DTT 3 5 0 0 Dig it a l
User Guide
On-line Version
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety & Regulatory Information
The following sections contain notices for various countries:
Notice for the USA
Modifications
Declaration of Conformity
Compliance
FCC Part 15: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, this
notice is not a guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try one or more of the
following measures:
Any changes or modifications not expressly approved by
the grantee of this device could void the user’s authority
to operate the device.
According to the FCC96 208 and ET95-19
This product conforms to the following Council Directive:
Name:
Creative Labs Inc.
•
Directive 89/ 336/ EEC, 92/ 31/ EEC (EMC), 73/ 23/
EEC (LVD)
Address:
1901 McCarthy Boulevard
Milpitas, CA. 95035
United States
Notice for Canada
This apparatus complies with the Class B limits for radio
interference as specified in the Canadian Department of
Communications Radio Interference Regulations.
Tel: (408) 428-6600
declares under its sole responsibility that the product
Trade Name:
Creative Labs/
CambridgeSoundWorks
CSW3600
Cet appareil est conforme aux normes de CLASSE “B”
d’interference radio tel que spe’cifie’ par le Ministère
Canadien des Communications dans les règlements
d’interfèrence radio.
Model Number:
has been tested according to the FCC / CISPR22/85
requirement for Class B devices and found compliant
with the following standards:
EMI/ EMC: ANSI C63.4 1992, FCC Part 15 Subpart B
Complies with Canadian ICES-003 Class B.
•
•
Reorient or relocate the receiving antenna.
Increase the distance between the equipment and
receiver.
Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV
technician.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
•
•
1.
This device may not cause harmful interference,
and
2.
This device must accept any interference received,
including interference that may cause undesirable
operation.
WARNING: To prevent fire or
shock hazard, do not expose this
appliance to rain or moisture.
CAUTION: To comply with the limits for the Class B
digital device, pursuant to Part 15 of the FCC Rules, this
device must be installed with computer equipment
certified to comply with the Class B limits.
Ce matériel est conforme à la section 15 des régles FCC.
Son fonctionnement est soumis aux deux conditions
suivantes:
1.
2.
Le matériel ne peut étre source d’interférences et
Doit accepter toutes les interférences reques, Y
compris celles pouvant provoquer un
fonctionnement indésirable.
All cables used to connect the computer and peripherals
must be shielded and grounded. Operation with non-
certified computers or non-shielded cables may result in
interference to radio or television reception.
Important Notice
The serial number for the DTT3500 Digital is located on
the Decoder Amplifier. Please write this number down
and keep it in a secure area. This is for your security.
Compliance Manager
Creative Labs, Inc.
August 10, 2000
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
READ INSTRUCTIONS – All safety and
operating instructions should be read
before the product is operated.
RETAIN INSTRUCTIONS – The safety and
operating instructions should be retained
for future reference.
HEED WARNINGS – All warnings on the
product and in the operating instructions
should be adhered to.
to prevent it from overheating. These
openings must not be blocked or covered.
The openings should never be blocked by
placing the product on a bed, sofa, rug, or
other similar surface. This product should
not be placed in a built-in installation such
as a bookcase or rack unless proper
ventilation is provided or Cambridge
SoundWorks’ instructions have been
adhered to.
HEAT – This product should be situated
away from heat sources such as radiators,
heat registers, stoves, and other products
(including amplifiers) that produce heat.
POWER SOURCES – This product should be
operated only from the type of power source
indicated on the marking label. If you are
not sure of the type of power supply to your
home, consult your product dealer or local
power company. For products intended to
operate from battery power or other
sources, refer to the operating instructions.
POLARIZATION – This product may be
equipped with a polarized alternating-
current line plug (a plug having one blade
wider than the other). This plug will fit into
the power outlet only one way. This is a
safety feature. If you are unable to insert
the plug fully into the outlet, try reversing
the plug. If the plug should still fail to fit,
contact your electrician to replace your
obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
convenience receptacles, and the point
where they exit from the product.
LIGHTNING – For added protection for this
product during a lightning storm, or when
it is left unattended and unused for long
periods of time, unplug it from the wall
outlet. This will prevent damage to the
product due to lightning and power-line
surges.
OVERLOADING – Do not overload wall
outlets, extension cords, or integral
convenience receptacles as this can result
in a risk of fire or electric shock.
OBJECT AND LIQUID ENTRY – Never push
objects of any kind into this product
through openings as they may touch
dangerous voltage points or short out parts
that could result in a fire or electric shock.
Never spill liquid of any kind on the
product.
SERVICING – Do not attempt to service this
product yourself, as opening or removing
covers may expose you to dangerous
voltage or other hazards. Refer all servicing
to qualified service personnel.
DAMAGE REQUIRING SERVICE – Unplug
this product from the wall outlet or other
power source and refer servicing to
qualified service personnel under the
following conditions:
or exhibits a distinct change in
performance.
e) If the product has been dropped or
damaged in any way.
REPLACEMENT PARTS – When
replacement parts are required, be sure the
service technician has used replacement
parts specified by Cambridge SoundWorks
or have the same characteristics as the
original parts. Unauthorized substitutions
may result in fire, electric shock, or other
hazards.
SAFETY CHECK – Upon completion of any
service or repairs to this product, ask the
service technician to perform safety checks
to determine that the product is in proper
operating condition.
FOLLOW INSTRUCTIONS – All operating
and use instructions should be followed.
CLEANING – Unplug this product from the
wall outlet or other power source before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
ATTACHMENTS – Do not use attachments
not recommended by Cambridge
SoundWorks as they may cause hazards.
WATER AND MOISTURE – Do not use this
product near water; for example, near a
bath tub, wash bowl, kitchen sink, or
laundry tub; in a wet basement; or near a
swimming pool; and the like.
ACCESSORIES – Do not place this product
on an unstable cart, stand, tripod, bracket,
or table. The product may fall, causing
serious injury to a person, and serious
damage to the product. Use only with a
cart, stand, tripod, bracket, or table
recommended by Cambridge SoundWorks,
or sold with the product. Any mounting of
the product should follow the
WALL OR CEILING MOUNTING – The
product should be mounted to a wall or
ceiling only as recommended by Cambridge
Soundworks.
