OPERATING INSTRUCTIONS FOR YOUR
®
Cobra
C O R D L E S S T E L E P H O N E
The antenna is in the phone,
not in your way...and the sound is incredible.
“
”
MODEL CP-2501
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of fire, electric shock and injury to persons,
including the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liq-
uid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not locate base unit near water, for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub, in a wet basement or near a swimming
pool.
5. Do not place this product on an unstable cart, stand or table. The product
may fall, causing serious damage to the product.
6. Slots and openings in the cabinet and the bottom or back are provided for
ventilation, to protect it from overheating; these openings must not be
blocked or covered. The openings should never be blocked by placing the
product in the bed, sofa, rug or other similar surface. This product should
never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless proper ventilation is
provided.
7. This product should be operated only from the type of power source indi-
cated on the marking label. If you are not sure of the type of power sup-
ply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not locate this prod-
uct where the cord will be abused by persons walking on it.
9. Do not overload outlets and extension cords as this can result in the risk
of fire or electric shock.
10. Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short out parts that could
result in a risk of fire or electric shock. Never spill liquid of any kind on
the product.
11. To reduce the risk of electric shock, do not disassemble this product, but
take it to qualified servicemen when service or repair work is required.
Opening or removing covers may expose you to dangerous voltages or
other risks. Incorrect reassembly can cause electric shock when the appli-
ance is subsequently used.
12. Avoid using telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
13. Do not use the telephone to report a gas leak in the vicinity of the leak.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions (continued)
14. Unplug this product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating in-
structions. Adjust only those controls that are covered by the operating
instructions because improper adjustment of other controls may result
in damage and will often require extensive work by a qualified techni-
cian to restore the product to normal operation.
E. If the product has been dropped or the cabinet has been damaged.
F. If the product exhibits a distinct change in performance.
The cordless handset operates on batteries, please read and follow instructions:
A. Use only the battery pack supplied with the unit or identical replace-
ment.
B. Do not dispose of battery pack in a fire. The cells may explode. Check
with local codes for possible disposal instruction.
C. Since released electrolyte is corrosive and may cause damage to eyes or
skin and may be toxic if swallowed:
C1. Do not open or mutilate battery pack.
C2. Always replace the entire battery pack rather than reusing one or
more cells.
C3. Do not expose batteries to heat or flame.
D. Exercise care in handling the battery pack in order not to "short" the
battery contacts with conducting materials such as rings, bracelets, and
keys. The battery or conductor may overheat and cause burns.
15. Never install telephone wiring during a lightning storm.
16. Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
17. Never touch uninsulated telephone wires or terminals unless the telephone
line has been disconnected at the network interface.
18. Use caution when installing or modifying telephone lines.
Save These Instructions
3
Download from Www.Somanuals.com. All Manuals Search And Download.
How To Use Your
®
Cobra
Cordless Telephone Model CP-2501
U.S. PATENT 4876709
U.S. PATENT 5351284
Introduction
Thank you for your purchase of a Cobra¨ Intenna® Cordless Telephone Ñ
the world’s first and only full-range-power cordless telephone without any
external antennas!
No more extending, bending, or breaking the antennas found on other cord-
less phones Ñ your Cobra Intenna conceals its antenna systems inside the
handset and base, where they should be, out of your way.
Now you can install your new Cobra Intenna cordless phone virtually any-
where. Without cumbersome external antennas to worry about, put your new
phone anywhere a corded phone can go! Then enjoy the convenience of using
your new cordless phone all over the house as well as outside in your yard.
Your new Cobra Model CP-2501 features the Opti Scanª system with 25 se-
lectable channels (the maximum number available) for optimum interference-
free use, and 10-number memory dialing. The CP-2501 is also equipped with
an extra-life battery which allows you to keep the phone away from the base
for up to 14 days between recharges, and its Clear Call® PLUS Circuitry with
compander noise-reduction system ensures corded-phone sound quality.
Please take a moment to review this booklet and become familiar with all of
the many user-friendly convenience features built into your new Cobra
Intenna Cordless Phone.
If you need further assistance installing or using your new Intenna Cordless
Telephone, please call our consumer “hotline” at 1-773-889-3087 24 hours a
day, 7 days a week.
