Code Alarm Remote Starter CA611 User Manual

CA611 Owners Manual  
CAUTION!  
Be certain that the vehicle is outdoors before using this or any re-  
mote vehicle starting device. A running engine produces dangerous  
carbon monoxide fumes which can be harmful or fatal if prolonged  
exposure occurs. DO NOT remote start the vehicle if the car is  
garaged.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ARMING THE SYSTEM:  
If the passive arming feature has been selected:  
Turn the engine OFF, exit the vehicle, and close all doors, hood and trunk.  
The LED will begin to flash rapidly indicating that the 30 second passive  
arming timer has begun. If the dash mounted LED does not begin to flash  
rapidly, then you have left a door, hood, or trunk ajar. Closing this entry point  
will allow the arming cycle will begin. If any entry point is opened during the  
30 second arming cycle, arming will be suspended. When all entry points are  
closed, the arming cycle will begin again.  
At the end of the 30 seconds, the parking lights will flash once, the siren will  
chirp once, and the LED will begin to flash slowly confirming the system is  
armed. If the siren/horn did not sound when arming, then the chirps have  
been turned off. Refer to the section on "Eliminating the normal Arm/Disarm  
Chirps" found on page 8 of this manual. Passive door locking is a selectable  
feature. If you have the optional door lock/unlock circuit installed, the doors  
may or may not lock passively depending upon the setup during installation.  
PROTECTION WHILE THE SYSTEM IS ARMED:  
Opening any protected entry point, hood, trunk, or doors will cause the alarm  
to trigger immediately. The siren/horn will sound and the parking lights will  
flash for 30 seconds, then stop and continue to monitor all protected entry  
points. If the thief left the door opened, the system will sound for six 30  
second cycles then shut down, isolate the triggered zone and continue to  
protect all other zones.  
Whenever the system is armed, the LED will slowly flash. This serves as a  
visual deterrent to a potential thief. The LED is a very low current light emitting  
diode (L.E.D.), and will not cause the battery to drain even if left unattended for  
long periods of time.  
Whenever the system is triggered, the vehicle's parking lights will flash for the  
full siren/horn sounding period.  
Whenever the system is armed, the vehicle starter circuit is disabled, and the  
vehicle will not start with the ignition key.  
Whenever the system is armed, any strong impact to the vehicle will cause  
the shock sensor to trigger the alarm. Any lesser impact will cause the pre-  
detect stage of the shock sensor to emit a few short series of warning tones  
from the siren/horn.  
Page 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
DISARMING THE SYSTEM:  
As you approach the vehicle, press and release the Disarm button on the  
transmitter. The parking lights will flash 2 times, the siren/horn will chirp 2  
times, and the LED will turn off.  
If you have the optional door lock/unlock circuit installed, the doors will unlock.  
If you have the optional entry illumination circuit installed, the interior light will  
turn on for 30 seconds or until the ignition key is switched on.  
NOTE: If the passive arming mode was selected at time of installation, the  
LED will start flashing rapidly indicating that the system is rearming. Opening  
any door will suspend the automatic arming.  
If the parking lights flashed 3 times, and the siren/horn chirps 4 times, this  
indicates that the alarm system was triggered during your absence. Before  
turning on the ignition key, examine the LED flash pattern. The number of  
flashes identifies the triggered zone. For additional information, refer to  
INTRUSION WARNING SIGNALS (page 5) of this manual.  
If the siren/horn did not sound upon disarm, then the chirps have been turned  
off. Refer to the section titled ELIMINATING THE NORMALARM/DISARM  
CHIRPS (page 8).  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the driver's door only will unlock, pressing the  
unlock button a second time will cause all doors to unlock.  
SILENT DISARMING:  
1. As you approach the vehicle, press and hold the disarm button of your  
transmitter for 2 seconds.  
The parking lights will flash 2 times, and the LED will turn off confirming that  
the system is disarmed. The siren/horn will not chirp. If you have the optional  
door lock/unlock circuit installed, the doors will unlock. If you have the optional  
entry illumination circuit installed, the interior light will turn on for 30 seconds  
or until the ignition key is switched on.  
