Use & Care Manual
Side by Side
Refrigerator
Welcome
2
3
Safety Instructions
Installation -- Includes Connecting
IHousehold Water Supply to refrigerator
4 - 5
Door Removal
Instructions
6
Features at a Glance
7
Temperature Controls 8 - 11
Looking Inside
Automatic Ice and Water
12 - 13
Dispenser
14 - 20
Food Storage
& Energy Saving Tips
21
Normal Operating Sounds 22
Care & Cleaning
23 - 24
25
Warranty
30
59
Español
Français
Before You Call
Solutions to
Common Problems
26 - 29
PN: 241824400 (Jan 2007)
READ AND SAVE THESE INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
WARNING
Please Read All Instructions Before Using This
Refrigerator.
These Guidelines Must Be FollowedTo Ensure That
Safety Mechanisms In This Refrigerator Will Operate
Properly.
FORYOUR SAFETY
ELECTRICAL INFORMATION
•
Do not store or use gasoline, or other flammable liquids in
the vicinity of this or any other appliance. Read product
labels for warnings regarding flammability and other
hazards.
•
The refrigerator must be plugged into its own
dedicated 115 Volt, 60 Hz., 15 Amp, AC only electrical
outlet. The power cord of the appliance is equipped with a
three-prong grounding plug for your protection against
electrical shock hazards. It must be plugged directly into a
properly grounded three prong receptacle. The receptacle
must be installed in accordance with local codes and
ordinances. Consult a qualified electrician. Avoid
•
•
•
Do not operate the refrigerator in the presence of
explosive fumes.
Avoid contact with any moving parts of automatic ice
maker.
Remove all staples from the carton. Staples can cause
severe cuts, and also destroy finishes if they come in
contact with other appliances or furniture.
connecting refrigerator to a Ground Fault Interruptor (GFI)
circuit. Do not use an extension cord or adapter plug.
•
•
If the power cord is damaged, it should be replaced by an
authorized service technician to prevent any risk.
Never unplug the refrigerator by pulling on the power
cord. Always grip the plug firmly, and pull straight out
from the receptacle to prevent damaging the power cord.
CHILD SAFETY
Destroy or recycle the carton, plastic bags, and any exterior
wrapping material immediately after the refrigerator is
unpacked. Children should NEVER use these items to play.
Cartons covered with rugs, bedspreads, plastic sheets or
stretch wrap may become airtight chambers, and can quickly
cause suffocation.
•
•
Unplug the refrigerator before cleaning and before
replacing a light bulb to avoid electrical shock.
Performance may be affected if the voltage varies by
10% or more. Operating the refrigerator with insufficient
power can damage the compressor. Such damage is
not covered under your warranty.
PROPER DISPOSAL OFYOUR REFRIGERATOR OR
FREEZER
•
Do not plug the unit into an electrical outlet controlled by a
Risk of child entrapment
wall switch or pull cord to prevent the refrigerator from
being turned off accidentally.
Child entrapment and suffocation
are not problems of the past.
Junked or abandoned refrigerators
or freezers are still dangerous –
even if they will sit for “just a few
days.” If you are getting rid of your
old refrigerator or freezer, please
follow the instructions below to
help prevent accidents.
IMPORTANT
Pressing and holding the On/Off button for 3 seconds,
located on the left side of the temperature control panel
(Electronic controls), or turning the Freezer and Fresh Food
controls to “0” (Mechanical controls) will disable your
refrigerator’s cooling system, but does not disconnect the
power to the light bulb and other electrical components. To
turn off power to your refrigerator you must unplug the
power cord from the electrical outlet.
Before you throw away your old refrigerator/ freezer:
•
•
Remove doors.
Leave shelves in place so children may not easily climb
inside.
•
Have refrigerant removed by a qualified service
technician.
Grounding type
wall receptacle
Do not, under
any circumstances,
cut, remove,
or bypass the
grounding prong.
Power cord with
3-prong grounded plug
3
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
This Use & Care Manual provides general operating
instructions for your model. Use the refrigerator only as
Tabs
instructed in this Use & Care Manual. Before starting the
refrigerator, follow these important first steps.
LOCATION
•
Choose a place that is near a grounded electrical outlet.
Do Not use an extension cord or an adapter plug.
Tab
•
If possible, place the refrigerator out of direct sunlight
and away from the range, dishwasher or other heat
sources.
•
•
The refrigerator must be installed on a floor that is level
and strong enough to support a fully loaded refrigerator.
Consider water supply availability for models equipped
with an automatic ice maker.
Toe
Grille
To Remove Toe Grille:
1. Open freezer and fresh food compartment doors.
2. Working from left side of toe grille, slip your fingers
between top of toe grille and cabinet. Gently pull
forward until first set of
INSTALLATION
tabs are free. Slide
your hand down past
CAUTION
Cabinet
the free tabs and pull
forward again until the
second set of tabs are
Do Not install the refrigerator where the temperature
will drop below 55°F (13°C) or rise above 110°F (43°C).
The compressor will not be able to maintain proper
temperatures inside the refrigerator.
Toe
Grille
free. Continue this
process until all tabs
are free and the toe
grille can be removed.
(See graphic at top of
page in right column.)
Do Not block the toe grille on the lower front of your
refrigerator. Sufficient air circulation is essential for the
proper operation of your refrigerator.
Installation Clearances
LEVELING
•
Allow the following clearances for ease of installation,
proper air circulation, and plumbing and electrical
connections:
All four corners of your refrigerator must rest firmly on a solid floor.
Your refrigerator is equipped with adjustable front rollers to help level
your unit.To ensure proper door seal and assist door closing, the
refrigerator should be tilted 1/4” (6 mm), front to back.
To LevelYour Refrigerator:
1. Remove toe grille. (See “To Remove Toe Grille” .)
Sides & Top ------------------ 3/8”
Back---------------------------- 1”
DOOR OPENING
2. Use flat-blade screwdriver or 3/8” socket wrench to adjust
front rollers.
NOTE
If your refrigerator is placed with the door hinge side
against a wall, you may have to allow additional space so
the door can be opened wider.
NOTE
The refrigerator doors are designed to shut by themselves
within a 20 degree opening.
Your refrigerator should be positioned to allow easy access to a
counter when removing food. For best use of drawers and freezer
baskets, the refrigerator should be in a position where both the
refrigerator and freezer doors can be fully opened.
Raise
TOE GRILLE INSTALLATION / REMOVAL
To Install Toe Grille:
1. Open freezer and fresh food compartment doors.
2. Line up toe grille at base of refrigerator, making sure the
four bottom tabs are resting through holes at base of
cabinet.
3. Starting from left side of toe grille, press in on first top tab
using your thumb and push toe grille forward until it snaps
in place. Continue this process until all tabs are snapped
in place and toe grille is secured to refrigerator.
3. Check both doors to be sure seals touch cabinet on all four
sides.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
CONNECTING HOUSEHOLD WATER SUPPLY TO REFRIGERATOR
To Connect Water Supply Line To Ice Maker Inlet Valve
WARNING
1. Disconnect refrigerator from electric power source.
2. Place end of water supply line into sink or bucket. Turn ON
water supply and flush supply line until water is clear. Turn
OFF water supply at shutoff valve.
3. Unscrew plastic cap from water valve inlet and discard
cap.
To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator from
electrical power before connecting a water supply line
to the refrigerator.
4. Slide brass compression nut, then ferrule (sleeve) onto
water supply line, as shown.
CAUTION
5. Push water supply line into water valve inlet as far as it will
go (¼ inch). Slide ferrule (sleeve) into valve inlet and
finger tighten compression nut onto valve. Tighten another
half turn with a wrench; DO NOT over tighten.
6. With steel clamp and screw, secure water supply line to
rear panel of refrigerator as shown.
7. Coil excess water supply line (about 2½ turns) behind
refrigerator as shown and arrange coils so they do not
vibrate or wear against any other surface.
8. Turn ON water supply at shutoff valve and tighten any
connections that leak.
9. Reconnect refrigerator to electrical power source.
10. To turn ice maker on, lower wire signal arm (side mounted)
or set the ice maker’s On/Off power switch to the “I”
position (rear mounted).
To Avoid Property Damage:
•
Copper tubing is recommended for the water supply
line. Water supply tubing made of ¼” plastic is not
recommended since it greatly increases the potential
for water leaks. Manufacturer will not be responsible
for any damage if plastic tubing is used for supply
line.
DO NOT install water supply tubing in areas where
temperatures fall below freezing.
Chemicals from a malfunctioning softener can
damage the ice maker. If the ice maker is connected
to soft water, ensure that the softener is maintained
and working properly.
•
•
Plastic Water Tubing
Steel
Clamp
to Ice Maker
Fill Tube
IMPORTANT
Brass
Compression
Nut
Ensure that your water supply line connections comply with
all local plumbing codes.
Ferrule
(Sleeve)
Before Installing The Water Supply Line,You Will Need:
Copper
water line
•
•
•
Basic Tools: adjustable wrench, flat-blade screwdriver,
and PhillipsTM screwdriver
Water Valve
Bracket
Access to a household cold water line with water pressure
between 30 and 100 psi.