NOTE: Some cordless telephones operate at frequencies that may cause
interference to nearby TV's and VCR's. To minimize or prevent such inter-
ference, the base of the cordless telephone should not be placed near or on
top of TV's or VCR's. If interference is experienced, moving the cordless
telephone base further away from the TV or VCR will often reduce or elimi-
nate the interference.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Information
Maximum range is obtained by installing the base unit in the highest living
area of your home. The location you choose must be near an electrical outlet
and a telephone wall jack.
INTERNAL
ANTENNA
HANDSET
TALK BUTTON
AC ADAPTER
CHANNEL
BUTTON
FLASH BUTTON
REDIAL BUTTON
TALK & BATTERY
LOW INDICATOR
MEMORY BUTTON
PULSE/TONE
SWITCH
BASE UNIT
POWER 9V DC JACK
RINGER
ON/OFF
SWITCH
FIND BUTTON
CHARGE INDICATOR
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Set-Up Guide
The following basic steps enable quick and easy installation of your new
Cobra Intenna Cordless Phone for use on a desk or countertop. You are en-
couraged to review this complete instruction manual to become familiar with
all of the operating instructions and features of your new phone.
NOTE: Before using, connect your new system to AC power (see instruc-
tions below) to charge it overnight (at least 12 hours) for optimum condi-
tioning of the rechargeable battery inside the cordless handset.
1
Insert round connector of power adapter into POWER jack (at rear of
cordless phoneÕs base; see diagram #1 below). Plug power adapter into
a standard 120 VAC household electrical outlet. Then place handset in
base so CHARGE indicator lights (see p. 12).
HANDSET
BASE UNIT—
REAR VIEW
Diagram #1
Connecting
power and
telephone
➂
ON/OFF
RINGER SWITCH
①
DC POWER JACK
4
PULSE/TONE
SWITCH
①
2
MODULAR
PHONE JACK
ELECTRICAL
OUTLET
2
After charging, remove the twist-tie from the phone cord and plug the
2
modular telephone connector into the phone jack on your wall (see
above).
3
4
Make sure that the RINGER switch is ON (located on base; see p. 11 for
details).
Set the PULSE/TONE switch (at the rear of the base) for proper opera-
tion (see page 11 for details).
Note: Make sure you have charged handset in base 12 hours
before using.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Wall Mounting Instructions
The following steps enable installation on a new or existing telephone wall-
mounting plate or directly onto a wall. (Your Cobra Intenna is designed to
be used with any AT & T, GTE, local phone company or other wall-mounting
plates that can be purchased from most local electronics stores.)
¥
¥
¥
Run telephone cord through cord wrap channel on bottom of base. (As shown).
Plug modular phone connector into telephone wall jack.
Align mounting studs on the plate to the holes on the bottom of the
Intenna base; push base onto studs and slide down on the wall plate.
Modular Phone Jack
Diagram #2: In-
stallation on a
telephone wall-
mounting plate
Mounting Studs
¥
¥
Attach the power adapter to the POWER connection (on the base of the
phone) and plug into a household AC power outlet.
To install directly on any wall, youÕll need to provide two screws and
wall anchors; follow these steps:
Ñ Drill two holes 3 1Ú4" apart and insert the wall anchors.
Ñ Drive the screws into the anchors until the head of each screw is
protruding about 1/8" from the wall.
Ñ Align the holes in the cordless base over the screw heads; push base
in and slide down on screws (see diagram #3).
Ñ Plug modular phone connector into telephone wall jack; attach the
power adapter to the POWER connection (on the base of the phone)
and plug into to a household AC power outlet.
Screw Heads
Diagram #3:
Installation
directly on a wall
7
Modular Phone Jack
Download from Www.Somanuals.com. All Manuals Search And Download.
Using Your Phone
After charging the handset batteries overnight (at least 12 hours), your
Cobra Intenna cordless phone will be ready for use.
ANSWERING/PLACING CALLS AT THE BASE
¥ To answer a call, just pick up handset from base when the phone rings.
TALK indicator will automatically light. When call is completed, return
handset to base without pressing TALK button; your phone automatical-
ly disconnects.
¥ To place a call, pick-up handset from base and press and release the
TALK button (indicator will light). When you hear the dial tone, place
your call.