NOTE: If the passive arming mode was selected at time of installation, the  
LED will start flashing rapidly indicating that the system is rearming. Opening  
any door will suspend the automatic arming. If the parking lights flashed 3  
times, and the siren/horn chirps 4 times, this indicates that the alarm system  
had been triggered in your absence. Before turning on the ignition key,  
examine the LED flash pattern. The number of flashes identifies the triggered  
Page 4  
Download from Www.Somanuals.com. All Manuals Search And Download.  
zone. For additional information, refer to INTRUSION WARNING SIGNALS  
(page 5) of this manual.  
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock  
transmitter button is activated, the drivers door only will unlock, pressing the  
unlock button a second time will cause all doors to unlock. If your transmitter  
has a sperate lock unlock buttons, pressing the unlock button anytime after  
the first unlock command will cause all the vehicle doors to unlock.  
WHILE THE SYSTEM IS SOUNDING:  
If during a triggered state, you wish to shut off the siren/horn without  
disarming your security system, simply press and release any transmitter  
button other than the disarm button. This action will turn off the siren yet leave  
the vehicle fully armed and protected. This feature is particularly useful if you  
are aware of children playing near your vehicle that may accidently trigger your  
security system. In this case you can cancel the siren/horn sounding.  
INTRUSION WARNING SIGNAL:  
This system will inform you if an intrusion attempt has occurred while you  
were away from the vehicle. Upon disarm, the siren/horn will chirp 4 times  
and the parking lights will flash 3 times. Enter the vehicle and before turning  
on the ignition switch, observe the LED flash pattern.  
If the LED flashes 1 time...pause, 1 time...pause etc., then an intrusion  
attempt was made by impact or a strong vibration that the shock sensor  
detected. Check the vehicle for possible damage to the glass or body panels.  
If the LED flashes 2 times... pause, 2 times... pause etc., then an intrusion  
attempt was made to open the hood, trunk, or by an accessory triggering  
device. Check the vehicle for indications of forced entry to these openings.  
If the LED flashes 3 times... pause, 3 times... pause etc., then an intrusion  
attempt was made to the vehicle doors. Check all doors for indications of  
forced entry.  
NOTE: The LED intrusion warning indications are stored in the system's  
memory and will be erased when the ignition switch is turned on.  
Page 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
VALET MODE:  
The valet button allows you to temporarily bypass all alarm functions,  
eliminating the need to hand your transmitter to parking attendants or garage  
mechanics. When the system is in valet mode, all alarm functions are  
bypassed, however the remote panic feature, remote door locks and remote  
start will remain operational.  
1. Enter the vehicle, and turn the ignition key to the ON position.  
2. Press and hold the valet button until the LED turns on solid. The system  
will remain in the valet mode.  
3. To return to normal operation, press and release the valet button  
any time the ignition is on.  
NOTE: Always remember to return the vehicle to the valet OFF position. This  
will ensure that the vehicle remains protected at all times.  
MANUALLYOVERRIDINGYOUR SYSTEM:  
USING THE VALET BUTTON FOR MANUALOVERRIDE  
Your security system can be disarmed without the use of the transmitter. This  
is necessary, since you will need the ability to operate your vehicle if the  
transmitter is lost or its battery fails. To bypass the alarm system;  
1. Open the vehicle door. The alarm will sound.  
2. Turn the ignition key to the ON position.  
3.  
Within 5 seconds, press and release the valet button.  
The alarm system will stop sounding and enter the (bypassed) mode. You  
can now start and operate the vehicle normally.  
Typically this override mode is used only if the transmitter has become  
inoperative.  
Programming Your Custom Override Code:  
Unlike override switches easily found, and defeated, this security system  
allows you to program a personal override code, offering a higher level of  
security. To take advantage of this option consult your installation center for  
programming details. The system comes from the factory with a pre-  
programmed override code of 11. To change this default override code, do the  
following:  
Page 6  
Download from Www.Somanuals.com. All Manuals Search And Download.  
1. Disarm the system by use of the transmitter, or by use of the emergency  
override sequence. Turn the ignition switch to the ON position.  