Valve Inlet
A water supply line made of ¼ inch (6.4 mm) OD, copper
tubing. To determine the length of copper tubing needed,
you will need to measure the distance from the ice maker
inlet valve at the back of the refrigerator to your cold water
pipe. Then add approximately 7 feet (2.1 meters), so the
refrigerator can be moved out for cleaning (as shown).
Water Valve
Copper water line
from household water supply
•
•
A shutoff valve to connect the water supply line to your
household water system. DO NOT use a self-piercing type
shutoff valve.
A compression nut and ferrule (sleeve) for connecting the
water supply line to the ice maker inlet valve.
(Include enough tubing in loop to allow
moving refrigerator out for cleaning.)
IMPORTANT
NOTE
After connecting the water supply, refer to “How to Prime
the Water Supply System” for important information about
priming an empty water supply system.
Water line kit number 5303917950, available from your
appliance dealer at additional cost, contains 25 feet (7.6
meters) of ¼ inch OD copper tubing, a saddle type shutoff
valve (nonpiercing), (2) ¼ inch brass compression nuts, (2)
ferrules/sleeves, and instructions for installing a water
supply line.
Your refrigerator’s water supply system includes
several tubing lines, a water filter, a water valve and a
water tank.To ensure that your water dispenser works
properly, this system must be completely filled with
water when your refrigerator is first connected to the
household water supply line.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DOOR REMOVAL INSTRUCTIONS
Tools Necessary:
Top
Hinge
Screw
Top Hinge
Cover Screw
3/8”
Adjustable
Wrench
Fixed
Wrench
Bottom
Hinge
Screw
OR
Phillips™ head
and
Flat Head
Socket
Screw Driver
Wrench Set
DOOR REMOVAL INSTRUCTIONS:
If it is necessary to move the refrigerator through narrow doorways, follow
these steps to remove the doors.
Before you start:
1 Make sure the electrical power cord is unplugged from the wall outlet.
2 Remove any food from the door shelves.
3 Close the doors.
To remove the hinge cover:
1 Remove the three screws from the cover over the top door hinges.
2 Pull the cover forward about a half inch and lift it off.
To remove the refrigerator door:
1 Trace lightly around the door’s top hinge with a pencil. This makes reinstallation
easier.
2 Remove the two screws from the top hinge. Lift the door off of the bottom hinge and
set it aside.
3 Remove the three bottom hinge screws and hinge, if necessary.
To remove the freezer door:
1 Detach the multi-wire cable connector located above the top hinge. Grasp both sides
of the connector firmly and pull apart.
2 Trace lightly around the door’s top hinge with a pencil. This makes reinstallation
easier.
3 Detach the water tube from the connector located below the freezer door. The
connector releases when you press its outer sleeve inward.
4 Remove the screws from the top hinge and pull the multi-wire cable through it.
5 Lift the door off of the bottom hinge. Lay the door on its side to avoid damage to the
Remove the three bottom hinge screws and hinge, if necessary.
To reinstall the refrigerator and freezer doors, reverse the above steps.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES AT A GLANCE
Features may vary according to model
Electronic Controls
Mechanical Controls
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MECHANICALTEMPERATURE CONTROLS
COOL DOWN PERIOD
To ensure safe food storage, allow the refrigerator to operate with the doors closed for at least 8 to 12 hours before loading it with
food.
REFRIGERATOR & FREEZER CONTROLS
NOTE
When changing control settings, wait 24 hours for the temperature to stabilize before making additional changes.
TEMPERATURE ADJUSTMENT
•
After 24 hours, adjust the controls as needed.Adjust temperatures gradually; move the knob in small increments, allowing the
temperature to stabilize.
•
•
For colder temperatures, turn the knob towards Colder.
For warmer temperatures, turn the knob towards Cold.
To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, do not block cold air
vents with food items.
* IMPORTANT
Turning the Freezer and Fresh Food Controls to “0” turns
off the compressor and prevents your refrigerator from
cooling, but does not disconnect the power to the light bulb
and other electrical components. To turn off power to your
refrigerator you must unplug the power cord from the
electricl outlet.
Refrigerator & Freezer Controls
(Features may vary according to model.)
TEMPERATURE ADJUSTMENT GUIDE
Turn Fresh Food Control Slightly Towards Colder.
Turn Fresh Food Control Slightly Towards Cold.
Turn Freezer Control Slightly Towards Colder.
Turn Freezer Control Slightly Towards Cold.
Turn Freezer and Fresh Food Controls To O.
If Fresh Food Compartment Is Too Warm
If Fresh Food Compartment Is Too Cold
If Freezer Compartment Is Too Warm
If Freezer Compartment Is Too Cold
* To Turn Refrigerator Off
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRONIC TEMPERATURE CONTROLS
ALLOWING COOLINGTIME BEFORE USE
To ensure safe food storage, allow your refrigerator to operate with the doors closed for at least 8 to 12 hours before placing food inside. During
this cooling period, you do not need to adjust the controls, which are preset at the factory.
SETTING COOLINGTEMPERATURES
Your refrigerator comes with a state-of-the-art electronic digital control system.The system’s control panel is located at the top of the the fresh
food compartment.
The two digital displays on the left half of the control panel indicate the current settings or temperatures of your freezer and fresh food
compartments. The models with a 2-digit temperature display are for reference only, and do not display the current accurate compartment
temperature. Should you desire to see what the current accurate temperature is, place a separate thermometer inside the freezer or fresh
food compartment in the desired location.
(Single Digit Display - Features may vary.)
NOTE
The advanced electronic control system in your refrigerator includes additional display modes that service professionals
can use to rapidly diagnose performance issues.
To adjust the temperature to a higher or lower setting, press the
Up (Cold) or Down (Colder) button closest to the display. The
first time you press the button, the display shows current
setting you entered. Each press of the button after that
changes the setting by one.
The display shows your new setting momentarily, then changes
back to the current temperature.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPERATURE CONTROLS
TEMPERATURE ADJUSTMENT
After 24 hours, adjust the controls as needed. Make your adjustments small and gradual; allowing time for temperatures to change
and stabilize. Refer to the adjacent guidelines for temperature settings.
To adjust the temperature to a higher or lower setting, press the Up or Down button closest to the display. The first time you press
the button, the display shows the last setting you entered. Each press of the button after that increments the setting by one
degree.
The display shows your new setting momentarily, then changes back to the current temperature.
IFTEMPERATURE DISPLAYS FLASH...
If ever you see both temperature displays continously flashing, it may indicate that the control system has detected a performance
problem. Call your service representative, who can interpret the flashing message.
To maintain temperatures, a fan circulates air in the refrigerator and freezer compartments. For good circulation, do not block cold
air vents with food items.
Numeric Display
Temperature Display (2-Digit)
Fresh
Food
Freezer
Fresh Food
Freezer
F°
C°
F°
C°
Warmest
Factory Setting
Coldest
1
6
9
1
6
9
Warmest
Factory Setting
Coldest
6°
0°
-14°
47°
8°
-18°
-21°
37°
33°
3°
1°
-6°
Temperature Adjustment Guide
Adjust Fresh Food control one degree
If Fresh Food compartment is too warm
colder by pressing Down (Colder) button.
Adjust Fresh Food control one degree
If Fresh Food compartment is too cold
If Freezer compartment is too warm
If Freezer compartment is too cold
warmer by pressing the Up (Cold) button.
Adjust Freezer control one degree colder
by pressing Down (Colder) button.
Adjust Freezer control one degree warmer
by pressing the Up (Cold) button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TEMPERATURE CONTROLS
Cooling System On/Off Button
TURNING THE COOLING SYSTEM ON AND OFF
Indicator Lights
You can disable the cooling system in your refrigerator by pressing the On/Off button located on the left side of the temperature
control panel. To ensure that you do not accidentally turn off the cooling system, the button does not work unless you press and
hold it for three seconds. Once you disable the cooling system, all refrigeration to the freezer and fresh food compartments stops.
To turn the cooling system back on, you must again press and hold the On/Off button for three more seconds.
NOTE
Pressing the On/Off button on the control panel disables your refrigerator’s cooling system but does not disconnect power to
lights and other electrical components. To turn off power to your refrigerator you must unplug the power cord from the wall
outlet.
Each time you make settings on the control panel, a single audible tone acknowledges your input.
RESPONDING TO ALARMS (Audible Tones & Indicator
AIR FILTER INDICATOR & STATUS LIGHTS
Lights)
Your refrigerator’s air filter needs to be replaced from time to
Your refrigerator’s control system can convey the following
information through audible tones and the alarm indicator
lights.
time.You can monitor the need for replacement by referring to
the status light while the air filter is “ON”. To turn on the air filter,
press the “Air Filter” button. To turn off the air filter, press the
“Air Filter” button. To RESET the air filter, press the “Air Filter”
button and hold for 3 seconds.
Door
Ajar
Flashing
Green
Freezer or
refrigerator door reset alarm.
has been open
for over five
minutes.
Close door to disable and
9
Air Filter Status Light (not available on all models)
Green
Yellow
Red
Filter OK.
Air filter is about 80 percent used. Please order new one.