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled into, or objects
have fallen onto the product.
c) If the product has been exposed to rain
or water.
d) If the product does not operate normally
by following the operating instructions;
manufacturer’s instructions, and should
use a mounting accessory recommended by
Cambridge SoundWorks.
VENTILATION – Slots and openings in the
cabinet are provided for ventilation, to
ensure reliable operation of the product and
POWER-CORD PROTECTION – Power-
supply cords should be routed so that they
are not likely to be walked on or pinched by
items placed upon or against them, paying
particular attention to cords at plugs,
Download from Www.Somanuals.com. All Manuals Search And Download.
-
Contents
Introduction.........................................................................................................1
Inventory ............................................................................................................2
Recommended Signal Sources ...........................................................................2
Installation Sequence.........................................................................................3
Speaker System Connections .............................................................................3
Speaker System Connection Diagram................................................................4
Signal Source Connections.................................................................................5
Signal Source Connection Diagram....................................................................6
Speaker Cable and Stand Installation................................................................7
Mounting Speakers ............................................................................................8
Speaker Placement .............................................................................................9
Decoder Amplifier Placement ...........................................................................12
Decoder Amplifier Functions............................................................................13
Surround Reference..........................................................................................15
Multiple Connections........................................................................................17
Applications Guide ...........................................................................................18
Playback Levels ................................................................................................21
Specifications....................................................................................................21
EAX...................................................................................................................21
1-Year Limited Warranty..................................................................................22
Technical Support.............................................................................................22
DTT3500 Digital
Download from Www.Somanuals.com. All Manuals Search And Download.
0
Introduction
hank you for purchasing
channel audio. It’s ready for the new
era of DVD-based games.
Cambridge SoundWorks
1–800–FOR–HIFI
DTT3500 Digital by Cambridge
SoundWorks. DTT3500 Digital
Also included is Creative Multi
Speaker Surround (CMSS), which lets
you hear all of your favorite stereo
program material with a new and
exciting three-dimensional quality.
DTT3500 Digital comes equipped
with an I.R. Remote Control,
providing wireless control over a
variety of audio functions.
The Memory Retention feature of
the DTT3500 Digital system
(1
8:00
–
A.
800
M. – 12 Midnight,
Eastern time
1:00 M. – 4:00
–367–4434),
T
lets you experience the full potential
®
of Dolby Digital multichannel sound
P.
A.M.
from your DVD player or game
console, with a dynamic output that
rivals a component home theater
system. It processes both Dolby
Digital and Dolby Surround program
material.
DTT3500 Digital includes an
OPTICAL connection to enhance the
connectivity and usability to any
devices with OPTICAL output.
DTT3500 Digital also includes a
DIGITAL DIN input which supports
discrete 5.1-channel output.
Greenwich Mean Time
Outside US:
Tel: 617–332–5936
Fax: 617–527–3194
or e-mail us at
remembers the last used user settings
in standby mode.
DTT3500 Digital offers up to 6-
channel discrete audio support for
®
®
Microsoft DirectSound 3D and its
other derivatives. In some of today’s
best CD-based action games,
DTT3500 Digital can decode the
Dolby Digital cut-scenes while
offering enveloping positional multi-
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Recommended Signal Sources
Inventory
shipping damage. If there is any, do not
install or use the system. For advice, call
the store where you made your purchase
or call Creative Technology Ltd.
technical support. Save the shipping
carton and inserts in case you have to
transport the system later. All of the
items shown in the illustration below
should be included with your system. If
anything is missing, notify the retailer.
The DTT3500 Digital supports many
signal source inputs, both analog and
digital. For example:
processing, including front and
the Sound Blaster AWE series can
also be used with the DTT3500
Examine each unit carefully for
rear 2-channel minijack line
outputs (like Sound Blaster Live!
series or Creative Labs Sound
Blaster PCI series).
Digital
.
1. DVD players with Dolby Digital
(AC-3) optical outputs. DVD
4. Game consoles like the
PlayStation 2TM using the Optical
or Analog Line In connections.
Sound Blaster Live! owners
should utilize the exclusive
Digital DIN connection to hear the
clearest digital audio available.
3. Conventional 2-channel sound
cards such as Sound Blaster 16 or
players with coaxial outputs (for
example, the Creative labs PC-
DVD Encore) may also be used.
2. Sound cards that support
®
DirectSound 3D sound
Minijack to DIN Cable
Screw
SPDIF Cable (RCA to RCA)
Stereo to Dual RCA Cable
3m Speaker Cable (4)
(for Center Speaker Stands)
Monitor Stand
(for Center Speaker)
15V 4A DC
Power Adapter
Decoder Amplifier
Subwoofer
Support
Extends (18)
Strips of Rubber Feet (2)
5m Speaker Cable (2)
Optical Cable
Feet (6)
Supports (6)
Desktop Stand
Center Speaker
Satellites (4)
Remote Control
(for Center Speaker)
Screws and Plastic Anchors (2)
Identification Labels
Tandem Audio Cable
SPDIF DIN Cable
Dual Female-to-Female
RCA Adapter
Holder/Cap (2)
“AA”- Size Battery (2)
Desktop Stand (4)
(for Satellites)
Frames (2)
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Installation Sequence
Speaker System Connections
1. Read all of the instructions before
installing the speaker system.
2. Attach the provided stand to the
Decoder Amplifier if you wish to
place the unit vertically. For more
details see “Decoder Amplifier
Placement” on page 12.
Speaker Connections
Power Adapter Connections
Insert one satellite’s plug into the
corresponding Speaker Output on the
Decoder Amplifier. Repeat this
process for the remaining satellites,
center speaker and subwoofer. For
more details see “Speaker Cable and
Stand Installation” on page 7.
If substituting a powered
Insert the small DC connector into the
15V DC IN jack on the back of the
Decoder Amplifier. Insert the Power
Adapter’s AC plug into an appropriate
receptacle.
