator will
stay on in Parallel-Mono mode. Also, an IOC indicator
will stay on in abnormal situations where a high-voltage
power supply is temporarily put in standby mode.
10. Tampering with the circuitry by unqualified person-
nel, or making unauthorized circuit changes may
be hazardous and invalidates all agency listings.
Remember: Crown is not liable for damage that results
from overdriving other system components.
4.2 Indicators
The front panel has several helpful indicators. The en-
able indicator is provided to show the amplifier has
been turned on (or enabled) and that its low-voltage
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
As dynamic range meters they show each channel’s
ratio of peak-to-average power in dB. The dynamic
range may be low for sources like AM/FM radio or low-
quality recordings. Other sources like live music or
high-quality recordings may be much higher. As out-
put level meters they show how high the output levels
are in dB relative to full power. At 0 dB, the unit is deliv-
ering full standard 1 kHz power (see Section 6).
The green signal presence indicators flash synchro-
nously with the amplifier’s output signal. The signal de-
tector is connected to the signal path after the input
gain stages and level controls, so a flashing indicator
tells you that there is audio in and out of the amplifier.
Note: The signal presence indicators may not report
signal presence if the output signal level is too low.
The dynamic range /level meters are five-segment
output meters that can be set to monitor either the dy-
namic range or the level of the output signal. They are
factory-set to show dynamic range. A switch located
behind the front panel is used to select the meter dis-
play mode (see Section 4.4 for complete instructions).
4.3 Protection Systems
Studio Reference amplifiers provide extensive protec-
tion and diagnostics capabilities. Protection systems
include ODEP, standby mode, an AC circuit breaker
Indicator Status
Amplifier Condition
ODEP IOC SIGNAL
There is no power to the amplifier. Possible reasons: (1) The amplifier’s enable switch is off. (2) The
amplifier is not plugged into the power receptacle. (3) The AC mains circuit breaker has been tripped.
(4) The amplifier’s circuit breaker has been tripped.
OFF OFF OFF
ODEP IOC SIGNAL
Normal operation for a channel with NO output. Possible reasons: (1) There is no input signal.
(2) The input signal level is very low. (3) The channel’s level control is turned down.
ON OFF OFF
ODEP IOC SIGNAL
The amplifier is in standby mode. Possible reasons: (1) The amplifier has just been turned on and
is still in the four second turn-on delay. (2) A P.I.P. module such as an IQ-P.I.P. has turned off the
channel’s high-voltage supply. (3) The DC/ low-frequency protection circuitry has been activated.
(4) The fault protection circuitry has been activated. (5) The transformer thermal protection circuitry
has been activated. (6) The overvoltage protection circuitry has been activated.
OFF ON OFF
ODEP IOC SIGNAL
ODEP limiting is about to begin or has just ended. Possible reasons: (1) The amplifier’s air filter is
blocked and needs to be cleaned. (2) There is insufficient cooling because of inadequate air flow or air
that is too hot. (3) The load impedance for the channel is too low because the output is shorted or the
amplifier is driving too many loudspeakers for the selected stereo/mono mode. (4) The amplifier
channel is continuously being driven to very high output levels.
OFF OFF Active
ODEP IOC SIGNAL
Channel 2 only: The amplifier is in Parallel-Mono mode with no output. The channel 2 IOC indi-
cator always turns on when the amplifier’s stereo/mono switch is moved to the Parallel-Mono position.
ON
ON OFF
ODEP IOC SIGNAL
Normal operation for a channel with audio output. The ODEP indicator will remain at full intensity
to show that there is reserve thermal-dynamic energy and the signal presence indicator will flash to
show that there is audio output.
ON OFF Active
ODEP IOC SIGNAL
ODEP limiting has been activated. Possible reasons: (1) The amplifier’s air filter is blocked and needs
to be cleaned. (2) There is insufficient cooling because of inadequate air flow or air that is too hot.
(3) The load impedance for the channel is too low because the output is shorted or the amplifier is
driving too many loudspeakers for the selected stereo/mono mode. (4) The amplifier channel is
continuously being driven to very high output levels.
OFF ON Active
ODEP IOC SIGNAL
The channel’s output is exceeding 0.05% distortion. The input signal level is too high, and IOC is
reporting either an input overload or output clipping.
OR
ON
ON Active
Channel 2 only: The amplifier is in Parallel-Mono mode and has output. The channel 2 IOC indi-
cator always turns on when the amplifier’s stereo/mono switch is moved to the Parallel-Mono position.
Fig. 4.2 Studio Reference Indicator States
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
and transformer thermal protection. These systems will
prevent amplifier damage in virtually any situation.
The amplifier’s overvoltage protection circuitry will
put both channels into standby when excessive AC
mains voltage is detected. Studio Reference amplifiers
should not be operated with an AC mains voltage of
more than 10% over the unit’s rated voltage.
4.3.1 ODEP
Crown invented ODEP to solve two long-standing
problems in amplifier design: to prevent amplifier shut-
down during demanding operation and to increase the
efficiency of output circuitry.
If dangerous subsonic frequencies or direct current
(DC) is detected in the amplifier’s output, the unit will
activate its DC / low-frequency protection circuitry
and put the affected channels in standby. This protects
the loads and prevents oscillations. The amplifier re-
sumes normal operation as soon as it no longer detects
dangerous low-frequency or DC output. Although it is
extremely unlikely that you will ever activate the
amplifier’s DC / low-frequency protection system, im-
proper source materials such as subsonic square
waves or input overloads that result in excessively
clipped signals can activate this system.
To do this, Crown established a rigorous program to
measure the safe operating area (SOA) of each output
transistor before installing it in an amplifier. Next,
Crown designed intelligent circuitry to simulate the in-
stantaneous operating conditions of the output transis-
tors. Its name describes what it does: Output Device
Emulation Protection or ODEP. In addition to simulating
the operating conditions of the output transistors, it also
compares their operation to their known SOA. If ODEP
sees that more power is about to be asked of the output
transistors than they are capable of delivering under
the present conditions, ODEP immediately limits the
drive level until it falls within the SOA. Limiting is pro-
portional and kept to an absolute minimum—only what
is required to prevent output transistor damage.
The amplifier’s fault protection system will put an am-
plifier channel into standby mode in rare situations
where heavy common-mode current is detected in the
channel’s output. The amplifier should never output
heavy common-mode current unless its circuitry is
damaged in some way, and putting the channel into
standby mode helps to prevent further damage.
This level of protection enables Crown to increase out-
put efficiency to never-before-achieved levels while
greatly increasing amplifier reliability.
The amplifier’s transformer thermal protection cir-
cuitry is activated in very unusual circumstances where
the unit’s transformer temperature rises to unsafe lev-
els. Under these abnormal conditions, the amplifier will
put both channels into standby mode. The amplifier will
return to normal operation after the transformer cools to
a safe temperature. (For more information on trans-
former thermal protection, refer to the section that fol-
lows.)
The on-board intelligence is monitored two ways. First,
the amplifier’s ODEP indicators show whether the unit
is functioning correctly or if ODEP is limiting output.
Second, ODEP data is fed to the amplifier’s internal
P.I.P. connector so advanced P.I.P. modules like the
IQ-P.I.P. can use it to monitor and control the amplifier.
This is how ODEP keeps the show going with maxi-
mum power and maximum protection at all times.