ANSWERING/PLACING CALLS AWAY FROM THE BASE
¥ The TALK indicator must be off (not lit) when the handset is away from
the base. The phone is ready to
ring if a call is received (RINGER
Switch on the base must be in
ON position).
¥ Press and release the TALK but-
ton (indicator will light) to
answer or place a call.
¥ Press and release the TALK but-
ton when finished with a call.
TALK indicator light will go off
and the call will be disconnected.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cordless Phone Operational Features
The following features offer state-of-the-art performance and the ultimate in
user-friendly convenience with your new Cobra Intenna cordless telephone.
BATTERY SAVER CIRCUITRY
The handset of this phone may be kept away from the
base (TALK indicator OFF) up to 14 days at a time. In
this condition, it is ready for you to answer or place
calls by pressing and releasing the TALK button.
Note: A warning beep tone will sound and the
TALK/BAT indicator will flash when the handset
battery needs recharging (see p. 12). The duration of
the battery charge will depend on your actual use of
the phone in its remote location.
CHANNEL SELECTION
25 selectable channels are built into your Cobra
Intenna for optimum interference-free use.
If interference begins during a conversation:
¥ Press and release the CHANNEL button on the
handset. Your phone will automatically scan and
advance to the next clear channel. A confirmation
tone (two double beeps) will sound to indicate a
successful channel change.
¥ If an alert tone (3 beeps) sounds, channel change
was unsuccessful. In that case, move closer to the
phone base and press CHANNEL button again.
COMPANDER NOISE REDUCTION
Your Cobra Intenna has the Cobra Clear Call¨ PLUS compander noise-reduction
system to minimize background noise for optimum audio performance. The
sound of your phone will be comparable to the performance of a corded phone.
DIGITAL SECURITY
Your Cobra Intenna features 65,000 combinations of digital security coding
(in accordance with FCC regulations) to reduce the chance of interference
from your neighbors' cordless phones. These inaudible, electronic codes are
transmitted automatically by your phone to establish a secure link between
your cordless handset and base.
FIND
Find the handset by pressing the Find button on the base. The handset will
emit a beeping sound for thirty seconds.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
FLASH
This feature briefly interrupts the phone line so that you may access some of the
advanced featuresÑ like ÒCall WaitingÓ and ÒThree-Way CallingÓÑ that may be
offered at extra cost by your local telephone company. Press and release the
FLASH button on the handset to answer a second phone call or place a confer-
ence call if you subscribe to these services.
HEARING AID COMPATIBILITY
Your cordless telephone handset is compatible with inductively coupled
hearing aids (HAC).
SYSTEM
The revolutionary, patented Intenna hidden-antenna system is a Cobra exclusive.
Intenna is the worldÕs first and only full-range-power cordless telephone that con-
ceals the handset and base antennas inside the phone and out of the way. No
more antennas to extend, bend or break. CobraÕs hidden antennas are perfectly
matched to your phoneÕs microprocessor circuitry for optimum performance
offering the ultimate in user-friendly convenience.
LAST NUMBER REDIAL
Each time you dial, the phone number youÕre calling is automatically saved
in a special REDIAL memory. To call that number again at a busy signal, press
FLASH (without hanging up) to get a new dial tone, then press and release
the REDIAL button. If you wish to try the call in a few minutes, use TALK to
access the dial tone, then press and release the REDIAL button. The number
will automatically be redialed.
MEMORY DIALING (STORAGE)
Your Cobra Intenna cordless phone enables you to store up to ten frequently
dialed phone numbers or emergency numbers. With the TALK button off,
press and release the MEMORY button ; enter the digits of the phone number
you wish to store, up to 16 digits; press and release the MEMORY button
again. Now assign your memory number a position by entering any keypad
number from 0 to 9. You will hear a confirmation beep. NOTE: for automated
banking or alternate long distance service, you may need to program a num-
ber which is longer than 16 digits. You will need to divide the number between
two memory I.D. numbers. Follow the steps above.
MEMORY + TELEPHONE + MEMORY + I.D. # = CONFIRMATION
NUMBER
(0Ð9)
TONE
10
Download from Www.Somanuals.com. All Manuals Search And Download.