3. Connect the Satellites, Center
Speaker, and Subwoofer to the
Decoder Amplifier.
4. Connect the Dolby Digital output
of your digital program source to
the coaxial and/or optical Dolby
Digital input of the Decoder
Amplifier.
5. Connect your normal audio signal
sources via the Analog Line In
inputs. An owner of a Sound
Blaster Live! sound card with a
Digital DIN output should use the
supplied cable to connect it to the
Digital DIN input instead.
Note: Set the Decoder Amplifier to
standby mode before unplugging or
turning off the power supply.
subwoofer, connect it to the
Subwoofer Line Out. For more details
see “Substituting a powered
speakers.
subwoofer” on page 11.
permanent.
6. Using the placement instructions
as a guide, position the Satellites,
the Center Speaker and
Subwoofer. Install the Desktop
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Signal Source Connections
miniplugs to the Rear Out minijack
output of your sound card (if present)
and to the Rear minijack input of the
Decoder Amplifier.
Dolby Digital source
For devices with optical output
Connect the Dolby Digital/SPDIF
output of your signal source to the
Connect the optical output of these
devices (e.g. CD or MD players) to the
Decoder Amplifier’s Dolby Digital (AC- OPTICAL input with the Optical
3) / PCM Audio Inputs COAXIAL or
OPTICAL jack using the SPDIF Cable
Cable.
For Sound Blaster Live! sound
cards with Digital Out output
(RCA to RCA) or the Optical Cable
.
Game consoles
Connect the sound card’s Digital Out
output to the Digital DIN input with
the Minijack to DIN Cable and the
Connect the optical output of the
game console (e.g. PlayStation2) to
the OPTICAL input with the Optical
Cable
.
SPDIF DIN Cable.
Use the Stereo to Dual RCA Cable
and the Dual Female-to-Female RCA
Adapter to connect to the game
console’s RCA output through the
multiple A/V plug. Then connect the
miniplug end of the Stereo to Dual
RCA Cable to the FRONT jack of the
Decoder Amplifier.
For DIN Bracket bundled with
Live! Drive IR
Connect its Digital DIN output to the
DIGITAL DIN input with the SPDIF
DIN Cable.
For all other sound cards
Use the Tandem Audio Cable
.
Connect the lime-green stereo
miniplugs to the Line Out minijack
output of your sound card and to the
FRONT minijack input of the Decoder
Amplifier. Connect the black stereo
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Signal Source Connection Diagram
Dual Female-to-Female RCA
DIGITAL OUT
Red
Stereo to Dual RCA Cable
Digital Output (Eg. PC-DVD Encore)
White
LINE OUT
REAR OUT
SPDIF Cable
(RCA to RCA)
LINE OUT
Game Console
4-Ch Sound Card Output
(Eg. Sound Blaster Live!)
Lime-Green
Black
2-Ch Sound Card Output
(Eg. Sound Blaster AWE64)
Lime-Green
OPTICAL OUTPUT
COAXIAL OUTPUT
Optical Cable
Tandem Audio Cable
DIGITAL OUT
OR
OR
Digital Output (Sound Blaster 5.1 Sound Card)
DVD Player
CD Player
Minijack to DIN Cable
Lime-Green
Black
DIGITAL OUT
Digital Output
(Bundled with Live! Drive IR)
SPDIF DIN Cable
MD Player
Download from Www.Somanuals.com. All Manuals Search And Download.
6
taking up any slack in the cable
as required.
leaflet.
A
Speaker Cable
and Stand
2. To use this Satellite in the front
left position, remove the backing
from the small, round “L” label
and apply it to the back of the
Satellite (see Diagram A).
3. Remove the backing from the
remaining, longer “L” label and
wrap it around the opposite end
of the Speaker Cable near the RCA
plug.
4. Place the Satellite in the front left
position.
5. Repeat this process using another
3 meter Speaker Cable for the
front right Satellite, using the “R”
labels.
6. Connect another 3 meter Speaker
Cable to the Center Speaker. Use
the “C” (center) labels. For details
on attaching Center Speaker
stands, see “Center Speaker Stand
Installation” on page 8.
7. Use the RS and LS labels (right
and left surround) and 5 meter
Speaker Cables for the rear
Satellites.
the Subwoofer.
Installation
Speaker Cable Usage
connection hole.
Insert the bare end of the cable
into the exposed hole, then release
the tab to lock the cable in place.
Connect cables with red bands to
red tab connectors, and unmarked
wires to black tab connectors.
Speaker Cable Installation
Typically, the 3 meter (5 feet) Speaker
Cables will connect the front
Socket
Attachment Arm
Satellites and the Center Speaker to
the Decoder Amplifier and the 5 meter
(9 feet) Speaker Cables will connect
the rear Satellites to the Decoder
Amplifier. A panel of twelve self-
adhesive labels is provided to identify
each Satellite and Subwoofer and the
opposite end of the cable connected to
a Satellite and Subwoofer.
Notes: Matching red cables to red
tabs and unmarked cables to black
tabs insures the speakers all play
“in phase”. “Out-of-phase”
connections will do no electrical
harm, but the overall sound quality
will be greatly reduced. You can
substitute regular 18 gauge speaker
cable to create longer cables, if
needed. The 5 meter cables may
also be used for the front satellites
if required.
1. Identify a 3 meter Speaker Cable.
Most often, a Satellite will be
used with a Desktop Stand. In
this case, thread the bare cable
end of a 3 meter Speaker Cable
through the hole in the Desktop
Stand. Connect this end to a
Satellite (as shown in Diagram
A). Carefully insert the Desktop
8. If you wish to use the Floor
Stands with the rear Satellites,
Stand’s attachment arm into the
socket in the back of the Satellite,
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Center Speaker Stand
Installation
Mounting Speakers
B
satellite. The rubber pads will
cushion the satellites from any
vibration and help keep them in
position.
Unlike the Desktop Stand (for
Satellites), the stands for the Center
Speaker are of the screw-in type.