Air filter is 100 percent used. Please change now.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOKING INSIDE
PIZZA SHELF (SOME
MODELS)
CANTILEVER SHELF ADJUSTMENT
Refrigerator shelves are easily adjusted to suit individual
needs. Before adjusting the shelves, remove all food. Cantilever
shelves are supported at the back of the refrigerator.
This shelf is attached to the
freezer wall beside the ice
dispenser container. This
convenient area allows for storage
of pizza and other tall items
placed vertically between the ice
dispenser container and the
freezer wall.
To adjust cantilever shelves:
1
2
Lift front edge up.
Pull shelf out.
Replace the shelf by inserting the hooks at rear of the shelf into
the wall bracket. Lower the shelf into the desired slots and lock
into position.
ICE CREAM SHELF (SOME
MODELS)
Pizza Shelf
* SpillSafeTM glass shelves (some models) catch and hold
accidental spills. In some models, the * SpillSafeTM shelves slide
out for easy access to food and for fast cleaning. The shelves
slide out independently of their mounting brackets. Just pull the
front of the shelf forward. Shelves can be extended as far as the
stopper will allow but are not removable from their mounting
brackets.
This shelf attaches to the top of
the ice dispenser container. It
allows storage of both round and
rectangular cartons of your
favorite ice cream.
TIP-UP SHELF (SOME
MODELS)
A Tip-Up shelf in the freezer
section allows tall items to be
easily stored.
1
2
Ice Cream Shelf
1
CAUTION
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break
suddenly if nicked, scratched, or exposed to sudden
temperature change. See “Glass Slelves” in Care &
Cleaning Chart.
2
Cantilever Glass Shelf
Cantilever Sliding Glass Shelf
DOOR STORAGE
Door bins and shelves are provided for convenient storage of
jars, bottles, and cans. Frequently used items can be quickly
selected.
ADJUSTABLE DOOR BINS
Some models have adjustable door bins that can be moved to
suit individual needs.
Some models have door bins that can accommodate gallon-
sized plastic drink containers and economy-sized jars and
containers. Some bins are adjustable for maximum storage
capacity.
To move door bins
1. Lift bin straight up.
2. Remove bin.
3. Place bin in desired position.
4. Lower bin onto supports until locked in place.
The dairy compartment, which is warmer than the general food
storage section, is intended for short term storage of cheese,
spreads, or butter.
Adjustable
Door Bin
Fixed Door Bin
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LOOKING INSIDE (CONTINUED)
SPECIAL ITEM RACK
(SOME MODELS)
TALL BOTTLE RETAINER (SOME MODELS)
The Tall Bottle Retainer keeps tall containers in the bin from
falling forward when opening or closing the refrigerator door. To The innovative design of
install, hold the retainer at the top, and slide it over the outside
wall of the bin, as shown in the diagram. The Tall Bottle
Retainer works best with a Bin Snugger.
the Special Item Rack
allows you to store a six-
pack of 12 ounce drink
cans, a bottle of wine, a
two-liter soft drink bottle,
or a carton of eggs. The
Special Item Rack mounts
on the left side of your
refrigerator. To install, just
slide the Special Item
Rack onto any shelf as
shown in the drawing.
Special ItemRack
Tall Bottle Retainer (left) and Bin Snugger (right)
DELI DRAWER (SOME MODELS)
Some models are equipped with a Deli Drawer for storage of
luncheon meats, spreads, cheeses, and other deli items.
CRISPERS
The crispers, located under
the bottom refrigerator shelf,
are designed for storing
fruits, vegetables, and other
fresh produce. Wash items in
clear water and remove
excess water before placing
them in the crispers. Items
with strong odors or high
moisture content should be
wrapped before storing.
MEAT KEEPER (SOME MODELS)
Some models are equipped with a Meat Keeper. Meat Keeper
temperatures can be adjusted by sliding the Meat Keeper
Temperature Control in either direction. Use this pan for short
term storage of bulk meat items. If meats are to be kept longer
than one or two days, they should be frozen. The Meat Keeper
is fixed and cannot be moved up or down. If fruits or vegetables
are to be stored in the Meat Keeper, set the Meat Keeper
Temperature Control to a warmer setting to prevent freezing.
Crisper Drawer
HUMIDITY CONTROL (SOME MODELS)
The Humidity Control, present on some models with crisper
drawers, allows you to adjust the humidity within the crisper.
This can extend the life of fresh vegetables that keep best in
high humidity.
Meat Keeper with
Temperature Control
NOTE
Leafy vegetables keep best when stored with the Humidity
Control set on Higher Humidity, or in a drawer without a
Humidity Control. This keeps incoming air to a minimum
and maintains maximum moisture content.
Wine Rack
WINE RACK (SOME
MODELS)
The wine rack stores bottles of
wine, or single two-liter plastic
bottles of juice or soda pop. To
install, slide the Wine Rack
onto the shelf with the curve
facing in. To remove, slide the
Wine Rack out. Install on either
side of shelf.
Crisper Humidity Control
13
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS
1
2
6
3
4
7
5
9
8
Features may vary according to model.
EXTREME
FREEZE
To freeze food at a faster rate to preserve freshness, push the Touch Pad 1 for 3-5 seconds to
activate this feature. A green light will appear above the Touch Pad. Push the Touch Pad
for 3-5 seconds to deactivate.
again
1
2
EXTRA
ICE
To increase ice production for special occasions, such as parties, push the Touch Pad
3-5 seconds to activate this feature. A green light will appear above the Touch Pad. Push the
Touch Pad again for 3-5 seconds to deactivate. Extra Ice should produce 25% to 50% more ice
for
2
every 24 hours.
3
CUBE
Press the CUBE Touch Pad
to get cubed ice. A green light will appear above the Touch Pad.
8
Press glass against ICE dispensing paddle
as far up as possible to catch all ice.
4
CRUSH
Press the CRUSH Touch Pad
Press glass against ICE dispensing paddle
to get crushed ice. A green light will appear above the Touch Pad.
8
as far up as possible to catch all ice.
5
5
LIGHT
Press the LIGHT Touch Pad
to turn on dispenser light. Press
again to turn the light off.
The light also turns on automatically when ice and/or water is dispensed. Replace light bulb with
an appliance bulb of the same wattage.
6
FILTER
STATUS
The FILTER STATUS indicator light above the Touch Pad
is used. The following filter light indications are:
will light up each time the dispenser
Green The filter is still operating within its specified life cycle.
Amber The filter has reached approximately 80% of its useful life. This is the recommended time
to purchase a replacement filter.
Red
The filter is 100% used up. Change the filter as soon as possible.
6
After the filter cartridge has been changed, press and hold the FILTER RESET Touch Pad
10-15 seconds.
for
NOTE: The Green, Red and Amber lights will flash when reset is completed.
The Ice & Water Dispenser can be locked out to prevent unwanted use.
LOCK
To Lock Out
Press the LOCK Touch Pad 7 for 3-5 seconds. A Red light will appear above
the Touch Pad.
7
To Unlock
Press the LOCK Touch Pad
Touch Pad goes out.
for 3-5 seconds until the Red light above the
9
WATER
To operate the water dispenser, press a glass against the WATER dispensing paddle
stop dispensing water, pull the glass away from the dispensing paddle
. To
9
. Dispensed water is not
cold. For colder water, add crushed ice or cubes before dispensing water. A drip tray located at
the base of the dispenser catches small spills and allows them to evaporate. This drip tray is
removable and dishwasher safe. Do not pour water and excess ice in this area because there
is no drain.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
AUTOMATIC ICE & WATER DISPENSER OPERATING INSTRUCTIONS
2
1
3
4
6
5
Features may vary according to model.
Press the Crush Touch Pad
ICE dispensing paddle
1
to get crushed ice. A red indicator will appear above the Touch Pad. Press glass against
as far up as possible to catch all ice.
Crush
Cube
5
Press the Cube Touch Pad
to get cubed ice. A red indicator will appear above the Touch Pad. Press glass against ICE
2
dispensing paddle
as far up as possible to catch all ice.
5
Press the Light On Touch Pad
Press the Light Off Touch Pad
to turn on dispenser light. A red indicator will appear above the Touch Pad.
to turn off dispenser light. A red indicator will appear above the Touch Pad.
Light On
Light Off
WATER
3
4
To operate the water dispenser, press a glass against the WATER dispensing paddle
the glass away from the dispensing paddle . Dispensed water is not cold. For colder water, add crushed ice or
cubes before dispensing water. A drip tray located at the base of the dispenser catches small spills and allows them to
evaporate. This drip tray is removable and dishwasher safe. Do not pour water and excess ice in this area because there
is no drain.
. To stop dispensing water, pull
6
6
15
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
cause the ice maker to cycle two or three times before making
a full tray of ice. With no usage, it will take approximately two
days to fill the ice container.
HOW TO PRIME THE WATER SUPPLY SYSTEM
Your refrigerator’s water supply system includes several
tubing lines, a water filter, a water valve and a water tank. To
ensure that your water dispenser works properly, this
system must be completely filled with water when your
refrigerator is first connected to the household water
supply line and whenever you replace the water filter.
Because of new plumbing connections, the first production of
ice cubes may be discolored or have an odd flavor. Discard
ice made during the first 24 hours.
