Craftsman Automobile Parts 50182 User Manual

Operators Manual  
JACK STANDS  
Model 950182 - 2-1/4 Ton Capacity per pair  
• Safety  
• Assembly  
• Operation  
BEFORE using this product, read this manual  
and follow all its Safety and Operating  
!
instructions. Failure to do so may result in  
personal injury and/or property damage.  
Sears, Roebuck and Co., Hoffman Estates, IL 60179  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SAFETY INSTRUCTIONS  
!
!
WARNING  
ADVERTENCIA  
• Study, understand, and follow all printed  
materials provided with and on this  
device before use.  
Leer, comprender, y seguir las  
instrucciónes antes de utilizar el aparato.  
• El manual de instrucciónes y la  
información de seguridad deben estar  
comunicado en lengua del operador  
antes del uso.  
Rated capacity is per pair! Do not  
exceed rated capacity.  
• Use as matched pair to support one end  
of a vehicle only. Use only 1 pair per  
vehicle.  
• No seguir estas indicaciónes puede  
causar daños personales o materiales.  
• Use only on hard, level surfaces.  
• Center load on saddle.  
! SAFETY MESSAGE !  
Be sure all tools and personnel are clear  
before lowering load. No alterations shall  
be made to this device. Only attachments  
and/or adapters supplied by the  
manufacturer shall be used. Lift only on  
areas of the vehicle as specified by the  
vehicle manufacturer.  
• Jack stands are not to be used to  
simultaneously support both ends or one  
side of a vehicle.  
• No alteration shall be made to this  
device.  
• Failure to heed these markings may  
result in personal injury and/or property  
damage.  
INSPECTION  
Inspect the Jack Stands before each use.  
Do not use if bent, broken or cracked  
components are noted.  
ASSEMBLY  
CARTON CONTENTS  
RATCHET BAR  
Inside the carton box, you will find:  
1. Two jack stand frames.  
2. Two ratchet bars.  
PAWL (INSIDE,  
NOT SHOWN)  
LOCKING  
HANDLE  
3. Two lock pins.  
BASE  
FRAME  
HOW TO ASSEMBLE JACK STANDS  
(refer to Fig. 1)  
LOCK PIN  
1. Insert the ratchet bar into frame, orient  
the racthet side to the pawl side of  
frame.  
2. Move the ratchet bar to lowest position  
by raising the locking handle and guiding  
the bar downward.  
3. Support the ratchet bar with suitably  
sized wooden block. With hammer and  
punch or other suitable tool, drive the  
lock pin into the hole at the bottom of  
the ratchet bar to prevent overextension  
and loss of the bar.  
FIG. 1  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
4. Always use jack stands as a pair and  
BEFORE USE  
only on those parts of a vehicle which  
can be fully captured between the outer  
lugs of each stand’s saddle.  
1. Inspect stands before each use. Do not  
use if bent, broken or cracked  
components are noted. Ensure that all  
parts move freely.  
Rated capacity of jack stands is per  
!
pair, it is NOT the sum of individual  
capacities unless specifically noted to  
the contrary by the jack stand  
manufacturer. Do Not exceed rated  
capacity. Ensure that the vehicle  
support points are fully captured  
between the outer lugs of both jack  
stands. Use a matched pair of jack  
stands per vehicle to support 1 end  
only. Use 1 pair per vehicle only.  
Failure to do so may result in sudden  
loss of load, which may cause personal  
injury and/or property damage.  
2. Before using this product, read the  
owner’s manual and familiarize yourself  
thoroughly with the product and the  
hazards associated with its improper  
use.  
KNOW YOUR JACK STANDS  
SADDLE  
RATCHET  
BAR  
LOCKING  
HANDLE  
5. Slowly and carefully lower the load  
completely onto the stands, ensure that  
the load is centered and captured as  
described in Step 4.  
6. Check to ensure that load is secure on  
stands before working under vehicle.  
JACK STAND  
FRAME  
FIG. 2  
HOW TO USE YOUR JACK STANDS  
TO SUPPORT A VEHICLE  
1. Raise the vehicle or load with an  
automotive jack.  
TO REMOVE AND STORE JACK  
STANDS  
2. Adjust jack stand height by pulling up  
on ratchet bar. The weight of the locking  
handle should lock the ratchet bar into  
a secure position. To verify this, simply  
push down on the locking handle to  
ensure that the ratchet bar is secured.  
1. Raise vehicle clear of stands with  
suitable jack.  
2. Raise the locking handle to allow ratchet  
bar to glide down to lowest position.  
3. Carefully remove stands.  
4. Carefully lower vehicle with jack.  
5. Ensure that all tools, equipment and  
personnel are clear before lowering  
load.  
3. Carefully position the stands beneath  
the load so that when load is lowered it  
will contact the center of the jack stand  
saddles.  
SPECIFICATIONS  
CAPACITY  
PER PAIR  
MODEL  
MIN. HEIGHT MAX. HEIGHT BASE DIMENSION NET WEIGHT(2 pcs.)  
10-5/8 in.  
(270mm)  
17-1/8 in.  
(435mm)  
50182 2-1/4 TON  
7-1/2 X 6-3/4 in.  
11.4 LBS (APPROX.)  
MAINTENANCE  
STORAGE  
INSPECTION  
Store stands in upright position and in a  
clean, dry area.  
Periodically inspect each stand. Ensure all  
parts move freely. Do not apply oil or  
grease to any portion of this product. If rust  
appears, sand affected area and cover with  
suitable utility paint. Please note that there  
are no replacement parts applicable to this  
device.  
For after sale support and assistance:  
Call 8:00 AM - 4:45 PM CST., Monday - Friday 1-888-332-6419  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Get it fixed, at your home or ours!  
Your Home  
For repair – in your home – of all major brand appliances,  
lawn and garden equipment, or heating and cooling systems,  
no matter who made it, no matter who sold it!  
For the replacement parts, accessories and  
owner’s manuals that you need to do-it-yourself.  
For Sears professional installation of home appliances  
and items like garage door openers and water heaters.  
1-800-4-MY-HOME®  
Call anytime, day or night  
(1-800-469-4663)  
(U.S.A. and Canada)  
Our Home  
For repair of carry-in items like vacuums, lawn equipment,  
and electronics, call or go on-line for the location of your nearest  
Sears Parts and Repair Center.  
1-800-488-1222 Call anytime, day or night (U.S.A. only)  
To purchase a protection agreement (U.S.A.)  
or maintenance agreement (Canada) on a product serviced by Sears:  
1-800-827-6665 (U.S.A.)  
1-800-361-6665 (Canada)  
Para pedir servicio de reparación  
a domicilio, y para ordenar piezas:  
Au Canada pour service en français:  
1-800-LE-FOYERMC  
1-888-SU-HOGAR®  
(1-888-784-6427)  
(1-800-533-6937)  
© Sears Brands, LLC  
®
Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC  
Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC  
®
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Craftsman Garage Door Opener 13953682 User Manual
Craftsman Lawn Mower Accessory 358792440 User Manual
Curtis Clock Radio CR1274UK User Manual
CyberResearch Switch GFC 1716A User Manual
EarthQuake Chipper 1692210 User Manual
Electro Voice Musical Instrument Amplifier GS 2000A User Manual
Electro Voice Speaker EVX 156 User Manual
Extron electronic Stereo Receiver HDMI 201 Tx Rx User Manual
Frigidaire Air Conditioner FRA123CT1 User Manual
Global Machinery Company Nail Gun ACALN User Manual