1. Align the Attachment Arm to
the Center Speaker (see
Screw Mounting
Attachment Arm
Mounting the rear satellites on side
walls will give you superior surround
effects.
For a secure installation, mount the
rear satellites only on walls that are
structurally sound.
6. Slip the keyhole of each rear
satellite onto a protruding screw
to complete the installation.
Diagram B)
.
2. Use the screw provided to
connect the Attachment Arm to
the Center Speaker.
1. Place the following near you: rear
satellites, screws, plastic anchors
and rubber pads (supplied). You
will also need a drill and hammer.
2. Mark the wall where each rear
satellite screw will be. Position
the speakers behind you and
C
slightly above ear level.
3. Drill a hole about 2 cm (1 inch)
deep into each wall. Tap a plastic
anchor into the hole until it is
flush with the wall (see Diagram
C).
4. Screw a M5 x 25 mm screw into
each anchor, leaving about
0.5 cm (¼ inch) of the screw
protruding.
5. Apply four rubber pads on the
corners at the back of each rear
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Speaker Placement
It directs the sound down towards the
listener (see Diagram E).
Use the Center Speaker Desktop
Stand to position a Center Speaker in
front of the T.V. or monitor. It directs
the sound up towards the listener
(see Diagram F).
The Front Satellites
The Center Speaker
The left front and right front
Satellites play stereo music, the off-
screen sounds of video playback and
the front channels of 4-channel
games.
These Satellites should be placed to
the sides of your T.V. or monitor. Try
to form an equilateral triangle with
your head and the satellites (see
Diagram D). Be sure to have a clear
line of sight from your listening
position to these Satellites.
The Center Speaker provides the on-
screen effects and dialog in Dolby
Digital, Dolby Surround or Creative
Multi Speaker Surround modes. It
should be placed as close to the
center of your T.V. or monitor as
possible.
There are many mounting
possibilities. The Center Speaker can
be placed on top of the T.V or monitor
by using the provided Monitor Stand.
E
F
D
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Satellites.
The rear Satellites may be installed
on their convenient Floor Stands. The
stands should be positioned to the
left and right of your listening
position (see Diagram H).
Larger T.V. consoles or desktops can
accommodate both front and
surround pairs of Satellites. Try the
extreme corners of a console or desk
using the Desktop Stands (see
Diagram I).
After you have positioned the rear
Satellites, use the TEST function on
the Remote Control to make sure each
speaker can be heard clearly.
The Rear Satellites
The rear Satellites provide the
surround effects in Dolby Digital,
Dolby Surround or Creative Multi
Speaker Surround modes. They also
produce the discrete rear sounds of 4-
channel sound cards.
Wall Anchors provided, see
“Mounting Speakers” on page 8.
Any rear Satellite placement to the
left and right side of the listening
position will also provide strong
directional and surround effects.
5 meters (16 feet) of cable is
provided with the two remaining
Satellites for more flexibility in rear
channel placement. The rear
Satellites may be placed in any
convenient sites alongside the
listener, including sites slightly
forward of the listening location. The
rear Satellites do not have to be at
H
I
G
Download from Www.Somanuals.com. All Manuals Search And Download.
10
The Subwoofer
Substituting a powered
The Subwoofer’s optimum position is
on the floor against the wall. The
closer the Subwoofer is to a corner,
the stronger the maximum bass
output. We strongly recommend
placing the Subwoofer on the floor
(see Diagram J). Leave at least 5 cm
(2 inches) of space between the
Subwoofer face and a wall. Position
the Subwoofer so that it’s connection
panel is facing a wall, shielded from
inadvertent contact. The Subwoofer is
not magnetically shielded, so position
it at least 46 cm (18 inches) away
from the T.V. or computer monitor.
subwoofer
You may substitute a powered
subwoofer for the subwoofer that
comes with the DTT3500 Digital
.
Connect its line level input (typically
an RCA jack) to the dedicated
Subwoofer Line Out on the back of
the Decoder Amplifier, using a
shielded audio cable with RCA plugs
on each end. Refer to the powered
subwoofer’s User Manual for
adjustment procedures.
J
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Decoder Amplifier Placement
The Decoder Amplifier can be placed
Model Variations
Decoder Amplifier Stand
Horizontal Placement
on the desktop, a shelf or any site
There are two models of the Decoder
Amplifier.
If placing the unit vertically, attach
the provided stand to the base of the
Decoder Amplifier (see Diagram K).
Place the Decoder Amplifier
horizontally if there is adequate
desktop space, (see Diagram L).
that makes the controls convenient.
The Power Adapter cord must be
able to reach from the Decoder
Amplifier back panel to your AC
power receptacle.
If you have purchased the
horizontal version please ignore the
following sections. Other than the
changeable face plate feature, all
functions remain the same.
The changeable face plate version
is supplied with mylar sheets which
enable you to choose a different
design or orientation (horizontal or
vertical).
Face Plate Installation
Vertical Placement
The face of the front panel may be
changed to reflect a different design
or orientation. Remove the clear
plastic cover and replace the
underlying mylar sheet with
another of your choice, (see
If your desktop space is limited you
may choose to place the Decoder
Amplifier vertically, (see Diagram M).
Place the Decoder Amplifier on a
hard, flat surface.
There are ventilation slots on the
Decoder Amplifier’s enclosure. Do not
block these ventilation slots by
placing materials over them.
K
Diagram K). Replace the cover.
L
M
Stand
Mylar Sheet
Front Panel
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Decoder Amplifier Functions
The Standby LED lights up when the
Power Adapter is connected to the
mains. Press the Power button to turn
on the Decoder Amplifier.
The CMSS Music LED will remain
illuminated after initial start-up. The
last used CMSS mode’s light will
illuminate for subsequent start-ups
from system standby mode.
The Optical LED also lights up after
initial start-up. The last used Dolby
Digital/PCM Audio input’s light will
illuminate for subsequent start-ups
from system standby mode.