2. Within 10 seconds, press and release the valet/override button 3 times.  
3. Within 10 seconds turn the ignition switch OFF, ON, OFF, ON, OFF, ON.  
(The siren/horn will sound and the lights will flash one time.)  
4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing  
and releasing the button from 1 up to 9 times.  
5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch  
OFF then ON.  
6. Within 10 seconds, begin to enter your chosen units digit by pressing and  
releasing the button from 1 up to 9 times.  
7. Finish by turning the ignition switch to the OFF position.  
If the new code was accepted, the system will report back the newly entered  
code, by flashing the LED, first indicating the 10ths digit, pause and then the  
units digit. The system will report the new code three times with a one second  
pause between each code, then the system will begin arming. If the LED flash  
pattern reports the previously stored code, the new code was not entered  
correctly. Please repeat steps 1 through 7 above considering the following.  
NOTE: Acceptable digits 10ths or units are 1 through 9. The system will not  
recognize a 0 (Zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for  
more then 5 seconds during any of the above steps, the system will revert  
back to the last successfully stored code.  
CUSTOM CODE PROGRAMMING EXAMPLE:  
To change the code from the factory pre-assigned code of 11 to "52" you  
would do the following:  
1. Disarm the system by using the transmitter or by using the emergency  
override sequence.  
2. Turn the ignition switch to the ON position.  
3. Within 10 seconds, press and release the valet / override button  
3 times.  
4. Within 10 seconds, turn the ignition switch OFF, ON, OFF, ON, OFF, ON.  
(The siren/horn will sound and the lights will flash 1 time).  
Page 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5. Within 10 seconds, begin to press and release the push button switch to  
set the tenths digit. (As per example press and release 5 times to set the  
tenths digit to 5)  
6. Within 10 seconds of the last press of the button, turn the ignition  
OFF then ON.  
7. Within 10 seconds, Begin to press and release the button to  
set the units digit. (As per example, press and release 2 times to set the  
units digit to 2)  
8. Turn the ignition switch to the OFF position. Immediately observe the LED  
flash pattern. You will not the LED flashing 5 times, pause, and then flash  
2 times, pause. This pattern will be repeated 3 times indicating the new  
code (52) has been accepted and stored in memory.  
NOTE: If after step 7, the LED flashes a code other than what was just entered,  
this indicates that the code has not been changed. You will have to repeat  
steps 1 through 7 above, being certain to note the following:  
Acceptable digits, to this unit, are 1 through 9. The unit will not recognize a 0  
(zero), or no digit entered in any place, units or tenths.  
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned OFF  
for more than 5 seconds during any of the above steps, the unit will revert back  
to the last successfully stored code.  
MANUALLYOVERRIDINGYOUR SYSTEM:  
USING THE CUSTOM CODE OVERRIDE:  
Assuming the override code programmed has not been changed, and the  
default override code of 11 is in the system's memory.  
1. Enter the vehicle and turn the ignition switch to the ON position.  
NOTE: The siren will sound.  
2. Within 5 seconds, press and release the button 1 time.  
3. Within 5 seconds, turn the ignition switch OFF then ON.  
4. Within 5 seconds, press and release the button 1 time.  
5. Turn the ignition switch OFF then ON and start the vehicle.  
NOTE: If you have changed the programmed override code then substitute your  
Page 8  
Download from Www.Somanuals.com. All Manuals Search And Download.  
new code tenths for step 2 above, and units for step 5 above.  
ELIMINATING THE NORMAL ARM/DISARM CHIRPS  
You can selectively eliminate the normal arm and disarm chirps by holding the  
transmitter button slightly longer when arming or disarming. This will prevent  
the siren/horn chirps for one arm or disarm cycle. To eliminate the chirps  
permanently:  
1. Start with the valet switch in the OFF position.  
2. Turn the ignition switch ON then OFF.  
3. Within 10 seconds of turning OFF the ignition switch, press and release the  
valet button 3 times.  
4. If the chirps were on before you started, the siren/horn will emit 2 short  
chirps indicating that the chirps are now off. If the chirps were off before you  
started, the siren/horn will emit one short chirp indicating that the chirps are  
now on.  