TURNING YOUR SIDE MOUNTED ICE MAKER ON/OFF
To begin ice production, lower the wire signal arm to the
DOWN or ON position. The ice maker turns off automatically
when the ice container becomes full. To stop the ice maker,
raise the wire signal arm until it clicks and locks in the UP or
OFF position (see Figure 1).
CAUTION
For proper dispenser operation, recommended water
supply pressure should fall between 30 psi and 100 psi.
Excessive pressure may cause water filter to
malfunction.
TURNING YOUR REAR MOUNTED ICE MAKER ON/OFF
Ice production is controlled by the ice maker’s ON/OFF power
switch. To gain access to the ice maker, pull the ice cream
shelf out. Press the switch to the “O” position to turn it Off and
press it to the “I” position to turn it On (see Figure 2). The ice
maker also has a built-in wire signal arm, which automatically
stops ice production when the ice bin is full. DO NOT use this
signal arm to manually stop the ice maker.
TO PRIME THE WATER SUPPLY SYSTEM:
•
Begin filling the tank by pressing and holding a drinking
glass against the water dispenser paddle.
Keep the glass in this position until water comes out of
the dispenser. There will be noticeable spurts and
sputters as the system pushes air out through the
system and dispenser nozzle. This is normal. This may
take about 1½ minutes.
•
OR
•
Continue dispensing water for about 3 minutes to flush
the system of any air and impurities. Empty glass as
needed.
ON
OFF
OFF
ON
NOTE
Wire
Signal Arm
The water dispenser has a built-in device that shuts off the
water flow after 3 minutes of continuous use. To reset this
shutoff device, simply release the dispenser paddle.
HOW THE ICE MAKER WORKS
Figure 2
Figure 1
CAUTION
Chemicals from a malfunctioning softener can damage
the ice maker. If the ice maker is connected to soft
water, ensure that the softener is maintained and
working properly.
IMPORTANT
Small Ice cubes or ice chips jamming in the ice maker may
be a sign that your water filter needs changing. If you have
a side mounted ice maker you may also experience hollow
cubes — partially frozen cubes with water inside. When
these cubes are harvested they break open and spill water
over the other ice cubes in the ice container, forming a solid
mass of ice. As the water filter nears the end of its useful
life and becomes clogged with particles, less water is
delivered to the ice maker during each cycle. The ice maker
can’t fill every cube in the ice maker mold, leading to small
cubes or chips that can get caught between the ice ejector
blades and the stripper. Remember, if your ice maker is
jamming with small ice cubes or it’s been six months or
longer since you last changed your water filter –
replace the water filter with a new one. Poor quality
household water may require the filter to be changed
more frequently.
IMPORTANT
Your ice maker is shipped from the factory with the wire
signal arm in the ON position (side mounted) or with the
switch turned ON (rear mounted). To ensure proper function
of your ice maker, hook up water supply immediately or
turn ice maker OFF by lifting the wire signal arm until it
clicks and locks in the UP position (side mounted) or turn
the On/Off switch to the Off (O) position. If the ice maker is
not turned off and the water supply is not connected,
the water valve will make a loud chattering noise.
The ice maker and container are located in the top of the
freezer compartment. After the refrigerator is installed properly
and has cooled for several hours, the ice maker can begin
making ice within 24 hours. Air in new plumbing lines may
16
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
•
•
Remove ice chips and clean the shelf and chute that
supports the ice container.
ICE PRODUCTION: WHAT TO EXPECT
How Much Ice Will a Side Mounted Ice Maker
Produce in 24 Hours?
Replace the ice container. Resume ice production on
side-mounted ice makers by lowering the wire signal
arm to the DOWN position. Resume ice production on
rear-mounted ice makers by pressing the ice maker’s
On/Off power switch to the On (I) position.
A side mounted ice maker will produce 4 to 4.5 pounds of
ice every 24 hours, depending on usage conditions. Ice is
produced at a rate of 8 cubes every 75 to 90 minutes.
How Much Ice Will a Rear Mounted Ice Maker
Produce in 24 Hours?
A rear mounted ice maker will produce 3 to 4 pounds of ice
every 24 hours, depending on usage conditions. Ice is
produced at a rate of 8 cubes every 75 to 90 minutes.
WARNING
Do not use the ice chute as a handle when removing or
replacing the ice storage bin. Surfaces there may be
sharp. Do not put fingers up ice chute. Surfaces there
may be sharp.
ICE AND WATER DISPENSER FEATURES
The ice and water dispenser conveniently dispenses chilled
water, and ice cubes or crushed ice, depending on the model.
To operate the ice dispenser, select the ice option desired
using the touchpad. Press a glass against the dispensing
paddle as far up as possible to catch all ice. To stop
dispensing ice, pull glass away from dispensing paddle. Do
not remove the glass until the ice has completely dispensed.
Complete instructions for the dispenser operation are attached
to the inside of the freezer door (some models).
ICE DISPENSER TIPS
CAUTION
IMPORTANT
If the dispensing paddle is pushed for more than four
minutes, the dispenser motor may overload and stop.
The overload protector will reset automatically after
three or four minutes.
When removing or replacing the ice bin, DO NOT rotate the
auger in the ice bin. If the auger is accidentally rotated, you
must realign the auger by turning it in 90º turns until the ice
bin fits into place with the drive mechanism. If the auger is
not properly aligned when replacing the ice bin, the
refrigerator will only dispense Crushed Ice. The freezer
door may also not close properly causing warm air to leak
into the freezer.
•
Ice cubes stored too long may develop an odd flavor.
Empty the ice container and ensure that the ice maker is
on (see previous page). The ice maker will then produce
more ice.
•
•
•
•
Occasionally shake the ice container to keep ice
separated.
•
•
An extended power failure (one hour or longer) causes
ice cubes in the ice storage bin to melt and freeze
together and jam the dispenser mechanism.
The ice dispenser is not used frequently. Ice cubes will
freeze together in the bin and jam the dispenser
mechanism. Remove the ice storage bin and shake to
loosen the cubes.
If a large quantity of ice is needed at one time, it is best
to remove cubes directly from the ice container.
Stop the ice maker when cleaning the freezer and during
vacations.
If the ice maker will be turned off for a long period of
time, turn the water supply valve to a closed position.
CAUTION
CLEANING THE ICE DISPENSER
Clean the ice dispenser and ice container at regular intervals,
particularly before you take a vacation or move, or if the ice
dispenser sticks.
NEVER use an ice pick or similar sharp instrument to
break up the ice.This could damage the ice storage bin
and dispenser mechanism.
•
•
Stop ice production on side-mounted ice maker by
raising wire signal arm to the UP position. Stop ice
production on rear-mounted ice makers by pressing the
ice maker’s On/Off power switch to the Off (O) position.
Remove ice container by lifting up and out. Empty and
carefully clean the container with mild detergent. Rinse
with clear water. Do not use harsh or abrasive cleaners.
Allow ice container to dry completely before replacing in
the freezer.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
PURESOURCE TM * ICE AND WATER FILTER (SOME
MODELS)
moving for example), change the filter before reinstalling the
refrigerator. The dispenser system will also operate without
filtration (with filter cartridge removed).
NOTE
To change filter:
It is not necessary to turn the water supply off to change the filter.
If you purchased a refrigerator with a PureSource TM
*
Ice and Water filter, please read the following use and
care information. This ice and water filter system filters
water to your ice maker and water dispenser. It is located
in the upper right back corner of the refrigerator
compartment.
1. Open freezer door and leave open until filter change is
complete.
2. Turn OFF side mounted ice maker by raising wire signal
arm to the UP position. Turn OFF rear mounted ice maker
by pressing ON/OFF power switch to the “O” position.
3. Hold filter cup firmly, and unscrew towards left (Some water
could leak out as you remove cup.This is normal.). Filter
cartridge should come down with cup. If cartridge remains in
housing, pull down gently, while twisting filter back and forth.
4. Rinse out cup under running water.
5. The large o-ring that seals the filter system fits in the o-ring
groove inside the cup. Should the o-ring fall out during filter
cartridge replacement, simply place it back in the groove
prior to screwing the cup back in place. If the o-ring becomes
damaged, you will need to order one from the Electrolux
Solutions Hotline.
System Startup:
Water supply does not need to be turned off, however, do not use
ice and water dispenser while installing filter. The filter cartridge
has already been installed in the filter housing at the factory.
Refer to the How to Prime the Water Supply System section to
properly fill the system with water.
Order new filter
cartridges through the
dealer where you bought
the refrigerator, contact
the Electrolux Solutions
Hotline at 1-800-944-
9044, or go to our web
site at
might be good to order
some filter cartridges
when you first install your
refrigerator. Be sure to
ask for the RG-100
PureSource™*
6. Discard old filter cartridge.
7. Remove new filter cartridge from packaging. Place in cup. The
end with the small o-ring should be up, out of the cup.
8. Screw cup, with filter, back onto housing. Do Not Use Wrench
To Reinstall Cup. Filter cartridge will self-align as cup is
tightened. Be sure cup is completely tightened with
PureSource™ logo facing outward. Do NotTighten Past Stop.