The Digital DIN or Line In LED
lights up, depending on whether
Digital DIN or Analog Line In is
connected. The Digital DIN LED will
blink if a PC connected to the Decoder
Amplifier is off but a Digital DIN
input is connected. Turning on your
PC stops the LED’s blinking.
Digital DIN (Dolby Digital/PCM Audio)
inputs.
1. POWER
:
Sets the system to “On”
or standby. When set to “On”, the
Standby LED above the power
button turns off.
1
4
10
11
2. SUBWOOFER, CENTER AND
SURROUND These controls
:
adjust the level of the indicated
channels. Their output level
should be balanced with the fixed
output level of the Left and Right
front Satellites.
12
5
6
2
3. MASTER Adjusts the volume of
:
the entire system. The Master
volume knob is servo controlled
via the Remote Control.
7
8
9
4. CMSS CMSS (Creative Multi
:
10
3
Speaker Surround) processes
analog program material.
Repeated presses of this button
step through four different
operation modes.
MOVIE: Creates a 5.1 speaker
soundfield appropriate for movie
or game enjoyment from an
analog sound source.
The indicator light for Dolby Digital
will illuminate automatically if a
Dolby Digital program is playing.
That is, when a Dolby Digital signal
passes through the Decoder’s
Legend
Button
LED
processor via the Optical,Coaxial or
Download from Www.Somanuals.com. All Manuals Search And Download.
13
MUSIC: Creates a 5.1 speaker
soundfield appropriate for music
from any analog sound source.
FOURPOINT/5.1 DIN: Use this
mode for DVD games having
Dolby Digital soundtracks with
EAX or Microsoft DirectSound3D
for real-time positioning of sound
effects. Typically a Dolby Digital
5.1-channel + analog signal
source.
If a signal source is connected
to the Analog Line In minijacks,
4.1-channel output is produced.
If the signal source is
connected to the Digital DIN
input, up to 5.1-channel output is
produced. Typically when using a
Sound Blaster Live! 5.1 sound
card or the DIN bracket bundled
with Live! Drive IR. For more
details, see “Signal Source
Connection Diagram” on page 6.
The DIN LED blinks if no signal
or an invalid audio signal like an
AC-3 signal is detected. In the
case of an AC-3 signal, select
Digital DIN at the Dolby Digital/
PCM Audio input selection.
STEREO: Use this mode when
you want to hear just stereo
effects or the stereo Dolby Digital
downmix of a DVD. The Dolby
Surround Pro Logic processor is
disabled in this mode.
RR-Right channel program is
directed to both Left and Right
front speakers. See “Audio Mode
Selection” on page 16 for further
information about this feature.
11. TEST Press this button to start
:
the “test sound” generator. Use
this test sound to position all the
speakers and to balance their
relative output.
5. DOLBY DIGITAL /PCM AUDIO:
Use this button to select the
signal source input. Repeated
presses of the button cycles
between Optical, Coaxial, Digital
DIN and Off.
6. MULTI-CHANNEL: Use this
button to select the signal source
input. Repeated presses of the
button cycle between Line In,
Digital DIN and Off.
The test sound moves in
8. DOLBY PRO LOGIC This
:
sequence from the left Satellite,
the Center Speaker, the right
Satellite, then to the rear right
Satellite, rear left Satellite and
the subwoofer. All indicator lights
will blink on and off while the
test sound generator is in
operation.
The test sound will operate for
three complete cycles and then
stop. You can terminate the
sound at any point by pressing
the Test button again.
button cycles from Dolby Pro
Logic processing of the digital
input to Dolby Pro Logic
processing of the analog input,
:
7. AUDIO MODE Use this button
:
to play just the left or right
channels of a stereo digital signal
(PCM from an audio CD, a Video
CD or a stereo signal from a DVD).
Use this when, for example, a
Video CD has different languages
on the left and right channels.
Repeated presses of the button
select which channel is fed to
both the Left and Right front
speakers.
:
First use the test sound to
verify that each speaker is
operating.
operable except speaker test.
Press a second time to restore
audio output. After being muted
for more than thirty minutes, the
Decoder Amplifier goes to
Then make sure the speakers
are positioned so that the test
sound can be clearly heard.
Finally, adjust the front panel
level controls for the Center,
Subwoofer and rear Satellites.
Adjust each control so its speaker
achieves a balanced output level
with the left and right satellites
LL-Left channel program is
directed to both Left and Right
front speakers.
standby mode and the Standby
LED lights up.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
(which provide a fixed “reference”
output level).
(This function is only available
on the Remote Control)
Surround Reference
All functions except for the
level controls are disabled while
the test sound is running.
The speaker level controls
operate at all times. If desired,
you may adjust these controls
during program material to fine-
tune the balance.
(This function is only available
on the Remote Control)
Note: Volume levels during the
test sequence are lower than
during normal operation.
the sound will be properly reproduced
Dolby Digital
by the DTT3500 Digital
.
Dolby Digital (earlier called AC-3)
delivers five discreet full-range
channels (left front, center, right
front, left surround and right
surround) plus a separate Low
Frequency Effects (LFE) channel.
Many soundtracks on the latest
generation laser discs, DVDs and
High Definition Television (HDTV),
are encoded with Dolby Digital
technology.
When a 5.1-channel Dolby Digital
program source is playing, such as
from a Creative PC-DVD player, DVD
player or game console, the Dolby
Digital indicator light will illuminate
automatically.
Note: Not every section of a DVD
will be 5.1-channel encoded. On
many DVDs, only the main movie
program will be available in 5.1-
channel sound. Other supporting
chapters (like a “Director’s Comment”
section) may be in stereo or mono.
These sections will not light the
Dolby Digital indicator even though
Dolby Pro Logic
Dolby Surround is an earlier surround
sound standard which is decoded
with a Pro Logic processor in the
DTT3500 Digital. The Pro Logic
steering circuitry derives separate
center and rear channels from
encoded stereo program sources.