MEMORY DIALING (RECALL)
To call a number stored in memory, press TALK to get a dial tone; press MEM-
ORY button. Press the keypad number you assigned to that number and your
phone will automatically dial the number. NOTE: for longer numbers which
you have stored in two different I.D. numbers, follow steps above, pressing
MEMORY button again before entering the second number. Use the memory
sticker card provided to write down the names of each memory position. Keep
this in any covenient place.
TALK
+
MEMORY
+
I.D.#
(0-9)
= MEMORY DIAL
OUT-OF-RANGE SIGNAL
If three beeps are heard immediately after the TALK button is pressed, the
handset is too far away from the base. The handset and TALK indicator will
automatically turn off. Move closer to the base and then try your call again.
POWER FAILURE RESET
After a power failure in your home (or any time you unplug your phone from
AC power and then reconnect it), you must return the cordless handset to the
base for about 15 seconds. This automatically matches the digital security codes.
PULSE/TONE SWITCH
Your Cobra Intenna cordless phone can be used with any
phone system because it is switchable from pulse to tone
dialing (see switch on back of the base) depending on
which service you are using. Mixed PULSE and TONE
dialing may be used (to access certain long-distance or
computerized banking services, for example) by selecting
PULSE with the base switch and then using the button
PULSE
TONE
on the handset to temporarily switch to TONE dialing.
Hanging up resets to PULSE.
RINGER SWITCH
OFF
ON
The OFF/ON switch (located on back of the base) con-
trols your cordless handsetÕs electronic ringer; no ring
will sound in the OFF position.
RINGER
®
SECUR-LOC
This exclusive Cobra electronic circuitry is an added security measure to
protect your phone line from being accidentally accessed by a neighbor's
cordless phone. Secur-Loc activates automatically when your cordless hand-
set is placed into its base.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Rechargeable Battery Information
NOTE: Before using your new Cobra Intenna cordless telephone for the
first time, you must charge the battery overnight (at least 12 hours) for
optimum long-life conditioning of the nickel-cadmium rechargeable
handset battery.
BATTERY RECHARGING
When your cordless handset battery needs recharging, the following alerts
will remind you to immediately return the handset to the base for recharg-
ing (this normally requires at least 12 hours of continuous charging):
1. The TALK/BAT indicator on the
handset will flash.
2. A warning (2 beeps every 30 sec-
onds) will sound while you are
using the phone. This indicates
you have only a few minutes of
battery power remaining to com-
plete your conversation before the
phone disconnects.
3. When handset has been away from
the base and needs recharging, it
will beep at 30 second intervals for
five minutes. After this time, the
handset will seem "dead". It will
not flash or beep, nor will you be
BEEP
BEEP
able to get a dial tone. Return
handset to base for recharging.
NOTE: The CHARGE indicator will
remain on as long as the handset is in the
base, even after the batteries are fully
recharged. The batteries will not be
damaged if the handset remains in the
base continuously; the charging system
is self-adjusting and will never over-
charge the batteries.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACING THE BATTERY
The rechargeable NiCad battery in your cordless phone may need to be re-
placed if the handset will not function when the TALK button is pressed after
recharging for 12 hours.
Replacement batteries are available direct from Cobra (see accessories order
form at the end of this booklet or call 1-773-889-3087).
1. To remove the battery door, press
and slide downward.
2. Carefully disconnect the battery
pack and dispose of it properly.
See BATTERY DISPOSAL below.
3. To replace, connect the new bat-
tery and replace the door. Return
the handset to the base and
charge the battery overnight (at
least 12 hours).
NOTE: This product operates optimally with either a 2.4V, 300 mAh, NiCad
battery (supplied) or a 3.6V, 270 mAh NiCad battery (part number 213-013-9-
001).
BATTERY DISPOSAL
The rechargeable nickel cadmium (NiCad) battery in this product must be
recycled or disposed of properly in compliance with all applicable laws.
Certain states or municipalities require recycling and have established collec-
tion programs. Please contact your local waste removal authority for instruc-
tions, or return to Cobra for recycling. Wrap batteries carefully and mail
postage prepaid to:
Cobra Electronics Corporation
"Contains Nickel-Cadmium Re-
6500 W. Cortland Street
chargeable Battery. Must be
recycled or disposed of proper-
Chicago, IL 60707
Attn: Battery Recycling
DO NOT PUT BATTERIES INTO
FIRE OR EXPOSE TO HIGH HEAT.
