Crosley®
LAUNDRY CENTER
Owner's Guide
LAVADORA Y SECADORA
SUPERPUESTAS
Manual Del Usuario
PN 134857400A (0712)
Download from Www.Somanuals.com. All Manuals Search And Download.
GAS LAUNDRY CENTERS:
Do not use or mix liquid
chlorine bleach with other household
chemicals such as toilet cleaners, rust
removers, acid or products containing
ammonia. These mixtures can produce
dangerous fumes which can cause serious
injury or death.
Do not under
any circumstances
cut, remove,
Avoid fire
hazard or electrical shock. Do
not use an adaptor plug or
extension cord or remove
groundingprongfromelectrical
power cord. Failure to follow
thiswarningcancauseserious
injury, fire or death.
Grounding type
wall receptacle
or bypass
thegroundingprong
from this plug
Power supply cord with
3-pronggroundingplug
CORRECT
Use this way ONLY
Important Safety Instructions
Read all instructions before using this laundry center.
You can be killed or seriously injured if you don't follow these Important Safety Instructions:
• To reduce the risk of fire, electrical shock, or injury to persons when using this laundry center, comply with the basic warnings
listed below.
• Failure to comply with these warnings could result in serious personal injuries.
Prevent Fire
• Do not wash or dry items that have been previously cleaned in, soaked in, or spotted with gasoline, cleaning solvents, kerosene,
waxes, etc. Do not store these items on or near the dryer. These substances give off vapors that could ignite or explode.
• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical
reaction that could cause a load to catch fire.
• Do not put oily or greasy rags or clothing on top of the laundry center. These substances give off vapors that could ignite the
materials.
• Do not add gasoline, cleaning solvents, or other flammable or explosive substances to the wash water. These substances give
off vapors that could ignite or explode.
• Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more.
HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washer, turn
on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas.
Hydrogen gas is flammable; do not smoke or use an open flame during this time.
• To prevent fire, do not use heat to dry items containing plastic, foam rubber or similarly textured rubber-like materials, or items
containing feathers or down. Use Air Fluff (No Heat) only.
• Clean the dryer lint screen before or after each load. The interior of the dryer, lint screen housing and exhaust duct should be
cleaned approximately every 18 months by qualified service personnel. An excessive amount of lint build-up in these areas could
result in inefficient drying and possible fire. See Care and Cleaning.
• Do not operate the dryer if the lint screen is blocked, damaged or missing. Fire hazard, overheating and damage to fabrics can
occur. If your dryer has a drying rack, always replace the lint screen when finished using the drying rack.
• Keep area around the exhaust opening and surrounding areas free from the accumulation of lint, dust and dirt.
• Do not obstruct the flow of ventilating air. Do not stack or place laundry or throw rugs against the front or back of the laundry
center.
• Do not spray any type of aerosol into, on or near laundry center at any time.
• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or
product.
• Failure to comply with these warnings could result in fire, explosion, serious bodily injury and/or damage to the rubber or plastic
parts of the laundry center.
Protect Children
• Do not allow children to play on or in the laundry center. Close supervision of children is necessary when the laundry center is
used near children. As children grow, teach them the proper, safe use of all appliances.
• Destroy the carton, plastic bag and other packing materials after the laundry center is unpacked. Children might use them for
play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers.
• Keep laundry products out of children's reach. To prevent personal injury, observe all warnings on product labels.
• Before the laundry center is removed from service or discarded, remove the washer lid and dryer door to prevent accidental
entrapment.
• Failure to comply with these warnings could result in serious personal injuries.
Prevent Injury
• To prevent shock hazard and assure stability during operation, the laundry center must be installed and electrically grounded
by a qualified service person in accordance with local codes. Installation instructions are packed in the laundry center for the
installer's reference. Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures. If the laundry center is moved
to a new location, have it checked and reinstalled by a qualified service person.
• To prevent personal injury or damage to the laundry center, the electrical power cord of a gas laundry center must be plugged into
a properly grounded system. Never ground the laundry center to a gas pipe. Do not use an extension cord or an adaptor
3
Printed in U.S.A.
plug.
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions Con't
• Follow package directions when using laundry products. Incorrect usage can produce poisonous gas--resulting in serious injury
or death.
- Do not combine laundry products for use in 1 load unless specified on the label.
- Do not mix chlorine bleach with ammonia or acids such as vinegar.
Washing Procedures
•
•
•
Follow the guidelines below for preparing the wash load.
Read the Washer Operating Instructions for operating your specific model.
Always read and follow fabric care and laundry product labels.
To reduce the risk of fire, electrical shock, or injury to persons, read
Important Safety Instructions before operating this washer.