4.3.3 Transformer Thermal Protection
All Studio Reference amplifiers have transformer ther-
mal protection which protects the power supplies from
damage under rare conditions where the transformer
temperature rises too high. A thermal switch embed-
ded in the transformer removes power to the high-volt-
age power supplies if it detects excessive heat. The
switch automatically resets itself as soon as the trans-
former cools to a safe temperature.
4.3.2 Standby Mode
An important part of a Studio Reference amplifier’s pro-
tection systems is standby mode. Standby protects the
amplifier during potentially catastrophic conditions. It
temporarily removes power from the high-voltage sup-
plies to protect the amplifier and its loads. Standby
mode can be identified using the table in Figure 4.2.
Standby mode is activated in five situations. First, when
you turn on the enable switch, standby mode is acti-
vated to provide turn-on protection. This power-up de-
lay lets other system components settle before any
signals are amplified and it provides some power-up
“randomness” for multiple units so the system’s start-up
current demands are better distributed over time.
If your amplifier is operated within rated conditions, it is
extremely unlikely that you will ever see it activate
transformer thermal protection. One reason is that
ODEP keeps the amplifier working under very severe
conditions. Even so, higher than rated output levels,
excessively low-impedance loads and unreasonably
high input signals can generate more heat in the trans-
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
former than in the output devices. This can overheat
the transformer and activate its protection system.
Each of the front panel level controls has 31 detents
for accurately repeatable settings. In Bridge-Mono and
Parallel-Mono modes, the channel 2 level control
should be turned down.
Studio Reference amplifiersaredesignedtokeepwork-
ing under conditions where other amplifiers would fail.
But even when the limits of a Studio Reference amplifier
are exceeded, it still protects itself—and your invest-
ment—from damage.
The meter switches are located behind the front
panel. They make it possible to switch between the dy-
namic range and signal level display modes for the
meters, or you can turn the meters off. From the factory,
the meters automatically display dynamic range
(which is computed as the ratio of peak to average out-
put power). To change these switches, you will need to
remove part of the front panel. A phillips screwdriver
will be needed, and it will help to remove the amplifier if
it is mounted in a rack. Follow these steps:
4.3.4 Circuit Breaker
A back panel circuit breaker is provided to prevent ex-
cessive current draw by the high-voltage power sup-
plies. A Studio Reference I configured for 100 to
120 VAC has a 30 amp circuit breaker, while the 220 to
240 VAC version has a 20 amp circuit breaker. A Stu-
dio Reference II configured for 100 to 120 VAC uses a
20 amp circuit breaker, and the 220 to 240 VAC ver-
sion has a 10 amp circuit breaker. With rated loads and
output levels, this breaker should only trip in the incred-
ibly rare instance of a catastrophic amplifier failure. The
ODEP system keeps the amplifier safe and operational
under most other severe conditions. The breaker can
also trip in situations where extremely low-impedance
loads and high output levels result in current draw that
exceeds the breaker’s rating. Again, this should only
be possible when operating outside rated conditions,
like when the amplifier is used to drive a 1 ohm load, or
when an input signal is clipped severely.
1. Make sure the amplifier is turned off and its power
cord is disconnected from the AC mains source.
2. Remove the two screws that hold each end cap in
place and remove both end caps (see Figure 3.2).
3. Remove the six screws that hold each handle in
place and remove each handle (see Figure 4.3).
4. Remove the dust filter by gently pulling it away from
the front panel.
5. Remove the two screws that secure the lower half of
the front panel and remove the lower front panel.
6. Locate the meter switches as shown in Figure 4.4.
Set the switches as desired. The left switch is used
to turn the meters on and off, and the right switch is
used to change display modes.
4.4 Controls
The front panel enable switch is used to turn the ampli-
fier on and off. If you ever need to make any wiring or
installation changes, don’t forget to disconnect the
power cord first. Please follow these steps when first
turning on your amplifier:
7. Reassemble the front panel, handles and end caps
in reverse order of disassembly.
8. Install the amplifier and reconnect power.
1. Turn down the level of your audio source. For
AMPLIFIER TOP VIEW
(FRONT LEFT CORNER—END CAP REMOVED)
example, set your mixer’s volume to –• (off).
2. Turn down the amplifier’s level controls.
3. Turn on the enable switch. The enable indicator be-
side the switch should glow. During the four second
turn-on delay that immediately follows, the indica-
tors will flash as described in Figure 4.2. After the
delay, the ODEP indicators should come on with full
brilliance and the IOC and signal presence indica-
tors should function normally.
4. After the turn-on delay, turn up your source to the
maximum desired level.
5. Turn up the amplifier’s level controls until the maxi-
mum desired sound level is achieved.
To remove the handle,
pull firmly from the side.
6. Turn down the level of your audio source to its
normal range.
Fig. 4.3 Removing a Handle
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
METER ON/OFF SWITCH
OFF
ON
®
OUTPUT LEVEL
DYNAMIC RANGE
METER MODE SWITCH
Fig. 4.4 Meter Switches
The input sensitivity switch is located inside the
amplifier’s P.I.P. compartment. It is factory-set to a
fixed voltage gain of 26 dB. For standard 1 kHz power
into 8 ohms, this is equivalent to an input sensitivity of
4.0 volts for the Studio Reference I and 2.7 volts for the
Studio Reference II. If needed, it can be switched to a
sensitivity of 0.775 or 1.4 volts. Here is the procedure:
switch to the left to isolate or “lift” the grounds.
Note: The noninverted and inverted signal lines for the
P.I.P. module are connected in parallel with the corre-
sponding lines of the phone jack inputs. The input sig-
nal grounds are not paralleled. Specifically, XLR pins 2
and 3 are connected in parallel with the tip and ring of
the corresponding phone jack. However, pin 1 of the
XLR is not connected in parallel with the sleeve of the
phone jack. This makes it possible for a P.I.P. module
to handle its own signal grounds independently.
1. Turn off the amplifier and disconnect the power
cord from the receptacle.
2. Remove the P.I.P. module.
3. Locate the access hole for the sensitivity switch
inside the chassis opening (see Figure 4.5).
The amplifier’s circuit breaker protects the power sup-
plies from overload. The breaker’s reset switch is lo-
cated on the back panel. Facing the back panel, move
the reset switch the left to disconnect power to the
power supplies, or to the right to reconnect power. If
the circuit breaker trips, the front panel enable indica-
tor will turn off. If this occurs, turn off the enable switch,
flip the reset switch to the right (on), and then turn the
enable switch back on. If it trips again or the amplifier
does not operate properly, contact an authorized ser-
vice center or Crown’s Technical Support Group.
4. Set the switch to the desired position noted on the
access hole label.
5. Replace the P.I.P. module and restore power.
The ground lift switch located on the back panel can
provide isolation between the phone jack input
grounds and the AC (chassis) ground. It does not af-
fect the P.I.P. module’s input connectors. Slide the
SENSITIVITY SWITCH INSIDE ACCESS HOLE
4.5 Filter Cleaning
A dust filter is provided on the amplifier’s air intake (see
Figure 2.1). If this filter becomes clogged, the unit will
not cool as efficiently as it should and high heat sink
temperatures may produce lower-than-normal output.
1.4 V
26 dB
0.775 V
To clean the filter, gently pull it away from the front
panel and wash it with mild dishwashing detergent and
warm water. Be sure the filter is dry before you reinstall
it. Replacement filters may be ordered from the factory.
This amplifier is equipped with a selectable input sensitivity. Remove the P.I.P. module to access the sensitivity switch.
