®
WEATHERMASTER 4 SCREENED TENT
MODEL 2000001595
6. Rotate all eight Leg Poles upright and insert
Before you begin
pin on each web loop at the side locations
as shown. (Fig. 7 & 7A)
Read all instructions before set up.
7A
Pin
• Select a level site clear of rocks, branches, and other hard or sharp
objects, to install your tent.
WARNING: Keep clear of overhead power lines.
• Do not set up your tent under trees because of potential lightning strikes
or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent property
damage or personal injury.
• For best results in windy conditions, position narrow end of tent into
the wind.
• Enlist the help of at least one other person to assist you when it is time
to assemble the tent.
Pole Descriptions
Pole
Pole
Pole
Description
Qty. Dia.
Repair Kit Replacement Kit
Fig. 7
Long Leg Pole, steel
(w/ red marking)
Short Leg Pole, steel
Curved Ridge Pole, steel
(w/ red marking)
Curved Ridge Pole, steel
Awning Pole,
black, fiberglass
4
4
19mm
19mm
N/A
N/A
5010000621
5010000618
7. Locate the plastic hooks at sides and
corners of tent, then snap onto Leg
Poles to attach. (Fig. 8)
2
2
19mm
19mm
N/A
N/A
5010000620
5010000619
1
6.3mm 5010000543 5010000545
Fig. 8
Fig. 9
To Set Up Tent
1. Unfold tent and spread out on a clean, level surface with the
8. To stretch tent to finished size:
• Push in button on Leg Pole while
twisting lower Leg Pole section
counterclockwise (Fig.9);
door facing the desired direction. Unzip doors. (Fig. 1)
Fig. 1
Upper
Leg Pole
Section
• Pull up on top Leg Pole section
until tent is taut;
• Twist the lower Leg Pole clock-
wise until the button locks into
the center or lowest hole;
Button
Door
Center Hole
Lower Hole
Lower
2. Pull four corners of tent taut, then secure
by driving stakes through web loops at an
angle for better anchoring. (Fig. 2)
Leg Pole
Section
• Repeat on remaining Leg Poles.
9. Insert plastic stakes through web
straps located on both sides of tent,
then drive in to secure. (Fig. 10)
Fig. 2
3. Assemble four, steel, shock-corded,
curved Ridge Poles. Insert Ridge Poles
(with red marking) into center sleeves
on top of tent with the red trim (Fig. 3).
Insert the remaining curved Ridge Poles
into the other two sleeves on top of tent.
Fig. 3
NOTE: It may be necessary to remove
metal stakes through web straps at
side of tent and screen room, pull tent
taut, and drive in stakes to secure.
Ridge Poles
with Red
Marking
Sleeves
with Red
Trim
Fig. 10
4. Assemble eight, steel, shock-corded,
Leg Poles. Push down on steel button
on tapered end and insert into end with
four holes.
NOTE: Make sure steel button locks into
third hole on pole as shown. (Fig.4)
5. Insert curved end of
To Attach Rainfly
1. Drape Rainfly over tent. Make sure seams on Rainfly are
facing down and centered over poles of the tent. (Fig. 11)
NOTE: Hook and loop fasteners, located on seams of under-
side of Rainfly, should be centered over Ridge Poles.
2. Assemble thin, black, shock-corded Awning Pole; then insert
through sleeve in Rainfly above door. (Fig. 11)
Button in
third hole
Fig. 4
long Leg Poles (with red
Ridge Poles with
Red Marking
marking) into the ends
of the Ridge Poles (with
red marking). Insert
curved end of remaining
short Leg Poles into the
ends of the remaining
Ridge Poles. (Fig. 5 & 6)
Rainfly
Awning
Pole
Sleeves
with Red
Trim
Curved End of
Long Leg Pole
Sleeve
Fig. 5
Door
Fig. 6
Ridge Poles with
Red Marking in
center 2 sleeves
Fig. 11
(continued on other side)
Download from Www.Somanuals.com. All Manuals Search And Download.
|