1. Sort laundry into loads that can be washed together.
Sort items by recommended water temperatures, wash time, and agitate/spin
speeds.
•
•
Separate white, light, and colorfast items from dark and noncolorfast items.
Separateitemswhichshedlintfromitemswhichattractlint.Permanentpress,
synthetic, knit and corduroy items will pick up lint from towels, rugs and
chenille bedspreads.
Sort laundry into loads that can be
washed together.
•
•
Separate heavily soiled items from lightly soiled items.
Separate lacy, sheer and loosely knit items from sturdy items.
2. Prepare items for washing.
•
•
•
Empty pockets.
Brush off lint and dirt. Shake out rugs and beach towels.
Close zippers, fasten hooks, tie strings and sashes, and remove nonwashable
trims and ornaments.
•
Removepins,decorativebuttons,beltbuckles,andotherobjectswhichcould
be damaged. This also helps protect other items in the wash load.
Mend rips and tears to prevent further damage during washing.
Place delicate items such as bras, shoulder pads, hosiery, and belts in a mesh
bag to prevent tangling during the wash cycle.
•
•
Empty pockets.
•
Turn knit items inside out to prevent pilling.
3. Pretreat stains and heavy soil.
See Stain Removal for details.
4. Add a measured amount of detergent to the wash tub before
adding the laundry load.
Followdetergentmanufacturer'sdirections.Theamountrequireddependsontype
of detergent, load size and soil level, and water hardness.
5. If desired, add liquid bleach to Bleach Dispenser (available on
some models).
Place delicate items in a mesh bag.
•
Before adding the wash load, add liquid bleach to bleach dispenser located in
left front corner under the lid:
•
•
•
3/4 cup (180 ml) for small loads
1 cup (240 ml) for large loads
1-1/4 cups (300 ml) for extra-large loads.
•
•
Then add 1 cup (240 ml) water to flush the dispenser.
Do not use powdered bleach in the bleach dispenser. Add powdered bleach
to the empty tub.
For models without a bleach dispenser, dilute the recommended amount of
liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after
Bleach Dispenser (some models)
a few minutes of agitation. Do not pour bleach directly on wash load.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Procedures
(continued)
6. Add laundry load to washer.
•
Dry load level should not be higher than the top of agitator vanes.
Do not overload the washer.
•
•
Donotputitemsontopofagitatororwrapthemaroundit.Loaditemsevenly.
Combine large and small items in a load. Load large items first. Large items
should not be more than half the total wash load.
•
When washing a single heavy item, add 1 or 2 towels to balance the load.
Do not load items higher than top of
agitator vanes.
7. If desired, add liquid fabric softener to Fabric Softener
Dispenser (available on some models).
For models with a built-in dispenser (see picture to the left):
1. Addliquidsoftenertothedispenser,followingfabricsoftenerlabeldirections.
2. Add water to bring liquid level to fill line on dispenser cap.
3. Removethedispenserfromtheagitatoraftereachuse.Rinsebothcapandcup
with warm water. Replace dispenser in the agitator.
NOTE: To separate cap from cup, put thumb into dispenser and push against side
of cup (see picture to the left). After cleaning, push cap and cup firmly together.
Replace dispenser by lining up the ribs and grooves and snapping it into position.
Iffabricsoftenerbuildsupinoraroundthedispenser,cleantheareawithhotwater.
DO NOT REMOVE SERVICE CAP FOUND INSIDE THE AGITATOR POST.
Built-In Fabric Softener Dispenser
(some models)
For models without a fabric softener dispenser, follow fabric softener label
directions. Add diluted fabric softener to the final rinse. Do not pour fabric
softener directly on the wash load.
8. Select cycle and settings according to type, size, and soil level
of each load .
See Operating Instructions for your specific model controls.
9. Start the washer.
Close the washer lid and pull out the cycle selector knob. The washer will not
agitate or spin with the lid open.
Built-In Fabric Softener Dispenser
(some models)
•
•
To stop the washer, push in the cycle selector knob.
To change a cycle, push in the cycle selector knob. Turn it clockwise to the
desired setting. Pull out the knob to restart the washer.
10.Remove items when the cycle is completed.
For your safety, the lid locks when the tub is spinning. It will remain locked for 2-
3 minutes after the tub stops spinning.
•
To open the lid during a spin, push in the cycle selector knob and wait about
2-3 minutes for the lid lock to release. Do not force open the locked lid.
Place washed items in automatic dryer, line dry, or dry flat as directed by fabric
carelabel.Excesswrinkling,colortransferorodorsmaydevelopinitemsleftinthe
washer after the cycle has ended.