CH-2
CH-1
BALANCED
UNBALANCED
INPUT WIRING
INPUT WIRING
+
TIP
+
TIP
INPUT GROUND LIFT
LIFT
RING
–
GND SLEEVE
GND SLEEVE
(MONO)
(AFFECTS PHONE INPUTS ONLY.)
Dust filters are not 100% efficient—long term this may
require heat sink cleaning by a qualified technician. In-
ternal cleaning information is available from our Tech-
nical Support Group.
GROUND LIFT SWITCH
Fig. 4.5 Input Sensitivity and Ground Lift Switches
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
5 Technical Information
5.1 Overview
Studio Reference amplifiers incorporate several new
technological advancements including real-time com-
puter simulation of output transistor stress, low-stress
output stages, an advanced heat sink embodiment
and the Programmable Input Processor (P.I.P.) expan-
sion system.
The two channels may be used together to double the
voltage (Bridge-Mono) or the current (Parallel-Mono)
presented to the load. This feature gives you the flex-
ibility to maximize power available to the load.
A wide bandwidth, multiloop design is used for state-
of-the-art compensation. This produces ideal behavior
and results in ultra-low distortion values.
Custom circuitry is incorporated to limit temperature
and current to safe levels making it highly reliable and
tolerant of faults. Unlike many lesser amplifiers, it can
operate at its voltage and current limits without self-de-
structing.
Aluminum extrusions are used widely for heat sinks in
power amplifiers due to their low cost and reasonable
performance. However, measured on a watts per
pound or watts per volume basis, the extrusion tech-
nology doesn’t perform nearly as well as the heat sink
technology developed for Studio Reference amplifiers.
Studio Reference amplifiers are protected against all
common hazards that plague high-power amplifiers in-
cluding shorted, open or mismatched loads; over-
loaded power supplies, excessive temperature,
chain-destruction phenomena, input overload and
high-frequency blowups. The unit protects loudspeak-
ers from input and output DC, as well as turn-on and
turn-off transients.
Our heat sinks are fabricated from custom convoluted
fin stock that provides an extremely high ratio of area to
volume, or area to weight. All power devices are
mounted directly to the heat sinks which are also elec-
trically at the Vcc potential. Electrifying the heat sinks
improves thermal performance by eliminating the insu-
lating interface underneath the power devices. The
chassis itself is even used as part of the thermal circuit
to maximize utilization of the available cooling re-
sources.
Real-time computer simulation is used to create an
analogue of the junction temperature of the output tran-
sistors (hereafter referred to as the output devices).
Current is limited only when the device temperature
becomes excessive—and only by the minimum
amount necessary. This patented approach maximizes
the available output power and eliminates overheat-
ing—the major cause of device failure.
5.2 Circuit Theory
Power is provided by low-field toroidal power trans-
former T1. The secondaries of T1 are full-wave rectified
(by D1 through D4, D22 and D24) and filtered by large
computer grade capacitors. A thermal switch embed-
ded in the transformer protects it from overheating.
Monolithic regulators provide a regulated 15 volts.
Crown also invented the four-quadrant topology used
in the output stages of each Studio Reference ampli-
fier (see Figure 5.1). This special circuitry is called
the grounded bridge. It makes full use of the power
supply by delivering peak-to-peak voltages to the load
that are twice the voltage seen by the output devices.
5.2.1 Stereo Operation
For simplicity, the discussion of Stereo operation will
refer to only one channel. Mono operation will be dis-
cussed later. Please refer to the block diagram in Fig-
ure 5.1 and the schematics included with this manual.
As its name suggests, the grounded bridge topology is
referenced to ground. Composite devices are con-
structed to function as gigantic NPN and PNP devices
to handle currents which exceed the limits of available
devices. Each output stage has two composite NPN
and two composite PNP devices.
The input signal at the phone jack passes directly into
the balanced gain stage (U104-A). When a P.I.P. mod-
ule is used, the input signal first passes through the
P.I.P.’s circuitry and then to the balanced gain stage.
The devices connected to the load are referred to as
“high-side NPN and PNP” and the devices connected
to ground are referred to as “low-side NPN and PNP.”
Positive current is delivered to the load by increasing
conductance simultaneously in the high-side NPN and
low-side PNP stage, while synchronously decreasing
conductance of the high-side PNP and low-side NPN.
The balanced gain stage (U104-A) causes balanced to
single-ended conversion using a difference amplifier.
From there, gain can be controlled with the front panel
level controls and the input sensitivity switch. The error
amp (U104-C) amplifies the difference between the
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Fig. 5.1 Circuit Block Diagram
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
output signal and the input signal from the gain pot,
and drives the voltage-translator stage.
DC across the output leads, the DC/low-frequency pro-
tection circuit senses this on the negative feedback
loop and shuts down the power supply until the DC is
removed.
From the error amp, the voltage translator stage chan-
nels the signal to the Last Voltage Amplifiers (LVAs)
depending on the signal polarity. The +LVA (Q104 and
Q105) and the –LVA (Q110 and Q111) drive the fully
complementary output stage with their push-pull effect
through the bias servo Q318.
5.2.2 Bridge-Mono Operation
By setting the back panel stereo/mono switch to
Bridge-Mono, the user can convert the amplifier into a
bridged, single-channel amplifier. With a signal ap-
plied to the channel 1 input jack and the load con-
nected across the two channels’ red (+) 5-way binding
posts, twice the voltage can be output.
The bias servo Q318 is thermally coupled to the heat
sink, and sets the quiescent bias current in the output
stage to lower the distortion in the crossover region of
the output signal.
The channel 1 output feeds the channel 2 error amp
U204-C. Because there is a net inversion, channel 2
output is out of polarity with channel 1. This produces
twice as much voltage across the load. Each channel’s
protection mechanisms work independently if a fault
occurs.
With the voltage swing provided by the LVAs, the sig-
nal then gains current amplification through the triple
Darlington emitter-follower output stage.
The bridge-balanced circuit (U104-D) receives a sig-
nal from the output of the amplifier, and differences it
with the signal at the Vcc supply. The bridge-balanced
circuit then develops a voltage to drive the bridge-bal-
anced output stage. This results in the Vcc supply hav-
ing exactly one half of the output voltage added to its
quiescent voltage. Bias servo Q300 sets the quiescent
current point for the bridge-balanced output stage.
5.2.3 Parallel-Mono Operation
With the stereo/mono switch set to Parallel-Mono, the
output of channel 2 is paralleled with the output of
channel 1. A suitable jumper capable of handling high
current must be connected across the red (+) 5-way
posts to gain the benefits of this mode of operation.
The protection mechanisms that affect the signal path
are implemented to protect the amplifier under real-
world conditions. These conditions are high instanta-
neous current, excessive temperature, and output
device operation outside safe conditions.
The signal path for channel 1 is the same as previously
discussed, except channel 1 also drives the output
stage of channel 2. The channel 2 balanced input, error
amp, translators and LVAs are disconnected and no
longer control the channel 2 output stage. Disconnect-
ing the front-end stages from the channel 2 output
causes the channel 2 IOC circuit to note that the input
waveform (which is not present) does not match the
output waveform (which is driven by the channel 1 in-
put signal). This activates the channel 2 IOC indicator
any time the amplifier is switched into Parallel-Mono
mode. The channel 2 output stage and protection
mechanisms are also coupled through S1 and function
as one.
Q107 and Q108 act as a conventional current limiter,
sensing current in the output stage. When output cur-
rent at any instant exceeds the design criteria, the limit-
ers remove drive from the LVAs, thus limiting current in
the output stage to a safe level.