NOTE: If the vehicle battery is disconnected then reconnected, the system will  
return to the default setting of chirps ON. Repeat the above procedure to  
eliminate the arm/disarm chirps.  
REMOTE PANIC OPERATION:  
The lock or unlock button on your transmitter also functions as a panic switch  
for use in emergency situations. To use remote panic:  
1. Press and hold the lock or unlock button of the transmitter for 3 or more  
seconds, and release. The alarm will immediately sound.  
2. To stop the alarm, press and hold the lock or unlock button of the  
transmitter again for 3 seconds. If the button is not pressed, the alarm will  
automatically stop after 30 seconds. Also if any transmitter button other than  
the lock or unlock button is pressed and released, the Panic mode will be  
turned off immediately. The normal function of this transmitter button will be  
suspended during the Panic sounding period.  
NOTE: While in the Panic mode, pressing and releasing the lock, or the  
unlock buttons will, if the option is installed, lock and unlock the doors  
respectively. While in the panic mode, anytime the unlock button is pressed,  
the panic feature will continue for the allotted 30 seconds, however, the  
security system will be disarmed allowing the vehicle to start.  
Page 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REMOTE STARTING THE VEHICLE:  
Press and release the option button of your transmitter 2 times within 2 seconds  
to activate the remote start system. The vehicle will start and remain running  
for the pre-programmed 10 or 15 minutes. As a visual indication, the parking  
lights will flash or turn on depending on the programming set up by your installa-  
tion center.  
When you arrive at your vehicle, unlock the vehicle by pressing and releasing the  
unlock button of your transmitter. Enter the vehicle and turn the ignition key to the  
ON position.  
The system WILL NOT start the vehicle if any one of the following conditions exist:  
1. The vehicle's hood Is opened.  
2. The gear shift selector is in any gear other than park.  
3. The brake is depressed.  
SHUTTING DOWN THE REMOTE START:  
To shut down the remote start feature form the transmitter press and release  
the transmitter button 2 times within 2 seconds.  
REMOTE START VALET MODE:  
Valet Mode is used to disable the system from remote starting. To enter or exit  
valet mode simply follow the 4 steps outlined below:  
1. Push and hold the programming/valet button.  
2. Cycle the ignition ON/OFF, ON/OFF, ON/OFF.  
3. Release the programming/valet button.  
4. The LED will flash 2 short flashes and 1 long flash when in remote start  
valet mode  
CAUTION! Be certain that the vehicle is outdoors before using this or any remote  
vehicle starting device. A running engine produces dangerous carbon monoxide  
fumes which can be harmful or fatal if prolonged exposure occurs. DO NOT  
remote start the vehicle if the car is garaged.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
ADDITIONAL REMOTE FUNCTION CHANNEL 3/TRUNK:  
The system has an additional feature (Channel 3) that can be connected to  
the Trunk Release. To operate the accessory associated with channel 3,  
press and hold the trunk button of your transmitter for 4 seconds.  