Pro Logic processing provides a
convincing movie soundfield when
the material is specifically encoded
for Dolby Surround. Most older stereo
movie soundtracks will only be
encoded for Dolby Surround, even
though the program source may be a
DVD’s digital output. Most DVDs
containing Dolby Surround program
material will cause both the Dolby
Digital and Dolby Pro Logic lights to
illuminate. DTT3500 Digital will
decode these digitally transferred
Dolby Surround programs through
the digital Pro Logic decoder
12. DYNAMIC MODE: Press this
button to experience the full
dynamic range of Dolby Digital
programs. The LEDs on the upper
half of the Decoder Amplifier
light up momentarily. The
program source will sound louder
in Dynamic Mode. If you press
this button again, the default
mode (compressed) resumes. The
LEDs on the lower half of the
Decoder Amplifier light up
momentarily.
automatically.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
CD-ROMs and CDs with Dolby
Surround encoding will feature the
Dolby Surround logo at the beginning
of the program or on the packaging.
Process these programs by selecting
Analog In using the Dolby Pro Logic
button for input through Analog Line
In.
If using Digital DIN input, ensure
that the Digital DIN on the Dolby
Digital/PCM Audio input is selected.
Then select Digital In using the Dolby
Prologic button.
When Dolby Pro Logic is selected
CMSS is turned off. To turn on CMSS
again, turn off Dolby Pro Logic first.
Do not select a Pro Logic decoding
mode if the program material is not
encoded for Dolby Surround.
Excessive center channel output will
result, and most of the stereo effect
will be lost. Use CMSS “Movie” or
“Music” modes to upmix stereo
programs to a realistic 5.1-channel
sound field.
aspects to a Dolby Surround Pro Logic
processor.
The Music mode creates a
sequences may be in the WAV format.
CMSS Movie mode supports 5.1-
channel output for .WAV, .AVI, .MIDI
and other audio software formats.
Few, if any of these kinds of formats
are Dolby Surround encoded.
The FourPoint/5.1 DIN mode passes
the four discreet channel audio of 4-
channel games direct to each satellite
channel. It does not synthesize rear
channel output, so stereo signal in
this mode will play just through the
front two speakers and subwoofer.
The STEREO mode plays the Left
and Right Front speakers and the
subwoofer. It also lets you hear the
stereo downmix from any DVD.
The Dolby Pro Logic processor is
disabled in this mode.
contain dual-language soundtracks.
DTT3500 Digital lets you select one
of these languages and play it
through both the Left and Right
speakers.
If there is no indication of which
channel is which, and you hear two
different language soundtracks
during stereo playback, select the
“LL” and “RR” settings until you find
the language soundtrack you want.
The Audio Mode selection feature
can only be used with the PCM digital
soundtrack of a Video CD or DVD with
a dual soundtrack, not a DVD
encoded with Dolby Digital 5.1 sound
or Dolby Surround-encoded material.
If you have an analog program with
separate left and right channels (the
analog output of a CD ROM, or the
analog stereo output of a “software”
Video CD, for instance), you will have
to use the balance control in your
PC’s audio software to mute the
undesired channel.
convincing 5.1-channel surround
soundfield with typical stereo
sources, whether they are Dolby
Surround-encoded or not. It works
well with Dolby Pro Logic, WAVE, AVI
and MIDI program material. In
essence, CMSS Music mode puts you
“on the stage” for the music’s
performance, surrounding you with
the performers.
In a similar manner, Movie mode
provides the sonic impression of
being front and center at a movie
screening. Dialog and all normally
centered sounds from a stereo
program are heard through the center
speaker. Use this mode whenever a
music program has sounds you want
to blend with on-screen action or
dialog.
Audio Mode Selection
The stereo soundtracks of some
movies on Video CDs (VCD format)
contain different languages. For
example, a 2-channel soundtrack may
contain Mandarin on the right
Unlike Pro Logic decoding, CMSS
Music, Movie and FourPoint/5.1 DIN
modes are appropriate for use with
multi-coded sources such as DVD
games. In some game titles, the
movie sequences may be encoded in
Dolby Surround but the game
Creative Multi Speaker
channel and English on the left
channel. The VCD program literature
should indicate the presence of dual-
language soundtracks. Similarly,
some movies in the DVD format will
Surround (CMSS)
CMSS is a 2-channel to 5.1-channel
sound processor similar in some
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Multiple Connections
Monitor
The DTT3500 Digital system has many
configuration possibilities. Typically,
the system can be connected to either a
game console or a PC.
2. Connect your video converter’s
output to a VGA switch box.
3. Connect your PC’s VGA output to
the VGA switch box.
Game Console
However, the DTT3500 Digital
allows you to connect to both,
forming a hybrid system.
4. Connect the PC monitor’s VGA
input socket to the output of the
VGA switch box.
PC
After completing the above
connections you will be able to
choose the display output between
your PC and game console by using
the switch box.
To select the audio output, use the
Dolby Digital/PCM Audio or Multi-
channel input buttons on the Decoder
Amplifier.
Connecting to a Game Console and
a PC
RF to VGA
converter box
Video Signal
You can connect your game console
and PC to the DTT3500 Digital
system while sharing one monitor by
following the instructions below.
Audio Connection:
1. Connect your game console’s
audio output to the Decoder
Amplifier’s Front minijack input
with the provided Dual Female-
to-Female RCA adapter.
VGA switch box
Audio Signal
DTT3500 Digital
2. Connect your PC’s audio output to
the Decoder Amplifier.
Video Connection:
1. Connect your game console’s
video output to a RF to VGA video
converter box.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Applications Guide
For 2-channel sound cards:
experience from Microsoft
DirectSound3D or Creative EAX
titles.
Playing Games:
Playing DVD Movies
1. Select LINE IN input using the
MULTI-CHANNEL button.
2. Select MOVIE or MUSIC mode
using the CMSS button.
Playing Multi-format DVD Games
These games have Dolby Digital or
Dolby Pro Logic movie clips mixed
with the actual game sequence. These
DVD games have a mix of Dolby
Digital 5.1 sound (a digital signal at
the SPDIF input) and soundcard
wavetable output (a signal at the
analog input).