To further protect the output stages, the patented
ODEP circuitry is used. It produces an analog output
proportional to the always changing safe operating
area of the output transistors. This output controls the
translator stage previously mentioned, removing any
further drive that may exceed the safe operating area
of the output stage.
In Parallel-Mono mode, twice the current of one chan-
nel alone can be obtained. Because the channel 2
ODEP circuit is coupled through S1, this gives added
protection if a fault occurs in the channel 2 output
stage. The ODEP circuit of channel 2 will limit the out-
put of both output stages by removing the drive from
the channel 1 translator stages.
Thermal sensor S100 gives the ODEP circuit vital infor-
mation on the operating temperature of the heat sink on
which the output devices are mounted.
Should the amplifier fail in such a way that would cause
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Power
6 Specifications
Power Bandwidth: (At standard 1 kHz power)
The following applies to units in Stereo mode with 8 ohm loads
and an input sensitivity of 26 dB gain unless otherwise specified.
Studio Reference I : –1 dB from 5 Hz to 27.5 kHz and
–3 dB from 3 Hz to 32.8 kHz.
Studio Reference II: –1 dB from 5 Hz to 28.6 kHz and
Low-Distortion 1 kHz Power: refers to maximum average power
in watts at 1 kHz with 0.02% THD and noise.
–3 dB from 2.3 Hz to 34.4 kHz.
Standard 1 kHz Power: refers to maximum average power in
watts at 1 kHz with 0.1% THD and noise.
Output Power: The following are guaranteed minimums
for low-distortion 1 kHz power from units configured for
120 VAC, 60 Hz power. For more information on power
specifications, see the matrices that follow.
Full Bandwidth Power: refers to maximum average power in
watts from 20 Hz to 20 kHz with 0.1% THD and noise.
Performance
Frequency Response: 0.1 dB 20 Hz to 20 kHz at 1 watt
(see Figure 6.5).
Studio Reference I
Stereo mode (with both channels driven):
1,160 watts into 4 ohms.
780 watts into 8 ohms.
Phase Response: +5 to –15 degrees from 20 Hz to
20 kHz at 1 watt (see Figure 6.8).
Bridge-Mono mode:
Signal-to-Noise: (A-weighted)
2,220 watts into 8 ohms.
1,580 watts into 16 ohms.
Studio Reference I : Greater than 120 dB below rated
full bandwidth power.
Studio Reference II: Greater than 117 dB below rated
full bandwidth power.
Parallel-Mono mode:
2,315 watts into 2 ohms.
1,565 watts into 4 ohms.
Total Harmonic Distortion (THD): Less than 0.02% at
rated low-distortion 1 kHz power. Less than 0.1% at rated
full bandwidth power.
Studio Reference II
Stereo mode (with both channels driven):
555 watts into 4 ohms.
355 watts into 8 ohms.
Intermodulation Distortion (IMD): (60 Hz and 7 kHz 4:1)
Bridge-Mono mode:
Studio Reference I : Less than 0.005% from full band-
width power to 78 watts rising linearly to 0.025% at
78 milliwatts.
1,110 watts into 8 ohms.
715 watts into 16 ohms.
Parallel-Mono mode:
Studio Reference II: Less than 0.005% from full band-
width power to 36 watts rising linearly to 0.025% at
36 milliwatts.
1,115 watts into 2 ohms.
710 watts into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 4
to 8 ohms in Stereo mode, 8 to 16 ohms in Bridge-Mono
mode, and 2 to 4 ohms in Parallel-Mono mode.
Damping Factor: Greater than 20,000 from 10 Hz to
200 Hz, and greater than 2,500 at 1 kHz (see Figure 6.6).
Crosstalk: (At rated full bandwidth power)
Required AC Mains: 50 or 60 Hz; 100, 120, 200, 220 or
240 VAC ( 10%). Both units draw 90 watts or less at idle.
See Section 7 for detailed information on AC power draw,
current draw and thermal dissipation.
Studio Reference I : Better than 100 dB from 20 Hz to
100 Hz falling linearly to better than 70 dB at 20 kHz
(see Figure 6.10).
Studio Reference II : Better than 100 dB from 20 Hz to
100 Hz falling linearly to better than 65 dB at 20 kHz
(see Figure 6.10).
It is extremely important to have adequate AC power for
the amplifier. Power amplifiers cannot create energy—
they must have the required voltage and current to de-
liver the undistorted rated power you expect.
Common Mode Rejection (CMR): (At rated full band-
width power) See Figure 6.9.
Controls
Voltage Gain: (With level controls set for maximum output)
At the 26 dB gain setting, 20:1 3% or 26 dB 0.25 dB.
Enable: A front panel push button used to turn the ampli-
fier on and off.
Studio Reference I : At 0.775 volt sensitivity, 103:1
12% or 40 dB 1 dB; at 1.4 volt sensitivity 57:1 12%
or 35 dB 1 dB.
Studio Reference II: At 0.775 volt sensitivity, 69:1
12% or 37 dB 1 dB; at 1.4 volt sensitivity 38:1 12%
or 32 dB 1 dB.
Level: A front panel rotary potentiometer for each channel
with 31 detents used to control the output level.
Stereo/Mono: A three-position back panel switch used to
select Stereo, Bridge-Mono and Parallel-Mono mode.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Sensitivity: A three-position switch inside the P.I.P. com-
partment used to select the input sensitivity for both chan-
nels: 0.775 or 1.4 volts for standard 1 kHz power, or a 26
dB voltage gain.
Input Sensitivity: Settings include 0.775 volts or 1.4 volts
for standard 1 kHz power, or a 26 dB voltage gain (see
Section 4.4 for more information).
Output Connectors: Two sets of color-coded 5-way
binding posts for each channel (for connecting banana
plugs, spade lugs or bare wire).
Meter On/Off: A two-position switch behind the front
panel used to turn the front panel meters on or off.
Meter Display Mode: A two-position switch behind the
front panel used to set the display mode for the front
panel meters. Display modes include dynamic range of
the output signal in dB or output levels in dB.
Output Impedance: Less than 10 milliohms in series with
2.5 microhenries.
DC Output Offset: (Shorted input) 2 millivolts.
Ground Lift: A two-position back panel switch used to
isolate the input phone jack and AC (chassis) grounds.
Output Signal
Stereo: Unbalanced, two-channel.
Reset: A two-position back panel switch used to reset the
AC mains circuit breaker.
Bridge-Mono: Balanced, single-channel. Channel 1 con-
trols are active; channel 2 should be turned down.
Indicators
Parallel-Mono: Unbalanced, single-channel. Channel 1
controls are active; channel 2 is bypassed.
Enable: This indicator shows the on/off status of the unit’s
low-voltage power supply.
Protection
Signal: Each channel has a signal indicator that flashes
to show audio output.
If unreasonable operating conditions occur, the protec-
tion circuitry limits the drive level to protect the output
stages especially in the case of elevated temperature.
Transformer overheating will result in a temporary shut-
down. Controlled slew-rate voltage amplifiers protect the
unit against RF burnouts. Input overload protection is fur-
nished at the amplifier input to limit current.
IOC: Each channel has an IOC indicator that flashes if the
output waveform differs from the input waveform by 0.05%
or more. The LEDs act as sensitive distortion indicators to
provide proof of distortion-free performance. In Parallel-
Mono mode the channel 2 IOC light stays on.