THEY MAY EXPLODE.
CLEANING THE CHARGING CONTACTS
Ni-Cd
Clean the two metal charging contacts on the base and handset with a soft,
dry cloth on a regular basis to ensure optimum performance of the battery-
charging system. Rubbing alcohol may be used if more thorough cleaning is
required.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
About Cordless Phone Performance
Your Cobra Intenna cordless phone uses radio transmission to communicate
between the base and handset. It is thus subject to occasional interferenceÑ
static or buzzing noises, for example. These conditions may be caused by
electrical motors on household appliances, fluorescent lights, electrical storms
and other sources.
These steps will enhance the maximum performance of your new phone:
•
Change channels by pressing the CHANNEL button on the handset
if you experience interference.
•
Don't cover the upper section of the cordless handset with your
hand (see diagram below). This may block the internal antenna locat-
ed at the top of the handset, possibly reducing the phone's range and
audio clarity. Always hold the handset at the middle or close to the
bottom.
Hold the
cordless handset at the
middle or bottom area
of your phone for
best performance.
INCORRECT
CORRECT
•
•
Avoid resting the handset on your shoulder during conversations;
this may also block the performance of the internal antenna.
Don't plug your phone's power cord into an active AC outlet that also
provides power for a major appliance or for charging units for cordless
appliances (vacuums, screwdrivers, etc.) or other electronic devices.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cordless Telephone
Troubleshooting Guide
If your cordless phone does not seem to operate properly, please check the
following and refer to the appropriate sections in this booklet for detailed in-
formation:
¥
¥
The phone is dead; no indicator lights are on: Are the power cord
and telephone cord connected?
Handset beeps during conversations or when away from the base:
The batteries need recharging; return the handset to the base for
overnight recharging.
¥
¥
Hearing poor audio or added interference during calls: DonÕt
cover the top section of the handset with your hand or rest the
phone on your shoulder. This blocks the special internal Cobra
Intenna handset antenna.
Handset disconnects, loses performance and/or beeps three times
when in use away from the base: You may be out of range or your
batteries may need recharging. Move closer to the base and/or re-
charge batteries.
¥
¥
Unable to make a call due to interference: Select a new channel.
Handset won’t work after a power outage or after disconnecting
phone from AC power and then reconnecting it: Return the hand-
set to the base for about 15 seconds to automatically match the secu-
rity coding.
¥
¥
Handset seems "dead.": Battery power has run out; return handset
to base and charge for at least 12 hours. If handset still seems dead,
unplug the handset battery for 15 seconds and plug back in and
then place the handset back on the base for at least 5 minutes.
Memory dialing does not work: Handset battery may have become
completely discharged; recharge handset in cradle (12 hours) then
re-enter your memory dialing numbers (see p. 10).
15
Download from Www.Somanuals.com. All Manuals Search And Download.
For technical assistance, please call our Automated Help Desk
which can assist you by answering the most frequently asked
questions about Cobra products.
(773) 889-3087
24 hours a day, 7 days a week.
A consumer Service Representative can be reached through this number
8:00 am - 8:00 pm, Monday through Friday, CST.
If You Think You Need Service Call 1-773-889-3087
You may be asked to send your unit to the Cobra factory. It will be necessary to furnish
the following in order to have the product serviced and returned.
1.
For Warranty Repair include some form of proof-of-purchase, such as a mechan-
ical reproduction or carbon or a sales receipt. If you send the original receipt it can-
not be returned.
2.
3.
4.
5.
Send the entire product. For exampleÑmust include base, handset, cords and
power adapter furnished with the product.
Enclose a description of what is happening with the unit. Include a typed or clear-
ly printed name and address of where the unit is to be returned.
Pack unit securely to prevent damage in transit. If possible, use the original pack-
ing material.
Ship prepaid and insured by way of a traceable carrier; such as United Parcel
Service (UPS) or First Class Mail; to avoid loss in transit to Cobra Factory
Service, Cobra Electronics Corporation, 6500 W. Cortland St., Chicago, IL 60707.
6.