Using PC-DVD player on a PC
Select the COAXIAL input using the
DOLBY DIGITAL/PCM AUDIO input
selection button.
3. For Sound Blaster Live! users,
enable the multi-channel
configuration on your PC.
Software DVD Player
Listening to PC-DVD movies with
5.1-channel Dolby Digital sound
Be sure to listen only to the digital
program source. You can do this by:
1. Making sure your PC-DVD
player’s stereo downmix is not
sent to your soundcard. For
example, disconnect any cable
link between the cards, or
2. Muting the CD input of your
computer’s software mixer/
Playing Conventional Games
Select MUSIC or MOVIE by pressing
the CMSS button until the LED for
MUSIC or MOVIE mode lights up.
For sound card’s with analog output
to FRONT and REAR ANALOG LINE IN
or digital output to DIGITAL DIN:
Use the software DVD player to
process all signals into multi-channel
output.
1. Select LINE IN or DIGITAL DIN
using the MULTI-CHANNEL
button.
PC-DVD Setup
Playing Console Games
1. Select LINE IN input using the
MULTI-CHANNEL button and/or
OPTICAL input using the DOLBY
DIGITAL/PCM AUDIO button.
2. Select MUSIC or MOVIE by
pressing the CMSS button until
the LED for MUSIC or MOVIE
mode lights up.
For AC-3 signal source connected to
COAXIAL input:
Select the COAXIAL input using the
DOLBY DIGITAL/PCM AUDIO input
selection button. The Dolby Digital or
Dolby Pro Logic source signal will be
automatically processed.
For multi-channel inputs (FRONT and
REAR ANALOG LINE IN or DIGITAL
DIN):
2. Select FOURPOINT/5.1 DIN mode
using the CMSS button.
volume control application.
Playing Microsoft DirectSound3D or
EAX Games
1. Select LINE IN or DIGITAL DIN
input using the MULTI-CHANNEL
button.
2. Under CMSS on your DTT3500
Digital decoder amplifier, select
FOURPOINT/5.1 DIN to fully
enjoy up to 5.1-channel gaming
Using software DVD player on a PC
1. Set the software DVD player to
pass through AC-3 to DIGITAL
DIN output.
2. Select DIGITAL DIN using the
DOLBY DIGITAL/PCM AUDIO
input selection button.
1. Select LINE IN or DIGITAL DIN
input using the MULTI-CHANNEL
button.
2. Select the FOURPOINT/5.1 DIN
mode using the CMSS button.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Using set-top DVD player or
PlayStation2
Select OPTICAL or COAXIAL using the
DOLBY DIGITAL/PCM AUDIO input
selection button.
Using set-top VCD player
1. Select LINE IN input using the
MULTI-CHANNEL button.
For source connected to ANALOG
LINE IN:
Playing VCD Movies
Using PC-DVD player on PC
Select the COAXIAL input using the
DOLBY DIGITAL/PCM AUDIO input
selection button.
1. Select LINE IN input using the
MULTI-CHANNEL button.
2. Select ANALOG IN using the
DOLBY PRO LOGIC button.
2. Select the Movie mode by
pressing the CMSS button until
the LED for Movie mode lights
up. You can experience surround
sound instead of mono/stereo
sound; all dialog and central
sounds will be heard through the
center speaker, while music and
off-stage sounds are heard
For movies with Dolby Digital (AC-
3) soundtracks
This signal is detected automatically
and the DOLBY DIGITAL LED lights
up. You will experience Dolby Digital
5.1-channel output.
Using SoftMPEG player or
PlayCenter on PC
1. Select LINE IN or DIGITAL DIN
input using the MULTI-CHANNEL
button.
2. Select the Movie mode by
pressing the CMSS button until
the LED for Movie mode lights
up.
This mode lets you experience the
surround sound with 5.1-channel
output; all dialog and central
sounds will be heard through the
center speaker, while music and
off-stage sounds are heard
through the other four satellites.
3. If you are using PlayCenter to
play the VCDs, disable all CMSS
effects in your PlayCenter - use
only DTT3500 Digital’s Movie
mode.
For 2-channel movies which are Dolby
Surround-encoded carried within the
Dolby Digital compressed bitstream
through the other four satellites.
For VCD movies with Dolby
Surround-encoded stereo program
Use the Dolby Pro Logic decoder for
5.1-channel movie viewing
experience.
The Dolby Pro Logic decoder will
automatically decode the program for
5.1-channel movie experience.
For 2-channel DVD movies which are
Dolby Surround-encoded
For source connected to OPTICAL/
COAXIAL/DIGITAL DIN:
The Dolby Pro Logic decoder will
automatically decode the program for
5.1-channel movie experience.
1. Select OPTCAL/COAXIAL/DIGITAL
DIN input using the DOLBY
DIGITAL/PCM AUDIO button.
2. Press the DOLBY PRO LOGIC
button until the DIGITAL IN LED
lights up.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Singing Karaoke on PC with Sound
Blaster Live! and Creative PC-DVD
Decoder Card (with Creative
Navigator application)
1. Ensure your microphone is
connected to the MIC IN minijack
of Sound Blaster Live!.
2. Enable the Microphone source in
the Mixer.
3. Select one of the seven Karaoke
modes under Environment in
Creative Launcher.
4. Select the COAXIAL input using
the DOLBY DIGITAL/PCM AUDIO
input selection button.
5. Press the AUDIO MODE button of
the DTT3500 Digital decoder
amplifier unit until you hear only
the music i.e. vocal portion is
masked out.
CD Audio Music
Karaoke Music
Singing Karaoke on PC with Sound
Blaster Live! only (with Creative
PlayCenter)
1. Select LINE IN or DIGITAL DIN
input using the MULTI-CHANNEL
button.
2. Ensure your microphone is
connected to the MIC IN of Sound
Blaster Live!.
3. Enable the Microphone source in
the Mixer.
4. Select one of the seven Karaoke
modes under Environment in
Creative Launcher.