ODEP: Each channel has an ODEP indicator that shows
the channel’s reserve energy status. Normally, the LEDs
are brightly lit to show that reserve energy is available. In
the rare event that a channel has no reserve, its indicator
will dim in proportion to ODEP limiting. An ODEP indicator
may also turn off under other more unusual circum-
stances (see Section 4.3).
Turn On: The four second turn-on delay prevents dan-
gerous turn-on transients. To change the turn-on delay
time, contact Crown’s Technical Support Group.
Construction
Steel chassis with durable black finish, aluminum front
panel with super-gloss Imron® finish, Lexan overlay, and
a specially designed flow-through ventilation system from
front to side panels.
Dynamic Range/Level Meter: Each channel has a five-
segment meter that displays either the dynamic range of
the output signal in dB or the output level in dB. (From the
factory, the amplifier is set to display dynamic range.) As
dynamic range meters, they show the ratio of the peak to
average power of each channel. As output level meters
they show how high the output levels are relative to stan-
dard 1 kHz power.
Cooling: Convection cooling with assistance from the
computerized, on-demand proportional cooling fan.
Dimensions: Standard 19 inch (48.3 cm) rack mount width
(EIA RS-310-B), 7 inch (17.8 cm) height, 16 inch (40.6 cm)
depth behind mounting surface and 2.75 inch (7 cm) protru-
sion in front of mounting surface.
Input/Output
Input Connector: Two balanced phone jacks on the
back panel and two balanced three-pin XLR connectors
on the factory-installed P.I.P.-FX (see Section 8 for infor-
mation on optional P.I.P. modules).
Approximate Weight: Center of gravity is about 6 inches
(15.2 cm) behind the front mounting surface.
Studio Reference I: 60 pounds, 11 ounces (27.6 kg)
net; 74 pounds, 3 ounces (33.7 kg) shipping weight.
StudioReferenceII:56pounds,2ounces(25.5kg)net;
69 pounds, 10 ounces (31.6 kg) shipping weight.
Input Impedance: Nominally 10 K ohms, balanced.
Nominally 5 K ohms, unbalanced.
Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Crown specifications are guaranteed for three years.
In an effort to provide you with as much information as possible about the high power-producing capabilities of your amplifier,
we have created the following power matrices.
Minimum Guaranteed Power Specifications
Crown’s minimum power specifications represent the absolute smallest amount of output power you can expect from your
amplifier when it is driven to full output under the given conditions. Some spaces in each matrix may be left blank because the
same guarantee is not provided for those conditions—however, your amplifier will perform well under all conditions listed in
each matrix.
When measuring power, 0.1% THD appears to be the industry standard for distortion. Two of the maximum average power
specifications shown in each minimum power matrix are measured at 0.1% THD so you can easily compare Crown specifications
to those of other manufacturers. But this high level of distortion actually allows for some clipping which is undesirable. Because
of this, a maximum average power specification at 0.05% THD is included in each minimum power matrix which represents non-
clipped conditions. Also, power at 0.02% THD is provided in the preceding specifications. Although most manufacturers do not
give power specifications at 0.05% or 0.02% THD, we encourage them to provide these specifications so you will have a more
realistic representation of the way amplifiers should be used in the real world—without a clipped output signal.
Many manufacturers publish power specs with a tolerance of 1 dB or worse. This means their amplifier can deviate more than
20% in output! A 100 watt amplifier would meet their specification if it only produced 79.4 watts. Other manufacturers qualify
their specs by saying they are “typical,” “subject to manufacturing tolerances,” “single channel driven” or that they are specified
with “fuses bypassed.” Each of these statements effectively removes any performance guarantee. In fact, some manufacturers
use these tactics to generate large power numbers, and they don’t even print a disclaimer. We take a different approach at
Crown—our amplifiers are guaranteed to meet or exceed their specifications for three years. Further, because our published
specs are set below our “in-house” mea-
surements, you can expect every Crown
amplifier to exceed its published minimum
power specs. We believe you should get
what you pay for.
Studio Reference I – Minimum Guaranteed Power (Watts)
Maximum Average
FTC Continuous Average
Minimum Power Notes:
0.1% THD+N 0.1% THD+N 0.05% THD+N
0.1% THD + Noise
(See note 4)
Stereo/Mono
Mode
All minimum power specifications are based on
0.5% regulated AC mains with THD of less than
1.0% and an ambient room temperature of 70° F
(21° C). Standard EIA power (RS-490) is not shown
here because it is identical to FTC Continuous
Average Power.
(See note 1)
(See note 2)
(See note 3)
1 kHz
1,190
800
20Hz-20kHz
1,075
1 kHz
1,170
790
1 kHz
20Hz-20kHz
Stereo
(both channels
driven)
4
8
760
785
750
1. A 1 kHz sine wave is presented to the ampli-
fier and the output monitored for nonlinear dis-
tortion. The level is increased until THD
reaches 0.1%. At this point, average power
per channel is reported.
8
2,375
1,595
2,350
1,580
1,095
750
2,150
2,335
1,580
2,320
1,565
1,075
745
Bridge-Mono
(balanced output)
16
2
1,535
1,575
1,565
750
1,490
Parallel-Mono
4
2. A sine wave is presented to the amplifier over
the range from 20 Hz to 20 kHz and the output
monitored for nonlinear distortion. The level at
each frequency is increased until THD reaches
0.1%. At this point, average power per chan-
nel is reported.
Stereo
(both channels
driven)
4
970
725
8
715
8
2,200
1,515
2,185
1,500
1,255
825
1,985
1,440
2,160
1,495
2,175
1,480
1,255
815
Bridge-Mono
(balanced output)
16
2
1,515
1,490
820
1,440
3. A 1 kHz sine wave is presented to the ampli-
fier and the output monitored for nonlinear dis-
tortion. The level is increased until THD
reaches 0.05%. At this point, average power
per channel is reported.
Parallel-Mono
4
Stereo
(both channels
driven)
4
1,135
820
8
795
4. Continuous power in the context of Federal
Trade Commission testing is understood to be
a minimum of five minutes of operation. Har-
monic distortion is measured as the RMS sum
total and given as a percentage of the funda-
mental output voltage. This applies for all watt-
ages greater than 0.25 watts.
8
2,505
1,660
2,485
1,655
2,280
1,610
2,460
1,645
2,475
1,640
Bridge-Mono
(balanced output)
16
2
1,660
1,640
1,595
Parallel-Mono
4
Fig. 6.1 Studio Reference I Minimum Power Matrix
Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Studio Reference II – Minimum Guaranteed Power (Watts)
Maximum Average
FTC Continuous Average
0.1% THD+N 0.1% THD+N 0.05% THD+N
0.1% THD + Noise
(See note 4)
Stereo/Mono
Mode
(See note 1)
(See note 2)
(See note 3)
1 kHz
565
20Hz-20kHz
495
1 kHz
560
1 kHz
20Hz-20kHz
470
Stereo
(both channels
driven)
4
8
555
360
360
340
355
340
8
1,145
720
1,020
690
1,130
715
1,105
720
960
Bridge-Mono
(balanced output)
16
2
680
1,135
715
1,125
715
1,105
715
Parallel-Mono
4
Stereo
(both channels
driven)
4
535
460
330
970
665
525
520
440
320
900
655
8
355
340
345
8
1,080
700
1,070
695
1,045
690
Bridge-Mono
(balanced output)
16
2
1,065
690
1,055
685
1,030
675
Parallel-Mono
4
Stereo
(both channels
driven)
4
595
520
360
585
580
465
355
915
700
8
375
370
375
8
1,205
755
1,060
720
1,195
750
1,145
740
Bridge-Mono
(balanced output)
16
2
1,190
755
1,175
745
1,155
735
Parallel-Mono
4
Fig. 6.2 Studio Reference II Minimum Power Matrix
Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Maximum Power Specifications
Crown’s maximum power specifications represent the largest amount of output power you can expect from your ampli-
fier when it is driven to full output under the given conditions. These specifications can be used to prevent loudspeaker
and hearing damage.