If the unit is in warranty, upon receipt of your unit it will either be repaired or
exchanged depending on the model. Please allow approximately 3 to 4 weeks
before contacting us for status. If the unit is out of warranty a letter will automati-
cally be sent informing you of the repair charge or replacement charge. If you have
any questions, please call 1-773-889-3087 for assistance.
Registered with the FCC
Please note: This cordless telephone operates under part 15 and part 68 of FCC
rules. Operation is subject to two conditions: 1) It may not interfere with radio
communications, and 2) It must accept any interference received, including that
which may cause undesirable operation. See the Operational Features section of
this booklet for ways to reduce interference.
Your telephone company is required by the Federal Communications Commission
to allow you to connect FCC registered telephones to their lines.
The FCC requires you to provide information, if requested by the local telephone com-
pany, about the connection of an FCC registered telephone to their lines. They may ask
you for the FCC registration number and the ringer equivalence number (REN), both
of which are on the bottom of the base. They may also ask for the Universal Service
Order Code (USOC) number, which is RJ-11C.
It is illegal to use this phone on a party line or to connect it to a coin-operated telephone.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Limited One-Year Warranty
COBRA ELECTRONICS CORPORATION warrants that its COBRA cordless
telephone products, and the component parts thereof, will be free of defects in
workmanship and materials for period of one (1) year from the date of first con-
sumer purchase. This warranty may be enforced by the first consumer purchas-
er, provided that the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective cordless
telephone products or component parts upon delivery to the Cobra factory
Service Department, accompanied by proof of the date of first consumer pur-
chase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for war-
ranty service. The return charges will be at CobraÕs expense if the product is
repaired or replaced under warranty. For further details concerning procedures
for obtaining service, see the ÒIf You Need ServiceÓ section of this OwnerÕs
Manual.
Exclusions: This limited warranty does not apply 1) to any product damaged
by accident, improper line voltage or weather related circumstances; 2) in the
event of misuse or abuse of the product or as a result of unauthorized alter-
ations or repairs; 3) to non-defective original equipment Nickel Cadmium re-
chargeable batteries; 4) if the serial number has been altered, defaced or re-
moved; or 5) if the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness
for a particular purpose, are limited in duration to the length of this warran-
ty.
Cobra shall not be liable for any incidental, consequential or other damages,
including, without limitation, damages resulting from loss of use or cost of
installation.
Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
This limited warranty gives you specific legal rights, and you may also have
COBRA ELECTRONICS CORPORATION
6500 W. Cortland Street
Chicago, Illinois 60707
In addition to its exclusive series of Intenna cordless telephones and
answering systems, Cobra is also one of AmericaÕs leading brands of CB
radios and accessories, and Safety Alertª radar/laser detectors.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cobra Cordless Phone Accessories
Description
Part No.
Cost Ea. X Qty. = Amount
NICKEL-CADMIUM BATTERY PACK ASSEMBLY
WITH CONNECTOR
For use with model CP-2501
$15.00
213-013-9-001
AC POWER ADAPTER
For use with model CP-2501
768-026-N-001 $15.00
★★ Illinois residents add 7%
Amount
★★ Cook Co. residents add .75% (7.75% total)
★★ Chicago residents add 1% (8.75% total)
★★ Indiana residents add 5%
(Tax if applicable
)
Shipping//handling
$3.50
★★ Michigan residents add 4 %
★★ Minnesota residents add 6%
★★ Ohio residents add 6%
Total
★★ Wisconsin residents add 5%
Make check or money order (no stamps) payable to:
Cobra Accessories Dept.
6500 W. Cortland St., Chicago, IL 60707
Call 1-773-889-3087 or fax 1-773-622-2269 for credit card orders
Allow 4 to 6 weeks for delivery. Offer valid in Continental U.S. only.
Please print clearly:
Name
Address (Not P.O. Box)
City
State
Zip
Exp. Date
Credit Card No.
Customer Signature
Circle One:
Visa
MasterCard
Discover
Download from Www.Somanuals.com. All Manuals Search And Download.
®
Cobra
Cobra Electronics Corporation
6500 W. Cortland Street
Chicago, IL 60707
PRINTED IN MALAYSIA
© 1997 COBRA ELECTRONICS CORPORATION
480-158-P-001
Download from Www.Somanuals.com. All Manuals Search And Download.
|