INSTALLATION INSTRUCTIONS
V90229-1T
COMBOLIGHT
R
TRIMMED
Avoid Fire or Electric Shock
Page 1 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
FIXTURE MOUNTING:
1. Fixture must be mounted using either BUTTERFLY MOUNTING
BRACKETS or HANGER BARS (Contact RSA Dealer for HANGER BARS).
INSTALLATION NOTE:
DO NOT install insulation within 3in of any part of the Luminaire.
Blinking light of this thermally protected Luminaire may indicate overheating.
BUTTERFLY MOUNTING:
2. Fixture comes equipped with universal BUTTERFLY MOUNTING
BRACKETS that can take common 1" or 1-1/2" black iron or galvanized
MOUNTING CHANNELS (supplied by others). See Fig 1.
SCREW
JBOX COVER
JBOX
3. Position fixture so the MOUNTING CHANNELS lie on top of the ceiling
runners.
Figure 2
4. Fasten MOUNTING CHANNELS securely to ceiling runners.
9. A clean, square hole in the CEILING MATERIAL must be cut. Install the
ceiling material below housing as seen in Fig 4.
5. Secure MOUNTING CHANNELS to universal BUTTERFLY MOUNTING
BRACKETS with wire tie downs.
10. Replace the TRIM into the HOUSING by connecting the TORSION
SPRINGS to the HOUSING. Push the TRIM into the HOUSING until flush
with the CEILING MATERIAL as seen in Fig 4.
6. The BUTTERFLY MOUNTING BRACKETS are height-adjustable and
should be set so that the APERTURE COLLAR will be flush with the
finished ceiling plane.
HOUSING
MOUNTING
CHANNEL
TORSION
SPRING
BUTTERFLY
MOUNTING
BRACKETS
TRIM
Figure 3
HEX
SCREW
Figure 1
ELECTRICAL:
7. Remove the JBOX COVER from the JBOX by removing the four SCREWS.
Connect supply lead wires to junction box lead wires in accordance with
your local electrical code(s) or N.E.C. Replace JBOX COVER onto JBOX,
securing with SCREWS. See Fig 2.
CEILING MATERIAL INSTALLATION:
HOUSING
8. Pull the TRIM away from the HOUSING. The TORSION SPRINGS will hold
the TRIM onto the HOUSING. Compress the TORSION SPRINGS on each
end of the TRIM, releasing the TRIM from the HOUSING. See Fig 3.
TRIM
CEILING
MATERIAL
Figure 4
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
V90229-3
COMBOLIGHT
R
LAMPHOLDER
Avoid Fire or Electric Shock
Page 3 of 3
THIS PRODUCT MUST BE INSTALLED IN
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND
OPERATION OF THE PRODUCT AND THE
HAZARDS INVOLVED.
*Installation Instructions for qualified electricians only.
*Install per National Electrical Code and local regulations.
*Read Installation Instructions completely before installation.
*Failure to follow Installation Instructions may void warranties.
19. To replace the COVER RING:
Push the COVER RING onto the BACK RING by lining up the
BAYONET SLOTS (see Fig. 11) with the two (2) PINs in the BACK RING.
GIMBAL BRACKET
(Standard Position)
PIN
BACK RING
BAYONET
SLOTS
GIMBAL BRACKET
(Rotated 180° to
"Down" Position)
COVER
RING
Figure 9
Figure 11
17. Once removed, flip the two (2) GIMBAL BRACKETs around (180°) and
tighten the joint if necessary. See Fig. 9.
If necessary, please see Step 21 for gimbal tightening instructions.
20. Once lined up, push straight back until the COVER RING stops, then
while keeping the COVER RING pushed back, turn clockwise until it
pushes forward again slightly. See Fig. 12.
18. Reinsert the lamp ring assembly by turning it counter-clockwise into the
SLOTs on the GIMBAL BLOCKs. Re-tighten the two (2) SET SCREWs
in the GIMBAL BLOCKs. The lamp ring assy should now be oriented in
the "up position". See Fig. 10.
GIMBAL RING
GIMBAL
BLOCK
SNOOT
COVER RING
(AS INSTALLED)
Figure 12
21. Gimbal tightening instructions:
The lamp ring is intended to give positive tension at the PIVOT JOINTS
so the lamp ring can be aimed by hand and held in place by tension.
*If a stronger, more secure lock is required then the PIVOT JOINTS (hex
screws) may be tightened clockwise with a hex wrench tool. See Fig. 6.
*Please note that in some conditions the COVER RING will need to be
removed to gain access to the inner PIVOT JOINTS.
SLOT
SET SCREW
Figure 10
Download from Www.Somanuals.com. All Manuals Search And Download.
|