The maximum power matrices include specifications for single cycle and 40 millisecond burst sine waves. Burst signals
act like large transient peaks that are present in common source signals. Loudspeakers can respond to a single cycle
burst, so the single cycle burst specifications should be used to help you protect your loudspeakers. In contrast, a
40 millisecond burst represents the typical response time of the human ear. Your ear will not respond to the entire
dynamic change of a burst that lasts less than 40 milliseconds.
The burst power specifications are provided at 0.05% THD which is a practical low distortion condition. Operating the
amplifier at levels higher than 0.05% THD can result in output power levels that are higher than those listed in the
maximum power matrices.
Maximum Power Notes:
All maximum power specifica-
tions are based on 0.5% regu-
lated AC mains with THD of
Studio Reference I – Maximum Power (Watts)
less than 1.0% and an ambi-
ent room temperature of 70° F
(21° C). Although it is an un-
usual condition, your amplifier
can function well with AC
mains voltages up to 10% over
the specified line voltage. With
overvoltage conditions, your
amplifier may be capable of
delivering instantaneous
power levels up to 20%
greater than the specifications
in the matrix.
Single Cycle Tone Burst
40 Millisecond Tone Burst
0.05% Distortion + Noise
(See note 1)
0.05% Distortion + Noise
(See note 2)
Stereo/Mono
Mode
50 Hz
1 kHz
2,180
1,165
4,355
2,345
4,380
2,340
2,150
1,155
4,285
2,320
4,325
2,320
2,220
1,190
4,360
2,360
4,415
2,355
7 kHz
50 Hz
1 kHz
1,220
820
7 kHz
Stereo
(both channels
driven)
4
8
1,435
900
2,030
1,120
4,080
2,215
4,075
2,230
2,015
1,100
4,020
2,195
3,985
2,190
2,065
1,135
4,090
2,250
4,100
2,240
1,295
835
1,220
830
8
2,855
1,780
2,820
1,795
1,380
900
2,635
1,695
2,605
1,700
1,260
820
2,425
1,635
2,420
1,620
1,135
780
2,400
1,650
2,395
1,650
1,135
790
Bridge-Mono
(balanced output)
16
2
Parallel-Mono
4
1. A single cycle sine wave is
presented to the amplifier
and monitored for nonlinear
distortion. The average
power during the burst is
reported. Loudspeakers
must be able to withstand
this level if they are to be
safely used with this ampli-
fier.
Stereo
(both channels
driven)
4
8
8
2,780
1,740
2,780
1,780
1,470
930
2,595
1,600
2,455
1,620
1,370
880
2,260
1,555
2,250
1,545
1,290
850
2,235
1,570
2,250
1,575
1,275
860
Bridge-Mono
(balanced output)
16
2
Parallel-Mono
4
Stereo
(both channels
driven)
4
2. A 40 millisecond sine wave
burst (10 percent duty cycle)
is presented to the amplifier
and monitored for nonlinear
distortion. Average power
during the burst is reported.
This power level is a mea-
surement of the amplifier’s
maximum transient power
that can be perceived by the
human ear.
8
8
2,945
1,830
2,970
1,810
2,695
1,750
2,715
1,745
2,560
1,685
2,525
1,685
2,505
1,705
2,550
1,700
Bridge-Mono
(balanced output)
16
2
Parallel-Mono
4
Fig. 6.3 Studio Reference I Maximum Power Matrix
Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Studio Reference II – Maximum Power (Watts)
Single Cycle Tone Burst
40 Millisecond Tone Burst
0.05% Distortion + Noise
(See note 1)
0.05% Distortion + Noise
(See note 2)
Stereo/Mono
Mode
50 Hz
1 kHz
875
7 kHz
50 Hz
1 kHz
580
7 kHz
Stereo
(both channels
driven)
4
8
630
395
820
455
605
375
585
375
480
370
8
1,345
800
1,785
970
1,685
935
1,245
750
1,185
755
1,185
770
Bridge-Mono
(balanced output)
16
2
1,330
790
1,770
965
1,670
920
1,205
755
1,170
745
1,170
765
Parallel-Mono
4
Stereo
(both channels
driven)
4
690
905
855
650
610
610
8
405
495
470
385
385
395
8
1,395
830
1,840
1,005
1,830
995
1,750
965
1,315
785
1,230
780
1,240
800
Bridge-Mono
(balanced output)
16
2
1,405
815
1,730
955
1,330
785
1,220
770
1,220
790
Parallel-Mono
4
Stereo
(both channels
driven)
4
650
880
830
595
565
565
8
365
450
430
345
340
350
8
1,305
790
1,775
965
1,715
940
1,195
735
1,130
735
1,150
755
Bridge-Mono
(balanced output)
16
2
1,295
785
1,765
965
1,655
920
1,185
750
1,120
725
1,130
745
Parallel-Mono
4
Fig. 6.4 Studio Reference II Maximum Power Matrix
Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
+2
+1
0
–1
–2
–3
–4
1 watt
8 ohm
4 ohm
dB
–5
–6
–7
10
100
1 K
10 K
100 K
FREQUENCY (Hz)
Fig. 6.5 Typical Frequency Response
100,000
10,000
DAMPING
1,000
100
10
8 ohm
20
100
1 K
10 K
20 K
FREQUENCY (Hz)
Fig. 6.6 Typical Damping Factor
1
0.1
8 ohm
OHMS
0.01
0.001
0.0001
20
100
1 K
10 K
20 K
FREQUENCY (Hz)
Fig. 6.7 Typical Output Impedance
Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
+135˚
+90˚
+45˚
0˚
–45˚
–90˚
–135˚
20
100
1 K
10 K
20 K
FREQUENCY (Hz)
Fig. 6.8 Typical Phase Response
0
–20
–40
dB –60
–80
–100
–120
20
100
1 K
10 K
20 K
FREQUENCY (Hz)
Fig. 6.9 Typical Common Mode Rejection
Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
0
–20
–40
dB –60
–80
Studio Reference II
Studio Reference I
–100
–120
20
100
1 K
10 K
20 K
FREQUENCY (Hz)
Fig. 6.10 Typical Crosstalk
Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
7 AC Power Draw and
Thermal Dissipation
This section provides detailed information about the
amount of power and current drawn from the AC mains
by Studio Reference amplifiers and the amount of heat
produced under various conditions. The calculations
presented here are intended to provide a very realistic
and reliable depiction of the amplifiers. The following
assumptions were made:
Here are the equations used to calculate the data pre-
sented in Figures 7.1 and 7.2:
The estimated quiescent power draw of 90 watts is a
maximum figure, and assumes the fan is running at
high speed. The following equation converts power
draw in watts to current draw in amperes:
• The amplifier’s available channels are loaded, and
full, standard 1 kHz power is being delivered.
AC Mains Power
Draw (watts)
• Amplifier efficiency at standard 1 kHz power is
estimated to be 65%.