5. Click the Audio Menu button on
the Creative PlayCenter to hear
only the music, i.e. with the vocal
portion masked out.
Enjoying CD Audio on PC
1. Select LINE IN or DIGITAL DIN
input using the MULTI-CHANNEL
button.
2. Select the Music mode by
pressing the CMSS button until
the LED for Music mode lights up.
This mode creates an enveloping
five-speaker surround effect that
enhances stereo music.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Important!
Specifications
EAX
EAX is a collection of powerful,
innovative audio technologies.
Developed by Creative's world-class
audio scientists and built into
groundbreaking Personal Digital
Entertainment (PDE) solutions, EAX
is changing the way you experience
audio.
Sony's PlayStation2™, direct digital
interfacing via the optical connector
is possible, assuring the best possible
DVD audio experience.
DTT3500 Digital
Playback Levels
DTT3500 Digital is intended for
individual or small group listening
and can achieve surprisingly high
output levels. However, playing
heavy-bass program material
continuously at overly loud, distorted
levels may blow the system’s internal
fuse.
The fuse can be replaced only by a
qualified representative. To avoid this
inconvenience and a possible non-
warranty repair charge, reduce the
playback volume when the system
shows obvious signs of stress, for
example, when it sounds raspy, fuzzy,
and/or muddy.
6-Channel Amplifier
Satellite speaker:
7 watts RMS per channel
Different audio content from games
to movies to music files can be
further enhanced with the advanced
EAX technologies incorporated into
the DTT3500 Digital. "Movie" mode
expands the soundfield across the full
5.1 speaker configuration - great for
enhancing playback of regular stereo
audio soundtracks. In addition, the
"Music" mode provides special
Center Channer amplifier:
21 watts RMS per channel
EAX offers advanced, interactive
audio and high-definition sound to a
new generation of portable audio
appliances, audio applications, and
internet services. Advanced
technologies for incredible, cutting
edge audio are built into powerful
tools. EAX-enabled products let you
shape and customize your audio
experience, and include advanced
audio features for music composition
and sound design.
Subwoofer amplifier:
23 watts RMS per channel
processing to enhance playback of
audio CDs and music files.
These specifications apply to
DTT3500 Digital operating from the
supplied 15V 4A DC power adapter.
The DTT3500 Digital is the most
complete 5.1 speaker system for
movies and games. The built-in Dolby
Digital decoder and 24-bit Digital-to-
Analog Converter (DAC) delivers a
thrilling, high quality home theater
audio experience. When used with
Download from Www.Somanuals.com. All Manuals Search And Download.
21
1-Year Limited Warranty
Technical Support
o the original purchaser,
This is the sole and expressed
Inside U.S.A., Canada and
Inside Asia
Creative Technology Ltd.
Technical Support
31 International Business Park
Creative Resource
Singapore 609921
Tel: 65–895–4100
Fax: 65–569–6640
Operating hours (Singapore Time):
Cambridge SoundWorks, Inc.
will warrant the speaker system
to be free of defects in material and
workmanship for a period of
one (1) year from date of purchase.
With respect to defects, Cambridge
SoundWorks will, at its option,
replace the product or repair the
defect in the product with no charge
to the original purchaser for parts or
labor.
warranty. This warranty is in lieu of all
other warranties, expressed or implied,
of merchantability, fitness for purpose
or otherwise. In no event shall
Cambridge SoundWorks be liable for
incidental or consequential damages or
have any liability with respect to
defects other than the obligations set
forth above.
To ensure warranty coverage, it is
incumbent upon the original purchaser
to contact the retailer where the
DTT3500 Digital was purchased and
inform them of the defect within the
warranty period. The only acceptable
method of establishing warranty status
is a copy of the original proof of
purchase indicating customer’s name
and purchase date.
Latin America
Creative Labs Inc.
Technical Support
1523 Cimarron Plaza
Stillwater, OK 74075
Tel: 1–405–742–6622
Fax 1–405–742–6633
Operating hours (Central Time):
T
Mon–Fri 9:00
A
.
M.–6:00
P.M.
Daily 8:00
A.M.–12 Midnight
Sat–Sun & Public Holidays closed
This warranty does not extend to any
defect, malfunction or failure caused by
misuse, abuse, accident, faulty hookup,
defective associated equipment or use
of the speaker with equipment for
which it is not intended.
To reach Technical Support via the
Internet, visit our web site at
You can reach Customer Service by
To reach Technical Support via the
Internet, visit our web site at
support
phone at 1–800–998–1000
,
Mon–Fri 8:00
A
.
M.–7:00
P.M. (Central
This warranty is valid only when the
speaker is returned to the retailer where
the DTT3500 Digital was purchased.
Time).
You can also use our Faxback
service at 1–405–372–5227
.
© 2000 Cambridge SoundWorks, Inc. All rights reserved. Cambridge SoundWorks is a registered trademark, and DeskTop Theater is a trademark of Cambridge SoundWorks, Inc., Newton, MA. The Creative logo, Sound
Blaster and the Sound Blaster logo are registered trademarks and EAX, the EAX logo, PC-DVD, CMSS, Live!, and Creative Multi Speaker Surround are trademarks of Creative Technology Ltd. in the United States and/or
other countiries. NOMAD is a registered trademark of Aonix and is used by Creative Technology Ltd., and/or its affiliates under license. The DeskTop Theater 5.1 DTT3500 Digital’s Dolby Digital decoder/amplifier is
manufactured under license from Dolby Laboratories. ‘Dolby’, ‘Dolby Digital’, ‘Pro Logic’, ‘AC-3’ and the double-D symbol are trademarks of Dolby Laboratories, Inc. Confidential unpublished works. Copyright 1992-1997
Dolby Laboratories. All rights reserved. Sony is a registered trademark and PlayStation2 is a trademark of Sony Computer Entertainment Inc. Microsoft and DirectSound are registered trademarks of Microsoft Inc. All
other brands and product names are trademarks or registered trademarks of their respective holders. All specifications are subject to change without prior notice. Actual contents may differ slightly from those pictured.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
|