FXT15
FXT15
Guitar Amplifier with
Digital Signal Processing
User’s Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
FXT15Guitar Amp with Digital Signal Processing
The Front Panel:
1
2
3
4
5
6
7
8
9
10
11
12
1: INPUT: Use this jack to connect your guitar to
the amplifier by means of a shielded instrument
cable.
11: SPEAKER: Use this jack to connect the
amplifier to an external speaker. The internal
speaker is disconnected when this jack is used.
The impedance of the external speaker must be 4
ohms or greater.
SOLO CHANNEL: A high gain channel giving you
sounds from a slight edge to serious overdrive.
WARNING: Do not attempt to use headphones in
the Speaker jack! Permanent hearing damage
could result!
2: GAIN: Use this control to adjust the amount of
distortion for the Solo channel.
3: LEVEL: Use this control to adjust the output
level of the Solo channel.
12: POWER: Use this switch to turn the amplifier
on (top of the switch depressed) and off (bottom of
the switch depressed). The switch illuminates
when the amplifier is turned on.
4: SOLO/CLEAN: Use this switch to select the
Solo or Clean channel. With the switch in the out
position, the Clean channel is selected. When the
switch is depressed, the Solo channel is selected.
The Rear Panel:
13: POWER CORD: The grounded power cord
should only be plugged into a grounded power out-
let that meets all applicable electrical codes and is
compatible with the voltage, power, and frequency
requirements stated on the rear panel. Do not
attempt to defeat the safety ground connection.
CLEAN CHANNEL: A normal gain channel
designed to give you crystal clear sounds to medi-
um distortion.
5: VOL: Use this control to adjust the output level
of the Clean channel.
6: LOW: Use this control to adjust the low fre-
quency level of the amplifier.
DSP: THE DIGITAL EFFECTS
7: MID: Use this control to adjust the midrange fre-
quency level of the amplifier.
REV 1
REV 2
REV 3
REV 4
DLY 1
small room reverb
medium room reverb
small hall reverb
large hall reverb
8: HIGH: Use this control to adjust the high fre-
quency level of the amplifier.
9. DSP: Use this control to select one of the 16
built-in digital effects. The effects are described in
the table to the right.
short delay
DLY 2
medium delay
DLY 3
long delay
FLNG 1
FLNG 2
CHO 1
CHO 2
RTRY
slow shallow flange
fast deep flange
10: HEADPHONES: Use this jack to connect
headphones to the amplifier. The internal speaker
is disconnected when headphones are used.
slow shallow chorus
fast deep chorus
medium-speed rotating speaker
touch-sensitive wah-wah
inverse wah-wah
CAUTION: To avoid possible damage to your hear-
ing, do not use headphones for extended periods
of time at extremely loud levels.
T-WAH
I-WAH
DOUBLER simulates second track out-of-sync
Download from Www.Somanuals.com. All Manuals Search And Download.
FXT15Guitar Amp with Digital Signal Processing
FXT15 TECHNICAL SPECIFICATIONS:
Output Power Rating
Gain
12W RMS @ 5% THD, 4Ω, 120 VAC
Solo Ch
86dB +/-6dB @ 1kHz
46dB +/-6dB @ 1kHz
Clean Ch
Maximum Input Signal Accepted
Tone Controls
2.2 volts RMS min. @ 400Hz
Low
Mid
25dB range @ 80Hz
19dB range @ 900Hz
23dB range @ 5kHz
High
Signal To Noise Ratio
Solo Ch
>50dB
>65dB
Clean Ch
Speaker Size and Rating
Power Requirements
8” Crate Custom Design 4 ohm
120 VAC, 60Hz, 30VA
100/115VAC, 50/60Hz, 30VA
230VAC, 50/60Hz, 30VA
Size and Weight
13” H x 13-5/8” W x 8-1/4” D, 15 lbs.
The FXT15 is covered with a durable Tolex material: wipe it clean with a lint-free cloth.
Never spray cleaning agents onto the cabinet. Avoid abrasive cleansers which would damage the finish.
Crate continually develops new products, as well as improves existing ones. For this reason, the specifications
and information in this manual are subject to change without notice.
©2003 SLM Electronics, a division of St. Louis Music, Inc • 1400 Ferguson Avenue • St. Louis, MO 63133
47-447-06 • 030304
Download from Www.Somanuals.com. All Manuals Search And Download.
|