Current Draw
=
(amperes)
AC Mains
Voltage
Power
Factor (.83)
x
• Quiescent power draw is 90 watts (an almost
negligible amount for full-power calculations).
The power factor constant of 0.83 is needed to
compensate for the difference in phase between in the
AC mains voltage and current. The following equation
was used to calculate thermal dissipation:
• Quiescent thermal dissipation equals 307 btu/hr at
90 watts.
• Duty cycle takes into account the typical crest factor
for a particular type of source material.
Total output power with all Duty
Thermal
Dissipation =
(btu/hr)
.35
x
x
Quiescent Power
Draw (90 watts)
channels driven (watts)
Cycle
x
3.415
+
(
)
Amplifier Efficiency (.65)
• Duty cycle of pink noise is 50%.
The constant 0.35 is inefficiency (1.00 – 0.65) and the
factor 3.415 converts watts to btu/hr. Thermal dissipa-
tion in btu is divided by the constant 3.968 to get kcal. If
you plan to measure output power under real-world
conditions, the following equation may be helpful:
• Duty cycle of highly compressed rock ‘n’ roll
midrange is 40%.
• Duty cycle of uncompressed rock ‘n’ roll is 30%.
• Duty cycle of background music is 20%.
• Duty cycle of continuous speech is 10%.
• Duty cycle of infrequent paging is 1%.
Total output power with all
channels driven (watts)
Duty
Thermal
Dissipation =
(btu/hr)
.35
x
x
Quiescent Power
Draw (90 watts)
Cycle
x
3.415
+
(
)
Amplifier Efficiency (.65)
Studio Reference I
L O A D
8 Ohm Stereo / 16 Ohm Bridge-Mono / 4 Ohm Parallel-Mono
4 Ohm Stereo / 8 Ohm Bridge-Mono / 2 Ohm Parallel-Mono
AC Mains
Power
AC Mains
Power
Current Draw (Amps) Thermal Dissipation
Current Draw (Amps) Thermal Dissipation
Duty
Cycle
Draw
Draw
100-120 V 220-240 V btu/hr
kcal/hr
100-120 V 220-240 V btu/hr
kcal/hr
(Watts)
(Watts)
50%
40%
30%
20%
10%
1325
1075
830
15.9
12.9
10.0
7.0
7.2
5.9
4.5
3.2
1.8
1,780
1,485
1,190
900
450
375
300
230
155
1,925
1,555
1,190
825
23.1
18.7
14.3
9.9
10.5
8.5
6.5
4.5
2.5
2,500
2,060
1,620
1,185
745
630
520
410
300
190
585
340
4.1
605
460
5.5
Fig. 7.1 Studio Reference I Power Draw, Current Draw and
Thermal Dissipation at Various Duty Cycles
Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
Studio Reference II
L O A D
8 Ohm Stereo / 16 Ohm Bridge-Mono / 4 Ohm Parallel-Mono 4 Ohm Stereo / 8 Ohm Bridge-Mono / 2 Ohm Parallel-Mono
AC Mains
Power
AC Mains
Power
Current Draw (Amps) Thermal Dissipation
Current Draw (Amps) Thermal Dissipation
Duty
Cycle
Draw
Draw
100-120 V 220-240 V btu/hr
kcal/hr
100-120 V 220-240 V btu/hr
kcal/hr
(Watts)
(Watts)
50%
40%
30%
20%
10%
645
535
425
315
205
7.8
6.4
5.1
3.8
2.4
3.5
2.9
2.3
1.7
1.1
970
840
705
575
440
245
215
180
145
115
975
795
620
445
270
11.7
9.6
7.5
5.3
3.2
5.3
4.4
3.4
2.4
1.5
1,360
1,150
940
345
290
240
185
135
730
520
Fig. 7.2 Studio Reference II Power Draw, Current Draw and
Thermal Dissipation at Various Duty Cycles
Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
8 Accessories
8.1 P.I.P. Modules
One advantage of Studio Reference amplifiers is the
ability to customize them using P.I.P. (Programmable In-
put Processor) modules. Each amplifier is equipped with
an edge card connector inside the back panel P.I.P.
compartment. The modules install easily:
compressors activate when a signal will clip the input,
an IOC error occurs, or the output exceeds the selected
threshold. The subsonic filters have corner frequencies
of 24, 28, 32 and 36 Hz.
CH-2 INPUT
CH-1 INPUT
FTE
+
–
+
–
L
IE
E
N
A
P
K
C
A
B
R
IF
L
P
M
A
F
O
Programmable
Input Processor (P.I.P.)
.
P
U
.
D
I
.
P
O
E
L
M
P.I.P.-FTE includes all P.I.P.-FXT features, and adds
12 dB/octave RFI filters, variable 18 dB/octave high-pass
filters, and 6 dB/octave 3 kHz shelving networks for “con-
stant-directivity” horn equalization. Screw terminal plugs
are provided for input.
Fig. 8.1 Installing a P.I.P. Module
WARNING: Disconnect power to the amplifier when in-
stalling or removing a P.I.P. module.
IQ-P.I.P.-AP integrates the amplifier into Crown’s pat-
ented IQ System.® The IQ System provides centralized
computer control of 1 to 2,000 amplifiers. Each ampli-
fier channel can be monitored and controlled from an
inexpensive personal computer. Any combination of mic-
and line-level signals can also be mixed and routed with
optional MPX-6,™ SMX-6™ and AMB-5™ mixer/multiplex-
ers, and the MRX series matrixers.
Here are some of the available P.I.P. modules:
AMC
3
OUTPUT
INPUT
Programmable
Input Processor (P.I.P.)
GND
1
2
IQ-P.I.P.-AP Smart Amp™ offers the monitoring and
control features of the IQ-P.I.P.-AP plus the ability to
function as a stand-alone unit as part of the IQ
System’s distributed intelligence.™ Features include a
smooth output limiter for transparent loudspeaker pro-
tection, power supply gates for energy savings, ODEP
conservation which protects the output devices with
precision input signal control, interrupt-driven report-
ing that lets you define error conditions, and config-
urable short detection.
P.I.P.-AMCb unites many features of the P.I.P.-XOV and
P.I.P.-CLP. It offers a variable 4th-order Linkwitz-Riley
crossover and an IOC-driven, variable threshold com-
pressor. In addition, it provides “constant-directivity” horn
equalization and filter-assisted B6 vented box equaliza-
tion. Biamping and triamping capabilities are provided
via XLR connectors.
CH-2
CH-1
b
EDC
CH-2
CH-1
CLP
P U S H
P U S H
3
Programmable
Input Processor (P.I.P.)
INPUT
INPUT
GND
1
2
P U S H
P U S H
3
Programmable
Input Processor (P.I.P.)
INPUT
INPUT
GND
1
2
P.I.P.-EDCb combines a sophisticated error-driven com-
pressor and smooth limiter with a subsonic filter for each
channel. The compressors have adjustable attack and
release times, and can be set to track each other. The
P.I.P.-CLP is designed to detect and prevent overload.
Its compressor is driven by the amplifier’s built-in IOC
error detection circuitry. Unlike typical signal-driven com-
Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
pressors, it only compresses the signal to prevent over-
load. It can deliver up to 13 dB of additional headroom
without being noticeable.
PA
–
+
–
+
CH-2
CH-1
–
+
–
+
MIC
LEVEL
MIC
LEVEL
LINE
MIC
REMOTE
MIC
LINE
C H - 2 I N P U T S
C H - 1 I N P U T S
CH-2 INPUT
CH-1 INPUT
ISO
Programmable
Input Processor (P.I.P.)