9. Turn ON side mounted ice maker by lowering wire signal
arm to the DOWN position.Turn ON rear mounted ice
maker by pressing ON/OFF power switch to the “I” position.
10. Check for leaks. Open refrigerator door. Wipe any water droplets
from the filter cup. Fill a glass with water. If there is a leak,
unscrew filter cup, and reinsert the filter cartridge. Check
placement of large O-ring. Reinstall filter cup, making certain it is
tightened completely.
11. To prime filter system and purge air from water line,
continue flushing the system for approximately 3 minutes
to assure that the purest water possible is stored in the
water tank. There will be noticeable spurts and sputters
as the system pushes air out through the system and
out the dispenser nozzle.This is normal.
replacement cartridge.
The PureSource™ * NGRG-2000 Ice and Water
Filter System with the RG-100 cartridge is tested
and certified by NSF International, the nationally
recognized and respected, not for profit,
certification organization for public health safety.
The PureSource™* system is tested and certified to ANSI/
NSF Standard 42. See performance data sheet for
specifications. This system should not be used on water that is
microbiologically unsafe or with water of unknown quality
unless the water has been adequately disinfected before or
after traveling through the filtration system.
IMPORTANT
ResettingThe Filter Status Light (some models)
• Rated Capacity - 400 gallons
After replacing the filter cartridge, it will be necessary to press the
Filter Status reset button located on the ice and water dispenser.
This will reset the Filter Status light. Push the reset button until
the green, red and amber lights flash (10-15 seconds). Please
refer to the complete dispenser operating instructions attached to
the inside of the freezer door.
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
Changing the Filter:
Water conditions vary throughout the world, but changing the
water filter every 6 - 9 months normally will ensure the highest
possible water quality. Ice jams in the ice maker and/or hollow
ice cubes (partially frozen cubes with water inside), may
also be a sign that your water filter needs changing. The
Filter Status light will turn red after 400 gallons of water has
flowed through the ice and water dispenser. Also, if the filter has
been in a refrigerator that has not been in use for awhile (during
On models without a Filter Status reset button, there is a set
of Reminder Stickers included in the envelope that the Use &
Care Manual came in. Choose a dated sticker that indicates 6 - 9
months (depending on your water quality and usage) from the
date of installation. Place the sticker on the front of the filter cup
to remind you when it is time to change the filter.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
PURESOURCE2TM * ICE AND WATER FRONT FILTER
(SOME MODELS)
Also, if the filter has been in a refrigerator that has not been in
use for awhile (during moving for example), change the filter
before reinstalling the refrigerator. The dispenser system will also
operate without filtration (with filter cartridge removed and bypass
installed).
NOTE
If you purchased a refrigerator with a PureSource2TM *
Ice and Water front filter, please read the following use
and care information. This ice and water filter system
filters water to your ice maker and water dispenser. It is
located in the upper right front corner of the refrigerator
compartment.
To change filter:
It is not necessary to turn the water supply off to change the
filter.
1. Turn OFF side mounted ice maker by raising wire signal
arm to the UP position. Turn OFF rear mounted ice maker
by pressing ON/OFF power switch to the “O” position.
2. Push the Filter Release Button, located to the right of the
filter cartridge, to release the filter from the housing. To
minimize the possibility of the filter falling out of the
housing during removal, it would be best to hold the
filter as it moves out toward you.
System Startup:
Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter
housing at the factory. Refer to the How to Prime the Water
Supply System section to properly fill the system with water.
NOTE
Order new filter
A small amount of water may be released during this
operation.You should have a paper towel or dish cloth
handy to wipe up any water that may drip out of the filter or
housing. Two small holes near the back of the housing have
been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf
in advance of removing the filter.
cartridges through the
dealer where you
bought the refrigerator,
contact the Electrolux
Solutions Hotline at 1-
800-944-9044, or go to
our web site at
might be good to order
some filter cartridges
when you first install
your refrigerator. Be
sure to ask for the FC-
100 PureSource™*
replacement cartridge.
3. Pull the old filter cartridge straight out of the housing.
4. Discard the old filter.
5. Remove the new filter cartridge from the packaging and
insert into the filter housing the same way the old one
came out.
6. When the cartridge is almost in, you will feel it stop against
the clip assembly in the back of the housing. The clip
assembly holds the filter cartridge firmly in place. At this
point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of
the filter cartridge will be flush with the front of the housing.
7. Turn ON side mounted ice maker by lowering wire signal
arm to the DOWN position. Turn ON rear mounted ice
maker by pressing ON/OFF power switch to the “I”
position.
The PureSource2TM* Ice and Water Filter
System NGFC 2000 with the PureSource2TM*
cartridge FC 100 is tested and certified by
NSF International, the nationally recognized
and respected, not for profit, certification
organization for public health safety. The PureSource2TM*
Filter system is tested and certified to ANSI/NSF Standards
42 and 53. See performance data sheet for specifications.
This system should not be used on water that is
microbiologically unsafe or with water of unknown quality
unless the water has been adequately disinfected before or
after traveling through the filtration system.
8. Fill a glass with water. As you are doing this, check for
leaks at the filter housing.
9. To prime filter system and purge air from water line,
continue flushing the system for approximately 3 minutes
to assure that the purest water possible is stored in the
water tank. There will be noticeable spurts and sputters
as the system pushes air out through the system and
out the dispenser nozzle.This is normal.
• Rated Capacity - 400 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
IMPORTANT
Resetting The Filter Status Light (some models)
Changing the Filter:
Water conditions vary throughout the world, but changing the
water filter every 6 - 9 months normally will ensure the highest
possible water quality. Ice jams in the ice maker and/or
hollow ice cubes (partially frozen cubes with water inside),
may also be a sign that your water filter needs changing.
The Filter Status light will turn red after approximately 400
gallons of water has flowed through the ice and water dispenser.
After replacing the filter cartridge, it will be necessary to press the
Filter Reset button located on the ice and water dispenser. This
will reset the Filter Status light. Push the reset button until the
green, red and amber lights flash (10-15 seconds). Please refer
to the complete dispenser operating instructions attached to the
inside of the freezer door.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTOMATIC ICE AND WATER DISPENSER
PURESOURCE MB ICE AND WATER FRONT FILTER
(SOME MODELS)
be a sign that your water filter needs changing. The Filter
Status light will turn red after approximately 250 gallons of water
has
flowed through the ice and water dispenser. Also, if the filter has been
NOTE
in a refrigerator that has not been in use for awhile (during moving for
example), change the filter before reinstalling the refrigerator. The
dispenser system will also operate without filtration (with filter
cartridge removed and bypass installed).
If you purchased a refrigerator with a PureSource MB
Ice and Water front filter, please read the following use
and care information. This ice and water filter system
filters water to your ice maker and water dispenser. It is
located in the upper right front corner of the refrigerator
compartment.
To change filter:
It is not necessary to turn the water supply off to change the filter.
1. Turn OFF side mounted ice maker by raising wire signal
arm to the UP position.Turn OFF rear mounted ice maker
by pressing ON/OFF power switch to the “O” position.
2. Push the Filter Release Button, located to the right of the
filter cartridge, to release the filter from the housing. To
minimize the possibility of the filter falling out of the housing
during removal, it would be best to hold the filter as it moves out
toward you.
System Startup:
Water supply does not need to be turned off, however, do not
use ice and water dispenser while installing filter.
The filter cartridge has already been installed in the filter
housing at the factory. Refer to the How To Prime The Water
Supply System section to properly fill the system with water.
3. Pull the old filter cartridge straight out of the housing.
Order new filter
cartridges through the
dealer where you
NOTE
bought the refrigerator,
contact the Electrolux
Solutions Hotline at 1-
800-944-9044, or go to
our web site at
might be good to order
some filter cartridges
when you first install
your refrigerator. Be
sure to ask for the
A small amount of water may be released during this
operation.You should have a paper towel or dish cloth
handy to wipe up any water that may drip out of the filter or
housing. Two small holes near the back of the housing have
been added for any excess water to escape. It would be
best to clear away any food near this area on the top shelf
in advance of removing the filter.
4. Discard the old filter.
5. Remove the new filter cartridge from the packaging and
insert into the filter housing the same way the old one
came out.
MB100 replacement
cartridge WF2MB.
6. When the cartridge is almost in, you will feel it stop against
the clip assembly in the back of the housing. The clip
assembly holds the filter cartridge firmly in place. At this
point, you will need to push firmly until the cartridge
snaps fully in place. When completely in place, the front of
the filter cartridge will be flush with the front of the housing.
7. Replace the ice container. Turn ON side mounted ice
maker by lowering wire signal arm to the DOWN position.
Turn ON rear mounted ice maker by pressing ON/OFF
power switch to the “I” position.
The PureSource MB Ice and Water Filter System
MBFC 2003 with the PureSource MB cartridge
MB100 is tested and certified by NSF
International, the nationally recognized and
respected, not for profit, certification organization
for public health safety. The PureSource MB Filter system is
tested and certified to ANSI/NSF Standards 42 and 53. See
performance data sheet for specifications. PureSource MB,
MBFC-2003 Ice & Water Filter System should not be used on
water that is visually contaminated (cloudy) or has an obvious
contamination source, such as contamination by raw sewage.