Toavoidseriouspersonalinjury,donotoperatewasherifsafetylidlock
is missing or damaged.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Safe Stain Removal Procedures
To reduce the risk of fire, electrical shock, or serious injury to persons or
property, comply with the basic warnings listed in Important Safety Instructions and
those listed below.
•
•
•
•
Read and comply with all instructions on stain removal products.
Keep products in their original labeled containers and out of children's reach.
Thoroughly wash any utensils used.
Do not combine stain removal products, especially ammonia and chlorine
bleach. Dangerous fumes may result.
Never wash items which have been previously cleaned in, washed in, soaked
in or spotted with gasoline, dry cleaning solvents or other flammable or
explosive substances because they give off vapors that could ignite or explode.
Never use highly flammable solvents, such as gasoline, inside the home.
Vapors can explode on contact with flames or sparks.
•
•
Do not combine stain removal products.
For successful stain removal:
•
•
Remove stains promptly.
Determine the kind of stain, then follow recommended treatment in the stain
removal chart on the next page.
•
To pretreat stains, use a prewash product, liquid detergent, or a paste made
from granular detergent and water.
•
•
•
•
Use cold water on unknown stains because hot water can set some stains.
Check label instructions for treatments to avoid on specific fabrics.
Check for colorfastness by testing stain remover on an inside seam.
Rinse and wash items after stain removal.
Follow fabric care label instructions.
Stain Removal
STAIN
Adhesive tape, chewing
gum, rubber cement
TREATMENT
Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
nonflammable dry cleaning fluid.
Baby formula, dairy
products, egg
Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.
Beverages (coffee, tea,
soda,juice, alcoholic
beverages)
Pretreat stain. Wash using cold water and bleach safe for fabric.
Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using
bleach safe for fabric.
Blood
Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is
absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable
dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
Candle wax, crayon
Chocolate
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Pretreat with prewash stain remover or rub with bar soap.
Collar or cuff soil, cosmetics
Dye transfer on white
Use packaged color remover. Wash using bleach safe for fabric.
fabric
Grass
Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.
Grease, oil, tar (butter, fats,
salad dressing, cooking oils,
car grease, motor oils)
Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash
using hottest water safe for fabric.
Ink
Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
alcohol or nonflammable dry cleaning fluid.
Mildew, scorch
Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly
mildewed fabrics may be permanently damaged.
Mud
Brush off dry mud. Pretreat or soak with product containing enzymes.
Pretreat with prewash stain remover. Wash using bleach safe for fabric.
Mustard, tomato
Nail polish
May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
Paint, varnish
Perspiration
WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL
BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.
Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for
fabric.
Rust, brown or yellow
discoloration
For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and
nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
Shoe polish
LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat
with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.
Wash using bleach safe for fabric.
Urine, vomit, mucus, feces
Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.
Download from Www.Somanuals.com. All Manuals Search And Download.
Common Washing Problems
Manywashingproblemsinvolvepoorsoilandstainremoval,residuesoflintandscum,andfabricdamage.Forsatisfactorywashing
results, follow these suggestions provided by The Soap and Detergent Association.
SOLUTIONS
PROBLEM
PREVENTIVE MEASURES
•Add detergent before wash load. Then
start washer.
•Dilute fabric softener with water.
•Add fabric softener to dispenser
(available on some models).
POSSIBLE CAUSES
•Detergent or liquid fabric softener
did not dissolve or disperse.
•If caused by detergent, mix 1 cup (240
ml) white vinegar with 1 quart (.95 L)
water in a plastic container. Soak item 1
hour. Rinse.
•If caused by fabric softener, rub stains
with bar soap. Wash.
Blue stains
•Sort items by soil level and color.
•Use correct amount of detergent, hottest
water and bleach safe for fabric
•Use correct amount of detergent and
hottest water safe for fabric.
•Do not pour liquid fabric softener
directly on fabric. See package
directions or Washing Procedures for
proper diluting.
•Rewash with correct amount of
detergent and hottest water safe for
fabric. Add bleach safe for fabric.
•Treat with prewash stain remover or
liquid detergent.
•Increase detergent and water
temperature. Rewash.
•Rub fabric softener stains with bar
soap.
•Not enough detergent.
•Wash water temperature too
low.
Discoloration,
graying
•Incorrect sorting.
•Not enough detergent.
•Undiluted liquid fabric softener
poured directly on fabric.
Greasy, oily stains
•Never pour chlorine bleach directly on
fabric.
•Check condition of items before washing.
See Washing Procedures for preparing
and loading the wash load.
•May be irreversible if rips, tears and
seams cannot be mended.
•Incorrect use of chlorine bleach.