+
–
+
–
—WARNING—
THIS P.I.P. PROVIDES FULL ISOLATION
FOR ISO-MODIFIED AMPLIFIERS ONLY!
DO NOT CONNECT THE OUTPUT GROUND
LUG TO THE INPUT COMMON OR CHASSIS
GROUND. REFER TO P.I.P.–ISO OWNER’S
MANUAL FOR FURTHER INFORMATION.
P.I.P.-PA adds a switchable balanced low-impedance
mic input, a balanced line-level input and a compressor
to each channel. Remote switching circuitry provides
quick and quiet fades from mic to line and back.
Programmable
Input Processor (P.I.P.)
P.I.P.-ISO is designed especially for 25 to 140 volt dis-
tributed systems where UL®-listed isolation is required.
Installation requires minor amplifier modifications. With
the P.I.P.-ISO installed, the amplifier outputs are safely
isolated from the input terminals and the chassis.
P.I.P.-102 is a two-channel module providing equaliza-
tion based on the BOSE® 102 controller. Screw terminal
plugs provide balanced connections. Each input chan-
nel has an output from the P.I.P. that can be indepen-
dently configured for output with no processing, 102
equalization or 102 equalization with bass-cut.
C H - 2 I N P U T
–
C H - 1 I N P U T
ATN+
ATTENUATION
ATTENUATION
+
–
16
16
14
14
12
20
20
12
24
30
36
44
52
24
30
36
44
52
10
8
10
8
6
RPA
CH-2
CH-1
6
4
4
2
2
60
60
0
0
dB
dB
A U D I O B U S
Programmable
Input Processor (P.I.P.)
INPUT D
(CH-2)
INPUT C
(CH-2)
INPUT A
(CH-1)
INPUT B
(CH-1)
LEVEL
LEVEL
Programmable
Input Processor
P.I.P.-ATN includes all P.I.P.-FTE features, plus a 32-step
+
– +
–
+
– +
–
precision attenuator for each channel.
P.I.P.-RPA adds the features of a 4x2 mixer to your am-
plifier. Its four inputs accept mic- or line-level input. It
offers priority switching (“voice-over”) of each input and
remote level control with the RPA-RMT. Other features
include bus inputs and outputs, adjustable input sensi-
tivity, phantom power and RFI suppression. Input isola-
tion transformers are optional.
+
RING
TIP
XOV
–
GND
SLEEVE
P U S H
I N PU T S
3
O U T PU T S
Programmable
Input Processor (P.I.P.)
GND
1
2
P.I.P.-XOV is a versatile 18 dB/octave mono crossover/
filter with biamping and triamping capabilities.
For more information on these P.I.P.s or other P.I.P.s un-
der development, contact your local dealer or Crown’s
Technical Support Group.
P.I.P.-FMX facilitates “daisy-chaining” balanced ampli-
fier inputs. Female to male three-pin XLR connectors
are used to passively bridge the inputs.
P.I.P.-FXQ makes it easy to connect audio sources that
have phono (RCA) connectors. It includes two balanced
three-pin female XLR connectors, and two female phono
jacks for quasi-balanced or unbalanced operation.
C H - 2
C H - 1
FXT
P U S H
P U S H
3
Programmable
Input Processor (P.I.P.)
I N P U T
I N P U T
GND
1
2
P.I.P.-FXT uses balanced 1:1 transformers to isolate the
amplifier from the input signal. It has balanced female
three-pin XLR connectors.
Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
Studio Reference
I
&
I
I
Professional Studio Amplifiers
9.2.2 Factory Service
9 Service
To obtain factory service, fill out the service information
page that follows and send it along with your proof of
purchase and the defective unit to the Crown factory.
For warranty service, we will pay for ground shipping
both ways in the United States after receiving copies of
the shipping receipts. Shipments should be sent “UPS
ground.” (If the unit is under warranty, you may send it
C.O.D. for the cost of freight via UPS ground.) The fac-
tory will return it via UPS ground. Please contact us if
other arrangements are required.
This unit has very sophisticated circuitry which should
only be serviced by a fully trained technician. This is
one reason why each unit bears the following label:
CAUTION: To prevent electric shock, do not remove
covers. No user serviceable parts inside. Refer servic-
ing to a qualified technician.
9.1 Worldwide Service
Service may be obtained from an authorized service
center. (Contact your local Crown/Amcron representa-
tive or our office for a list of authorized service centers.)
To obtain service, simply present the bill of sale as
proof of purchase along with the defective unit to an
authorized service center. They will handle the neces-
sary paperwork and repair.
Always use the
original factory pack
to transport the unit.
Factory Service Shipping Instructions:
1. When sending a Crown product to the factory for
service, be sure to fill out the service information
form that follows and enclose it inside your unit’s
shipping pack. Do not send the service information
form separately.
Remember to transport your unit in the original factory
pack. We will pay the surface shipping costs both
ways for warranty service to the authorized service
center nearest you after receiving copies of all ship-
ping receipts. You must bear the expense of all taxes,
duties, and customs fees when transporting the unit.
2. To ensure the safe transportation of your unit to the
factory, ship it in an original factory packing con-
tainer. If you don’t have one, call or write Crown’s
Parts Department. With the exception of polyure-
thane or wooden crates, any other packing material
will not be sufficient to withstand the stress of ship-
ping. Do not use loose, small size packing materi-
als.
9.2 North American Service
Service may be obtained in one of two ways: from an
authorized service center or from the factory. You may
choose either. It is important that you have your copy of
the bill of sale as your proof of purchase.
9.2.1 Service at a North American Service Center
3. Do not ship the unit in any kind of cabinet (wood or
metal). Ignoring this warning may result in extensive
damage to the unit and the cabinet. Accessories
are not needed—do not send the instruction
manual, cables and other hardware.
This method usually saves the most time and effort.
Simply present your bill of sale along with the defective
unit to an authorized service center to obtain service.
They will handle the necessary paperwork and repair.
Remember to transport the unit in the original factory
pack. A list of authorized service centers in your area
can be obtained from our Technical Support Group.
If you have any questions, please call or write the
Crown Technical Support Group.
Crown Audio Division
Tech. Support / Factory Service
57620 C.R. 105
Elkhart, Indiana 46517 U.S.A.
Phone: 1-219-294-8200
U.S.: 1-800-342-6939
Fax: 1-219-294-8301
Page 40
Download from Www.Somanuals.com. All Manuals Search And Download.
Crown Factory Service Information
Shipping Address: Crown International, Inc., Factory Service, 57620 C.R. 105, Elkhart, Indiana 46517
Phone: 1-800-342-6939 or 1-219-294-8200 Fax: 1-219-294-8301
Owner’s Name: _________________________________________________________________________
Shipping Address: ______________________________________________________________________
Phone Number: ________________________________________________________________________
Model: ________________________ Serial Number:______________ Purchase Date: ___________
NATURE OF PROBLEM
(Be sure to describe the conditions that existed when the problem occurred and what attempts were made to correct it.)
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
Other equipment in your system: _________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
If warranty has expired, payment will be: ꢀ Cash/Check
ꢀ VISA
ꢀ MasterCard
ꢀ C.O.D.
Card Number:___________________________ Exp. Date:_______
Signature:_____________________________
ENCLOSE THIS PORTION WITH THE UNIT. DO NOT MAIL SEPARATELY.
Download from Www.Somanuals.com. All Manuals Search And Download.
|