ADDITIONAL REMOTE FUNCTION CHANNEL 4:  
The system has an additional feature (Channel 4) that can be connected to a  
number of different optional accessories. To operate the accessory  
associated with channel 4, press and release the star " * " button of your  
transmitter. Note: The channel 4 output will remain active for as long as the  
transmitter button is held. Certain accessories may take advantage of the  
extended output capability of this channel. Check with your installation center  
for operation of the accessory that may be connected to channel 4.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CA 611 SYSTEM FUNCTIONS AT A GLANCE  
ALARM DASH MOUNTED LED INDICATORS  
RAPID FLASHING  
SLOW FLASHING  
OFF  
=
=
=
=
=
=
=
=
PASSIVEARMING  
ARMED  
DISARMED  
ON SOLID  
VALET MODE  
2 FLASH...SOLID  
3 FLASH...PAUSE  
2 FLASH...PAUSE  
1 FLASH...PAUSE  
REMOTE START VALET MODE  
INTRUSION ZONE 3  
INTRUSION ZONE 2  
INTRUSION ZONE 1  
ALARM SIREN/HORN CHIRP INDICATION  
1 CHIRP  
=
=
=
=
=
ARM  
DISARMED  
ARMING WITH ENTRY POINT OPENED  
DISARMAFTER INTRUSION  
TRIGGERED/PANIC  
2 CHIRPS  
3 CHIRPS  
4 CHIRPS  
5 CONTINUOUS  
ALARM PARKING LIGHT INDICATIONS  
1 FLASH  
2 FLASH  
3 FLASH  
CONTINUOUS FLASH  
=
=
=
=
ARM  
DISARM  
DISARMAFTER INTRUSION  
TRIGGERED/PANIC  
REMOTE START SIREN/HORN INDICATIONS  
1 LONG/1SHORT  
=
RF START COMMAND ISSUED  
(IF SELECTED ON)  
REMOTE START PARKING LIGHT INDICATIONS  
1 FLASH  
ON  
=
=
RF START COMMAND ISSUED  
RUNNING UNDER REMOTE START  
CONTROL (IF SELECTED)  
CONTINUOUS FLASH  
=
RUNNING UNDER REMOTE START  
CONTROL (IF SELECTED)  
© 2005 Code Systems, Inc  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Code Systems, Inc. Limited Lifetime Warranty  
Code Systems Inc. (“CODE”) warrants to the ORIGINAL PURCHASER of this CODE  
vehicle security product (the “Product”), purchased from an authorized CODE dealer, that (except as  
provided below) should this Product under normal use and conditions, be proven defective in material  
or workmanship DURING THE LIFETIME OF THE VEHICLE IN WHICH IT WAS ORIGINALLY  
INSTALLED, such defect(s) will be repaired or replaced (at CODE’s option) without charge for parts  
directly related to repairs of the defect(s).  
Switches, indicator lights, and transmitter cases are similarly warranted to the original  
purchaser for a period of one (1) year from the date of purchase of the Product.  
CODE accessories, sold separately, are covered by the applicable warranty accompany-  
ing the accessory.  
This warranty is non-transferable, non-assignable and is voided when: (1) the Product is  
removed from the vehicle in which it was originally installed; or (2) the vehicle in which the Product  
was originally installed is transferred to another party.  
This warranty does not apply to any product damaged by accident, physical or electrical  
abuse, improper installation, alteration, or use contrary to its intended function, fire, flood, or other  
natural acts.  
In order for the Product to be repaired or replaced under the terms of this warranty, the  
defective Product must be returned to an authorized CODE dealer and accompanied by a copy of the  
retail sales receipt. The date of purchase and year, make and model of the vehicle in which the  
Product was originally installed must be clearly indicated on the sales receipt.  
This warranty is exclusive and CODE MAKES NO OTHER WARRANTIES EXPRESSED  
OR IMPLIED. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MER-  
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, SHALL BE LIMITED TO THE  
DURATION OF THIS WRITTEN WARRANTY. IN NO CASE SHALL CODE BE LIABLE FOR ANY  
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WAR-  
RANTY, EXPRESS OR IMPLIED, WHATSOEVER.  
CODE does not warrant that the Product cannot be compromised or circumvented. THE EXTENT OF  
CODE’S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT  
PROVIDED ABOVE AND, IN NO EVENT SHALL CODE’S LIABILITY EXCEED THE PURCHASE  
PRICE PAID BY THE ORIGINAL PURCHASER OF THE PRODUCT WITHOUT INSTALLATION  
LABOR.  
Some states do not allow the exclusion or limitation of incidental or consequential dam-  
ages, so the above limitation may not apply to you. This warranty gives you specific legal rights and  
you may also have other rights which vary from state to state  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Concord Camera Digital Camera 5330z User Manual
Creda Washer W100FW User Manual
Cypress Computer Hardware CY8C20396 User Manual
Danby Range DER3009W User Manual
D Link Network Router VDI 604 User Manual
Dukane Flat Panel Television P42HC User Manual
Elation Professional Indoor Furnishings Rayzor Q7 User Manual
Electro Voice Microphone 637 User Manual
Fisher Paykel Washer IWL16 User Manual
Fundex Games Games Sea Battle User Manual