Creda Newera Profile and Profile Plus Panel Heaters
Installation and Operating Instructions
Model with
controls white
Model with controls
silver
Model with no
controls white
Dimensions
(mm)
Wattage (W)
500
NPP50 75-773001
NPP100 75-773002
NPP150 75-773003
NPP200 75-773004
NPP50S 75-773011
NPP100S 75-773012
NPP150S 75-773013
NPP200S 75-773014
NP50 75-772901
NP100 75-772902
NP150 75-772903
NP200 75-772904
442 x 430 x 80
680 x 430 x 80
680 x 430 x 80
852 x 430 x 80
1000
1500
2000
The Newera Profile panel heater range is designed for wall mounting on the wall brackets supplied. It
should only be operated when in the upright position as shown in diagram C.
All models are protected against moisture ingress to IPX4 standard.
All models, except those with no controls, are fitted with a 7-day digital programmer.
Installation:
Before connecting the heater, check that the supply voltage is the same as that stated on the rating label.
When selecting the position for the heater to be installed, consideration should be given to ensure that there
are no obstructions closer than the dimensions given in Diagram C. The bracket for the heater should be
fitted in accordance with the method detailed in the associated diagrams. The heater must not be located
below a socket outlet or connection box.
Care must be exercised when fitting the heater onto the bracket. Pressure should only be applied to
the ends of the heater and not to the grille area.
The electrical installation must be carried out by a competent electrician and in accordance with the current
Electrical Wiring Regulations (BS7671) and/or local regulations.
The heater is fitted with a length of flexible cable for connection to the fixed wiring of the premises via a
suitable connection box positioned adjacent to the heater.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
A means for disconnection in all poles must be incorporated in the fixed wiring in accordance with
the wiring rules.
WARNING – THIS APPLIANCE MUST BE EARTHED
WARNING – In order to avoid overheating, do not cover the heater.
Download from Www.Somanuals.com. All Manuals Search And Download.
View of Controls
Diagram D
No Controls Models – 75-772901, 75-772902, 75-772903, 75-772904 and 75-772905
These models can be installed in association with a separate room thermostat control.
Bracket release for cleaning
For safety, the heater should be switched off at the mains before proceeding. To release
the panel heater from the bracket, the rear catch must be pressed down while pulling the
heater forward gently. It is recommended to use a narrow tool for this purpose. A pencil
or small screwdriver would be a suitable tool. Diagram D shows the procedure for
releasing the heater from the bracket.
When replacing the heater on the bracket, firstly engage the heater on to the bottom hooks
and then press the heater on to the catch. It is recommended to press the heater at the
ends and not to the grille area.
Download from Www.Somanuals.com. All Manuals Search And Download.
The Panel - How it works
A heating element within the metal case warms its front face for direct radiation into the room and a gentle circulation of
warm air around the room. The built-in thermostat with its adjustment knob located behind the controls door, controls
the room temperature by sensing this from the air passing upwards through the panel. The knob selection provides
settings from 1 to 6 and each increase in number equates to approximately 7°C temperature difference. Position 1
represents 7°C and would be used for frost protection when the property is not occupied. Position 3 represents 21°C
and is the normal comfort position.
NOTE – Should your heater fail to come on when the thermostat knob is at a low setting, this may be due to the
temperature of the room being higher than the thermostat setting.
Timer/Programmer
A digital timer/programmer is built into the product and is situated behind the controls door. This will control the
operation of the heater for the time periods set at the thermostat setting.
Setting up
If, at any time during setting, a period of approximately 7 seconds passes with no button pressed then the timer reverts
to the clock display and saves the settings thus far.
To set the clock,
firstly press the left button below where it says “SETUP” on the display. Five options will be
displayed on the right side of the display. These are PROG, DOWN, CLOCK, SUMMER and RANDOM. PROG will be
flashing at this time. Press the “+” button twice to move the flashing to “CLOCK”, and then press the left button to
“AFFIRM” the choice. The hour display will now be flashing and pressing the + or – buttons will set the display to the
required setting. Then press the AFFIRM button and the minutes display will be flashing and again the + and – buttons
will set the display to the required setting. Press the AFFIRM button and the day display will be flashing and the + and –
button will set the day to the required setting. Press the AFFIRM button to end the clock setting and return to the clock
display.
To set the Program,
firstly press the left button below where it says “SETUP” on the display. Five options will be
displayed on the right side of the display. These are PROG, DOWN, CLOCK, SUMMER and RANDOM. PROG will be
flashing at this time. Press the AFFIRM button and the 01ON display will be flashing. Press the AFFIRM button and the
hour display will flash and be adjustable by the + and – buttons. Pressing AFFIRM will move the display to the minutes,
and then to the days. The days have special groupings that can be selected by pressing the + and - buttons. They are
MO TU WE TH FR , SA SU , MO TU WE TH FR SA , MO WE FR , TU TH SA , MO TU WE , TH FR SA ,
ALL DAYS and individual days. Make your selection and press AFFIRM. The 01ON display will flash. Pressing the +
button will advance the display to 01OFF and the same procedure should be followed for setting the OFF time
remembering to use the same day selection. The procedure should be followed through to complete your programming
requirements up to maximum step 12OFF. Any unwanted steps may be left blank.
Manual Over-ride
The timer can be over-ridden at any time by pressing the right-hand button until the display
shows the required mode ALWAYS ON or ALWAYS OFF. The timer must be returned to the PROG position for the
timer and its programs to be active.
Summer Setting
For setting the clock forward 1 hour for summer, press SETUP and select Summer on the
display then press +. To unset the summer setting, repeat the procedure.
Down Timer
The heater can be set to be ON for a fixed time by selecting DOWN from the SETUP screen
and using the + and – buttons to set the required hours. Then press AFFIRM and set the minutes followed by AFFIRM.
The heater will then operate until the time expires.
April 2005
577 2003 02A
Download from Www.Somanuals.com. All Manuals Search And Download.
|