•Unfastened zippers, hooks,
buckles.
•Rips, tears and broken threads.
•Overloading the washer.
•Degradation of fabric.
Holes, tears, or
snags
•See Washing Procedures for sorting
and preparing the wash load.
•Do not overload washer.
•Use correct cycle, amount of detergent,
water temperature and water level.
•Reduce load size. Rewash using correct
water temperature, water level, and
amount of detergent.
•Add nonprecipitating water conditioner
to wash water.
•Add liquid fabric softener to final rinse.
•Dry load in dryer.
•Remove lint with lint brush or roller.
•Incorrect sorting.
•Tissues left in pocket.
•Overloading the washer.
•Not enough detergent.
•Undissolved detergent has left
residue.
Lint
•Static cling is attracting lint.
•Load washed too long
•Use fabric softener in the washer to
lubricate fibers.
•When ironing, use spray starch or fabric
finish on collars and cuffs.
•Use a lint brush or shaver to remove
pills.
•Pilling is normal with synthetic
and permanent press fabrics.
This is due to abrasion from
normal wear.
Pilling
(Fibers break off,
ball up and cling to
fabric)
•Turn items inside out to reduce abrasion.
•Increase water temperature using hottest
water safe for fabric.
•Do not overload washer.
•Use liquid detergent or use
nonprecipitating water conditioner with
granular detergent.
•Reduce load size.
•Add dissolved detergent to tub . Rewash
load.
•Mix 1 cup (240 ml) white vinegar to 1
gallon (3.8 L) warm water in plastic
container. Soak item. Rinse and rewash.
•Undissolved detergent.
•Some granular detergents can
combine with hard water
minerals to form a residue.
Residue or powder
on dark items;
Stiff, harsh fabrics.
•Do not overload washer.
•Remove items from washer as soon as
cycle is completed.
•Reduce load size.
•Rinse in cold water with liquid fabric
softener.
•Overloading the washer.
Wrinkling
•Use liquid fabric softener.
•Wash synthetics frequently using water
at least 100°F (37°C ) and correct water
level.
•Soak in detergent booster or product
containing enzymes.
•Wash in hot water using full permanent
press cycle.
•Agitation time too short.
•Wash water temperature too
low.
Yellow buildup of
body soil on
synthetic fabrics
•Not enough detergent.
•Increase detergent dosage.
•Add bleach safe for fabric.
•Or, treat with color remover.
•Use nonprecipitating water softener.
•Before washing, run hot water for a few
minutes to clear lines.
•Drain water heater occasionally.
•For an ongoing problem, install an iron
filter in your water supply system.
•To restore discolored load of whites,
use rust remover safe for fabric.
Do not use chlorine bleach to remove
rust stains. It may intensify
discoloration.
•Iron or manganese in water
supply, water pipes, or water
heater.
Yellow or brown
rust stains
7
Download from Www.Somanuals.com. All Manuals Search And Download.
• Follow the guidelines below for preparing the load for drying.
Drying Procedures
• Read the Dryer Operating Instructions for operating your specific model.
• Always read and follow fabric care labels and laundry product labels.
Toreducetheriskoffire, electricalshock, orseriousinjurytopersons
orproperty,complywiththebasicwarningslistedin ImportantSafetyInstructions
and those listed below.
1. Prepare items for drying.
•
Dry items of similar fabric, weight and construction in the same load.
•
Separate dark items from light-colored items. Separate items that shed lint
from those that attract lint. If an item sheds lint, turn it inside out.
•
Besurebuckles,buttonsandtrimareheatproofandwon'tdamagethedrum
finish.Closezippers,fastenhooksandVelcro®-likefasteners.Tiestringsand
sashes to prevent snagging and tangling.
•
•
If possible, turn pockets inside out for even drying.
Check for stains which may not have been removed in washing. Dryer heat
may permanently set some stains. Repeat stain removal process before
drying.
Follow fabric care label instructions.
•
Place small items in a mesh bag to prevent tangling and for easy removal.
2. Check that lint screen is clean and in place.
3. Load the dryer.
•
•
•
•
•
Theaverageloadwillfillthedrum1/3to1/2full.Itemsneedroomtotumble
freely for even drying and less wrinkling. Do not overload dryer.
Whendryinglargeitems,dryonly2or3atatime.Fillouttheloadwithsmall
and medium sized items.
For delicate or very small loads, add 2 lint-free towels for better drying, less
wrinkling, and to prevent grease stains caused by fabric softener sheets.
Place small items in a mesh bag.
Donotoverdryitems.Overdryingcancausewrinkling,shrinkage,harshness,
and a build-up of static electricity, which can produce more lint.