State ofWisconsin requires statement:Do not use in Wisconsin
with water that is microbiologically unsafe, or of an unknown
quality without adequate point-of-entry disinfection before this
device.
8. Fill a glass with water. As you are doing this, check for
leaks at the filter housing.
9. To prime filter system and purge air from water line,
continue flushing the system for approximately 3 minutes
to assure that the purest water possible is stored in the
water tank. There will be noticeable spurts and sputters
as the system pushes air out through the system and
out the dispenser nozzle.This is normal.
• Rated Capacity - 250 gallons
• Rated service flow - .5 GPM
• Maximum Rated Pressure - 100 PSI
• Maximum Operating Temp. - 100° F
IMPORTANT
ResettingThe Filter Status Light (some models)
Changing the Filter:
After replacing the filter cartridge, it will be necessary to press the
Filter Reset button located on the ice and water dispenser. This
will reset the Filter Status light. Push the reset button until the
green, red and amber lights flash (10-15 seconds). Please refer
to the complete dispenser operating instructions attached to the
inside of the freezer door.
Water conditions vary throughout the world, but changing the
water filter every
6 - 9 months normally will ensure the highest possible water
quality. Ice jams in the ice maker and/or hollow ice cubes
(partially frozen cubes with liquid water inside), may also
20
Download from Www.Somanuals.com. All Manuals Search And Download.
FOOD STORAGE & ENERGY SAVING IDEAS
ENERGY SAVING IDEAS
FOOD STORAGE IDEAS
Fresh Food Storage
•
Locate the refrigerator in the coolest
part of the room, out of direct sunlight,
and away from heating ducts or
•
The fresh food compartment should be kept between 34°
F and 40° F with an optimum temperature of 37° F.
registers. Do not place the refrigerator
next to heat-producing appliances such
as a range, oven, or dishwasher. If this
•
Avoid overcrowding the refrigerator shelves. This reduces
the circulation of air around the food and results in uneven
cooling.
is not possible, a section of cabinetry or an added layer of
insulation between the two appliances will help the
refrigerator operate more efficiently.
Level the refrigerator so that the doors close tightly.
Refer to this Use & Care Manual for the suggested
temperature control settings.
Do not overcrowd the refrigerator or block cold air vents.
Doing so causes the refrigerator to run longer and use
more energy.
Cover foods and wipe containers dry before placing them
in the refrigerator. This cuts down on moisture build-up
inside the unit.
Organize the refrigerator to reduce door openings.
Remove as many items as needed at one time and close
the door as soon as possible.
Fruits and Vegetables
•
Storage in the crisper drawers traps moisture to help
preserve the fruit and vegetable quality for longer time
periods.
•
•
Meat
•
•
•
•
Raw meat and poultry should be wrapped securely so
leakage and contamination of other foods or surfaces
does not occur.
Frozen Food Storage
•
The freezer compartment should be kept at 0° F or lower.
•
A freezer operates most efficiently when it is at least 2/3
full.
Packaging Foods for Freezing
•
To minimize dehydration and quality deterioration, use
aluminum foil, freezer wrap, freezer bags or airtight
containers. Force as much air out of the packages as
possible and seal them tightly. Trapped air can cause food
to dry out, change color, and develop an off-flavor (freezer
burn).
•
•
Wrap fresh meats and poultry with suitable freezer wrap
prior to freezing.
Do not refreeze meat that has completely thawed.
Loading the Freezer
•
•
•
Avoid adding too much warm food to the freezer at one
time. This overloads the freezer, slows the rate of freezing,
and can raise the temperature of frozen foods.
Leave a space between the packages, so cold air can
circulate freely, allowing food to freeze as quickly as
possible.
Avoid storing hard-to-freeze foods such as ice cream and
orange juice on the freezer door shelves. These foods are
best stored in the freezer interior where the temperature
varies less.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
NORMAL OPERATING SOUNDS & SIGHTS
A. Evaporator
UNDERSTANDING THE SOUNDSYOU MAY HEAR
The flow of refrigerant through the evaporator may
create a boiling or gurgling sound.
Your new high-efficiency refrigerator may make unfamiliar
sounds. These are all normal sounds and soon will become
familiar to you. They also indicate your refrigerator is operating
as designed. Hard surfaces, such as vinyl or wood floors, walls,
and kitchen cabinets may make sounds more noticeable. Listed
below are descriptions of some of the most common sounds
you may hear, and what is causing them.
B. Evaporator Fan
You may hear air being forced through the refrigerator
by the evaporator fan.
C. Defrost Heater
During defrost cycles, water dripping onto the defrost
heater may cause a hissing or sizzling sound. After
defrosting, a popping sound may occur.
NOTE
Rigid foam insulation is very energy efficient, but is not a
sound insulator.
IMPORTANT
During the automatic defrost cycle, you may notice a red
glow in the vents on the back wall of your freezer
compartment. This is normal during the defrost cycle.
D. Automatic Ice Maker
If your refrigerator is equipped with an automatic ice
maker, you will hear ice cubes falling into the ice bin.
OR
K
E. Cold Control & Automatic Defrost Control
These parts can produce a snapping or clicking sound
when turning the refrigerator on and off.
D
F. Condenser Fan
E
D
OR
You may hear air being forced through the condenser
by the condenser fan.
B
A
G. Compressor
C
F
Modern, high-efficiency compressors operate much
faster than older models. The compressor may have a
high-pitched hum or pulsating sound.
G
H. Water Valve
J
H
I
If your refrigerator is equipped with an automatic ice
maker, you will hear a buzzing sound as the water
valve opens to fill the ice maker during each cycle.
IMPORTANT
Your ice maker is turned On at the factory so it can work as
soon as you install your refrigerator. To ensure proper
function of your ice maker, connect a water supply
immediately or turn the Ice maker off by lifting the wire
signal arm to the "up" or OFF position (side mounted) or
the ice maker’s On/Off power switch turned Off-set to the
“O” position (rear mounted) .
I. Drain Pan (not removable)
You may hear water running into the drain pan during
the defrost cycle.
J. Condenser
May create minimal sounds from forced air.
K. Motorized Damper
May produce a light humming during operation.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & CLEANING
Keep your refrigerator and freezer clean to prevent odor build-up. Wipe up any spills immediately and clean both sections at least
twice a year. Never use metallic scouring pads, brushes, abrasive cleaners or strong alkaline solutions on any surface. Do not
wash any removable parts in a dishwasher. Always unplug the power cord from the electrical outlet before cleaning.
CAUTION
•
When moving the refrigerator, pull straight out. Do not shift the refrigerator from side to side as this may damage
the floor. Be careful not to move the refrigerator beyond the plumbing connections.
•
•
Damp objects stick to cold metal surfaces. Do not touch refrigerated surfaces with wet or damp hands.
Never use CHLORIDE to clean stainless steel.
NOTE
•
The On/Off button on the Electronic Control only controls your refrigerator’s cooling system. To turn off power to your
refrigerator you must unplug the power cord from the electrical outlet.
•
Do not use razor blades or other sharp instruments which can scratch the appliance surface when removing adhesive
labels. Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent, or, touch the glue
residue with the sticky side of tape you have already removed. Do not remove the serial plate.
Care & Cleaning Chart
Part
What To Use
Tips and Precautions
Interior/Door
Liner
Use 2 tablespoons of baking soda in 1 quart of warm water. Be sure to wring
excess water out of sponge or cloth before cleaning around controls,
light bulb or any electrical part.
•
•
Soap and water
Baking soda and water
Wipe gaskets with a clean soft cloth.
Door Gaskets
Drawers/Bins
Glass Shelves
•
•
Soap and water
Soap and water
Do not wash any removable items (bins, drawers, etc.) in dishwasher.
Allow glass to warm to room temperature before immersing in warm water.
•
•
•
•
•
•
•
•
Soap and water
Glass cleaner
Mild liquid sprays
Soap and water
Mild liquid sprays
Vacuum attachment
Soap and water
Non Abrasive Glass
Cleaner
Toe Grille
Vacuum dust from front of toe grille. Remove toe grille. Vacuum backside and
wipe with sudsy cloth or sponge. Rinse and dry.
Do not use commercial household cleaners, ammonia, or alcohol to clean
handles. Use a soft cloth to clean smooth handles. Do Not use a dry cloth to
clean smooth doors.
Exterior and
Handles
•
•
•
Soap and water
Ammonia
Stainless Steel Cleaners
Exterior and
Handles
CAUTION: Never use CHLORIDE to clean stainless steel.
Clean stainless steel front and handles with soapy water and a dishcloth.
Rinse with clean water and a soft cloth. Wipe stubborn spots with an
ammonia-soaked paper towel, and rinse. Use a non-abrasive stainless steel
cleaner. These cleaners can be purchased at most home improvement or
major department stores. Always follow manufacturer's instructions.
(Stainless Steel
Models Only)
NOTE: Always clean, wipe and dry with the grain to prevent cross-grain
scratching. Wash the rest of the cabinet with warm water and mild liquid
detergent. Rinse well, and wipe dry with a clean soft cloth.