If desired, add a dryer fabric softener sheet.
4. Close the dryer door and set dryer controls (some models).
See Dryer Operating Instructions card for your specific model controls.
5. Turn cycle selector clockwise to the desired setting.
6. Start the dryer.
•
Turn Start control clockwise to ON. Hold for 1-2 seconds and release.
•
Toaddorremoveitemswhenthedryerisrunning,openthedoor.Thedryer
will always stop when the door is opened.
•
Allow the drum to come to a complete stop before reaching inside.
7. When the cycle ends, remove items immediately and hang
Fill dryer drum 1/3 to 1/2 full.
or fold. If load is removed before the cycle ends, turn cycle selector to OFF.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cycle Signal Control (some models)
Features
WhentheCycleSignalControlisON, asignalwillsoundattheendofeachcycleand
during the Press Saver setting (some models). The volume is adjustable on some
models.
Drum Light (some models)
Adrumlightwillcomeonwheneverthedoorisopenedtoilluminatethedryerdrum
during loading and unloading. Closing the door turns off the light.
Drying Rack (some models)
Use the drying rack to dry items which should not be tumble dried.
1. Open the dryer door and remove the lint screen.
2. Insertdryingrackintothedryerdrum. Placethefrontbarunderthelipofthelint
screen opening.
3. Place items to be dried on top of rack. Weight should not exceed 10 lbs. Leave
space between items, but do not let items hang over the sides or through the
grids. Do not tumble other items when using the drying rack.
4. Selectatimeddrysettingbestsuitedforitemsbeingdried. UseonlytheAirFluff
(noheat)temperaturesettingforitemscontainingplastic,foamrubber,rubber-
like materials, feathers or down.
5. When items are dry, remove the rack and replace the lint screen. If lint screen
isnotinplace,tumblingitemscouldentertheexhaustsystemandcausedamage
to the dryer.
Use the drying rack to dry items which should
not be tumbled.
Common Drying Problems
Many drying problems involve poor cleaning results, poor soil and stain removal, residues of lint and scum, and fabric damage.
For satisfactory drying results, follow these suggestions provided by The Soap and Detergent Association.
PREVENTIVE MEASURES
PROBLEM POSSIBLE CAUSES
SOLUTIONS
Greasy, oily
stains
•Add a few bath towels to small loads for proper
tumbling.
•Rub fabric softener stains with bar soap.
Rinse and rewash.
•Fabric softener sheet.
•Some "silk-like" fabrics should be air dried.
•Use proper drying temperature.
•Place fabric softener sheet on top of load before
starting the dryer.
Lint
•Do not overload dryer.
•Use fabric softener in washer or dryer to reduce
static electricity.
•Remove items when they are slightly damp to
avoid overdrying.
•Check that lint screen is clean and in place.
•Reduce load size and rewash using
liquid fabric softener in the final rinse.
•Or, add a fabric softener sheet and
tumble without heat.
•Overloading.
•Overdrying causes static
electricity.
•Lint screen not clean
when cycle began.
•Lint is attached to "pills."
•Use lint brush or roller to remove lint.
Pilling
(Fibers break off,
ball up and cling
to fabric.)
•Use fabric softener to lubricate fibers.
•When ironing, use spray starch or fabric finish on
collars and cuffs.
•Use a lint brush or shaver to remove pills.
•Pilling is normal with
synthetic and permanent
press fabrics. This is due to
abrasion from normal
•Turn items inside out to reduce abrasion.
wear.
Shrinking
•Follow fabric care label directions.
•If shrinking is a concern, check load often.
•Remove items while slightly damp.
•Block knits into shape.
•Irreversible condition.
•Overdrying.
•Lay flat to complete drying.
Wrinkling
•Do not overload dryer.
•Remove items as soon as cycle ends.
•Reduce load size and tumble at medium
or low heat for 5-10 minutes.
•Remove items immediately. Hang or fold.
•Overloading.
•Leaving items in dryer
after cycle ends.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
To reduce risk of fire or serious injury to persons or property, comply
withthebasicwarningslistedinImportantSafetyInstructions,page2,andthose
listed below.
Care and Cleaning
•
Beforecleaningthewasherordryerinterior,unplugtheelectricalpowercord
to avoid electrical shock hazards.
•
Do not use any type spray cleanser when cleaning dryer interior. Hazardous
fumes or electrical shock could occur.
Inside the Washer
•
•
•
•
Removeitemsfromthewasherassoonasthecycleends.Excesswrinkling,color
transfer, and odors may develop in items left in the washer.
Dry the washer top, the area around the lid opening, and the underside of the
lid. These areas should always be dry before the lid is closed.