•
•
Soap and water
Mild liquid sprays
Exterior
CAUTION: DO NOT use abrasive or stainless steel cleaners on Easy
Care Stainless Steel Models. It will remove the protective finish.
(Easy Care
Stainless Steel
Models)
Use warm soapy water to clean Easy Care surfaces. Mild liquid sprays may
be used on stubborn spots.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
CARE & CLEANING (CONTINUED)
CAUTION
Wear gloves when replacing light bulbs to avoid getting
cut.
OR
Light
Shield
REPLACING LIGHT BULBS
1. Unplug refrigerator.
Screw
2. Wear gloves as protection against possible broken glass.
3. Remove light cover, if necessary.
4. Unscrew and replace old bulb with an appliance bulb of
the same wattage.
Refrigerator Lights
Located behind
control panel
Refrigerator Light Replacement
5. Replace light cover, if necessary.
6. Remember to plug the refrigerator back in.
or
Crisper Light Replacement (Models may vary)
Freezer Light Replacement
Vacation and Moving Tips
•
•
•
Leave refrigerator operating during vacations of 3 weeks or less.
Use all perishable items from refrigerator compartment.
Turn automatic ice maker off and empty ice bucket, even if you will only be gone for a
few days.
Short
Vacations
•
•
•
Remove all food and ice if you will be gone one month or more.
Turn off automatic ice maker and turn water supply valve to closed position.
Turning refrigerator controls to “OFF” by pressing and holding the On/Off button for 3
seconds (electronic) or turn control knobs to “0” (manual)on the mechanical controls only
controls your refrigerator’s cooling system. To turn off power to your refrigerator you
must unplug the power cord from the wall outlet.
Long
Vacations
•
•
Clean interior thoroughly.
Leave both doors open to prevent odors and mold build-up. Block doors open if
necessary.
•
•
•
•
Remove all food and ice.
If using handcart, load from side.
Adjust rollers all the way up to protect them during sliding or moving.
Pad cabinet to avoid scratching surface.
Moving
IMPORTANT
If the refrigerator is going to be stored or moved in freezing temperatures, the water in the ice and water
system must be drained completely. Failure to do so could result in water leaks when the refrigerator is put
back into service. Contact a service representative to perform this operation.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY
REFRIGERATOR WARRANTY
Your refrigerator is protected by this warranty
WARRANTY
PERIOD
THROUGH OUR AUTHORIZED SERVICERS,
WE WILL:
THE CONSUMER WILL BE RESPONSIBLE FOR:
One year from original
purchase date
Pay all costs for repairing or replacing any parts of this
appliance which prove to be defective in materials or
workmanship. Excludes original and replacement Ice
& Water filter cartridges (if equipped). Original and
replacement cartridges are warranted for 30 days
(parts only).
FULL ONE-YEAR
WARRANTY
Costs of service calls that are listed under NORMAL
RESPONSIBILITIES OF THE CONSUMER. *
* In addition to warranty shown above, ask your dealer about Crosley Extended Limited Warranty that comes to you at no extra charge for the 2nd through 10 th
years.
In the U.S.A., your appliance is warranted by Crosley Corporation. We authorize no person to change or add to any of our obligations under this
warranty. Our obligations for service and parts under this warranty must be performed by an authorized Crosley Corporation servicer. In Canada,
your appliance is warranted by Crosley Canada Corp.
This warranty applies only to products in ordinary household use, and the consumer is responsible for the
items listed below:
*NORMAL
RESPONSIBILITIES
OF THE CONSUMER
1. Proper use of the appliance in accordance with instructions provided with the product.
2. Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in
accordance with all local plumbing, electrical and/or gas codes.
3. Proper connection to a grounded power supply of sufficient voltage, replacement of blown fuses, repair of loose
connections or defects in house wiring.
4. Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards, shelves,etc.,
which are not a part of the appliance when it was shipped from the factory.
5. Damages to finish after installation.
6. Replacement of light bulbs and/or fluorescent tubes (on models with these features).
This warranty does not cover the following:
EXCLUSIONS
1. CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL
EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY.
NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so this
limitation or exclusion may not apply to you.
2. Service calls which do not involve malfunction or defects in workmanship or material, or for appliances not in
ordinary household use. The consumer shall pay for such service calls.
3. Damages caused by services performed by servicers other than Crosley Corporation, Crosley Canada Corp. or
its authorized servicers; use of parts other than genuine Crosley Corporation parts; obtained from persons other
than such servicers; or external causes such as abuse, misuse, inadequate power supply or acts of God.
4. Products with original serial numbers that have been removed or altered and cannot be readily determined.
Keep your bill of sale, delivery slip, or some other appropriate payment record. The date on the bill establishes the
warranty period should service be required. If service is performed, it is in your best interest to obtain and keep all
receipts. This written warranty gives you specific legal rights.You may also have other rights that vary from state to
state. Service under this warranty must be obtained by contacting Crosley Corporation or Crosley Canada Corp.
IF YOU NEED
SERVICE
This warranty only applies in the 50 States of the U.S.A., in Puerto Rico, and in Canada. Product features or specifications as described or
illustrated are subject to change without notice. All warranties are made by Crosley Corporation. In Canada, your appliance is warranted by
Crosley Canada Corp.
Rev. 01/2006
FOR PRODUCT INFORMATION CONTACT:
FOR WARRANTY INFORMATION CONTACT:
336-761-1212
Crosley Corporation
PO Box 2111
USA
800-944-9044
Canada 800-668-4606
Winston-Salem, NC 27102
25
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFOREYOU CALL
1-800-944-9044 (United States)
1-800-668-4606 (Canada)
Visit our web site at
PROBLEM
CAUSE
CORRECTION
RUNNING OF REFRIGERATOR
Compressor does not run.
•
•
Freezer control is set to "OF"
or “0”.
Refrigerator is in defrost cycle.
•
•
Set freezer control. See Temperature Controls section.
This is normal for a fully automatic defrost refrigerator.
The defrost cycle occurs periodically, lasting about 30
minutes.
•
•
Plug at electrical outlet is
disconnected.
House fuse blown or tripped
circuit breaker.
•
•
Ensure plug is tightly pushed into outlet.
Check/replace fuse with a 15 amp time-delay fuse.
Reset circuit breaker.
Check house lights. Call local Electric Company.
•
•
Power outage.
•
•
Refrigerator runs too
much or too long.
Room or outside weather is
hot.
It’s normal for the refrigerator to work longer under
these conditions.
•
Refrigerator has recently been
disconnected for a period of
time.
•
It takes 8-12 hours for the refrigerator to cool down
completely.
•
•
•
Automatic ice maker is
operating.
Doors are opened too
frequently or too long.
Fresh Food/freezer door may
be slightly open.
•
•
•
Ice maker operation causes refrigerator to run slightly
more.
Warm air entering the refrigerator causes it to run
more. Open doors less often.
Ensure refrigerator is level. Keep food and containers
from blocking door. See PROBLEM section
OPENING/CLOSING OF DOORS/DRAWERS.
Set Fresh Food control to warmer setting until
refrigerator temperature is satisfactory. Allow 24 hours
for temperature to stabilize.
Clean or change gasket. Leaks in door seal will cause
refrigerator to run longer in order to maintain desired
temperatures.
•
•
Freezer control is set too cold
(control found in Fresh Food
section).
Fresh Food/freezer gasket is
dirty, worn, cracked, or poorly
fitted.
•
•
•
•
Condenser is dirty.
•
•
Clean condenser. See Care & Cleaning Chart in Care
and Cleaning section.
Compressor goes off and
on frequently.
Thermostat keeps the
refrigerator at a constant
temperature.
This is normal. Refrigerator goes on and off to keep
temperature constant.
TEMPERATURES ARE TOO COLD
Freezer temperature too
cold. Fresh Food
temperature is satisfactory.
•
Freezer control is set too cold.
•
•
Set freezer control to a warmer setting. Allow 24 hours
for temperature to stabilize.
Fresh Food temperature
too cold. Freezer
•
Fresh Food control is set too
cold.
Set fresh food control to a warmer setting. Allow 24
hours for temperature to stabilize.
temperature is satisfactory.
Food stored in drawers
freezes.
•
•
Fresh Food control is set too
cold.
•
•
See solution above.
Food stored in Meat
Keeper freezes (some
models).
Meat Keeper Temperature
Control set too cold.
Adjust Meat Keeper Temperature Control to a lower
setting. (Meat should be stored at a temperature just
below the freezing point for maximum fresh storage
time. It is normal for ice crystals to form due to the
moisture content of meat.)
Digital temperature
displays are flashing.
•
Electronic control system has
detected a performance
problem.
•
Call your service representative, who can interpret any
messages or number codes flashing on the digital
displays.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFOREYOU CALL (CONTINUED)
PROBLEM
CAUSE
CORRECTION
TEMPERATURES ARE TOO WARM
Freezer/Fresh Food
temperature is too warm.
•
•
•
Doors are opened too
frequently or too long.
Door is slightly open.
•
•
•
Warm air enters the refrigerator whenever the door is
opened. Open the door less often.
See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.
Clean condenser. See Care & Cleaning Chart in Care
and Cleaning section.
Condenser is dirty.
Freezer temperature is too
warm. Fresh Food
temperature is satisfactory.
•
•
•
Freezer control is set too
warm.
•
•
•
Set freezer control to a colder setting. Allow 24 hours
for temperature to stabilize.
Fresh Food temperature is
too warm. Freezer
temperature is satisfactory.
Fresh Food control is set too
warm.
Set fresh food control to a colder setting. Allow 24
hours for temperature to stabilize.
Temperature in the Meat
Keeper is too warm (some
models).
Meat Keeper Temperature
Control is set too warm.
Adjust Meat Keeper Temperature Control to a colder
setting.
WATER/MOISTURE/FROST INSIDE REFRIGERATOR
Moisture collects on inside
of refrigerator walls.
•
•
•
Weather is hot and humid.
Door is slightly open.
•
•
•
The rate of frost buildup and internal sweating
increases.
See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.
Door is opened too often or too
long.
Open door less often.
•
•
Open containers.
•
•
Keep containers covered.
Water collects on bottom
side of drawer cover.
Vegetables contain and give
off moisture.
It is not unusual to have moisture on the bottom side of
the cover.
•
•
Move humidity control (some models) to lower setting.
Water collects in bottom of
drawer.
•
Washed vegetables and fruit
drain while in the drawer.
Dry items before putting them in the drawer. Water
collecting in bottom of drawer is normal.
WATER/MOISTURE/FROST OUTSIDE REFRIGERATOR
Moisture collects on
outside of refrigerator or
between doors.
•
•
Weather is humid.
•
•
This is normal in humid weather. When humidity is
lower, the moisture should disappear.
See PROBLEM section OPENING/CLOSING OF
DOORS/DRAWERS.
Door is slightly open, causing
cold air from inside refrigerator
to meet warm air from outside.
AUTOMATIC ICE MAKER
Ice maker is not making
any ice.
•
Ice maker wire signal arm is in
the “up” or OFF position.
•
Move wire signal arm to the “down” or ON position.
(side mounted)
•
•
Turn power switch to On (“I”) position. (rear mounted)
Turn on household water line valve.
•
•
Ice maker power switch is Off.
Household water line valve is
not open.
•
Remove small cube from ice maker. The ice & water
filter cartridge may be clogged. Replace filter
cartridge.
•
Ice maker has small cube
caught in mechanism.
•
•
See PROBLEM section TEMPERATURES ARE TOO
WARM.
Turn off household water line valve. Remove valve.
Ensure that valve is not a self-piercing saddle valve.
Clean valve. Replace valve if necessary.
•
•
Freezer is not cold enough.
Saddle valve on cold water
pipe is clogged or restricted by
foreign material.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFOREYOU CALL (CONTINUED)
CAUSE CORRECTION
PROBLEM
AUTOMATIC ICE MAKER (CONTINUED)
Ice maker is not making
enough ice.
•
Ice maker is producing less ice
than you expect.
•
Side mounted ice maker should produce 4 to 4.5
pounds (approximately 4 quarts) of ice every 24
hours. A rear mounted ice maker should produce 3
to 4 pounds (approximately 3½ quarts) of ice every
24 hours. Extra Ice option should produce 25% to
50% more ice every 24 hours.
•
•
•
Freezer is not cold enough.
•
•
•
See PROBLEM section TEMPERATURES ARE
TOO WARM.
Turn on household water line valve.
Household water line valve is
not completely open.
Check to see if water
dispenser is dispensing slower
than normal.
If it is, replace the ice & water filter cartridge.
Ice maker will not stop
making ice.
•
Ice maker wire signal arm is
being held down by some item
in the freezer.
•
Move item and release wire signal arm. Remove
any ice cubes that are frozen together over the wire
signal arm.
Ice cubes are freezing
together.
•
•
Ice cubes are not being used
frequently enough.
Ice cubes are hollow (partially
frozen cubes with water
inside).
•
•
Remove ice container and discard ice from
container. Ice maker will produce fresh supply.
The ice & water filter cartridge may be clogged.
Replace filter cartridge.
•
Freezer control is set too
warm.
•
Set freezer control to colder setting. Allow 24 hours
for temperature to stabilize.
•
•
Very little food in freezer.
•
•
Add more food to freezer.
Ice has bad odor and
taste.
Ice has picked up odor or
flavor from strong food stored
in refrigerator or freezer.
Water running to ice maker
has poor taste or odor.
Cover foods tightly. Discard stale ice. Ice maker will
produce fresh supply.
•
•
•
•
Add filter to water supply line. Consult a water
purifying company.
Discard stale ice.
Ice not used frequently enough.
ICE DISPENSER
Dispenser will not
dispense ice.
•
•
Ice storage container is empty.
•
•
When the first supply of ice is dropped into the
container, the dispenser should operate.
Turn freezer control to a higher setting so that ice
cubes will be made. When first supply of ice is
made, dispenser should operate.
Freezer temperature is set too
warm.
•
Household water line valve is
not open.
•
Open household water line valve. Allow sufficient
time for the ice to be made. When ice is made, the
dispenser should operate.
•
•
Freezer door is not closed.
Ice dispensing arm has been
held in for more than 4-5
minutes.
•
•
Ensure freezer door is closed.
Motor is overloaded. Motor overload protector will
reset in approximately 3 minutes. Ice can then be
dispensed.
Ice dispenser is
jammed.
•
•
Ice has melted and frozen
around auger due to infrequent
use, temperature fluctuations,
and/or power outages.
•
•
Remove ice container, thaw, and empty the
contents. Clean container, wipe dry, and replace in
proper position. When new ice is made, dispenser
should operate.
Ice cubes are jammed
Remove ice cubes that are jamming the dispenser.
between ice maker and back
of ice container.
•
•
Ice cubes are frozen together.
•
•
Use the dispenser often so that cubes do not freeze
together.
The ice & water filter cartridge could be clogged.
Replace the filter cartridge. Dispensing system
operates best at 30 – 100 psi water pressure. Well
water pressures should fall within this range.
Ice cubes are hollow
(partially frozen cubes with
water inside).
28
Download from Www.Somanuals.com. All Manuals Search And Download.
BEFOREYOU CALL (CONTINUED)
PROBLEM
CAUSE
CORRECTION
WATER DISPENSER
Dispenser will not
dispense water.
•
Household water line valve is not
open.
Freezer door is not closed.
Ice & water filter cartridge is clogged.
•
Open household water line valve. See PROBLEM
section ICE MAKER IS NOT MAKING ANY ICE.
Ensure that freezer door is closed.
Replace filter cartridge.
Push filter in until you hear a “click”. Filter should be
flush with cabinet.
•
•
•
•
•
•
Front filter not fully installed, if
equipped
Water has an odd
taste and/or odor.
•
•
•
Water has been in the tank for a
period of time.
Unit not properly connected to cold
water line.
Tubing used in the household water
supply and installation may affect
water taste and odor.
•
•
•
Draw and discard 10 – 12 glasses of water to freshen
the supply and completely rinse out the tank.
Connect unit to cold water line that supplies water to
the kitchen faucet.
For best results, use copper tubing for water
connections.
•
•
Water has a high mineral content.
•
•
Contact water treatment plant for help.
Water pressure is
extremely low.
Cut-off and cut-on pressures are too
low (well systems only).
Reverse osmosis system is in
regenerative phase.
Have someone turn up the cut-off and cut-on pressure
on the water pump system (well systems only).
It is normal for a reverse osmosis system to be below
20 psi during the regenerative phase.
•
•
ODORS IN REFRIGERATOR
Interior is dirty.
•
•
Interior needs to be cleaned.
•
•
See Care & Cleaning Chart in Care and Cleaning
section.
Cover food tightly.
Food with strong odors is in
refrigerator.
OPENING/CLOSING OF DOORS/DRAWERS
Door(s) will not close.
•
•
Door was closed too hard, causing
other door to open slightly.
Refrigerator is not level. It rocks on
the floor when moved slightly.
•
•
Close both doors gently.
Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.
•
Ensure floor is level and solid, and can adequately
support the refrigerator. Contact a carpenter to correct
a sagging or sloping floor.
•
Refrigerator is touching a wall or
cabinet.
Drawers are difficult
to move.
•
•
Food is touching shelf on top of
drawer.
Track that drawers slide on is dirty.
•
•
Keep less food in drawer.
Clean drawer, rollers, and track. See Care & Cleaning
Chart in Care and Cleaning section.
LIGHT BULB IS NOT ON
Light bulb is not on.
•
•
•
Light bulb is burned out.
Light switch is stuck.
•
•
•
See Replacing Light Bulbs in Care and Cleaning
section.
Light switch is located on side of refrigerator and
freezer liners.
See PROBLEM section RUNNING OF
REFRIGERATOR.
No electric current is reaching
refrigerator.
IF YOU HEAR (electronic models only)
5 beeps
•
A door has been left open for 5
minutes or more.
•
•
These beeps will repeat once every minute until the
door has been closed. This is normal for the “Door
Ajar” alarm.
3 beeps
•
The refrigerator has experienced a
loss of power or a low voltage
condition.
This is normal when “Power-On-Reset” is activated.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
|