Beforecleaningthewasherinterior,unplugtheelectricalpowercordtoavoid
electrical shock hazards.
When extremely soiled items have been washed, a dirty residue may remain on
the tub. Remove this by wiping the tub with a nonabrasive household cleanser.
Rinsethoroughlywithwater.
Clean lint screen after every load.
•
The agitator or tub may become stained from fabric dye. Clean these parts with
a nonabrasive household cleanser. This prevents dye transfer to future loads.
Inside the Dryer
•
•
Clean the dryer lint screen after every load. Lint build-up in the screen restricts
air flow, which causes longer drying times. The screen is located at the bottom
ofthedooropening.Removebypullingstraightup.Removethelintandreplace
the screen.
Occasionallyawaxybuild-upmayformonthelintscreenfromusingdryer-added
fabric softener sheets. To remove this build-up, wash the lint screen in warm,
soapy water. Dry thoroughly and replace. Do not operate the dryer without the
lint screen in place.
Wash lint screen occasionally.
•
•
Ifthedryerdrumbecomesstainedfromnoncolorfastfabrics,cleanthedrumwith
a damp cloth and a mild liquid household cleanser. Remove cleanser residue
before drying the next load.
Use care with laundry
products. They can damage finish on
the laundry center.
Every 18 months an authorized servicer should clean the dryer cabinet interior
and exhaust duct. These areas can collect lint and dust over time. An excessive
amountoflintbuild-upcouldresultininefficientdryingandpossiblefirehazard.
Outside
•
When laundering is completed, wipe cabinet with a damp cloth. Turn water
faucets off to prevent pressure build-up in the hoses.
•
Clean the cabinet with mild soap and water. Never use harsh, gritty or
abrasivecleansers.Ifthecabinetbecomesstained,cleanwithdilutedchlorine
bleach [1/2 cup (120 ml) in 1 quart (.95 L) water]. Rinse several times with clear
water.
•
Remove glue residue from tape or labels with a mixture of warm water and mild
detergent. Or, touch residue with the sticky side of the tape or label.
•
Beforemovingthelaundrycenter,placeastripofcardboardorthinfiberboard
under the front leveling legs to prevent floor damage.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
WinterizingInstructions
Ifthelaundrycenterisstoredinanareawherefreezingcanoccurormovedinfreezing
temperatures,followthesewinterizinginstructionstopreventdamagetothelaundry
center:
FollowWinterizing
Instructions for cold
weather care.
1. Turn off water supply faucets.
2. Disconnect hoses from water supply and drain water from hoses.
3. Plug electrical cord into a properly grounded electrical outlet.
4. Add 1 gallon nontoxic recreational vehicle (RV) antifreeze to empty wash tub.
Close lid.
5. Set cycle selector knob at a spin setting. Pull out knob and let washer spin for 1
minute to drain out all water. Not all of the RV antifreeze will be expelled.
6. Push in knob, unplug electrical power cord, dry tub interior, and close lid.
7. Store washer in an upright position.
8. To remove antifreeze from washer after storage, run empty washer through a
complete cycle using detergent. Do not add wash load.
Avoid Service Checklist
Before calling for service, review this list. It may save both time and expense. The list includes common concerns that are not the
result of defective workmanship or materials in this laundry center.
OCCURRENCE
WASHER - NOISE
POSSIBLE CAUSE
SOLUTION
"Clunking" or gear sounds.
This is normal.
A certain amount of "clunking" or gear
sounds are normal in a heavy-duty
washer.
Rattling and clanking noise.
Stop washer and check tub. If noise continues after
washer is restarted, objects may be in pump. Call your
authorized servicer.
Foreign objects such as coins or safety
pins may be in tub or pump.
To prevent unnecessary noise and damage to tub, fasten
fasteners and turn items inside out.
Belt buckles and metal fasteners are
hitting wash tub.
Squealing sound or hot
rubber odor.
Do not overload washer. Stop washer and reduce load.
Washer is overloaded.
Thumping sound.
This is usually normal. If sound continues, washer is probably
out of balance. Stop washer and redistribute wash load.
Heavy wash loads may produce a
thumping sound.
Vibrating noise.
Movelaundrycentersoitrestsfirmlyonsolidfloor. Additional
floor bracing may be needed. Adjust leveling legs. See
INSTALLATION INSTRUCTIONS for details.
Laundry center is not resting on a solid,
firm floor.
See INSTALLATION INSTRUCTIONS for removing shipping
bolt and block.
Shipping bolt and block have not been
removed during installation.
Stop washer and rearrange wash load.
Wash load unevenly distributed in tub.
WASHER-OPERATING
Washer does not start.
Close washer lid
Washer lid is open
Make sure plug fits tightly in wall outlet.
Electrical power cord may not be plugged
in or connection may be loose.
Reset circuit breaker or replace fuse. Do not increase fuse
capacity. If problem is a circuit overload, have it corrected
by a qualified electrician. If problem is a power outage,
call local electric company.
Housefuseblown, circuitbreakertripped,
or a power outage has occurred.
Turn on water supply faucets.
Water supply faucets are not turned on.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OCCURRENCE
POSSIBLE CAUSE
SOLUTION
WASHER - OPERATING
(continued)
Move indicator clockwise slightly. Pull out knob.
Washer does not start
(continued).
Cycle selector is not in correct position.
Motor is overheated.
Washer motor will stop if it becomes overheated. It will
automatically restart after a cool down period of up to
30 minutes (if washer has not been manually turned
off).
Close lid completely. Safety lid lock must not be broken.
Washer won't spin.
Residue left in tub.
Lid is not completely closed.
Heavily soiled items.
Wipe tub with a nonabrasive household cleanser, then
rinse. Shake or brush excess dirt and sand from items
before washing.
WASHER-WATER
Do not overload washer. See Washing Procedures.
Rearrange load to allow proper spinning.
Straighten drain hose.
Wash load too wet after Washer is overloaded.
spin.
Load is out of balance.
Drain hose is kinked.
Check another faucet in the house. Wait until water
supply and pressure increase.
Water does not enter Water supply is not adequate in area.
washer or it enters slowly.
Fully open hot and cold faucets.
Water supply faucets are not completely open.
Water is being used elsewhere in the house.
Water pressure must be at least 30 psi (260 kPa). Avoid
running water elsewhere while washer is filling.
Straighten hoses.
Water inlet hoses are kinked.
Do not overload washer. When control is set at highest
fill level, dry load level should not be higher than top row
of circular holes in wash tub.
Water level does not cover Washer is overloaded.
load.
Measure hot water temperature at nearby faucet with
candy or meat thermometer. Water temperature should
be at least 120°F (49°C). Adjust water heater as
necessary.
Warm or hot water is not Hot water heater is set too low or is a
hot enough.
distance from laundry center.
Avoid using hot water elsewhere before or during
washer use. There may not be enough hot water
available for proper cleaning. If problem persists, your
hot water system may be unable to support more than
1 use at a time.
Hot water is being used elsewhere in
the house.
See Operating Instructions for your washer
To conserve energy, the temperature of
the cold and hot wash are regulated.
Clean and straighten the drain hose.
Water in washer does not Drain hose is kinked or clogged.
drain or drains slowly.
Check and tighten hose connections. Install rubber
sealing washers provided.
Water leaks.
Loose fill hose connection at faucet or
washer.
Unclog drain pipes. Contact plumber if necessary.
Use less detergent.
House drain pipes are clogged.
Oversudsing.
Connect hot water hose to hot water faucet and cold
water hose to cold water faucet.
Incorrect wash and rinse Hot and cold water hoses are connected
temperatures. to wrong supply faucets.
Standpipe must be a minimum of 33" (83.82 cm) high
to prevent siphoning. See INSTALLATION
INSTRUCTIONS.
Water is entering washer Drain hose standpipe is incorrect height.
but tub does not fill.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
OCCURRENCE
DRYER
POSSIBLE CAUSE
SOLUTION
Electrical power cord is not securely
plugged in or plug may be loose.
Make sure the plug fits tightly in wall outlet.
Dryer does not start.
House fuse blown or circuit breaker
tripped.
Reset circuit breaker or replace fuse.
Make sure electrical line is not overloaded and the dryer
is on a separate circuit.
Thermal limiter tripped.
Call authorized service person for replacement.
Replace fuse.
There are 2 house fuses in the dryer
circuit. If 1 of the 2 fuses is blown, the
drum may turn but the heater will not
operate.
Dryer runs but won't
heat.
Gas supply valve is not open (gas models).
Check to make sure supply valve is open. See
INSTALLATION INSTRUCTIONS for procedure.
Dryer does not have enough air supply to
support the burner flame (gas models).
See INSTALLATION INSTRUCTIONS.
LP gas supply tank is empty or there has
been a utility interruption of natural gas
(gas models).
Refill or replace tank.
Dryer should heat when utility service is restored.
Lint screen is clogged with lint.
Make sure all lint has been removed from the dryer lint
screen before starting each cycle.
Drying cycle takes too
long, outsideofthedryer
feels too hot or smells
hot.
Exhaust duct requirements have not been
met.
Exhaust duct must be at least 4 inches in diameter and
made of rigid or flexible metal.
When in place, the duct must have no more than two
90° bends and must not exceed length listed in
INSTALLATION INSTRUCTIONS.
Electric dryer is connected to a 208 volt
circuit.
Drying time will be 20% longer than drying on a 240 volt
circuit.
Drying procedures have not been
followed.
See Drying Procedures .
Outside exhaust hood or exhaust duct
may be clogged or restricted.
Clean out any obstruction.
High humidity.
Use a dehumidifier near the dryer.
Do not overload. See Drying Procedures .
Remove items as soon as cycle ends.
See Drying Procedures .
Excessive wrinkling.
Dryer is overloaded.
Items left in dryer too long.
Insufficient sorting of items.
Drying temperature too high.
Follow fabric care label instructions.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
CROSLEY® WARRANTY
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux will pay
allcostsforrepairingorreplacinganypartsofthisappliancethatprovetobedefectiveinmaterialsorworkmanshipwhensuch
appliance is installed, used and maintained inaccordance with the provided instructions.
Exclusions
This warranty does not cover the following:
1. Products with original serial numbers that have been removed, altered or cannot be readily determined.
2. Product that has been transferred from its original owner to another party or removed outside the USA or
Canada.
3. Rust on the interior or exterior of the unit.
4. Products purchased "as-is" are not covered by this warranty.
5. Food loss due to any refrigerator or freezer failures.
6. Products used in a commercial setting.
7. Service calls which do not involve malfunction or defects in materials or workmanship, or for appliances not
in ordinary household use or used other than in accordance with the provided instructions.
8. Service calls to correct the installation of your appliance or to instruct you how to use your appliance.
9. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,
etc.,which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace appliance light bulbs, air filters, water filters, other consumables, or knobs,
handles, or other cosmetic parts.
11. Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry trip
charges, or mileage expense for service calls to remote areas, including the state of Alaska.
12. Damages to the finish of appliance or home incurred during installation, including but not limited to
floors,cabinets, walls, etc.
13. Damages caused by: services performed by unauthorized service companies; use of parts other
than genuine Electrolux parts or parts obtained from persons other than authorized service companies;
or external causes such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMEROFIMPLIEDWARRANTIES;LIMITATIONOFREMEDIES
CUSTOMER’SSOLEANDEXCLUSIVEREMEDYUNDERTHISLIMITEDWARRANTYSHALLBE
PRODUCTREPAIRORREPLACEMENTASPROVIDEDHEREIN. CLAIMSBASEDONIMPLIED
WARRANTIES,INCLUDINGWARRANTIESOFMERCHANTABILITYORFITNESSFORAPARTICULAR
PURPOSE, ARELIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT
LESSTHANONEYEAR.ELECTROLUXSHALLNOTBELIABLEFORCONSEQUENTIALORINCIDENTAL
DAMAGESSUCHASPROPERTYDAMAGEANDINCIDENTALEXPENSESRESULTINGFROMANY
BREACHOFTHISWRITTENLIMITEDWARRANTYORANYIMPLIEDWARRANTY.SOMESTATESAND
PROVINCESDONOTALLOWTHEEXCLUSIONORLIMITATIONOFINCIDENTALORCONSEQUENTIAL
DAMAGES,ORLIMITATIONSONTHEDURATIONOFIMPLIEDWARRANTIES,SOTHESELIMITATIONS
OREXCLUSIONSMAYNOTAPPLYTOYOU.THISWRITTENWARRANTYGIVESYOUSPECIFICLEGAL
RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty
periodshould service be required. If service is performed, it is in your best interest to obtain and keep all
receipts.Service under this warranty must be obtained by contacting Electrolux at the addresses or
phonenumbersbelow.
This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major Appliances
NorthAmerica,adivisionof ElectroluxHomeProducts,Inc.InCanada,yourapplianceiswarrantedbyElectroluxCanadaCorp.
Electroluxauthorizesnopersontochangeoraddtoanyobligationsunderthiswarranty.Obligationsforserviceandpartsunder
thiswarrantymustbeperformedbyElectroluxoranauthorizedservicecompany.Productfeaturesorspecificationsasdescribed
or illustrated are subject to change without notice.
Replacement parts
If you need to order replacement parts, we recommend that you only use the factory specified parts. These parts will fit right
and work right because they are made with the same precision used to build every new Crosley ® appliance.
To locate factory specified replacement parts in you area call:
USA, 1-800-944-9044, or your nearest designated service center. In Canada call 1-800-668-4606.
For information on how to contact Crosley Corporation, please see page 2 of this document.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
|